“FOR ADVANCE LEARNERS”

PREVIOUS YEAR UNIVERSITY QUESTION &

ANSWER FOR THE SUBJECT “WET PROCESSING“

PREPARED BY

MRS. D. JEYA PRADHA, B.E., M.B.A

Lecturer in Department of Fashion Technology & Costume Designing.

SHRI MATI INDIRA GANDHI COLLEGE.

Wet Processing

Part – A

Answer the following questions:

1. List out the properties of direct Dyes?

The properties of Direct Dyes are:

Direct dyes are readily soluble in water.

Some of the dyed need a little amount of soda ash (sodium carbonate) to completely

dissolve them in water.

Direct dyes are used for dyeing cotton, viscose rayon, wool and silk fibres.

Direct dyes have poor wash in fastness and poor light fastness.

There fastness properties can be improved by certain after treatments.

2. What are the types of calendaring?

There are seven types of calendaring. They are

a. 7 – Bowl calender

b. Swizzing calender.

c. Chasing calender

d. Transrfer calender

e. Friction calender

f. Schreiner calendar (and)

g. Fett calendar.

3. What is meant by shrinkage?

Shrinkage is the contraction in the dimension of the fabric due to usage. Cotton fabric

suffers from 2 main disadvantages of creasing and shrinkage during subsequent washing.

Creasing is overcome by the Resin finishing where as the shrinkage is prevented by a special

finishing known as sanforising and the machine used for that purpose is known as sanforising

and the machine used for that purpose is known as zero- zero pre shrinkage machine.

4. What is meant by water proofing?

Water proofing:

Water proofing is nothing but preventing the passage of both air and water through a

fabric”.

5.What is meant by continuos Desizing?

Continues Desizing:

Normally when matt extract is used as a desizing agent. It takes about 3-4 hours for

complete desizing. But if use increase the concentration of the malt extract the time will be

reduced to 5 minutes.

6.What is Mercerisation?

Mercerisation:

Mercerisation improves the luster of cotton fibres. It also gives the cotton material a

greater affinity for colouring matters. Tension during mercerization is essential for to

improve the luster. Mercerisation produces a permanent change in the structure of cotton

fibre. Mercerization is a process in which the cotton material is treated with 25% to 30%

(50oC to 65oC Tw) Na OH solution and under tension at room temperature.

7.What is Napping?

Napping:

Napping is chiefly used to obtain a relatively deep hairy surface, but the degree of depth

depends upon the technique used. On the other hand, napping may also serve to cover up a

sleazy construction and weaving imperfections.

8. What are different styles of printing?

Styles of printing:

The different styles of printing are:

direct style

discharge style (and)

resist style

9. What are the Dye molecules?

The Dye molecules:

Dye molecules are organic molecules which can be classified as:

Anionic

Cationic (and)

Disperse

Anionic:

In which the colour is caused by the anionic part of the dye molecule.

Cationic:

In which the colour is caused by the cationic part of the dye molecule.

Disperse:

In which the colour is caused by the whole molecule. The first two dye molecules types

are appliede from an aqueous solution. The hird is applied from an aqueous dispersion.

10. What is finishing?

Finishing is one of the essential processes of a processing mill where all bleached, dyed

and printed material are subjected before they are put on the market. The aim of the tertile

finishing is to render textile goods fit for their and uses.

PART-B

Answer the following questions:

11.a) Write short notes about Scouring ?

Scouring

After desizing and through washing the cloth contains oils, fats,waxes, seed bits , leaf

particals, and natural colouring matter etc.These oils , fats, waxes are hydrophobic or water

hateing characters . so if these compounds present in the cloth., they affect the absorbency of

the cloth. These leads to imoproper dyeing , printing,and printing subsequent

process.scouring is carried out in a boilers called as kier

Two types of kiers are.

Horizontal kier

Vertical kier.

Vertical kiers

Scouring process is carried out commonly in vertical kier boilers usually underhigh

pressure 20 – 30 lbs/sq. inch and temperature 120o-130o with 8 to 24 hrs , depend upon the

type of fabric.

High pressure , high temperature vertical kier:

The vertical kier as shown in the figure . the kiers consists of a cylindrical vessel

made up of a cast iron . The inner portion is coated with a lime wash to prevent the

formation of rust stains on the fabric.

The desized fabric is placed inside the kier uniformly by manually or mechanically . It

is called as packing or pilling Pacing should be done evenly . uneven packing result in

uneven scouring.

The top of the kier is provided with cover known as lid. Usually boiling is carried out

with 3% NAOH.

A requird amount of sodium hydroxide is dissolved in water. This liquor is filled in

liquor is filled in liquor container. From the liquor container. The liquor is pumped with the

help of centrifugal pump.

Them the liquor reach the heater, at that time the solution is heated and the heated

solution is passed through the sprayer.

The sprayer is placed above the fabric. The heated solution is sprayed on the fabric and then

reaches the liquor container with the help of perforated false bottom. This operation is

repeated for 8 hours.

After the time is over the pressure is released. The liquor is taken out through

drainage.

The cloth is washed with hot and cold washes two or three times and then the cloth is

taken out for further process.

Caustic Soda boiling is used for Fine counts, super Fine counts varieties and delicate

fabric structured material etc.,

Scouring liqueur is prepared as follows:

NaCh -- 3.0%

Soap -- 0.5%

Wetting agent -- 0.5%

(Turkey Red Oil)

Sodium silicate-- 1.0% (to retain heat stability)

Material to liquor ratic-- 1:4

Temperature -- 120oC to 130oC

Time -- 8 hours

Pressure -- 20 to 30 1bs/sq.inch

Precautions:

1. When the scouring operation is strated , remove the air completely inside the kier ,

changes of formation of oxy cellulose . It will damage the fabric.

2. Packing should be done uniformly . Uneven packing results in uneven scouring.

3. After packing the top portion is converted with heavy stones or thickly variety of

fabric to prevent hot liquor directly falling on the fabric.

4. After scouring is over , washing is also done inside the kier , otherwise oxy

cellulose will degrade the cotton material.

11.b) Explain detail about “J Box Bleaching” ?

Impregnated the material with 5% to 7% NAOH at 70oC

Passed through the pre heater ( 90oc to 100

oC )

Reached „J‟ Box , Time 60 – 90 min . Temperature 90oC- 100

o C

Hot and Cold Wash

Impregnate the scoured material with H2O2 ( 5% -7% )

Passed through the heater ( 90oC – 100

oC)

Reach „J‟ Box (60 -90 min , Temperature 90o -100

oC

( bleaching process)

Cold Wash – Scoured and bleached material.

Ready for further process .

The cloth is now in a perfectly white condition .normal recipe used peroxide

bleaching is as follows .

Hydrogen Peroxide - 5% -7% (Weight of the fabric)

Sodium Silicate - 3% (Weight of the fabric)

NAOH - 0.4 % - 6.0 % (Weight of the fabric)

Soda ash - 0.8% -11.0 % (Weight of the fabric)

PH - 10.3 -10.8

Temperature - 900oC-100

oC

A modern tendency of continuous bleaching process based on the principle of

„J‟Box . both scouring and bleached process is done in a single process .

First the cloth is impregnated with NAOH solution with the help of the guide

roller kept at 71oC and then the cloth is passed through the pre heated chamber . The material

is heated 90oC to 100

oC

The hot material next passes through the „J‟ Box . From „J‟ box to water trough the

time taken is 60 – 90 minutes , at that time scouring process will takes place , this period is

called as dwell period . if „J‟ Box is well insulated to retain heat and it is lined with

stainless steel .

After the scouring is over the material passed through the water trough contains the

hot water to give hot wash and then passed through the another water trough to give cold

wash as shown in the figure . The scoured material is impregnated with Hydrogen Peroxide

(H2O2 ) strength about 3% - 7% and passed through the second heater and the material is

heated .

The hot material is now reaching the „J‟ Box . The time taken is 60 – 90 minutes at

that time bleaching operation is taking place . Finally the material is washed in water trough .

Now we will get scoured and bleached material in single process.

Advantage :

1. It is very fast process than the other process .

2. Production is more

3. Both Scouring and bleaching are done in a single process.

4. It is very economical when longer length of fabric is to be bleached .

12a). Write about the general theory of Dying? And explain the fastness – Properties of

Dyes?

The General theory of Dying:

Dying is the process of colouring textile material by immersing them in an aqueous solution

of dye, called dye, liquor. Normally the dye liquor consists of dye, water and auxiliary.

The general theory of dyeing explains the inter action between dye, water and dye

auxiliary. More specifically, it explains:-

forces of repulsion which are developed between the dye molecules and water and

forces of attraction which are developed between the dye molecules and fitness.

There forces we responsible for the dye molecules leaving the aqueous dye liquor and

entering and attaching themselves to the polymers of the fibres.

FASTNESS – PROPERTIES OF DYES:

COMMON PROPERTIES REQUIRED OF A DYE:

When a dye is present on a fabric, it is expected to have certain properties. When a

dyed (or) printed fabric is exposed to sunlight during its use, the dye should not fade

(or) change in colour. That is it should have high light fastness.

The dye should posses good washing fastness. If the cloth dyed with it is used for

making garment. Otherwise staining of garments with stripped dyestuffs occurs

during the washing of many garments together.

The dye should have good perspiration fastness when people wearing coloured

garments perspire, a part of the dye coming into contact with the perspiration may be

stripped and stain the skin of the water.

Apart from these properties the dyes can be expect to have good fastness to gas fading

incites gases like sulphur, nitrogen – dioxide, may be present in the atmosphere and

the dye may be affected. Dye polyesters and polyamide fabrics are exposed to very

high temperatures during processing -------textile mills. At this temperature some of

the dyes submit off. For this purpose, the dyes used on the fabric should have good

sublimation fastness.

A dye need not have good fastness to all the agencies. A dye intended for dyeing (or)

printing certain cloth need not be fast to perspiration but should have very good light fastness.

Therefore, dyes have to be selected depending on the use of the fabric to which it is put.

12.b).Explain about dying of cotton with sulphur dye ?

The dying is carried out in the following four stages .

1. Dissolving

2. Dyeing

3. Oxidation

4. After treatment.

Dissolving :

In dissolving , the insoluble sulphur dye is converted into soluble leuco dye.

The dye is taken as per shade and pasted with small quantity of Tirkey Red Oil and

cold water .

Soda ash (Na2Co3-1/2 the quantity of dye ) and sodium sulphide (Na2S -1.5 times of

dye ) are added one by one and stirred. Boiling water is poured in and stirred . The

solution is boiled for 5-10 minutes if necessary . Sodium sulphide reduces the dye into its

leuco form . Soda ash neutralizes the acidity of the dye . The insoluble sulphur dye is

converted into soluble sodium salt ( Leuco Form ). Original colour of the solution is

changes into reduced colour .

Dyeing :

Fabric is loaded in the machine. The dye bath is set up as Per M:L ratio.Bath

temperature is raised to 50oc. Circulation of liquor or material is started . The dye bath

should have sufficient quality of sodium sulphide and soda ash . PH of the bath is10 -11.

5 min

The pre dissolved dye solution is added. Bath temperature is raised to 90oC - 100oC.

The fabric should not expose in the atmosphere as the oxygen in the air may oxidize the

dye and causes „ Patches „.

5 min

10 – 20 20 gpl Glabour salt or comman salt is added in two instalments with a time of

interval of 15 minutes . The dyeing is continued is continued for further process

45 min – 60 min . Dye penetrates well into the fibre molecule .

The material is squeezed ( It should not be washed )

Oxidation :

The leuco dye inside the fibre molecule is oxidized into its original insoluble form.

The dye molecule is mechanically trapped inside the fibre molecule and hence it can not

come out in subsequent washing . There are two types of oxidation namely

I) Air oxidation

II) Chemical oxidation

In air oxidation , the material is exposed to atmospheric air for 15 min

In chemical oxidation , the material is treated with 1-3 gpl sodium perborate or

2 gpl H2O2 with 1 gpl acedic acid .

After Treatment:

The fastness to light and washing of sulphur dyes is improved by after treatment with

the following solution . It should never be done for sulphur black .

1.25% Potassium dichromate ( K2Cr2O7 – To improve wash fastness)

1.25% Acedic acid (60%)

1.25% copper sulphate ( CUSO4 – To improve the light fastness )

at 60oC for 30 min

Hot Soaping – 5gpl soap and ash at 80oC for 15 min

Cold wash for 15 min

Bronziness :

Bronzing of shade is nothing but an unwasnted glittering patches on surface of fabric , most

commonly occurring fault with sulphur blacks and blues which is caused by

1. Excessive delay in washing off the material after it is taken out from the dye bath .

2. Excess of dyestuff on the material or too much salt in the bath .

3. Insufficient sodium sulphide in the dye bath and due to it incomplete solution of

the dye stuff which results in surface dyeing of the material where it is quickly

oxidized by contact with the atmosphere

Bronziness can be removed by treating the dyed material in boiling soap or sodium

sulphide solution.

Sulphur Black Tendering :

Sulphur black tenders and dyed material . It has been attributed to the presence of

free sulphur , which gets converted in to sulphuric acid on storage that degrade cotton by

hydrolysis of cellulose . The sulphur black dted material should not be treated with copper

sulphate as it is tendered more rapidly . the danger of tendering on storage can bre reduced by

treating with potassium dichromate followed by washing with 8 gpl soda ash .

13a) Brief on Block Printing ?

Block printing is the oldest and the simplest method of printing . Because of its

artistic and decorative value and the purity and richness of colour produced by it the method

it still used in many countires of the world .

The blocks used in this method are made of several layers of comman timber which

are comented together and the portions to be printed are carved or raised in relief on a thick

block of wood . Metalic blocks such as „T „ japs are used for special work as in Batik Printing

In block printing 10 – 40 needles is used in this instrument . Colour in the form of a

thickened paste is applied to the raised parts of the block and the impression of the design is

obtained by stamping the block by hand with a wooden mallet and the cloth should be

printed .

Each shade of a colour requires a separate block and in very large3 patterns , each

individual colour may require more than one block . Thus in a design called “ Dutch Boquet “

Which has 23 colours in it , 126 Blocks are used for printing the designs .

Procedure :

The colour paste is spread on the woollen cloth of the sleve „a‟ . the block is carefully

placed on this sieve and pressed twice (or more ) so that it picks up auniform layer of paste ,

it is picks up auniform nlayer of paste , it is then stamped on to the cloth on the table by

giving belows or striking it with a small but heavy mallet ( or hammer ) to ensure a clear

impression . A separate sieve „a‟ is required for each colour but the same swimming tup can

be used over and over again . By repeate stamping of the colour paste , the pattern is built up

and process is repeated until all the colours are seperatly applied and the whole piece of cloth

is printed . It is then removed , dried and given appropriate after treatment .

Advantage :

a. The method is simple to operate and does not reouire elobrate and expensive

equipment .

b. Designs in any number of colours and on any scale can be reproduced with ease

and certainly by this method .

c. First – rate block prints possess richnss , fullness and purity of colours

Disadvantage :

a. The method is slow and therefore , has a low output and its cost is high .

b. For printing block designs or designs with very long or wide repeats , it is not

possible to use a large – sized block of great weight because the printer will not be

able to manipulate properly such a block .

c. The method involves manual work , it is therefore ,quite laborious .

13. b ) Write notes on Duplex Printing and Warp printing ?

Duplex Printing :

Duplex printing stimulates a woven pattern by printing the fabric on both sides . The

fabric may be passed through the roller printing machine in two separate operations or

through a duplex printing machine in a single operation or through a duplex printing

machine in a single operation . Duplex printing produces an equally clear outline on both

sides of the fabric . The designs is applied so skillfully by careful registration of the printing

cylinders that the result may be mistaken for a woven designs . The difference can be

detected by raveling a yarn .

Warp Printing:

Warp printing is roller printing applied to warp yarns before they are woven into

fabric . fine white or neutral – colored filling yarns are generally used for weaving so that the

designs on the warp will not be obscured . This methods produces designs with soft ,

nebulous , but striking effects . Great care must be taken to keep the warp yarns in their

proper position so the outline of the designs will be preserved , warp printing is used for

expensive cretonnes are upholstery fabrics .

A variation of warp printing is vigoreux printing of mélange . Utilizing a variation of

roller printing , horizontal or cross – striped designs are printed on the ropelike woll tops or

slubbings . Subsequently when the tops are spun in to yarn , the stripes are attenuated and

pulled apart so that they appear scattered flecks of color in the woven cloth.

14 . a) Write Short Note on Friction Calender ?

Calendering :

Object:

To upgrade the fabric handle and to impart a smooth silky touch to the fabrics.

To compress the fabric and reduce its thickness

To improve the opacity of the fabric

To reduce the air permeability of the fabric by changing its porosity

To impart different degree of Lustre to the fabric.

To reduce the Yarn Slippage.

Friction Calender :

For producing this effect , the top four bowls of a 7 bowl calendar can be lifted up ,

disconnecting the contact between the third and the fourth bowls so as to use only three

bowls.

The above diagram is a friction calendar with a 7 bowl calendar after disconnecting the

top four bowls .

The three bowl calendar , one of which is cotton and the other two or of chilled iron .

Friction calendering gives a higher Gloss and greater closing of the yarns , it is produced

by bringing the cloth in contact with a heated polished chilled iron bowl is rotated at double

the speed of the fabric and of the lower two bowls .

As the variation , the top bowl may be run at 11/2 times the speed of the lowest bowl , with

the middle bowl running at an inter mediate speed .

The top bowl with its higher surface speed produces the friction effect by polishing the

cloth .

This finish is generally imparted to loose construction cloth such as binding cloth , low

quality printed cloth etc., .

It is generally run at a speed of 32 mts/min .

The speed of the calendar when used in friction calendaring is determined by the amount

of finish desired on the fabric and by the number of bowls used.

14.b) write notes on Flame Retardan Finish for cotton ?

Theories and mechanism of flame Retardency :

1. Coating theory:

Flame retardance is due to formation of alayer of a fusible substances which

melt s and forms a coating thus excluding the air necessary for the propogation

of flame . carbonates and ammonium salts liberates gases like CO2, NH3 and

exclude air .

2. Gas theory :

The flame retardant decomposes at burning temperature and develops non

combustible gases which obstruct and dilute the combustible gases . Eg .

Mixtures of titanium and antimony oxides .

3. Thermal theory :

Heat supplied from the source is conducted from the fibres very rapidly that

the fabric never reaches the temperature of the combustion .

4. Chemical theory :

The flame retardants react with cellulose on burning and forms chemicals

such as phosphoric and sulphuric acid which are dehydrating agents , these

brings about catalytic dehydration of cellulose , which on combustion

produces mainly carbon water .

Flame retardant finish for cotton:

First method:

By depositing insoluble metallic compounds , the effect of fire proofing

obtained is permanent as it does not wash out .

Out of all Antimony Oxychloride is the best .

It is precipitated on the fibre by the double decomposition of tartaremetic and

stannic Oxychloride and then washed in running water .

In the same manner . Metallic Salts such as Magnesium Borate , Ammonium Sulphate and

Magnesium Silicate also produce fire proofing

Second Method :

Soluble Compounds such as Borax . Sodium Phosphate are used . A mixture

as given below is found to be effective for this finish .

Borax - 50 Parts

Boric Acid - 35 Parts

Sodium Phosphate - 15 Parts

Only 5% Solution of the mixture is used .

Most of the fire proofing agents can be fixed by synthetic resins .

Most of the fire proofing agents can be fixed by synthetic resins.

Tetrakis Hydroxy Methyl Phosphonium Chloride (THPC) . when used with Urea and

Methylol . Melamine produce good wet fastness flame proofing properties .

The fabric is padded through the solutiojn containing .

THPC - 15.8 %

Methylol melamine - 9.5%

Tri ethanol amine - 3%

Urea - 9.9%

Dried and cured at 140oC for 5 mins and washed . This process is known as „proban „

finishing .

Process Sequence :

Pad – Dry – Cure

15 a). Classification of finishes? Explain types of finishing?

Finishing:

Finishing is one of the essential processes of a processing mill where all bleached,

dyed and printed material are subjected before they are put on the market. The aim of the

textile finishing is to render textile goods fit for their and uses

Classification of Finishes

Textile finishing

Chemical mechanical

Reactive type of finish Deposition Temporary Permanent

Eg:- parchmentising (stiff and Eg . Calendering Eg.Raising

Transparent chlorination of wool Sanforising

(anti shrink) mercersing velan

PF (Flame retardant) Ethylene Temporary Permanent

Oxide-Formaldehtyde (soil release) Eg:- starch china clay Eg:- synthetic

phosphorus and Nitrogen waxes (soft) optical Brightening.

compounds (stiff) oils fats and Brightening. china clay (stiff)

Flame retardant) rubber, coating

All ARE PERMANENT. (water proof)

cellulose acetate,

cellulose

Types of finish:

Finishing mainly falls into three groups:

Temporary finish.

Permanent finish (and)Semi – Permanent finish

Temporary finish:

A finish which is not stable and goes off after the first wash is known as

“TEMPORARY FINISH‟

If the finishing effect in the fabric disappears during subsequent washing and usage

then it is called “TEMPORARY FINISH”

For example : Mechanical : Calendering, Embossing etc.,

Chemical : starching, softening (Except Reactive softness)

Permanent finish:

If the finishing effect in the fabric does not disappear and remains unaffected through

all the conditions of wear and washing treatments, then the finish is said to be a

“PERMANENT FINISH”.

For Example:

Mechanical : sanforising, mechanical mills of wool, etc.,

Chemical : Resin finishing, water proof, flame proof finish, etc.,

Semi – permanent finish:

A finishing on the fabric is said to be “ SEMI PERMANENT FINSH” if it is stable to

more than 5 to 10 wases and not agterwards.

For Example: Mechnical : schreiner Calendering

Chemical : Buckram finish

5.b) What is Decatising ? Explain with Diagram?

Decatising:

This is also a finish similar to felt calendaring mostly meant for woolenfabrics. But

today all suitings are decatisod.

Both batch and continuous methods are available:

Essentially, this is a stress – Relaxation process.

The function of setting is to relax the various

Stresses built up in the material during spinning and weaving to stabilize the fibres in the new

and desired construction.

Wool fibre contains small quantity of Thiol groups (-SH). It can be converted into

Disulphide bond (-S-S) by reaction of wool with a reducing agent or by the action of hot

water, steam or alkalies.

This interchange reaction and hydrogen bond rearrangement are important in wool

setting.

Mechanism:

The fabric is compresse between two layers of woolen felt and steam is blown

simulttareously. The fabric acquires body, suppleness with ironing effect on both the faces.

These are due to the swelling of the fibre by steam.

Parameters:

The effectiveness of decatusubg depends on

1. Type of fibre.

2. Time of contact

3. Amount of contact

4. Tension

5. Type of finish desired

DECATISING MACHINE

1. Steam Heated Cylinder

2. Exgayst

3. Steam kube

4. woolen felt.

5. Table

6. Finished Material

process:

Without the fabric felt is run forward and backward for 15-30 minutes. The fabric is

fed along with the woolen felt. The amount of fabric to be fed depends on the length of the

woolen blanket.

Normally one piece is fed. The piece is cut at the joint. The chamber door is shut and

the steam is opened and maintained at a pressure of 10- 15 PSI. the felt is run forward and

backward with the help of reversible motor for 5 minutes.

After the treatment time, (Normally 7 minutes) steam is shut off and the fabric is

collected and laid on the table.

Chemical Decatising:

It will give a full soft feel.

Normally sodium Bisulphide is used at a concentration of 10-20 gpl.

Pad – Dry – Steam

Padding is done at an expression of 50% on a padding mangle.

Steaming is done by winding the material on a perforated beam of a decatising

machine and steamed for 3-5 minutes followed by the application of vacuum till the fabric

cools.

10 Marks

16. Write about the process sequence for cotton? Explain?

Cotton:

Process sequence for cotton:

Row Meteraial (cotton Grey fabric)

Singeing

Desizing

Scouring

Souring

Bleaching

Mercerizing Dyeing printing

After treatment (Both chemical

Mechanical process)

Singing :

Removal of loose hairy fibres protruding (or) projecting from the surface of fabric by

burning is called “singeing”

Object of singeing:

Singeing is the process of removing the loose hairy fibres protruding from the surface

of the fabric by burning. These are done to give a smooth, even and clean looking face to the

fabric.

Desizing

Desiing is the process of removal of siaing material deposited on the fabric during the

sizing operations.

Object of Desizing :

The object of desizing up of the pores of the fibres. This makes the fabric soft & more

absorbent.

Recipe:

Hydrochloric acid = 0.5-1%

Sodium chloride = 0.5-1%

Condition :

Time =1-2hrs

Temperature = room temperature(R.T)

Ph = 4-4.5

Material to liquor ratio = 1:20

Scouring:

After desizing and through washing the cloth contains oils, fats, waxes, seed bits, leaf

particles and nature clouring matters, etc., these oils, fats, waxes are hydropholic or water

hating characters. So if these compounds present in the cloth, they affect the absorbency of

cloth. This leads to improper dyeing, printing and finishing in subsequent process.

Recipe:

Sodium hydroxide = 3%

Soda ash = 2%

Wetting = 1%

Condition:

Material to liquor ratio = 1:30

Temperature = boiling temp

Duration = 2-3 hours.

Souring

This process is done to neutralize the fabric. This process is done mostly after every

process.

Bleaching:

Bleaching is the process of removal of natural coluoring matter (yellouwish grey

colour) persent in the textile material by using NaOcL, CaOcl, H2 –O2, SO2, etc.,

Recipe:

M2 O2 = 4

Sodium silicate = 4.8 gms / lit

Sodium Carbonate = 0.5-1 gms/lit

Condition:

Ph = 10.5 -10.8

Temperature = 1 to 2 hrs

Time = 1 to 2 hrs

Material to liquor ratio= 1:50

Mercerizing:

Mercerisation improves the luster of cotton fibres also gives the cotton material a

greater affinity for colouring matters. Mercersing consists of impregnating the cotton material

with cold 25% to 27% caustic soda.

Object

To improve luster of the fabric

To increase the strength of material.

To give good dye absorbing capacity to cotton

To remove crease from fabric

To increase hydroscopicity property

Dyeing:

Dyeing is the process of colouring textile materials by immersing them in an aqueous

solution of dye, called dye liquor. Normally the dye liquor consists of dye, water and

auxiliary.

A dye stuff is a substance which is capable of colouring a textile materials in such a

manner that it associates closely with the fibres.

There are 2 types of colouring matters. They are Dyes & pigments. Dyes also is

divided into 2, they are insoluble dyes.

For Example:

Vat, sulpher, etc, are insoluble dyes. Reactive dyes are soluble dyes and are widely

used for dyeing cotton products because of their wide range of shades availability. Excellent

fastness property moderate dyeing rate (or) cost of dye/kg.

Printing :

It is a process of producing attractive designs on textile fabrics using one (or) more

dye stuffs. Printing is localized dyeing. Printing is nothing bur applying colors with in

boundaries of the designs.

Styles of printing:

Direct style

Discharge style

Resist style

The different styles can be done by using different printing methods like block, screen

flat bed screen, rotary screen, transfer printing, etc.,

After treatment:

After dyeing (or) printing, fabric is taken to after treatment by means of washing and

soaping treatment.

Objective:

To remove the unfixed dye stuff and chemicals from the fabric.

To avoid the bleeding of colours during subsequent washing.

Finieshing:

Finishing is one of the essential process of a processing mill. The aim of textile finishing is

render textile goods fit for their end uses.

Objects:

improved appearance – luster, whiteness, etc.,

improved feel which depends on the handle of the fabric and its softness, suppleness,

fullness, etc.,

it improves the wearing qualities – Non soiling

it increase the weight of the fabric

it increases the sale value of the material

it improves the serviceability of the fabric

Hence, finishing is essential for a textile good before they are put on the market. There are

different types of finish but are applied on the fabric according to its end uses.

17. What is singeing? Explain it briefly?

Singeing is the process of removing the loose hairy fibres projecting from the surface

of the fabric by burning. There are done to give a smooth, even and clean looking face to the

fabric.

IMPORTANCE OF SINGEING:

The fabric should be singed because:

1. The fabric should be mercerized must be singed to develop maximum luster in the

fabric.

2. The fabric to be printed must be singed to import clearly defined and sharp

designs on the cloth.

So, the singeing is considered as important and essential process before mercerishing and

printing.

The main types of singing are,

hot plate singeing

roller singeing

gas singeing

Hot plate singeing:

It is the process of burning away the protruding or projection fibres, by passing the

fabric in full width form over the surface of the heated copper plates.

Roller singing:

Instead of using heated plates heated revolving rollers or hollow cylinders are used to

burn the protruding or projecting fibres.

Gas singeing:

It is the process of burning of protruding fibres by passing the fabric in between

flames of a gas burner. It is more economical, more conuenient and more efficient singeing.

Types of yarns to be singed:

Combed cotton yarns.

Sewing threads

High twisted voile threads

Polyester cotton blended yarns

Mosiery yarns meant for knitting

Types of fabrics should be singed:

Shirting, suiting, sarees, dress materials, voile cloths, poplins, polyester, cotton

blended fabric etc.,

WORKING OF GAS SINGEING MACHINE

GAS SINGEING MACHINE:

Gas singeing is more economical, more convenient and more efficient singeing. It is

mostly used in all processing mills in India. The machine of the following parts.

Guide Rollers

Drying cylinder

Brush roller

Burners

Water trough

Drag roller

Squeeze roller (and)

Steam chamber

Guide rollers:

The main function of guide rollers is to guide the fabric and also to give tension to the

fabric. The guide rollers after the burness are to extinguish any fire sparks present in the

fabric.

Dyeing Cylinder:

The main function of drying cylinder is to evaporate the moisture present in the

fabric. Sometimes more than one cylinder is used in this machine.

Brush Roller:

The main function of the brush roller is to raise the projecting fibres present in the

fabric.

Gas Burner’s:

The number of burners in a singeing unit may vary from 4 to 6. this burners are

arranged in both sides of the fabric which singed at a single passage. The flame is obtained by

burning a mixture of air and cool gas or air and petroleum. The intensity of the flame and its

distance from the fabric can be adjusted.

Water trough:

The object of the water through is to extinguish any fire spark present in the fabric.

Drag Roller:

The function of drag roller is to maintain the speed of the fabric.

Squeeze roller:

The function of the squeeze roller is to squeeze excess amount of water present in the

fabric.

Steam chamber (or) Quench box:

This chamber is filled with wet steam under low pressure. The water tap is sometimes

replaced by steam chamber. The function is to extinguish any fire span present in fabric.

Working :

The fabric from the guide roller is passed under the drying cylinder . It is to evaporate

the moister in the fabric with a help of guide roller , the fabric is comeing under the brush

roller, the fabric . It is to raise the projecting fibres from the surface of the fabric and passes

over and under the guide roller . During that stage over and under the guide roller . During

that stage , the fabric is passed in between their burners.

The burners are present as shown in the figure . the function of burners are present is

to burn the projecting fibres and their immediately the cloth is comeing to the water trough .

this is to extinguish any fire spark present in the fabric and then the fabric is passed in

between drag and squeeze roller and reaches the steam chamber . The

Purpose of steam chamber is to extinguish any fire mark without wetting the fabric. Finally,

we will get signed fabric. The speed of the cloth vary from 180 to 250yards % minutes.

Advantages of Gas singeing;

Both sides of a fabric can be singed at a single passage.

Their production is more because of high speed.

There is a possibility to maintain the temperature evenly throughout the fabric.

Fibers in the interstices are brunt

Different varieties of cloth can be singed.

Disadvantage Of Gas Singeing

When the flame is not controlled there is a chance of fire on the cloth.

Precaution in Gas singeing Machine:

The singeing machine must be kept separately from other machines.

The before singeing, the cloth should be died well.

Correct amount of heat should be given to the cloth. Otherwise, the cloth may be

tendered.

The speed of the cloth should be controlled properly

When stopping the machine, the flames are first extinguished and then the machine

will be stopped.

After singeing the cloth must be passed through water trough

The machine is enclosed with cover and exhaust fan otherwise the dust affecting the

eyes.

For observing, Glass, windows to be fitted on the nood.

18. What is shrinkage? Explain it briefly?

Shrinkage:

Shrinkage is the contraction in the dimension of the fabric due to usage. Cotton fabric

suffers from 2 main disadvantages of creasing and shrinkage during subsequent washing.

Creasing is overcome by the Resin finishing where as the shrinkage is prevented by a

special finishing known as sanforizing and the machine used for that purpose is known as

zero – zero pre shrinking machine.

How Cotton Shrinks:

Cotton has the property of swelling in water and this effects shrinking.

Also the weaving stress, strain and tension during spinning and weaving etc., when released

causes the fabric to shrink.

The cotton fabric when put in water swelling takes place and rearrangement of

internal forces takes place. The fibres will become free from tension and it comes to the

original tensionless state.

There are reasons the warp yarns are under much strain due to interlacement than the

weft yarns. Hence, when a fabric is allowed to shrink the warp your shrinkage will be more

than weft yarn.

To overcome this the fabric is extended in width wise to some extent in the stenter

machine during finishing process. Then it is subjected to the pure shrink process.

Mechanism:

The mechanism (or0 principle adopted to produce shrinkage is “to place the fabric on

the fabric on the extended surface of a rubber blanket represented by the concave surface.

When the tension is releared on the blanket, it shrinks, the fabric which is in close contact

with the rubber blanket at the concave surface has no way other than shrinking along with the

blanket”.

This principle is used to produce pre shrinking finish with the help of a sanforising

(or)Zero – Zero machine.

The amount or % of shrinkage depends on:

1. The tension / stretch on the rubber blanket

2. Thickness of the rubber blanket

3. Diameter of the roller

Generally three sizes are available:

Thickness of Blanket to be used If shrinkage of fabric before sanforising

is

0.275”

0.4”

0.45”

6-8 cm / m

8-11 cm / m

11-15 cm /m

The optimum moisture content of cotton and viscose fabric priors to compressive shrinkage

treatment in the machine must be 20-25% At lower moisture content different deformation of

the fabric may result. The deformation of the rubber blanket is 6-22% and the fabric

shrinkage is 3-4%. If the pressure exerted by the metal atm. Pressure, the rubber blanket is

deformed to 15% while the fabric shrinks

Machine Description:

This is a mechanical method of shrinkage control. The cloth is fed into the machine

through the feed rollers of a mangle. It is used to hold back the cloth and only allow the felt

blanket to contract to the required amount. Otherwise Over shrinking of the cloth occurs.

From the feed rollers the cloth passes between sprayers to moisten the cloth there by

making the yarn soft and plastic so that it can be easily compressed by the blanket.

The moistening is assisted by a steaming unit called skier. Then the cloth passed through a

short clip stender to control the width of the cloth.

The cloth is passed to the blanket over the feed roller and is placed in firm contact with the

stretched surface of the blanket by electrically heated shoes.

If main cylinder of the machine may be either 60” (or0 84” in diameter to the material for

which it is interned.

After passing a round of the drum of the palmer machine, the finished material may

be passed on to a auxiliary finisher.

It has an additional palmer unit.

It can be used

1. when both sides of the material are to be finished a like (or)

2. when additional shrinkage is required

if the additional palmer unit is used, the range is called as Duplex otherwise is called as

“Simplex”.

There is a blanket centering device to keep the blanket in a straight path on the

cylinder and also and indicator for giving the tension on the blanket.

The electrically heated shoes are lifted from the blanket automatically when the

machine is stopped to eliminate scorching. Before leaving the sanforiser, the fabric should be

thoroughly dried otherwise it will elongate.

Proper use of the sanforiser enables shrinkage on laundering. (Residual Shrinkage) to

be reduced to 0.75% or less.

After coming out of the felt calendaring unit the fabric is guided to the plater which

plaits the fabric in to trolley.

19.what is Reactive Dye? Explain Dyeing of cotton with Reactive cold brand Dyes?

Reactive Dyes:

The reactive dye originally reacts and form covalent bond with the fibre and hence

they are called as “Reactive Dyes”. Because of the strong covalent bond with the fibre, it has

good fastness properties.

Classification of Reactive Dyes:

Classification of reactive dyes :

1. Hot brand dyes – mono chloro tri azine dyes . These dyes have only one cl- group as

the reactive group which needs higher temperature to be available for reaction with

fibre . Hence they are called as HOT brand dyes .

2. Cold brand dyes – Di chloro Tri azine dyes . These dyes have two CL – groups and

hence they react with fiber even at room temperature . so they are called as cold brand

reactive dyes.

3. Vinyl sulphone dyes – Ramzol dyes.

4. Drimarine dyes – Ex….Levafix dyes

5. High Exhaustion dyes – HE dyes

6. Bi-functional dyes – ME dyes., FN dyes etc.,

Dyeing of cotton with reactive cold brand dyes

Dissolving the dyestuff

The dye is taken as per the shade% and pasted with a little quantity of wetting agent.

Then warm water is added and stirred.

Dyeing (Exhaust Method)

The dyeing procedure in winch dyeing machine is explained below. The fabric is loaded in

the cachine. The water is filled as per M:L ratio (1:20). The circulation of material is started.

5 min

Dye solution is added

5 min

½ of 30-50 gpl Sodium Chloride (Common salt) or 20-30 gpl Sodium Sulphate (Glabour salt)

is added as Exhausting agent It exhausts the dissolved dye from the solution and transfers the

same to the same to the substrate. (Refer mechanism of dyeing)

15 min

Remaining salt is added and the dyeing is continued.

45 min

10-20 gpl Sodium carbonate is added as fixing agent. This alkali enables the dye to form

covalent bond with the fibre.

30min – 60 min depending on shade

Hot wash at 50oC for 15 min

Cold washing 1% Acetic acid for 15 min

Hot soaping in 5 gpl soap and 1 gpl soda ash at 50oC for 15 min

Cold – washing for 15 min

20. Explain the mechanism of textiles finishes like glazing ,cireing andGigging on

fabrics?

FINISHING

Finishing is one of the essential processes of a processing mill where all bleached,

dyed and printed material are subjected before they are put on the market.

The aim of the textile finishing is to render textile goods fit for their end uses.

Finishing gives the following advantages:

1. Improved appearance – Lustre, Whiteness etc.,

2. Improved Feel which depends on the handle of the fabric and its Softness,

Suppleness, Fullness etc.,

3. It improves the wearing qualities – Non soiling, Anticrease.

4. It gives special properties required for particular uses – Water proofing , Flame

proofing etc.,

5. It covers the faults of the original cloth.

6. It increases the weight of the fabric.

7. It improves the sale value of the material.

8. It improves the natural attractiveness of the fabric.

9. It improves the serviceability of the fabric.

Hence, Finishing is essential for a textile good before they are put on the market.

TYPES OF FINISH

Finishing mainly falls into three groups;

1. Temporary Finish

2. Permanent Finish

3. Semi – Permanent Finish.

TEMPORARY FINISH

A finish which is not stable and goes off after the first wash is known as

TEMPORARY FINISH.

If the finishing effect in the fabric disappears during subsequent washing and usage

then it is called TEMPORARY FINISH.

Eg. Mechanical : Calendaring, Embossing etc.,

Chemical : Starching, Softening (Except Reactive softeners)

PERMANENT FINISH

If the finishing effect in the fabric does not appear and remains unaffected through all

the conditions of wear and washing treatments, then the finish is said to be a permanent

finish.

Eg., Mechanical : Sanforising, Mechanical milling of Wool etc.,

Chemical : Resin Finishing, Water proof, Flame proof finish etc.

Glazing

A stiff polished or glazed surface can be obtained by the application of starch, glue,

mucilage, or shellac followed by friction calendaring. The process makes a fabric resistant to

dust and spots and minimizes shrinkage. This finish is found principally on chintz. Vita-

Glaze is a typical trademark.

Cireing :

The cier process may be applied to silk , rayon , or nylon woven fabric usually satins

and taffetas – but may be also be used on knitted goods. Wax are another appropriate

compound is applied to the fabric, followed by hot calendaring. The result is a super gloss

almost metallic in appearance . ( A shiny surface given by a hot calendaring alone to a fabric

of a thermoplastic fiber is also called cire.

Gigging :

Wool fabrics may be napped ,or they may be subjected to a raising process called

gigging . when the fibers is first saturated with water . when the fibres of a rated with .when

the fibres of a moist wool fabric are raised, thay tend to curl and shrink . when brushed in one

direction a smooth and lustrus appreance result.

Tigering :

Fabric having a high ile or nap may be given a tingering finish to lift and comb the

nap so as to improve or modify , its height and remove loose fibres. The tiger roll has long

fine wires then penetrate to the ground of the fabric to lift up the fibres not raised by the

napper rolls. The effectiveness is dependent upon the wires , their nature of their hooks.

Tigering may be done to such be done such fabrics as velour ,limitations and imitations fiber