Upload
vuongcong
View
219
Download
0
Embed Size (px)
Citation preview
11512 SPACE CENTER BLVD, HOUSTON TEXAS 77059 P +1 281 990 8582 F +1 281 990 8644
WWW.FLOWTREND.COM
Flowtrend® is the manufacturer of these products. Flowtrend® is not sponsored by, affiliated with, connected with, and does not represent or otherwise have any endorsement from any other manufacturer included to or referred to in this document. Any name, model, part number, brand, image, material, or referral is for descriptive purposes only and is not intended to suggest any affiliation, connection or sponsorship from any other manufacturer. Tri-Clover® is a Registered Trademark of Alfa Laval, Inc. Viton® and Buna® are Registered Trademarks of DuPont Performance Elastomers L.L.C.
Flowtrend Replacement for the Tri-Clover® 361 Seat Valve
• Air-operated seat valve featuring
the positive action of a short-stroke
actuator with heavy-duty clamps and
precision-molded bonnet gaskets
• Remote controlled by compressed air
• Sanitary, flexible design can be used
as a stop valve with 2 – 3 ports or as a
divert valve with 3 – 5 ports
• Simple moveable parts mean reliability
• Intended to be interchangable with
OEM.
Suitable For
High-volume sanitary liquid processing systems where correct alignment of a clean-
in-place valve must be maintained under severe operating conditions.
Features
• Open yoke with visible valve
stem coupler
• Single O-ring stem design, allows
o-ring and stem groove to be cleaned
and sanitized
• Valve porting is flush with the bottom
surface to ensure full drainage of the
valve body
• Highly polished wetted areas
eliminate crevices that can trap and
harbor bacteria
• Operates in temperatures of
up to 285 ° (EPDM)
• Repairable actuator
• Standard stock item
Materials
Product wetted steel surfaces: Stainless steel AISI 316L
Finish: 32 Ra Standard ID
Plug stem: LP bonded Buna® or “TR” (PTFE replaceable)
Product wetted seals: NBR
Other seals: Buna
Product connections: Clamp and Butt Weld
Specifications
ACTUATOR FUNCTIONS• Pneumatic downward movement,
spring return (NO)
• Pneumatic upward movement, spring
return (NC)
AIR SUPPLY• Air pressure range for sizes 1" – 3" is 35
to 50 psi (normal)
• Air volume requirements, sizes 1" – 3"
is 16 cubic inches
• Actuator can handle air supply
pressure greater than 50 psi to close
against higher line pressures
FLOWTREND 361-R SEAT VALVES
Body Styles: 10, 30, 21, 23, 41 and 43
by, affiliated with, connected with, and does not represent or otherwise have any
endorsement from any OEM manufacturer listed below. Any name, model, part
number, brand, image, material or referrals for descriptive purposes only. ALFA
LAVAL®, AMPCO®, APV, BALDOR®, BURKERT®, DEFINOX®, FRISTAM®, GAMA JET ®,
JUNG®, LC THOMSEN®, SINE®, SUDMO®, TOFTEJORG®, TRI-CLOVER®, TUCHENHAGEN®
and WAUKESHA®.
11512 Space Center Blvd, Houston Texas 77059 P +1 281 990 8582 F +1 281 990 8644
WWW.FLOWTREND.COM
Flowtrend® 361-R Seat Valve is a Flowtrendmanufactured replacement for the Tri-Clover® 361 seat valve. Flowtrend’s parts and products are not Alfa Laval® parts and products, and Alfa Laval® does not endorse, approve or warrant Flowtrend’s parts orproducts, or their use.
11512 Space Center Blvd, Houston Texas 77059P +1 281 990 8582 F +1 281 990 8644
WWW.FLOWTREND.COM
Flowtrend® is the manufacturer of these products. Flowtrend® is not sponsored by, affiliated with, connected with, and does not represent or otherwise have any endorsement from any other manufacturer included to or referred to in this document. Any name, model, part number, brand, image, material, or referral is for descriptive purposes only and is not intended to suggest any affiliation, connection or sponsorship from any other manufacturer. Tri-Clover® is a Registered Trademark of Alfa Laval, Inc. Viton® and Buna® are Registered Trademarks of DuPont Performance Elastomers L.L.C.
AIR LOADINGThe additional air supply pressure needed to hold each additional 10 psi of product
line pressure for Model 20 is:
1 ½" : 1.0 psi
2" : 2.0 psi
2 ½" : 3.0 psi
3" : 4.5 psi
Dimensions
Dimensions for all Flowtrend 361-R Shut-Off/Divert valves with standard actuators
are shown.
FT 361-10 FT 361-30 FT 361-21
FT 361-23 FT 361-41 FT 361-43
FLOWTREND 361-R SHUT-OFF & DIVERT VALVES
VALVE SIZEA B
CShut-Off Valves Divert Valves Divert Valves
in mm in mm in mm in mm in mm
1.5 38 14.10 358 17.99 457 3.35 85 2.76 70
2 51 15.04 382 19.49 495 3.78 96 3.50 89
2.5 63.5 15.28 388 20.24 514 4.21 107 3.47 88
3 76 15.91 404 21.26 540 4.76 121 3.78 96
Options• Pneumatic upward and downward
movement (A/A)
• Actuator for intermediate position of
the valve plug
• Seals and gaskets of EPDM or FPM/
FKM
• LP Bonded stem plug of EPDM or
FPM/FKM
• Bonded stainless steel gasket
©2018 Flowtrend
FLOWTREND 361-R SEAT VALVES
Body Styles: 10, 30, 21, 23, 41 and 43
Flowtrend® is manufacturer of the OEM replacement parts. Flowtrend® is sponsored
by, affiliated with, connected with, and does not represent or otherwise have any
endorsement from any OEM manufacturer listed below. Any name, model, part
number, brand, image, material or referrals for descriptive purposes only. ALFA
LAVAL®, AMPCO®, APV, BALDOR®, BURKERT®, DEFINOX®, FRISTAM®, GAMA JET®,
JUNG®, LC THOMSEN®, SINE®, SUDMO®, TOFTEJORG®, TRI-CLOVER®, TUCHENHAGEN®
and WAUKESHA®.
11512 Space Center Blvd, Houston Texas 77059
Flowtrend 361-R Seat Valve_40918
Flowtrend® 361-R Seat Valve is a Flowtrend manufactured replacement for the Tri-Clover® 361 seat valve. Flowtrend’s parts and products are not Alfa Laval® parts and products, and Alfa Laval® does not endorse, approve or warrant Flowtrend’s parts or products, or their use.
11512 Space Center Blvd, Houston Texas 77059 P +1 281 990 8582 F +1 281 990 8644
WWW.FLOWTREND.COM
FLOWTREND 361-10-R FLOWTREND 361-30-R FLOWTREND 361-21-R
FLOWTREND 361-23-R FLOWTREND 361-41-R FLOWTREND 361-43-R