Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
CP001D/06/en/03.1071024143INDD CS2
Flow measurementSelection guide
Instruments International
Endress+HauserInstruments International AGKaegenstrasse 24153 ReinachSwitzerlandTel. +41 61 715 81 00Fax +41 61 715 25 00http://[email protected]
Combinable with
Accuracy (best possible accuracy)
10Basic
SensorD, L, W, P, H ±0.5%
50Standard
Sensor D, L, W, P, H
±0.5% Optional: ±0.2%
53High-end
Sensor W, P, H ±0.2%
51Custody transfer
Sensor W, P
±0.5% Optional: ±0.2%
23Two-wire
Sensor P, H ±0.5%
55Special applications
Sensor S, H ±0.2%
91 Basic
Sensor W
Onsite: <2.0% Under reference conditions: ±0.5%
93 High-end
Sensor W, P, C
Onsite: <2.0% Under reference conditions: ±0.5%
92 F Inline
Sensor F
Liquids For 2 or 3 beams: ±0.5%
For 4 beams: ±0.3%
93 T Portable
Sensor P
Onsite: <2.0% Under reference conditions: ±0.5%
Deltabar SPMD 70/75 Deltatop
Orifice plate DO: ±0.5 to 0.8%Pitot tube DP: ±1.0%
Nozzle DN: ±0.7 to 1.0%Venturi tube DV: ±0.7 to 1.0%
Deltabar MPMD 70/75 Deltatop
Orifice plate DO: ±0.5 to 0.8%Pitot tube DP: ±1.0%
Nozzle DN: ±0.7 to 1.0%Venturi tube DV: ±0.7 to 1.0%
Diameter
Elec
trom
agne
tic (
EMF)
Prol
ine
Prom
ag
Promag DWater/Waste water
DN 25 to 100 (1" to 4")
Promag LWater/Waste water
DN 50 to 300 (2" to 12")
Promag WWater/Waste water
DN 25 to 2200 (1" to 88")
Promag PChemical/Process applications
DN 15 to 600 (½" to 24")
Promag HHygiene
DN 2 to 100 (1/12" to 4")
Promag S Inhomogeneous fluidsHigh solid content
DN 15 to 600 (½" to 24")
Ultr
ason
ic
Prol
ine
Pros
onic
Flo
w
Prosonic Flow WClamp-on sensor Standard applications
DN 50 to 4000 (2" to 156")
Prosonic Flow WInsertion sensor Standard applications
DN 200 to 4000 (8" to 156")
Prosonic Flow PClamp-on sensor Process applications
DN 15 to 4000 (½" to 156")
Prosonic Flow CInline sensor Water/Waste water
DN 300 to 2000 (12" to 78")
Prosonic Flow FInline sensorTwo-wire technology
DN 25 to 150(1" to 6")
Diff
eren
tial p
ress
ure
Deltatop DOOrifice plate
DN 10 to 1000 (3/8" to 40")
Deltatop DPPitot tube
DN 40 to 12,000 (1½" to 480")
Deltatop DNNozzle
DN 50 to 500 (2" to 20")
Deltatop DVVenturi tube
DN 50 to 2000 (2" to 78")
Requirements Fluids (examples) Measuring principle
Elec
tro-
m
agne
tic
Cor
iolis
Ultr
ason
ic
Vort
ex
Ther
mal
Diff
eren
tial
pres
sure
Liqu
ids
Liquids in general Water • • • • •Flow rates < 2 l/h Additives, flavors • •Non-conductive liquids Oil, hydrocarbons • • • •Viscous liquids > 500 mPa�s Molasse, shower gel • •Cryogenic fluids Liquid O2 , Ar, N2 • • •Volume flow Water, milk, solvents • • • • •Mass flow Chemicals • • •Accuracy ≤ 0.2% • •Nominal pipe diameter DN > 500 • • •Operable flow range > 1:30 • • •Low pressure loss • • •Density, concentration, viscosity metering Foods, shower gel •Process temperature > 200 °C • • •
How to use this selection guide
Selecting the measuring principle
Define all the primary requirements for your measuring point: fluid type, nominal diameter, accuracy, pressure, temperature, etc.
In the table on Page 4, select the category for the type of fluid in question: Liquid – Gas – Steam – Special applications.
In the table, specify all the requirements (see Point )
you defined for your measuring point.
Now select the measuring principles to which all the
requirements apply (•).
Selecting the flowmeter
Now open out this brochure completely. The overview contains all the measuring principles you selected under Point and the corresponding Endress+Hauser flowmeters.
Now mark the sensors that can be installed in the pipe of your choice (DN = 1600 mm).
Mark those transmitters that can be combined with the
sensors in question and that meet the required accuracy specifications (<0.3% o.r.)
You have found the two flowmeters that suit your measuring point.
• Electromagnetic• Ultrasonic• Differential pressure
• Promag W• Prosonic Flow W (clamp-on)• Prosonic Flow W (insertion)• Prosonic Flow P• Prosonic Flow C• Deltatop DP• Deltatop DV
• 50 (W)• 53 (W)
• Promag 50W (standard)• Promag 53W (high-end)
Example
• Fluid: drinking water (urban area)• Pipe diameter: DN 1600• Required accuracy: <0.3% o.r.• Measured variable: Volume flow • Liquids
• Liquids in general • Volume flow• Nominal diameter DN > 500
• Electromagnetic• Ultrasonic• Differential pressure
➊
➋
➌
➍
➎
➏
➐
➑
➊
➍
2 3
➋ ➌ ➍
➎ ➏➑
Promag WWater/Waste water
➐ ➐➑
53High-end
50Standard
Requirements Fluids (examples) Measuring principle
Elec
tro-
m
agne
tic
Cor
iolis
Ultr
ason
ic
Vort
ex
Ther
mal
Diff
eren
tial
pres
sure
Liqu
ids
Liquids in general Water • • • • •Flow rates < 2 l/h Additives, flavors • •Non-conductive liquids Oil, hydrocarbons • • • •Viscous liquids > 500 mPa�s Molasse, shower gel • •Cryogenic fluids Liquid O2 , Ar, N2 • • •Volume flow Water, milk, solvents • • • • •Mass flow Chemicals • • •Accuracy ≤ 0.2% • •Nominal pipe diameter DN > 500 • • •Operable flow range > 1:30 • • •Low pressure loss • • •Density, concentration, viscosity metering Foods, shower gel •Process temperature > 200 °C • • •Process pressure > 100 bar Crude oil • • • •
Gas
Gas flow in general Natural gas, air • • • •Contaminated gas Biogas, exhaust gas • • •Volume flow Exhaust gas • •Mass flow CO2 • • • •Accuracy ≤ 0.5% Rare gas •Nominal pipe diameter DN > 300 • •Operable flow range > 1:30 • •Low pressure loss Air • •Process temperature > 200 °C Exhaust gas • •Process pressure > 100 bar CNG • • •
Stea
m
Volume flow • •Mass flow • •Nominal pipe diameter DN > 300 •Operable flow range > 1:10 •Low pressure loss •Process temperature > 300 °C Superheated steam • •Process pressure > 100 bar Superheated steam • •
Spec
ial
appl
icat
ions
Hygienic applications (SIP/CIP) Milk, beer • • •Slurries, suspended solids Thick sludge • •Liquid/liquid mixtures Oil/water, emulsions •Highly abrasive fluids (e.g. in mining) Ore slurry •Bidirectional metering (forward/reverse) • • • •Measurement from outside without process interruption/retrofitting/temporary metering •
Filling/bottling applicationsGas refueling applications
see Flow measurement OEM (inside)
Flow monitoring see Flow monitoring (inside)
Selection table “Measuring principles”
Please note:The selection table above provides a general overview and is used for quick clarification of suitable measuring principles. The table is not exhaustive. If further clarification is required, feel free to contact Endress+Hauser any time. We’ll be glad to be of assistance.
Supplementary documentation
4 5
Flow measurement For liquids, gases and steam
Products and services at a glance
FA005D/06/en(Order number 71024542)
Metering flow the cost- optimised way
Comprehensive metering point solutions for planning, commissio-ning and maintenance
CP006D/06/en(Order number 50109047)
Flow measurement in utilities
Energy management in your hands –customized solutions for compressed air, gas, steam and water
CP007D/06/en(Order number 71009419)
Flow handbook
A practical guide: Measurement technologies – applications – solutions
ISBN 3-9520220-4-7(Order number 50104766)
Precision for the real worldOur calibration facilities at your service
We calibrate your flowmeters on the world’s most advanced rigs – in our factory or onsite
CP010D/06/en(Order number 71091218)
Reduce energy costs
Tailor-made energy monitoring –rapid return on investmentFor steam, air, gas, oil, water, electricity, heating and cooling
CP014D/06/en(Order number 71109850)
Project documentation – data collection, archival, exportThe use of additional expansion mod-ules permits cost-saving administration and documentation of data for entire plant projects:• Clear presentation in a tree structure
of any desired number of metering points (e.g. by building, floor, meter-ing point), according to ISA 88.
• Uncomplicated inclusion of measur-ing devices directly from the Selection and Sizing functions. Also possible for instruments from other manufactur-ers or projects.
• Detailed listing of project manage-ment data (responsible person, cost-ing and budget data, etc.)
• Multiple data exchange possibilities in Excel or XML format: data export to other programs, data import from other projects, etc.
Applicator® • Optimal planning and
sizing of flowmeters• Administration and
documentation for entire plant projects
FieldCare® • Easy and dependable commissioning and
configuring of measuring devices via PC• Complete documentation of device settings• Storing device data (upload/download)• Simplified trouble-shooting
• Process-optimization through the visualization of measurement data in realtime (line plotting function)
• Analysis of diagnostic data for maintenance purposes• Administration and analysis of verification results
from the “Fieldcheck” test instrument
Fieldcheck® • Simulation and
testing of alarm/process conditions directly in the plant (without flow)
• Verification of flow-meters directly in the piping (without removal)
W@MApplicator ® – Optimal planning and sizingThe first steps are always the most important when it comes to planning metering points: An optimally dimensioned flowmeter at the right location provides many advantages. • Consistent process quality• Product savings due to error-free, precise measurement• Diminished risk of instrument failure at a later time
Proven over 20 years of useApplicator is a software for selecting and specifing flow- meters that has proven its abilities over many years. A wealth of industry experience and specialized know-how is embed-ded in Applicator. It enables people with limited technical knowledge to specify metering points quickly and easily.
The most recent version of Applicator has a raft of new features, including selection functions for all the other areas covered by Endress+Hauser – namely level, pressure, temperature, liquid analysis, etc. You’ll find that it opens up an enormous range of application possibilities in metrology and control.
Selection – straight to your objectiveWhen starting out to select the ideal flowmeter, Appli-cator guides you through all the important parameters. Just enter the type of fluid, required process data or metering point attributes and Applicator already displays the measuring principles and families of meters best suited to the case in hand.The Selection Tool contains over 600 products from all of the Endress+Hauser fields of operation.
Sizing – safe specificationBy entering further application-specific values, such as process pressure, process temperature or measuring range, Applicator immediately determines the ideal flowmeter type – and along with the suitable nomi-nal diameter, working range, pressure loss, accuracy, material loads, conformity with the Pressure Equipment Directives (PED) and corrosion resistance. Messages and warnings make it easy to select the right meter, help avoid common mistakes, and enable optimi-zation of the measuring point to suit specific require-ments. Additional Sizing Tools exist for level, pressure and energy measuring devices.
6 7
W@M – Life cycle management from Endress+ Hauser is an information system which provides tech-nical and operative management with complete data flow and archival – from commissioning on through
to maintenance and service within a plant, at any time or location. W@M is an open system based on Inter-net/intranet technology, and incorporating all software programs, products and services from Endress+Hauser.
Diameter Measuring range Pressure PN Processtemperature
Materials(wetted parts)
Process connection Protection Hygienic certification
Elec
trom
agne
tic (
EMF)
Prol
ine
Prom
ag
Promag DWater/Waste water
DN 25 to 100 (1" to 4")
0 to 10 m/s 0 to 600 m³/h
PN 16 Cl 150JIS 10 K
0 to +60 °C Polyamide liner Wafer: DIN, ANSI, JIS IP67 (NEMA 4X) –
Promag LWater/Waste water
DN 50 to 300 (2" to 12")
0 to 10 m/s 0 to 2400 m³/h
PN 10 to 16 Cl 150 –20 to +90 °C Polyurethane liner
PTFE liner Lap-joint flanges: DIN, ANSI IP67/IP68 (NEMA 4X/6P) –
Promag WWater/Waste water
DN 25 to 2200 (1" to 88")
0 to 10 m/s 0 to 136,000 m³/h
PN 6 to 40, Cl 150 to 300 JIS 10 to 20 K AWWA Class D
AS Table E, PN 16
–20 to +80 °C Hard rubber liner Polyurethane liner Flange: DIN, ANSI, JIS, AWWA, AS IP67/IP68
(NEMA 4X/6P) –
Promag PChemical/Process applications
DN 15 to 600 (½" to 24")
0 to 10 m/s 0 to 9600 m³/h
PN 10 to 40 Cl 150 to 300 JIS 10 to 20 K
AS Table E, PN 16
–40 to +180 °C PFA liner PTFE liner Flange: DIN, ANSI, JIS, AS IP67/IP68
(NEMA 4X/6P) –
Promag HHygiene
DN 2 to 100 (1/12" to 4")
0 to 10 m/s 0 to 282 m³/h
PN 16 to 40 Cl 150
JIS 10 to 20 K–20 to +150 °C PFA liner
Flange: DIN, ANSI, JIS, external thread, internal thread,
weld connection, clamp connection, couplings
IP67 (NEMA 4X) 3-A, EHEDG
Promag S Inhomogeneous fluidsHigh solid content
DN 15 to 600 (½" to 24")
0 to 10 m/s 0 to 9600 m³/h
PN 10 to 40 Cl 150 to 300 JIS 10 to 20 K
AS Table E, PN 16
–40 to +180 °CPTFE, PFA, polyurethane,
natural rubber liner,hard rubber liner
Flange: DIN, ANSI, JIS, AS IP67/IP68 (NEMA 4X/6P) –
Cor
iolis
Prol
ine
Prom
ass
Promass FUniversal flowmeter
DN 8 to 250 (3/8" to 10")
DN 25, 50, 80 (HT)0 to 2,200,000 kg/h
PN 16 to 100 Cl 150 to 600 JIS 10 to 63 K
–50 to +200 °C –50 to +350 °C (HT)
904L (1.4539)/ 316L (1.4404)
Alloy C-22 (2.4602)
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings, VCO
IP67 (NEMA 4X) 3-A, EHEDG
Promass MHigh pressure
DN 8 to 80 (3/8" to 3")
DN 8 to 25 (HP)0 to 180,000 kg/h
PN 40 to 100, PN 350 (HP) Cl 150 to 600 JIS 10 to 63 K
–50 to +150 °C DN 8...50: Titanium grade 9DN 80: Titanium grade 2
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings
IP67 (NEMA 4X) 3-A
Promass ALow flow rates
DN 1 to 4(1/24" to 5/32") 0 to 450 kg/h
PN 16 to 400 Cl 150 to 600 JIS 10 to 63 K
–50 to +200 °C 904L (1.4539) Alloy C-22 (2.4602) Tri-Clamp, VCO IP67
(NEMA 4X) 3-A, EHEDG
Promass IHygiene, viscosity
DN 8 to 80 (3/8" to 3") 0 to 180,000 kg/h
PN 40 to 100 Cl 150 to 600 JIS 10 to 63 K
–50 to +150 °C Measuring tube: Titanium grade 9Flange: Titanium grade 2
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings
IP67 (NEMA 4X) 3-A, EHEDG
Promass HChemically aggressive fluids
DN 8 to 50 (3/8" to 2") 0 to 70,000 kg/h
PN 40 Cl 150 to 300 JIS 10 to 20 K
–50 to +200 °C Zirconium 702/R 60702 Flange: DIN, ANSI, JIS IP67
(NEMA 4X) –
Promass EBasic applications
DN 8 to 80 (3/8" to 3") 0 to 70,000 kg/h
PN 40 to 100 Cl 150 to 600 JIS 10 to 63 K
–40 to +140 °C 904L (1.4539)316L (1.4404)
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings, VCO
IP67 (NEMA 4X) –
Promass ETwo-wire Basic applications
DN 8 to 50 (3/8" to 2") 0 to 70,000 kg/h
PN 40 to 100 Cl 150 to 600 JIS 10 to 63 K
–40 to +140 °C 904L (1.4539)316L (1.4404)
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings, VCO
IP66/IP67 (NEMA 4X) –
Promass S Food & Beverages
DN 8 to 50 (3/8" to 2") 0 to 70,000 kg/h
PN 40 to 63 Cl 150 to 300 JIS 10 to 40 K
–50 to +150 °C 904L (1.4539)316L (1.4435)
Flange: DIN, ANSI, JIS, Tri-Clamp, couplings
IP67 (NEMA 4X) 3-A, EHEDG
Promass PLife Sciences Industries(Pharma, biotechnology)
DN 8 to 50 (3/8" to 2") 0 to 70,000 kg/h
PN 40 to 63 Cl 150 to 300 JIS 20 to 40 K
–50 to +200 °C 316L (1.4435)Flange: DIN, ANSI, JIS,
Hygienic clamps, couplings and flanges
IP67 (NEMA 4X)
3-A, EHEDG,ASME BPE
Ultr
ason
ic
Prol
ine
Pros
onic
Flo
w
Prosonic Flow WClamp-on sensor Standard applications
DN 50 to 4000 (2" to 156")
0 to 15 m/s 0 to 678,550 m³/h
No limit Non-invasive –20 to +80 °C not wetted
(Clamp-on sensor) Clamp-on sensor IP67/IP68 (NEMA 4X/6P) –
Prosonic Flow WInsertion sensor Standard applications
DN 200 to 4000 (8" to 156")
0 to 15 m/s 0 to 678,550 m³/h PN 16 –20 to +80 °C 316L (1.4404) Welding connector IP68
(NEMA 6P) –
Prosonic Flow PClamp-on sensor Process applications
DN 15 to 4000 (½" to 156")
0 to 15 m/s 0 to 678,550 m³/h
No limit Non-invasive –40 to +170 °C not wetted
(Clamp-on sensor) Clamp-on sensor IP67/IP68 (NEMA 4X/6P) –
Prosonic Flow CInline sensor Water/Waste water
DN 300 to 2000 (12" to 78")
0 to 10 m/s 0 to 47,400 m³/h
PN 16 CI 150 –20 to +60 °C Carbon steel, epoxy coated Flange: DIN, ANSI, AWWA IP68
(NEMA 6P) –
Prosonic Flow FInline sensorTwo-wire
DN 25 to 150(1" to 6")
0 to 10 m/s 0 to 600 m³/h
PN 40CI 300 –40 to +150 °C
Meter body: CF3M (1.4404)Sensor: 316/316L (1.4404)
Flange: F316/F316L (1.4404)Flange: DIN, ANSI, JIS IP67/IP68
(NEMA 4X/6P) –
Vort
ex
Prol
ine
Prow
irl
Prowirl FFlanged version
DN 15 to 300 (½" to 12")
Liquids: 0.16 to 2360 m³/h Gases: 3 to 19,700 m³/h
PN 10 to 250 Cl 150 to 1500 JIS 10 to 40 K
–200 to +400 °COptional:
–200 to +450 °C
Meter body: CF3M (1.4404),Alloy C-22 (2.4602)
DSC sensor: 316L (1.4435), Inconel 718, Alloy C-22 (2.4602)
Flange: DIN, ANSI, JISOptional: with integrated reduction
of line size
IP67 (NEMA 4X) –
Prowirl WWafer version
DN 15 to 150 (½" to 6")
Liquids: 0.19 to 625 m³/h Gases: 4 to 5210 m³/h
PN 10 to 40 Cl 150 to 300 JIS 10 to 20 K
–200 to +400 °COptional:
–200 to +450 °C
Meter body: CF3M (1.4404)DSC sensor: 316L (1.4435) Wafer: DIN, ANSI, JIS IP67
(NEMA 4X) –
Ther
mal
Prol
ine
t-m
ass t-mass I
Insertion sensor DN 80 to 1500
(3" to 60") Gases: 0 to 120 m/s 290 psi g20 bar rel. –40 to +130 °C 316L (1.4404)
Alloy C-22 Thread: NPT, G1A IP67 –
t-mass FFlanged version
DN 15 to 100 (½" to 4") Gases: 0 to 120 m/s PN 16 to 40
Cl 150 to 300 –40 to +100 °C 316L (1.4404) Alloy C-22 Flange: DIN, ANSI, JIS IP67 –
Diff
eren
tial p
ress
ure
Deltatop DOOrifice plate
DN 10 to 1000 (3/8" to 40")
Liquids: 0 to 12 m/s Gases: 0 to 65 m/s Steam: 0 to 65 m/s
PN 6 to 420 Cl 150 to 2500 –200 to +1000 °C
C22.8 316Ti (1.4571)
15Mo3 (1.5415)
Wafer (corner tapping) Flange (flange tapping) Pipe unit (meter run)
IP68 (NEMA 6P) –
Deltatop DPPitot tube
DN 40 to 12,000 (1½" to 480")
Liquids: 0 to 12 m/s Gases: 0 to 65 m/s Steam: 0 to 65 m/s
PN 6 to 420 Cl 150 to 2500 –200 to +1000 °C C22.8
316Ti (1.4571)Cutting ring,
flange, flow tapIP68
(NEMA 6P) –
Deltatop DNNozzle
DN 50 to 500 (2" to 20")
Liquids: 0 to 12 m/s Gases: 0 to 65 m/s Steam: 0 to 65 m/s
PN 6 to 420 Cl 150 to 2500 –200 to +1000 °C
e.g. C22.8316Ti (1.4571)
15Mo3 (1.5415)13CrMo45
Flange: DIN, ANSI, JISWafer: DIN, ANSI, JIS
Butt-weld version
IP68 (NEMA 6P) –
Deltatop DVVenturi tube
DN 50 to 2000 (2" to 78")
Liquids: 0 to 12 m/s Gases: 0 to 65 m/s Steam: 0 to 65 m/s
PN 6 to 420 Cl 150 to 2500 –200 to +1000 °C
e.g. C22.8316Ti (1.4571)
15Mo3 (1.5415)13CrMo45
Flange: DIN, ANSI, JISWafer: DIN, ANSI, JIS
Butt-weld version
IP68 (NEMA 6P) –
EMF Dosimag
Filling/bottlingConductive liquids
DN 4, DN 8, DN 15K, DN 15
(5/32", 3/8", ½")
0 to 10 m/s0 to 1.66 l/s PN 16 –40 to +130 °C PFA liner Tri-Clamp, weld connection IP67
(NEMA 4X) 3-A, EHEDG
Cor
iolis
DosimassFilling/bottlingLiquids
DN 8, DN 15, DN 25
(3/8", ½", 1")
0 to 5 kg/s PN 40 –40 to +125 °C 904L (1.4539)316L (1.4404) Tri-Clamp, couplings IP67
(NEMA 4X) 3-A
CNGmassFuelingCompressed Natural Gas
DN 8, DN 15, DN 25
(3/8", ½", 1")0 to 150 kg/min max. 350 bar –50 to +125 °C 316L (1.4404)
316L (1.4435)
Internal thread: G½" (DN 8)G¾" (DN 15)G1" (DN 25)
IP67(NEMA 4X) –
CNGmass DCIFuelingCompressed Natural Gas
DN 8, DN 15, DN 25
(3/8", ½", 1")0 to 150 kg/min max. 350 bar –50 to +150 °C 316L (1.4404)
316L (1.4435)
Internal thread: G½" (DN 8)G¾" (DN 15)G1" (DN 25)
IP67(NEMA 4X) –
LPGmass FuelingLiquified Petroleum Gas
DN 8, DN 15, DN 25, DN 40
(3/8", ½", 1", 1½")0 to 70,000 kg/h
PN 40 Cl 150 to 300 JIS 10 to 63 K
–40 to +125 °C 316L (1.4404)904L (1.4539)
Flange: DIN, ANSI, JIS, VCO
IP67(NEMA 4X) –
CubemassLow flow rates
DN 1, DN 2, DN 4, DN 6
(1/24", 1/12", 5/32", ¼")0 to 1000 kg/h 160/400 bar –50 to +200 °C 904L (1.4539) VCO IP67
(NEMA 4X) –
Cubemass DCILow flow rates
DN 1, DN 2, DN 4, DN 6
(1/24", 1/12", 5/32", ¼")0 to 1000 kg/h 160/400 bar –50 to +200 °C 904L (1.4539) VCO IP67
(NEMA 4X) –
EMF Magphant
Limit switch/Trend displayConductive liquids
DN 1 to 2000(½" to 78") 0 to 5 m/s PN 16 –20 to +120 °C PVDF Weld nipple IP66
(NEMA 4X) –
Ther
mal
Flowphant DTT31Standard applicationsLiquids
DN 20 to 1000(3/4" to 40")
0.03 to 3 m/s as a relative value between
0 and 100%max. PN 100 –20 to +85 °C AISI 316L Weld nipple, compression fitting,
threaded connection: ANSI, ISO IP64 –
Flowphant DTT35Hygienic applications Liquids
DN 20 to 1000(3/4" to 40")
0.03 to 3 m/s as a relative value between
0 and 100%max. PN 100 –20 to +85 °C AISI 316L and FKM Viton,
EPDM (sealings)Conical metal-metal G½",
Tri-Clamp IP64 3-A
t-switch ATT11Limit switch Liquids, gases
DN 40 to 1000 (1½" to 40")
Liquids: 0 to 3 m/s Gases: 0 to 50 Nm/s PN 25 –10 to +80 °C 316L (1.4404/1.4435) Threaded connection: BSP, NPT,
couplings, Tri-ClampIP66
(NEMA 4X) –
t-trend ATT12Trend display Liquids, gases
DN 40 to 1000 (1½" to 40")
Liquids: 0 to 3 m/s Gases: 0 to 50 Nm/s PN 25 –10 to +80 °C 316L (1.4404/1.4435) Threaded connection: BSP, NPT,
couplings, Tri-ClampIP66
(NEMA 4X) –
Combinable with
Housings Display/Operation Ambienttemperature
Power supply Galvanic isolation Inputs Outputs Communication Accuracy (best possible accuracy)
Ex-approvals Protection
10Basic
SensorD, L, W, P, H
Compact AluRemote Alu
Two-line LCD/ push buttons
Operation via FieldCare–20 to +60 °C 85 to 250 V AC (45 to 65 Hz)
20 to 28 V AC (45 to 65 Hz) or 11 to 40 V DCElectronical connections are
galvanically isolated from each other – 4 to 20 mA, pulse/status HART® ±0.5% FM, CSA Div. 2 IP67 (NEMA 4X)
50Standard
Sensor D, L, W, P, H
Compact SSCompact AluRemote Alu
Two-line, backlit LCD/ push buttons
Operation via FieldCare
–20 to +60 °COptional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other Status 0/4 to 20 mA, pulse/frequency
(1 kHz passive), statusHART®, PROFIBUS PA,
PROFIBUS DP±0.5%
Optional: ±0.2% ATEX, IEC, FM, CSA, TIIS, NEPSI IP67 (NEMA 4X)
53High-end
Sensor W, P, H
Compact SSCompact AluRemote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare
–20 to +60 °C Optional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other
Status, current input
0/4 to 20 mA, pulse/frequency (10 kHz, active/passive), relays, status
HART®, PROFIBUS PA, PROFIBUS DP, FOUNDATION
Fieldbus, MODBUS® RS485±0.2% ATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
51Custody transfer
Sensor W, P
Compact AluRemote Alu
Two-line, backlit LCD/ push buttons
Operation via FieldCare–20 to +60 °C 85 to 260 V AC (45 to 65 Hz)
20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DCElectronical connections are
galvanically isolated from each other Status 0/4 to 20 mA, pulse/frequency (1 kHz passive), status HART® ±0.5%
Optional: ±0.2% ATEX, IEC IP67 (NEMA 4X)
23Two-wire
Sensor P, H Compact Alu
Four-line LCD/ touch control
Operation via FieldCare–20 to +60 °C
Two-wire12 to 30 V DC
13.9 to 30 V DC (Ex) (45 to 65 Hz)
Electronical connections are galvanically isolated from each other – 4 to 20 mA,
pulse/frequency, status HART® ±0.5% ATEX, FM, CSA IP67 (NEMA 4X)
55Special applications
Sensor S, H
Compact SS Compact AluRemote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare
–20 to +50 °COptional: –40 to +50 °C 20 to 260 V AC/DC (45 to 65 Hz) Electronical connections are
galvanically isolated from each otherStatus,
current input0/4 to 20 mA, pulse/frequency
(10 kHz, active/passive), relays, status
HART®, PROFIBUS PA, PROFIBUS DP,
FOUNDATION Fieldbus±0.2%
FM, CSA Div. 2 In preparation: ATEX II 3G,
IEC Zone 2
IP67 (NEMA 4X)
40 Basic
SensorE Compact Alu
Two-line, backlit LCD/ Operation via HART® resp.
FieldCare
–20 to +60 °C Optional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other Status 0/4 to 20 mA, frequency, status HART® Liquids: ±0.5%
Gases: ±1.0% ATEX, IEC, FM, CSA, TIIS, NEPSI IP67 (NEMA 4X)
80 Standard
Sensor F, M, A, I, H, E, S, P
Compact SSCompact AluRemote Alu
Two-line, backlit LCD/ push buttons
Operation via FieldCare
–20 to +60 °COptional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other Status 0/4 to 20 mA, pulse/frequency
(1 kHz passive), status HART®, PROFIBUS PALiquids: ±0.15%Optional: ±0.1%
Gases: ±0.35%ATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
83 High-end
Sensor F, M, A, I, H, E, S, P
Compact SSCompact AluRemote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare
–20 to +60 °C Optional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other
Status, current input
0/4 to 20 mA, pulse/frequency (10 kHz, active/passive), relays, status
HART®, PROFIBUS PA, PROFIBUS DP, FOUNDATION Fieldbus, MODBUS® RS485,
EtherNet/IP
Liquids: ±0.1%Optional: ±0.05%
Gases: ±0.35 %ATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
84 Custody transfer
Sensor F, M, A
Compact SS Compact AluRemote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare
–20 to +60 °COptional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other Status
0/4 to 20 mA, pulse/frequency (10 kHz, active/passive),
2 × pulse (90°/180°), relays, status
HART® MODBUS® RS485
Liquids: ±0.1%Gases: ±0.35 % ATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
TB2 Two-wire
Sensor E (two-wire)
Compact SS Compact Alu
Four-line LCD/ push buttons
Operation via FieldCare –40 to +60 °C Two-wire
18 to 30 V DCElectronical connections are
galvanically isolated from each other Status 4 to 20 mA, pulse/frequency, status HART®, PROFIBUS PA Liquids: ±0.25%
Gases: ±0.75 % ATEX, IEC, cCSAus IP66/IP67 (NEMA 4X)
91 Basic
Sensor W Remote Alu
Two-line LCD/ push buttons
Operation via FieldCare–20 to +60 °C 85 to 250 V AC (45 to 65 Hz)
20 to 28 V AC (45 to 65 Hz) or 11 to 40 V DCElectronical connections are
galvanically isolated from each other – 0/4 to 20 mA, pulse/status HART® Onsite: <2.0% Under reference conditions: ±0.5% FM, CSA Div. 2 IP67
(NEMA 4X)
93 High-end
Sensor W, P, C Remote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare
–20 to +60 °C Optional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other
Status, current input
0/4 to 20 mA, pulse/frequency (10 kHz, active/passive),
relays, status
HART®, PROFIBUS PA, PROFIBUS DP,
FOUNDATION Fieldbus
Onsite: <2.0% Under reference conditions: ±0.5% ATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
92 F Inline
Sensor F
Compact AluRemote Alu
Two-line LCD/ push buttons
Operation via FieldCare
Compact: –40 to +60 °CRemote: –40 to +80 °C
12 to 35 V DC, EEx i: 12 to 30 V DC, EEx d: 15 to 35 V DC
Electronical connections are galvanically isolated from each other – 4 to 20 mA, pulse/status HART®, PFM, PROFIBUS PA,
FOUNDATION Fieldbus
LiquidsFor 2 or 3 beams: ±0.5%
For 4 beams: ±0.3%
ATEX, IEC, FM, CSA, TIISIn preparation: NEPSI
IP67 (NEMA 4X)
93 T Portable
Sensor P Portable Plastic
Four-line, backlit LCD/ touch control
Operation via FieldCare0 to +60 °C Rechargeable battery + charger: 100 to 240 V AC
(47 to 63 Hz)Electronical connections are
galvanically isolated from each other 4 to 20 mA Data logger – Onsite: <2.0% Under reference conditions: ±0.5% – –
72 Standard
Sensor F, W
Compact AluRemote Alu
Two-line LCD/ push buttons
Operation via FieldCare
Compact: –40 to +70 °CRemote: –40 to +80 °C
Two-wire12 to 36 V DC,
EEx i: 12 to 30 V DC, EEx d: 15 to 36 V DC
Electronical connections are galvanically isolated from each other – 4 to 20 mA,
pulse/statusHART®, PFM, PROFIBUS PA,
FOUNDATION FieldbusLiquids: ±0.75% Volume
Gases/steam: ±1.0% Volume ATEX, IEC, FM, CSA, TIIS, NEPSI IP67 (NEMA 4X)
73 With flow computer
Sensor F, W
Compact AluRemote Alu
Two-line LCD/ push buttons
Operation via FieldCare
Compact: –40 to +70 °CRemote: –40 to +80 °C
Two-wire 12 to 36 V DC,
EEx i: 12 to 30 V DC, EEx d: 15 to 36 V DC
Electronical connections are galvanically isolated from each other
Pressure, temperature, density using HART®,
PROFIBUS PA, FF
4 to 20 mA, pulse/status,
frequency
HART®, PFM, PROFIBUS PA,FOUNDATION Fieldbus
Liquids: ±0.75% Volume, ±1% Mass Gases/steam: ±1.0% Volume
Gases/steam: ±1.7% MassATEX, IEC, FM, CSA, TIIS, NEPSI IP67
(NEMA 4X)
65 Standard
Sensor I, F
Compact AluRemote Alu
Two-line, backlit LCD/ push buttons
Operation via FieldCare
–20 to +60 °COptional: –40 to +60 °C
85 to 260 V AC (45 to 65 Hz) 20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DC
Electronical connections are galvanically isolated from each other 4 to 20 mA
0/4 to 20 mA, pulse/frequency (1 kHz, active/passive),
relays, status
HART®, PROFIBUS DP, MODBUS® RS485
Gases: ±1.5% o.r. (10% to 100% o.f.s.)±0.15% o.f.s. (1% to 10% o.f.s.)
ATEX, IEC, FM, CSA, NEPSI IP67
Deltabar SPMD 70/75 Deltatop
Compact SSRemote SS
Compact AluRemote Alu
Four-line LCD/push buttonsOperation via FieldCare –40 to +85 °C Two-wire
11.5 to 45 V DC No galvanic isolation – 4 to 20 mA HART®, PROFIBUS PA, FOUNDATION Fieldbus
Orifice plate DO: ±0.5 to 0.8%Pitot tube DP: ±1.0%
Nozzle DN: ±0.7 to 1.0%Venturi tube DV: ±0.7 to 1.0%
ATEX, IEC, FM, CSA, TIIS, NEPSI IP65
Deltabar MPMD 70/75 Deltatop Compact Alu
Remote Alu
Four-line LCD/push buttonsDIP switch
Operation via FieldCare–40 to +85 °C Two-wire
11.5 to 45 V DC No galvanic isolation – 4 to 20 mA HART®, PROFIBUS PA, FOUNDATION Fieldbus
Orifice plate DO: ±0.5 to 0.8%Pitot tube DP: ±1.0%
Nozzle DN: ±0.7 to 1.0%Venturi tube DV: ±0.7 to 1.0%
ATEX, IEC, FM, CSA, TIIS, NEPSI IP65
Compact version Compact SS Operation via FieldCare –20 to +60 °C 20 to 30 V DC Electronical connections are galvanically isolated from each other – Pulse, status – ±0.5%
Optional: ±0.25% – IP67(NEMA 4X)
Compact version Compact SS Operation via FieldCare –20 to +60 °C 20 to 30 V DC Electronical connections are galvanically isolated from each other – Pulse, status – ±0.15% ATEX II 3G IP67
(NEMA 4X)
Compact versionCustody transfer
Compact Alu Operation via FieldCare –40 to +60 °C 20 to 28 V AC 20 to 30 V DC
Electronical connections are galvanically isolated from each other – Pulse/frequency, status MODBUS® RS485 ±0.5% ATEX, IEC, FM, CSA
In preparation: TIIS, NEPSI IP67
(NEMA 4X)
Compact/remote versionCustody transfer
Compact SSCompact AluRemote Alu
Four-line, backlit LCD/ touch control
Operation via FieldCare–40 to +60 °C 85 to 260 V AC (45 to 65 Hz)
20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DCElectronical connections are
galvanically isolated from each other Status0/4 to 20 mA, pulse/frequency
(10 kHz, active/passive), 2 × pulse (90°/180°), relays, status
HART®, MODBUS® RS485 ±0,5% ATEX, CEC, NECIn preparation: NEPSI
IP67(NEMA 4X)
Compact versionCustody transfer
Compact Alu Operation via FieldCare –40 to +60 °C 20 to 28 V AC 20 to 30 V DC
Electronical connections are galvanically isolated from each other – Pulse/frequency, status MODBUS® RS485 ±0.2% ATEX, IEC, FM, CSA
In preparation: TIIS, NEPSIIP67
(NEMA 4X)
Compact version Compact Alu Operation via FieldCare –40 to +60 °C 20 to 28 V AC 10 to 30 V DC
Electronical connections are galvanically isolated from each other – 4 to 20 mA, pulse/frequency MODBUS® RS485 ±0,1% ATEX, IEC, CEC, NEC
In preparation: TIIS, NEPSIIP67
(NEMA 4X)
Compact/remote versionRemote SS
Compact AluRemote Alu
Two-line, backlit LCD/ touch control
Operation via FieldCare–40 to +60 °C 85 to 260 V AC (45 to 65 Hz)
20 to 55 V AC (45 to 65 Hz) or 16 to 62 V DCElectronical connections are
galvanically isolated from each other Status 4 to 20 mA, pulse/frequency MODBUS® RS485 ±0,1% ATEX, IEC, CEC, NECIn preparation: TIIS, NEPSI
IP67(NEMA 4X)
Compact version Compact Alu LED –20 to +60 °C 20 to 30 V DC No galvanic isolation – 4 to 20 mA, relays – ±2.0% FM, CSA Div. 2 IP66(NEMA 4X)
Compact version Compact SSOne-line, backlit LCD –
Color change on faults, LED’s for status indication, push buttons
–40 to +85 °C 18 to 30 V DC (reverse polarity protection) No galvanic isolation –
1× or 2 × PNP switching outputs,optional: 1× PNP switching output and 1× 4 to 20 mA output, active
Programmable by a PC(ReadWin® 2000 and FieldCare) ±2.0% – IP64
Compact version Compact SSOne-line, backlit LCD –
Color change on faults, LED’s for status indication, push buttons
–40 to +85 °C 18 to 30 V DC (reverse polarity protection) No galvanic isolation –
1× or 2 × PNP switching outputs,optional: 1× PNP switching output and 1× 4 to 20 mA output, active
Programmable by a PC(ReadWin® 2000 and FieldCare) ±2.0% – IP64
Compact version Compact SSCompact Alu
LED, 4-digits, LCD (option)DIL switches
–10 to +65 °C without LCD 18 to 30 V AC/DC No galvanic isolation – Relays – ±5.0% – IP66
Compact version Compact SSCompact Alu
LED, 4-digits, LCD (option) push buttons
–10 to +65 °C without LCD 18 to 30 V AC/DC No galvanic isolation – 4 to 20 mA, open collector – ±5.0% – IP66
Flow measurement
Subj
ect t
o m
odifi
catio
n
Flow measurement OEM
Flow monitoring
TransmittersSensors