FLEXIBLE FUME ARM SERIES “SOURCEARM” · FLEXIBLE FUME ARM SERIES “SOURCEARM” 8-7475 Kimbel Street, Mississauga, ON L5S 1E7 ... attach the second section of the moun ting bracket

SOURCETEC INDUSTRIES INC.

INSTALLATION INSTRUCTION AND MAINTENANCE MANUAL

WARNING!CARELESS OR IMPROPER USE MAY RESULT IN PERSONAL INJURY. READ SAFETY PRECAUTIONS AND INSTRUCTIONS

PRIOR TO OPERATING THIS PRODUCT.

SOURCETEC INDUSTRIES INC.

www.sourcetecindustries.com

TOLL FREE: 1-800-784-2383

OMFLEXARM--2013-01

FLEXIBLE FUME ARM

SERIES “SOURCEARM”

8-7475 Kimbel Street, Mississauga, ON L5S 1E7Tel: (905) 678-9333 Fax: (905) 678-7133

1302 Holloway Road, Holland, OH 43528Toll Free: 1-800-784-2383


ITEM DESCRIPTION

Sourcetec Flexible Fume Arms are specially designed to collect and exhaust fumes from the source.

WARNING!

Large spring is factory installed, do not remove!

While installing, do not place fingers between support.

Do not over tighten the Tie Wraps.

INSTALLATION

1. Unpack the flexible fume arm and check for any damages or shortages. If any, please report to the shipping company immediately.

2. Choose the specified height for mounting.

3. Mount the wall bracket first, using specified bolts, for larger arms use threaded rods with back plates, ensure that the wall bracket is leveled. For ceiling mount check specifications.

4. If applies, attach the second section of the mounting bracket using the provided 3/8” bolt.

5. Attach the eyebolt, to the spring on the second section of the arm.

6. Mount the hood to the arm with the provided 5/16” bolt. Make sure friction disc is between connecting bars.

7. Adjust all joints so the arm is barely standing free. Do not over tighten joints.

8. Mount the solid tube starting from the hood; use the self-tap screws provided for the hood and elbow connection respectively.

9. Run the hose below the arm and attach it by the Tie Wraps provided. Make sure that the hose is running loose under the support to allow it to bend.

10. Tighten the tie wraps just enough to hold hose in place. Do not over tighten.

11. Adjust all joints until you have desired movement of your arm.

12. Cut any hanging tie wraps.

YOUR FUME ARM IS NOW READY TO BE USED.

8-7475 Kimbel Street, Mississauga, ON L5S 1E7Tel: (905) 678-9333 Fax: (905) 678-7133

1302 Holloway Road, Holland, OH 43528Toll Free: 1-800-784-2383


MAINTENANCE

Sourcetec Flexible Fume Arms are designed to essentially be maintenance free. Periodic inspection of the arm on a monthly basis is suggested to reveal any possible deterioration of the following:

Hoses: small holes should be taped of to prevent any further tearing, or be replaced. (Does not apply for steel hoses).

Joints: after a period of time joints may need to be readjusted and cleaned from any atmospheric dust particles. To do so, just slightly release tension on the joints, and clean with compressed air. Tighten and readjust.

Hood Damper: after approximately one month of use, hood damper (if provided) may need to be adjusted, just tighten bolt nuts (1/4” -20) located on either side of the hood.

HOW TO ASSEMBLETHIS JOINT

BOLT 1/2"AND WASHER

NYLOCK 1/2"AND WASHER

SPRING

DETAIL A SCALE 1 : 4

FRICTION DISK GOESBETWEEN BRACKETAND PIVOT

BOLT 5/16"

WASHER

BEVEL WASHER

HOOD PIVOT

NYLOCK 5/16"

WASHER

BEVEL WASHER

HOOD BRACKET

SOURCETEC INDUSTRIESDRAWN BY: L.B.M

TEL: (905) 678-9333FAX: (905) 678-7133

DATE: SEP 8, 2008MATL: MILD STEELSCALE: 1:8

DESCRIPTION:

PRODUCT No:

WGT: XX lbs. DRAWING No: SHEET 1 OF 1

SAL ASSEMBLY

E8109-A0JOB #: 500XXSAL-GENERAL

THIS DOCUMENT IS A PROPERTY OF SOURCETEC INDUSTRIES INC. IT IS NOT TO BE COPIED IN WHOLE OR IN PART FOR ANY PURPOSE OR DISTRIBUTION PUBLICLY TO THIRD PARTIES, OR USED FOR CONSTRUCTION PURPOSES WITHOUT THE WRITTEN CONSENT OF SOURCETEC INDUSTRIES INC.


BOLT 1/2"AND WASHER

NYLOCK 1/2"AND WASHER

SPRING


DETAIL A SCALE 1 : 4

FRICTION DISK GOESBETWEEN BRACKETAND PIVOT

BOLT 5/16"

WASHER

BEVEL WASHER

HOOD PIVOT

NYLOCK 5/16"

WASHER

BEVEL WASHER

HOOD BRACKET

DETAIL B SCALE 1 : 4

BOLT 5/16"

WASHER

BEVEL WASHER

2 FRICTION DISKSBETWEEN PLATES

AND TUBE

WASHER

BEVEL WASHER

NYLOCK 5/16"

TUBE

ARM IN SHIPPING

ARM IN WORK

SOURCETEC INDUSTRIESDRAWN BY: L.B.M

TEL: (905) 678-9333FAX: (905) 678-7133

DATE: SEP 10, 2008MATL: MILD STEELSCALE: 1:12

DESCRIPTION:

PRODUCT No:

WGT: XX lbs. DRAWING No: SHEET 1 OF 1

SAM ASSEMBLY

E8110-A0JOB #: 500XXSAM-GENERAL


WASHER

BOLT 1/2"

WASHER

NYLOCK 1/2"

TIEWRAP TOTIGHT HOSE

THIS JOINTHOW TO ASSEMBLE

THIS JOINTHOW TO ASSEMBLE


INSTALLATION AND MAINTENANCE INSTRUCTIONSFOR SOURCEARMS UP TO 16 FT REACH

BEVEL WASHER

WASHER

WASHER

HOOD

BEVEL WASHER

NYLOCK 5/16"

BRACKET

AND PIVOT

HOOD PIVOT

FRICTION DISK GOESBETWEEN BRACKET

BOLT 5/16" 0SAP GENERAL

L.B.M

TEL: (905) 6SOURCETEC INDUSTRIESDRAWN BY:

E9105-A0REV.

78-9333

OCT 22, 2009

FAX: (905) 678-7133

DATE:

1:20

DESCRIPTION:

MATL:

SCALE: XXPRODUCT No:

WGT: 1 OF 1

SAP ASSEMBLY

DRAWING No: SHEET


WASHER

WASHER

BOLT 1/2"

NYLOCK 1/2"

TIEWRAP TOTIGHT HOSE

HOOD

HANDLE EYEBOLT

EYEBOLT

SPRING

SPRING

HOSE

GEAR CLAMP

BRACKET

GEAR CLAMP

MOUNTING

BRACKET

DOUBLE JOINT

DAMPER

EXTENSION

NOTE:ALLOW EXTRA HOSE BETWEEN JOINTS

HORIZONTAL SECTION

0SAR GENERAL

L.B.M


E7105-A1REV.

78-9333

NOV 22, 2009

FAX: (905) 678-7133

DATE:

1:20

DESCRIPTION:

MATL:


WGT: DRAWING No: SHEET

ASSEMBLING DRAWING

1 OF 1

SAR-GENERAL


DETAIL B SCALE 1 : 12

VERTICAL SECTION

BARM2 ARM1DOUBLE JOINT ARM3 WALL BRACKET

66"

3

14"

494"

81"

"77" 8 "83 85

"4612

17'-11"

0SAR GENERAL

L.B.M


E7105-A2REV.

78-9333

NOV 22, 2009

FAX: (905) 678-7133

DATE:

1:18

DESCRIPTION:

MATL:


WGT: DRAWING No: SHEET

ASSEMBLING DRAWING

1 OF 1

SAR-GENERAL


TIGHT BOLT THAT BEARINGS ARE SNUG BETWEEN BRACKET

INSTALLATION AND MAINTENANCE INSTRUCTIONSFOR SOURCEARMS UP TO 28 FT REACH

BOLT

"

1 1/4"

FLAT WASHER

BEAR

1/2

1/2

1

ING

ING

BOLT

FLAT WASHER

BEAR

FLAT WASHER

"

FLAT WASHER

1 1/4"

FLAT WASHER

BOLT 1

"

FLAT WASHER

"NYLOCK

NUTS

NYLOCK

FRICTION MECHANISM

BRACKET

BIG WASHER

BIG WASHER

DETAIL ANYLOCK

SPRING

SPRING

FLAT WASHER

FRICTION DISK

Warranty and Service Policy

One Year Limited Warranty

Air cleaning products and systems manufactured by Sourcetec Industries Inc. are warranted for a period of one year from date of original purchase. Sourcetec's liability shall be limited to repair or replacement of defective material within the warranty period when returned freight prepaid to its plant or to a service depot designated by Sourcetec. This warranty does not apply to products subjected to any accidents, alteration, abuse, or misuse. Warranties on equipment not of seller's manufacture are limited to terms of warranty furnished by seller's suppliers. Our responsibility ceases upon delivery to any common carrier and we do not, unless previously instructed, insure shipments beyond point of delivery to such a carrier. No material will be accepted for credit when returned without permission. All materials accepted for credit is subject to at least a 25% handling charge, and permission must be obtained before equipment is returned. Equipment specially built to customer specifications and requirements is not subjected to cancellation or returnable for credit under any conditions. We reserve the right to modify or alter materials, dimensions, design and construction when necessary, to improve the performance of our product and/or accessories, or to meet delivery requirements.

Documents

FLEXIBLE FUME ARM SERIES “SOURCEARM” · FLEXIBLE FUME ARM SERIES “SOURCEARM” 8-7475 Kimbel Street, Mississauga, ON L5S 1E7 ... attach the second section of the moun ting bracket