Embed Size (px)
Citation preview
1.5:1
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 1 OF 8
A4BRASS, ALUMINUM, RUBBER
136.15 G
FIRE PISTON
2 3 1
4
5 6
1.5:1
ITEM NO. PART NUMBER QTY.
1 Cylinder 1
2 End Cap 1
3 End Cap O Ring 1
4 Piston O Ring 1
5 Piston 1
6 Piston Handle 1
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 2 OF 8
A4BRASS, ALUMINUM, RUBBER
136.15 G
FIRE PISTON
10
95.25
A
8.80 6.35M10x1.25 - 6H 6.35
18
.65
NOTES, UNLESS OTHERWISE SPECIFIED:FORM 45 SEAL CHAMFER SLOWLY, USE 1.TRIAL AND FIT FOR BEST RESULTSTAP M10 OR 3/8" AS APPROPRIATE.2.CYLINDER BORE 10MM OR 25/64 INCH 3.AS APPROPRIATE.
6.35
45°
DETAIL ASCALE 3 : 1
1.5:1
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 3 OF 8
A46061 ALLOY
49.65 G
CYLINDER
6.35
12
.50
4.76 THRU
5.16
17.06 19.05
3.97 FILLET RADIUS 1.0
18
.65
3:1
NOTES, UNLESS OTHERWISE SPECIFIED:THREAD M10 OR 3/8" AS APPROPRIATE.1.BORE RECESS TO MATCH COMPASS INSERT DIMENSIONS.2.
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 4 OF 8
A4BRASS
23.48 G
END CAP
88.90
7.
14
5.51
4.76 1.60
6.80 63.50M8x1.25 - 6H 12.70
9.
53
2:1
NOTES, UNLESS OTHERWISE SPECIFIED:END HOLE FORMED WITH BS3 CENTER DRILL1.TAP M8 OR 5/16" AS APPROPRIATE.2.O RING GROOVE DIMENSIONS NOMINAL. 3.TRIAL AND FIT REQUIRED TO ACCOMODATE ACTUAL SOURCED O RINGS. RECOMMEND TEST FITTING BEFORE PROCEEDING TO DETERMINE ACTUAL DIMENSION - REFER VIDEO.
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 5 OF 8
A4BRASS
30.22 G
PISTON
12.70 23.42
25.40
5.
84
18
.65
3:1
NOTES, UNLESS OTHERWISE SPECIFIED:THREAD M8 OR 5/16" AS APPROPRIATE.1.
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 6 OF 8
A4BRASS
32.69 G
PISTON HANDLE
7.65
11.21
4.44
8
2:1
NOTES, UNLESS OTHERWISE SPECIFIED:
AFTER FITTING TO THE END CAP, THE OUTER DIAMETER OF THE END CAP O RING 1.EXPANDS TO APPROXIMATELY 12.3mmAFTER FITTING TO THE PISTON, THE OUTER DIAMETER OF THE PISTON O RING EXPANDS 2.TO APPROXIMATELY 10.2mm
END CAP O RING PISTON O RING
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 7 OF 8
A4RUBBER
0.06 G
O RINGS
45°
1.59
14.29
15.88
5.90 9.97
9.
53
5.56 THRU
5:1
NOTES, UNLESS OTHERWISE SPECIFIED:PROFILE DIMENSIONS INDICATIVE ONLY, 1.SHAPE AS DESIRED.
B
C
D
1 2
A
321 4
B
A
5 6
C
B
C
D
1 2
A
321 4
B
A
5 6
MATERIAL:
SCALE:
C
REMOVE ALL BURRS AND SHARP EDGES0.50 RADIUS OR CHAMFER MAX
WEIGHT:
UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR: DIMENSIONS UNDER 15 MM 0.1 DIMENSIONS 15 MM AND OVER 1 ANGULAR: 0.5
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
CLICKSPRINGPROJECTS.COM
TITLE:
SHEET 8 OF 8
A4BRASS
5.40 G
LANYARD BEAD
