Upload
others
View
13
Download
0
Embed Size (px)
Citation preview
FIN
E C
RU
SH
ING
HA
MM
ER
CR
US
HER
High operating reliability
Low cost for operating and maintenance
High throughput
Long service life of main crushing elements
2
HAMMER CRUSHERS FOR FINE CRUSHING
WITH HIGH CAPACITY THE FIELDS OF APPLICATION
Impact hammer crushers are hammer
mills that are particularly used for primary
and secondary crushing of feed materials
from mining and pit and quarry industries.
DSMAC Fine Crushing Hammer Crusher
is suitable for crushing material with
compression strength less than 160 MPa.
Especially suitable for cement industry to
crush brittle material such as limestone,
with surface moisture not greater than 5%.
Also it can be used for fine crushing work
of construction material, chemical
engineering, mining, metallurgical, etc.
Install before mill to increase mill efficiency
and receive best milling performance.
XPCF Series Fine Hammer Crusher
DPX Series Fine Hammer Crusher
3
MAIN CUSTOMER BENEFITS OF FINE
CRUSHING HAMMER CRUSHER
Reversible impact hammer crushers
Mechanically adjustable impact walls
Hydraulically adjustable impact walls
With a replaceable grate
Housing with hydraulic opening mechanism
Here, the operating direction is reversed so that
the beater heads are optimally used without having
to be turned. A number of different drive concepts
are available. Impact hammer crushers can be
operated with constant or variable rotational
speed.
To compensate wear and tear and to vary the grain
spectrum.
For frequent changes in the type of work to be
performed, depending on product quality andgrain
spectrum.
To limit the quantity of oversized grain. Not suitable
for moist, sticky and clayey materials.
To open the housing. The necessary time for
replacing worn-out parts or even a fully-equipped
rotor, is thus considerably reduced.
Fine Hammer crusher DPX-300III – crushing of limestone
for desulphurization
Fine Hammer crusher XPCF500 for limestone Capacity:500 t/h
Fine Hammer crusher for limestone
4
SINGLE STAGE FINE CRUSHERSPECIFICATIONS
Type RotorSize
(mm*mm)
HandlingCapacity
(t/h)
Hammerhead
Number
FeedingHole Size(mm*mm)
Feeding Granularity
(mm)
DischargingGranularity
(mm)
Power (kw)
DPX-15III 800* 650 10-20 12 570*630 ≤500 Davg. ≤5 35-55
DPX-35III 1000*1030 30-40 24 1050*760 ≤ 700 Davg.≤5 55-75
DPX-65III 1200*1290 55-75 24 1320*760 ≤800 Davg.≤5 90-132
DPX-90III 1400*1300 80-100 30 1330*960 ≤900 Davg.≤5 132-160
DPX-125III 1400*1700 110-130 35 1790*960 ≤1000 Davg.≤8 200-240
DPX-150III 1600*1560 140-160 30 1900*960 ≤1100 Davg.≤8 240-280
DPX-180III 1600*2020 160-200 40 2050*1200 ≤1100 Davg.≤10 280-355
DPX-250III 1800*2000 230-280 40 2150*1400 ≤1100 Davg.≤10 440-550
DPX-300III 2000*2200 280-350 50 2300*1600 ≤1100 Davg.≤10 440-550
5
HIGH EFFICIENCY FINE CRUSHER SPECIFICATIONS
Type Rotorsize
(mm*mm) Capacity
(t/h)
Spindlespeed(r/m)
Inputsize(mm)
Outputsize(mm)
MotorPower(kw)
OverallDimension
(L*W*H)
XPCF20 Φ800*400 15-20 813 120 4 30-37 1320*1529*1578
XPCF30 Φ800*600 20-30 813 120 4 37-45 1520*1529*1578
XPCF40 Φ900*600 30-40 807 150 5 37-45 2008*1478*1896
XPCF50 Φ900*700 40-50 807 150 5 45-55 2008*1578*1896
XPCF60 Φ900*900 50-60 807 150 5 55-75 1969*1777*1866
XPCF70 Φ1000*950 60-70 726 200 6 55-75 2337*2054*2167
XPCF80 Φ1000*1100 70-80 726 200 6 75-90 2337*2208*2167
XPCF90 Φ1000*1250 80-90 726 200 6 90-110 2337*2359*2167
XPCF100 Φ1250*1100 90-100 581 250 8 90-110 2915*2153*2480
XPCF125 Φ1250*1350 100-125 581 250 8 110-132 2915*2375*2480
XPCF150 Φ1250*1650 125-150 581 250 8 160-200 2915*2669*2480
XPCF200 Φ1600*1350 150-200 450 300 10 160-220 3178*2604*2810
XPCF250 Φ1600*1600 200-250 450 300 10 220-250 3174*2906*2809
XPCF300 Φ1800*1800 250-300 403 350 12 315-355 3788*3250*3100
XPCF400 Φ1800*2200 300-400 398 350 12 400-450 3862*3663*3500
XPCF500 Φ2000*2405 400-500 363 350 12 500-560 4141*4046*3774
Questionnaire
To enable us to quote for equipment relative to your particular requirements, it will
greatly assist us if all essential information is supplied with the initial enquiry. For
your guidance we tabulate the information required :
Material ..................................................................
Material hardness, or chemical content? ............................................
Feed size ? (mm) ................................................
Your required output size? (mm) ....................
Capacity required in tonnes / hour ...........................
For more requirement, you can send to me now, or later, to our expert mail
ZHENGZHOU DINGSHENG ENGINEERING TECHNOLOGY CO.,LTD
ADDRESS:National HI-TECH Industry Unit B Torch Building, Zhengzhou,China.
TEL:0086-371-67897103 0086-371-53738757
FAX:0086-371-60535395 0086-371-65948723
SKYPE:dscrusher
Email:[email protected]
WEBSITE:www.dscrusher.com
Scanning the codeAbove and then
Entering the website