Fike Agent Storage Containers

8/20/2019 Fike Agent Storage Containers

1/38

HFC-227EA AGENT STORAGE CONTAINERS

DESCRIPTIONFike Series 70 Clean Agent Containers are used in fire extinguishing systems tostore the Clean Agent until a fire develops and the agent must be released. TheClean Agent is retained in the container by a valve assembly which contains afast-acting rupture disc. The disc will be ruptured, and the Clean Agent released,through the operation of an actuator by an electric signal that is automatically ormanually controlled. The valve is available in three sizes: 1" (25mm), 2 1/2"(65mm) and 3" (80mm). The 1" (25mm) valve is used on the 10 (4), 20 (8), 35(15), 60 (27), and 100 pound (44 L) containers; the 2 1/2" (65mm) valve is usedon the 125i (51 L) and 215i pound (90 L) containers; the 3" (80mm) valve is usedon the 215 (87), 375 (153), 650 (267) and 1000 pound (423 L) containers. After adischarge, the valve is field reconditioned by simply replacing three components.

Fike Series 70 Clean Agent Containers have passed extensive testing by

Underwriters Laboratories and Factory Mutual and are used in installations where8 to 1045 pounds (3.5 to 474 kg) of HFC-227ea is required. To eliminate theneed for multiple containers, or using more Clean Agent than necessary, thesecontainers can be filled in 1 pound (0.5 kg) increments to their maximumcapacity.

Each container for HFC-227ea Clean Agent Systems is super pressurized with dry nitrogen to 360 psig (25 bar), at 70° F (21° C), to provide a quick and effectivedischarge in 10 seconds or less.

Fike Series 70 Clean Agent Containers are supplied with a pressure gauge thatpermits a quick, visual, inspection of container pressure. Optional items include aLiquid Level Indicator, and a Low Pressure Supervisory Switch. The Liquid Levelindicator provides the convenience of determining the container's agent weight

without removing it from its installed location. The Low Pressure Supervisory Switch provides constant monitoring of the container's internal pressure and can be wired either normally opened or normally closed. In the event of a decrease incontainer internal pressure from 360 psig to 288 psig (24.8 bar to 18.8 bar), theSupervisory Switch normally opened/closed contacts will close/open. This willcause a supervisory trouble alarm at the system control panel.

Fike Series 70 Clean Agent Containers are available for installation in the upright,inverted or horizontal positions, depending upon the user's particular needs and thetype and size container specified. The mounting location of the container is quiteflexible. It can be mounted at the exact point of discharge or at a remote locationby adding distribution piping from the container to the nozzle system. (Refer to theFike Design, Installation and Maintenance Manual - P/N 06-215).

The operating temperature range is +32 to +130oF (0 to 54.4oC) in any

installation. If the Clean Agent reaches an internal temperature range of 160° to187° F (71.1°to 86.1°C), it will create a sufficient internal pressure to burst therupture disc and release the Clean Agent through the piping network.

704 S. 10th Street · P.O. Box 610 · Blue Springs, Missouri 64013-0610 U.S.A. · (816) 229-3405 · (816) 229-4615 · www.fike.com

APPROVALS

• UL Listed, Ex4623

• FM Approved 0Y4AB.AF (HFC-227ea)

Series 70 Clean Agent Containers

Form No. C.1.01.01-2


2/38

"B"

"A"

Liquid Level Boss

3" (80mm) Outlet1/2" (15mm)

Electrical

Connection

"B"

"A"

Liquid Level Boss

1" (25mm) Outlet

1/2" (15mm)

Electrical

Connection

"A"

"B"

Liquid Level Boss

2-1/2" (65mm) Outlet1/2" (15mm)

Electrical

Connection

DESCRIPTION (cont.)

Reliability

Fike Series 70 Clean Agent Containers are manufactured in strict accordance withDepartment of Transportation (DOT) regulations. The Fike Series 70 Clean Agent

Containers have successfully passed testing by Factory Mutual and UnderwritersLaboratories, Inc. Before leaving the factory, each container must pass extensive leakagetesting, and pressure testing to 1000 psig (69 bar). The containers are constructed fromcarbon steel alloys and painted with a durable, baked enamel finish.

InstallationFike Series 70 Clean Agent Containers are supplied with a mounting bracket that isdesigned to provide the most effective and versatile installation for that particularcontainer. The 10, 20 and 35 pound (4, 8 and 15 L) container brackets employ two U-bolts for securing the container to the bracket. The 60 pound (27 L) container is securedusing two quick connecting, over-center handle clamps. The 125i and 215i pound (51 and90 L) containers utilize an "L" shaped bracket for direct wall mounting or, with anoptional floor mounting kit, can be mounted on a floor in the "valve down" position. The100 pound (44 L) and 215 pound (87 L) through 1000 pound (423 L) containers are

supplied with one or two U-shaped mounting brackets, depending upon container size,for mounting to a wall or other secure surface.

Container Sizes and Dimensions: U.S. Standard and Metric

Size-lb 10 20 35 60 100 125i 215i 215 375 650 100

A(in) 7 7.25 7.25 10.75 10.75 20.00 24.00 20.00 20.00 24.00 24.00

B(in) 14.12 21.50 32.50 28.00 38.75 20.25 23.75 28.87 42.50 48.75 70.00

Size-L 4 8 15 27 44 51 90 87 153 267 423

A(mm) 178 184 184 273 273 508 610 508 508 610 610

B(mm) 359 546 826 711 984 515 605 733 1080 1237 1778

U.S. SIZES & DIMENSIONS

METRIC SIZES & DIMENSIONS


3/38

AVAILABLE MODELS AND SPECIFICATIONS

FIKE P/N SIZE (LB) VALVE (IN)EMPTY WT

(LB)

HFC-227ea

AGENT FILL

RANGE (LBS)

VALVE

POSITION

DOT

REGULATION

70-108 10 1 15 8-10 horiz or upright 4BW500




70-153 100 1 61 63-108 upright 4BW500

70-041 125i 2 ½ 180 73-126 inverted 4BA500

70-077 215i 2 ½ 225 128-223 inverted 4BA500

70-154 215 3 150 124-216 upright 4BW500

70-155 375 3 218 217-378 upright 4BW500

70-156 650 3 350 378-660 upright 4BW500

70-157 1000 3 515 598-1045 upright 4BW500

FIKE P/N SIZE (L)VALVE

(MM)

EMPTY WT

(KG)

HFC-227ea

AGENT FILL

RANGE (KG)

VALVE

POSITION

DOT

REGULATION

70-108 4 25 7 4.0-4.5 horiz or upright 4BW50070-098 8 25 10 5.5-9.5 horiz or upright 4BW500

70-089 15 25 15 10.0-17.0 horiz or upright 4BW500

70-152 27 25 20 18.0-30.5 horiz or upright 4BW500

70-153 44 25 28 28.5-48.5 upright 4BW500

70-041 51 65 82 33.5-57.0 inverted 4BA500

70-077 90 65 102 58.5-101.0 inverted 4BA500

70-154 87 80 68 56.5-98.0 upright 4BW500

70-155 153 80 99 98.5-171.5 upright 4BW500

70-156 267 80 159 171.5-299.0 upright 4BW500

70-157 423 80 234 271.5-474.0 upright 4BW500

CLEAN AGENT STORAGE CONTAINER DATA - U.S. STANDARD

CLEAN AGENT STORAGE CONTAINER DATA - METRIC


4/38

Copyright © Fike Corporation All Rights Reserved.Form No. C.1.01.01-2 March, 2005 Specifications are subject to change without notice.

ARCHITECT AND ENGINEERING SPECIFICATIONS

The Clean Agent shall be stored in Fike Series 70 Clean Agent Storage Containers. The containers shall be capable of being filled, in one-pound (0.5kg) increments, to their listed maximum capacity. The Clean Agent container shall be activated by asignal from the control panel which is processed by the Agent Release Module. This module shall store the power requiredto operate the actuator. The valve shall contain a scored, non-fragmenting, rupture disc to provide an immediate, total

discharge of all the agent. HFC-227ea Clean Agent is stored in the container as a liquid, having a natural vapor pressure of 66 psig at 77°F (5 barg at 25°C). To aid in discharge, the container shall be super-pressurized to 360 psig at 70°F (25 bar at21.1°C) with dry nitrogen. Agent discharge shall be completed in 10 seconds or less.

Clean Agent Storage Containers shall be actuated by an electrical signal that is automatically or manually controlled. Normaloperating temperature shall be +32 to +130°F (0 to 54.4°C) in any installation.

Clean Agent Storage Containers shall be equipped with a pressure gauge to display internal pressure. This gauge shall be anintegral part of the container and color coded for fast referencing of pressure readings. A Low Pressure Supervisory Switchshall be made available as an option. A decrease in internal container pressure from 360 psig to 288 psig (24.8 bar to 18.8bar) shall cause the normally opened/closed Supervisory Switch contacts to close/open, indicating a trouble or supervisory condition at the control panel.

Clean Agent Storage Containers shall be fastened to a wall, or other secure surface, using a mounting bracket that isdesigned for the most effective and versatile installation of each container.


5/38

HFC-227EA PRE-ENGINEERED NOZZLES

DESCRIPTIONNozzle

The function of the Fike Nozzle in a fire suppression system, is to distribute theClean Agent in a uniform, predetermined pattern and concentration. The nozzlesare designed to complete the discharge of Clean Agent in 10 seconds or less

when installed within the design limitations of the Fike Design Manual, P/N 06-202 or 06-215.

Fike Nozzles are available in five sizes. Each nozzle comes in two configurationsof 180 and 360 degree distribution patterns.


Fike Pre-Engineered Nozzles

360O PRE-ENGINEERED NOZZLES

PART NUMBER DESCRIPTION

80-052-0625 3/8" (10mm)

80-052-0781 1/2" (15mm)

80-1114 1" (25mm)

80-1115 1-1/2" (40mm)

80-1118 2" (50mm)

180O PRE-ENGINEERED NOZZLES

PART NUMBER DESCRIPTION

80-1113 1" (25mm)80-1115 1-1/2" (40mm)

80-1117 2" (50mm)

Form No. C.1.02.01-3


The Nozzle used to distribute the Clean Agent shall be a Fike Series 80. The nozzle shall be available in 3/8" (10 mm),1/2" (15mm), 1" (25mm), 1 1/2" (40mm) and 2" (50mm) sizes. Each nozzle is available in two styles: 180 and 360 degreedistribution patterns. The nozzle used shall be provided with internal pipe threads that correspond to the nozzle size. Thenozzle used shall be Underwriters Laboratories listed and Factory Mutual approved. (See diagrams on next page for nozzlesize/area coverage). The Fike Nozzle is provided with pipe threads that correspond to the nozzle size. With thisarrangement, the Fike Nozzle can be installed directly at the Clean Agent container or remotely, at the end of a dischargepiping system.

.

APPROVALS

• UL Listed - Ex 4623

• ULC Listed - CEx624

• FM Approved - 0Y4A8.AF


6/38


Nozzle Size and Area Coverage

NOTES:

a. An allowable area of coverage includes any area where the maximum coverage from the nozzle ("R" dimension) is not exceeded.

b. Nozzles should be located on center line of hazard area.

c. When working with ceiling heights exceeding the values tabulated above, the hazard volume must be broken down into vertically stacked hazard volumes, with heights less than the maximums shown in the table. It is imperative that unusual applications of this nature be handled by experienced people in the field, and in most cases, operational tests should be performed before the system is put into service.

d. Dimensions and nozzle data shown are taken from the UL listed and FM approved Design, Installation & Maintenance Manual - P/N 06- 202 or 06-215.

e. 180 and 360 degree nozzles may be placed a maximum of 1 foot (30.5cm) down from the ceiling, and 180 degree nozzles may be placed a maximum of 1 foot (30.5cm) from the wall.

Nozzle Area Coverage

Nozzle TypeRadius “R”

Dimension (English)

Radius “R”

Dimension (Metric)

Ceiling Height

Range (English)

Ceiling Height

Range (Metric)

180o 45'-8" 13.92m 12 in. to 16 ft. 0.3 to 4.88m

360o 29'-8" 9.04m 12 in. to 16 ft. 0.3 to 4.88m

R

R

180° Nozzle 360° Nozzle


7/38

HFC-227EA CONTAINER ACCESSORIES

DESCRIPTION

Reload Kit HFC-227ea

85-023 - 1" (25mm) Valve and 85-024 - 2 1/2" (65mm) Valve

The Series 85 Reload Kits are designed to facilitate field reconditioning of thecomplete line of Fike Clean Agent Containers. The 1" (25mm) Reload Kit willservice the 10, 20, 35, 60 and 100 lb. (4, 8, 15, 27, 44 liter) Fike Containers. The2 1/2" (65mm) kit will service the Fike 125i and 215i lb. (51 & 90 liter)Containers. Generally, each kit consists of a rupture disc, a gas cartridge actuatorand actuator housing, pressure gauge, replacement core for the fill valve, O-ring,and a teflon ring.

Reload Kit HFC-227ea85-025 - 3" (80mm) Valve

The 3" (80mm) Reload Kit provides field reconditioning of the 215, 375, 650,and 1000 lb. (87, 153, 267, 423 liter) Containers. Each kit consists of a 3" (80mm)rupture disc valve assembly, gas cartridge actuator, "O"-rings, pressure gauge andreplacement core for the fill valve.

Low Pressure Switch

70-1121 - All Containers Over 10 lb. (4 liters)

70-1650 - 10 lb. Container Only

These devices monitor the pressure within the Clean Agent Container. Should

loss of Agent or Nitrogen occur, the Pressure Switch's normal contacts willtransfer indicating a low pressure condition.

Specifications

• Temperature Limits: 32° to 120° F (0-48.9°C)

• Enclosure Classification: NEMA 4

• Contact Rating: Single pole, double throw; 5 amps resistive, 3 ampsinductive @ 30VDC

• Body Material: Aluminum with irridite finish

• Weight: 6.5 ounces• Pressure Connection: 1/8” NPT (6mm)

• Electrical Connection: 1/2” NPT (15mm)

• Pressure Setting: 288 psig (20 bar)(decreasing)


APPROVALS

• UL Listed - Ex4623


Reload Kit (1” and 2 1/2”)

Reload Kit (3”)

Pressure Switch

Form No. C.1.03.01-2


8/38

Copyright © Fike Corporation All Rights Reserved.Form # C.1.03.01-2 March, 2005 Specifications are subject to change without notice.

Victaulic Nipple and Coupling

Check Valve

02-2980 - 1" Check Valve (25 mm)

02-4158 - 2" Check Valve (40 mm)

02-4157 - 3" Check Valve (80 mm)

The Fike Check Valve prevents agent loss from the open end of a manifold and/orpiping system in the event that one or more containers are removed for servicing and the system is discharged. This applies to all manifold configurations including Main/Reserve Systems.

Constructed of carbon steel, the Check Valve has a working pressure of 720 psig (4965 kPa) and has 1", 2" or 3" (25, 50 or 80 mm) female NPT threads.

Equivalent Length Values:

1" (25 mm) - 2 ft./0.61 m

2" (50 mm) - 4 ft./1.22 m

3" (80 mm) - 4 ft./1.22 m

DESCRIPTION (CONT.)

Victaulic Nipple and Coupling

02-1388 - 2 1/2” (65mm) Victaulic Nipple

02-1376 - 2 1/2” (65mm) Victaulic Coupling

02-2106 - 3” (80mm) Victaulic Nipple

02-1987 - 3” (80mm) Victaulic Coupling

The purpose of the 2 1/2" (65 mm) and 3" (80 mm) victaulic nipple and coupling is to connect the 2" (55 mm) or 3" (80 mm) check valve(s) and/or system piping tothe 2 1/2" (65 mm) or 3" (80 mm) container valve. The coupling is rated at 1000psi (6895 kPa) working pressure and contains a Buna "N" gasket. The nipple is Sch.40 pipe, has 2 1/2" (65 mm) or 3" (80 mm) NPT male thread at one end and a 21/2" (65 mm) or 3" (80 mm) Victaulic groove on the opposite end.

Check Valve


9/38

AGENT RELEASE MODULE

DESCRIPTION

The Agent Release Module (ARM III), Fike P/N 10-1832, in conjunction with aFike Control Panel, allows the electrical actuators used with Fike Clean Agentcontainers to be wired in parallel. This configuration substantially increases theoverall reliability of the Clean Agent releasing circuit. With series-wired actuatorcircuits, a problem in a single actuator will incapacitate the entire system. Utilizing parallel-wired actuators, that same incident would incapacitate only that individualClean Agent container; all others would still be active.

The Agent Release Module (ARM III) is compatible with either Class A or ClassB wiring. When an ARM III is used in a Class A wiring configuration, theresulting system is the most reliable available for today's Fire Protection.

Installation

The Fike Agent Release Module (ARM III) is mounted in the lower right corner of a 4 11/16" (11.9 cm) square box which connects to the actuator boss on the Clean Agent container. The ARM III is a solid-state circuit board and contains a terminalstrip for the connections of field wiring and actuator leads. The module is alsoequipped with a polarity diode that illuminates if the field wiring has been installed with reversed polarity. Special care should be taken to assure proper polarity.


Each Clean Agent container shall be provided with a Fike P/N 10-1832 AgentRelease Module (ARM III) to allow all electrical actuators to be connected inparallel. Series-wired actuators are not acceptable. The ARM III shall be locatedat each container and shall be securely mounted in the lower right hand corner of a 4 11/16" (11.9cm) square electrical box, with cover. All wiring to the Clean Agent container and the actuator leads shall connect to a terminal strip located onthe ARM III.


APPROVALS

• UL Listed - S3217

• FM Approved

• Cheetah: 0B4A6.AY

• Rhino: 0Y4A4.AY

• SHP Pro: 0Z8A0.AY

Fike Agent Release Module

Form No. C.1.04.01-2

10-1832 ARM

1.5K EOL

+ - R B Y G - +

10-1832 ARM

+ - R B Y G - +TO CONTROL PANEL

Maximum of 6 ARMs

WIRING DIAGRAM


10/38


This page intentionally left blank.


11/38

HFC-227EA LIQUID LEVEL INDICATOR

DESCRIPTION The Fike 70-1353 series Liquid Level Indicator is asimple manually operated device which provides ameans to determine the Clean Agent liquid level in

vertically mounted agent storage containers. Once theliquid level is determined, it can then be convertedinto pounds (kilograms) of Clean Agent present in theagent storage container. (Refer to Fike HFC-227eaInstruction Manual for Liquid Level Indicator (LLi),P/N 06-107.)

Operation

A magnet equipped float moves with the liquid level along the unit stem. Levelreadout is obtained by simply removing the protective cap and pulling out a

calibrated tape until magnetic interlock with the float is felt. With the tape in thisposition, the reading is obtained at the point where the tape emerges from theunit housing.

When the liquid level is determined, the reading is then located on a chart and thecorresponding Clean Agent weight is read. Accurate readings can be obtainedover a +40 to +90oF (+4.4 to +32.2oC) temperature range.

Features

• Reduced maintenance time - the weight of the agent in storage containers canbe determined in a fraction of the time it would take to remove and weighthem.

• Continuous fire protection - use of the liquid level indicator does not requireshutting down the Clean Agent System, thus affording uninterrupted fire

protection.• Field installation capability - the indicator can easily be installed in the field

using a single wrench, as long as the container is empty and is equipped with amounting boss.

• Compact - when not in use, the unit requires no more space than that requiredby the container.

• Flexibility - the flexible tape design allows the unit to be used in tight spacesthat would otherwise hinder the use of a rigid indicator "stick".

• Availability - units are available for Fike container sizes of 100 lb. (44 liter)through 1000 lb. (423 liter) in both the modular and central storage typedesigns.

Construction

The Fike 70-1353 series Liquid Level Indicator housing and stem assembly isconstructed of brass. The flexible indicator tape is constructed of steel with ayellow mylar coating. The indicator tape is calibrated in inches and centimeters.

The unit housing provides straight mounting threads with a static O-ring seal. The float is constructed of a special ECCO material for high pressure service. The cellular construction of the ECCO material allows the float to be solid and isnot susceptible to water-logging, as hollow floats are if they develop a leak. Theunit is provided with a plastic protective cap.


APPROVALS

• UL Ex4623

• FM 3002238

• USCG 162.161/2/0

Liquid Level Indicator

Form No. C.1.05.01-2

MAGNETIC

FLOAT

LIQUID LEVEL

UNIT STEM

LLi BOSS

READ HERE

INDICATOR TAPE


12/38



Agent storage containers of 100 lb. (44 liter) capacity or more shall be provided with a reliable means, other than weighing,of determining the agent weight within the storage container during normal routine service.

The device used shall be a Fike 70-1353-xx series Liquid Level Indicator and shall not require any additional space when thecontainer is installed.

Use of the indicator shall not require the Clean Agent System to be shut down, thus allowing uninterrupted fire protectionduring service intervals. Level indicators which are not factory installed shall be capable of being retrofitted in the field,

with a single standard wrench, when the container is removed for recharge.

The level indicator tape shall be flexible to allow use in confined spaces. The unit housing shall be constructed of brass with straight mounting threads and a static O-ring seal. The float shall be of solid construction to eliminate the possibility of water logging to which hollow floats are susceptible. The float shall be equipped with a magnet which provides for apositive feel when the magnetic interlock is reached between the float and indicating tape.

When the level reading is obtained, the agent weight can be determined through the use of the chart or graph found in the

Liquid Level Indicator Manual (P/N: 06-107). Accurate readings shall be capable of being obtained over a +40oF (+4.4oC)to 90oF (+32.2oC) temperature range.

AVAILABLE MODELS

INDICATOR P/N DIMENSION “L” CONTAINER SIZE CONTAINER P/N

70-1353-22 22” (381 mm) 100 lb (44 liter) 70-153

70-1353-11 11” (278 mm) 125i lb (51 liter) 70-041

70-1353-15 15” (381 mm) 215 lb (87 liter) 70-154/S70-154

70-1353-15 15” (381 mm) 215i lb (90 liter) 70-077

70-1353-24 24” (610 mm) 375 lb (153 liter) 70-155 / S70-155

70-1353-38 38” (965 mm) 650 lb “short” (267 liter “short”) 70-156 / S70-156

70-1353-44 44” (1118 mm) 1000 lb (423 liter) 70-157 / S70-157

"L"

Float

Inspection

Tag

Cap

Measuring

Tape


13/38

INTERFACE FIRING MODULE

DESCRIPTION

The Interface Firing Module (IFM), Fike P/N 10-2136, is designed to allow an

existing control panel (approved for releasing service) to connect with a Fike Clean Agent system. The IFM is designed to operate from any of three different inputsignals from a listed control panel:

Dry Contact A dry contact closure from a releasing circuit of a UL listed control panel willcause the IFM to enter the release state after the contacts are closed for a minimumof 1.1 seconds. When using dry contact output, all interface wiring must be in thesame room, within 20' of the panel, and in EMT or conduit.

Polarity Reversal A polarity reversal circuit input (full reversal required) from a releasing circuit of aUL listed releasing control panel will cause the IFM to enter the release state afterthe polarity signal is reversed for at least 1.1 seconds. The listed releasing controlpanel supervises this circuit by allowing current to flow in one direction during

normal operation and the reverse direction during the discharge state. When theIFM enters a trouble state, and immediately after power-up, the IFM opens thepolarity reversal circuit to signal a trouble condition at the control panel. Thepolarity reversal circuit can be wired for Class A or Class B operation. If wired forClass B operation, the EOL resistor must be installed across terminals 5 and 8.(Value determined by specific panel manufacturer.)

Series Firing A series firing circuit from a compatible control panel which is UL listed forreleasing operation will cause the IFM to enter the release state after a sufficiently large current is passed through the circuit for at least 1.1 seconds. The panelsupervises the circuit by passing a lesser current level through the circuit. When theIFM enters a trouble state, and immediately after power-up, the IFM opens theseries firing circuit to signal a trouble condition on the control panel.

The IFM is provided with an agent release circuit that is capable of connecting with up to 20 Containers/Agent Release Modules (ARM III, Fike P/N 10-1832).It also supervises the integrity of the ARM circuit via Class B wiring by utilizing a1.5K ohm end-of-line device connected at the ARM.

Upon activation of any one of the three types of inputs for a period of at least 1.1seconds, the IFM will energize the ARM III module(s), which in turn fires theactuator(s) to release the agent.

The programmable output contact is a form A dry contact which can be set viaDIP switches for NO or NC operation. It also can be programmed for activationupon trouble or system alarm.

The IFM is a power limited device which requires 24VDC input power from theexisting control panel.

This module is designed to electrically isolate the input circuits from the output

circuits to provide flexibility.

INSTALLATION

The IFM is housed in an enclosure (4" x 3" x 1.5") (10.2 x 7.6 x 3.8 cm). Thishousing can be mounted in the control panel or a separate enclosure. An optionalmetal enclosure (10" x 6" x 2.5") (25.4 x 15.2 x 6.4 cm) with cover is offered; P/N10-2137.

All wiring shall be with conductors approved for use in this application. The IFMincludes a removable terminal strip that can accommodate wiring sizes from 18 to14 AWG.


APPROVALS

• UL/cUL Listed - S5566

Interface Firing Module

Form No. C.1.06.01-2


14/38


STANDARD FEATURES/SPECIFICATIONS

• Interfaces with existing approved releasing control panels

• Operates from any one of three differentinputs

• Connects up to 20 Agent Release Modules(ARMs)

• Supervises the ARM circuit

• Has test mode

• Provides programmable output contact

• Operating Voltage: 21-27 VDC

• Current:- Normal 45 mA Max.- Release 70 mA Max.- Trouble 150 mA Max.

Inputs

• Polarity Reversal Input

- Maximum supervision voltage 30 VDC- Maximum release voltage 30 VDC- Minimum release voltage 12 VDC- Minimum release current required 5 mA

• Series Firing Input- Maximum supervision current 3.0 mA- Minimum release current 8.0 mA- Maximum release voltage 25.5 VDC

- Minimum release voltage 20.7 VDC- Typical input impedance 1.5K ohm

• Dry Contact Input- Maximum Voltage across contact 30 VDC- Maximum Current through contact 50 mA

Outputs

• Dry Contact Output Rating - Maximum voltage 30 VDC- Maximum current 1.0 A

• ARM Circuit rating - Maximum Agent Release Modules 20

WIRING DIAGRAM

1

2

3

4

5

6

7

8

9

10

11

12

13

14

P/N 10-1832

(ARM III)

MODULE

RELEASE

AGENT

GCA

1.5K OHM

2 WATT

UP TO 20 AGENT RELEASEMODULES PER CIRCUIT

EXTERNAL EOL

+

-

+

-

DRY CONTACT INPUT

AGENT RELEASE

POLARITY REVERSALCIRCUIT

SERIES FIRING CIRCUIT

DRY CONTACTOUTPUT

POWER INPUT

MODULE

UL Listed Control Panel Approved For Releasing Service

CIRCUIT

(POLARITY SHOWN IN

DISCHARGE CONDITION)

24VDC 0.2 AMP

Use one of three outputs Contact Monitor Circuit

(for release or trouble

feedback)

INTERFACE FIRING

24 VDC Power

-

+

8

7

6

5

4

3

2

1

RED

BLU

YEL

GRN

AGENT

RELEASE

MODULE

(ARM III)

P/N 10-1832

+

-

1

2

3

4

5

6

7

8

+

-

GRN

YEL

BLU

RED

GCA

-

+

-

+


15/38

HFC-227EA

APPLICATION/DESCRIPTION

HFC-227ea provides superior fire protection in a wide range of applications fromsensitive electrical equipment to industrial applications using flammable liquids.HFC-227ea is ideal for applications where clean-up of other media presents aproblem, where weight versus suppression potential is a factor, where anelectrically non-conductive medium is needed and where people compatibility isan overriding factor. When environmental impact is a consideration, HFC-227eais particularly useful. It has zero ozone-depleting potential, low global warming potential and a short atmospheric lifetime. These characteristics make it suitablenot only for new installations using Fike’s total flooding systems, but also forHalon 1301 replacement applications.

HFC-227ea is an odorless, colorless, liquefied compressed gas. (See PhysicalProperties Table for additional information). It is stored as a liquid and dispensed

into the hazard as a colorless, electrically non-conductive vapor that is clear anddoes not obscure vision. It leaves no residue and has acceptable toxicity for use inoccupied spaces at design concentration. HFC-227ea extinguishes a fire by acombination of chemical and physical mechanisms. HFC-227ea does not displaceoxygen and therefore is safe for use in occupied spaces without fear of oxygendeprivation.

Performance

HFC-227ea is an effective fire extinguishing agent that can be used on many typesof fires. It is effective for many surface fires, such as flammable liquids, and mostsolid combustible materials.

On a weight-of-agent basis, HFC-227ea is a very effective gaseous extinguishing agent. The HFC-227ea extinguishing concentration for normal Class Acombustibles is 6.25 - 7% by volume. The minimum design concentration fortotal flood applications should be in accordance with NFPA 2001.

Specifications

HFC-227ea is manufactured to these specifications:• Mole%: 99.0 Minimum• Acidity, ppm by weight: 3.0 Maximum• Water content, % by weight: 0.001 Maximum• Non-volatile residues, gram/100mL: 0.05 Maximum

Toxicity

The toxicology of HFC-227ea compares favorably with other suppression agents. The LC50 of HFC-227ea is greater than 800,000 ppm. HFC-227ea has beenevaluated for cardiac sensitization via test protocols approved by the United

States Environmental Protection Agency. Test results show that cardiac toleranceto HFC-227ea is higher than that of other suppression agents and is acceptablefor safe use in occupied spaces. HFC-227ea will decompose to form halogenacids when exposed to open flames. The formation of these acids is minimizedby using Fike early warning detection systems and proper system installation. When properly applied and installed, the generation of these by-products of HFC-227ea should be minimal.


APPROVALS

HFC-227ea complies with NFPAStandard 2001 - current edition. FikeHFC-227ea systems are UL listedand FM approved for Clean AgentFire Suppression Systems.

• UL Listed Ex 4623

• FM Approved 0Y4A8.AF

• USCG 162.161/2/0

Form No. C.1.07.01-2


16/38


PHYSICAL PROPERTIES

• Chemical Name: Heptafluoropropane (CF3CHFCF3 )

• Molecular Weight: 170.03

• Boiling Point @ 760 mm Hg: 2.55oF (-16.4oC)

• Freezing Point : -204oF (-131.1oC)

• Critical Temperature: 215oF (101.7oC)

• Critical Pressure (psia): 422 psia (2912 kPa)

• Critical Volume (ft3/lbm) (cc/mole): 0.0258 (274)

• Critical Density (lbm/ft3): 38.8 (621 kg/m3 )

• Specific Heat, Liquid (BTU/lb-Fo ) @ 77oF (25oC): 0.283 (1.184 kj/kg/oC)

• Specific Heat, Vapor (BTU/lb-oF) @ constant pressure of 1 ATM @ 77oF (25oC):0.1932 (0.808 kj/kg/oC)

• Heat of Vaporization (BTU/lb) at Boiling Point: 57.0 (132.6 kj/kg)

• Thermal Conductivity (BTU/h ftoF) of Liquid @ 77oF (25oC): 0.040 (0.069 w/moC)

• Viscosity, Liquid (lb/ft hr) @ 77oF (25oC): 0.443 (0.184 centipoise)

• Vapor Pressure (psia) @ 77

o

F (25

o

C): 66.4 (457.7 kPa)• Ozone Depletion Potential: 0

• Estimated Atmospheric Lifetime (years): 31-42

• LC50 (Rats; 4hrs - ppm): >800,000


17/38

HFC-227EA ENGINEERED NOZZLES

DESCRIPTION The function of the Fike Engineered Discharge Nozzle in a fire extinguishing system is to distribute the Clean Agent in a uniform, predetermined pattern andconcentration. The nozzles are designed to complete the discharge of Clean

Agent in 10 seconds or less when installed within the design limitations of theFike Design, Installation and Maintenance Manual, P/N 06-202 or 06-215 and theFike Flow Calculation computer program.

Fike Engineered Discharge Nozzles are available in sizes of 3/8" (10mm)through 2" (50mm). Each nozzle is available in 180 and 360 degree dischargepatterns.

The Discharge Nozzle size refers to the size of Schedule 40 or 80 steel pipe to which it can be connected. The nozzle discharge orifices are drilled perpendicular

to the center line of the threads. The nozzles are mounted to allow the agent tobe discharged on a horizontal axis.

Nozzle orifices are available in a wide range of sizes to provide accurate Clean Agent flow results. All nozzles have been tested for their ability to discharge theClean Agent under extreme conditions.

Nozzle orifice drilling must be done at the Fike factory, or other UL listed nozzledrill station, only after "As-Built" calculations of the installed piping system(s)have been performed, using the Fike Flow Calculation computer program.

The Fike Discharge Nozzle used shall be Factory Mutual (FM) approved andUnderwriters Laboratories (UL) listed.


Fike Engineered Nozzles

APPROVALS

• UL Listed - Ex4623

• ULC Listed - CEx1136


Form No. C.1.08.01-2


The nozzle used to disperse Clean Agent shall be a Fike Series 80. The nozzle shall be available in 3/8" (10mm) thru 2"(50mm) sizes. Each size shall be available in both 180 and 360 degree dispersion patterns. The nozzle used shall have pipethreads that correspond to the nozzle size. All nozzles shall have an orifice size determined by a UL listed and FMapproved flow calculation program. All nozzle orifice drilling shall be performed by the manufacturer or a UL listed nozzledrilling facility.


18/38


Nozzle Size and Area Coverage

NOTES:

a. The maximum allowable area of coverage includes any area within the radius distance from the nozzle ("R" dimension) to the most extreme wall or corner.

b. Nozzles should be located on center line of hazard area.

c. When working with ceiling heights exceeding the values tabulated above, the hazard volume must be broken down into vertically stacked hazard volumes, with heights less than the maximums shown in the table.

It is imperative that unusual applications of this nature be handled by experienced design engineers and, in most cases, operational tests should be

performed before the system is put into service.d. Dimensions and nozzle data shown are taken from the UL listed and FM approved Design, Installation & Maintenance Manual -

P/N 06-202 or 06-215.

e. 180 and 360 degree nozzles may be placed a maximum of 1 foot (30.5cm) down from the ceiling, and 180 degree nozzles may be placed a maximum of 1 foot (30.5cm) from the wall.

f. Nozzle threading is NPT.

NOZZLE SIZE 180O NOZZLE 360O NOZZLE

(NPT) (mm) PART NUMBER PART NUMBER

3/8" (10) 80-060 80-052

1/2" (15) 80-061 80-053

3/4" (20) 80-062 80-054

1" (25) 80-063 80-0551 1/4" (32) 80-064 80-056

1 1/2" (40) 80-065 80-057

2" (50) 80-066 80-058

180° Nozzle 360° Nozzle

R

R

Nozzle Area Coverage

Nozzle Type“R”

Dimension

Ceiling Height

Range

180 Degree 45’ - 8” (13.92)1.0 to 16.0

(0.3 to 4.9)

360 Degree 29’ - 8” (9.04)1.0 to 16.0

(0.3 to 4.9)


19/38

HFC-227EA INSTRUCTIONAL SIGNS

APPLICATIONInstructional signs must be supplied in order to provide a system in which thefunction of all devices is easy to understand. Fike offers several different standardsigns that comply with NFPA and other industry requirements. All signs aredurable plastic and backed with a strong adhesive for easy installation. Signs aretypically installed at all entrances (CAUTION - Room Protected By HFC-227ea)and near any device for which the extra explanation is helpful. Custom signs areavailable upon special request.

System “Release” Sign/Manual Release Station 02-10137

The purpose of the System "Release" Sign is to identify the manual release stationas the place where the HFC-227ea System can be manually discharged. It alsominimizes the possibility of the manual station being mistaken for a fire alarmdevice. The sign is 4" x 2.25" x 1/16" (102 x 57 x 1.6mm) and is constructed of

red plastic with white lettering. The System "Release" Sign should normally belocated under each HFC-227ea manual release station for quick positiveidentification.

Upon Device Activation "Do Not Enter” Sign 02-10138

The purpose of the System Discharge Sign is to explain the presence of an alarmin the event of a HFC-227ea System discharge. The sign is 9" x 6" x 1/16" (229 x152 x 1.6mm) and is constructed of white plastic with black lettering. The SystemDischarge Sign is located next to or under an audible or visual alarm outside of the protected space entrance(s). This sign, together with the alarm device(s) willalert personnel when HFC-227ea agent has discharged and allow them to takeappropriate actions.

Caution “Do Not Enter” Sign 02-10139

The purpose of the Caution Sign is to alert personnel that the room is protectedby an HFC-227ea System and that all doors should be kept closed in the event of fire. The sign is 10" x 13" x 1/16" (254 x 330 x 1.6mm) and constructed of yellow plastic with black lettering. The Caution Sign should normally be locatedon the entrance door(s) leading into any room where HFC-227ea protection isbeing provided.

Upon Device Activation "Exit" Sign 02-10105

The purpose of the System Discharge Sign is to explain the presence of an alarmin the event of an HFC-227ea System discharge. The sign is 9" x 6'' x 1/16" (229x 152 x 1.6mm) and is constructed of white plastic with black lettering. TheSystem Discharge Sign is located next to or under an audible or visual alarminside of the protected space. This sign, together with the alarm device, will alertpersonnel when HFC-227ea agent has been discharged and allow them to take

appropriate action.System Abort "Push and Hold" Sign 02-10106

The purpose of this System Abort Sign is to identify the presence of the HFC-227ea System Abort Station. The sign is 4" x 2.25" x 1/16" (102 x 57 x 1.6mm)and is constructed of red plastic with white lettering. The System Abort Station isdesigned to provide a manual means by which the HFC-227ea system actuationcircuit may be interrupted. The System Abort Sign should be located next to eachHFC-227ea Abort Station for quick positive identification.


Form No. C.1.10.01-3

HFC-227ea

EXTINGUISHING

SYSTEM RELEASE

HFC-227ea EXTINGUISHING

SYSTEM DISCHARGE ALARM

IF ACTIVE

DO NOT ENTER AREA

THIS AREA IS PROTECTED BYA

HFC-227ea EXTINGUISHING SYSTEM

DO NOT ENTER AREA DURINGOR AFTER DISCHARGE

KEEP DOOR CLOSED AT ALL TIMES

HFC-227ea EXTINGUISHING

SYSTEM ALARM

IF ACTIVE

EXIT AREA IMMEDIATELY

HFC-227ea

EXTINGUISHING

SYSTEM ABORT

PUSH AND HOLD


20/38


APPLICATION (Cont.)

System "Main/Reserve" Sign 02-10107

The purpose of Main/Reserve Sign is to identify the presence of the HFC-227ea

Main/Reserve Switch Station. The sign is 4” x 2.25” x 1/16" (102 x 57 x 1.6mm)and is constructed of red plastic with white lettering. The Main/Reserve Signshould be located under the Main/Reserve Switch for positive identification. AMain/Reserve Switch is used with systems that incorporate main and reserve (back up) HFC-227ea Agent storage.

Release Pending Sign 02-10268

The purpose of the Release Pending Sign is to explain the presence of an alarm inthe event of an impending HFC-227ea System discharge. The sign is 7” x 4.25” x1/16" (178 x 108 x 1.6mm) and is constructed of red plastic with white lettering.

The Release Pending Sign is located next to an audible or visual alarm inside of theprotected space. This sign, together with the alarm device, will alert personnel of aforthcoming HFC-227ea Agent discharge and allow them to take appropriate action.

HFC-227ea

EXTINGUISHINGSYSTEM

MAIN / RESERVE

HFC-227ea

RELEASE

PENDING WHENDEVICE IS ACTIVE

EXIT AREA


21/38

GAS CARTRIDGE ACTUATOR

DESCRIPTION

The Gas Cartridge Actuator (GCA), Fike P/N 70-1651, provides the necessary pressure to fully open all Fike's Clean Agent containers utilizing a Fike fast acting rupture disc assembly. The GCA consists of a stainless steel body containing twosets of bridge wires and a charge of smokeless powder. Operation of the GCAoccurs when an electric current is sent through the bridge wires causing thesmokeless powder to ignite. This generates the necessary pressure to open therupture disc and discharge the agent in the Clean Agent container.

The GCA is not an explosive device and cannot be used as a detonator.Operating time for the GCA is 10 milliseconds. Operating temperature range forthe GCA is +32o to +130oF. (0o to +54.4oC) for HFC-227ea systems. ForECARO-25 systems, the maximum operating temperature is 120oF (49oC).

The GCA is designed to operate in all Fike Clean Agent system containers with1" and 2 1/2" valves and also containers with 3" valves with single disc packs. This device is designed to operate by two methods of actuation:

1. Electrical input from a Fike Control Unit or Interface Firing Module (IFM)and through an Agent Release Module (ARM).

2. Input from an (optional) independent Fike Manual Actuator.

Installation

The GCA has two sets of threads; the 3/8-24 UNF-20 thread is used to installthe GCA in either 1 or 2 1/2" (25 or 65mm) valved containers and the 7/16-20UNF-24 thread is used to install the GCA in the 3" (80mm) valved containers, without modification to the valve assemblies.

It should be noted that for retrofit systems, the junction box for the ARM/GCA

may need to be longer and/or larger than was required for the ARM/detonatordevice.

Shelf Life

The GCA is a sealed device utilizing a glass seal and epoxy plug on the wire endand a mylar seal on the discharge end. This extends the actuator's continuousservice and shelf life to 10 years before it requires replacement.

Shipping Classification

The GCA will not detonate any explosive materials or products. It has a U.S.Department of Transportation classification of:

- Class: 1.4- Compatibility Group: "S"- Shipping Number: UN0323

This classification allows this device to be shipped on any type of carrier(excluding ocean containers) such as commercial airlines, as well as all forms of land carriers without special handling permits and/or licensing.


Gas Cartridge Actuator

APPROVALS

• UL Listed - Ex 4623• FM Approved:

• HFC-227EA: 0Y4A8.AF

• ECARO-25 TM: 3014476

Form No. C.1.26.01-2


22/38


GAS CARTRIDGE ACTUATOR DETAILS

.75" Hex

40" (1016mm) Ref. 3.5" (89mm)

Epoxy Plug3/8-24 UNF-2A Thread

for 1" (25mm) &

2-1/2" (65mm) ValvesSST Body

7/16-20 UNF-2A Thread

for 3" (80mm) Valves

#22 AWG Solid Copper

PVC Insulated Wires

ARM Wires (Red/Blue)

Manual Actuator Wires

(Yellow/Green)

YEL

GRN

REDBLUE

Fike

Control

Panel

ARM

GCA

Manual Actuator

GAS CARTRIDGE ACTUATOR DETAILS


23/38


24/38


25/38


26/38

The MSDS format adheres to U.S. standards and regulatory

requirements and may not meet regulatory requirements in

other countries.

This information is based upon technical information

believed to be reliable. It is subject to revision as

additional knowledge and experience are gained.

FE-227

6160FR Revised 22-SEP-2000 Printed 30-MAR-2001

CHEMICAL PRODUCT/COMPANY IDENTIFICATION

Material Identification

FE-227 is a registered trademark of DuPont.

CAS Number : 431-89-0

Formula : CF3 CHF CF3

Molecular Weight : 170.04

CAS Name : Propane, 1,1,1,2,3,3,3-Heptafluoro-

Tradenames and Synonyms

HFA 227ea

FC-227ea

Dymel 227 ea/p

2-Hydroperfluoropropane

Propane, 1,1,1,2,3,3,3-Heptafluoro-

HFC-227ea

2-Hydroheptafluoropropane

FM-200(tm) Great Lakes Chemical Corp.

Heptafluoropropane

Company Identification

MANUFACTURER/DISTRIBUTOR

DuPont

Fluoroproducts

1007 Market Street

Wilmington, DE 19898


27/38

PHONE NUMBERS

Product Information : 1-800-441-7515

Transport Emergency : CHEMTREC 1-800-424-9300

Medical Emergency : 1-800-441-3637

COMPOSITION/INFORMATION ON INGREDIENTS

Components

Material CAS Number %

1,1,1,2,3,3,3-Heptafluoropropane 431-89-0 99+

HAZARDS IDENTIFICATION

Potential Health Effects

Symptoms similar to oxygen deprivation (headache, nausea,

dizziness or loss of consciousness) may result from

overexposure by inhalation. Gross overexposure by

inhalation may cause irregular pulse, heart palpitations

and potentially fatal cardiac sensitization. Cold, white or

discolored skin or in severe cases blistering, can be a sign

of frostbite caused by cold liquids or gases.

Eyes: Direct eye contact with the liquid or cold gas can

cause chilling or possibly frostbite of exposed tissues.

Skin: Direct skin contact with the liquid or cold gas can cause chilling or possibly frostbite of exposed tissues.

Ingestion: Not expected to be a hazard in normal industrial

use.

Inhalation: Inhalation of high concentrations can be

harmful or fatal due to oxygen deprivation and/or heart

irregularities (arrhythmias). Misuse of product by

deliberately inhaling high concentrations of this gas could

cause death without warning.

Medical Conditions Aggravated by Exposure: Persons with

pre-existing cardiac, respiratory or central nervous system

disorders may be more susceptible to effects of an

overexposure.

Notice to Physicians: Overexposure to this material may

make the heart more susceptible to arrhythmias.

Catecholamines such as adrenaline and other compounds having

similar effects should be reserved for emergencies and then

used only with special caution.


28/38

Vapors are heavier than air and pose a hazard of suffocation

if trapped in enclosed or low places.

Carcinogenicity Information

None of the components present in this material at concentrations

equal to or greater than 0.1% are listed by IARC, NTP, OSHA or ACGIH

as a carcinogen.

FIRST AID MEASURES

First Aid

INHALATION

If inhaled, immediately remove to fresh air. If not breathing,

give artificial respiration. If breathing is difficult, give oxygen. Call a physician.

SKIN CONTACT

Treat for frostbite if necessary by gently warming affected area.

EYE CONTACT

In case of contact, immediately flush eyes with plenty of water

for at least 15 minutes. Call a physician.

INGESTION

Ingestion is not considered a potential route of exposure.

FIRE FIGHTING MEASURES

Flammable Properties

1,1,1,2,3,3,3-Heptafluoropropane is not flammable, however

in the presence of a flame or ignition source it may

decompose to form toxic hydrogen fluoride or carbonyl

fluoride.

Non-flammable.

Extinguishing Media

Use media appropriate for surrounding material.

Fire Fighting Instructions


29/38

Self-contained breathing apparatus (SCBA) may be required if

cylinders rupture or release under fire conditions.

Keep cylinders cool with water spray applied from a safe

distance.

ACCIDENTAL RELEASE MEASURES

Safeguards (Personnel)

NOTE: Review FIRE FIGHTING MEASURES and HANDLING (PERSONNEL)

sections before proceeding with clean-up. Use appropriate

PERSONAL PROTECTIVE EQUIPMENT during clean-up.

Evacuate personnel, thoroughly ventilate area, use self-contained

breathing apparatus. Keep upwind of leak - evacuate until gas has

dispersed.

Initial Containment

Use forced ventilation to disperse vapors.

HANDLING AND STORAGE

Handling (Personnel)

Do not breathe gas. Avoid contact with eyes, skin, or clothing.

Wash thoroughly after handling. Wash clothing after use.

Storage

Store in a well ventilated place. Store in a cool, dry place.

Keep container tightly closed.

EXPOSURE CONTROLS/PERSONAL PROTECTION

Engineering Controls

Use only with adequate ventilation. Keep container tightly closed.

Personal Protective Equipment

EYE/FACE PROTECTION

Wear safety glasses or coverall chemical splash goggles.

RESPIRATORS


30/38

Wear NIOSH approved respiratory protection, as appropriate.

PROTECTIVE CLOTHING

Where there is potential for skin contact have available and wear

as appropriate impervious gloves, apron, pants, and jacket.

Exposure Guidelines

Exposure Limits

FE-227

AEL * (DuPont) : 1000 ppm, 8 & 12 Hr. TWA

* AEL is DuPont's Acceptable Exposure Limit. Where governmentally

imposed occupational exposure limits which are lower than the AEL

are in effect, such limits shall take precedence.

PHYSICAL AND CHEMICAL PROPERTIES

Physical Data

Boiling Point : -15.6 C (3.9 F)

Melting Point : -133 C (-207 F)

Vapor Pressure : 66.69 psia @ 25 C (77 F) (460.06 kPa)

Liquid Density : 1.386 g/cm3 @ 25 C (77 F) (86.53 lb/ft3)

Critical temperature : 101.6 C (214.9 F)

Critical pressure : 424.7 psia (2930 kPa)

Odor : Slight Ethereal

Form : Liquified Gas

STABILITY AND REACTIVITY

Chemical Stability

Stable at normal temperatures and storage conditions.

Avoid sources of heat or open flame.

Incompatibility with Other Materials

Incompatible with strong reducing agents such as alkali

metals (e.g., sodium, potassium), alkali-earth metals (e.g.,

magnesium, calcium), and powdered aluminum or zinc.

Decomposition

Decomposes by reaction with high temperature (open flames,

glowing metal surfaces, etc.) forming hydrofluoric acid,

carbonyl fluorides, carbon monoxide and carbon dioxide.


31/38

Polymerization

Polymerization will not occur.

TOXICOLOGICAL INFORMATION

Animal Data

Groups of six rats were exposed for four hours to 25,000 or

53,000 ppm of FC-227ea. No deaths occurred. Signs of

toxicity during exposure included irregular breathing,

slight lacrimation and red ears. No toxic signs were seen

post exposure.

Animal studies have found the rat four hour LC50 to be

>788,696 ppm (80%), the highest level tested. A cardiac

sensitization study in dogs found the No Observable Adverse

Effect Level (NOAEL) to be 9.0%. The Lowest Observable Adverse Effect Level (LOAEL) for this study was reported to

be 10.5%. A 90 day inhalation study did not find any

exposure related effects at 105,000 ppm (10.5% vol./vol.),

the highest level tested.

Tests have shown that this material does not cause genetic

damage in bacterial and mammalian cell cultures. When

evaluated by an in-vivo mouse micronucleus assay, no

increase in micronuclei was observed.

DISPOSAL CONSIDERATIONS

Waste Disposal

Treatment, storage, transportation, and disposal must be in

accordance with applicable Federal, State/Provincial, and Local

regulations. Incinerate material in accordance with Federal,

State/Provincial and Local requirements.

TRANSPORTATION INFORMATION

Shipping Information

DOT

Proper Shipping Name : Heptafluoropropane

Hazard Class : 2.2

I.D. No. (UN/NA) : UN 3296

DOT Label(s) : Nonflammable Gas


32/38

REGULATORY INFORMATION

U.S. Federal Regulations

TSCA Inventory Status : Listed.

TITLE III HAZARD CLASSIFICATIONS SECTIONS 311, 312

Acute : Yes

Chronic : No

Fire : No

Reactivity : No

Pressure : No

OTHER INFORMATION

NFPA, NPCA-HMIS

NFPA Rating

Health : 1

Flammability : 0

Reactivity : 1

NPCA-HMIS Rating

Health : 1

Flammability : 0

Reactivity : 0

Personal Protection rating to be supplied by user depending on use

conditions.

Additional Information

Some of the health and toxicity information was provided

from a Great Lakes Chemical Corporation MSDS.

----------------------------------------------------------------------

The data in this Material Safety Data Sheet relates only to the

specific material designated herein and does not relate to use in

combination with any other material or in any process.

Responsibility for MSDS : MSDS Coordinator

> : DuPont Fluoroproducts Address : Wilmington, DE 19898

Telephone : (800) 441-7515

End of MSDS


33/38

T HE MO ST TR US TED

F I RE S UP PR ES SI O N S YS

ON THE MARKET

C L E A N A G E N T F I R E S U P P R E S S I O NC L E A N A G E N T F I R E S U P P R E S S I O N

CLEAN AGENT

FIRE SUPPRESSION

WITH


34/38

C LE AN A GE NT F IR E P RO TE CT IO N I S

BEST F OR EL ECTR ON IC S AN D HI GH

VAL UE ASSETS

Water-based fire suppression systems (i.e. sprinklers), are designed to

protect people and structures. But, when it comes to protecting high

value machinery, computers and other electronic equipment, water ca

be more damaging than the fire itself!

Gaseous chemical suppression systems (clean agent systems) have been

used for more than 40 years to protect electronics and other valuables tha

are susceptible to the damaging effects of water-based suppression

systems. Fike’s Clean Agent Systems are superior to water and dry chemic

in virtually every way:

Imagine your company’s valuable data, equipment and systems lost to f

It happens every day somewhere in the world. And it’s devastating. Eveone day lost to fire-related downtime can mean lost revenues, custome

and profits.

You can’t afford equipment being inoperable ... service interruptions to

customers ... or being unable to produce valuable data, documents and

resources. You must protect your employees, your business and most

importantly, your customers.

CONSIDER THE FIKE CLEAN AGENT FIRE SUPPRESSION SYSTE

IT’S TIME TO THINK

THE UNTHINKABLE.

WATER AND ELECTRONICS –

A BAD COMBINATION

• Clean agents are not electrically conductive, and donot damage electronics — water is a conductor and

ruins electronics!

• Clean agents are safe for people.

• Clean agents leave no residue and require no clean-up.

• Because they act quickly, clean agents greatly reduce the

amount of smoke and soot damage caused by a fire.

• Clean agents provide three-dimensional suppression,

extinguishing fires that water may not reach.

FM-200

Save lives

Protect high-value equipment,

assets and irreplaceables

from damage

Minimize business interruption

due to fire

Minimize downtime after fire

Prevent residue and clean-up

after fire

Minimize floor space requirements

The superior design features and

exceptional performance of Fike’s

Clean Agent Fire SuppressionSystem using DuPont™ FM-200®

help you:

C L E A N A G E N T F I R E S U P P R E S S I O N


35/38

WHY FM-200?

Fike’s Clean Agent System extinguishes a fire quickly by

discharging in 10 seconds – or less! The system removes

heat and breaks up the fire at the molecular level. FM-200

discharges as gas, leaves no residue and doesn’t require costly

clean-up, unlike sprinklers and other systems.

And with Fike’s patented valve system, we offer greater

coverage – faster and more effectively — than any other

option. This means minimal damages and interruptions

for your business.

FM-200 is a widely accepted replacement for Halon 1301.

FM-200 is people-friendly... won’t obscure vision in a

fire... and Fike’S Clean Agent System using FM-200 takes

up less floor space than other systems. In addition, the U.S.Environmental Protection Agency named it a non-ozone

depleting agent for fire extinguishing systems installed in

occupied spaces.

HE MOST TRUSTED FIRE SUPPRESSION SYSTEM ON THE MARKETHE MOST TRUSTED FIRE SUPPRESSION SYSTEM ON THE MARKET

For speed in suppressing fires, reducing

damages, saving on floor space and allowing visibility, Fike is the clear choice.

FIKE’S CLEAN AGENT SYSTEM WITH

FM-200 PROVIDES OPTIMUM FIRE

DAMAGE PROTECTION FOR CRITICAL

ASSETS IN NUMEROUS APPLICATION

• Telecommunications facilities

• Control rooms

• Computer rooms

• Data processing equipment

• Marine shipboard systems

• Record and archive storage

• Museums

• Universities

• Pharmaceutical and medical fac

• Industrial applications

PROTECTS YOUR PEOPLE, ASSETS AND BUSINESS



36/38

WHY FIKE?

W W W . F I K E . C O M

FIKE – THE FIRST CHOICE FOR KEY ASSET PROTECTION SINCE 1945

We manufacture the finest

products possible, your orders are filled quickly and you enjoy

24-hour technical support.

Our on-site manufacturing

and testing provides the

highest quality protection.

THE FIKE DIFFERENCE

Fike is the industry standard for performance...

unsurpassed for detection technology... and our

rupture valve unleashes protection the fastest.

We have more Clean Agent

experience than any other

company. Fike authorized

distributors are trained expertsin Clean Agent Suppression

Systems and can handle all your

needs quickly and efficiently.

You can’t afford a major – or even

minor – interruption due to fire. In

fire situations, every second counts.

In fact, downtime often outweighs

the loss of equipment and structures.For this reason, companies large and

small count on Fike.

We manufacture most of what we

sell. As a result, you’ll benefit from

Fike’s higher quality control with

both equipment and personnel ...

a greater capacity to meet your

demands quickly ... and shorter

lead times between your order

and the system’s installation.

Innovation is another key. At Fike,

we built our name on research,

development and testing of systems.

“Good enough” is never good

enough. We were the first company

to offer an independent laboratory

approvedFM-200 system.



37/38

ADVANCED DETECTION SYSTEMSFIKE LEADS THE WAY WITH CHEETAH Xi®. Our intelligent Cheetah Xi system performs operations with

speed, intelligence and flexibility. Fike can help you design the ideal fire protection, detection and

control system for your facility.

O NE PAN EL F IT S AL L Y OU R N EE DS F OR L IF E SAF ET Y AN D F IRE P RO TE CT IO N



38/38

E - m a i l : f p s s a l e s @ f i k e . c o m

Fike and Fike Corporation, CheetahXi are trademarks or registered trademarks of

Fike Corporation VESDA is a registered trademark of Xtralis DuPont and FM 200

F I K E G L O B A L M A N U F A C T U R I N G , S A L E S A N D S E R V I

AMERICAS

FIKE CORPORATIONBlue Springs, MOUSATel: +1-816-229-3405Email: [email protected]

FIKE LATINA LTDA

Jundiai, BrazilTel: +55-11-4525-5900Email: [email protected]

EUROPE

FIKE PROTECTION SYSTEMS, LTD.Guildford, SurreyUnited KingdomTel: +44-01-483-457-584Email: [email protected]

ASIAFIKE ASIA PACIFIC SDN BHDSelangor Darul Ehsan, MalaysiaTel: +60-3-7859-1462Email: [email protected]

EXPERIENCED: We’ve worked in the

ire protection business since 1960.

FOCUSED: We specialize in Life Safety

Products, as well as Facility and Asset

Protection Products.

VERSATILE: We design, manufacture,

distribute and maintain our products.

GLOBAL: We have clients, manufacturing

acilities, sales outlets and maintenance

ompanies around the world.

NNOVATIVE: In 1994, we became

he first manufacturer to bring a

UL-listed and FM-approved, clean agent

ire-suppression system to market,

eplacing Halon.

EARTH-FRIENDLY: We pioneered the

development of clean agent systems

nd we continue to develop other

nvironmentally safe alternatives such

s our superior inert gas system.

COMPREHENSIVE: Fike has a worldwide

etwork of experienced distributors

ach with a staff of factory trained

echnicians to meet your installation

nd service requirements.

WE ’RE PROU D

OF OUR RE SUME

Printed on 25% post consumer fiber / 50% total recycled content with soy based inks.

T H E M O S T T R U S T E D

F I R E S U P P R E S S I O N S Y S T E M

O N T H E M A R K E T

Documents

Fike Agent Storage Containers