PRECAUTIONERY STATEMENTSCAUTION: HAZARDOUS TO HUMANS AND DOMESTIC ANIMALSCauses eye irritation. Harmful if swallowed or absorbed through skin. Avoid contact with skin, eyes or clothing. Wear protectiveclothing such as gloves, long-sleeved shirt, long pants and hat. Harmful if inhaled. Do not breath vapor, spray mist, or dust. Whilespraying paint , sanding or sandblasting, wear a mask or respirator approved by the National Institute for Occupational Safetyand Health. Remove contaminated clothing and wash before reuse. Wash thoroughly with soap and water after handling.

KEEP OUT OF REACH OF CHILDREN!FIRST AID: If swallowed: 1.) Call a poison control center or doctor immediately for treatment advice. 2.) Have person sipa glass of water if able to swallow. 3.) Do not induce vomiting unless told to do so by a Poison Control Center or doctor.4.) Do not give anything by mouth to an unconscious person. If on skin or clothing: 1.) Take off contaminated clothing.2.) If on skin wash with plenty of water for 15-20 minutes. 3.) Call poison control center or doctor for treatment advice.If inhaled: 1.) Move person to fresh air. 2.) If person is not breathing, call 911 or an ambulance, then give artificial respiration,preferably mouth-to-mouth if possible. 3.) Call poison control center or doctor for treatment advice.If in eyes: 1.) Hold eye open and rinse slowly and gently with water for 15-20 minutes. 2.) Remove contact lenses, if present,after the first 5 minutes, then continue rinsing eye. 3.) Call a poison control center or doctor for treatment advice.Other: Have the product container or label with you when calling a poison control center or doctor or going for treatment.Note to Physician: Probable mucosal damage may contra-indicate the use of gastr ic lavage.

PRODUCT EMERGENCIES: 1-800-424-9300ENVIRONMENTAL HAZARDS: This pesticide is toxic to aquatic organisms including fish and shellfish. Do not apply directlyto water by cleaning of equipment or disposal of wastes. Do not allow chips and dust generated during paint removal to enterwater. Dispose of paint debris in an approved landfill. Do not discharge effluent containing this product into lakes, streams,ponds, estuaries, oceans or public waters unless this product is specifically identified an addressed in an NPDES permit. Donot discharge effluent containing this product to sewer systems without previously notifying the sewage treatment plantauthority. For guidance contact your state water board or regional office of the EPA.

STORAGE AND DISPOSAL: Do not contaminate water, food or feed by storage or disposal. Store in cool dry area awayfrom heat or open flame. Keep from freezing. Open dumping is prohibited.

PESTICIDE DISPOSAL: Pesticide wastes are toxic. Paint that cannot be used according to label instructions must be disposedof according to federal, state or local procedures.

CONTAINER DISPOSAL: Do not reuse this container. Replace lid and disposeof in a sanitarylandfill or by other approved State and Local procedures.

DISCLAIMER: The performance of any marine paint or coating depends on manyfactors outside the control of Flexdel Corp. including environmental conditions.Therefore, Flexdel Corp. cannott guarantee this product’s suitability for your particularpurpose of application. Implied warranties of fitness for particular purpose and ofmerchantability are excluded. Flexdel Corp. shall not under any circumstances, beliable for incidental or consequential damages. By purchase or use of this product,buyer agrees that sole and exclusive remedy, if any, is limited to the refund of thepurchase price or replacement of the product at Flexdel Corp., option.

DIRECTIONS FOR USEThis is a cuprous oxide pigmented coating, formulated especially to prevent theattachment of both plant and animal fouling on vessels immersed in both seawater and“brackish” water.

1A) Surface preparation: New / Bare Fiberglass Hulls: Wipe down surface withAquagard 180 Wash & Dewaxer. Change rags frequently to assure complete removalof wax and mold release agent and contaminates. Sand surface thoroughly with 80 or100 grit sand paper. Wipe down surface again with Aquagard 180 Wash & Dewaxerto remove sanding residue and immediately apply one (1) coats of Aquagard 181 Primerwith a roller or brush. Allow Primer to dry for minimum of two (2) hours.

1B) Surface preparation: For previously painted surface: To prepare the surfacefor coating, remove all loose coating and fouling residue by either washing with highpressure water, scraping or by sanding. Apply a small patch of Aquagard WaterbaseAntifouling Bottom Boat Paint to test compatibility with the old paint. If AquagardWaterbase Antifouling Bottom Boat Paint cracks or lifts, all the old paint will have tobe removed. Then follow the “Bare Fiberglass Hulls” system specified above. If nothingappears to happen when this product is applied, let the test patch dry for several hoursand then scrape this product to see if it is adhering to the old paint satisfactorily. Ifthe adhesion looks good, sand the entire surface thoroughly with 80 grit sandpaper.

Previously painted surfaces in poor condition (such as chipping, peeling or flaking) shouldbe stripped to bare fiberglass. Then proceed with the “Bare Fiberglass Hulls” preparation.

2) Application: A clean dry surface (free of scale, corrosion, dirt, grease, oil, marinefouling, or other foreign matter) will provide the optimum performance of this coating,when used for either complete coating or touch-up. Wipe down surface with Aquagard180 Wash & Dewaxer. Inadequate surface preparation will result in unsatisfactoryperformance. Mix the coating thouroughly for a minimum of five (5) minutes to insurecomplete pigment reincorporation. Apply by either brush, roller or spray. AquagardWaterbase Antifouling Bottom Boat Paint should be applied at or above 50°F. Applytwo (2) coats of Aquagard Waterbase Antifouling Bottom Boat Paint. Allow four (4)hours drying time between coats. Let final coat dry eight - twelve (8-12) hours beforelaunching the boat. The theoretical coverage of this product is approximately 400 squarefeet per gallon. Clean up with water when finished.

1 US Quart / 946 ml

for Fiberglass & Wooden Boats

Ablative Action RepelsBarnacles & Other GrowthWater Based Paint Rolls On EasilySoap & Water Clean-upNon-Toxic Fumes

WARNING! Keep out of reach of children. See reverse side for additional safety information.

EPA Reg. No. 9339-19-70383EPA Est. No. 9339 NJ01

Fiberglass & Wooden Boats

Ablative Action RepelsBarnacles & Other GrowthWater Based Paint Rolls On EasilySoap & Water Clean-upNon-Toxic Fumes

©2007, Manufactured for Flexdel Corporation1969 Rutgers University Blvd., Lakewood, NJ, USA

888.353.9335 aquagard-boatpaint.com

Made in U.S.A. Printed in U.S.A.

FLEXDELACTIVE INGREDIENTS: Cuprous Oxide ..........26.37%INERT INGREDIENTS......................................73.63%(Copper as Metallic – 22.68%)

Total ..............................................................100.00%