Upload
mauricio-j-gongora
View
327
Download
4
Embed Size (px)
Citation preview
GARAGE DOOR SUPPLIES
When Quality & Service Matter ...
ewww.fehr.comOrder by
Phone: 800.431.3095 Fax: 888.352.1790or Online
Phone: 800-431-3095 • 845-246-9525
Product Index
Angle Shear .............................................22
Bearing Plates ..........................................30
Brackets Bottom Brackets ...................................... 11 Top Brackets ............................................ 11
Cable .......................................................33
Cable Assemblies Extension Cables .....................................38 Spring Containment Cables ......................38 Torsion Cables .........................................37 Truck Door Cables ...................................44
Cable Accessories Thimbles ................................................ 34 Wire Rope Clips ...................................... 34 Cable Spools ........................................... 34 Cable Cutters ...........................................36 Swaging Tools .........................................36 Cable Sleeves & Stops ...............................35
Cable Puller .............................................34
Chain Hoists .............................................31
Cones & Drums .........................................29
Couplers ...................................................29
Deadbolts .................................................15
Decorator Angle .......................................31
Disconnect Devices ...................................14
Electrical Cords ........................................13
Fasteners ............................................. 40-41
Handles Lock Handles ..........................................15 Lift Handles ............................................16
Hardware Kits Fastener Bags ........................................39
Lock Bags .................................................17
Hinges ................................................... 9-10
Jamb Brackets ..........................................31
Key Switch ...............................................14
Lift Handles .............................................16
Locks Lock Handles ..........................................15 Rim Cylinders & Deadbolts .......................15 Side Locks ...............................................16 Spring Latches .........................................17 Lock Bars ................................................18 Lock Packages .........................................17
Low Headroom Hardware .........................14
Lubricants ................................................42
Nails ........................................................20
Nylon Rope ................................................ 9
O&E Kits ..................................................14
Operator Reinforcing Brackets ..................13
Perforated Angle ......................................22
Pulleys .....................................................28
2
Icon KeyThroughout the catalog, the following icons will provide additional, important information relating to specific products.
Provides additional information for specific products.
Product Information
Details choices for a particular product other than those listed in the charts.
OptionsCalls your attention to warnings specific to the adjacent products.
Safety Alert
Fax: 888-352-1790 • 845-246-3330
Quick Close Fixtures .................................14
Rollers ....................................................7-8
Scrubs® Cleaner ........................................42
Sheaves ....................................................28
Shaft Coupler ...........................................29
Side Locks ................................................16
Sleeves .....................................................35
Slipit® Lubricants .....................................42
Springs Torsion Springs ...................................23-26 High Cycle Torsion Springs .......................25 Extension Springs ....................................27 Lock Bar Spring .......................................18
Spring Bumpers ....................................... 31
Spring Repair Block ................................ 24
Spring Fittings ..........................................29
Spring Latches and Sets ............................17
Step Plates ...............................................16
Stops ........................................................35
Swage Fittings .........................................35
Swaging Tool Kit ......................................35
Swivels .....................................................18
Terms & Conditions ................................... 4
Thimbles ..................................................34
Tools ........................................................36
Torsion Spring Safety Collar ......................25
Truck Door Hardware .......................... 43-44
Warnings & Cautions ................................. 4
Weatherseal ........................................ 20-21
Winding Bar ............................................34
Wire Rope Clips .......................................34
White Powder Coated Hardware ...............12
Zap Jackshaft Operators Residential & Commercial Operators .........46 Heavy Duty Commercial Operators ...........47 Battery Back Up, Autolock .......................47 Operator Covers ..................................46-47 Photo Cell, Antennae, Radio Receiver ........48 Motor Cable, Super Grip Transmitter .........48
To Place Your Order...For your convenience, we have provided a number of ways to order from us:
Phone: 800-431-3095 or 845-246-9525Fax: 845-246-3330 or 845-247-8300
Toll Free Fax: 888-352-1790Online: www.fehr.com
Fast Find
3
Free Freighton orders over
$250.00
Minimum Order$50.00
$$ SAVE $$
TERMS AND CONDITIONS OF SALE
Warnings, and Cautions Governing the Sale and Use of Cable, Springs and AttachmentsAll products are sold subject to the following Warnings and Cautions and with the express understanding that the purchaser and/or user are thoroughly familiar with their proper use. Fehr Bros. Industries, Inc. assumes no responsibility for the use, misuse or misapplication of its products.
WORKING LOAD LIMIT:The Working Load Limit (WLL) is the maximum load which should be applied to the product under any condition. WLL is based on a load being uniformly applied in a straight-line pull. It is the responsibility of the ultimate user to determine a WLL for each application. Many factors should be considered: including, but not limited to, loads applied, speed of operation, acceleration, length of cable, shock loads, abrasion, corrosion, size, condition of drums and sheaves, and the danger to life and property should a cable break.
BREAKING STRENGTH:Breaking Strengths apply only to new, unused Aircraft Cable. Do NOT use Breaking Strength for design or rating purposes. Use Working Load Limit instead.
MARKING REQUIREMENTS:U.S. Customs Law requires that the end user of imported products be informed of the country of origin. All im ported products sold by Fehr Bros. are marked accordingly. Resellers are responsible to relay country of origin infor mation to the end user.
WARNING:Garage Door Cables, Springs, and attachments are under significant load and installations, adjustments and replacements should be performed only by a trained professional. Spring containment cables should be used in conjunction with Extension Springs. Aircraft Cables are not suitable for use in aircraft controls.
AVOID SHOCK LOADS:Loads exceeding the static load caused by rapid change of movement. WLL will not apply.
INSPECTION:No product can operate indefinitely at its rated capacity. Cables must be lubricated and maintained in accordance with normal safety standards. Do not kink, knot or crush. Cable must be inspected regularly for any deterioration which may result in the loss of original strength. User must determine whether further use of the cable would constitute a safety hazard to life or property.
WARNING AND CAUTIONS
www.garagedoorsupplies.com4
PRICES: Prices are subject to change without notice. Invoices will be based upon prices in effect at time of shipment. Check our website for up to date pricing.
TERMS OF PAYMENT: VISA, MasterCard and American Express accepted. Net Cash 10 days for approved accounts.
MINIMUM INVOICE: $50.00, FOB Saugerties, NY
LATE CHARGE: A late charge of 1.5% per month will be added to accounts over sixty (60) days from date of invoice.
RETURNED CHECKS: A $30.00 fee will be charged for returned checks.
FREIGHT POLICY: Fehr saves you a freight bill. All materials are shipped FOB Shipping Point, Freight Allowed and Prepaid on single shipments of $250 or more within the continental United States. All other shipments are FOB Shipping Point, Freight Collect. Fehr Bros. Industries, Inc. reserves the right to ship by carrier of our choice. Freight paid orders may be subject to a Fuel Service Surcharge.
COD fees, redelivery, inside delivery, lift gate, call for appointment, over length, residential delivery, airfreight charges and any other special handling or packaging charges are the respon sibility of the customer.
Bills of lading must be signed with exception for missing
goods or exposed damages. Freight claims for damaged or missing materials are the responsibility of the buyer.All cartons must be inspected for concealed damage or shortage upon receipt. Claims must be submitted to the carrier within five business days.
RETURNS: Fehr Bros. wants you to be 100% satisfied with our products and service. Merchandise in its original condition may be returned for credit within thirty (30) days of receipt of material. Our Customer Service Department will provide a Return Material Authorization (RMA) form and number on request. Call 800-431-3095. Affix the RMA number labels to the outer carton and return the form with the material, freight paid, to the warehouse indicated on the RMA instructions.
A restocking fee of 15% plus freight charges will apply. No freight collect or COD shipments will be accepted. Unauthorized shipments will be returned at the customer’s expense. Special order material and material cut to custom specifications are not returnable.
WARRANTY: Fehr Bros. Industries, Inc. warranties its products against defective materials and workmanship at time of shipment. Damage in transit is the responsibility of the carrier. Claims are subject to inspection by our authorized representative, and liability is limited to replacement of material or refund of the purchase price. We cannot be responsible for labor charges and consequential damages.
_________________ ___________________________________ _______________________________________________
F A X O R D E R F O R M
FAX TO: 888-352-1790 ATTN:_______________________
CUSTOMER ID#_______________________________
BILL TO: _________________________________________________ SHIP TO: __________________________________________________
_________________________________________________ __________________________________________________
_________________________________________________ __________________________________________________
_________________________________________________ __________________________________________________
FEHR BROS. INDUSTRIES, INC. 895 Kings Hwy • Saugerties, NY 12477-4356
Fax 845.246.3330 or 845.247.8300 E-mail: [email protected]
Quantity Part# Description Unit Price
�Visa � Mastercard
�American Express
Credit Card #____________________________________________ Exp. Date ____/____
Name as it appears on card ___________________________________________________
Security Code _______
Date Customer P.O.# Purchasing Authorization
ewww.fehr.com
Fax: 888-352-1790 • 845-246-3330 7
2" Rollers
ROLL26XL
ROLL26L
ROLL4
2" Steel RollersPart# DescriptionROLL6 2" Frantz Type w/ 5/16"diameter Stem
ROLL9/DP 2" 7 Ball Steel w/ 4" Stemrating: 35 lb load, 10,000 cycles 8' door
ROLL4/DP 2" 10 Ball Steel w/ 4" Stemrating: 75 lb load, 15,000 cycles 12' door
ROLL26L/DP 2" 10 Ball 7" Long Stemrating: 75 lb load, 15,000 cycles 12' door
ROLL26XL/DP 2" 10 Ball 9" XL Stem rating: 75 lb load, 15,000 cycles 12' door
ROLL6
• Fehr's 26NL and Capped rollers have a redesigned bearing raceproviding for a higher load rating and extended cycle life.
• Capped rollers have a Solid Nylon Cap on the roller face and aNylon seal on the backside protecting the bearings from dust, dirt and moisture.
• Pre-lubricated with low temperature grease for long life.
ROLL26NL
2" Nylon RollersPart# Description
ROLL8/DP 2" Bearingless Nylon w/ 4" Stemrating: 50 lb load, 10,000 cycles 8' door
ROLL26NL 2" 10 Ball Nylon w/4" Stemrating: 125 lb load, 20,000 cycles 12' door
ROLL26NL-XL 2" 10 Ball 7" Long Stem Nylonrating: 125 lb load, 20,000 cycles 12' door
ROLL26NL-XXL 2" 10 Ball 9" XL Stemrating: 125 lb load, 20,000 cycles 12' door
ROLL9 ROLL8ROLL4
ROLL26NL-XXL
ROLL26NL
2" Capped Nylon RollersPart# Description
ROLL26CAP 2" 10 Ball Capped & Sealed w/ 4" Stemrating: 125 lb load, 20,000 cycles 12' door
ROLL26CAP-XL 2" 10 Ball Capped 7" XL Stemrating: 125 lb load, 20,000 cycles 12' door
ROLL26CAP
Product Information
Phone: 800-431-3095 • 845-246-9525
3" & Car Wash Rollers
• Ideal for marine and high corrosion environments, e.g. car wash and washdown applications.• Stainless Steel shafts and precision sealed bearings for corrosion resistance.
3" Steel Rollers
Part# DescriptionPcs/Ctn
ROLL27/DP3" 10 Ball 4" Stemrating: 150 lb load, 50,000 cycles 12' door
24
ROLL28/DP3" 10 Ball 7" Long Stemrating: 150 lb load, 50,000 cycles 12' door
24
ROLL28XL/DP3" 10 Ball 9" XL Stemrating: 150 lb load, 50,000 cycles 12' door
24
8
3" Nylon Rollers Precision BearingsPart# Description
ROLL27NL3" Nylon 4" Stem w/Precision Bearingrating: 150 lb. load, 100,000 cycles 12' door
ROLL27NL-XL3" Nylon 7" Long Stem w/Precision Bearingrating: 150 lb. load, 100,000 cycles 12' door
ROLL27NL-XXL3" Nylon 9" XL Stem w/Precision Bearingrating: 150 lb. load, 100,000 cycles 12' door
ROLL28XL
ROLL28
ROLL27
ROLL27NL
ROLL27NL-XL
ROLL27NL-XXL
Part# Description
ROLL512" Precision Bearing 5-1/4" Stemrating: 150 lb load, 100,000 cycles 12' door
ROLL522" Precision Bearing 8-1/4" Stemrating: 150 lb load, 100,000 cycles 12' door
ROLL533" Precision Bearing 5-1/4" Stemrating: 150 lb load, 100,000 cycles 12' door
ROLL543" Precision Bearing 8-1/4" Stemrating: 150 lb load, 100,000 cycles 12' door
Stainless Steel High Cycle Rollers Sealed Bearings
ROLL51
ROLL52
ROLL53
ROLL54
Product Information
Fax: 888-352-1790 • 845-246-3330
Hinges
18 gauge HingesPart# Pcs/CtnGDHINGE 18-1/DP 50
GDHINGE 18-2/DP 50
GDHINGE 18-3/DP 50
GDHINGE 18-4/DP 50
14 gauge HingesDealer Packs Bulk
Part# Pcs/Ctn Pcs/CtnGDHINGE 14-1 50 100
GDHINGE 14-2 25 75
GDHINGE 14-3 25 75
GDHINGE 14-4 25 75
GDHINGE 14-5 25 75
11 gauge HingesPart# Dealer Packs
Pcs/CtnBulk
Pcs/CtnGDHINGE11-1/DP 24 100
GDHINGE11-2/DP 12 75
GDHINGE11-3/DP 12 75
GDHINGE11-4/DP 12 75
GDHINGE11-5/DP 12 75
GDHINGE11-6/DP 12 75
GDHINGE11-7/DP 12 75
GDHINGE11-8/DP 12 75
GDHINGE11-9/DP 12 75
9
See our line of White Powder Coated Hinges on Page 12
Nylon RopePart# Description Length/ReelNR4X1000 1/8" Nylon Braided Cord 1000 ft
NR6X1000 3/16" Nylon Braided Cord 1000 ft
GDHINGE11-1
18-1
14-1
Phone: 800-431-3095 • 845-246-9525
Hinges
10
Narrow Rail HingesPart# Description Pcs/CtnGDHINGE 16-N 16 Ga. Narrow Rail Hinge 50
Adjustable Hinges for pinch resistant designs
Part# Description Pcs/CtnPPHINGE-SB 14 Ga. Hinge Base 50
PPHINGE-SA 11 Ga. Hinge Arm w/ Roller Carrier 50
Truck Door HingesPart# Description Pcs/CtnT69035 End Hinge 50
T61196 Center Hinge 100
T69035 T61196
PPHINGE-SB PPHINGE-SA
GDHINGE16-N
• Truck door hinges are black CED coated
Fax: 888-352-1790 • 845-246-3330
BBNLHR
Bottom Brackets
BB3M
BB1M
LHRXLCOMBRAC
11
Top & Bottom Fixtures
Part# Description Gauge Pcs/CtnRESBRAC/DP Residential Top Bracket 16 24
COMBRAC/DP Commercial Top Bracket 12 24
LHRCAR/DP Low Head Room 4" Top Roller Carrier 12 24
LHRXL/DP Low Head Room 8-3/4" XL Top Roller Carrier 12 24
Part# Description Gauge PinPrs/ Ctn
BB1M/DP Residential Bottom Bracket 13 Milford 25
BB3M/DP HD Residential Bottom Bracket 12 Milford 12
BB5/DP LHR Bottom Bracket 11 Clevis 12
BBNLHR/DP LHR Adjustable Bottom Bracket 12 Milford 6
BB12/DP Commercial Bottom Bracket 12 Clevis 12
BB7/DP HD Commercial Bottom Bracket 11 Clevis 12
BB9/DP Commercial Btm Bracket-3" Track 11 Clevis 6
BB5
BB12
BB7
BB9
Top Brackets
RESBRAC LHRCAR
Phone: 800-431-3095 • 845-246-9525
Operator Hook Up Brackets, Angle & Kits White Powder Coated
Premium White Powder Coated Hardware
Powder Coated Hardware
12
• HKIT-9W includes hinges, top and bottom brackets, capped nylon10 ball rollers, 2 lift handles and fasteners.
Part# DescriptionGDHINGE14-1W 14 Ga. #1 White Powder
GDHINGE14-2W 14 Ga. #2 White Powder
GDHINGE14-3W 14 Ga. #3 White Powder
GDHINGE14-4W 14 Ga. #4 White Powder
RESBRACW Residential Top Bracket
BB1MW Residential Bottom Bracket
ILSWIVW Inside Lock Swivel
LATCHW Spring Latch
N/HANDLEW Cushion Grip Lift Handle
Part# Description Pcs/CtnPERF12-8.25W 12 Ga. Perforated Angle 1
ORB20W/DP 20" Narrow Operator Bracket - 16/ctn 16
ORB21W/DP 21" Std. Operator Bracket - 12/ctn 12
HKIT-9W White Hardware Kit for Single Wide Door 1
Product Information
Fax: 888-352-1790 • 845-246-3330
Operator Reinforcement Brackets
QWIK
ORB18/21/24
LHROEKIT
• Quick Close Fixtures reduce headroom up to 3-1/2”.• O&E Kits require a minimum of 7” headroom.
Operator Accessories
13
Part# Description Pcs/CtnQWIK/DP Quick Close Fixture 10 Pcs
LHROEKIT O&E Low Headroom Kit 1 Pair
Part# Description Pcs/CtnORB20W/DP 20" Adj. Narrow Operator Reinforcing Bracket - White 16
ORB18/DP 18" Operator Reinforcing Bracket, 1 pc. design, 12 gauge - Zinc 12
ORB21/DP 21" Operator Reinforcing Bracket, 1 pc. design, 12 gauge - Zinc 12
ORB21W/DP 21" Operator Reinforcing Bracket, 1 pc. design, 12 gauge - White 12
ORB24/DP 24" Operator Reinforcing Bracket, 1 pc. design, 12 gauge - Zinc 12
ORBADJ/DP Adjustable Operator Reinforcing Bracket with Full Hinge - Zinc 15
UL® Approved Extension Cords Part# Description Gauge/LengthELC16/3X025 SPT Orange Extension Cord 16/3 x 25 ft
ELC14/3X003 SPT Beige Extension Cord 14/3 x 3 ft
ELC14/3X006 SPT Beige Extension Cord 14/3 x 6 ft
ELC14/3X009 SPT Beige Extension Cord 14/3 x 9 ft
ORB20W ORB21W ORBADJ
Product Information
Phone: 800-431-3095 • 845-246-9525
EKIT-101
Key Switch & Disconnect Devices
EKIT-100
LHRXL
BBNLHR
Part# DescriptionEKIT-100 Metal Key Switch, 15' Wire
EKIT-101 Keyed Disconnect Device, w/5' Cable
Low Headroom Hardware
QWIK
LHROEKIT
Part# Description Pcs/CtnLHRCAR/DP Low Headroom 4" Top Roller Carrier 24
LHRXL/DP Low Headroom 8-3/4" XL Top Roller Carrier 24
BB5/DP LHR Bottom Bracket w/ Outside Hookup 12 Pair
BBNLHR/DP LHR Bottom Bracket w/ Adjustable Roller Carrier 6 Pair
QWIK/DP Quick Close Fixture 10
LHROEKIT O&E Low Headroom Kit 1 Pair
Low Headroom Hardware
BB5
• Quick Close Fixtures reduce headroom up to 3-1/2”.• O&E Kits require a minimum of 7” headroom.
LHRCAR
14
Product Information
Fax: 888-352-1790 • 845-246-3330
• Locks available keyed alike or keyed randomly. Specify when ordering.
LS68
LS3L
LS7
LS3LSP
LS2S
LS3
LS3B
LS42
• Mounting hardware included.
15
Locks & Handles
Lock Handles
Part# DescriptionMounting
Hardware Included Pcs/CtnLS2S Plain T-Handle Set X 10
LS3 Locking T-Handle Set X 10
LS3B Blind Mount Locking T-Handle Set X 10
LS3L Locking L-Handle -- 10
LS3LSP L-Handle with Cylinder X 10
LS7* Rim Cylinder X 10
Deadbolt LocksPart# Description Pcs/CtnLS42 Stamped Deadbolt Cylinder Set 10
LS68 Cast Deadbolt Cylinder Set 10
LS-68-MK Cast Deadbolt Set - Master Keyed 10
* Also available in Brass (#LS82A)
Product Information
Options
Phone: 800-431-3095 • 845-246-9525
See complete Lock Packages on page 17
Locks & Handles
16
Rolled Grip
Part# Description Pcs/PackRGHANDLE/DP Rolled Grip Lift Handle 50
N/HANDLE/DP Cushion Grip Lift Handle 50
N/HANDLEW/DPCushion Grip Lift HandleWhite Powder Coated
50
Lift Handles
Cushion Grip
Step PlatePart# Description Pcs/PackSTEP/DP Step Plate 11 ga. 50
Step Plate
LS146
Side LocksPart# Description Bulk CtnLS146 Side Lock for 2" Track 100
LS147 Universal Side Lock for 2" or 3" Track 100
LS6R Locking Side Latch Mechanism 100
LS6R
LS147
Fax: 888-352-1790 • 845-246-3330
Lock Packages
Snap Latch Installation
• Includes handle, inside swivel, latch set w/chain and mounting fasteners.
• Also available with lock cable.
• Includes handle, inside lock, lockbar guide, spring and mounting fasteners.
• Lock bars and discs are sold separately.
Lock Packages & Lift Handles
17
Lock Bar Installation
Handle StyleFits Door
WidthLock 1 Side Lock 2 Sides
Part# Part#
Locking-T9' LS3-9S LS3-9D
16' LS3-16S LS3-16D
Blind Mount Locking-T
9' LS3B-9S LS3B-9D
16' LS3B-16S LS3B-16D
Locking-L9' LS3L-9S LS3L-9D
16' LS3L-16S LS3L-16D
Handle Inside Lock Part#Plain-T Cast Deadbolt LS2S-KIT
LS3LSP LS6R Latch LS3LSP-KIT
• Locks available keyed alike or keyed randomly. Specify when ordering.
Part# Description Pcs/PackLATCH/DP Spring Latch 50
STRIKER/DP Striker Plate 50
LATCHSET9Single Spring Latch Set
w/ Chain for 9ft. Door10
LATCHSET9DDouble Spring Latch Set
w/Chain for 9 ft. Door10
LATCHSET16Single Spring Latch Set
w/Chain for 16 ft. Door10
LATCHSET16DDouble Spring Latch Set
w/Chain for 16 ft. Door10
EGSASH8X500 #8 Sash Chain - Zinc Plated 500 ft/reel
EGSH125/DP 1/8" x 1" S-Hook - Zinc Plated 100
Spring Latch Sets & Hardware
Striker Plate
• Also available White Powder Coated. See pg A6
Product Information
Product Information
Options
Spring Latch
Spring Latch Set
Phone: 800-431-3095 • 845-246-9525
Best Freight Policy in the Industry$250.00 Orders – Freight Prepaid
18
Lock Hardware
Inside SwivelLock Bar Guide
#1 Lock Bar Disc
Inside Rigid Lock Handle
Lock BarLock Bar Spring
#5 Lock Bar Disc
Formed Latch Bar
Swivels and Lock BarsPart# Description Pcs/PackILSWIV Inside Swivel 10
IRHANDLE/DP Inside Rigid Lock Handle - Square Position 10
FORMBAR/DP Formed Latch Bar - Square Position 10
LB50 50" Lock Bar for 8 ft. Door 10
LB52 52" Lock Bar for 8-1/2 ft. Door 10
LB55-7/8 55-7/8" Lock Bar for 9' Door 10
LBD5 #5 Lock Bar Disc Square Position 10
LBD1 #1 Lock Bar Disc Square Position 10
LBS360/DP 3" Lock Bar Spring 100
3GUIDE/DP #3 Lock Bar Guide 100
• Also available WhitePowder Coated.See page A6
Fax: 888-352-1790 • 845-246-3330
���������������������������
• Weatherseal, The Best from the Best! Fehr Bros teams up with Royal Mouldings® (Marley) to supply the highest quality perimeter seal available. Manufactured using impact modifiers and anti-weathering agents for color retention. Available in 5 styles, 8 lengths and 6 colors. Additional items and colors are available as a direct shipment. See pg. 20 & 21
• Operator Reinforcement Brackets. Expanded line includes a versatile narrow body bracket that works on both 18" and 21" panels. See pg. 13.
• Capped Rollers have a redesigned bearing race for improved performance. With a full nylon face cap and rear seal to keep the dirt and dust out, these rollers will outlast any in their class. See pg.7
Featured Products...
• Perforated Angle Iron. We've got all the angles covered with an expanded selection of
gauges and sizes to meet both your residential and commercial needs. Available in electrogalvanized and powder coated in gray or white. See pg. 22.
• Zap Jackshaft Operators These compact, lightweight and powerful operators are designed for easy use. ZAP operators work on single phase power and there is no need for limit switches. The built in safety features are a big plus.See the line on pages 46-48
21" panels. See pg. 13.
Phone: 800-431-3095 • 845-246-9525
Weatherseal
Royal Mouldings® Weatherseal
• Standard lengths in 7, 8, 9, 10, 12, 14, 16 and 18 ft.
• Additional colors available as factory direct shipments include Bronze, Red-Brown, Bright White, and Terratone.
• Anti-weathering agents for superior color retention.
• Formulated with impact modifiers. Predrilling is not required. Predrilled material is available as factory direct.
• Packed 15 pcs per carton except where noted.• Factory direct shipments (DS) are subject to
minimum requirements.
Brickmold & Door Surround & Trim Planks
WS2448
20
Part# Description Pcs/CrateWS7318 4" Trim Plank (3/4" x 3-1/2") 150
WS7311 6" Trim Plank (3/4" x 5-1/2") 90
WS7312 8" Trim Plank (3/4" x 7-1/2") 60
WS2497 Door Surround (16' long) 144
WS2448 Brick Mold (17' long) 216
WS2497
Aluminum Nails • Extra strong tempered aluminum alloy.• Will not red rust or stain.• Complies with F.H.A. requirements.
Style Description White Almond Sandstone Brown H.Green Grey
WS2213 2" Wide w/ Side FlapAll Std. Lengths
7',8', 9',16'
7',8', 9',16'
7',8',9', 10',12',16'
7',8', 9',16'
7',8', 9',16'
WS2211 2" Wide w/Top FlapAll Std. Lengths
7',9',16' 7',9',16'7',8', 9',16'
DS DS
WS2016 1-7/8" Wide w/Side Flap DS DS DS DS DS DS
WS2100 1-7/8" Wide w/Top Flap DS DS DS DS DS DS
• Never Rot Premium PVC extruded millwork.• Replacement or new installations.• These items are available as factory direct shipments only.
Minimums apply.
Style Description Packing/Ctn.WS2591 3-1/4" Wide w/Top Flap - White 16' (5 pcs/carton)
WSNAILAluminum Nails 1-1/4" Length Available in White, Brown, Almond, Sandstone and Hunter Green
1 Pound
Trim Plank
WS2591
Fax: 888-352-1790 • 845-246-3330
Weatherseal
21
Part# Description Packing/Ctn.TC138X2.6M 1-3/8" Top Cap Black 102" 12 Pcs/Ctn
TC138X3.0M 1-3/8" Top Cap Black 118" 12 Pcs/Ctn
TS15 Single Flap Top Seal 200'/Ctn
Top Seal
TS15
TS138X2.6M
TS138X3.0M
Part# DescriptionPacking/
Ctn.WS-BOTSEAL Bottom Seal fi ts 1-3/8" Wood Doors 300 ft.
WS138PVC Bottom Seal for 1-3/8" Doors1 Piece, Triple Contact
12 Pcs
WS200 PVC Bottom Seal for 2" Doors Piece, Triple Contact 8 Pcs
Bottom Seal
Bottom Seal for Wood Doors• Conforms to uneven floors.• Double contact insures
tight seal.
PVC Bottom Seal for Wood and Steel Doors• 1 pc. PVC construction. Triple contact.• Available for 1-3/8” and 2” doors.• 9 and 16 ft. lengths.
WS-BOTSEAL
WS138
Reverse Angle Jamb Seal• No tools or fasteners needed. Slips over angle.• Fits standard reverse angle track.
Reverse Angle
Part# DescriptionPacking/
CtnREVANGLE/W Reverse Angle Jamb Seal - White 200 ft
REVANGLE/B Reverse Angle Jamb Seal - Brown 200 ft
REVANGLE/BL Reverse Angle Jamb Seal - Black 200 ft
REVANGLE/G Reverse Angle Jamb Seal - Gray 200 ft
Phone: 800-431-3095 • 845-246-9525
THKAC
Perforated Angle
Powder Coated High Strength Angle• Higher strength to weight ratio over standard angle.• Minimum yield of 80,000 psi.• Gray or white powder coat baked enamel.• Requires use of HD Roper Whitney® tool to cut.
22
Angle ShearsPart# Description CapacityTRWAC-4 Roper Whitney® #4 - includes handle 2" x 2" x 1/4" Thick
TRWACBLADE-B Roper Whitney® Replacement Blade - Base
TRWACBLADE-S Roper Whitney® Replacement Blade - Shear
TRWAC-4HANDLE Roper Whitney® Replacement Handle
THKAC HK Porter® Angle Shear 1-1/4" x 1-1/4" x 1/8" Thick
HKAC-UJ HK Porter® Upper Replacement Jaw
HKAC-LJ HK Porter® Lower Replacement Jaw
TRWAC-4
Galvanized Angle• Residential & Commercial.• Bright Zinc Finish.• Cuts with either HK Porter® or
Roper Whitney® Tool.
Part# Description GaugePERF12-8 1-1/4 x 1-1/4 x 8' Galv. 12
PERF12-10 1-1/4 x 1-1/4 x 10' Galv. 12
PERF 13-8 1-1/4 x 1-1/4 x 8' Galv. 13
PERF 14-10 1-1/4 x 1-1/4 x 10' Galv. 14
PERF16-8 1-1/4 x 1-1/4 x 8' Galv. 16
PERF18-8 1-1/4 x 1-1/4 x 8' Galv. 18
PERF12X2-10 2 x 2 x 10' Galv. 12
Part# Description GaugePERF12-8.25W 1-1/4 x 1-1/4 x 8'3" White P.C. 12 Ga.
PERF12-8.25P 1-1/4 x 1-1/4 x 8'3" Grey P.C. 12 Ga.
Fax: 888-352-1790 • 845-246-3330
1-3/4" ID Torsion Springs for 7' High DoorsPrecut with cones installed
23
1-3/4" Torsion Springs
TOR1.750X _ _ _
Lbs. 1-3/4" ID ColorCycles
in 1,000's70 .192 x 20 Orange 15
80 .207 x 25 Yellow 21
90 .207 x 22-1/2 Yellow 12
100 .218 x 26 White 14
110 .225 x 27-1/2 Red 14
120 .234 x 30 Brown 15
130 .234 x 28 Brown 10
140 .243 x 31-1/2 Green 12
145 .250 X 35 Gold 16
150 .250 x 33 Gold 12
160 .262 x 39-1/2 Blue 18
165 .262 x 38 Blue 15
170 .262 x 37 Blue 13
180 .262 x 35 Blue 10
195 .273 x 39 Orange 11
230 .289 x 45 Yellow 13
• Custom sizes and uncut lengths available upon special order.
LEFT WOUNDBLACK FITTINGS
RIGHT WOUNDRED FITTINGS
• Manufactured from oil tempered springwire meeting ASTM A229.
• All Sizes available left or right wound.• Stenciled for easy identifi cation.• Coated wire for improved corrosion
resistance and easier handling.• Calculated for a minimum of 10,000
cycles at 7.6 turns.
Product Information
Options
Phone: 800-431-3095 • 845-246-9525
• Manufactured from oil tempered springwire meeting ASTM A229.
• All Sizes available left or right wound.• Stenciled for easy identifi cation.• Coated wire for improved corrosion
resistance and easier handling.• Calculated for a minimum of 10,000
cycles at 7.6 turns.
2" ID Torsion Springs for 7' High DoorsPrecut with cones installed
2" Torsion Springs
24
TOR2.00X _ _ _
Lbs. 2" ID ColorCycles
in 1,000's70 .187 x 16 Blue 11
80 .207 x 22-1/2 Yellow 22
90 .207 x 20 Yellow 12
100 .218 x 23 White 14
110 .225 x 24-1/2 Red 14
120 .234 x 27 Brown 15
130 .234 x 25 Brown 10
140 .243 x 28-1/2 Green 13
150 .250 x 30 Gold 13
160 .250 x 28 Gold 10
170 .262 x 33-1/2 Blue 14
180 .262 x 31-1/2 Blue 10
Torsion Spring Repair BlocksPart# Description Wire Size Qty/BoxTSRB-BLUE Temporary Repair Block - Blue .207 - .3065 2
TSRB-YELL Temporary Repair Block - Yellow .312 - .3625 2
TSRB-RED Temporary Repair Block - Red .375 - .4305 2TSRB-YELLOW
TSRB-BLUETSRB-RED
Product Information
• Custom sizes and uncut lengths available upon special order.
Options
Fax: 888-352-1790 • 845-246-3330
"High Cycle" Torsion Springs for 7' High DoorsPrecut with cones installed
• Springs designed for a minimum of 10,000 cycles on an 8’ high door can also be used as High Cycle springs on 7’ high doors. When these springs are used on a 7’ high door with less turns and lifting less door weight, the cycle life is greatly extended.
25
TOR1.750/ (wire x length) (R/L)
Lbs.Dimension1-3/4" ID
Cyclesin 1,000's
Color
55 .192 x 26.5 60 Orange
65 .207 x 31 60 Yellow
70 .207 x 28 37 Yellow
80 .207 x 25-1/2 23 Yellow
85 .218 x 31 30 White
95 .218 x 28 21 White
105 .225 x 29 19 Red
110 .234 x 32 20 Brown
125 .243 x 35 21 Green
130 .250 x 39 28 Gold
140 .262 x 45-1/2 36 Blue
150 .262 x 43 22 Blue
160 .262 x 40 19 Blue
165 .273 x 46-1/2 27 Orange
175 .273 x 44 21 Orange
180 .283 x 50 27 Lt. Blue
190 .283 x 48 22 Lt. Blue
200 .289 x 50-1/2 23 Yellow
High Cycle Torsion Springs
Safety Collar
Torsion spring safety warningcollar - Orange
Part# SAFETYCOLLAR
Product Information
Phone: 800-431-3095 • 845-246-9525
8' High Door Torsion Springs
1-3/4" ID Torsion Springs for 8’ High DoorsPrecut with cones installed
26
TOR1.750/ (wire x length) (R/L)8' Door
@ 8.8 turnsDimension Cycles
in 1,000'sColor
Lbs. 1-3/4" ID60 .192 x 26.5 35 Orange
75 .207 x 31 40 Yellow
80 .207 x 28 22 Yellow
90 .207 x 25-1/2 14 Yellow
100 .218 x 31 17 White
110 .218 x 28 12 White
120 .225 x 29 11 Red
130 .234 x 32 12 Brown
145 .243 x 35 12 Green
150 .250 x 39 16 Gold
160 .262 x 45-1/2 21 Blue
170 .262 x 43 16 Blue
180 .262 x 40 11 Blue
190 .273 x 46-1/2 16 Orange
200 .273 x 44 12 Orange
210 .283 x 50 16 Lt. Blue
220 .283 x 48 13 Lt. Blue
230 .289 x 50-1/2 13 Yellow
ewww.fehr.com
Fax: 888-352-1790 • 845-246-3330
Extension Springs for 7 Foot High Doors (25"-42")
Loop End Clip End
Extension Springs
27
Clip End SpringsLbs. Part# Color240 EXT2542-240 Blue
260 EXT2542-260 Brown
280 EXT2542-280 Gold
300 EXT2542-300 Tan
320 EXT2542-320 Green
330 EXT2542-330 Yellow
340 EXT2542-340 Blue
350 EXT2542-350 Red
360 EXT2542-360 Brown
Double Loop End SpringsLbs. Part # Color
40 EXT2542-040 Blue
50 EXT2542-050 Red
60 EXT2542-060 Brown
70 EXT2542-070 Orange
80 EXT2542-080 Gold
90 EXT2542-090 Light Blue
100 EXT2542-100 Tan
110 EXT2542-110 White
120 EXT2542-120 Green
130 EXT2542-130 Yellow
140 EXT2542-140 Blue
150 EXT2542-150 Red
160 EXT2542-160 Brown
170 EXT2542-170 Orange
180 EXT2542-180 Gold
200 EXT2542-200 Tan
220 EXT2542-220 Green
Lbs. Part# Color120 EXT3048-120 Green
130 EXT3048-130 Yellow
140 EXT3048-140 Blue
150 EXT3048-150 Red
160 EXT3048-160 Brown
170 EXT3048-170 Orange
Extension Springs for 8 Foot High Doors (30"-48")
• All springs rated in excess of 25,000 cycles.• Dipped black fi nish.• (25x42) fi rst number is spring length in inches,
second number equals stretch. An extensionspring will stretch 1/2 the door height.
• Spring colors conform to offi cial DASMA colors.
Double Loop End Springs
Product Information
Phone: 800-431-3095 • 845-246-9525
SHV5STUD
SHV5
Sheaves and Accessories
Spring Mounting Accessories
SHV3HD SHV4SHV4STUD
SHV4FORK
SHV3FORK
• Fully riveted sheaves.• Sheave Kits include sheaves, forks and fasteners.
Convenient 24 hour on-line ordering
Sheaves
28
Part# Description Pcs/PackE/B312X03/DP 5/16" x 3-1/2" Open Eyebolt 100
UB312X02/DP 5/16" x 2-1/4" U-Bolt 100
EGSH250X2.1/DP 1/4" x 2-1/4" S Hooks 100
Part# Description Pcs/CtnSHV3HD/DP 3" Heavy Duty Sheave 24
SHV3HDKIT 3" Heavy Duty Sheave Kit 24
SHV3FORK/DP 3" Sheave Fork 24
SHV4/DP 4" Sheave 10
SHV4KIT 4" Sheave Kit 10
SHV4FORK/DP 4" Sheave Fork 10
SHV4STUD/DP 4" Stud Sheave 10
SHV5STUD 5" Stud Sheave 5
SHV5 5" Sheave with Fork 5
E/B312X03EGSH250X2.1UB312X02
Product Information
ewww.fehr.com
Fax: 888-352-1790 • 845-246-3330
with Set Screws Cable Drums
with Set Screws Shaft Coupler
Standard Lift
Hi-Lift
* CON400-8 Standard Lift Residential Drums for use with tubular shaft only.
29
Cones and Drums
Part # Spring ID Max. Wire SizeCON175WS/SBR 1-3/4" .295
CON200WS/SBR 2" .3065
CON258WS/SBR 2-5/8" .331
WINDINGBAR 1/2" X 24" Tapered Winding Bar
WINDINGBAR18 1/2" X 18" Tapered Winding Bar
with Set Screws Spring Fittings
Part# DescriptionCON10CS Coupler for 1" Keyed Shafts
TTCOUPLER Coupler for 1" Tubular Shafts
Part# Descriptions
MaximumsDoor
HeightDoor
Wt(lbs)Cable
DiameterCON400-8 Standard Lift Residential Drum * 8'1" 530 1/8"
CON400-12 Standard Lift Light Duty Commercial 12'1" 750 1/8"
CON5250-18 Standard Lift Medium Duty Commercial 18'1" 1000 3/16"
CON400-54 Hi-Lift Light Duty 54" 120" + Hi-Lift 550 1/8"
CON5250-54 Hi-Lift Medium Duty 54" 180" + Hi-Lift 1000 3/16"
CON5750-120 Hi-Lift Medium Duty 120" 144" + Hi-Lift 1000 3/16"
TTCOUPLER
Product Information
Phone: 800-431-3095 • 845-246-9525
USA Bracket
Bearing Plates
Bearing Plates
Mini-USA Bracket
BEAR23
End Bearing Plate w/Flange
Spring Anchor PlateCenter Bearing Plate
Notched Plate End Bearing Plate
30
Part# Description Pcs/CtnENDPLTE/DP End Bearing Plate 6-5/8" Tall 24
EBFPLTE/DP End Bearing Plate w/Flange 3-3/8" Offset 24 pair
CENTRPLTE/DP Center Bearing Plate 3-3/8" Offset 24
SPRGPLTE/DP Spring Anchor Plate 3-3/8" Offset 24
NOTCHPLTE/DP Notched Spring Anchor Plate 3-3/8" Offset 24
USA-SPRGPLTE/DP Universal USA Spring Anchor Plate 8 Ga. 12 pair
RESI-SPRGPLTE/DP Mini-Resi-USA Spring Anchor Plate 12 Ga. 50
Part# Description Pcs/CtnBEAR18/DP Nylon Insert for Center Support 1x2x2-1/8 50
BEAR23/DP Heavy Duty Bearing 1x2x2-1/8 24
BEAR32/DP 1" Bearing Assy w/ 2 Holes 3-3/8" on Center 24
BEAR18 BEAR32
Bearings
Fax: 888-352-1790 • 845-246-3330 31
Part# Description
CH88Chain Hoist, Wall Mount, 4:1 ratio26' of hand chain, 36" of #41 roller chain
CH84Chain Hoist, Shaft Mount, 4:1 ratio26' of hand chain, 22" of #41 roller chain
Chain Hoists
Spring BumpersPart# DescriptionB610 Mini Spring Bumper
B620 Spring Loaded Push Down Bumper
B630 Leaf Type Spring Bumper
B620
B630
J-7
J-3
J-1
Part# Pcs/CtnJ1/DP 10
J3/DP 10
J4/DP 10
J5/DP 10
J6/DP 10
J7/DP 10
12 Gauge Jamb Brackets
CH88 CH84
Brackets & Hoists
Decorator AnglesPart# DescriptionUNIDEC Decorator Angles
UNIDEC
B610
ewww.fehr.com
Fax: 888-352-1790 • 845-246-3330
7 x 7
7 x 19
• Some sizes also available in Type 316 Stainless Steel.
• Test Certificates available upon request.• Refer to Warnings and Cautions
on page IV.• Not suitable for use on Aircraft.
33
Cable
Galvanized Aircraft Cable
Type 304 Stainless Steel Aircraft Cable
Part# Diameter TypeBreaking
Strength (lbs)2G7062 1/16" 7 x 7 480
2G7093 3/32" 7 x 7 920
2G7125 1/8" 7 x 7 1,700
2G9093 3/32" 7 x 19 1,050
2G9125 1/8" 7 x 19 2,000
2G9156 5/32" 7 x 19 2,800
2G9187 3/16" 7 x 19 4,200
2G9250 1/4" 7 x 19 7,000
Part# Diameter TypeBreaking
Strength (lbs)2S7062 1/16" 7 x 7 480
2S7093 3/32" 7 x 7 920
2S7187 3/16" 7 x 7 1,700
2S9125 1/8" 7 x 19 1,760
2S9187 3/16" 7 x 19 3,700
2S9250 1/4" 7 x 19 6,400
CORRECT INCORRECT
Available in the following reel sizes:
250', 500', 1000',5000'
Available in the following reel sizes:
250', 500', 1000',5000'
Options
Product Information
Phone: 800-431-3095 • 845-246-9525
ADJ Thimbles AN Type
Wire Rope Clips Malleable
Cable Accessories
Cable Puller
CC1
SPOOL
• Apply wire rope clips correctly. U-bolt should be on end of rope.• Re-tighten clips after initial load.• Refer to chart for minimum number of clips required for each size.
Cable Accessories
34
Part# SizeTAN093X100 3/32"-1/8"
TAN156X100 5/32"
TAN187X100 3/16"
TAN250X100 1/4"
Part# DescriptionADJX100 Cable Adjustment Clips
CC1X100 CC-1 Cable Clips
SPOOL250X100 Cable Spools 1/4"
SPOOL312X100 Cable Spools 5/16" Beveled
SPOOL437X100 Cable Spools 7/16"
Part# SizeMin.# Clips Required Pcs/Pack
WRCG125X100 1/8" 3 100
WRCG187X100 3/16" 3 100
WRCG250X100 1/4" 3 100
WRCG312X100 5/16" 3 100
Part# DescriptionCP1613-30 Cable Puller - Parallel Jaw
• Lightweight economical Grip for wire from .08" to .20".• Single "V" Groove. Jaw length is 3 inches. • Maximum Safe load is 1,500 pounds.
Safety Alert
CP1613-30
Fax: 888-352-1790 • 845-246-3330
Sleeves & Stops
• Multi-Cavity Swaging Tool. • Go/No-Go Gauge.• Metal Carrying Case.• Cable Cutting Tool.
• Aluminum Sleeves: 1/16", 3/32", 1/8", 5/32", 3/16" in 100 pc bags.
• Aluminum Button Stops: 3/32", 1/8" in 100 pc bags.
Swaging Kit
• Follow swaging instructions provided with tools.• Check fitting compression with Go/No-Go Gauge.• Adjust tool for proper compression.
35
Cable Fittings
Order online
• Sleeves, when properly applied, are capable of holding the rated breaking strength of the cable.• Stops are capable of holding one-third to one-half of the rated breaking strength of the cable.
Sleeves
Cable Size
Part Number Pcs/Pack
1/16" ASL062 100 & 1000
3/32" ASL093 100 & 1000
1/8" ASL125 100 & 1000
5/32" ASL156 100 & 1000
3/16" ASL187 100 & 1000
1/4" ASL250 100 & 1000
Stops
Cable Size
Part Number
1/16" AST062 100 & 1000
3/32" AST093 100 & 1000
1/8" AST125 100 & 1000
5/32" AST156 100 & 1000
3/16" AST187 100 & 1000
1/4" AST250 100 & 1000
Code Description1SCKIT Swage Kit - Aluminum Fittings
• Also available with copper sleeves and stops
Safety Alert
Safety Alert
ewww.fehr.comComplete Swaging Tool Kit contains:
Phone: 800-431-3095 • 845-246-9525
Felco C-9
Felco C-7/RC-8
RC-450
Angle Shear
Tools
36
• Follow swaging instructions provided with tools.• Check fitting compression with Go/No-Go Gauge• Adjust tool for proper compression..
Cable CuttersPart# Model CapacityTFC7 Felco C-7 1/64" - 3/16"
TFC9 Felco C-9 1/8" - 1/4"
TRC8 RC-8 1/64" - 3/16"
TRC450 RC-450 1/8" - 3/8"
Part# Description CapacityTRWAC-4 Roper Whitney® #4 - with Handle 2" x 2" x 1/4" Thick
TRWACBLADE-B Roper Whitney® Replacement Blade - Base
TRWACBLADE-S Roper Whitney® Replacement Blade - Shear
TRWAC-4HANDLE Roper Whitney® Replacement Handle
THKAC HK Porter® Angle Shear 1-1/4" x 1-1/4" x 1/8" Thick
HKAC-UJ HK Porter® Upper Replacement Jaw
HKAC-LJ HK Porter® Lower Replacement Jaw
TRWAC-4THKAC
Bench Model
Hand-Held Model
Swaging ToolsPart # Description CapacityTHSC600 5 Cavity Hand Swager 1/16" - 3/16"
THSC600B 5 Cavity Bench Swager 1/16" - 3/16"
1SC 5 Cavity Hand Swager 1/16" - 3/16"
1BSC 5 Cavity Bench Swager 1/16" - 3/16"
L-250 1 Cavity Hand Swager 1/4"
TGA-1P Go/No-Go Gauge for 1SC and 1BC Tools
TGA-2P Go/No-Go Gauge for L250 Tool
1SCKIT
Sturdy Metal Carrying Case complete withMulti-Cavity Hand Swager and Cable Cutting tool,
Aluminum Sleeves: 1/16", 3/32", 1/8", 5/32", 3/16"in 100 pc bags and Aluminum Stops: 3/32", 1/8"
* Also available with copper Sleeves and Stops. Part# 1SCKIT-Copper
* See note
Safety Alert
Fax: 888-352-1790 • 845-246-3330
Torsion Cable Assemblies Galvanized Aircraft Cable
Plain Loop Torsion Thimble Loop Torsion
Order online
• Torsion cables include swaged button stops.• Cable assemblies are fuse cut, machine swaged, coiled in pairs and priced per pair.• Available with: Thimble Loops, CC-1 Clips or Spool Eyes.• 25 Pair minimum order on custom made Cable Assemblies.
Cable Assemblies
37
Plain Loop Part# Size Type36601-102 3/32 x 8 ft. 6 in. 7 x 7
36601-114 3/32 x 9 ft. 6 in. 7 x 7
36602-102 1/8 x 8 ft. 6 in. 7 x 7
36602-104 1/8 x 8 ft. 8 in. 7 x 7
36602-114 1/8 x 9 ft. 6 in. 7 x 7
36612-102 1/8 x 8 ft. 6 in. 7 x 19
36612-104 1/8 x 8 ft. 8 in. 7 x 19
36612-114 1/8 x 9 ft. 6 in. 7 x 19
36612-126 1/8 x 10 ft. 6 in. 7 x 19
Truck Door Cable Assemblies 1/8” 7 x 19 Galvanized Aircraft Cable
Style Length (ins) Spool Eye (ins)Galvanized Stainless
Part# Part#
Replacement Cable for "T" style doors
110 1/4 37001-110 37601-110
115 1/4 37001-115 37601-115
130 1/4 37001-130 37601-130
97 5/16 37101-97 37701-97
125 5/16 37101-125 37701-125
Replacement Cables for "W" style doors
105 7/16 37201-105 37801-105
110 7/16 37201-110 37801-110
115 7/16 37201-115 37801-115
Spool Eye Assembly
Product Information
ewww.fehr.com
Phone: 800-431-3095 • 845-246-9525
Extension Cable Assemblies
Extension Spring Containment Cables
• Cable assemblies are fuse cut, machine swaged, coiled in pairs• Available with:Thimble Loops, CC-1 Clips or Spool Eyes.• 25 Pair minimum order on custom made Cable Assemblies.
Plain Loop Extension Thimble Loop Extension
CC-1 Clip Extension
Custom Cable Assemblies manufactured to your specifications Call us for details
• Spring Containment Cables are recommended for all extension spring installations and are required in the State of California.
• Includes Cable Adjustment Clips.
38
Cable Assemblies
Plain LoopPart# Size Type36001-144 3/32" x 12 ft. 7 x 7
36001-156 3/32" x 13 ft. 7 x 7
36001-168 3/32" x 14 ft. 7 x 7
36002-144 1/8" x 12 ft. 7 x 7
36002-156 1/8" x 13 ft. 7 x 7
36012-144 1/8" x 12 ft. 7 x 19
36012-156 1/8" x 13 ft. 7 x 19
36012-168 1/8" x 14 ft. 7 x 19
36013-144 5/32" x 12 ft. 7 x 19
36013-156 5/32" x 13 ft. 7 x 19
Part# Size Type36901-120 3/32 x 10 ft. 7 x 7
36901-156 3/32 x 13 ft. 7 x 7
36902-120 1/8 x 10 ft. 7 x 7
36902-156 1/8 x 13 ft. 7 x 7
Product Information
Product Information
Safety Alert
Cable Assemblies – Fehr Bros. manufactures lift, lock
and restraint cables in galvanized or stainless steel aircraft
cable. Cables are electrically fuse cut, machine swaged,
coiled singly or in pairs and color-coded. A variety of end
fittings are available to meet virtually any configuration.
Fastener Bags – Fastener pre-packs are an economical,
labor saving way to handle your fastener require ments.
Fasteners are poly-bagged, heat sealed and electronically
weighed to insure accuracy with thermally imprinted logo
and/or part numbers. Let Fehr Bros. streamline this segment
of your inventory needs.
Lock Bags – Take advantage of convenient
pre-packaged lock kits. Choose from one of our standard
pack ages (see page A11) or describe your own. Any
combination of handle, inside mechanism and individual
components like guides, discs, strikers and fasteners can be
poly-bagged with part numbers and/or logos for that
profes sional appearance.
Hardware Kits – Let Fehr Bros. take it one step further
and combine all of your door assembly hardware into a
custom package. Quality components, accurately packed
to your specifications.
Custom Services for Garage Door Manufacturers
& Dealers
Contact our experienced
representatives today and let
Fehr Bros. design a hardware
solution to save you time and
money.
Minimum run quantities or
production lead times may apply.
Custom Hardware Kits
39
Phone: 800-431-3095 • 845-246-9525
Fasteners
40
AccessoriesPart# Description Packing EGSH125/DP 1/8 x 1 S-Hook 100
EGSH250X2.1/DP 1/4 x 2-1/4 S-Hook 100
STRUTCLIP/DP Strut Clips 100
UB312X02/DP 5/16 x 2-1/4 U-Bolt 100
E/B312X03/DP 5/16 x 3-1/2 Open Eyebolt 100
E/S625X2/DP 5/8 x 2 Eye Screws 100
Anchor BoltsPart# Size Type Packing
C1405-100 5/16 X 1-1/2 Sleeve 100
C1433-100 3/8 X 3 Sleeve 50
C1031-100 3/8 X 2-1/8 Wedge 100
• ZP I.C.B.O. #5045• COLA RR-25039
Screws
Description Part# SizeSocket Size
Pcs/ Keg
Pcs/ Box
Type AB Sheet Metal Screws Serrated Washer Head ZP
C6360 1/4 x 3/4 7/16 10,000 1,000
Hex Washer Head Lag Screws-ZP C6045 1/4 x 1 7/16 10,000 1,000
High Profile Hex Washer Head Lag Screws ZP
C6052 5/16 x 1-5/8 7/16 4,000 1,000
C6053 5/16 x 1-3/4 7/16 4,000 1,000
C6055 5/16 x 2 7/16 4,000 1,000
C6059 5/16 x 2-1/2 7/16 3,500 500
C6061 5/16 x 3 7/16 2,500 500
Drill and Tap Screws Hex Washer Head ZP
C6322 1/4-14 x 3/4 7/16 2,500 1,000
C6326 1/4-14 x 1 7/16 2,500 1,000
C6327 1/4-20 x 3/4 7/16 2,500 1,000
C6329 1/4-20 x 1 7/16 2,500 1,000
C6332 5/16-12 x 1 7/16 5,000 1,000
• Standard Carton quantity is 1000 pcs. unless otherwise noted. • Standard Zinc Plated Fasteners are not suitable for use with pressure treated lumber.
TYPE AB SHEET METAL SCREWS
HEX WASHER HEAD LAG SCREWS
DRILL AND TAP SCREWS
HIGH PROFILE HEX WASHER HEAD LAG SCREWS
C1405
EGSH250x2.1E/B312x03
STRUTCLIP
E/S625X2
UB312X02
Product Information
Fax: 888-352-1790 • 845-246-3330
Description Part# SizeSocket Size Pcs/Keg Pcs/Box
Flat Head Carriage Bolts Full Thread ZP
C6072 1/4-20 x 1-3/4 - 6,000 1,000
C6073 1/4-20 x 1-7/8 - 6,000 1,000
C6076 1/4-20 x 2-1/4 - 6,000 1,000
C6078 1/4-20 x 2-1/2 - 6,000 1,000
Round Head Carriage Bolts Full Thread ZP
C6095 5/16-18 x 3/4 - 8,000 1,000
Slotted Track Bolts Knurled Shank ZP
C6142 1/4-20 x 5/8 - 12,500 1,000
C6146 1/4-20 x 1 - 10,000 1,000
Hex Head Bolts Full Thread ZP
C6102 1/4-20 x 3/4 7/16 15,000 1,000
C6104 1/4-20 x 1 7/16 12,000 1,000
C6112 5/16-18 x 3/4 1/2 8,000 1,000
C6114 5/16-18 x 1 1/2 7,000 1,000
C6122 3/8-16 x 3/4 9/16 6,000 1,000
C6128 3/8-16 x 1-1/2 9/16 3,000 500
Nuts
41
Fasteners
Description Part# SizeSocket Size Pcs/Keg Pcs/Box
Hex Nuts - ZP
C6160 1/4-20 7/16 20,000 1,000
C6163 5/16-18 1/2 14,000 1,000
C6165 3/8-16 9/16 8,500 1,000
Hex KepLock Nuts - ZP
C6201 1/4-20 7/16 20,000 1,000
C6203 5/16-18 1/2 8,000 1,000
Serrated Flange Nuts - ZP
C6211 1/4-20 7/16 20,000 1,000
C6215 5/16-18 1/2 12,000 1,000
C6216 3/8-16 9/16 8,500 1,000
USS Flat WashersDescription Part# Size Pcs/Ctn
Flat Washer - ZPC6213 5/16 1000
C6214 3/8 1000
ROUND HEAD CARRIAGE BOLT
SLOTTED TRACK BOLT
HEX HEAD BOLT
Bolts
• Standard Carton quantity is 1000 pcs. unless otherwise noted. • Standard Zinc Plated Fasteners are not suitable for use with pressure treated lumber.
FLAT HEAD CARRIAGE BOLT
Phone: 800-431-3095 • 845-246-9525
Lubricants
Lubriplate® Products
Fehr Lubricants
• America’s most popular Door & Operator lubricants.• Protects against rust and corrosion.• Multi-Lube sprays on like a foam and
sets up in minutes to a tough, protective grease.• Use on track, rollers, cables, pulleys, hinges and
other moving parts.
• Special Low Temperature Grease is ideal in cold climates. Lubricates to -60° F.
• LP Aero recommended for screw drive and chain drive operators.
Slipit® Sliding Compound
• #1 Choice for Rolling Steel Doors.• Non-toxic FDA and USDA approved.• SLIPIT® Sliding Compound With Silicones
is available in aerosol spray or gel compound.
42
Part# Description Pcs/CaseLP-LT Low Temperature Grease, 10 oz. 12
LP-AERO Lithium Based Grease, 1-3/4 oz. 24
Part# DescriptionCans/Case
L6970 Fehr Multi-Purpose Lube, 16 oz. 12
L6950 Fehr Multi-Methylene free, 13.5 oz. 12
L6930 Fehr Penetrating Oil, 15 oz. 12
Part# Description Pcs/CaseSLIPIT-SPRAY 11 oz. Aerosol Spray 12
SLIPIT-P 1 Pint Gel 24
SLIPIT-Q 1 Quart Gel 12
SLIPIT-G 1 Gallon Gel 4
SLIPIT-5G 5 Gallon Gel 1
Scrubs®
• Packed 6 pails per case.• Ideal for cleaning dirt and lubricants from doors,
tools and hands.
Part# Description
SCRUBS Scrubs® Waterless Cleaner Towels
Product Information
Product Information
Fax: 888-352-1790 • 845-246-3330
Replacement Hardware for “T Style” Roll-Up Doors
• Black CED plating for superior corrosion resistance.• Tight tolerances eliminate excess door noise.
Truck Door Hardware
43
Part# Description Pcs/CtnT69035 End Hinge 50
T61196 Center Hinge 100
T69433 Top Bracket, Assembled 50
T61352 Bottom Fixture 50
T61401 Heavy Duty Lift Handle 50
T61204 Cable Anchor Bracket 100
BEAR32/DP1" Bearing Assembly w/ 2 Holes 3-3/8" on Center
24
BEAR32
T61196
T61204
T61352T69035
T61401T69433
Product Information
Phone: 800-431-3095 • 845-246-952544
Truck Door Accessories
Part# Description Replaces Pcs/CtnROLL4026/DP 1" Machined Roller 61244 50
ROLL22/DP 1" Stamped Roller 12 50
ROLL23/DP 2" Nylon Roller 3228 50
ROLL24/DP 2" Steel Roller 2996 50
ROLL24
Truck Door Rollers
Truck Door Cable Assemblies 1/8” 7 x 19 Aircraft Cable
Style Length (ins) Spool Eye (ins)Galvanized Stainless
Part# Part#
Replacment Cablefor "T" style doors
110 1/4 37001-110 37601-110
115 1/4 37001-115 37601-115
130 1/4 37001-130 37601-130
97 5/16 37101-97 37701-97
125 5/16 37101-125 37701-125
Replacement Cablesfor "W" style doors
105 7/16 37201-105 37801-105
110 7/16 37201-110 37801-110
115 7/16 37201-115 37801-115
ROLL23
ROLL4026
ROLL22
Phone: 800-431-3095 • 845-246-952546
Residential Models
Part# Model# Max. CableDrum Diam. Control
ZAP815RL-B Residential Model B 4" Single button
ZAP815RL-C Residential Model C 6.5" Single Button
• Works on doors up to 160 square feet• Maximum door weight - 500 pounds• Minimum door height - 6.5 feet • Includes cover kit
Jackshaft Operators
Commercial Models
Part# Model # Driven Pulley ControlMax. Cable Drum Diam.
ZAP805-B Super Drive Model B 4" Pulley Drive Three Button 6"
ZAP805-C Super Drive Model C 5" Pulley Drive Three Button 8.75"
ZAP805-D Super Drive Model D 6" Pulley Drive Three Button 10"
ZAP8042 Cover Kit
Chain Release Models
Cable Release Models
Part# Model # Driven Pulley ControlMax. CableDrum Diam.
ZAP815-B Super Drive Model B 4" Pulley Drive Three Button 6"
ZAP815-C Super Drive Model C 5" Pulley Drive Three Button 8.75"
ZAP815-D Super Drive Model D 6" Pulley Drive Three Button 10"
ZAP815RG-B Mini Commercial Model B 4" Pulley Drive Single Button 6"
ZAP8042 Cover Kit
Residential
Chain release ZAP Cover
Product Information
• Works on doors up to 170 square feet• Maximum door weight - 775 pounds• Minimum door height - 6.5 feet Maximum door height - 25 feet• UL 325 approved (commercial models)
Product Information
Fax: 888-352-1790 • 845-246-3330 47
Jackshaft Operators
Heavy Duty Commercial Models
Part# Model# Driven Pulley ControlMax. Cable Drum Diam.
ZAP8815-B HD Super Drive Model B 4" Pulley Drive Three Button 6"
ZAP8815-D HD Super Drive Model D 6" Pulley Drive Three Button 13"
ZAP8052 Cover Kit
Cable Release Model
Part# Model# Driven Pulley ControlMax. Cable Drum Diam.
ZAP8816-B HD Super Drive Model B 4" Pulley Drive Three Button 6"
ZAP8816-D HD Super Drive Model D 6" Pulley Drive Three Button 13"
ZAP8157 Cover Kit
Chain Hoist Model
• Works on doors up to 350 square feet • Maximum door weight - 1600 pounds • Minimum door height - 9.5 feet • Maximum door height - 40 feet • UL 325 approved (commercial models)
Battery Back Up
Battery Backup for Series 800 & 880 Units
Part# ZAP8830
The Choice of Professionals
ZAP8816
ZAP8815
Autolock
Auto Lock System with Cover, Cable & Module
Part# ZAP8070
Product Information
Phone: 800-431-3095 • 845-246-952548
Jackshaft Operator Accessories
Motor Cable & Plug
Motor Cable and Plug19.5 feet
Part# ZAP0078
Retro Refl ective Photo Cell
Retro Refl ective Photo cellPolarized - 26' range
Part# ZAP401000
Plug In Internal Antennae
Plug in Internal Antennae
Part#ZAPRC2416
Wall Mount Antennae
Wall Mount AntennaeAdjustable
Part# ZAPRC2414
Super Grip Transmitter
Super Grip Transmitter2 Channel
Part# ZAPRC4202
Plug In Radio Receiver
Plug in Radio RecieverNo Antennae
Part# ZAPRC840
MK2 Receiver Accessory
MK2 Receiver AccessoryInterface Module
Part# ZAPRC871
Adaptor Module
Adaptor Module forModels 871 & 8070
Part# ZAPRC872
ewww.fehr.com
The Parts You NeedFehr Bros. stocks a wide
range of hardware to meet most installation
and replacement needs.
Excellent serviceis our commitment to you from our headquarters inSaugerties, NY and ourservice warehouse in San Francisco.
Save SSOur pricing puts you
ahead of the competition. You will also save the freight
on orders of $250 or more
* FREE FREIGHT on all orders over $250
Extension SpringsTorsion Springs
CableCable Assemblies
Cable FittingsDrums &ConesTop Brackets
Bottom BracketsTools
Zap Operators
WeathersealPerforated Angle
LubricantsFastenersSheaves
Bearing Plates Spring Bumpers
Reverse Angle SealBottom Seal
Quick Close Fixtures
Rollers Hinges
Operator ReinforcementBrackets
Locks & LatchesLift Handles
Extension Cords Key Switch &
Disconnect Devices Truck Door Parts
www.garagedoorsupplies.com