Upload
lekhanh
View
266
Download
1
Embed Size (px)
Citation preview
Hydraulic self-cleaning screen filters, that require no external power sourceFiltomat M100 Filters
flow rates minimum operating pressure
water for cleaning filtration degrees
M100: up to 1,760 gpm(400 m3/h)
MG: up-to 3,522 gpm (800 m3/h)
36 psi (2.5 bar) less than 1% of the total flow 500-80 micron
• Reliable operating mechanism
• Simple construction and easy maintenance
• Ideal solution for agricultural filtration requirements
• Automatic flushing according to pressure differential
• No interruption of downstream flow during flushing
• High reliability and durability
features:
How the Filtomat Filters Work
GeneralThe Amiad Filtomat M100 Series are mid-range automatic filters, ideal for remote installation sites, with a water-driven self-cleaning mechanism that doesn’t require external power source to operate. With their various screen areas the M100 models support flow rates of up to 3522 gpm (800 m³/h), with filtration degrees of 500 down to 80 micron and inlet/outlet diameters from 2”-14”.
The Filtering ProcessThe filtration process begins when raw water flows through the filter inlet (1) into the new coarse screen (2). Here, the water is pre-filtered in order to protect the cleaning mechanism from large debris. The water then passes through the inner surface of the fine screen; dirt particles are trapped and accumulate inside the filter while clean water flows through the filter outlet. The gradual dirt buildup on the inner screen surface causes a filter cake to develop, with a corresponding increase in the pressure differential across the screen.
The Self-Cleaning Process When the pressure differential across the screen reaches a pre-set level of 7 psi (0.5 bar), the M100 filter starts the cleaning process by opening the internal flush valve. This results in the release of a back-flush stream flowing through the nozzles (3) out of the hollow suction scanner shaft (4) and the turbine (5) to the drainage pipe (6).
MG ModelsModular configuration, available as a stand alone or as filter bank assembly, with a single control system (AC/DC).The MG modules are delivered fully assembled, requiring a single connection to the inlet, outlet and drain.
Amiad’s Filtomat MG Series consists of the following models:MG110 (2 x 108LP) for up-to 1,761 gpm (400 m3/h)MG112 (3 x 108LP) for up-to 2,642 gpm (600 m3/h)MG114 (4 x 108LP) for up-to 3,522 gpm (800 m3/h)
M100 ModelsAmiad’s Filtomat M100 Series consists of the following models:M100-750 for up to 176 gpm (40 m³/h)M100-1500 for up to 352 gpm (80 m³/h)M100-4500 for up to 793 gpm (180 m³/h)M100-6800 for up to 1,760 gpm (400 m³/h)
(1)
(3)
(2) (4)
(6)(5)
Filter Type M100-750 M100-1500 M100-4500 M100-6800
General Data
Maximum flow rate*175 gpm(40 m³/h)
350 gpm(80 m³/h)
793 gpm(180 m³/h)
1760 gpm(400 m³/h)
Inlet/Outlet diameter2” 50 mm3” 80 mm
3” 80 mm4” 100 mm
4” 100 mm6” 150 mm
4” 100 mm6” 150 mm8” 200 mm10” 250 mm
Standard filtration degrees 500, 300, 200, 130, 100, 80 micron
Min. working pressure36 psi (2.5 bar)
For lower pressure please consult Amiad
Max. working pressure 116 psi (8 bar) 150 psi (10 bar)
Max. working temperature 131°F (55°C)
Weight [empty]2” 48.5 lb (22 kg)3” 55 lb (25 kg)
3” 66 lb (30 kg)4” 77 lb (35 kg)
4” 198 lb (90 kg)6” 253.5 lb (115 kg)
4” 242.5 lb (110 kg)6” 264.5 lb (120 kg)8” 308.6 lb (140 kg)10” 348 lb (158 kg)
* Consult Amiad for optimum flow depending on filtration degree & water quality.
Flushing Data
Minimum flow for flushing66 gpm
(15 m³/h)88 gpm
(20 m³/h)114 gpm(26 m³/h)
132 gpm(30 m³/h)
Reject water volume per flush cycle (at 2 bar - 39 psi)
4 gallon(15 liter)
5.2 gallon(20 liter)
33 gallon(125 liter)
40 gallon(150 liter)
Flushing cycle time 10 seconds 15 seconds
Exhaust valve1.5”
40 mm
Flushing criteria Differential pressure of 0.5 bar (7 psi), time intervals and manual operation
Screen Data
Filter area116 in²
(750 cm²)232 in²
(1500 cm²)698 in²
(4500 cm²)1054 in²
(6800 cm²)
Screen types Molded weave wire stainless steel 316L
*Construction Materials
Filter housing Epoxy-coated carbon steel 37-2 (stainless steel 316L on request)
Filter lid Epoxy-coated carbon steel 37-2 (stainless steel 316L on request) high density polypropylene
Cleaning mechanism PVC and stainless steel 316L
Exhaust valve Brass, stainless steel 316L, BUNA-N
Seals BUNA-N
Control Brass, stainless steel 316L, and acetal
* Amiad offers a variety of construction materials. Consult us for specifications.
Technical Specifications - M100 Models
M100 - 750 (M102C, M103C)
M100 - 1500 (M103CL, M104C)
M100 - 4500 (M104LP, M106LP, M104LPN)
M100 - 6800 (M104XLP, M106XLP, M108LP, M110LP)
M100 Models:
14.0
2.0
PSI
4.0
3.0
5.0
7.0
0.5
0.7
0.3
0.2
0.4
1.4
6 10 20 40 60 200 100
0.2
0.04
0.060.08
0.02
0.1
2 4
BAR
0.80.6
1.0
0.4
20 10 6 50
4000 1000 400 2000
200 100 500 1000
GPMM³/H 1
3” M100-1500
4” M100-1500
14.0
2.0
PSI
4.0
3.0
5.0
7.0
0.5
0.7
0.3
0.2
0.4
1.4
6 10 20 40 60 200 100
0.2
0.04
0.060.08
0.02
0.1
2 4
BAR
0.80.6
1.0
0.4
20 10 6 50
4000 1000 400 2000
200 100 500 1000
GPMM³/H 1
2” M100-750
3” M100-750
50
200 20 10 6 60 40 100
4
0.23.0
0.1
0.02
0.080.06
0.04
1.4
0.4
0.2
0.3
0.7
0.5
2.0
2
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
6 10 20
400 2000 1000
500 100 200 1000 1
GPMM³/H
4” M100-4500
6” M100-4500
Ø 13" (330)
21”
(531
) *27
” (68
4)28
” (71
0) *
38” (
965)
Ø 13" (330)
50
200 20 GPM 10 6 60 40 100
4
0.23.0
0.1
0.02
0.080.06
0.04
M³/H
1.4
0.4
0.2
0.3
0.7
0.5
2.0
2
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
6 10 20
400 2000 1000
500 100 200 1000 1
4” M100-6800
6” M100-6800
8” M100-6800
10” M100-6800
Head Loss Graphs (in clean water)
*Approx. length required for maintenanceDim: inch (mm)
Typical Dimensional Drawing
(900) (467)
82.2” (2088) *5.9” (150)
8.8”(22.3)
*40.4” (1025)
INLET OUTLET
DRAIN35.4" 18.4”
105.63” (2683)
15.08”(900) (969) (383)
35.43” 38.15”
INLET OUTLET
DRAIN
MG112
MG114
Filter Type MG110 MG112 MG114
General Data
Maximum flow rate* 1,761 gpm (400 m³/h) 2,642 gpm (600 m³/h) 3,522 gpm (800 m³/h)
Inlet/Outlet diameter 10” (250 mm) 12” (300 mm) 14” (350 mm)
Standard filtration degrees 500, 300, 200, 130, 100, 80 micron
Min. working pressure 36 psi (2.5 bar) for lower pressure please consult Amiad
Max. working pressure 150 psi (10 bar)
Max. working temperature 140°F (60°C)
Weight [empty] 117 lb (325 kg) 1,054 lb (480 kg) 1,590 lb (723 kg)
Flushing Data
Minimum flow for flushing (at 30 psi - 2 bar) 130 gpm (30 m³/h) 195 gpm (45 m³/h) 260 gpm (60 m³/h)
Reject water volume per flush cycle (at 39 psi - 2 bar) 70 gallon (250 liter) 105 gallon (375 liter) 140 gallon (500 liter)
Flushing cycle time 45 sec. depends on working pressure
Exhaust valve 1 1/5” (40 mm)
Flushing criteria Differential pressure of 7 psi bar (0.5), time intervals and manual operation
Technical Specifications - MG Models
* Consult Amiad for optimum flow depending on filtration degree & water quality.
MG110
MG Models:
* Amiad offers a variety of construction materials. Consult us for specifications.
Typical Dimensional Drawing
105.7” (2685)
(383)15.08”
(1100)43.3”
(769)30.26”
INLET OUTLET
DRAIN
105.7” (2685)
(383)15.08”
(1100)43.3”
(769)30.26”
INLET OUTLET
DRAIN
105.7” (2685)
(383)15.08”
(1100)43.3”
(769)30.26”
INLET OUTLET
DRAIN
Head Loss Graphs (in clean water)
0.11.4
0.08
0.06
0.04
0.7
0.5
0.23.0
4.0
2.0
200
1000 600
100 1000
4000
500
2000
BARPSI
GPMM³/H
14” MG114
0.11.4
0.08
0.06
0.04
0.7
0.5
0.23.0
4.0
2.0
200
1000 600
100 1000
4000
500
2000
BARPSI
GPMM³/H
12” MG112
0.11.4
0.08
0.06
0.04
0.7
0.5
0.23.0
4.0
2.0
200
1000 600
100 1000
4000
500
2000
BARPSI
GPMM³/H
10” MG110
Filter Type MG110 MG112 MG114
Screen Data
Filter area 2,108 in² (13,600 cm²) 3,162 in² (20,400 cm²) 4,216 in² (27,200 cm²)
Screen types Stainless steel 316L, molded plastic support structure
* Construction Materials
Filter housing Epoxy-coated carbon steel 37-2. (stainless steel 316L on request)
Filter lid Epoxy-coated carbon steel 37-2 (stainless steel 316L on request) high density polypropylene
Cleaning mechanism PVC and stainless steel 316L
Exhaust valve Brass, Stainless Steel 316, BUNA-N
Seals BUNA-N
Control Aluminum, brass, stainless steel 316, PVC, acetal
Amiad Water Systems Ltd. D.N. Galil Elyon 1, 1233500, Israel,Tel: +972 4 690 9500, Fax: +972 4 814 1159,E-mail: [email protected]
Headquarters
910101-000477/06.2016
W A T E R S Y S T E M S
www.amiad.comCopyright © 2013 Amiad Water Systems Ltd. All rights reserved. The contents of this catalogue including without limitation all information and materials, images, illustrations, designs, icons, photographs, graphical presentations, designs, literary works, data, drawings, slogans, phrases, names, trademarks, tittles and any other such materials that appear in this catalogue (collectively, the “Contents”) are the sole and property of Amiad Water Systems Ltd. (“Amiad”). Amiad has sole and exclusive right, title and interest in the Contents, including any intellectual property rights, whether registered or not, and all know-how contained or embodied therein. You may not reproduce, publish, transmit, distribute, display, modify, create derivative works from, sell or participate in any sale of, or exploit in any way, in whole or in part, any of the Contents or the catalogue. Any use of the catalogue or the Contents, other than for personal use, requires the advanced written permission of Amiad.
The Americas Amiad USA Inc. Main Office and Manufacturing: 120-J Talbert Road, Mooresville, NC 28117,Tel: +1 704 662 3133, Fax: +1 704 662 3155, Toll Free: 1 800 24 FILTER, E-mail: [email protected] www.amiadusa.com
West Coast Sales Office and Warehouse:1251 Maulhardt Ave, Oxnard, CA 93030Tel: +805 988 3323, Fax: +805 988 3313, Toll Free: +1 800 969 4055
BrazilAmiad Sistemas de Água Ltda., Av. Funchal, 411, Conj. 42, Vila Olimpia, São Paulo, CEP 04551-060Tel: +55 11 31923824, E-mail: [email protected] Oil & Gas, E-mail: [email protected]
MexicoAmiad Mexico SA DE CV, Vialidad de la Barranca # 6 Piso 4,Col. Valle de las Palmas 52787. Huixquilucan (Interlomas), Edo de Mexicoo,Tel/Fax: +52 55 636 28122, E-mail: [email protected]
IndiaAmiad Filtration India Pvt Limited, 305 Sai Commercial Building, Govandi St Rd, Govandi Mumbai 400 088, Tel: +91 22-67997813/14, Fax: +91 22-67997814, Email: [email protected] China (Yixing Taixing Environtec Co., Ltd.) 70 Baihe Chang, Xingjie Yixing Jiangsu, 214204,Tel: +86 510 87134000, Fax: +86 510 87134999, E-mail: [email protected] AsiaFiltration & Control Systems Pte. Ltd., 22 Sin Ming Lane #07-71 Midview City, Singapore 573969, Tel: +65 6 337 6698, Fax: +65 6 337 8180, E-mail: [email protected]
Asia
Amiad Australia Pty Ltd. 138 Northcorp Boulevard, Broadmeadows, Victoria 3047,Tel: +61 3 93585800, Fax: +61 3 93585888, E-mail: [email protected]
Australia
Amiad Water Systems Europe SAS, Ilot No4 ZI La Boitardière, 37530 Chargé, France,Tel: +33 (0) 2 47 23 01 10, Fax: +33 (0) 2 47 23 80 67, E-mail: [email protected] Water Systems Europe SAS (Irrigation Division) 100 avenue de l’Anguillon, Z.I. des Iscles, 13160 Chateaurenard, Tel: +33 (0) 4 32 60 10 01, Fax +33 (0) 4 32 60 60 85
GermanyAmiad Water Systems SAS Europe (German branch office) Zweigniederlassung Deutschland Prinz-Regent-Str. 68 a 44795 Bochum,Tel: +49 (0) 234 588082-0, Fax: +49 (0) 234 588082-10, E-mail: [email protected]
United KingdomAmiad Water Systems UK Limited, Compass Business Centre, Unit 6, Lion Way, Swansea Enterprise Park, Swansea SA7 9FBTel: +44 (0)1792 277290, Fax: +44 (0)1792 797707, E-mail: [email protected]
Europe