Upload
ada-paloma-soto-brambila
View
1.722
Download
77
Tags:
Embed Size (px)
Citation preview
C 16060 -- 1 en 0906 / ANKO 1 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
2 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
C 16060 -- 1 en 0906 / ANKO 3 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
1.1. Fault codes of engine control (PLD--MR) via SAE J1939
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
45/12 16409D) heater flange open circuit-fault (heaterflange defec-tive)
The heating flange becomes af-ter Kl. 15 uniquely brieflyswitched on. Here if no break--down of the battery voltage isrecognized, the heating flange isclassified as defective. Errorthreshold and cyclic duration aredeposited in the data record
94/0 11715 fuel pressuresensor or fuelpressure &temperaturesensor
measuringrange exceed-ed or short cir-cuit to terminal30 / terminal 15
If a fuel pressure sensor or acombination sensor fuel pres-sure & temperature is fitted tothe engine depends on the en-gine make
94/1 11716 combination in-put (FPS, P--DK)
remains undermeasuringrange or shortcircuit toground
94/2 11717 combination in-put (FPS, P--DK)
signal not plau-sible
94/3 13015 combination in-put (FPS, P--DK)
open circuit
94/4 13016 combination in-put (FPS, P--DK)
short circuit toground
94/14 11917 Fuel line signalnot plausible *
measured val-ue not plausi-ble
98/2 02026 engine oil cir-culation*
fluid level toohigh / too low
-- message via CAN:warning oil level too high (=98/0)or advance warning (=98/1) orwarning oil level too low (=98/1)
4 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
02517 oil level sensor(up to diagno-sis version 4)
measured val-ue not plausi-ble
-- check oil level, correct if nec-essary.
-- check wire for short circuit tobattery, repair or replace ifnecessary.
-- check oil level sensor, replaceif necessary. nominal value:20--25 Ohm
-- perform functional check.
98/4 02515 oil level sensor**
measuringrange exceed-ed
-- check oil level, correct if nec-essary.
-- check wire for short circuit toground, repair or replace ifnecessary.
-- check oil level sensor, replaceif necessary. nominal value:20--25 Ohm
-- perform functional check.
98/3 02516 oil level sensor**
measured val-ue not plausi-ble
-- check oil level, correct if ne-cessary.
-- check wire for short circuit toground, repair or replace ifnecessary.
-- check oil level sensor, replaceif necessary. nominal value:20--25 Ohm
-- perform functional check.
98/5 02509 oil level sensor**
open circuitfault
-- check oil level sensor , re-place if necessary.
-- check wire for open circuitfault, repair or replace if nec-essary.
-- perform functional check
C 16060 -- 1 en 0906 / ANKO 5 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
100/2 11617 oil pressuresensor
signal not plau-sible
-- check oil level, correct if ne-cessary.
-- check wire for open circuitfault, repair or replace if nec-essary.
-- check oil pressure sensor, re-place if necessary.
-- perform functional check.
100/3 11615 oil pressuresensor
measuringrange exceed-ed
-- check oil pressure sensor, re-place if necessary.
-- check wire for open circuitfault or if shortened to battery-voltage, repair if necessary.
-- perform functional check.
100/4 11616 oil pressuresensor
remains undermeasuringrange
-- check oil pressure sensor, re-place if necessary.
-- check wire for short circuit toground, repair if necessary.
-- perform functional check.
100/14 02020 engine oil cir-culation **
pressure toolow
-- message via CAN: oil pres-sure advance warning orwarning
102/0 11820 booster path * boost pressuretoo high
-- if fault codes 11415 or11417are also present, processthem first.
-- boost pressure system (boostair tubes, boost air cooler)visual check.
-- perform functional check.
102/1 11818 booster path* booster pathdefective
-- check tubes and connectionsbetween turbocharger, boostair cooler and theboost air tubes for leakage.
-- check boost air cooler.-- perform functional check.
6 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
102/2 11417 boost pressuresensor
measured val-ue not plausi-ble
-- check wire for open circuitfault, repair if necessary.
-- check boost pressure sensor,replace if necessary.
-- perform functional check.-- if fault code 01315 or 01316
also actual: replace and cali-brate ECU engine control(e.g. MR--PLD).
102/3 11415 boost pressuresensor
measuringrange exceed-ed
-- check boost pressure, re-place if necessary.
-- check wire for open circuitfault and if shorted to batteryvoltage, repair if necessary.
-- perform functional check.
102/4 11416 boost pressuresensor
remains undermeasuringrange
-- unplug the connector fromcombination sensor. faultcodes 01215 and 11415 actu-al: replace combination sen-sor.
-- check wire for short circuit toground, repair if necessary.
-- perform functional check.
102/13 11873 booster path /boost pressurecontrol **
max. output ofbooster speedbalancing gov-ernor
102/13 11874order01874
booster path /boost pressurecontrol
set value devi-ation too high
(with power reduction)-- check booster path fault
codes 11874* , 01874**
102/13 11875 booster path /boost pressurecontrol*
boost pressuredeviation toohigh
102/13 11876 booster path /boost pressurecontrol *
braking powertoo low
C 16060 -- 1 en 0906 / ANKO 7 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
102/13 12415 scavenginggradient sensor(P2S--P3)**
(boost pres-sure ) measur-ing range ex-ceeded
-- check sensor, replace if nec-essary.
-- check wire for open circuit
102/13 12416 scavenginggradient sensor(P2S--P3)**
(boost pres-sure ) remainsunder measur-ing range
-- check sensor, replace if nec-essary.
-- check wire for open circuit
103/7 12612 no speedbooster 1**
no enginespeed
103/14 12712 no speedbooster 2**
no enginespeed
105/0 01822 booster path ** temperature tohigh
-- temperature of boost pres-sure too high
105/3 11215 boost tempera-ture sensor
measuringrange exceed-ed
-- check temperature sensor,replace if necessary.
-- nominal value: 2.4 k Ohm(corresponds to 21°C)
-- check wire if connected to bat-tery voltage and if open circuitfault, repair if necessary.
-- perform functional check.
105/4 11216 boost tempera-ture sensor
remains undermeasuringrange
-- check temperature sensor,replace if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C)
-- check wire for short circuit toground, repair if necessary.
-- perform functional check.
110/0 02122 coolant tem-perature sen-sor *
temperaturetoo high
8 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
110/3 11515 coolant tem-perature sen-sor
measuringrange exceed-ed
-- check sensor, repair or re-place if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C)
-- check wire for open circuitfault or if shortened to batteryvoltage, repair if necessary.
-- perform functional check.
110/4 11516 coolant tem-perature sen-sor
remains undermeasuringrange
-- check sensor, repair or re-place if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C)
-- check wire for open circuitfault, repair or replace if nec-essary.
-- perform functional check.
158/2 12219 terminal 15detection *
inconsistencyMR<-->FR ter-minal 15
-- check fuse, replace if neces-sary.
-- check wires and plug connec-tors for open circuit fault, re-pair or replace if necessary.
-- perform functional check.
158/2 12319 terminal 50detection*
inconsistencyMR<-->FR ter-minal 50
-- check wires and plug connec-tors for open circuit fault, re-pair if necessary.
-- check wires and plug connec-tors for open circuit fault, re-pair if necessary.
168/3 07542 terminal 30,battery voltage
nominal rangeexceeded
-- 24 V--Mode: 30 V, 12 V--Mode: 16 V
-- alternator or governer defect
C 16060 -- 1 en 0906 / ANKO 9 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
168/4 07543 terminal 30,battery voltage
remains belownominal range
-- 24 V--Mode: 22 V, 12 V--Mode: 10 V
-- battery defect-- alternator, governor or fuse
defect
174/3 11115 fuel tempera-ture sensor
measuringrange exceed-ed
-- check wire, repair or replace ifnecessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C).
-- check wire if shortened to bat-tery voltage and if open circuitfault, repair if necessary.
-- perform functional check
174/4 11116 fuel tempera-ture sensor
remains undermeasuringrange
-- check sensor, repair or re-place if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C).
-- check wire for short circuit toground, repair if necessary.
-- perform functional check
175/3 01015 oil temperaturesensor
measuringrange exceed-ed
-- check oil temperature sensorand replace if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C).
-- check wire for ground short,repair if necessary.
-- perform functional check.
175/4 01016 oil temperaturesensor
remains undermeasuringrange
-- check oil temperature sensorB11 and replace if necessary.
-- nominal value: 2.4 kOhm(corresponds to 21°C).
-- check wire for ground short,repair if necessary.
-- perform functional check
10 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
190/0 10530 engine speed engine speedtoo high
-- inform about authorized en-gine speed
-- delete fault memory
609/11 04056 internal fault* backup controldefective*
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- if fault code is still present, re-new and program control unit.
-- perform functional check.
609/12 01315 ambient pres-sure sensor
measuringrange exceed-ed
-- if fault codes 11415 or 11416are present, remove themfirst.
-- fault code 01315 remainspresent: read out actual val-ues 014 and 015 andcompare with each other.
-- actual value should be insidetolerance band (+/-- 10%)while engine stops.
609/12 01316 ambient pres-sure sensor
remains undermeasuringrange
-- if fault codes 11415 or 11416are present, remove themfirst.
-- fault code 01316 remainspresent: read out actual val-ues 014 and 015 andcompare with each other.
-- actual value inside toleranceband (+/-- 10%) while enginestops: replace andprogram ECU engine control(e.g. MR--PLD).
C 16060 -- 1 en 0906 / ANKO 11 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
609/12 04024 internal fault auxiliary con-troller defective
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- if fault code is still present, re-new and program control unit.
-- perform functional check.
609/12 14034D) internal fault** HS--transistorPVB1 high--re-sistance High-side--Transistor
-- Change control unit
609/12 14035D) internal fault** HS--transistorPVB2 high--re-sistance
-- Change control unit**
609/12 14036D) internal fault HS--transistorPV5 high--re-sistance
-- Change control unit**
609/12 04038 internal fault* high resistancestarter driver(redundant--/auxiliary path)
present, remove this faultcode first.
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- perform functional check.
609/12 14038 internal fault** starter driverhigh--resist-ance (mainpath)
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- perform functional check.
12 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
609/12 14039 internal fault* 14039 starterdriver low--re-sistance (mainpath or auxilia-ry path)
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- perform functional check
609/12 04040 internal fault level detectionstarter defec--tive
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- perform functional.
609/12 14041 internal fault(till diagnosisversion 4)
PV-- Highside--transistor de-fective
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- perform functional check.
609/12 14054 internal fault CAN--data areadefective
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- if fault code is still present, re-place and program controlunit.
-- --perform functional check.
C 16060 -- 1 en 0906 / ANKO 13 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
609/12 18039 internal fault** Starter outputstage with lowimpedance(main branchor branch ofemergency) orload(relay) also tohigh resistanceand/or to highinductance.
Main branch:During the controller initializa-tion the two transistors of themain branch arealternating switched on briefly.The level at the starter outputchanges thereby on”High”, the main branch isclassified as low impedance.
Backup branch:If that changes for clamp 50signal on ”High” and followsthis level change achange of the level at the start-er output before the starteroutput stage wasactivated, the backup branchis classified as low imped-ance.
609/14 04037 internal fault cylinder num-ber implausible
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- --perform functional check.
609/14 04047 internal fault characteristicdata map de--fective
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- --perform functional check.
14 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
609/14 04048 internal fault cylinder num-ber implausible
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- --perform functional check.
609/14 14049 internal fault ** parametrizationfault
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- --perform functional check.
609/14 04050 internal fault incorrect hard-ware detection
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- --perform functional check.
609/14 04051 internal fault EEPROM:Checksum fail-ure1 (memoryfault)
-- check all affected connectors,plug connections and electri-cal components for damage,loose contact, corrosion etc.and repair if necessary.
-- if fault code is still present, re-new and program control unit.
-- --perform functional check.
609/14 14052 internal fault EEPROM:CKS-- fault 2(groups vehicleparameters)
-- check all affected plugs, plugconnectors and electricalcomponents for damage,loose contact, corrosion etc.and repair if necessary.
-- if fault code is still present, re-place and program controlunit.
-- --perform functional check.
C 16060 -- 1 en 0906 / ANKO 15 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
609/14 24053 internal fault ** EEPROM:Checksum--fault 3 (blockproduction orimmobilizer).
-- check all affected connectors,plug connections and electriccomponents for damage,loose contact, corrosion etc.,and repair if necessary.
-- if fault code still present, re-new and calibrate control unit.
-- --perform functional check .
611/4 06506 oil separator* short circuit toground diag-nostic line.
611/12 06564 oil separator* oil separatordefective
625/2 10102 CAN connec-tion
CAN data notplausible
-- work off actual faults of SGFRE apart from CAN data busfault codes 10201, 00202 and10203.
-- perform functional check.
625/2 10104 CAN connec-tion
no connectionto CAN
-- check CAN connection to SGFRE.
-- check cables, connectors,plug connectors and electricalcomponents for damage, cor-rect connection, loose contactand corrosion, repair if neces-sary.
-- remove engine CAN bus faultin the SG FRE.
-- perform functional check-- communication with the ECU
engine control (e.g. MR--PLD)restored: check calibration ofECU engine control (e.g. MR--PLD) for one wire capability.
16 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
625/14 10100 CAN connec-tion
CAN--High de-fective
-- check for open circuit fault, re-pair or replace if necessary.
-- switch on ignition.-- delete fault memory in ECU
engine control (e.g. MR--PLD).-- delete fault memory in SG
FRE.-- --perform functional check .
625/14 10101 CAN connec-tion
CAN--Low de-fective
-- check wire for open circuitfault, repair of replace if neces-sary.
-- switch on ignition.-- delete fault memory in ECU
engine control (e.g. MR--PLD).-- delete fault memory in SG
FRE.-- perform functional.
625/14 10149 CAN connec-tion
parameter faultCAN
-- check parameters and-- perform functional check
636/1 10310 crankshaftposition sensor
crankshaft lev-el too low
-- pull out position sensor whileengine is stopped and performvisual check.
-- remove metal pieces/shav-ings if necessary.
-- replace position sensor in thecase of mechanical damage(clear stress marks).
-- replace clamping sleeve of theposition sensor if necessary.
-- press--in speed (position) sen-sor during engine standstill un-til mechanical limit stop.
-- --perform functional check
C 16060 -- 1 en 0906 / ANKO 17 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
636/3 10309 crankshaftposition
crankshaft sen-sor open circuitfault
-- check wire and position sen-sor for open circuit fault, re-place if necessary.
-- --nominal value 1.2 kOhm.
636/4 10308 crankshaftposition
crankshaft sen-sor ground
-- check wire and position sen-sor for ground short, replace ifnecessary.
-- --nominal value 1.2 kOhm.
636/7 10311 crankshaftposition sensor
crankshaft/camshaft sig-nal assignmentnot plausible
-- pull out position sensor duringengine standstill and performvisual check.
-- replace position sensor in thecase of mechanical damage(clear stress marks).
-- check crankshaft-- and cam-shaft position sensor for tightfitting, replace clampingsleeve if necessary.
-- check wires at plug connec-tion for damage, correct con-nection andcorrosion, repair if necessary.
-- --check crankshaft-- and cam-shaft position sensor at plugfor interchanging.
636/8 10312 crankshaftposition
crankshafttimeout -- no-crankshaft sig-nal Timeout
-- press in speed (position) sen-sor during engine standstilluntil mechanical limit stop.
-- fault code 10309 actual: workoff this fault code.
-- fault code 10312 actual:check crankshaft positionsensor, replace if necessary.
-- --nominal value 1.2 kOhm
18 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
636/14 10313 crankshaftposition
crankshaft sen-sor wrong po-larity
-- connect the position sensorcorrectly.
-- --perform functional check.
651/3 24805 control sole-noid valve**
shortened tobattery voltage-Highside bank1
-- shortened to battery voltage-Highside bank 1
651/3 24905 control sole-noid valve**
shortened tobattery voltage-Highside bank2
-- switch off solenoid valvesbank 2
651/3 24905 control sole-noid valve**
shortened tobattery voltage-Highside bank2
-- switch off solenoid valvesbank 2
651/4 24806 control sole-noid valve**
ground shortLow side bank1
-- switch off solenoid valvesbank 1
651/4 24906 control sole-noid valve**
ground shortLowside bank2
-- switch off solenoid valvesbank 2
651/5 15027 control failureinjector--/sole-noid valve
control cylinder1 disturbed
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine--smooth-ness control has to be set tozero.
651/6 25028 solenoid valvecylinder 1**
short circuit in-jector solenoidvalve cylinder 1
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
C 16060 -- 1 en 0906 / ANKO 19 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
651/7 15026 contact recog-nition injector--/solenoid valve
no contact cyl-inder 1
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
651/12 09044 engine--smoothnesscylinder 1
LRR--limitationcylinder 1
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
651/14 09045 individual cylin-der adaption
EZA--limitationcylinder 1
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero
652/5 15127 injector--/sole-noid valve cyl-inder 2
control cylinder2 disturbed /failure
-- upon removing mechanical orelectrical faults at the injectorvalves, the engine--smooth-ness control has to be set tozero.
-- the engine--smoothness con-trol can be set to zero in themenu ”controls” at the menulevel ”check engine--smooth-ness control”.
652/6 25128 solenoid valvecylinder 2**
short circuit in-jector--/
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
20 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
652/7 15126 contact recog-nition injector--/solenoid valvecylinder 2
no contact cyl-inder 2
-- upon removing mechanical orelectrical faults at the injectorvalves, the engine--smooth-ness control has to be set tozero.
-- the engine--smoothness con-trol can be set to zero in themenu ”controls” at the menulevel ”check engine--smooth-ness control”.
652/12 09144 injector--/sole-noid valve cyl-inder 2
engine--smoothnesscontrol: LRR--limitation cylin-der
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
652/14 09145 injector--/sole-noid valve cyl-inder
individual cylin-der adaptation:EZA--limitationcylinder
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero
653/5 15227 injector--/sole-noid valve cyl-inder 3
control cylinder3 disturbed /failure
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine--smooth-ness control has to be set tozero.
653/6 25228 injector--/sole-noid valve cyl-inder 3**
short circuit in-jector--/ sole-noid valve cyl-inder 3
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
C 16060 -- 1 en 0906 / ANKO 21 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
653/7 15226 injector--/sole-noid valve cyl-inder 3
contact recog-nitioninjector--/sole-noid valve: nocontact cylin-der 3
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
653/12 09244 injector--/sole-noid valve: cyl-inder 3
engine--smoothnesscontrol: LRR--limitation cylin-der
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
653/14 09245 injector--/sole-noid valve: cyl-inder 3
individual cylin-der adaptation:EZA--limitationcylinder 3
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
654/5 15327 control failureinjector--/sole-noid valve
contact recog-nition injector--/solenoid valve:no contact cyl-inder 4
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
654/6 25328 injector--/sole-noid valve cyl-inder 4**
short circuit in-jector--/ sole-noid valve cyl-inder 4
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
654/7 15326 injector--/sole-noid valve cyl-inder 4
contact recog-nition injector--/solenoid valve:no contact cyl-inder 4
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
22 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
654/12 09344 injector--/sole-noid valve cyl-inder 4
engine--smoothnesscontrol: LRR--limitation cylin-der 4
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
654/14 09345 injector--/sole-noid valve cyl-inder 4
individual cylin-der adaption:EZA--limitationcylinder 4
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
655/5 15427 injector--/sole-noid valve cyl-inder 5
contact recog-nition injector--/solenoid valve:no contact cyl-inder 5
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
655/6 25428 injector--/sole-noid valve cyl-inder 5 **
short circuit in-jector--/ sole-noid valve cyl-inder 5
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
655/7 15426 injector--/sole-noid valve cyl-inder 5
contact recog-nition injector--/solenoid valve:no contact cyl-inder 5
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
655/12 09444 injector--/sole-noid valve cyl-inder 5
engine--smoothnesscontrol: LRR--limitation cylin-der 5
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
C 16060 -- 1 en 0906 / ANKO 23 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
655/14 09445 injector--/sole-noid valve cyl-inder 5
individual cylin-der adaptation:EZA--limitationcylinder 5
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
656/5 15527 injector--/sole-noid valve cyl-inder 6
control failureinjector--/sole-noid valve:control cylinder6 disturbed
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
656/6 25528 injector--/sole-noid valve cyl-inder 6**
short circuit in-jector--/ sole-noid valve cyl-inder 6
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
656/7 15526 injector--/sole-noid valve cyl-inder 6
contact recog-nition injector--/solenoid valve:no contact cyl-inder 6
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
656/12 09544 injector--/sole-noid valve cyl-inder 6
engine--smoothnesscontrol: LRR--limitation cylin-der 6
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
656/14 09545 injector--/sole-noid valve cyl-inder 6
individual cylin-der adaption:EZA--limitationcylinder 6
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
24 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
657/5 15627 injector--/sole-noid valve cyl-inder 7
control failureinjector--/sole-noid valve
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
657/6 25628 injector--/sole-noid valve cyl-inder 7**
short circuit in-jector--/ sole-noid valve cyl-inder 7
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
657/7 15626 injector--/sole-noid valve cyl-inder 7
contact recog-nition injector--/solenoid valve:no contact cyl-inder 7
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
657/12 09644 injector--/sole-noid valve cyl-inder 7
engine--smoothnesscontrol: LRR--limitation cylin-der 7
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
657/14 09645 injector--/sole-noid valve cyl-inder 7
individual cylin-der adaptation:EZA--limitationcylinder 7
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
658/5 15727 injector--/sole-noid valve cyl-inder 8
control failureinjector--/sole-noid valve:control cylinder8 disturbed
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
C 16060 -- 1 en 0906 / ANKO 25 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
658/6 25728 injector--/sole-noid valve cyl-inder 8**
short circuit in-jector--/ sole-noid valve cyl-inder 8
-- check electrical screw con-nections of the affected injec-tor valve for short circuit.
-- disconnect electrical screwconnections of the affected in-jector valve.
658/7 15726 injector--/sole-noid valve cyl-inder 8
contact recog-nition injector--/solenoid valve:no contact cyl-inder 8
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
658/12 09744 injector--/sole-noid valve cyl-inder 8
engine--smoothnesscontrol: LRR--limitation cylin-der 8
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
658/14 09745 injector--/sole-noid valve cyl-inder 8
individual cylin-der adaptation:EZA--limitationcylinder 8
important note:-- upon removing mechanical or
electrical faults at the injectorvalves, the engine smooth-ness control has to be set tozero.
677/3 18005 starter control(PLD--MR)**
starter relayexternal cur-rent supply
-- check wire -- terminal 50 inputof starter relay if shortened tobattery voltage, repair or re-place if necessary.
-- check starter relay, replace ifnecessary.
-- restore electrical connec-tion(s)
26 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
677/5 18009 starter control(PLD--MR)**
starter relayexternal cur-rent supply
-- check of starter relay if short-ened to battery voltage, repairor replace if necessary.
-- check starter relay, replace ifnecessary.
-- restore electrical connec-tion(s)
677/6 18008 starter control(PLD--MR)**
short circuit toground
-- check wire -- terminal 50 inputof the starter relay for shortcircuit to ground, repair or re-place if necessary.
-- check starter relay, replace ifnecessary.
677/7 18086 starter control(PLD--MR)**
starter doesnot engage
-- check starter electrically andmechanically.
-- perform functional check.
677/14 18033 starter controlStarter relay is(PLD--MR)**
starter relayfixed in closedposition
-- check starter relay, replace ifnecessary.
-- perform functional
697/3 17007D) proportionalvalve (MBR--BK)
shortened tobattery voltage(--lead)
-- set output off
17705 proportionalvalve bank1PVB
shortened tobattery voltage(+lead)*
-- set output off 1 2 3 4
697/4 17708 proportionalvalve bank 1(PVB 1)
short circuit toground(+lead)**
-- set output off 1 2 3 4
C 16060 -- 1 en 0906 / ANKO 27 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
697/5 17009 proportionalvalve 1 (MBR--BK)
open circuitfault** ECU en-gine control(e.g. MR--PLD)wrong calibra-tion.
-- check parametrization.-- parameter 06 has to be set to
NOT ACTIVE-- if not, then the data set of ECU
engine control (e.g. MR--PLD)is wrong
-- replace and program ECU en-gine control (e.g. MR--PLD).
-- --perform functional check.
697/6 17006 proportionalvalve 1 (MBR--BK)
short circuit toground (--lead)ECU enginecontrol (e.g.MR--PLD)wrong calibra-tion.
-- check parametrization.-- parameter 06 has to be set to
NOT ACTIVE-- if not, then the data set of ECU
engine control (e.g. MR--PLD)is wrong
-- replace and program ECU en-gine control (e.g. MR--PLD).
-- perform functional check.
698/3 17305C)17307D)
proportionalvalve 2 (MBR--KD)
shortened tobattery voltage(--lead) HighSide
-- set output off
698/5 17317C)17309D)
proportionalvalve 2 (MBR--KD)
open circuitfault Low Side
-- set output off
698/6 17306 proportionalvalve 2 Activa-tion: enginebrake reecom-pression valve(MBR--KD)
short circuit toground (--lead)High Sidewrong calibra-tion
-- check calibration, correct ifnecessary. Parameter 007has to be set to NOT ACTIVE.
-- if not, then the data set of thecontrol unit MR is wrong.
-- replace and program ECU en-gine control (e.g. MR--PLD).
-- perform functional check.
28 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
699/3 17107D) proportionalvalve 3
shortened tobattery voltage(--lead)*
-- set output off
699/5 17109 proportionalvalve 3
open circuitfault wrong cal-ibration
-- check calibration, correct ifnecessary. Parameter 008has to be set to NOT ACTIVE.
note:-- if a Linig--fan is installed, the
following calibration applies:
a) parameters 8 and 9 have tobe set to ACTIVE.
b) parameter 14 has to be setto ”Type 0”.
699/6 17106 proportionalvalve 3
short circuit toground (--lead)ECU enginecontrol (e.g.MR--PLD)wrong calibra-tion / short cir-cuit to ground
-- check calibration, correct ifnecessary. Parameter 008has to be set to NOT ACTIVE.
-- if the calibration is OK, checkwire for short circuit to ground,repair or replace if necessary.
-- if still no fault can be detected,replace and program ECU en-gine control (e.g. MR--PLD).
-- perform functional check.
700/3 17207** proportionalvalve 4
shortened tobattery voltage(--lead)*
-- set output off
C 16060 -- 1 en 0906 / ANKO 29 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
700/5 17209 proportionalvalve 4
open circuitfault
note: ECU engine control (e.g.MR--PLD) wrong calibration /open circuit fault
-- check calibration, correct ifnecessary. Parameter 009has to be set to NOT ACTIVE.
note:-- if a Linnig--fan is installed, the
following calibration applies:
a) parameters 8 and 9 have tobe set to ACTIVE.
b) parameter 14 has to be setto ”Type 0”.
-- fault code17209 remains ac-tual: check wires for open cir-cuit fault, repair or replace ifnecessary.
-- if no fault can be detected, re-place and program ECU en-gine control (e.g. MR--PLD)
-- --perform functional check.-- set output off
30 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
700/6 17206 proportionalvalve 4
short circuit toground (--lead)
note: ECU engine control (e.g.MR--PLD) wrong calibration /short circuit to ground
-- check calibration, correct ifnecessary. Parameter 009has to be set to NOT ACTIVE.
-- check calibration, correct ifnecessary. Parameter 009has to be set to NOT ACTIVE.if the calibration is OK, checkwire for short circuit to ground,repair or replace if necessary.
-- if still no fault can be detected,replace and program ECU en-gine control (e.g. MR--PLD).
-- perform functional check.
705/3 17405 proportionalvalve 5
shortened tobattery voltage(+lead)*
-- set output off
705/4 17408 proportionalvalve 5
short circuit toground (+lead)*
-- set output off for valve 6 and 5.
705/11 17805 proportionalvalve bank 2PVB 2
shortened tobattery voltage(+lead)*
-- set output off for valve 6 and 5.
705/11 17808 proportionalvalve bank 2PVB 2
short circuit toground (+lead)*
-- set output off for valve 6 and 5.
706/3 17609 proportionalvalve 6
open circuitfault *
-- set output off for valve 6
723/3 10409 camshaft posi-tion
camshaft sen-sor open circuitfault
-- check wire for open circuit, re-place if necessary.
-- nominal value: 1.2 kOhm
C 16060 -- 1 en 0906 / ANKO 31 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
Fault--codes.SAEJ1939SPN/FMI****
Fault--codes.PLD--MR***
Description Repair instructions
723/4 10408 camshaft posi-tion sensor
camshaft sen-sor groundshort
-- check wire and position sen-sor for ground short, replace ifnecessary.
-- nominal value: 1.2 kOhm nec-essary.
723/8 10412 camshaft posi-tion sensor
camshaft time--out (no camshaft signal)Timeout
-- if fault codes 10408 and10409 are current, removethem first
-- pull out position sensor duringengine standstill and performvisual check
-- remove metal pieces/shav-ings if necessary.
-- replace position sensor in thecase of mechanical damage(clear stress marks).
-- press in speed (position) sen-sor during engine standstilluntil mechanical limit stop.
-- perform functional check.
723/14 10413 camshaft posi-tion
camshaft sen-sor wrong po-larity Sensorverpolt
-- position sensor correctly withpin of the ECU engine control(e.g. MR--PLD)
-- perform functional check
986/8 17112 fan speed no signal (time-out) Timeout
currently not fan speed detec-tion installed.
-- check calibration, correct ifnecessary. Parameter 14 hasto be set to ”Type 0”.
* diagnosis version 5 D)=only for the D--Model of PLD--MR control units (diagnosisversion 6)
**diagnosis version 6 and newer
*** Minidiag 2 Diagnostic unit
**** Driving panel master gauge (P1)
32 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
1.2. Fault codes of vechile control (ADM2) via SAE J1939
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--line)
***
Description Remedial action Pin
45/3 10003 decom--pressionvalveMBR_KD
open circuit -- check wiring-- check solenoid valve
15/10
45/4 10004 decom--pressionvalveMBR_KD
shorted toground
-- check wiring-- check solenoid valve
15/10
84/3 10103 vehiclespeedsignal C3
open circuit -- check wiring-- check parameter 08/01
15/03
84/4 10104 vehiclespeedsignal C3
shorted toground
-- check wiring 15/03
84/14 10114 vehiclespeedsignal C3
value notplausible
-- check parameter 08/01 15/03
91/0 10200 analogacceleratorpedal
acceleratorpedal not ad-justed
-- restart accelerator pedaladjustment routine
-- check wiring-- Limit value idle operation
position: 5,0 V-- Limit value kick down
position: 4,9 V
21/11
91/2 10202 analogacceleratorpedal
voltage notplausible
-- Pedal unit exchange, ifdefective
-- check wiring-- Limit value idle operation
position: 5,0 V-- Limit value kickdown
position: 4,9 V
C 16060 -- 1 en 0906 / ANKO 33 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--
line)***
Description Remedial action Pin
91/3 10203 analogacceleratorpedal
voltage toohigh orshorted tobattery volt-age
-- Pedal unit exchange, if de-fective
-- check wiring-- Limit value idle operation
position: 5,0 V-- Limit value kickdown posi-
tion: 4,9 V
21/11
91/4 10204 analogacceleratorpedal AFPS
voltage toolow orshorted toground
-- Pedal unit exchange, if de-fective
-- check wiring-- Limit value idle operation
position: 5,0 V-- Limit value kickdown posi-
tion: 4,9 V
21/11
98/0 10400 oil level oil level tohigh
-- Oil discharge with tostrong overstocking.
-- remark: This problem canoccur also if in PLD--MRthe false type of oil panwere programmed.
PLD--MR
98/1 10401 oil level low oil level -- refill oil PLD--MR
98/14 10414 oil level oil level toolow
-- refill oil-- remark: This problem can
occur also if in PLD--MRthe false type of oil panwere programmed.
PLD--MR
100/1 10501 oil pressuresensor
low oil pres-sure
-- check oil pump and oil cir-cuit
PLD--MR
100/14 10514 oil pressuresensor
oil pressuretoo low
-- check oil pump and oil cir-cuit.
PLD--MR
107/0 10800 air filtersensor
air pressuretoo high
-- check wiring. 15/08
107/3 10803 air filtersensor
open circuit -- check wiring. 15/08
34 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--
line)***
Description Remedial action Pin
107/4 10804 air filtersensor
shorted toground
-- check wiring. 15/08
110/0 10900 coolanttemperature
high coolanttemperature
-- cooling--water level andcooling circuit check.
PLD--MR
110/14 10914 coolanttemperature
coolanttemperaturetoo high
-- cooling--water level andcooling circuit check.
PLD--MR
111/1 11001 coolantlevel
low coolantlevel
-- refill coolant-- check wiring
15/07
111/3 11003 coolantlevel
open circuit -- check wiring-- Voltage must be larger
than 2,0 V.
15/07
111/4 11004 coolantlevel
shorted toground
-- check wiring. 15/07
158/0 11100 terminal 15(ignition)
over voltage -- check battery voltage-- check parameter 2/08
(24V/12V selection)
21/02
158/1 11101 terminal 15(ignition)
under voltage -- check battery voltage-- check parameter 2/08
(24V/12V selection)
21/02
558/1 11701 idle switch(analog ped-al)
Wiring idlevalidationswitch GAS1and GAS2twisted oropen circuit atpotentiometerground FP--
-- check wiring-- Pedal unit exchange, if de-
fective
21/12and21/13or21/14
558/5 11705 idle switch(analog ped-al)
both switchesopen circuit(GAS2 +GAS1 open)
-- check wiring-- Pedal unit exchange, if de-
fective
21/12and21/13
558/12 11712 idle switch(analog ped-al)
both switchesclosed(GAS2 +GAS1 closed)
-- check wiring-- Pedal unit exchange, if de-
fective
21/12and21/13
C 16060 -- 1 en 0906 / ANKO 35 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--
line)***
Description Remedial action Pin
599/12 11812 cruise controlswitchCC+ and CC--
both switchesclosed
-- check wiring-- check cruise control switch
18/04and18/05
601/12 11912 cruise controlswitchCC+ and CC--
both switchesclosed
-- check wiring-- check cruise control switch
18/04and18/05
620/3 12103 power supplyanalog pedal(AFP+)
voltage toohigh
-- supply voltage > 5,2 V. 21/09
620/4 12104 power supplyanalog pedal(AFP+)
voltage toolow
-- supply voltage < 4,8 V. 21/09
625/2 12202 CAN linkADM2 -- MR
no commu-nication withMR
-- check wiring (engine CAN)-- check configuration:
MR parameter (../..) andADM2 parameter 1/01
to be set to equal function-ality(0ne wire capability)
625/14 12214 CAN linkADM2 -- MR
one wiremode
-- check wiring (engine CAN)-- check configuration:
MR parameter (../..) andADM2 parameter 1/01
to be set to equal function-ality (One wire capability)
629/12 12312 ADM2 internal error
677/5 13305 output relay 1 open circuit -- check wiring-- check relay 1
15/12
677/6 13306 output relay 1 shorted toground
-- check wiring-- check relay 1
15/12
730/0 13900 output relay 2 grid heater:no increasingboost temper-ature after ac-tivation
-- check wiring-- check relay 2-- check grid heater
15/09
36 (37)
MERCEDES BENZENGINE FAULT CODES
C 16060 -- 1 en 0906 / ANKO
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--
line)***
Description Remedial action Pin
730/1 13901 output relay 2 grid heater:relay perma-nently closed
-- check wiring-- check relay 2
15/09
730/2 13902 output relay 2 grid heater:relay perma-nently closed
-- check wiring-- check relay 2
15/09
730/3 13903 output relay 2 voltage toohigh orshorted tobattery volt-age
-- check wiring 15/09
730/4 13904 output relay 2 voltage toolow or shortedto ground
-- check wiring-- check relay 2
15/09
974/2 14202 remote pedalHFG
supply volt-age out ofrange
-- limit values for the supplyvoltage of the HFG:
Minimum value: 4,8 V andmaximum value: 5,2 V.
18/17
974/3 14203 remote pedalHFG
voltage toohigh orshorted tobattery volt-age
-- check wiring-- check remote pedal
18/18
974/4 14204 remote pedalHFG
voltage toolow or shortedto ground
-- check wiring-- check remote pedal
18/18
1004/3 14403 output relay 4 open circuit -- check wiring-- check relay 4
18/01
1004/4 14404 output relay 4 shorted toground
-- check wiring-- check relay 4
18/01
1005/3 14503 output PWMpedalsupplyor transmissi-on
open circuit -- check wiring. 15/05
1005/4 14504 output PWMpedalsupplyor transmissi-on
shortedto ground
-- check wiring. 15/05
C 16060 -- 1 en 0906 / ANKO 37 (37)
MERCEDES BENZENGINE FAULT CODES
E 2006 SANDVIK TAMROCK CORP., Tampere PlantP.O. Box 100FI--33311 TAMPERE, FinlandTel.: +358 205 44 121FAX: +358 205 44 120
ADM2fault
codes(J1939)
SPN/FMI****
ADM2fault
codes(k--
line)***
Description Remedial action Pin
1006/3 14603 exhaust brakevalveMBR_BK
open circuit -- check wiring-- check exhaust brake valve
15/06
1006/4 14604 exhaust brakevalveMBR_BK
shorted toground
-- check wiring-- check exhaust brake valve
15/06
639/2 14902 J1939 CAN--interface
CAN identifi-ers ETC#1 orACC#1 miss-ing
-- PGN ETC1 was receivedonly once and did not dis-appear.
1015/1 15001 PWM acceler-ator pedal
no supplyvoltage
-- check wiring 15/05
1015/2 15002 PWM acceler-ator pedal
both signalsmissing(GAS1 andGAS2)
-- check wiring-- Pins 21/13, 21/12, 15/05 ,
21/14.
1015/3 15003 PWM acceler-ator pedal
signal GAS2,not available
-- check wiring-- Pins 21/13, 15/05 , 21/14.
1015/4 15004 PWM acceler-ator pedal
signal GAS1,not available
-- check wiring-- Pins 21/12, 15/05 , 21/14.
1015/5 15005 PWM acceler-ator pedal
acceleratorpedal not ad-justed
-- restart accelerator pedaladjustment routine
1015/6 15006 PWM acceler-ator pedal
idle positionout of ad-justed range
-- restart accelerator pedaladjustment routine
1015/7 15007 PWM acceler-ator pedal
acceleratorpedal out ofadjustedrange
-- restart accelerator pedaladjustment routine
* diagnosis version 5 D)=only for the D--Model of PLD--MR control units (diagnosisversion 6)
** diagnosis version 6 and newer
*** Minidiag 2 Diagnostic unit
**** Driving panel master gauge (P1)