FANUC Spares - University of Colorado Boulderucc.colorado.edu/fanuc/drivrlst.pdf · Page 7 of 49 CIMPLICITY HMI I/O Communications February 2001 GE Fanuc Automation North America,

GE Fanuc Automation North America, Inc.

GE Fanuc Automation

CIMPLICITY Monitoring and Control Products

CIMPLICITY HMI Plant Edition I/O Communications Guide

February 2001

FANUC Spares

https://industrialautomation.co/product-category/fanuc/page/5934/


CIMPLICITY and Genius are registered trademarks and Series 90, Series Six, Series Five, and Logicmaster are trademarks of GE Fanuc Automation North America, Inc. Windows, Windows NT, and Windows 95 are registered trademarks of Microsoft Corporation PLC, PLC-2, and PLC-3 are registered trademarks and AdvancedDDE, Data Highway and RSLinx are trademarks of Allen-Bradley Company, Inc. Modbus, Modbus PLUS, SA84 and SM85 are trademarks of Groupe Schneider. STEP and SINEC are registered trademarks of Siemens AG. APPLICOM is a trademark of Applicom International. Mitsubishi is a registered trademark of Mitsubishi Electronics, Inc. OMRON is a registered trademark of OMRON Electronics, Inc. Seriplex is a trademark of Square D Corporation Other products and company names mentioned in this document are trademarks and registered trademarks of their respective companies.

Copyright 1998,1999 GE Fanuc Automation North America, Inc. All Rights Reserved

Page 3 of 49 CIMPLICITY HMI I/O Communications February 2001


Table of Contents

The CIMPLICITY I/O Communications Products List ................................................................................4 Third Party OPC/DDE Servers and CIMPLICITY Drivers ........................................................................15 Allen-Bradley Communications..................................................................................................................22 Allen-Bradley Data Highway Plus Communications..................................................................................23 Allen-Bradley DF-1 Communications ........................................................................................................24 Allen-Bradley Intelligent Antenna Communications..................................................................................25 CCM2 Communications..............................................................................................................................27 DDE Client Communications......................................................................................................................28 Descartes Systems OmniServer™ ..............................................................................................................29 FloPro FloNet Communications .................................................................................................................30 Genius®Communications ............................................................................................................................31 Honeywell IPC 620 Communications.........................................................................................................32 Johnson Controls N2 Communications.......................................................................................................33 CIMPLICITY® Marquee Interface..............................................................................................................34 Mitsubishi A Series Serial Communications ..............................................................................................35 Mitsubishi TCP/IP Communications ..........................................................................................................36 Modbus RTU Communications ..................................................................................................................37 Modbus Plus Communications ...................................................................................................................38 Modbus TCP/IP Communications ..............................................................................................................39 OMRON Host Link Communications.........................................................................................................40 Omron TCP/IP Communications ................................................................................................................41 OPC Client Communications ......................................................................................................................42 Series 90™ Communications......................................................................................................................43 Series 90™ TCP/IP Communications.........................................................................................................44 Sharp TCP/IP Communications ..................................................................................................................45 Siemens TI Serial Communications............................................................................................................46 Smarteye Communications .........................................................................................................................47 Square D SY/MAX Communications .........................................................................................................48 Toyopuc Ethernet Communications............................................................................................................49

FANUC Spares




The CIMPLICITY I/O Communications Products List The CIMPLICITY I/O Communications Product List that follows is the current listing of CIMPLICITY drivers and Third Party communications products for use with CIMPLICITY HMI. The list includes CIMPLICITY products that are available as of Release 5.0.

The third party OPC and DDE I/O Servers and third party CIMPLICITY drivers are provided as a reference only based on current information at the time of publication. You must contact the listed software provider for pricing, sales, support, and detailed technical information.

The Communications Product column contains one of the following:

• = A CIMPLICITY part number for a CIMPLICITY Driver that can be ordered from GE Fanuc. In this case the CIMPLICITY Product name and part numbers are listed.

• = A Third Party Reference which may be: ♦ = A third party CIMPLICITY I/O Driver ♦ = An OPC Server ♦ = An AdvancedDDE Server ♦ = A DDE Server All third party references will include an index number in parenthesis that identifies the vendor for this driver. See the listing of Third Party OPC/DDE Servers and CIMPLICITY Drivers in the next section for the vendor name and contact information.

• = Call for availability – contact your sales channel for a quote.



Manufacturer Device Protocol NT Communications Product ABB MOD30,

MODCELL XMODBUS YES OPC Client (20)

Advant IMS CIM APT YES OPC Client (41) Advant, Kent DCS,

MOD300, P4000 Ethernet Yes OPC Client (41)

Advant YES OPC Client (34) Advant

Masterpiece Serial Ethernet

YES DDE Client (13)

Procontic CS31 Arcnet YES OPC Client (11) SPA BUS YES OPC Client (11) ACS600, DCS600,

ACS1000 Drives DDCS Network YES OPC Client (33)

Freelance YES OPC Client (35) DPU, IMPRS,

MDAR, MMCO Serial to Tasnet NIM

YES TASNET NIM Interface (19)

Addi-Data Digital/Analog PC Boards

Digital/Analog PC Boards

N/A AdvancedDDE Client Communications (2)

Allen-Bradley SLC-5/04

PLC-5 Data Highway Plus (KTX)

YES Allen-Bradley Communications Part No.: IC646NEA000

SLC-5/04, SLC-5/05, PLC-5, 3, 2 PLC/5-250

Ethernet YES Allen Bradley Communications Part No.: IC646NEA000

SLC-5/04 PLC-5, 3, 2 PLC-5/250

Data Highway Plus (KT)

YES Allen-Bradley Data Highway Plus Part No.: IC646NDH000

SLC-5/0x PLC-5

RS-232 YES Allen-Bradley DF-1 Communications Part No.: IC646NDF000

2750-AS RS-232 YES Allen-Bradley Intelligent Antenna Communications Part No.: IC646NRF000

SLC-5/0x RS-232 via Dial-out and Radio Modems

YES AdvancedDDE Client (3)

PLC-5C ControlNet YES AdvancedDDE Client (14) OPC Client (14) OPC Client (25)

PLC-5, PLC/5-250 Ethernet N/A AdvancedDDE Client (14) OPC Client (14)

PLC-5, SLC-5/04 DH+ YES OPC Client (25) Logix 5550 Ethernet YES AdvancedDDE Client (14)

OPC Client (14) Analog Devices 6B Series Serial YES AdvancedDDE Client (10)

OPC Client (10)

FANUC Spares




Manufacturer Device Protocol NT Communications Product April PLC JBUS YES OPC Client (26) 1000 Series Ethernet YES OPC Client (26) Aromat FP Series Aromat Computer

Link YES AdvancedDDE Client (10)

OPC Client (10) ASI Controllers Serial YES DDE Client (13) Aspen Technology CIM/21 TCP/IP YES OPC Client (41) BACnet ARCNET,

Ethernet YES OPC Client (21)

Bailey Net 90/ Infi-90 RS-232 YES AdvancedDDE Client Communications (15)

Net 90/Infi 90 RS-232 YES OPC Client (17) Net 90/Infi 90 RS-232 YES OPC Client (41) INIC1103 semAPI OPC Client (41) Freelance 2000 YES OPC Client (35) Baker CAC 8510 RTU Serial YES DDE Client (3) Barber Colman MACO 8000 RS-232 YES DDE Client (13) MACO 4000

MACO 5000 MACO 6000 Advantage EZ

RS-485 YES

Baslar BEI-DFPR Tasnet NIM YES TASNET NIM Interface (19) Beckhoff TwinCAT YES OPC Client (45) Beckwith M-2001 Tasnet NIM YES TASNET NIM Interface (19) Bentley Nevada BTG YES OPC Client (46) Bitronics MTWIE1 Tasnet NIM YES TASNET NIM Interface (19) Bristol Babcock RTU BSAP YES OPC Client (3) BSAP, OPEN BSI YES OPC Client (22) OPEN

ENTERPRISE YES OPC Client (22)

CANOpen CANOpen YES OPC Client (23) OPC Client (24) OPC Client (44)

Cegelec GEM 80 EIA-485 YES OPC Client (47) Conitel 2020, 3000, 2100H,

C-300 Tasnet NIM YES TASNET NIM Interface (19)

Contrex CX1000 Binary Link YES AdvancedDDE Client (10)

OPC Client (10)



Manufacturer Device Protocol NT Communications Product Control Data Corp TypeI, TypeII Tasnet NIM YES TASNET NIM Interface (19) Cooper CL4C, CL-5A Tasnet NIM YES TASNET NIM Interface (19) Cuttler Hammer D/50 , D/300 Serial YES AdvancedDDE Client (10)

OPC Client (10) Daniels Flow Meters Serial YES AdvancedDDE Client

Communications (3) Datap Simulation

Leakwarn YES OPC Client (41)

DeviceNet Open DeviceNet YES OPC Client (25) YES OPC Client (24) YES OPC Client (23) YES OPC Client (44) YES AdvancedDDE Client (14) DNP 3.0 RTU DNP 3.0 YES Call for availability Elsag Bailey Net 90/ Infi-90 RS-232 YES AdvancedDDE Client

Communications (15) Net 90/Infi 90 RS-232 YES OPC Client Communications

(17) Freelance 2000 YES OPC Client (35) Endres Hauser Memolog Serial YES AdvancedDDE Client (10)

OPC Client (10) Enron PLC Serial YES AdvancedDDE Client (3) Echelon LonWorks YES OPC Client (21) LonWorks YES OPC Client (39) Eurotherm Drives N/A DDE Client (8) 800 Series EI-Bisync YES OPC Client (41) Event Technologies

Gello YES OPC Client (28)

Festo PLC

405 Series Serial YES AdvancedDDE Client

Communications (16) Fieldbus Open Fieldbus YES OPC Client (37) YES OPC Client (23) YES OPC Client (24) Fischer & Porter MICRO-DCI Serial YES OPC Client (11)

FANUC Spares




Manufacturer Device Protocol NT Communications Product Fisher-Rosemont ROC364, ROC312,

ROC407 RS-232 YES AdvancedDDE Client

Communications (3) Delta-V

PROVOX YES OPC Client (9)

Axs4 YES DDE Client (31) Provox Ethernet YES DDE Client (13) Univox

MicroProvox Provox

Serial YES DDE Client (13)

RS3 RNI, RS3 SCI RS-232 YES OPC Client (41) FloPro FloNet YES FloPro Communications

Part No: IC646NEF000 Foxboro I/A Series TCP/IP YES OPC Client (41) 760 series Serial YES OPC Client(3) GE 3720 Power Meter Serial YES MODBUS RTU

Communications Part No: IC646NMR000

DDP, DFM, DLP Tasnet NIM YES TASNET NIM Interface (19) GE Fanuc Series 90™ Ethernet YES Series 90™ Ethernet

Provided with Server Series 90™

Series Six Genius Blocks

GENIUS® YES GENIUS Communications Provided with Server

Field Control Series 90™

Series 90 Micro Series 90™ SNP/SNP-X

YES Series 90™ SNP Provided with Server

Series 90 SNP-X via dial-out modems

YES AdvancedDDE Client Communications (3)

Series 90™ Series Six Series Five

CCM-2 YES CCM-2 Communications Provided with Server

OCS CsCAN YES OPC Client Note: Requires CsCan

Interface (IC320CGM500) and OCS OPC Server (IC320CGM510)

GEC KCEG140, KVAR, LFCB102

Tasnet NIM YES TASNET NIM Interface (19)

Giddings &Lewis PLC ARCNET YES AdvancedDDE Client Communications (3)

Harris RTU DNP 3.0 YES Call for availability Hitachi S10 Series Serial YES DDE Client Communications

(17)



Manufacturer Device Protocol NT Communications Product Hewlett Packard 3396 Integrator Serial YES AdvancedDDE Client

Communications (3) Honeywell IPC 620 Serial YES Honeywell IPC 620

Communications Part No.: IC646NGM000

TDC-2000 Data Hiway via PCNM

YES OPC Client (17)

TDC-3000 Local Control Network

YES OPC Client (17)

DRP 3000 Serial YES OPC Client (17) UDC 3000 UDC 5000 UDC 3300 Serial YES Use Modbus RTU

Part No.: IC646NMR000 45000 Ethernet YES OPC Client (17) S9000E, 620LC, Ethernet YES OPC Client (17) IPC620 SDS YES OPC Client (23) TotalPlant YES OPC Client (36) Interbus-S Open Interbus-S YES OPC Client (26) YES OPC Client (24) YES OPC Client (23) Intermec Bar Code Reader YES DDE Client Communications

(5) Bar Code Printer YES DDE Client Communications

(5) IDEC Computer Link YES AdvancedDDE Client (10) OPC Client (10) Johnson Controls DX9100

Unitary Ctrls. N2 YES Johnson Controls N2 Bus

Communications Part No:IC646NGJ000

Keithley Metrabyte YES OPC Client (17) Kimray RTU YES OPC Client (17) Kloeckner-Moeller

PS306, PS316 SucomA YES OPC Client (26)

PS4 Serial YES OPC Client(11) Koyo DL Series DirectNet YES AdvancedDDE Client (10)

OPC Client (10) SG, SL, and DL

Series K Sequence YES AdvancedDDE Client (10)

OPC Client (10) Landis & Gyr Gyr-8979RTU, MPS-

9000 Tasnet NIM YES

TASNET NIM Interface (19)

Landis & Staefa APOGEE System Ethernet YES OPC Client (38)

FANUC Spares




Manufacturer Device Protocol NT Communications Product Leeds & Northrup Micromax 2 RS-485 YES OPC Client (17) LonWorks LonWorks YES OPC Client (21) LonWorks YES OPC Client (39) Magnetek GPD 515 Drives Serial YES AdvancedDDE Client (10)

OPC Client (10) Merlin Gerin Batibus YES OPC Client (26) Mitsubishi A2A, A3U, A4U TCP/IP YES Mitsubishi TCP/IP

Communications Part No: IC646NGB000

A-Series Serial YES Mitsubishi A-Series Serial Communications Part No: IC646NME000

FX, FX0, FX0n, FX2C

RS-232,and FX NET RS-485

YES AdvancedDDE Client (10) OPC Client (10)

MMS Open Ethernet YES OPC Client Modicon 984, 884, 384, 584,

184, M84 Quantum

Modbus RTU

YES Modbus RTU Communications Part No: IC646NMR000

984, 884, 384, 584, 184, M84 Quantum

Modbus Plus YES Modbus Plus Communications Part No: IC646NMD000

Modicon Quantum TCP/IP YES Modbus TCP/IP Communications Part No: IC646NMX000

Modbus RTU Slave

YES AdvancedDDE Client (10) OPC Client (10)

Modbus RTU/ASCII with Dial-out Modem support

YES AdvancedDDE Client Communications (3)

Modular Data Systems

ADACS UAP YES OPC Client (41)

Moore APACS TCP/IP YES OPC Client (42) Local Instrument

Link via ICI-320 YES OPC Client (17)

MYCRO YES OPC Client (41) Motorola Moscad Serial YES AdvancedDDE Client

Communications (3) National Instruments

Fieldpoint YES OPC Client (27)

E Series DAQ Boards

YES OPC Client (27)



Manufacturer Device Protocol NT Communications Product OMRON CV-Series TCP/IP YES OMRON TCP/IP

Communications Part No: IC646NGT000

C-Series CV-Series

Host Link YES OMRON Host Link Communications Part No: IC646NGL000

C-Series, CV-Series, Alpha

Sysmac Link YES AdvancedDDE Client Communications (4)

Open Open Serial, Ethernet YES Descartes Omniserver Part No: IC646NDS000 (development), IC646NDS300 (run-time)

Open Serial YES DDE Client Communications

(18) Marquee Serial YES Marquee Driver

Part No.: IC646NMA000 CANOpen YES OPC Client (23)

OPC Client (24) Open DeviceNet YES OPC Client (25) YES OPC Client (24) YES OPC Client (23) YES AdvancedDDE Client (14) Open Fieldbus YES OPC Client (37), (23), (24)

Open Interbus-S YES OPC Client (26) Opto-22 Opto-22 Controllers AC37, Arcnet,

Ethernet, Serial YES AdvancedDDE Client (12)

OPC Client (12) Optomux RS-422 YES OPC Client (29)

OPC Client (11) Brain Board RS-422 YES AdvancedDDE (3) Phoenix Interbus-S YES AdvancedDDE Client

Communications (6) PLC Direct DL230/240

DL330/340 DL430/440

DirectNET YES AdvancedDDE Client Communications (10)

K Sequence YES AdvancedDDE Client

Communications (10)

FANUC Spares




Manufacturer Device Protocol NT Communications Product Profibus DP Master, PPI,

FMS YES OPC Client (26)

DP Master, PPI, FMS,

YES OPC Client (26), (32)

DP Slave YES OPC Client (25), (32) DP YES OPC Client (30), (24), (32) YES OPC Client (44)

TASNET NIM Interface (19) Redac 70H Tasnet NIM YES

Reliance Automax Ethernet YES AdvancedDDE Client Communications (1)

PCLink YES AdvancedDDE Client Communications (14)

SAIA SBUS YES OPC Client (26) SATT Control PLC SattBus Network N/A AdvancedDDE Client

Communications (14,2) Schlumberger Meters Tasnet NIM YES TASNET NIM Interface (19) Seriplex Seriplex I/O Seriplex Bus YES Seriplex I/O Communications

Part No:IC646NSX000 Sharp PLC TCP/IP YES Sharp TCP/IP Communications

Part No: IC646NGS000 Siemens/TI TI-505/525

TI-5x5 Serial RS-232 YES Siemens/TI Communications

Part No.: IC646NTN000 TI-5x5

TI Direct Serial RS-232

YES OPC Client (26)

TI-545

Ethernet H1 YES OPC Client (26)

TI-5x5 TCP/IP YES OPC Client (29) TI-5x5 TIWAY Host

Adapter via RS-232

YES OPC Client (10) AdvancedDDE Client (10)



Manufacturer Device Protocol NT Communications Product Siemens S5 3964, 3964R YES AdvancedDDE Client

Communications (14,2) S5 3964, 3964R YES OPC Client (26) S5 AS511 YES OPC Client (26) S5 Sinec® H1 YES OPC Client (26) S5 Sinec® L2/S5 YES OPC Client (26) S5, S7 Profibus FMS YES OPC Client (26) S5 Profibus DP YES OPC Client (26) S7-300/400 Profibus MPI YES AdvancedDDE Client (2) S7-200 Profibus PPI YES OPC Client (26) S7-200 Profibus PPI YES OPC Client (10) LSX TCMS TCP/IP YES OPC Client (41) Drives RS-232/485 YES DDE Client (3), (11) Siemens Landis Division

APOGEE System Ethernet YES OPC Client (38)

Square/D SY/Max SY/Net YES Square/D Communications

Part No.: IC646NQD000 Tasnet Various Serial to Network

Interface YES TASNET NIM Interface (19)

Telemechanique Uni-Telway YES OPC Client (26) EthWay YES OPC Client (26) FIPWAY® YES OPC Client (26) Toshiba T-Series,

EX-Series Serial YES AdvancedDDE Client (10)

OPC Client (10) Total Control Products, Inc

Marquee RS-232 YES Marquee Driver Part No.: IC646NMA000

Toyoda Toyopuc Ethernet YES Toyopuc Ethernet

Communications Part No: IC646NTY000

Triconix Tricon TCP/IP YES OPC Client (41) TRW 9550 TASNET NIM YES TASNET NIM Interface (19) UTICOR Technology

Marquee RS-232 YES Marquee Driver Part No.: IC646NMA000

Valmet CQ-120 Serial YES OPC Client (41) Micro 1C Serial YES OPC Client (41) DAMATIC XD Ethernet YES OPC Client (11) Series 3, Series 5 Tasnet NIM YES TASNET NIM Interface (19) West Instruments West Series 3010 Rs-232 YES OPC Client (41)

FANUC Spares




Manufacturer Device Protocol NT Communications Product Westinghouse PC700/900

PC1100/1200 NL1075

Serial YES AdvancedDDE Client Communications (16)

Yokogawa Micro-XL Serial YES OPC Client (17) Chart Recorder Serial YES OPC Client (17) Centus-CS TCP/IP YES OPC Client (41)



Third Party OPC/DDE Servers and CIMPLICITY Drivers GE Fanuc provides the following list of companies that offer OPC Servers, DDE Servers and CIMPLICITY Drivers as a reference for users of CIMPLICITY Software. The companies listed below sell and support products that communicate with various manufacturing devices. Contact these companies directly for detailed product information, availability, pricing, and support. The CIMPLICITY DDE (Dynamic Data Exchange) Client communications software supports the exchange of data with DDE Servers. CIMPLICITY DDE is compatible with applications that follow Microsoft’s standard for DDE Communications. CIMPLICITY is also compatible with DDE Servers that support the AdvancedDDE standard and these servers provide better throughput. Companies that support AdvancedDDE are identified with an (*). CIMPLICITY OPC Client Communications supports OPC Servers that adhere to the v1.0A or v2.0 Data Acquisition specification published by the OPC Foundation.

1 Advanced Engineering, Inc * 513 Autumn Springs Court. Franklin, Tenn. 37067 (615) 771-6500 (615) 771-6501

2 ATS Applied Tech Systems B.V. * P.O. Box 4993 2003 EZ Haarlem, The Netherlands [email protected] + 31 23 5 35 25 44

3 Automation Solutions * 930 Gemini Houston, TX 77058 (281) 286-6017

(281) 286-6902 (fax)

4 CimQuest (609) 293-1115 *

(609) 293-1116 (fax) http://www.cimquest.com

5 Data Technologies P.O. Box 5820 Linwood, WA 98046 (206) 776-5729 (206) 776-5720 (FAX)

6 DiCam Inc* 21301 Powerline Rd. #309 Boca Raton, FL. 33433 (561) 487-1880 (561) 487-8126

FANUC Spares




7 Echelon 4015 Miranda Avenue Palo Alto, CA 94304 (415) 855-7421 (415) 855-6153

8 Eurotherm Drives, Inc 9225 Forsyth Park Drive Charlotte, NC 28273 704 588-3246 704 588-3249 (fax)

9 Fisher Controls International Inc. P.O. Box 190 Marshalltown, IA 50158 515-754-3011 www.fisher.com

10 KEPWare, Inc. * 25 Bridge Street Yarmouth, Maine 04096 (207) 846-5881 (207) 846-5947 http://www.kepware.com

11 Klinkmann Automation P.O Box 38 SF-00371 Helsinki, FINLAND + 358 0 513 322 + 358 0 513 541 (FAX)

12 Opto-22 *

43044 Business Park Drive Temecula, CA (909) 695-9299

13 Qualitrol Software Toolbox *

3030-B Whitehall Park Drive Charlotte, NC 28273 1-888-665-3678 704-587-9767 (fax) 704-587-9545 (interntional) http://www.softwaretoolbox.com

14 Rockwell Software *



15 RoviSys Company

1455 Danner Drive Aurora, Ohio 44202 (216) 562-8600

16 Specter Instruments *

3913 Todd Lane Bldg. 104 Austin, TX 78744 512 326-1011 512 326 1019 (fax) http://www.specterinstruments.com

17 Standard Automation and Control 2450 South Shore Blvd. Suite 100 League City, TX 77573 (281) 334-3293 (281) 334 4324 (fax) http://www.stdauto.com

18 TAL Technologies Software Wedge 2027 Wallace Street Philadelphia, PA 19130

(215) 763-7900 (215) 763-9711 (FAX)

19

TASNET, Inc. 5271 102nd Ave North Pinelas Park, FL 33782 (813) 544-1555

20 ABB Instrumentation 1175 John Street West Henrietta, NY 14586 (716) 292-6050 www.abb.com

21 Innovex Technologies 526 Braddock Avenue Turtle Creek, PA 15145 (412) 829-7279 (412) 829-7405 (FAX) www.innovextech.com

22 Bristol Babcock 1100 Buckingham Street Watertown, CT 06795 (860) 945-2200 www.bristolbabcock.com

FANUC Spares




23 Hilscher GMBH Rheinstrasse 78 Hattersheim Germany + 49 6190-99070 www.hilscher.com

24 Synergetic Microsystems Inc. 2506 Wisconsin Avenue Downers Grove, IL 60515 (630) 434-1770 www.synergetic.com

25 SST Industrial Communication Technologies 50 Horthlan Road Waterloo, Ontario Canada N2V 1N3 (519) 725-5136 www.sstech.on.ca

26 Applicom International

One Hallide Plaza Suite 505 San Francisco, CA 94102 (415) 956-1665 http://www.applicom-int.com

43, rue Mazagran 76320 Caudebac-les-Elbeuf France + 33 2 32 96 04 20

27 National Instruments 11500 B North Mopac Expressway Austin TX 78759 Canada N2V 1N3 512-794-0100 www.natinst.com

28 Event Technologies, Inc 10521 West Forest Home Ave Hales Corners WI 53130 414-427-8002 www.gello.com

29 Eldridge Engineering 708 W. 20th Avenue Spokane, WA 99203 509-838-7517 www.eldridgrrng.com

30 Softing GMBH Richard-Reitzner-Allee 6 Haar Germany D85540 +49 89-4565-6362 www.softing.com

31 Fisher Rosemount Systems 12000 Portland Avenue South Burnsville, MN 55337 (612) 895-2000



32 ifak system GMBH Steinfeldstrasse 3 39179 Barleban, Germany + 49 39203-81920 www.ifak-system.com

33 ABB Industrial Systems, Inc P.O. Box 22685 Rochester, NY 14692-2685 (716) 273-7246 www.advantocs.com

34 ABB Industrial Systems, AB S-721 67 Vasteras Sweeden + 46 21 34 00 00 www.advantocs.com

35 Elsag Bailey Process Automation 29801 Euclid Avenue Wickliffe, OH 44902 (509) 838-7517 www.ebpa.com

36 Honeywell Inc Industrial Automation and Control 16404 N. Black Canyon Highway Phoenix, AZ 85023 (602) 313-5586 www.iac.honeywell.com

37 Smar Equipamentos Industriais Ltda.

Av. Antonio Furlan Jr., 1028 Sertaozinho - SP - Brasil CEP 14.160-000 +55 16 645 3599 http://www.smar.com

38 Siemens Building Technologies, Landis Division Buffalo Grove, IL Christopher Hollinger (847) 215-1000 Ext. 5991 e-mail: [email protected]

39 Gesytec Pascalstraße 6 52076 Aachen, Germany Tel.: + 49 (2408) 944-0 http://www.gesytec.de

FANUC Spares




40 SISCO 6605 19½ Mile Road Sterling Heights, MI 48314-1408 Tel: (810) 254-0020 Fax: (810) 254-0053 http://www.sisconet.com

41 MATRIKON CONSULTING INC. 510, 10216-124 Street Edmonton, Alberta Canada T5N 4A3 Tel: (780)448-1010 Fax: (780)448-9191 http://www.matrikon.com

42 Moore Process Automation Solutions 1201 Sumneytown Pike Spring House, PA 19477-0900 Tel: (215) 646-7400 Fax: (215) 283-6358 http://www.mooreproducts.com

43 Applicon Intl. One Hallide Plaza Suite 505 San Francisco, CA 94102 (415) 956-1665 http://www.applicom-int.com

43, rue Mazagran 76320 Caudebac-les-Elbeuf France + 33 2 32 96 04 20

44 AG-E GMBH Dennewartst. 27 D-52068 Aachen Germany

http://www.ag-e.coms Phone: (49) 241-90 39 000 Fax: (49) 241-90 39 007

45 Beckhoff Automation LLC 3000 Campus Drive Minneapolis, MN 55441 Tel: (612) 694-2300 Fax: (612) 694-2399 http://www.beckhoff.com

46 Bentley Nevada Corporation 1617 Walter Street Minden, Nevada 89423 Tel: (702) 782-3611 Fax: (702) 782-9253 http://www.bently.com



47 Northern Dynamics J103-155 Frobisher Drive Waterloo, Ontario Canada N2V 2E1 Tel: (519) 725-2071 Tel: (519) 725-2072 http://www.nordyn.com

FANUC Spares




Allen-Bradley Communications CIMPLICITY® Allen-Bradley Communications software provides communications to Allen-Bradley PLCs over a variety of communications media. High speed Ethernet connections as well as Data Highway Plus networks are supported. Cable Redundancy to PLC-5 devices is supported in Data Highway Plus networks through dual interface cards.

Sample Ethernet Networ2k

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays PLC-2 and PLC-3 are registered trademarks and RSLinx is a trademark of Allen-Bradley Company, Inc.

Supported Devices Allen-Bradley PLC-5 Allen-Bradley SLC-5/04, 5/05 Allen-Bradley PLC-2® Allen-Bradley PLC-3® Allen-Bradley PLC-5/250 (Pyramid Integrator)

Supported Networks Ethernet Data Highway Plus (via 1784-KTX & 1784-KT) Data Highway Plus Cable Redundancy ControlNet via a ControlLogix Gateway

Supported PLC Data PLC-2:

Read/Write: Register memory PLC-3:

Read/Write: D, A, H, S, N, F, B, I, O, T, and C files

PLC-5: Read/Write: D, A, N, F, B, S, I, O, T, C,

and R files SLC-5/04:

Read/Write: A, N, B, S, T, C, and R files

Required Computer Software Rockwell Software RSLinx™ (Rockwell Software Part: 9355-WABOEM)

Required Computer Hardware For Data Highway Plus: Allen-Bradley 1784-KTX or 1784-KT For Ethernet: a standard Ethernet interface Sample Data Highway Network

Computer

5/250 PLCHostname: P1B1

Ethernet

540E PLCHostname: 540EA1

Data Highway Plus Network

PLC 3(17)

1785KA(71)

RM KA

1785KA(72)

PLC 2(4)

Data Highway Network

Data Highway Network

PLC 5(31)

Data Highway Plus Network

Computer

Single or Redundanct Data Highway Plus Network

PLC 5 PLC 5



Allen-Bradley Data Highway Plus Communications CIMPLICITY® Allen-Bradley Data Highway Plus Communications software provides communications to Allen-Bradley PLCs Data Highway Plus via the 1784-KT/B interface. Up to six 1784-KT/B interface cards can be used to communicate with six Data Highway Plus networks.

The product allows you to easily configure the 1784-KT/B interface card and communications parameters. An installation verification program gives you immediate read/write access any PLC on the Data Highway Plus LAN.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data ✓ Analog Deadband ✓ Engineering Units Conversion ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays PLC-2 and PLC-3 are registered trademarks of Allen-Bradley Company, Inc.

Supported Devices Allen-Bradley PLC-5 Allen-Bradley SLC-5/04 Allen-Bradley PLC-2® Allen-Bradley PLC-3® Allen-Bradley PLC-5/250 (Pyramid Integrator)

Supported Networks Data Highway Plus (via 1784-KT/B) 1785-KA Bridges

Supported PLC Data PLC-2:

Read/Write: Register memory PLC-3:

Read/Write: N, I, O, F, B, T, and C files PLC-5:

Read/Write: N, I, O, F, B, T, and C files SLC-5/04:

Read/Write: N, B, T, and C files

Required Computer Software None

Required Computer Hardware Allen-Bradley 1784-KT/B Data Highway Plus interface

Sample Network

5/25 PLC 1785-KA

5/30 PLC

Data HighwayBridge

Data Highway Plus

Data Highway Plus

FANUC Spares




Allen-Bradley DF-1 Communications CIMPLICITY® Allen-Bradley DF-1 Communications software provides communications to Allen-Bradley PLCs via a Serial RS-232 connection and over DH-485 or Data Highway plus via protocol converters.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads

Unsolicited Data ✓ Analog Deadband ✓ Engineering Units Conversion ✓ Alarm on Communications Failure

Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays

Sample Network

PLC-2 and PLC-3 are registered trademarks of Allen-Bradley Company, Inc.

Supported Devices Allen-Bradley PLC-5 Allen-Bradley SLC-500 Series Allen-Bradley PLC-2® Allen-Bradley PLC-3®

Supported Networks RS-232 DH-485 via 1770-KF3 Data Highway plus via 1770-KF2

Supported PLC Data PLC-2, PLC-3:

Read/Write: Register memory PLC-5, SLC-500

Read/Write: N, F, B, I, O, S,T, C


Required Computer Hardware Available Serial Port

RS-232 SLC-500

1770-KF2

RS-232

Data Highway Plus

PLC-5PLC-5



Allen-Bradley Intelligent Antenna Communications CIMPLICITY® Allen-Bradley Intelligent Antennas Communications software provides communications to Allen-Bradley 2750-AS antennas as part of a Radio Frequency Identification (RFID) system. Communications via the Antenna can be used to download antenna setup parameters and to read or write data to compatible RF Tags and part of a Work in Process monitoring system. Communications between CIMPLICITY HMI and the antennas is supported both through the local serial port and over TCP/IP via Terminal Servers.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Alarm on Communications Failure ✓ Communication Statistics


Supported Devices Allen-Bradley 2750-AS Antennas

Supported Networks RS-232 TCP/IP via Terminal Servers

Supported Device Data Read Only Tags Read/Write Tags Programmable Tags Configuration Settingss


Required Computer Hardware None

Sample Network

FANUC Spares




Applicom® Communications for Siemens, Telemecanique, and other PLCs CIMPLICITY® Applicom Communications software provides communications to a broad range of PLCs using the manufacturers protocol over a variety of communications media. High speed Ethernet, Profibus, and FIPWAY® connections as well as serial networks are provided. Network access is achieved using Applicom network interfaces which include high speed on-board processors that manage the protocols and off-load the host CPU to improve system performance.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays Supported Devices Siemens S5/S7 Siemens/TI Telemecanique Klockner Moeller OMRON SAIA

Supported Networks Ethernet Profibus FIPWAY® Serial - RS-232,RS-422 CAN InterBus Applicom is a registered trademark of Applicom International Sinec is a registered trademark of Siemens AG

Supported Protocols SINEC® L2/S5 SINEC® H1 ETHWAY® FIPWAY® Profibus FMS Profibus DP Profibus MPI/PPI Interbus-S 3964/3964R MODBUS UNI-TELWAY SYSMAC-WAY SUCOMA DATALINK CAN

Required Computer Software Applicom protocol licenses are required for the protocols you use. Contact Applicom for the appropriate licenses.

Required Computer Hardware An Applicom interface card is required for all applications using these protocols. The required hardware depends on the selected protocol:

Protocol Interface Card

3964/3964R (Siemens) AS511 (Siemens Programmer .Port) MODBUS (Modicon) UNI-TELWAY (Telemecanique) SYSMAC-WAY (Omron) SUCOMA (Klockner Moeller) TI Direct (Siemens/TI) Profibus PPI

PC-1000 (1 port) PC-4000 (4 ports)

Sinec® L2/S5 (Siemens) Profibus FMS (Siemens) Profibus DP Profibus MPI

PC1500PFB

Sinec H1 (Siemens and Siemens/TI) ETHWAY (Telemecanique)

PC2000ETH

InterBus PCI2000IBS CAN PCI2000CAN FIPWAY® (Telemecanique) PC2000FIP

Contact Applicom Intl. to purchase required hardware and software products

USA: Applicon Intl. One Hallide Plaza Suite 505 San Francisco, CA 94102 (415) 956-1665 www.applicom-int.com

France: 43, rue Mazagran 76320 Caudebac-les-Elbeuf France + 33 2 32 96 04 20



CCM2 Communications The CIMPLICITY® CCM2 Communications software provides communications to GE Fanuc PLCs and over a serial communications link. Point to point and multi-drop configurations are supported. CIMPLICITY functions as a CCM2 master device. CIMPLICITY® CCM2 Communications supports master-slave configurations where CIMPLICITY HMI operates as the master.



POWER SUPPLY

SERIES 90-7 0

LOGIC POWEROK CH 1 O K

CPU 7 31 BUS TRANS- MIT TER

PROGRAM- M ABLE COPRO- CESSOR

GENI US BUS

CONT RO L- LER GE Fanuc

M ABLE

INPUT 120 VAC

OUT PUT 12 0VAC,O5 A

INPUT 120 VAC

INPUT 120 VAC

OUT PUT 120VAC,O5A

ENABLEDRUNOK

USER 2USER 1OKPG MR

BUS

PROGRAM-

CONTROLL ER

RS-422 Multi-drop

POWER SUPPLY

SERIES 90-7 0

LOGIC POWEROK CH 1 O K

CPU 7 31 BUS TRANS- MIT TER

PROGRAM- M ABLE COPRO- CESSOR

GENI US BUS

CONT RO L- LER GE Fanuc

M ABLE

INPUT 120 VAC

OUT PUT 12 0VAC,O5 A

INPUT 120 VAC

INPUT 120 VAC

OUT PUT 120VAC,O5A

ENABLEDRUNOK

USER 2USER 1OKPG MR

BUS

PROGRAM-

CONTROLL ER

Series Five, Series Six and Series 90 are trademarks of GE Fanuc Automation, North America, Inc.

Supported Devices GE Fanuc Series Six™ GE Fanuc Series Five™ GE Fanuc Series 90-30 GE Fanuc Series 90-70

Supported Networks RS-232 RS-422 Multi-drop

Supported PLC Data Series 90:

Read/Write: Register, Input, Output

Series Six:

Read/Write: Register, Input, Output, Input Override, Output Override

Series Five:

Read/Write: Register, Local Input, Local Input Override, I1/I2+ Input, I1/I2+ Input Override, Special Input, Local Output, Local Output Override, O1/O2+ Output, O1/O2+ Output Override, Internal Coils 01, Internal Coils 01 Override, Internal Coils 02, and Internal Coils 02 Override


Required Computer Hardware Available serial communications port

FANUC Spares




DDE Client Communications CIMPLICITY® DDE Client Communications provides the ability to integrate third party DDE I/O Servers with CIMPLICITY HMI for data acquisition. The DDE Client supports both standard DDE (CF_TEXT format) and AdvancedDDE™. AdvancedDDE provides significantly higher throughput than standard DDE. With this capability, CIMPLICITY HMI expands its reach to dozens of additional manufacturing devices through standard and AdvancedDDE I/O Servers from device manufacturers and third party software suppliers.

MMI products have always relied on third parties to develop drivers for the wide variety of proprietary communications protocols that exist. Approximately 80% of all available MMI I/O communications drivers are supplied by third parties. AdvancedDDE is he choice of many developers because it is an open standard supported by other packaged software applications.

The CIMPLICITY DDE Client communicates to DDE I/O Servers using the standard Application, Topic, and Item conventions for DDE. The Application and Topic are specified as part of CIMPLCICITY Device configuration and the Item is specified as the Address for the point in CIMPLICITY Point configuration. AdvancedDDE is a trademark of Rockwell Software, Inc.

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text

Supported DDE Servers DDE I/O Servers for Windows 95 or Windows NT that support CF_TEXT or AdvancedDDE formats

Supported Protocols DDE (CF_TEXT) NetDDE AdvancedDDE

Required Computer Software None required for CIMPLICITY DDE Client Communications. Requirements for 3rd Party DDE Servers will vary.

Required Computer Hardware None required for CIMPLICITY DDE Client Communications. Requirements for 3rd Party DDE Servers will vary.



Descartes Systems OmniServer™ OmniServer is a tool for developing communications protocols to a broad variety of I/O devices. Protocols are developed without any programming simply by specifying the protocol details. OmniServer interfaces to CIMPLICITY HMI via AdvancedDDE™ to provide high data throughput. OmniServer Developer with Protocol Editor is used to create custom protocols. The protocol editor creates a protocol definition file which can be used with either OmniServer Developer or OmniServer Run-time products to communicate with devices. Once protocols are developed with OmniServer Developer, the protocol definition file can be transferred to a system with OmniServer Run-time for communications from that system. OmniServer provides these great features: Polling and Unsolicited Messaging – OmniServer can be set up to listen for, and reply to, unsolicited messages from a device. OmniServer can also issue requests to a device and process the responses on a periodic basis (polled) or on command (triggered) from CIMPLICITY HMI. Both polled and unsolicited messaging can be supported in the same protocol. Read and Write Access OmniServer will read data from the device and pass it on to CIMPLICITY HMI. OmniServer also accepts setpoints from CIMPLICITY and writes them to the device. Point to point and Multi-drop configurations OmniServer protocols can support multiple devices on a single port. Each device is simply configured as a separate DDE topic. Built in error detection algorithms OmniServer includes a variety of error detection schemes including checksums, CRCs, and LRCs. Select any of the available calculations to

use in your messages as required without any programming. ASCII or Binary protocols OmniServer recognizes both ASCII and binary-based protocols. Comprehensive Data types OmniServer supports integer and real numbers as well as discrete (Boolean) values and character strings. Many data formats can be specified in the protocol including decimal, hexadecimal, binary-coded decimal, and IEEE floating point format. Data Integrity OmniServer supports a communications status flag for each DDE topic. The status flag can be monitored by an HMI application to alert users in case of a communications failure. DDE and AdvancedDDE Support OmniServer supports AdvancedDDE to provide fast communications between the DDE Server and the CIMPLICITY Communications Client. OmniServer data can also be viewed in Excel and other Windows® applications that provide access to DDE data. Serial port and TCP/IP connections OmniServer can be used over standard serial ports or with Winsock TCP/IP networks. OmniServer can also be used with multi-port cards such as DigiBoard. Up to 16 serial ports can be used. OmniServer is ideal for developing the simple protocols required by Bar Code Readers, Loop Controllers, Scales, Relays and many other I/O devices. Once your protocol has been developed, OmniServer runs as an AdvancedDDE™ Server and integrates with CIMPLICITY HMI via DDE Client Communications which is included as a standard feature of CIMPLICITY HMI Server. OmniServer is available for Windows 95 and Windows NT® (Intel) platforms.

FANUC Spares




FloPro FloNet Communications CIMPLICITY® FloPro/FloNet Communications software provides communications to PCs with FloNet communications interfaces running FloPro applications over an Ethernet LAN. FloPro is a control logic engine that uses flow-chart based programming in place of ladder logic. FloPro communicates to CIMPLICITY HMI via a special interface card across 10/Base-T Ethernet physical interconnections. This card is referred to by its model number (IPN-200) or as a FloNet card. The physical network it communicates across may be referred to as the Ethernet or as FloNet.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32 bit) ✓ 4 digit unsigned BCD ✓ Digital ✓ Arrays

Sample Network

Supported Devices PCs equipped with FloNet cards running version 1.14 firmware, and FloPro version 2.774, including model/capacity variants FloPro/64, FloPro/256, FloPro/512, FloPro/1024, FloPro/4096 and FloPro/6144 are supported locally via an Ethernet link.

Required PLC Network Device FloNet IPN-200 interface cards

Supported PLC Data Input Output Flag Input Force Output Force Flag Force Counter Register Number ASCII Timer: Limit, Current value

Required Software None

Required Computer Hardware Standard Ethernet Interface



Genius®Communications CIMPLICITY® Genius® Comm unications provides communications to GE Fanuc Series 90™ and Series Six PLCs and Genius Blocks over a high speed Genius LAN. The product’s 32-Bit Windows 95 and NT drivers provide top performance and reliability .

Configuration is simplified by the Graphic User Interface and communications can be verified with programs that display all devices and global data on the network.

Genius Blocks can be monitored directly from CIMPLICITY HMI without a PLC; Analog and Digital blocks can be controlled. In this configuration, circuit faults from Analog and Digital blocks can be reported directly to CIMPLICITY software for alarming, logging and graphic display.


Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays Genius is a registered trademark and Series Six and Series 90 are trademarks of GE Fanuc Automation, North America, Inc.

Supported Devices GE Fanuc Series 90-70 PLCs GE Fanuc Series 90-30 PLCs GE Fanuc Series Six PLCs Genius Blocks Field Control (Q2 97) For fault data: IC660BBD020, IC660BBA100

Supported Networks Genius


Read/Write: %AI, %AO, %I, %M, %Q, %R, %S, %SA, %SB, %SC

Read: Global Data Series Six

Read/Write: Register, Input, Output Read: Global Data

GENIUS Blocks:

Read/Write: Inputs, Outputs Read: Circuit & Block Faults


Required Computer Hardware PCIM Interface Card:

IC660ELB906, IC660ELB921, IC660ELB922

Sample Network

POWER SUPPLY

SERIES 90-70

LOGIC POWEROK CH 1 OK

CPU 731 BUS TRANS- MITTER

PROGRA M- MABLE COPR O- C ESSOR

GENIUS BUS

CONTROL- LE R GE Fanuc

MABLE

INPUT 120 VAC

OU TPUT 120VAC,O5A

INPUT 120 VAC

INPUT 120 VAC

OUTPU T 120VAC,O5A

EN AB LEDRUNOK

USER 2USER 1OKPGMR

BUS

PROGRAM-

CONTROLLER

GENIUS LanPOWER SU PPLY

SE RI ES 90-70

LOGIC POWE ROK CH 1 OK

CPU 731 BU S TRANS- MITTER

PROGRAM- MABLE COPRO- CESSOR

GE NI US BUS

CONTROL- LER GE Fanuc

MABLE

INPUT 120 VAC

OUTPUT 120VAC,O5A

IN PU T 120 VAC

I NPUT 120 VAC

OU TPUT 120V AC ,O5A

ENABLEDRU NOK

USER 2USER 1OKPGMR

BUS

PROGRA M-

CON TROLLER

GENIUS GENIUS GENIUS

FANUC Spares




Honeywell IPC 620 Communications Honeywell IPC 620 Communications provides access to Honeywell’s family of IPC 620 Programmable Controllers using the Asynchronous Byte Count (ABC) protocol. Up to 32 programmable controllers may be connected to CIMPLICITYHMI over a single multi-drop connection to a standard serial port


Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics


Supported Devices IPC 620-12 IPC 620-15 IPC 620-16 IPC 620-20 IPC 620-30

Supported Networks RS-232 RS-485

Supported PLC Data Digital Register Extended Register System Status Register

Required Computer Software Standard serial port

Required Computer Hardware 620-0048 DCM Module (revision VR3.1 or later) 620-0042 DCM Module (prom revision 21024L or later)



Johnson Controls N2 Communications CIMPLICITY® Johnson Controls N2 Communications software provides communications to Johnson Controls building automation devices over a serial communications link. This communications option supports both Johnson Controls N2 Open and DX9100 protocols.

The CIMPLICITY Johnson Controls N2 communications option operates as the master in point to point and multi-drop configuration which can support up to 255 devices.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32 bit) ✓ Unsigned Integer (8, 16, & 32 bit) ✓ Floating ✓ Text Modbus is a trademarks of Groupe Schneider, Inc.

Supported Devices Unitary Controllers DX9100 Digital Controller

Supported Network RS-485

Required Network Device MM-CVT101-0 RS-232 to RS485 converter

Supported Device Data Unitary Controllers

Read/Write: Analog Inputs Analog Outputs Binary output Internal Floating Point Data Internal Integer Data Internal Byte Data

Read Only: Binary Inputs Device Memory

DX9100 Digital Controller Read/Write: Login Results

Programmable Module Constants Programmable Module Logic Programmable Module Accumulator


Restrictions This option cannot be used with the Recipe Option


FANUC Spares




CIMPLICITY® Marquee Interface The CIMPLICITY Marquee Interface is a powerful and flexible tool that allows you to broadcast important production information to factory personnel on most marquee devices. With the Marquee driver you can display production data, alarm information, and informational messages. The Marquee Driver can display a set of messages. It will cycle through a queue of messages, displaying each message for a configured period. The messages for the marquee display are generated from alarm messages. The alarms may originate from points or from an alarm generated with CIMPLICITY Visual Basic extensions to the Basic Control Engine or with the Alarm Management API. The Marquee Driver configuration interface allows you to set up the serial interface to meet the requirements of the display device. Escape sequences and control characters can be configured to precede and/or follow each message. Control characters can be embedded in the messages that are displayed as well.

Supported Devices Most Marquees The Marquee Driver has been tested with Uticor and Total Control Product Marquees.



Production Count : 537Downtime : 1 M in 17 Sec

RS-232



Mitsubishi A Series Serial Communications CIMPLICITY® Mitsubishi A Series Serial Communications software provides an interface to Mitsubishi Series PLCs over serial link. Point-to-point and multi-drop configurations over RS-232 and RS-422 connections are supported. As many as 32 PLCs can be on a multi-drop link. CIMPLICITY HMI communicates directly to the A Series PLCs and to PLCs connected on a MELSECNET or MELSECNET/B network via a Computer Link Module.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure Host Redundancy Configurations ✓ Communication Statistics


Supported Devices AnA Series AnN Series A1S Series A2CCPUC24 A2CCPUC24-PRF

Supported Networks RS-232, RS-422 via: AJ71C24-S8, AJ1UC24, A1SJ71C24-R2, A1SJ71C24-R4, or equivalent.

Supported PLC Data Input X Counter (contact) C Output Y Counter (coil) C Internal Relay M Counter (preset value) C Latch Relay L Timer (preset value) T Step Relay S Data Register D Link Relay B Link Register W Annunciator F File Register R Special Relay M Special Register D Timer (contact) T Buffer Memory Timer (coil) T Parameter



CIMPLICITYHMI Server

RS-422

A-SeriesPLC

A-SeriesPLC

MELSECNET

A-SeriesPLC

FANUC Spares




Mitsubishi TCP/IP Communications CIMPLICITY® Mitsubishi TCP/IP Communications software provides an interface to Mitsubishi Series PLCs over a high speed Ethernet LAN using TCP/IP. CIMPLICITY can communicate directly to PLCs on the Ethernet LAN or to a Local Station PLC connected via MELSECNET. PLC data can be read periodically from the PLC and unsolicited updates are also supported.



Supported Devices

A0J2H A2A_S1 A2U_S1

A1 A2AS A3

A1N A2AS_S1 A3A

A1S A2C A3AU

A1SJ A2N A3M

A1S_S1 A2N_S1 A3N

A2 A2S A3U

A2_S1 A2S_S1 A3X

A2A A2U A4U

Supported Networks Ethernet

Supported PLC Data Data Register Link Register Files Register Input Output Internals Link Relay Annunciator Random Access

Required PLC Network Device Ethernet Interface Module type AJ71E71 or A1SJ71E71-B2

Required Computer Software TCP/IP Support


Computer

Ethernet Network

Mitsubishi-Melsec PLC

Melsecnet





Modbus RTU Communications CIMPLICITY® Modbus RTU Communications software provides communications to Modicon PLCs and other devices that support the Modbus RTU protocol. over a serial communications link. Point to point and multi-drop configurations are supported. CIMPLICITY HMI functions as a Modbus master device. Radio Modem configurations are supported through RTS/CTS flow control. Communications statistics on failures and retries are tracked and reported through CIMPLICITY Points for logging, display, and alarming.



Sample Network


RS-422

Modbus is a trademark of Groupe Schneider, Inc.

Supported Devices Modicon 184, 384, 584, 884, 984 Modicon M84, Quantum GE Fanuc Series 90 GE Fanuc Series Six

Supported Networks RS-232 RS-422 Multi-drop Radio Modems

Supported PLC Data Read/Write: Coils, Output

Registers Read: Inputs, Input

Registers



Radio Modem Configuration


FANUC Spares




Modbus Plus Communications CIMPLICITY® Modbus Plus Communications software provides communications to Modicon PLCs. over the high speed Modbus Plus LAN. The communications supports the use of bridges and multiplexors as well as the redundant dual port interface which provides a redundant cable connection to PLCs. The Modbus Plus driver can communicate asynchronously over 8 channels to achieve maximum throughput. And, unsolicited data from PLCs is supported and may be time-stamped with .01 second accuracy in the PLC to support sequence of event reporting.

The Graphic User Interface simplifies setup and quickly verifies communications to PLCs. Diagnostic functions display Modbus Plus network statistics.


Supported Data Types ✓ Signed Integer (8, 16, & 32 bit) ✓ Unsigned Integer (8, 16, & 32 bit) ✓ Floating ✓ Text ✓ Arrays

Supported Devices Modicon 184, 384, 584, 884, 984 Modicon M84, Quantum

Supported Network Devices Modbus Plus (up to 4 networks) SA85-000 (dual cards supported) SA85-002 (redundant, dual port) SM85-000 (Micro-channel) AT984 Bridge Plus

Supported PLC Data Read/Write: Coils, Output Registers Read: Inputs, Input Registers


Required Computer Hardware One of the following Modbus Plus interface cards:

SA85-000 (single channel) SA85-002 (redundant, dual port) SM85-000 (Micro-channel)

MODBUS Plus

Bridge Plus

Modbus PLUS, SA85, and SM85 are trademarks of Groupe Schneider, Inc.



Modbus TCP/IP Communications CIMPLICITY® Modbus™ TCP/IP Communications software provides communications to Modicon Quantum PLCs over an Ethernet LAN using TCP/IP protocol. Unsolicited data from PLCs is supported.

The Graphic User Interface simplifies setup and quickly verifies communications to PLCs by providing read/write access to Holding Registers. Diagnostic functions provide detailed communications statistics to PLCs to assist in debugging network issues.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Server Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32 bit) ✓ Unsigned Integer (8, 16, & 32 bit) ✓ Floating ✓ Text ✓ Arrays Modbus is a trademarks of Groupe Schneider, Inc.

Supported Devices Modicon Quantum

Required PLC Network Device NOE 211 000 TCP/IP Interface

Supported PLC Data Read/Write: Coils

Holding Registers Holding Registers (double precision) General Reference

Read Only: Discrete Inputs Input Registers

Supported Networks Ethernet Modbus Plus via TCP/IP to Modbus Plus Bridge

Required Software TCP/IP Support


FANUC Spares




OMRON Host Link Communications CIMPLICITY® OMRON Host Link Communications software provides communications to Omron C and CV Series PLCs over a serial Host Link System Network. Point to point and multi-drop configurations are supported via RS-232 and RS-422 to the built in CPU host communications interface or through an optional Host Link Unit. Up to 32 PLCs can be connected in a multi-drop configuration. CIMPLICITY HMI communicates directly to C-Series PLCs via C-Mode protocol and to CV-Series PLCs via CV-Mode or FINS protocol. Using FINS protocol CIMPLICITY software can also communicate to Controllers connected to a CV-Series Controller via a supported OMRON network for such as SYSMAC NET Link System or SYSMAC Link System



Supported Devices C20 C1000H CV500 C120/C500 CQM1 CV1000 C2000 C1000H CV2000 C2000H CPM1 CVM1-CPU01-E C200H C200HS CVM1-CPU11-E C200HX C200HE CVM1-CPU21-E

Supported Networks RS-232, RS-422

Supported PLC Data Core I/O (CIO) LR HR AR Timer Completion Flag Timer PV Counter Completion Flag Counter PV DM Area TR * CPU Bus Link * Expansion DM Area * Auxiliary Area * * supported in CV500, CVM1-CPU01-E, CV1000, CV2000 and CVM1-CPU11-E


Required Computer Hardware Available serial port

POWERSUPPLY

SERIES 90-70

LOGIC POWEROKCH 1 OK

CPU 731BUSTRANS-M ITTER

PROGRAM -M ABLECOPRO-CESSOR

GENIUSBUSCONTROL-LER

GE Fanuc

M ABLE

INPUT120 VAC

OUTPUT120VAC,O5A

INPUT120 VAC

INPUT120 VAC

OUTPUT120VAC,O5A

ENABLEDRUNOK

USER 2USER 1OKPGMR

BUS

PROGRAM -CONTROLLER

POWERSUPPLY

SERIES 90-70

LOGIC POWEROKCH 1 OK

CPU 731BUSTRANS-M ITTER

PROGRAM -M ABLECOPRO-CESSOR

GENIUSBUSCONTROL-LER

GE Fanuc

M ABLE

INPUT120 VAC

OUTPUT120VAC,O5A

INPUT120 VAC

INPUT120 VAC

OUTPUT120VAC,O5A

ENABLEDRUNOK

USER 2USER 1OKPGM R

BUS

PROGRAM -CONTROLLER

OMRON Network

RS-232

CV-SeriesPLC

C-SeriesPLC

Connection to C-Series PLC viaFINS protocol to CV-Series PLC

P OWER

S UP PLY

SE RI ES 90- 70


CPU 731 BUS

TRANS-

MITTE R

PROG RA M-

MA BLE

COP RO-

CESS OR

GE NI US

BUS

CONTRO L-

LE R GE Fanuc

MA BLE

INPUT

120 VA C

OUTPUT

12 0V AC,O5A

INPUT

12 0 VA C

INPUT

12 0 VA C

OUTP UT

12 0V AC,O5A

ENAB LE D

RUNOK

USER 2

USER 1OKPGMR

BUS

PROGRA M-

CONTROLLER

P OWER

S UP PLY

S ERIES 90-70


CPU 731 B US

TRANS-

MITT ER

PROG RA M-

M ABLE

COPRO-

CESS OR

GE NI US

B US

CONTRO L-

LE R GE Fanuc

M ABLE

INPUT

120 VA C

OUTPUT

12 0VA C,O5A

INPUT

120 VA C

INPUT

120 VA C

OUT PUT

12 0V A C,O5A

ENAB LE D

RUNOK

USER 2

USER 1OKPGMR

BUS

P ROGRAM-

CONT ROLLER

RS-422

CV-SeriesPLC

C-SeriesPLC

Direct Connection to C-Seriesor CV-Series PLCs



Omron TCP/IP Communications CIMPLICITY® OMRON™ TCP/IP Communications software provides communications to Omron CV-Series PLCs over an Ethernet LAN using TCP/IP protocol. This product also supports communications to C- and CV-Series PLCs on an OMRON network via a primary PLC on the Ethernet Network. A diagnostic program provides an easy way to test communications to the target PLCs.



Supported Devices CV500, CV1000, CV-2000, CVM1-CPU01-E, CVM1-CPU11-E, CVM1-CPU21-E C-Series controllers are supported via OMRON sub-networks (C200HSLK11/SLK21-V1 or C1000H-SLK11/SLK21-V1 SYSMAC LINK UNIT required):

C200H-CPU11-E C1000H-CPU01-EV1 C2000-CPU-EV1

Required PLC Network Device Omron Ethernet Interface

Supported PLC Data Read/Write

Core I/O (CIO) CPU Bus Link Area (G) Auxiliary Area (A) Timer Present Value (PV) Counter Present Value (PV) DM Area (DM) Expansion DM (E)

Read Only Timer Completion Flag Counter Completion Flag Temporary Relay Area (TR)



Sample Network

FANUC Spares




OPC Client Communications CIMPLICITY® OPC Client Communications provides the ability to integrate third party OPC I/O Servers with CIMPLICITY HMI for data acquisition. OPC is a new standard that builds on the success and strength of Microsoft Windows NT, Windows 95, and OLE (Object Linking and Embedding) technology. The design of OPC was begun in 1995, targeted at providing a standard for interoperability among control applications, field systems and devices, and business and office applications. OPC is endorsed by Microsoft and the OPC Foundation which developed the technical specification and which now includes over 140 members with broad representation from the process control industry including GE Fanuc Automation.

OPC defines a single common interface for both C++ and Visual Basic programs that is based on Microsoft’s Component Object Model (COM) and the Distributed Component Object Model (DCOM) to provide a common. Through this interface, software as diverse as Microsoft BackOffice, Human Machine Interfaces, and custom Visual Basic applications will all access process data with the same access methods.

OPC promises lower costs and increased productivity for end-users, systems integrators, and process control vendors alike by focusing communications issues on a single technology and strategy.

OPC’s benefits to the end user are:

• = Cost savings in application integration by providing a simple plug and play interface for multiple vendors

• = Communications technology that is superior to DDE. Although widely used, DDE is well known to be slow and unreliable.

• = Freedom to select vendors who provide the best of class solution rather than being captive to a single vendor with a proprietary product.

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text

Required Computer Software None required for CIMPLICITY OPC Client Communications. Requirements for 3rd Party OPC Servers will vary.

Required Computer Hardware None required for CIMPLICITY OPC Client Communications. Requirements for 3rd Party OPC Servers will vary.

HMI Run-timeDatabase

I/O Communications Network

OLE for ProcessControl

OPC replaces proprietarycommunications schemes for movingdata between HMIs and I/O Servers.Proprietary I/O Servers will be replacedby OPC I/O Servers that will typically besupported by device manufacturers.

OPC I/O Server

HMI System

HMI I/O Communications with OPC

OPC Client



Series 90™ Communications CIMPLICITY® Series 90™ SNP Communications software provides communications to GE Fanuc Series 90 PLCs over RS-232 and RS-485 serial links in point-to point and multi-drop configurations. CIMPLICITY SNP communications can connect with either a programming port or a port on the CMM communications module.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint

Triggered Reads Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics


Supported Devices GE Fanuc Series 90-70 PLCs GE Fanuc Series 90-30 PLCs GE Fanuc Series 90 Micro PLC

Supported Networks RS-232 RS-485


Read/Write: %AI, %AO, %I, %G, %M, %T, %Q, %R,

Read: %S, %SA, %SB, %SC



POWER SUPP LY

SERIES 90-70




GE NI US BUS


MABLE

INPUT 120 VAC

OUTPUT 120V AC,O5A

INPUT 120 VAC

INPUT 120 VAC

OUTPUT 120VAC,O5A

ENAB LE DRUNOK

USER 2USER 1OKPGMR

BUS

PROGRA M-

CONTROLLER

RS-422 Multi-dropPOWER SUPP LY

SERIES 90-70




GE NI US BUS


M ABLE

INPUT 120 VAC

OUTPUT 120V AC,O5A

INPUT 120 VAC

INPUT 120 VAC

OUTPUT 120VAC,O5A

ENAB LE DRUNOK

USER 2USER 1OKPGMR

BUS

PROG RA M-

CONTROLLER

POWER SUPPLY

SE RIES 90-70




GE NIUS BUS

CONTROL- LE R GE Fanuc

MABLE

INPUT 120 VAC

OUTPUT 120VAC,O5A

INPUT 120 VAC

INPUT 120 VAC

OUTPUT 120V AC,O5A

ENABLE DRUNOK

USER 2USER 1OKPGMR

BUS

PROGRAM-

CONTROLLER

FANUC Spares




Series 90™ TCP/IP Communications CIMPLICITY® Series 90™ TCP/IP Communications software provides high speed communications to GE Fanuc Series 90 PLCs via an Ethernet LAN. Series 90 Ethernet communications supports PLC redundancy, and when used with GE Fanuc HBR-30 and 780 redundancy products, failover to the active PLC is implemented without application programming.

GE Fanuc’s unique Ethernet Global Data routes information between 90-70 PLCs and CIMPLICITY HMI at maximum speeds with minimum overhead. TCP/IP communications are easy to configure and diagnostic programs give you immediate read/write access any Series 90 PLC on the LAN. The diagnostic programs can report the communications data rates to target PLCs.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data (Windows NT) ✓ Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit) ✓ Floating ✓ Text ✓ Arrays Series 90 is a trademark of GE Fanuc Automation North America, Inc

Supported Devices GE Fanuc Series 90-70 PLCs GE Fanuc Series 90-30 PLCs PLC Redundancy (on Windows NT for HBR-30 and Series 90 - 780 configurations)

Supported Networks Ethernet Cable Redundancy (on Windows NT via dual Ethernet cards)

Supported PLC Data Series 90-70:

Read/Write: %AI, %AQ, %I, %G, %M, %L, %T, %Q, %R,

Read: %S, %SA, %SB, %SC Series 90-30:

Read/Write: %AI, %AQ, %I, %G, %M, %L, %T, %Q, %R,

Read: %S, %SA, %SB, %SC


Required Hardware Series 90 Ethernet Interface: IC697CMM741 for Series 90-70 IC697CMM321 for Series 90-30

Sample Network

Computer

Single or Redundanct Ethernet Lan

Series 90

Hot Standby Series 90 PLCs



Sharp TCP/IP Communications CIMPLICITY® Sharp TCP/IP Communications software provides TCP/IP communications to Sharp JW Series PLCs with a JW-50CM interface over an Ethernet network. The TCP/IP connection provides fast communications over industry standard Ethernet networks, and HMI support for unsolicited updates from the PLC provides superior system response times while conserving system bandwidth. Interactive communications verification functions simply setup and debugging of communications.



Sample Network

Supported Devices JW-50CU JW-70CU JW-100CU

Required PLC Network Device Ethernet Interface Module type JW-50CM.

Supported PLC Data File 0 register (includes I/O relay, Auxiliary relay, Retentive relay, General purpose relay, TMR, CNT time limit contact, TMR, CNT, MD, and Register memory) File-1 register File-2 register File-3 register File-4 register File-5 register File-6 register File-7 register



FANUC Spares




Siemens TI Serial Communications CIMPLICITY® Siemens TI Serial Communications software provides point to point communications to Siemens TI model 5x5 PLCs over a serial RS-232 connection to the PLCs serial port.



Supported Devices Siemens TI 505 Series PLCs

Required PLC Network Device None.

Supported PLC Data Discrete input registers Discrete output registers Word input registers Word output registers Constant Memory Variable Memory Internal Control Relays Timers Current values Preset values



Computer

RS-232

Siemens TI545 PLC



Smarteye Communications CIMPLICITY® Smarteye Communications software provides communications to Smarteye Electronic Assemblies (SEA) over an RS-232 multi-drop serial link. Up to 32 SEA devices, each with up to 8 Smarteye readers, can be monitored on a single RS-232 link.

In addition to reading labels that pass by a reader, CIMPLICITY Smarteye Communications can monitor and report errors and diagnostic information. CIMPLICITY translates the numeric error codes to meaningful messages for display in screens and log files.

Smarteye Communications integrates seamlessly with the CIMPLICITY Tracker to simplify the development of product tracking and routing applications.

Supported Operations ✓ Polled Read at user defined rates ✓ Poll After Setpoint ✓ Triggered Reads ✓ Unsolicited Data (*) Analog Deadband ✓ Alarm on Communications Failure ✓ Host Redundancy Configurations ✓ Communication Statistics

Supported Data Types ✓ Signed Integer (8, 16, & 32-bit) ✓ Unsigned Integer (8, 16, & 32-bit)

Floating ✓ Text

Arrays (*) Unsolicited data is supported in RS-232 point-to-point configurations only.

Supported Devices Smarteye v096

Supported Networks RS-232 RS-422 Multi-drop

Supported Data Labels Errors Diagnostics System Data



Sample Network

Computer

RS-232 Multi-drop cable

SEA SEA

Readers(up to 8)

Readers(up to 8)

FANUC Spares




Square D SY/MAX Communications CIMPLICITY® Square D SY/MAX Communications software provides communications to SY/MAX PLCs over a Serial connection to the PLCs serial port or to the SY/NET Network Interface Module. Connections using an NRD powered communications cable are supported as are those using standard serial cables.


Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure

Server Redundancy Configurations ✓ Communication Statistics


Sample Network

Supported Devices

SY/MAX Model 600 Processor; Class 8020, Type SCP631, and 632

SY/MAX Model 500 Processor; Class 8020, Type SCP501, 522, 523, and 544

SY/MAX Model 400 Processor; Class 8020, Type SCP401, 423, 424, and 444

SY/Matic Weld Controllers (EQ5200, EQ5110, EQ5100)

Power Logic Circuit Monitor; Class 3020

Devices which adhere to the protocol specified in the Square D SY/MAX Protocol Reference Instruction Bulletin 30598-713-01.

Required PLC Network Device None. SY/NET Network Interface Module supported.

Supported PLC Data Registers


Required Computer Hardware None



Toyopuc Ethernet Communications CIMPLICITY® Toyopuuc Ethernet Communications software provides communications to Toyoda Toyopuc PC2 Series Programmable Controler over a standard Ethernet connection. Communications to PC2 controllers via a secondary ME-NET or High Speed PC Link (HPC) LAN is also supported


Unsolicited Data ✓ Analog Deadband ✓ Alarm on Communications Failure

Server Redundancy Configurations ✓ Communication Statistics


Sample Network

Supported Devices

Toyoda Toyopuc PC2 Series

Required PLC Network Device Ethernet EN-IF card (v2.1 or later)

Supported PLC Data Edge Relay Keep Relay Specific Relay Timer/Counter Link Relay I/O Relay Internal Relay Specific Register Timer/Counter Current Value Link Register Data Register File Register CPU Status

Required Software Hellowin or GL1 programming software for EN-IF setup


Ethernet Network

ToyopucPLC

ToyopucPLC

ME-NETor HPC

ToyopucPLC

FANUC Spares


Documents

FANUC Spares - University of Colorado Boulderucc.colorado.edu/fanuc/drivrlst.pdf · Page 7 of 49 CIMPLICITY HMI I/O Communications February 2001 GE Fanuc Automation North America,