FAMILY - L WINGNUTS AND T-HANDLESbotecoamerica.com/.../BotecoAmerica-L-Wingnuts-T-Handles.pdfL - WINGNUTS AND T-HANDLES T-HANDLE WITH THREADED STUD Material: Reinforced polyamide

FAMILY - LWINGNUTS AND

T-HANDLESUPDATE 2016 - INCH

L - 3BOTECO ® - © All right reserved - www.boteco.itAny unathorized reproduction is strictly forbidden

L270PA6+GF

UL94HB

+135°-25°

H

A

Bh1

c

dQ

d1

F Art. A B H h1 c d d1 2B Q q oz F1 (lb)L27050.TU1001 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 10/24 0,4724 0,4589 922

L27050.TU1/401 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1/4-20 0,3937 0,3883 922

L27050.TU5/1601 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 5/16-18 0,5512 0,4236 922

L27060.TU1001 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 10/24 0,4724 0,6707 1304

L27060.TU1/401 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1/4-20 0,3937 0,58245 1304

L27060.TU5/1601 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 5/16-18 0,5512 0,61775 1304

L27072.TU1/401 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 1/4-20 0,5906 0,8825 1461

L27072.TU5/1601 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 5/16-18 0,7874 0,9884 1461

L27072.TU3/801 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3/8-16 0,8268 1,059 1461

Presumable presence in the stock in %

( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916

L - WINGNUTS AND T-HANDLES

T-HANDLE WITH FEMALE THREADED INSERT

Material:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.

Colour:Black (RAL 9011).

Main Insert:Brass blind threaded bush (tolerance 2B).

SpEcIAL rEQUEST:

• It is possible to supply the inserts in different materials, on request and for quantities.

• It is possible to supply colours as shown in the table at pag. L-27, on request and for quantities.

+275°-13°

L - 4www.boteco.it - © All right reserved - BOTECO ®

Any unathorized reproduction is strictly forbidden

H

A

Bh1

c

d

Q

d1

L270 CINPA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H h1 c d d1 2B Q q oz F1 (lb)L27050.TU1001cIN 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 10/24 0,4724 0,4589 922

L27050.TU1/401cIN 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1/4-20 0,3937 0,3883 922

L27050.TU5/1601cIN 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 5/16-18 0,5512 0,4236 922

L27060.TU1001cIN 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 10/24 0,4724 0,6707 1304

L27060.TU1/401cIN 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1/4-20 0,3937 0,58245 1304

L27060.TU5/1601cIN 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 5/16-18 0,5512 0,61775 1304

L27072.TU1/401cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 1/4-20 0,5906 0,8825 1461

L27072.TU5/1601cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 5/16-18 0,7874 0,9884 1461

L27072.TU3/801cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3/8-16 0,8268 1,059 1461

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

T-HANDLE WITH FEMALE stainless steel THREADED INSERT


Surface:Satin.


Main Insert:Stainless steel blind threaded bush (AISI 303).(tolerance 2B).

SpEcIAL rEQUEST:



L271PA6+GF

UL94HB

+135°-25°

HQ

d1d

A

Bh1

c

F Art. A B H h1 c d LM d1 2A Q q oz F1 (lb)L27150.TN10/32X..01 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1,1811 10/32 1/2 - 3/4 0,42-0,46 922

L27150.TU1/4X..01 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1,1811 1/4-20 1/2 - 1 0,48-0,54 922

L27160.TU1/4X..01 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1,1811 1/4-20 1/2 - 3/4 - 1 0,69-0,79-,85 1304

L27160.TU5/16X..01 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1,1811 5/16-18 1/2 - 1 0,85-1,04 1304

L27172.TU5/16X..01 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 5/16-18 1 - 1 1/4 1,43-1,5 1461

L27172.TU3/8X..01 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 3/8-16 1 - 1,37 - 2 1/2 1,88-2,06-2,58 1461

L27172.TU1/2X3801 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 1/2-13 1 1/2 2,23 1461


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


T-HANDLE WITH THREADED STUD


Surface:Satin.


Main Insert:Zinc plated steel threaded stud (tolerance 2A).

SpEcIAL rEQUESTS:

• It is possible to supply inserts in different lenghts or by special design, on request and for quantities.

• It is possible to supply inserts in different materials, on request and for quantities.

• It is possible to supply colours as shown in the table on page L-27, on request and for quantities.

LM = Maximum mouldable length.

Enter the stud length choice in the two .. of the article code. Lengths by request with 250 pieces minimum quantity.

+275°-13°



HQ

d1d

A

Bh1

c

L271 CINPA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H h1 c d LM d1 2A Q q oz F1 (lb)L27150.TN10/32X..01cIN 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1,1811 10/32 A.R. - 922

L27150.TU1/4X..01cIN 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1,1811 1/4-20 A.R. - 922

L27160.TU1/4X..01cIN 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1,1811 1/4-20 A.R. - 1304

L27160.TU5/16X..01cIN 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1,1811 5/16-18 A.R. - 1304

L27172.TU5/16X..01cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 5/16-18 A.R. - 1461

L27172.TU3/8X..01cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 3/8-16 A.R. - 1461

L27172.TU1/2X..01cIN 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3,1496 1/2-13 A.R. - 1461

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

T-HANDLE WITH THREADED STAINLESS STEEL STUD


Surface:Satin.


Main Insert:Stainless steel threaded stud (AISI 303).(tolerance 2A).

SpEcIAL rEQUESTS:





A.r. = by request.


L272PA6+GF

UL94HB

+135°-25°

H

A

Bh1

c

d

Q

d1

F Art. A B H h1 c d d1 Q q oz F1 (lb)L27250.TU1/401 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1/4-20 0,7874 0,28 629

L27260.TU1/401 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1/4-20 0,7480 0,49 674

L27260.TU5/1601 2,3622 0,7087 1,2992 0,9449 0,2362 0,6693 5/16-18 0,7480 0,49 674

L27260.TU3/801 2,3622 0,7087 1,2992 0,9449 0,2362 0,7087 3/8-16 0,7480 0,46 674

L27272.TU5/1601 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 5/16-18 0,8268 0,71 1034

L27272.TU3/801 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 3/8-16 0,8268 0,71 1034


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


T-HANDLE WITH PLASTIC THREADED HOLE


Surface:Satin.


Hole:Female threaded blind hole obtained by moulding the plastic. (tolerance in not applicable).

SpEcIAL rEQUEST:


+275°-13°



H

A

Bh1

c

d

Q

d1

L273PA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H h1 c d d1 H9 Q q oz F1 (lb)L27350.TD1/401cON 1,9685 0,5906 0,9449 0,6693 0,1969 0,5512 1/4 0,6299 0,42 922

L27360.TD1/401cON 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 1/4 0,6299 0,67 1304

L27360.TD5/1601cON 2,3622 0,7087 1,2992 0,9449 0,2362 0,6496 5/16 0,5906 0,74 1304

L27372.TD5/1601cON 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 5/16 0,5906 0,99 1461

L27372.TD3/801 2,8346 0,7480 1,3386 0,7874 0,3937 0,7087 (*) 3/8 0,6693 1,06 1461

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

T-HANDLE WITH SMOOTH HOLE INSERT


Surface:Satin.


Main Insert:Brass smooth blind bored bush (tolerance bore H7) ATTENTION: the bore cannot be enlarged.

(*) ZInc plated steel blind bored bush (tolerance bore H10).

SpEcIAL rEQUESTS:

• It is possible to supply the inserts with different materials, on request and for quatities.


GALLETTI “euromodel”



A

B

d

H

mc

d1

Q

d3

l803-L803PINPA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H m c d d3 d1 2B Q q ozL80344.TU100113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 10-24 0,5906 0,35

L80344.TU1/40113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4-20 0,5906 0,35

L80344.TU5/160113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 5/16-18 0,5906 0,39

L80352.TU100113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 10-24 0,7087 0,53

L80352.TU1/40113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 1/4-20 0,7087 0,53

L80352.TU5/160113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16-18 0,7087 0,56

L80352.TU3/80113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 3/8-16 0,7087 0,56

L80367.TU1/40113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 1/4-20 0,7087 0,92

L80367.TU5/160113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 5/16-18 0,7087 0,92

L80367.TU3/80113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8-16 0,7087 0,95

L80367.TU1/20113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 1/2-13 0,7087 0,95

F Art. A B H m c d d3 d1 2B Q q ozL80344.TU1/40113pIN 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4-20 0,5906 0,35

L80352.TU5/160113pIN 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16-18 0,7087 0,56

L80367.TU3/80113pIN 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8-16 0,7087 0,95

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )

“euromodel” wingnut with threaded through insert


Material:Reinforced polyamide. Oils and greases resistant.

Surface:Satin.


Central Cap:Grey PA6 (RAL 7035 cod. 13). Alternative Cap Colour:Orange (RAL 2004 cod. 02).Blue (RAL 5015 cod. 07).Yellow (RAL 1021 cod. 10).Red (RAL 3000 cod. 16).Green (RAL 6024 cod. 17).Black (RAL 9011 cod. 01).

Main Insert:L803: Brass right through threaded bush. ( 2B tolerance ) L803PIN: Stainless steel (AISI 303) right through threaded bush. ( 2B tolerance )

SpEcIAL rEQUESTS:• It is possible to supply the inserts in different materials, on request and for quantities.

• It is possible to supply the wingnuts with colours as shown in the table at page L-27 on request and for quantities.

PROTECTEDMODEL

Version L803: Standard brass insert

Version L803 PIN: Stainless steel insert


PA6+GF

UL94HB

+135°-20°

l806-l806pin

A

B

d

mc

d1

Q

d3

H

F Art. A B H m c d d3 d1 2B Q q ozL80644.TU1/401pIN 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 1/4-20 0,5906 0,32

L80652.TU5/1601pIN 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 5/16-18 0,7087 0,56

L80667.TU3/801pIN 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 3/8-16 0,7087 0,92

F Art. A B H m c d d3 d1 2B Q q ozL80644.TU1001 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 10-24 0,5906 0,32

L80644.TU1/401 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 1/4-20 0,5906 0,32

L80644.TU5/1601 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 5/16-18 0,5906 0,35

L80652.TU1001 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 10-24 0,7087 0,49

L80652.TU1/401 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 1/4-20 0,7087 0,53

L80652.TU5/1601 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 5/16-18 0,7087 0,56

L80652.TU3/801 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 3/8-16 0,7087 0,56

L80667.TU1/401 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 1/4-20 0,7087 0,88

L80667.TU5/1601 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 5/16-18 0,7087 0,88

L80667.TU3/801 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 3/8-16 0,7087 0,92

L80667.TU1/201 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 1/2-13 0,7087 0,92


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


“euromodel” wingnut with threaded through insert

without capMaterial:Reinforced polyamide. Oils and greases resistant.

Surface:Satin.


Main Insert:L806: Brass right through threaded bush. ( 2B tolerance )L806PIN: Stainless steel (AISI 303) right through threaded bush.( 2B tolerance )

SpEcIAL rEQUESTS:• It is possible to supply the inserts in different materials, on request and for quantities.

• It is possible to supply the wingnuts with colours as shown in the table at page L-27, on request and for quantities.



PROTECTEDMODEL

+275°-13°



PA6+GF

UL94HB

+135°-25°

l804-l804Cin

A

B

H

mc

d3

Q

d1d

+275°-13°

F Art. A B H m c d d3 d1 2A Q q ozL80444.TU10X..0113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 10-24 1/2 - 3/4 0,32-0,36

L80444.TU1/4X..0113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4-20 1/2 - 3/4 - 1 0,37-0,41-0,46

L80444.TU5/16X..0113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 5/16-18 1/2 - 3/4 - 1 0,58-0,67-0,74

L80452.TU1/4X..0113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 1/4-20 1/2 - 3/4 - 1 0,55-0,59-0,63

L80452.TU5/16X..0113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16-18 1/2 - 3/4 - 1 0,75-0,84-0,92

L80452.TU3/8X..0113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 3/8-16 3/4 - 1 1,07-1,20

L80467.TU1/4X..0113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 1/4-20 1/2 - 3/4 - 1 0,81-0,88-0,95

L80467.TU5/16X..0113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 5/16-18 1/2 - 3/4 - 1 1,08-1,13-1,20

L80467.TU3/8X..0113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8-16 3/4 - 1 1,34-1,45

L80467.TU1/2X..0113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 1/2-13 1 - 1 1/2 1,70-2,0

F Art. A B H m c d d3 d1 2A Q q ozL80444.TU1/4X..0113cIN 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4-20 A.R. -

L80452.TU5/16X..0113cIN 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16-18 A.R. -

L80467.TU3/8X..0113cIN 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8-16 A.R. -

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )

“euromodel” wingnut with threaded stud


Surface:Satin.



Main Insert:L804: Zinc plated steel threaded stud. (tolerance 2A)L804CIN: Stainless steel (AISI 303) threaded stud. (tolerance 2A)

Maximum mouldable length (LM):L804-44: 80 mmL804-52: 80 mmL804-67: 100 mm

SpEcIAL rEQUESTS:• It is possible to supply the inserts with different lengths, on request and for quantities.




Version L804: Zinc plated steel threaded stud

Version L804 CIN: Stainless steel threaded stud

PROTECTEDMODEL



A.r. = by request.



PA6+GF

UL94HB

+135°-25°

l807-l807Cin

A

Bm

c

Q

d1d

d3

H

F Art. A B H m c d d3 d1 2A Q q ozL80744.TU1/4X..01cIN 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4-20 A.R. -

L80752.TU5/16X..01cIN 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16-18 A.R. -

L80767.TU3/8X..01cIN 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8-16 A.R. -

F Art. A B H m c d d3 d1 2A Q q ozL80744.TU10X..01 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 10-24 1/2 - 3/4 0,29-0,33

L80744.TU1/4X..01 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 1/4-20 1/2 - 3/4 - 1 0,34-0,38-0,43

L80744.TU5/16X..01 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 5/16-18 1/2 - 3/4 - 1 0,55-0,64-0,71

L80752.TU1/4X..01 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 1/4-20 1/2 - 3/4 - 1 0,51-0,56-0,60

L80752.TU5/16X..01 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 5/16-18 1/2 - 3/4 - 1 0,72-0,81-0,89

L80752.TU3/8X..01 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 3/8-16 3/4 - 1 1,04-1,17

L80767.TU1/4X..01 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 1/4-20 1/2 - 3/4 - 1 0,78-0,85-0,92

L80767.TU5/16X..01 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 5/16-18 1/2 - 3/4 - 1 1,05-1,10-1,17

L80767.TU3/8X..01 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 3/8-16 3/4 - 1 1,31-1,42

L80767.TU1/2X..01 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 1/2-13 1 - 1 1/2 1,67-1,97


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916

“euromodel” wingnut with threaded stud without cap



Surface:Satin.


Main Insert:L807: Zinc plated steel threaded stud. (tolerance 2A)L807CIN: Stainless steel (AISI 303) threaded stud. (tolerance 2A)

Maximum mouldable length (LM):L807-44: 80 mmL807-52: 80 mmL807-67: 100 mm

SpEcIAL rEQUESTS:• It is possible to supply the inserts with different lengths, on request and for quantities.



Version L807: Zinc plated steel threaded stud

Version L807 CIN: Stainless steel threaded stud

PROTECTEDMODEL




A.r. = by request.

+275°-13°



PA6+GF

UL94HB

+135°-25°

l805-l805pin

A

B

d

H

mc

Q

d3

d1

+275°-13°

F Art. A B H m c d d3 d1 H9 Q oz

L80544.TD1/40113pIN 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4 0,5906 0,32

L80552.TD5/160113pIN 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16 0,7087 0,53

L80567.TD3/80113pIN 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8 0,7087 0,92

F Art. A B H m c d d3 d1 H9 Q q ozL80544.TD1/40113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 1/4 0,5906 0,32

L80544.TD5/160113 1,7323 0,6299 0,8661 0,3150 0,5512 0,5512 0,3937 5/16 0,5906 0,35

L80552.TD1/40113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 1/4 0,7087 0,49

L80552.TD5/160113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 5/16 0,7087 0,53

L80552.TD3/80113 2,0472 0,7480 1,0236 0,3740 0,6496 0,6693 0,5118 3/8 0,7087 0,56

L80567.TD1/40113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 1/4 0,7087 0,88

L80567.TD5/160113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 5/16 0,7087 0,88

L80567.TD3/80113 2,6378 0,9449 1,2795 0,4331 0,8465 0,8268 0,6299 3/8 0,7087 0,92

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

“euromodel” wingnut with smooth hole insert


Surface:Satin.



Main Insert:L805: Brass right through bored bush with H9 tolerance.L805CIN: Stainless steel (AISI 303) right through bored bush with H9 tolerance.





PROTECTEDMODEL

A.r. = Only by request.


l808-l808pinPA6+GF

UL94HB

+135°-25°

A

B

dm

c

Q

d3

H

d1

F Art. A B H m c d d3 d1 H9 Q q ozL80844.TD1/401 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 1/4 0,5906 0,28

L80844.TD5/1601 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 5/16 0,5906 0,32

L80852.TD1/401 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 1/4 0,7087 0,46

L80852.TD5/1601 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 5/16 0,7087 0,49

L80852.TD3/801 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 3/8 0,7087 0,53

L80867.TD1/401 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 1/4 0,7087 0,85

L80867.TD5/1601 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 5/16 0,7087 0,85

L80867.TD3/801 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 3/8 0,7087 0,88

F Art. A B H m c d d3 d1 H9 Q q ozL80844.TD1/401pIN 1,7323 0,6299 0,8465 0,3150 0,5512 0,5512 0,3937 1/4 0,5906 0,28

L80852.TD5/1601pIN 2,0472 0,7480 1,0039 0,3740 0,6496 0,6693 0,5118 5/16 0,7087 0,49

L80867.TD3/801pIN 2,6378 0,9449 1,2598 0,4331 0,8465 0,8268 0,6299 3/8 0,7087 0,88


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


“euromodel” wingnut with smooth hole insert

without capMaterial:Reinforced polyamide. Oils and greases resistant.

Surface:Satin.


Main Insert:L808: Brass right through bored bush with H9 tolerance.L808CIN: Stainless steel (AISI 303) right through bored bush with H9 tolerance.





PROTECTEDMODEL



+275°-13°


Any unathorized reproduction is strictly forbidden ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

STANDARDWINGNUTS


L750PA6+GF

UL94HB

+135°-25°

d

Q

d1

B

A

H m

F Art. A B H m d d1 2B Q q ozL75032.TN10/3201 1,2992 0,5906 0,6496 0,0394 0,4724 10/32 0,2756 0,25

L75032.TU1/401 1,2992 0,5906 0,6496 0,0394 0,4724 1/4-20 0,2756 0,21

L75032.TU5/1601 1,2992 0,5906 0,6496 0,0394 0,4724 5/16-18 0,2756 0,21

L75048.TU1/401 1,8898 0,5906 0,6299 0,0394 0,4921 1/4-20 0,2756 0,35

L75048.TU5/1601 1,8898 0,5906 0,6299 0,0394 0,4921 5/16-18 0,2756 0,35


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


WINGNUT WITH FEMALE THREADED INSERT


Surface:Satin.



SpEcIAL rEQUEST:



+275°-13°



d

Q

d1

B

A

H m

L750 CINPA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H m d d1 2B Q q ozL75032.TN10/3201cIN 1,2992 0,5906 0,6496 0,0394 0,4724 10/32 0,2756 0,32

L75032.TU1/401cIN 1,2992 0,5906 0,6496 0,0394 0,4724 1/4-20 0,2756 0,28

L75032.TU5/1601cIN 1,2992 0,5906 0,6496 0,0394 0,4724 5/16-18 0,2756 0,28

L75048.TU5/1601cIN 1,8898 0,5906 0,6299 0,0394 0,4921 5/16-18 0,2756 0,28

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

WINGNUT WITH STAINLESS STEELFEMALE THREADED INSERT


Surface:Satin.


Main Insert:Stainless steel blind threaded bush (AISI 303).(tolerance 2B).

SpEcIAL rEQUEST:



L751PA6+GF

UL94HB

+135°-25°

B

A

HL

m

d1d

+275°-13°

F Art. A B H m d LM d1 2A Q q ozL75132.TN10/32X..01 1,2992 0,5906 0,6496 0,0394 0,4724 2,3622 10/32 1/2 - 3/4 - 1 0,26 - 0,28 - 0,32

L75132.TU1/4X..01 1,2992 0,5906 0,6496 0,0394 0,4724 2,3622 1/4-20 1/2 - 3/4 - 1 - 1 1/4 0,35-0,40-0,42-0,46

L75132.TU5/16X..01 1,2992 0,5906 0,6496 0,0394 0,4724 2,3622 5/16-18 0,63- 3/4 - 1 - 1 3/4 - 2 0,51-0,55-0,62-0,64-0,88

L75148.TU1/4X..01 1,8898 0,5906 0,6299 0,0394 0,4921 2,7559 1/4-20 1/2 - 3/4 - 1 0,49-0,59-0,63

L75148.TU5/16X..01 1,8898 0,5906 0,6299 0,0394 0,4921 2,7559 5/16-18 3/4 - 1 0,69-0,76


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


WINGNUT WITH THREADED STUD


Surface:Satin.



SpEcIAL rEQUESTS:








B

A

HL

md1d

L751 CINPA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H m d LM d1 2A Q q oz

L L75132.TU1/4X1301cIN 1,2992 0,5906 0,6496 0,0394 0,4724 2,3622 1/4-20 1/2 0,46

L L75132.TU5/16X..01cIN 1,2992 0,5906 0,6496 0,0394 0,4724 2,3622 5/16-18 A.R. -

L L75148.TU1/4X..01cIN 1,8898 0,5906 0,6299 0,0394 0,4921 2,7559 1/4-20 A.R. -

L L75148.TU5/16X..01cIN 1,8898 0,5906 0,6299 0,0394 0,4921 2,7559 5/16-18 A.R. -

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

WINGNUT WITH STAINLESS STEEL THREADED STUD


Surface:Satin.


Main Insert:Stainless steel threaded stud (AISI 303).(tolerance 2A).

SpEcIAL rEQUESTS:





A.r. = by request.


L754PA6+GF

UL94HB

+135°-25°

B

A

H

Q

d1

+275°-13°

F Art. A B H d1 2A Q q ozL75448.TU1/401 1,7717 0,7874 0,6693 1/4-20 0,2756 0,39

L75448.TU5/1601 1,7717 0,7874 0,6693 5/16-18 0,2756 0,39


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


LARGE WINGNUT WITH FEMALE THREADED INSERT


Surface:Satin.



SpEcIAL rEQUEST:





B

A

H

d3

d2

d1

L755PA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H d2 d3 d1 2A q ozL75548.TU1/401 1,7717 0,7874 0,6693 0,3740 0,3937 1/4-20 0,60

L75548.TU5/1601 1,7717 0,7874 0,6693 0,3740 0,3937 5/16-18 0,56

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

LARGE WINGNUT WITH FEMALERIGHT THROUGH THREADED INSERT


Surface:Satin.


Main Insert:Zinc palted steel right through nut (tolerance 2B).

SpEcIAL rEQUEST:




L756PA6+GF

UL94HB

+135°-25°

HQ

d1

B

A

+275°-13°

F Art. A B H LM d1 2A Q q ozL75648.TU1/4X..01 1,7717 0,7874 0,6693 1,9685 1/4-20 1/2 - 3/4 - 1 1/4 0,5 - 0,54 - 0,58

L75648.TU5/16X1901 1,7717 0,7874 0,6693 1,9685 5/16-18 3/4 0,71


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


LARGE WINGNUT WITH THREADED STUD


Surface:Satin.



SpEcIAL rEQUESTS:





Enter the stud length choice in the two .. of the article code. Lengths by request with 150- pieces minimum quantity.



A

B

H

d

cm

d3

h3

d1

Q

L747PA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H m c d d3 h3 d1 2B Q q ozL74728.TN10/3201 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 10/32 0,3150 0,18

L74728.TU1/401 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 1/4-20 0,3150 0,21

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

28MM. WINGNUT WITH FEMALE THREADED INSERT


Surface:Satin.



SpEcIAL rEQUEST:




L748PA6+GF

UL94HB

+135°-25°

cm

d1

A

B

d

H

d3

h3Q

+275°-13°

F Art. A B H m c d d3 h3 d1 2B Q q ozL74828.TN10/3201 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 10/32 0,4921 0,18

L74828.TU1/401 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 1/4-20 0,4921 0,21


( F ) 90%( J ) 40%( K ) 5%( L )

ver. LUS.01-0916


28MM. WINGNUT WITH FEMALERIGHT THROUGH THREADED INSERT


Surface:Satin.


Main Insert:Brass right through threaded bush (tolerance 2B).

SpEcIAL rEQUEST:





Cm

d1

Q

d

H

d3

h3

B

A

L749PA6+GF

UL94HB

+135°-20°

+275°-13°

F Art. A B H m c d d3 h3 LM d1 2A Q q ozL74928.TN10/32X..01 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 2,9528 10/32 A.R. -

L74928.TU1/4X..01 1,1024 0,5118 0,5118 0,1181 0,3937 0,4331 0,3150 0,0197 2,9528 1/4-20 A.R. -

ver. LUS.01-0916


( F ) 90%( J ) 40%( K ) 5%( L )L - WINGNUTS

AND T-HANDLES

28MM. WINGNUT WITH THREADED STUD


Surface:Satin.



SpEcIAL rEQUESTS:






A.r. = By request.


9011

2004

2011

9010

5002

5005

5015

5018

5019

5010

1007

1021

7024

7035

3000

6024

01

02

03

04

05

06

07

19

21

22

09

10

12

13

16

17

RAL Cod.

-

-

Pant. 645 U

Pant. 300

-

-

NCS 7500

-

-

-

-

-

-

-

52

53

54

55

57

59

60

64

65

66

70

71

72

73

Ref. Cod.

Black

Orange

Orange

White

Blue

Blue

Blue

Blue

Blue

Blue

Yellow

Yellow

Grey

Grey

Red

Green

Colour

RAL COLOURS CODING

White

Blue

Blue

Blue

Grey

Grey

Grey

Red

Red

Natural

Green

Brown

Cream

Violet

Colour

OTHER COLOURS

Colour Chart


Ph

: D

VR

FO

TO

GR

AF

IA -

Mar

ano

Vic

. ;

Gra

ph

ics

and

Pri

nti

ng

: J.

Pie

trib

iasi

-M.

Bo

rgo

- B

ote

co ®

; © A

ll ri

gh

ts r

eser

ved

An

y u

nat

ho

rize

d r

epro

du

ctio

n is

str

ictl

y fo

rbid

den

E-CATALOGUE

BOTECO Srlwww.boteco.it

36010 ZANE’ (VI) - ITALY

Via L. Pettinà 16 ( side street of Via Cuso)

Switchboard Tel.:+39-0445-316411 - Fax:+39-0445-316400

Sales Fax:+39-0445-316401 mail: [email protected]

Administration Fax:+39-0445-316402 mail: [email protected]

Technical Fax:+39-0445-316404 mail: [email protected]

Certified Mail Box: [email protected]

AUTHORISED RESELLER

ver. LUS.01-0916

Documents

FAMILY - L WINGNUTS AND T-HANDLESbotecoamerica.com/.../BotecoAmerica-L-Wingnuts-T-Handles.pdfL - WINGNUTS AND T-HANDLES T-HANDLE WITH THREADED STUD Material: Reinforced polyamide