FAMILy - F solid locking handwheels - Boteco America · 2016. 11. 14. · F110 F Art. D d H m c d1 2B Q q oz F110022.TN10/3201 0,866 0,472 0,689 0,433 0,256 10/32 0,315 0,194

update 2016 - INCH

FAMILY - fCONTROL HANDWHE-EL WITH INDICATOR

FAMILy - Fsolid locking handwheels

F - 3BOTECO ® - © All right reserved - www.boteco.itAny unathorized reproduction is strictly forbidden

Q

d1d

cm

HD

PA6+GF

UL94HB

+135°-20°

F110

F Art. D d H m c d1 2B Q q ozF110022.TN10/3201 0,866 0,472 0,689 0,433 0,256 10/32 0,315 0,194

F110027.TN10/3201 1,063 0,551 0,866 0,512 0,354 10/32 0,394 0,318

F110027.TU1/401 1,063 0,551 0,866 0,512 0,354 1/4-20 0,394 0,335

F110033.TU5/1601 1,299 0,748 1,024 0,591 0,433 5/16-18 0,512 0,565

F110033.TU3/801 1,299 0,748 1,024 0,591 0,433 3/8-16 0,512 0,600

Presumable presence in the stock in %

( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

Material:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.

Colour:Black (RAL 9011).

Main Insert:Brass blind threaded bush (tolerance 2B).

SpeciAl reQUeST:

• It is possible to supply the inserts in different materials, on request and for quantities.

• It is possible to supply colours as shown in the table at pag. F-35, on request and for quantities.

SOLID 6 LOBE KNOB WITH FEMALE THREADED INSERT

F - SOliD lOcKiNG KNOBS

+275°-13°

F - 4www.boteco.it - © All right reserved - BOTECO ®

Any unathorized reproduction is strictly forbidden

PA6+GF

UL94HB

+135°-20°

F111

d1

cm

HD

Q

d

F Art. D d H m c d1 2A Q lM q ozF111022.TN10/32X..01 0,866 0,472 0,689 0,433 0,256 10/32 A.R. 1,969 -

F111027.TN10/32X..01 1,063 0,551 0,866 0,512 0,354 10/32 A.R. 2,362 -

F111027.TU1/4X..01 1,063 0,551 0,866 0,512 0,354 1/4-20 A.R. 2,362 -

F111033.TU5/16X..01 1,299 0,748 1,024 0,591 0,433 5/16-18 A.R. 2,756 -

F111033.TU3/8X..01 1,299 0,748 1,024 0,591 0,433 3/8-16 A.R. 2,756 -


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 6 LOBE KNOB WITH MALE THREADED STUD


Surface:Satin.


Main Insert:Zinc plated steel threaded stud (tolerance 2A).

SpeciAl reQUeSTS:

• It is possible to supply inserts in different lengths or by special design, on request and for quantities.

• It is possible to supply inserts in different materials, on request and for quantities.

• It is possible to supply colours as shown in the table on page F-35, on request and for quantities.

lM = Maximum mouldable length.

Enter the stud length choice in the two .. of the article code. Lengths by request with 250 pieces minimum quantity.

A.r. = By request

+275°-13°


PA6+GF

UL94HB

+135°-20°

f175

D

H

cm

d d1

d3

h3Q

F Art. D H d c m d3 h3 d1 2B Q q ozF17530.TU10/2401 1,181 0,866 0,591 0,433 0,433 0,354 0,059 10/24 0,551 0,41F17530.TU1/401 1,181 0,866 0,591 0,433 0,433 0,354 0,059 1/4-20 0,394 0,42F17530.TU5/1601 1,181 0,866 0,591 0,433 0,433 0,354 0,059 5/16-18 0,551 0,48F17530.TU3/801 1,181 0,866 0,591 0,433 0,433 0,354 0,059 3/8-16 0,551 0,49F17540.TU1/401 1,575 0,965 0,669 0,472 0,492 0,472 0,039 1/4-20 0,630 0,78F17540.TU5/1601 1,575 0,965 0,669 0,472 0,492 0,472 0,039 5/16-18 0,551 0,76F17540.TU3/801 1,575 0,965 0,669 0,472 0,492 0,472 0,039 3/8-16 0,551 0,74F17550.TU5/1601 1,969 1,142 0,787 0,551 0,591 0,571 0,059 5/16-18 0,551 1,27F17550.TU3/801 1,969 1,142 0,787 0,551 0,591 0,571 0,059 3/8-16 0,551 1,31F17550.TU1/201 1,969 1,142 0,787 0,551 0,591 0,571 0,059 1/2-13 0,709 1,38F17560.TU5/1601 2,362 1,339 0,945 0,630 0,709 0,709 0,059 5/16-18 0,748 2,08F17560.TU3/801 2,362 1,339 0,945 0,630 0,709 0,709 0,059 3/8-16 0,827 2,08F17560.TU1/201 2,362 1,339 0,945 0,630 0,709 0,709 0,059 1/2-13 0,709 2,19


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID 6 LOBE HANDWHEEL WITH FEMALE THREADED INSERT


Surface:Satin.



SpeciAl reQUeST:




+275°-13°



PA6+GF

UL94HB

+135°-20°

f175 cin

D

H

cm

d d1

d3

h3Q

F Art. D H d c m d3 h3 d1 2B Q q ozF17530.TU1/401ciN 1,181 0,866 0,591 0,433 0,433 0,354 0,059 1/4-20 0,394 0,42

F17530.TU5/1601ciN 1,181 0,866 0,591 0,433 0,433 0,354 0,059 5/16-18 0,551 0,48

F17540.TU1/401ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,039 1/4-20 0,630 0,78

F17540.TU5/1601ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,039 5/16-18 0,551 0,76

F17540.TU3/801ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,039 3/8-16 0,551 0,74

F17550.TU5/1601ciN 1,969 1,142 0,787 0,551 0,591 0,571 0,059 5/16-18 0,551 1,27

F17550.TU3/801ciN 1,969 1,142 0,787 0,551 0,591 0,571 0,059 3/8-16 0,551 1,31

F17550.TU1/201ciN 1,969 1,142 0,787 0,551 0,591 0,571 0,059 1/2-13 0,709 1,38

F17560.TU5/1601ciN 2,362 1,339 0,945 0,630 0,709 0,709 0,059 5/16-18 0,748 2,08

F17560.TU3/801ciN 2,362 1,339 0,945 0,630 0,709 0,709 0,059 3/8-16 0,827 2,08

F17560.TU1/201ciN 2,362 1,339 0,945 0,630 0,709 0,709 0,059 1/2-13 0,709 2,19


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID 6 LOBE HANDWHEEL WITH FEMALE STAINLESS STEEL

THREADED INSERT



Surface:Satin.


Main Insert:Stainless steel blind threaded bush (AISI 303) (tolerance 2B).

SpeciAl reQUeST:


+275°-13°


PA6+GF

UL94HB

+135°-20°

f176

D

H

cm

d

d3

h3d1

Q

F Art. D H d c m d3 h3 d1 H7 Q q ozF17630.TD1/401 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 1/4 0,5906 0,60

F17630.TD5/1601 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 5/16 0,5906 0,67

F17640.TD1/401 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 1/4 0,5906 0,85

F17640.TD5/1601 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5/16 0,5906 0,92

F17640.TD3/801 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3/8 0,6693 0,99

F17650.TD1/401 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 1/4 0,5906 1,38

F17650.TD5/1601 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5/16 0,5906 1,45

F17650.TD3/801 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3/8 0,6693 1,48

F17660.TD5/1601 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 (*) 5/16 0,7087 2,75

F17660.TD3/801 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 (*) 3/8 0,9843 2,58

F17660.TD1/201 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 (*) 1/2 0,8661 2,65


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 6 LOBE HANDWHEEL WITH SMOOTH BORED INSERT


Surface:Satin.


Main Insert:Brass insert with smooth blind hole (tolerance H7).

(*) Zinc plated steel insert with smooth blind hole (tolerance H10).ATTENTION: bore cannot be enlarged.

SpeciAl reQUeST:



+275°-13°



PA6+GF

UL94HB

+135°-20°

f177

D

H

cm

d d1

d3

h3Q

F Art. D H d c m d3 h3 d1 2B Q q ozF17730.TU10/2401 1,181 0,866 0,591 0,433 0,433 0,433 0,157 10/24 0,709 0,42F17730.TU1/401 1,181 0,866 0,591 0,433 0,433 0,433 0,157 1/4-20 0,709 0,46F17730.TU5/1601 1,181 0,866 0,591 0,433 0,433 0,433 0,157 5/16-18 0,709 0,46F17740.TU1/401 1,575 0,965 0,669 0,472 0,492 0,472 0,236 1/4-20 0,709 0,71F17740.TU5/1601 1,575 0,965 0,669 0,472 0,492 0,472 0,236 5/16-18 0,709 0,74F17740.TU3/801 1,575 0,965 0,669 0,472 0,492 0,472 0,236 3/8-16 0,709 0,78F17750.TU5/1601 1,969 1,142 0,787 0,551 0,591 0,551 0,433 5/16-18 0,709 1,20F17750.TU3/801 1,969 1,142 0,787 0,551 0,591 0,551 0,433 3/8-16 0,709 1,24F17760.TU3/801 2,362 1,339 0,945 0,630 0,709 0,591 0,630 3/8-16 0,709 1,91F17760.TU1/201 2,362 1,339 0,945 0,630 0,709 0,591 0,630 1/2-13 0,709 1,94


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID 6 LOBE HANDWHEEL WITH RIGHT THROUGH FEMALE

THREADED INSERT



Surface:Satin.


Main Insert:Brass right through threaded bush (tolerance 2B).

SpeciAl reQUeST:



+275°-13°


PA6+GF

UL94HB

+135°-20°

f177 cin

D

H

cm

d d1

d3

h3Q

F Art. D H d c m d3 h3 d1 2B Q q ozF17730.TU10/2401ciN 1,181 0,866 0,591 0,433 0,433 0,433 0,157 10/24 0,709 0,42F17730.TU1/401ciN 1,181 0,866 0,591 0,433 0,433 0,433 0,157 1/4-20 0,709 0,46F17730.TU5/1601ciN 1,181 0,866 0,591 0,433 0,433 0,433 0,157 5/16-18 0,709 0,46F17740.TU1/401ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,236 1/4-20 0,709 0,71F17740.TU5/1601ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,236 5/16-18 0,709 0,74F17740.TU3/801ciN 1,575 0,965 0,669 0,472 0,492 0,472 0,236 3/8-16 0,709 0,78F17750.TU5/1601ciN 1,969 1,142 0,787 0,551 0,591 0,551 0,433 5/16-18 0,709 1,20F17750.TU3/801ciN 1,969 1,142 0,787 0,551 0,591 0,551 0,433 3/8-16 0,709 1,24F17760.TU3/801ciN 2,362 1,339 0,945 0,630 0,709 0,591 0,630 3/8-16 0,709 1,91F17760.TU1/201ciN 2,362 1,339 0,945 0,630 0,709 0,591 0,630 1/2-13 0,709 1,94


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 6 LOBE HANDWHEEL WITH RIGHT THROUGH FEMALE THREADED

STAINLESS STEEL INSERTMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Main Insert:Stainless steel right through threaded bush (AISI 303) (tolerance 2B).

SpeciAl reQUeST:


+275°-13°



PA6+GF

UL94HB

+135°-20°

f178

D

h3

d3

d

mc

HQ

d1

F Art. D H d c m d3 h3 lM d1 2A Q q ozF17830.TU10/24X..01 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 10/24 1/2 - 3/4 0,46-0,52

F17830.TU1/4X..01 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 1/4-20 1/2 - 3/4 - 1 0,53-0,58-0,62

F17830.TU5/16X..01 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 5/16-18 1/2 - 3/4 - 1 0,65-0,71-0,81

F17830.TU3/8X1901 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 3/8-16 3/4 0,97

F17840.TU1/4X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 1/4-20 1/2-3/4-1-1 1/40,85-0,88-0,92-

0,96

F17840.TU5/16X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 5/16-183/4-1-1 1/4- 1

1/21,05-1,11-1,18-

1,25

F17840.TU3/8X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 3/8-16 3/4-1-1 1/4 1,28-1,38-1,45

F17850.TU5/16X..01 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 5/16-18 1-1 1/4-1 1/2 1,82-1,86-1,90

F17850.TU3/8X..01 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 3/8-16 1-1 1/4-1 1/2-2 2,03-2,1-2,17-2,24

F17850.TU1/2X2501 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 1/2-13 1 2,29

F17860.TU5/6X3201 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 5/16-18 1 1/4 2,50

F17860.TU3/8X..01 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 3/8-16 1-1 1/4-1 1/2-2 2,72-2,79-2,85-3

F17860.TU1/2X..01 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 1/2-13 1-1 1/4-1 1/2-2 3,47-3,65-3,79-4,1


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID 6 LOBE HANDWHEEL WITH MALE THREADED STUD



Surface:Satin.



SpeciAl reQUeSTS:




lM = Maximum mouldable length.Enter the stud length choice in the two .. of the article code. Lengths by request with 250 pieces minimum quantity.

+275°-13°


PA6+GF

UL94HB

+135°-20°

f178 cin

D

h3

d3

d

mc

HQ

d1

F Art. D H d c m d3 h3 lM d1 2A Q q ozF17830.TU10/24X..01ciN 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 10/24 1/2 - 3/4 0,46-0,52

F17830.TU1/4X..01ciN 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 1/4-20 1/2 - 3/4 - 1 0,53-0,58-0,62

F17830.TU5/16X..01ciN 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 5/16-18 1/2 - 3/4 - 1 0,65-0,71-0,81

F17830.TU3/8X1901ciN 1,1811 0,8661 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 3/8-16 3/4 0,97

F17840.TU1/4X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 1/4-20 1/2-3/4-1-1 1/40,85-0,88-0,92-

0,96

F17840.TU5/16X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 5/16-183/4-1-1 1/4- 1

1/21,05-1,11-1,18-

1,25

F17840.TU3/8X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 5,1181 3/8-16 3/4-1-1 1/4 1,28-1,38-1,45

F17850.TU5/16X..01ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 5/16-18 1-1 1/4-1 1/2 1,82-1,86-1,90

F17850.TU3/8X..01ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 3/8-16 1-1 1/4-1 1/2-22,03-2,1-2,17-

2,24

F17850.TU1/2X2501ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 5,1181 1/2-13 1 2,29

F17860.TU5/6X3201ciN 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 5/16-18 1 1/4 2,50

F17860.TU3/8X..01ciN 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 3/8-16 1-1 1/4-1 1/2-2 2,72-2,79-2,85-3

F17860.TU1/2X..01ciN 2,3622 1,3386 0,9449 0,6299 0,7087 0,7087 0,0591 5,1181 1/2-13 1-1 1/4-1 1/2-23,47-3,65-3,79-

4,1


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 6 LOBE HANDWHEEL WITH STAINLESS STEEL MALE THREADED STUD


Surface:Satin.


Main Insert:Stainless steel threaded stud (AISI 303) (tolerance 2A).

SpeciAl reQUeSTS:





+275°-13°



H

d3

d1

Q

h3

cm

d

d2

D

PA6+GF

UL94HB

+135°-20°

F275-f275cin

F Art. D d d2 H m c d1 2B Q q ozF27530.TU1/401 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 0,4724 0,88

F27540.TU5/1601 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16-18 0,5512 1,38

F27550.TU3/801 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 0,6299 2,33

F27560.TU1/201 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 0,7874 3,71

F Art. D d d2 H m c d1 2B Q q ozF27530.TU1/401ciN 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 0,4724 0,88

F27540.TU5/1601ciN 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16-18 0,5512 1,38

F27550.TU3/801ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 0,6299 2,33

F27560.TU1/201ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 0,7874 3,71


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 6 lobe handwheel with steel/STAINLESS STEEL

hub and threaded hole

Version F275: Zinc plated steel

Version F275 CIN: Stainless steel AISI 303


Surface:Satin.


Inserts:F275: Zinc plated steel insert with female blind threaded hole (thread tolerance 2B).F275 CIN: Stainless steel (AISI 303) insert with female blind threaded hole (thread tolerance 2B).

SpeciAl reQUeSTS:

• It’s possible to supply the inserts with d1 bore by customer design, on request and for quantities.


+275°-13°


HD

d3

h3

cm

d

d2

d1

Q

F276-f276cinPA6+GF

UL94HB

+135°-20°

F Art. D d d2 H m c d1 H10 Q q ozF27630.TD1/401 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4 0,4724 0,92

F27640.TD5/1601 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16 0,5512 1,41

F27650.TD3/801 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8 0,6299 2,37

F27660.TD1/201 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2 0,7874 3,60

F Art. D d d2 H m c d1 H9 Q q ozF27630.TD1/401ciN 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4 0,4724 0,92

F27640.TD5/1601ciN 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16 0,5512 1,41

F27650.TD3/801ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8 0,6299 2,37

F27660.TD1/201ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2 0,7874 3,60


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115





hub and SMOOTH holeMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Inserts:F276: Zinc plated steel insert with female blind smooth hole (tolerance H10).F276 CIN: Stainless steel (AISI 303) insert with female blind smooth hole (tolerance H9).

SpeciAl reQUeSTS:



+275°-13°



h3

HD

d1

cm

d

d2

Q

d3

PA6+GF

UL94HB

+135°-20°

F277-f277Pin

F Art. D d d2 d3 H h3 m c d1 2B Q q ozF27730.TU1/401 1,1811 0,5118 0,5906 0,3150 0,8661 0,1575 0,4331 0,4331 1/4-20 0,7087 0,85

F27740.TU5/1601 1,5748 0,5906 0,6693 0,4331 0,9449 0,2362 0,4724 0,4724 5/16-18 0,7087 1,20

F27750.TU3/801 1,9685 0,7087 0,7874 0,5118 1,1417 0,2756 0,5906 0,5512 3/8-16 0,8661 2,08

F27760.TU1/201 2,3622 0,7874 0,9449 0,6299 1,3386 0,2362 0,7087 0,6299 1/2-13 1,1024 3,46

F Art. D d d2 d3 H h3 m c d1 2B Q q ozF27730.TU1/401piN 1,1811 0,5118 0,5906 0,3150 0,8661 0,1575 0,4331 0,4331 1/4-20 0,7087 0,85

F27740.TU5/1601piN 1,5748 0,5906 0,6693 0,4331 0,9449 0,2362 0,4724 0,4724 5/16-18 0,7087 1,20

F27750.TU3/801piN 1,9685 0,7087 0,7874 0,5118 1,1417 0,2756 0,5906 0,5512 3/8-16 0,8661 2,08

F27760.TU1/201piN 2,3622 0,7874 0,9449 0,6299 1,3386 0,2362 0,7087 0,6299 1/2-13 1,1024 3,46


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115



Version F277 PIN: Stainless steel AISI 303


Surface:Satin.


Inserts:F277 Zinc plated steel insert with female right through threaded hole (tolerance 2B).F277 PIN: Stainless steel (AISI 303) insert with female right through threaded hole (tolerance 2B).

SpeciAl reQUeSTS:



SOLID 6 lobe handwheel with steel/STAINLESS STEEL hub and RIGHT THROUGH threaded hole

+275°-13°


H

d3

h3

cm

d1

Q

dd2

D

F278-f278cinPA6+GF

UL94HB

+135°-20°

F Art. D d d2 H m c d1 2A Q lM q ozF27830.TU1/4X2501 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 1 1,7717 1,20

F27840.TU5/16X2501 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16-18 1 2,1654 1,91

F27850.TU3/8X3801 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 1 1/2 2,3622 3,39

F27860.TU1/2X3801 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 1 1/2 2,3622 5,26

F Art. D d d2 H m c d1 2A Q lM q ozF27830.TU1/4X2501ciN 1,1811 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 1 1,3780 1,20

F27840.TU5/16X2501ciN 1,5748 0,5906 0,6693 0,9449 0,4724 0,4724 5/16-18 1 1,7717 1,91

F27850.TU3/8X3801ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 1 1/2 1,9685 3,39

F27860.TU1/2X3801ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 1 1/2 1,9685 5,26


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115





hub and threaded STUDMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Inserts:F278: Zinc plated steel insert with male threaded stud (tolerance 2A).F278 CIN: Stainless steel (AISI 303) insert with male threaded stud (tolerance 2A).

SpeciAl reQUeSTS:

It is possible to supply inserts in different lengths or by special design, on request and for quantities.


lM = Maximum turning length.


+275°-13°



PA6+GF

UL94HB

+135°-20°

F186

Q

d3 h3d

H

cm

D

d1

F Art. D H d c m d3 h3 d1 2B Q q ozF18632.TU10/2401 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 10/24 0,5512 0,41F18632.TU1/401 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 1/4-20 0,3937 0,42F18632.TU5/1601 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 5/16-18 0,5512 0,44F18632.TU3/801 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 3/8-16 0,5512 0,46F18640.TU1/401 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 1/4-20 0,6299 0,53F18640.TU5/1601 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 5/16-18 0,5512 0,56F18640.TU3/801 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 3/8-16 0,5512 0,60F18650.TU1/401 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 1/4-20 0,6299 0,88F18650.TU5/1601 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 5/16-18 0,5512 0,92F18650.TU3/801 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 3/8-16 0,5512 0,95F18650.TU1/201 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 1/2-13 0,7087 1,02F18660.TU5/1601 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 5/16-18 0,7480 1,41F18660.TU3/801 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 3/8-16 0,8268 1,52F18660.TU1/201 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 1/2-13 0,7087 1,55


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID CROSS HANDWHEEL WITH FEMALE THREADED INSERT


Surface:Satin.



SpeciAl reQUeST:



+275°-13°

+275°-13°


PA6+GF

UL94HB

+135°-20°

F186 CIN

Q

d3 h3

d

H

cm

D

d1

F Art. D H d c m d3 h3 d1 2B Q q ozF18632.TU1/401ciN 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 1/4-20 0,3937 0,42F18632.TU5/1601ciN 1,2598 0,9055 0,5906 0,4331 0,4724 0,4331 0,0591 5/16-18 0,5512 0,44F18640.TU1/401ciN 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 1/4-20 0,6299 0,53F18640.TU5/1601ciN 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 5/16-18 0,5512 0,56F18640.TU3/801ciN 1,5748 0,9646 0,6299 0,4724 0,4921 0,5118 0,0591 3/8-16 0,5512 0,60F18650.TU5/1601ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 5/16-18 0,5512 0,92F18650.TU3/801ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 3/8-16 0,5512 0,95F18650.TU1/201ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,0787 1/2-13 0,7087 1,02F18660.TU5/1601ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 5/16-18 0,7480 1,41F18660.TU3/801ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 3/8-16 0,8268 1,52F18660.TU1/201ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0787 1/2-13 0,7087 1,55


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID CROSS HANDWHEEL WITH FEMALE THREADED STAINLESS STEEL INSERT



Surface:Satin.


Main Insert:Stainless steel blind threaded bush (AISI 303) (tolerance 2B).

SpeciAl reQUeST:


+275°-13°



PA6+GF

UL94HB

+135°-20°

F187

Q

d3

h3

d

H

cm

D

d1

F Art. D H d c m d3 h3 d1 H7 Q q gF18732.TD1/401 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 1/4 0,5905 13F18732.TD5/1601 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 5/16 0,5905 14F18740.TD1/401 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 1/4 0,5905 18F18740.TD5/1601 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 5/16 0,5905 21F18740.TD3/801 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 3/8 0,6692 20F18750.TD1/401 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 1/4 0,5905 29F18750.TD5/1601 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 5/16 0,5905 31F18750.TD3/801 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 3/8 0,6692 32F18760.TD5/1601 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 (*) 5/16 0,7086 70F18760.TD3/801 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 (*) 3/8 0,9842 65F18760.TD1/201 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 (*) 1/2 0,8661 60


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID CROSS HANDWHEEL WITH SMOOTH BORED INSERT


Surface:Satin.


Main Insert:Brass insert with smooth blind hole (tolerance H7).

(*) Zinc plated steel insert with smooth blind hole (tolerance H10).ATTENTION: bore cannot be enlarged.

SpeciAl reQUeST:



+275°-13°


d3

d

H

cm

D

Qh3

d1

PA6+GF

UL94HB

+135°-20°

F188

F Art. D H d c m d3 h3 d1 2B Q q ozF18832.TU1/401 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 1/4-20 0,7087 0,37F18832.TU5/1601 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 5/16-18 0,7087 0,39F18840.TU1/401 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 1/4-20 0,7087 0,46F18840.TU5/1601 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 5/16-18 0,7087 0,53F18840.TU3/801 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 3/8-16 0,7087 0,56F18850.TU5/1601 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 5/16-18 0,7087 0,85F18850.TU3/801 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 3/8-16 0,7087 0,88F18850.TU1/201 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 1/2-13 0,7087 0,92F18860.TU5/1601 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 5/16-18 0,7087 1,20F18860.TU3/801 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 3/8-16 0,7087 1,34F18860.TU1/201 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 1/2-13 0,7087 1,41


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID CROSS HANDWHEEL WITH FEMALE RIGHT THROUGH

THREADED INSERT



Surface:Satin.


Main Insert:Brass right through threaded bush (tolerance 2B).

SpeciAl reQUeST:



+275°-13°



PA6+GF

UL94HB

+135°-20°

F188 cin

d3

d

H

cm

D

Qh3

d1

F Art. D H d c m d3 h3 d1 2B Q q ozF18832.TU1/401piN 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 1/4-20 0,7087 0,37F18832.TU5/1601piN 1,2598 0,9055 0,5906 0,4331 0,4331 0,3937 0,1969 5/16-18 0,7087 0,39F18840.TU1/401piN 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 1/4-20 0,7087 0,46F18840.TU5/1601piN 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 5/16-18 0,7087 0,53F18840.TU3/801piN 1,5748 0,9646 0,6299 0,4724 0,4921 0,4724 0,2559 3/8-16 0,7087 0,56F18850.TU5/1601piN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 5/16-18 0,7087 0,85F18850.TU3/801piN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 3/8-16 0,7087 0,88F18850.TU1/201piN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5512 0,4331 1/2-13 0,7087 0,92F18860.TU5/1601piN 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 5/16-18 0,7087 1,20F18860.TU3/801piN 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 3/8-16 0,7087 1,34F18860.TU1/201piN 2,3622 1,3386 0,9449 0,6102 0,7283 0,6299 0,6299 1/2-13 0,7087 1,41


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID CROSS HANDWHEEL WITH FEMALE RIGHT THROUGH THREADED

STAINLESS STEEL INSERTMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Main Insert:Stainless steel right through threaded bush (AISI 303) (tolerance 2B).

SpeciAl reQUeST:


+275°-13°


d3

H

cm

D

d

Q

d1

h3

PA6+GF

UL94HB

+135°-20°

F189

F Art. D H d c m d3 h3 lM d1 2A Q q ozF18932.TU1/4X..01 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 1/4-20 1/2 - 1 0,53-0,58F18932.TU5/16X..01 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 5/16-18 1/2 - 1 0,63-0,78F18932.TU3/8X2501 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 3/8-16 1 0,90F18940.TU1/4X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 1/4-20 1/2 - 3/4 - 1 0,66-0,69-0,71

F18940.TU5/16X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 5/16-18 3/4 - 1 - 1 1/2 0,81-0,93-1,14F18940.TU3/8X..01 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 3/8-16 1/2 - 1 0,93-1,14F18950.TU5/16X..01 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 5/16-18 3/4-1-1 1/4 1,3-1,41-1,52

F18950.TU3/8X..01 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 3/8-16 3/4-1-1 1/2-21,32-1,41-1,52

1,78F18950.TU1/2X..01 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 1/2-13 3/4-1-1 1/2 1,78-1,9-2,18F18960.TU5/16X1901 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 5/16-18 1 1,65

F18960.TU3/8X..01 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 3/8-163/4-1-1 1/4-

1 1/2 - 22,24-2,33-2,43-

2,50-2,70

F18960.TU1/2X..01 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 1/2-131-1 1/4 -1 1/2 - 2

2,87-3,05-3,153,53


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID CROSS HANDWHEEL WITH THREADED STUD



Surface:Satin.



SpeciAl reQUeSTS:






+275°-13°



PA6+GF

UL94HB

+135°-20°

F189 cin

d3

H

cm

D

d

Q

d1

h3

F Art. D H d c m d3 h3 lM d1 2A Q q ozF18932.TU1/4X..01ciN 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 1/4-20 1/2 - 1 0,53-0,58

F18932.TU5/16X..01ciN 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 5/16-18 1/2 - 1 0,63-0,78

F18932.TU3/8X2501ciN 1,2598 0,9055 0,5906 0,4331 0,4331 0,3543 0,0591 3,1496 3/8-16 1 0,90

F18940.TU1/4X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 1/4-20 1/2 - 3/4 - 1 0,66-0,69-0,71

F18940.TU5/16X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 5/16-18 3/4 - 1 - 1 1/2 0,81-0,93-1,14

F18940.TU3/8X..01ciN 1,5748 0,9646 0,6693 0,4724 0,4921 0,4724 0,0394 3,1496 3/8-16 1/2 - 1 0,93-1,14

F18950.TU5/16X..01ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 5/16-18 3/4-1-1 1/4 1,3-1,41-1,52

F18950.TU3/8X..01ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 3/8-16 3/4-1-1 1/2-21,32-1,41-1,52

1,78

F18950.TU1/2X..01ciN 1,9685 1,1417 0,7874 0,5512 0,5906 0,5709 0,0591 3,1496 1/2-13 3/4-1-1 1/2 1,78-1,9-2,18

F18960.TU5/16X1901ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 5/16-18 1 1,65

F18960.TU3/8X..01ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 3/8-163/4-1-1 1/4-

1 1/2 - 22,24-2,33-2,43-

2,50-2,70

F18960.TU1/2X..01ciN 2,3622 1,3386 0,9449 0,6102 0,7283 0,7087 0,0591 3,1496 1/2-131-1 1/4 -1 1/2 - 2

2,87-3,05-3,153,53


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID CROSS HANDWHEEL WITH THREADED STAINLESS

STEEL STUDMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Main Insert:Stainless steel threaded stud (AISI 303) (tolerance 2A).

SpeciAl reQUeSTS:




+275°-13°


d3

c

d1

h3Q

m

H

d2

Q2

D

d

F271-F271PINPA6+GF

UL94HB

+135°-20°

F Art. D d d2 d3 H h3 m c d1 Q Q2 q ozF27140.TU5/1601p 1,5748 0,6299 0,3346 0,5512 1,0236 0,1575 0,5512 0,4724 5/16-18 0,8661 1,3780 1,09

F27150.TU3/801p 1,9685 0,7874 0,4134 0,7087 1,3386 0,1575 0,7874 0,5512 3/8-16 1,1811 1,6929 2,22

F Art. D d d2 d3 H h3 m c d1 Q Q2 q ozF27140.TU5/1601piN 1,5748 0,6299 0,3346 0,5512 1,0236 0,1575 0,5512 0,4724 5/16-18 0,8661 1,3780 1,09

F27150.TU3/801piN 1,9685 0,7874 0,4134 0,7087 1,3386 0,1575 0,7874 0,5512 3/8-16 1,1811 1,6929 2,22


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


Surface:Satin.


Inserts:F271 Zinc plated steel insert with female right through threaded hole with groove for quick release.F271 PIN: Stainless steel (AISI 303) insert with female right through threaded hole with groove for quick release.

SpeciAl reQUeSTS:

• None.

ATTENTION:TO GUARANTEE CORRECT OPERATION OF THE QUICK RELEASE HANDWHEEL, THE THREADED STUD MUST HAVE A MINIMUM LENGTH OF Q2.

SOLID CROSS HANDWHEEL WITH STEEL HUB AND QUICK RELEASE

THREADED BORE




+275°-13°



F269PA6+GF

UL94HB

+135°-20°

H

cm

D

d

E

A

Q

d1

Ht

F Art. D d H Ht A e m c d1 2B Q q ozF26950.TU1/401 1,9685 0,7087 1,1417 1,5354 0,3937 % 0,6693 0,5906 0,5512 1/4-20 0,9843 2,54

F26950.TU5/1601 1,9685 0,7087 1,1417 1,5354 0,3937 % 0,6693 0,5906 0,5512 5/16-18 0,9843 2,36

F26950.TU3/801 1,9685 0,7087 1,1417 1,5354 0,3937 % 0,6693 0,5906 0,5512 3/8-16 0,9843 2,12


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


Surface:Satin.


Insert:Nickel plated brass hexagonal insert with female blind threaded hole (thread tolerance 2B). SpeciAl reQUeSTS:


ATTENTION:FOR NORMAL TIGHTNESS SIMPLY ROTATE THEKNOB. FOR MORE TIGHTNESS, INSERT AN ALLENWRENCH IN THE HEXAGON.

high clamping SOLIDcross handwheel

with threaded insert


+275°-13°


PA6+GF

UL94HB

+135°-20°

F270

H

cm

D

d

A

Ht

B

Q

d1E

d2

F Art. D d d2 H Ht A B e m c d1 2A Q q ozF27050.TU3/8X2501 1,9685 0,7087 0,5906 0,9449 1,3386 0,3937 0,1575 % 0,6693 0,5906 0,5512 3/8-16 1 3,42


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


Surface:Satin.


Insert:Nickel plated brass hexagonal insert with male threaded stud (thread tolerance 2A).

SpeciAl reQUeSTS:



ATTENTION:FOR NORMAL TIGHTNESS SIMPLY ROTATE THEKNOB. FOR MORE TIGHTNESS, INSERT AN ALLENWRENCH IN THE HEXAGON.


high clamping SOLIDcross handwheel

with threaded STUD+275°-13°



H

c

m

D

d

d2

d1

Q

PA6+GF

UL94HB

+135°-20°

F286-f286cin

F Art. D d d2 H m c d1 2B Q q ozF28632.TU1/401 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 0,4724 0,81

F28640.TU5/1601 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16-18 0,5512 1,13

F28650.TU3/801 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 0,6299 1,90

F28660.TU1/201 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 0,7874 3,17

F Art. D d d2 H m c d1 2B Q q ozF28632.TU1/401ciN 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 0,4724 0,81

F28640.TU5/1601ciN 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16-18 0,5512 1,13

F28650.TU3/801ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 0,6299 1,90

F28660.TU1/201ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 0,7874 3,17


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115




SOLID CROSS handwheel with steel/STAINLESS STEEL

hub and threaded holeMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Inserts:F286: Zinc plated steel insert with female blind threaded hole (thread tolerance 2B).F286 CIN: Stainless steel (AISI 303) insert with female blind threaded hole (thread tolerance 2B).

SpeciAl reQUeSTS:



+275°-13°


H

c

m

D

d

d2

d1Q

F287-f287cinPA6+GF

UL94HB

+135°-20°

F Art. D d d2 H m c d1 H10 Q q ozF28732.TD1/401 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4 0,4724 0,85

F28740.TD5/1601 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16 0,5512 1,23

F28750.TD3/801 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8 0,6299 2,01

F28760.TD1/201 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2 0,7874 3,00

F Art. D d d2 H m c d1 H9 Q q ozF28732.TD0601ciN 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4 0,4724 0,85

F28740.TD0801ciN 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16 0,5512 1,23

F28750.TD1001ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8 0,6299 2,01

F28760.TD1201ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2 0,7874 3,00


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


hub and BORED hole




Surface:Satin.


Inserts:F287: Zinc plated steel insert with female blind smooth hole (tolerance H10).F287 CIN: Stainless steel (AISI 303) insert with female blind smooth hole (tolerance H9).

SpeciAl reQUeSTS:




+275°-13°



d3

H

c

m

D

d

d2

d1

h3Q

PA6+GF

UL94HB

+135°-20°

F288-f288Pin

F Art. D d d2 d3 H h3 m c d1 2B Q q ozF28832.TU1/401 1,2598 0,5118 0,5906 0,3150 0,8661 0,1575 0,4331 0,4331 1/4-20 0,7087 0,74

F28840.TU5/1601 1,5748 0,5512 0,6299 0,4331 0,9449 0,2362 0,4724 0,4724 5/16-18 0,7087 0,99

F28850.TU3/801 1,9685 0,7087 0,7874 0,5512 1,1417 0,2756 0,5906 0,5512 3/8-16 0,8661 1,73

F28860.TU1/201 2,3622 0,7874 0,9449 0,6299 1,3386 0,2362 0,7087 0,6299 1/2-13 1,1024 2,86

F Art. D d d2 d3 H h3 m c d1 2B Q q ozF28832.TU1/401piN 1,2598 0,5118 0,5906 0,3150 0,8661 0,1575 0,4331 0,4331 1/4-20 0,7087 0,74

F28840.TU5/1601piN 1,5748 0,5512 0,6299 0,4331 0,9449 0,2362 0,4724 0,4724 5/16-18 0,7087 0,99

F28850.TU3/801piN 1,9685 0,7087 0,7874 0,5512 1,1417 0,2756 0,5906 0,5512 3/8-16 0,8661 1,73

F28860.TU1/201piN 2,3622 0,7874 0,9449 0,6299 1,3386 0,2362 0,7087 0,6299 1/2-13 1,1024 2,86


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115




SOLID CROSS handwheel with steel/STAINLESS STEEL hub and RIGHT THROUGH threaded hole


Surface:Satin.


Inserts:F288 Zinc plated steel insert with female right through threaded hole (tolerance 2B).F288 PIN: Stainless steel (AISI 303) insert with female right through threaded hole (tolerance 2B).

SpeciAl reQUeSTS:



+275°-13°


H

cm

D

d

d2

d1

Q

F289-f289cinPA6+GF

UL94HB

+135°-20°

F Art. D d d2 H m c d1 2A Q lM q ozF28932.TU1/4X2501 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 1 1,7717 1,09

F28940.TU5/16X2501 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16-18 1 2,1654 1,66

F28950.TU3/8X2501 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 1 2,3622 2,89

F28960.TU1/2X2501 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 1 2,3622 4,41

F Art. D d d2 H m c d1 2A Q lM q ozF28932.TU1/4X2501ciN 1,2598 0,5118 0,5906 0,8661 0,4331 0,4331 1/4-20 1 1,3779 1,09

F28940.TU5/16X2501ciN 1,5748 0,5512 0,6299 0,9449 0,4724 0,4724 5/16-18 1 1,7716 1,66

F28950.TU3/8X2501ciN 1,9685 0,7087 0,7874 1,1417 0,5906 0,5512 3/8-16 1 1,968 2,89

F28960.TU1/2X2501ciN 2,3622 0,7874 0,9449 1,3386 0,7087 0,6299 1/2-13 1 1,968 4,41


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115




hub and threaded STUDMaterial:Reinforced polyamide.Oils and greases resistant.

Surface:Satin.


Inserts:F289: Zinc plated steel insert with male threaded stud (tolerance 2A).F289 CIN: Stainless steel (AISI 303) insert with male threaded stud (tolerance 2A).

SpeciAl reQUeSTS:



Enter the stud length choice in the two .. of the article code.

Enter the stud length choice in the two .. of the article code.




+275°-13°



H h

cm

d1d2d

Q

D

d3 h3

PA6+GF

UL94HB

+135°-20°

f661-f761

F Art. D H h d c m d2 d3 h3 d1 2B Q q ozF661045.TU1/401 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 1/4-20 0,3543 0,35F661045.TU5/1601 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 5/16-18 0,4331 0,49F661045.TU3/801 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 3/8-16 0,3937 0,53F661065.TU5/1601 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 5/16-18 0,4331 0,99F661065.TU3/801 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 3/8-16 0,4331 1,02F661065.TU1/201 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 1/2-13 0,5118 1,09F661085.TU5/1601 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 5/16-18 0,5906 1,87F661085.TU3/801 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 3/8-16 0,5512 1,94F661085.TU1/201 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 1/2-13 0,7480 2,12F661105.TU3/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3/8-16 0,6693 3,17F661105.TU1/201 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 1/2-13 0,6693 3,42F661125.TU1/201 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 1/2-13 0,7087 5,64F661125.TU5/801 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 5/8-11 0,7087 5,82

F Art. D H h d c m d2 d3 h3 d1 2B Q q ozF761085.TU5/1601 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 5/16-18 0,5906 1,87F761085.TU3/801 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 3/8-16 0,5512 1,94F761085.TU1/201 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 1/2-13 0,7480 2,12F761105.TU3/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3/8-16 0,6693 3,17F761105.TU1/201 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 1/2-13 0,6693 3,42F761125.TU1/201 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 1/2-13 0,7087 5,64F761125.TU5/801 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 5/8-11 0,7087 5,80


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

SOLID 3 LOBE handwheel with FEMALE threaded INSERT


Material:Reinforced polyamide. Oils and greases resistant.

Surface: Satin.

Colour: Black (RAL 9011).

Main Insert:Brass blind threaded bush (tolerance 2B).(*) Zinc plated steel blind threaded bush (tolerance 2B).

Hub:F661= Solid version.F761= Hollow underneath version.

SpeciAl reQUeSTS:



Version F662: Solid hub

Version F761: Hollow underneath hub

+275°-13°


H h

cm

d

h3

D

d3

Q

d1

f662PA6+GF

UL94HB

+135°-20°

F Art. D H h d c m d3 h3 dm d1 H10 Q q ozF662045.TD1/401 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 0,4331 0,0394 - (*) 1/4 0,3150 0,49

F662065.TD1/401 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 0,6102 0,0591 0,3937 (*) 1/4 0,5118 1,27

F662085.TD1/401 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,8268 0,0787 0,6299 1/4 0,7480 2,54

F662105.TD1/401 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,9843 0,0787 0,7087 1/4 0,9843 3,53

F662125.TD1/401 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,1024 0,0787 0,8661 1/4 1,0630 6,81


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 3 LOBE handwheel with FEMALE BORED INSERT


Surface:Satin.


Main Insert:(*) Brass blind threaded bush (tolerance H7).

Zinc plated steel blind threaded bush (tolerance H10).

SpeciAl reQUeSTS:




Dm = It’s possible to increase the hole, by boring, until Dm (enlarge).

Attention: bore d1 (H10 tolerance) could be produced by request, with 50 pieces minimum.

+275°-13°



PA6+GF

UL94HB

+135°-20°

F663-F763

H h

cm

d1d2d

Q

h3

D

d3 d4

F Art. D H h d c m d2 d3 d4 h3 d1 2B Q q ozF663045.TU1/401 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,3937 0,0394 1/4-20 0,4921 0,39

F663045.TU5/1601 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,3937 0,0394 5/16-18 0,4921 0,39

F663045.TU3/801 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,3937 0,0394 3/8-16 0,4921 0,39

F663065.TU5/1601 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,5315 0,0591 5/16-18 0,6102 0,88

F663065.TU3/801 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,5315 0,0591 3/8-16 0,6102 0,92

F663065.TU1/201 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,5315 0,0591 1/2-13 0,6102 0,99

F663085.TU5/1601 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 5/16-18 0,5315 1,76

F663085.TU3/801 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 3/8-16 0,5315 1,83

F663085.TU1/201 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 1/2-13 0,5315 1,83

F663105.TU3/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 3/8-16 0,9055 3,10

F663105.TU1/201 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 1/2-13 0,9055 3,10

F663105.TU5/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 5/8-11 0,8268 3,21

F663125.TU1/201 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 1,0236 0,0787 1/2-13 1,2205 5,36

F663125.TU5/801 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 1,0236 0,0787 5/8-11 1,2205 5,64

F Art. D H h d c m d2 d3 d4 h3 d1 2B Q q ozF763085.TU5/1601 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 5/16-18 0,5315 1,76

F763085.TU3/801 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 3/8-13 0,5315 1,83

F763085.TU1/201 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,5118 0,0787 1/2-13 0,5315 1,83

F763105.TU3/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 3/8-13 0,9055 3,10

F763105.TU1/201 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 1/2-13 0,9055 3,10

F763105.TU5/801 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,9252 0,0787 5/8-11 0,8268 3,21

F763125.TU1/201 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 1,0236 0,0787 1/2-13 1,2205 5,36

F763125.TU5/801 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 1,0236 0,0787 5/8-11 1,2205 5,50


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


Material:Reinforced polyamide. Oils and greases resistant.

Surface: Satin.

Colour: Black (RAL 9011).

Inserto:Boccola con foro filettato cieco in ottone.(*) Boccola con foro filettato cieco in acciaio zincato.(tolleranza filetti 2B).


SpeciAl reQUeSTS:



Version F663 Solid hub

Version F763: Hollow underneath hub

SOLID 3 LOBE handwheel with FEMALE RIGH THROUGH

threaded INSERT+275°-13°


F664-F764PA6+GF

UL94HB

+135°-20°

H h

cm

h3

D

d3

dd2d1

Q

F Art. D H h d c m d2 d3 h3 lM d1 2A Q q ozF664045.TU1/4X..01 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 2,3622 1/4-20 1/2 - 1 0,42-0,55

F664045.TU5/16X..01 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 2,3622 5/16-18 1/2 - 1 0,60-0,73

F664045.TU3/8X3201 1,7717 0,8268 0,7087 0,6299 0,4331 0,3937 -/- 0,4331 0,0394 2,3622 3/8-16 1 1/4 0,81

F664065.TU5/16X..01 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 3,1496 5/16-18 3/4 - 1 1/4 1,26-1,40

F664065.TU3/8X..01 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 3,1496 3/8-16 3/4 - 1 1/4 1,5-1,69

F664065.TU1/2X3201 2,5591 1,1024 0,9252 0,8661 0,6496 0,4528 -/- 0,6102 0,0591 3,1496 1/2-13 1 1/4 2,10

F664085.TU5/16X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 5/16-18 1 - 1 1/2 2,22-2,41

F664085.TU3/8X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 3/8-16 1 - 1 1/2 2,47-2,78

F664085.TU1/2X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 1/2-13 1 - 1 1/2 3,01-3,28

F664105.TU3/8X..01 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3,1496 3/8-16 1 - 1 1/2 4,01-4,37

F664105.TU1/2X..01 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3,1496 1/2-13 1 1/2 - 2 4,34-4,87

F664125.TU1/2X5101 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 3,9370 1/2-13 2 8,20

F Art. D H h d c m d2 d3 h3 lM d1 2A Q q ozF764085.TU5/16X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 5/16-18 1 - 1 1/4 2,22-2,33

F764085.TU3/8X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 3/8-16 1 1/4 - 1 1/2 2,66-2,79

F764085.TU1/2X..01 3,3465 1,4567 1,2008 1,1811 0,8268 0,6299 0,7087/- 0,8268 0,0787 2,3622 1/2-13 1 - 1 1/2 3,0-3,25

F764105.TU3/8X..01 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3,1496 3/8-16 1 - 2 3,88-4,55

F764105.TU1/2X..01 4,1339 1,8110 1,4764 1,3780 1,0236 0,7480 0,7874/- 0,9843 0,0787 3,1496 1/2-13 1 1/4 - 2 4,32-4,87

F764125.TU1/2X5101 4,9213 2,1260 1,7323 1,6732 1,2205 0,9055 1,0236/- 1,1220 0,0787 3,9370 1/2-13 2 7,62


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115


SOLID 3 LOBE handwheel with MALE threaded STUD


Surface:Satin.




SpeciAl reQUeSTS:




Version F664 Solid hub

Version F764 Hollow underneath hub


+275°-13°



NOTE


( F ) 90%( J ) 40%( K ) 5%( L )

ver. FUS.01-1115

F - SOliD lOcKiNG HANDWHeelS

F - 35

9011

2004

2011

9010

5002

5005

5015

5018

5019

5010

1007

1021

7024

7035

3000

6024

01

02

03

04

05

06

07

19

21

22

09

10

12

13

16

17

RAL Cod.

-

-

pant. 645 U

pant. 300

-

-

NCS 7500

-

-

-

-

-

-

-

52

53

54

55

57

59

60

64

65

66

70

71

72

73

Ref. Cod.

BOTECO ® - © All right reserved - www.boteco.itAny unathorized reproduction is strictly forbidden

Black

Orange

Orange

White

Blue

Blue

Blue

Blue

Blue

Blue

Yellow

Yellow

Grey

Grey

Red

Green

Colour

RAL COLOURS CODING

White

Blue

Blue

Blue

Grey

Grey

Grey

Red

Red

Natural

Green

Brown

Cream

Violet

Colour

OTHER COLORS

Colour Chart

F - SOliD lOcKiNG HANDWHeelS

Ph

: D

VR

FO

TO

GR

AF

IA -

Mar

ano

Vic

. ;

Gra

ph

ics

and

Pri

nti

ng

: J.

Pie

trib

iasi

- M

.Bo

rgo

- B

ote

co ®

; © A

ll ri

gh

ts r

eser

ved

An

y u

nat

ho

rize

d r

epro

du

ctio

n is

str

ictl

y fo

rbid

den

E-CATALOGUE

BOTECO Srlwww.boteco.it

36010 ZANE’ (VI) - ITALY

Via L. Pettinà 16 ( side street of Via Cuso)

Switchboard Tel.:+39-0445-316411 - Fax:+39-0445-316400

Sales Fax:+39-0445-316401 mail: [email protected]

Administration Fax:+39-0445-316402 mail: [email protected]

Technical Fax:+39-0445-316404 mail: [email protected]

Certifi ed Mail Box: [email protected]

AUTHORISED RESELLER

ver. FUS.01-1115

Documents

FAMILy - F solid locking handwheels - Boteco America · 2016. 11. 14. · F110 F Art. D d H m c d1 2B Q q oz F110022.TN10/3201 0,866 0,472 0,689 0,433 0,256 10/32 0,315 0,194