1
Part No Pack Size Barcode Carton QTY L90 125 ml 9311090000759 6 Nulon Products Australia Pty Ltd 17 Yulong Close, Moorebank NSW 2170 Web: www.nulon.com.au AUS info line: 1800 679 922 NZ info line: 0800 454 108 Australian Made & Owned Extreme Pressure Anti-Seize Lubricant Nulon Extreme Pressure Anti-Seize Lubricant is a complex bentone based lubricating paste containing a high percentage of polytetrafluoroethylene (PTFE). Nulon L90 provides extremely high film strength and adhesion, protecting against initial start-up damage of machinery even after long periods of lay-up. Nulon L90 provides long-term lubrication of components that are otherwise difficult or impossible to lubricate after initial assembly. Most chemicals, solvents and corrosive agents do not affect Nulon L90. L90 does not dry or harden with age and offers performance over a wide temperature range. L90 protects exposed components against rust during lay-up. L90 permits more even torque pressures and faster breakouts of threads, joints, flanges and gaskets. Benefits • Minimises initial start-up damage • Seals gasket surfaces without adhering • Seals threads up to 8mm diameter • Reduces possibility of seizing • Reduces wear and friction • Protects against corrosion • Resists water wash out Offers a high degree of residual lubrication Typical Applications Applications for L90 are limited only by the user’s imagination. The following are only indicative of the potential applications for L90. Tests ASTM Nulon L90 Colour Cream Flash point, COC, °C D92 194 Foam characteristics D892 Nil Viscosity @ 40°C, cSt D445 452 Viscosity @ 100°C, cSt D445 000 Viscosity index D2270 1A Density K/l D1298 0.9476 Pour point °C D97 -18 Melt point of PTFE °C D1457 >325 Due to continued product research and development the information contained in this Product Bulletin is subject to change without notification. Engine Assembly • Camshafts and followers • All bearing surfaces • Shoulders of head studs • Threads (particularly those to be torqued) • Valve stems and seals • Oil seals • Gasket surfaces General Automotive • Propeller shaft spline • Ignition points rubbing blocks • Anti-squeal for brake pads • Assembly of differentials • Hinge pins • Door locks • Assembly of gearboxes • Prime mover turntables Marine • Cables • Winches • Pump assemblies • Steering stems and cables • Propeller shafts • Seals Agriculture • Exposed chains and gears • Splines • Slides • Seals • Pumps • Assembly of all agricultural machinery Industry • Slides and guides • Cables and pulleys • Railway points • Bushes and pins • Hinges of all types • Camshaft lobes • Threads • Splines • Sewing machines • Machine assembly • Assembly lubricant, particularly where subsequent lubrication is difficult

Extreme Pressure Anti-Seize Lubricant · Part No Pack Size Barcode Carton QTY L90 125 ml 9311090000759 6 Nulon Products Australia Pty Ltd 17 Yulong Close, Moorebank NSW 2170 Web:

  • Upload
    others

  • View
    4

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Extreme Pressure Anti-Seize Lubricant · Part No Pack Size Barcode Carton QTY L90 125 ml 9311090000759 6 Nulon Products Australia Pty Ltd 17 Yulong Close, Moorebank NSW 2170 Web:

Part No Pack Size Barcode Carton QTY

L90 125 ml 9311090000759 6

Nulon Products Australia Pty Ltd 17 Yulong Close, Moorebank NSW 2170Web: www.nulon.com.auAUS info line: 1800 679 922NZ info line: 0800 454 108

Australian Made & Owned

Extreme Pressure Anti-Seize Lubricant

Nulon Extreme Pressure Anti-Seize Lubricant is a complex bentone based lubricating paste containing a high percentage of polytetrafluoroethylene (PTFE). Nulon L90 provides extremely high film strength and adhesion, protecting against initial start-up damage of machinery even after long periods of lay-up. Nulon L90 provides long-term lubrication of components that are otherwise difficult or impossible to lubricate after initial assembly. Most chemicals, solvents and corrosive agents do not affect Nulon L90. L90 does not dry or harden with age and offers performance over a wide temperature range. L90 protects exposed components against rust during lay-up. L90 permits more even torque pressures and faster breakouts of threads, joints, flanges and gaskets.

Benefits• Minimises initial start-up damage• Seals gasket surfaces without adhering• Seals threads up to 8mm diameter• Reduces possibility of seizing• Reduces wear and friction• Protects against corrosion• Resists water wash out• Offers a high degree of residual lubrication

Typical Applications

Applications for L90 are limited only by the user’s imagination. The following are only indicative of the potential applications for L90.

Tests ASTM Nulon L90

Colour Cream

Flash point, COC, °C D92 194

Foam characteristics D892 Nil

Viscosity @ 40°C, cSt D445 452

Viscosity @ 100°C, cSt D445 000

Viscosity index D2270 1A

Density K/l D1298 0.9476

Pour point °C D97 -18

Melt point of PTFE °C D1457 >325

Due to continued product research and development the information contained in this Product Bulletin is subject to change without notification.

Engine Assembly• Camshafts and followers• All bearing surfaces• Shoulders of head studs• Threads (particularly

those to be torqued)• Valve stems and seals• Oil seals• Gasket surfacesGeneral Automotive• Propeller shaft spline• Ignition points rubbing

blocks• Anti-squeal for brake

pads• Assembly of differentials• Hinge pins• Door locks• Assembly of gearboxes• Prime mover turntablesMarine• Cables• Winches• Pump assemblies• Steering stems and

cables• Propeller shafts• Seals

Agriculture• Exposed chains and

gears• Splines• Slides• Seals• Pumps• Assembly of all

agricultural machineryIndustry• Slides and guides• Cables and pulleys• Railway points• Bushes and pins• Hinges of all types• Camshaft lobes• Threads• Splines• Sewing machines• Machine assembly• Assembly lubricant,

particularly where subsequent lubrication is difficult