BORLA PERFORMANCE INDUSTRIES

5901 Edison Dr.

Oxnard, Ca. 93033

805-986-8600

TITLE: Hyundai Genesis Coupe Installation Instructions

PART NO. A-35522 Rev. A Page 1 of 4

Exhaust System Installation for Hyundai Genesis Coupe

PN 140350

Thank you for purchasing a Borla Performance Cat-Back™ Exhaust System.

Borla Performance Cat-Back™ Exhaust System (Part number 140350) has been designed for the Hyun-

dai Genesis Coupe with 2.0L Turbo engine, rear-wheel drive, and manual or automatic transmission.

Borla Performance Industries recommends that an exhaust shop or professional after market parts installer perform the installation

of this system. However, if you decide to perform the installation on your own it is recommended that two people are used. This

installation should not be performed by one person due to the risk of injury. Ensure the installers use all under car safety precautions

including eye protection.

Please take time to read and understand the following…

By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms

stated below.

It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your

Borla Performance Exhaust System

Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper

operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s

products and/or systems.

Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on

your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your

new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.

These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please

read this document completely before beginning the installation of your system.

Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for

this installation.

To ensure this part number fits your specific model year, please visit our website for the latest model year listings at

www.BORLA.com.

BORLA PERFORMANCE INDUSTRIES

5901 Edison Dr.

Oxnard, Ca. 93033

805-986-8600

TITLE: Hyundai Genesis Coupe Installation Instructions

PART NO. A-35522 Rev. A Page 2 of 4

Minimum Required Tool List: TOOLS:

1 3/8” Drive Ratchet

2 3/8” Drive Extension 3”

3 15mm Socket

4 Pry Bar

SHOP SUPPLIES:

1 Spray Lubricant

Borla Performance Cat-Back™ Bill of Materials

1. Front pipe assembly

2. Intermediate pipe assembly

3. Muffler assembly

4. 3.00” clamp

5. Bolt M10 x 1.25p x 30.7 (QTY 2) 6. Washer, M10 (QTY 4)

7. Nut M10 x 1.50p (QTY 2)

BORLA PERFORMANCE INDUSTRIES

5901 Edison Dr.

Oxnard, Ca. 93033

805-986-8600

TITLE: Hyundai Genesis Coupe Installation Instructions

PART NO. A-35522 Rev. A Page 3 of 4

Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the

exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle.

Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance

Cat-Back Exhaust System.

Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the

removal of your old exhaust system from your vehicle.

Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of

materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla

Performance Cat-Back Exhaust System.

Original Exhaust System

Removal Note: With a used vehicle, we suggest a penetrating spray lubricant to be

applied liberally to all exhaust fasteners and allowing a significant period

of time for the chemical to lubricate the threads before attempting to

disassemble.

1. Unbolt the flange located behind the catalytic converter. Place the hard-

ware to the side for use during the installation of your new exhaust sys-

tem. (See Fig. 1)

2. Remove the cross-brace and save the hardware for installation.

(See Fig. 2)

3. Lubricate all the hangers and rubber isolators.

4. Using a muffler stand or an additional person to hold the rear muffler

into position, remove the hangers from the rubber isolators and remove

the rear muffler from the vehicle. (See Fig. 3)

5. Remove the rubber isolator as shown. This will be re-used for the in-

stallation of your new Borla Cat-Back exhaust.

Figure 1

Figure 2

Warning: Use extreme caution during installation. Torque all

fasteners according to manufacturer’s torque values and

tightening sequence. DO NOT use air impact tools to tighten

fasteners on Borla Performance Exhaust Systems. Use of such

tools may result in bent flanges or gasket contact areas leading to

exhaust leaks.

Figure 3

Figure 4

BORLA PERFORMANCE INDUSTRIES

5901 Edison Dr.

Oxnard, Ca. 93033

805-986-8600

TITLE: Hyundai Genesis Coupe Installation Instructions

PART NO. A-35522 Rev. A Page 4 of 4

Borla Performance Cat-Back

Exhaust System Installation

1. Using the original hardware, place the front pipe assembly into

position. Hand tighten the hardware for now. (See Figs. 5 & 6)

2. Place a clamp over the expanded end of the Intermediate Pipe

and set it into position making sure to install the hanger into the

rubber isolator. (See Fig. 7) Do Not tighten the clamp.

3. Carefully install the Muffler Assembly making sure to install the

hangers into the rubber isolators. (See Fig. 8)

4. Attach muffler flanges using supplied hardware. (See Fig. 9)

5. Check your exhaust system for proper clearance under the

vehicle and also for tip alignment.

6. Once position has been determined to be correct, tighten the

Accuseal™ clamp to 32-35 ft. lbs. making sure the clamps

openings are not over any of the notches in the pipes. Tighten the

flange hardware to 18-22 ft. lbs.

7. Before starting your vehicle, make sure to check all wires, hoses,

brake lines, body parts and tires for safe clearance from the

exhaust system.

8. Start vehicle and check for any leaks. If any leaks are found,

determine cause (such as loose hardware or incorrectly

positioned clamp) and repair as necessary.

Figure 6

Figure 7

Note: When you first start your vehicle after the installation

of your new Borla Performance Exhaust System, there may

be some smoke and fumes coming from the system. This is a

protective oil based coating used in the manufacturing of

mandrel bent performance exhaust tubing. This is not a

problem and will disappear within a very short period of

time after the exhaust has reached normal operating

temperatures.

Figure 5

Figure 8

Figure 9