Exercise - Moon Mission

Click here to show toolbars of the Web Online Help System: show toolbars

Exercise: Moon Mission With B-Plane Targeting (Advanced)

Setup | Getting Near the Moon | B-Plane Targeting | Reaching Periselene | Lunar Orbit Insertion

Note: To do this exercise you will need a valid license of STK Professional Edition and STK/Astrogator.

In this exercise you will model a mission to the Moon. Starting from a parking orbit around the Earth, you will perform a

Trans-Lunar Injection to target on the lunar b-plane. You will adjust the size of the maneuver to perform a Lunar Orbit Insertion to

achieve a final circular orbit with an inclination of 90 degrees.

Note: This is an advanced Astrogator exercise, which presupposes familiarity with STK and some previous exposure

to Astrogator. If you are new to STK, it is recommended that you first work through the STK Quick Start, which

gives you a tour of the STK user interface and basic STK functionality. For an entry-level introduction to Astrogator,

try the exercise in which you use the targeter to model a Hohmann transfer.

Setting the Context

To set the context for your moon mission, you will define a scenario with a satellite and three planet objects-- Sun, Earth and

Moon, set up your 2D Graphics window to give an overview of the mission, and define two 3D Graphics windows providing Earth-

and Moon-centered views of the mission.

Note: Throughout this exercise you will open properties pages and dialogs and make various settings. All of the

properties pages and most of the dialogs include an OK button. Unless otherwise instructed, when you finish

making the settings on a given page or dialog, close it by clicking OK.

Designing the Scenario

Create a scenario and name it LunarMission.1.

On the Time page of the scenario's Basic properties, set the Analysis Period Epoch and Start times to 1 Jan 1993

00:00:00.00, and set the Stop time to 1 Jan 1994 00:00:00.00. Within the Animation pane, Stop at Time 1 Jan 1994

00:00:00.00 and set the Step Size to 3 min.

2.

On the scenario's 2D Graphics - Global Attributes page, make the following settings:3.

Exercise - Moon Mission http://www.stk.com/resources/help/online/stk/source/extfile/gator/tx-lun...

1 di 14 12/01/2011 01:31

Property Type Property Recommended Settings

Vehicles

Show Orbits/ Trajectories ON

Show Orbit Markers ON

Other Vehicle Attributes OFF

Planets

Show Orbits ON

Show Inertial Positions ON

Show Position Labels ON

Other Planet Attributes OFF

Defining Planets

Create three planets.1.

Open the Basic - Definition page for one of the planets, and verify that its Central Body field is set to Sun and that the

Auto-Rename option is selected.

2.

Open the Definition page for another of the planets, and change its Central Body to Earth, again verifying that

Auto-Rename is on.

3.

In a similar fashion, select Moon as the Central Body of the remaining planet.4.

Spacecraft Graphics

Create a satellite and name it LunarProbe.1.

On the Basic - Orbit page, set the Propagator to Astrogator.2.

On the Attributes (Custom Intervals) page of the satellite's 2D Graphics properties, click More... for Default Attributes, and

select a simple Marker Style, such as a circle or star.

3.

On the 2D Graphics - Pass page, set Ground Track Lead Type to None and Orbit Track Lead Type to All.4.

On the 3D Graphics - Pass page, under Leading/Trailing, select the option to Inherit from 2D Graphics.5.

On the 3D Graphics - Model page, verify that Orbit Marker is set to Point, and change its Pixel Size to 7. For the Detail

Thresholds, slide the 'Marker, Label' and the 'Marker' bars to their maximum value.

6.

2D Graphics Window

Set up the 2D Graphics window to visualize the orbit on the XY plane as seen from the Sun Ecliptic North (Z Axis):

Open the Properties Browser for the 2D Graphics window.1.

On the Details page, deselect all geographic features in the Items list, uncheck the Show option for Lat/Lon Lines, and

uncheck Background - Image.

2.

On the Projection page, change Projection Format - Type to Orthographic, change Display Coordinate Frame to BBR, and

change Display Height to 900000 (900 thousand) km. Verify that Secondary Body is set to Sun. Change Center - Lat to 89

deg and Lon to -90 deg.

3.

Select the Show Axes option and click Format.... Set the Show options so that only the +X and -X Axes will be displayed.

Select different colors for the two axes (using colors that will show clearly against a black background). Change the scale to

10000 (10 thousand) for both axes, change the Coordinate Frame to BBR, and verify that the Secondary Body is the Sun.

4.


2 di 14 12/01/2011 01:31

The Sun and Anti-Sun lines will now display in the 2D Graphics window:

Tip: Reset the scenario as necessary to update the 2D and 3D Graphics windows.

3D Graphics Window: Earth-Centered

Open the Properties Browser for the 3D Graphics window.1.

On the Grids page, under Space Grid, check the ECI Coordinates option, and verify that Show Radial Lines is checked.2.

Tip: While on this page, you may want to select a relatively muted color for the grid (such as gray or olive

green) so that it does not display in an overly prominent way in the 3D Graphics windows. Otherwise, it may

detract from more important objects, such as orbit paths and the B-plane.


3 di 14 12/01/2011 01:31

On the Advanced Page, set Max Visible Distance to 1e+008 km.4.

3D Graphics Window: Moon-Centered

Make certain that you have applied the changes you made to the properties of the 3D Graphics window, since you will be

using it as the basis for creating a new, Moon-centered view.

1.

From the View menu, select Duplicate 3D Graphics Window -> 3D Graphics 1 - Earth.2.

Select the new 3D Graphics window, click Central Body ( ) and select Moon.3.

Leave all other properties at the settings inherited from the Earth-centered view.4.

Getting Near the Moon

In the following phases of this exercise, you will use Astrogator to:

Set up a Mission Control Sequence (MCS),

Make a first guess for the Trans-Lunar Injection,

Set up the targeter to calculate Launch Epoch and Coast Duration, and

Run the targeter to bring the lunar probe close within the Moon's vicinity.

MCS Setup

On the satellite's Basic - Orbit page, open the MCS Options dialog, and select each of the following options:1.

Draw Trajectory in 2D as it is Calculated

Draw Trajectory in 3D as it is Calculated

Update Animation Time for all Objects

Delete any existing segments in the MCS except the End segment (which cannot be removed).3.

Add a Target Sequence as the first MCS segment. Click + symbol to the left of the Target Sequence and nest the following

segments within it: a Launch segment, a Propagate segment, a Maneuver segment, and two more Propagate segments.

4.

Select the Launch segment and change its Epoch to 1 Jan 1993 00:00:00.00.6.


4 di 14 12/01/2011 01:31

Select the first Propagate segment. Change its name to Coast, and change its color if necessary for clarity. Set the Trip

value for the (default) Duration stopping condition to 45 min (2700 sec).

7.

Tip: In selecting a color for this and other MCS segments, make sure that the color you choose will show up

well on the 2D and 3D backgrounds.

Select the Maneuver segment, and rename it TransLunarInjection. Verify that the Maneuver Type is Impulsive, and change

the Attitude Control to Thrust Vector.

9.

Select the second Propagate segment, and rename it ToSwingBy. Select a color that contrasts with the color selected for

the Coast segment. Change the Propagator to CisLunar. Under Stopping Conditions, click Insert..., and select R

Magnitude. Set its Trip value to 300000 (300 thousand) km. Select the other stopping condition (Duration) and click

Remove.

10.

Select the final Propagate segment, rename it ToPeriselene, and select a color that contrasts with the colors selected for

the Coast and ToSwingBy segments. Change the Propagator to CisLunar. Set the Trip value for the Duration Stopping

Condition to 10 days (864000 sec), and add two further Stopping Conditions:

11.

Altitude, with 0.0 as the Trip value and Moon as the Central Body, and

Periapsis, with Moon as the Central Body.

Trans-Lunar Injection: First Guess

You are now ready to perform an impulsive maneuver that will send the lunar probe near the Moon. This trajectory is a good first

guess to use in running the targeter to calculate the correct launch time and the correct coast time in the parking orbit.

Select the TransLunarInjection maneuver, and enter 3.15 km/sec for the Cartesian X (Velocity) direction of the Thrust

Vector.

1.

Click to run the MCS.2.

Note: When the run button has this appearance (as it does by default), it is set to run the entire MCS, not only

the segments that have changed. You will be using this setting throughout the exercise.

Animate the scenario and watch as the lunar probe approaches the vicinity of the Moon:4.

Tip: Here and elsewhere, 2D and 3D views are shown zoomed and rotated as necessary to emphasize the point that

is being made.


5 di 14 12/01/2011 01:31

Setting Up the Targeter to Calculate Launch and Coast Times

It is now time to target the Moon. To achieve that, you will use the launch epoch and the coast time as control variables (or

simply 'controls'). Astrogator will calculate new values that meet a set of constraints (or 'goals'). Here you will use Delta Right Asc

and Delta Declination as constraints. The constraints are the targeted differences in the right ascension and declination angles

between the spacecraft and the selected central body with respect to its parent body.

Select the Launch segment, and set Launch Epoch as a control variable by checking the appropriate target symbol.1.

Select the Coast segment, and set Trip value as a control variable.2.

Select the ToPeriselene segment, and click Results.... In the Results dialog, open the MultiBody folder, select Delta Right

Asc and click the right arrow button to assign it as a constraint. Assign Delta Declination as a constraint in the same way. In

the Component Details area, verify that the Moon is the CentralBody for both components.

Tip: When you select an assigned component in the upper part of the Results dialog, the details for that

component are displayed in the lower part.

3.

Select the Target Sequence segment. In the Profiles area, change the Name to Delta RA and Dec. Click Properties.... The

dialog that appears lists the controls and constraints that you selected.

4.

In the Control Parameters area, select Launch.Epoch, set Perturbation to 1 min, and set Max. Step to 1 hr. Then select

...Duration.TripValue, verify that Perturbation is set to 1 min, and set Max. Step to 5 min.

5.

In the Equality Constraints area, verify that the Desired Value for Delta Declination and Delta Right Asc is set to 0 deg.6.

Check all of the Use options, since you are using all of the controls and constraints.7.

Running the Targeter

By default, the Action field of the Target Sequence is set to 'Run nominal sequence'. If you run the MCS, the values you have set

for the various segments (e.g. 45 min Duration for the Coast segment) will be used. Here, instead, you will let the targeter

calculate new values to help achieve your goal of reaching the Moon.

Select the Target Sequence, and set the Action to 'Run active profiles ONCE'.1.

Run the MCS.2.

In the Target Sequence dialog that appears, note that targeting did not converge -- i.e. did not achieve the constraints that

you set -- and that the achieved values are displayed, together with the differences between them and the desired values

for the constraints.

3.

Set the Action to 'Run active profiles', and run the MCS again.4.

The targeter will run through several iterations and, after a short time, will converge on a solution that meets your

constraints within the specified tolerances. The Target Sequence dialog will indicate the number of iterations that were

required and, again, the differences (now small enough to be acceptable) between the achieved and desired values for the

constraints. It will also show the new values calculated for the control variables (launch epoch and coast time).

5.

Return to the Target Sequence and click Apply Changes to apply the new values to the initial state. Then change the

Action back to 'Run nominal sequence', and run the MCS again.

6.


6 di 14 12/01/2011 01:31

Look at the Launch and Coast segments and note the new values for the control variables: around 31 Dec 1992 21:33 UTCG

for the Launch Epoch, and around 3188 sec for the Duration Trip value of the Coast segment.

8.

Targeting on the B-Plane

Now that the right direction has been found for the transfer trajectory, you will use b-plane targeting -- specifically, the dot

products of the B-vector with the R and T unit vectors -- to adjust your first guess burn to capture in the desired final orbit.

Assume that you want to capture around the Moon in an orbit with a 90 degree inclination.

Setting up the Targeter to Target on the B-Plane

Select the Target Sequence, click the current profile (Delta RA and Dec), and click Make Copy to duplicate the profile.

Rename the new profile B-Plane Targeting.

1.

Set the Mode of the Delta RA and Dec profile to Not Active.2.

Select the ToPeriselene segment, click Results..., and assign Epoch as a constraint. Open the MultiBody folder and assign

BDotT and BDotR (i.e. the dot products mentioned above) as constraints. Verify that Moon is selected as the TargetBody for

the BDotT and BDotR components.

3.

Select the TransLunarInjection maneuver segment and set X(Velocity) as a control variable by checking its target icon.4.

Select the Target Sequence, click the B-Plane Targeting profile, and click Properties.... Check the Use option for

Cartesian.X (for the maneuver segment), and verify that those for the other two Control Parameters remain checked. In

the Equality Constraints area, uncheck the Use options for Delta Right Asc and Delta Declination, and check those for

BDotR, BDotT, and Epoch. For BDotR set the desired value to 5000 km; for BDotT leave the desired value at 0 km. Set the

desired value for Epoch to 4 Jan 1993 00:00:00.00 UTCG.

5.

BDotT is targeted to 0 km and BDotR is targeted to a non-zero value to generate a polar orbit. BDotR is targeted to 5000 km to


7 di 14 12/01/2011 01:31

avoid having the orbit intersect the Moon, which has a radius of approximately 1738 km.

Drawing the B-Plane

You will now create a b-plane template, add a b-plane to the spacecraft, and specify which MCS segment will add points to the

b-plane.

Right-click the scenario in the Object Browser, and select B-Plane Template from the Scenario Tools menu. In the B-Plane

Template dialog, click Add. Change the Name to Lunar B-Plane, change the Central Body to Moon, and verify that the

Reference Vector is Moon Orbit Normal.

1.

Open the 3D Graphics - B-Plane page for the satellite. Click Add... to display a dialog that lets you define a b-plane on the

basis of a selected template. Here, there is only one template (the one you just created), which is already selected.

Rename the new b-plane Lunar B-Plane and add it to the satellite.

3.


8 di 14 12/01/2011 01:31

Return to the satellite's Orbit page, double-click the ToPeriselene segment to open its Properties dialog, check Lunar_B-

Plane, and click Apply Final State to B-Planes Now. This sets the targeter to add points to the b-plane automatically.

5.

Now take a look at the Moon-centered 3D Graphics window:7.


9 di 14 12/01/2011 01:31

Running the Targeter to Achieve B-Plane Parameters

Return to the Target Sequence, and change the Action to 'Run Active Profiles ONCE'.1.

Run the MCS. Targeting will not converge.2.

In the Moon-centered 3D Graphics window, you can see the achieved point on the b-plane, as well as the Target point

defined by the desired values of BDotR and BDotT.

3.


10 di 14 12/01/2011 01:31

Change the Action of the targeter to 'Run active profiles', and run the MCS again.5.

In the Target Sequence dialog, note that targeting has converged and that new values have been calculated for the control

variables: a Launch Epoch of about 31 Dec 1992 22:09 UTCG, and a Coast Duration of about 3106 seconds.

6.

In the Moon-centered 3D Graphics window, you will see that new points have been added to the b-plane.7.

Click Apply Changes, change the Action to 'Run nominal sequence', and run the MCS again.8.

Note: It is important to remember that the B vector ends at the point where the asymptote pierces the plane, not

where the trajectory does. Think of the asymptote as the trajectory that the spacecraft would follow if the central

body had no gravity. As a result, the trajectory is always closer to the central body than the B vector, as is the case

in the above illustration.

Reaching Periselene

Assume that you want to capture around the Moon in a 90-degree inclined orbit with an altitude of 100 km. In order to measure

inclination at the Moon, you need to create a new coordinate system based on the Moon's North Pole. You will use the Vector

Geometry Tool for this purpose:

Targeting Altitude and Inclination


11 di 14 12/01/2011 01:31

Select the scenario in the Object Browser, and click in the toolbar to launch the Vector Geometry Tool.1.

In the Vector Geometry Tool, select Moon (the Moon central body folder, not the planet Moon you created) in the

Components area.

2.

Click to create new axes.4.

In the Add Axes dialog, set the Type to Aligned and Constrained. For the Aligned Vector, verify that the Z component is set

to 1 and the other components are set to 0. For the Constrained Vector, the X component should be set to 1 and the other

components should be set to 0.

5.

In the Aligned Vector area, click Select... under Reference Vector. In the Select Reference Vector dialog, in the

components listed under Moon, select Angular Velocity. Using the same method, select Moon VernalEquinox as the

Reference Vector for the Constrained Vector.

6.

Name the new axes True Moon Equator.7.

Now, click to create a new coordinate system.8.

In the Add System dialog, verify that Type is set to Assembled, and that Origin Point is set to Moon Center. For Reference

Axes, select the axes that you created (True Moon Equator). Name the new system True Lunar Equatorial.

9.

Return to the Orbit page for LunarProbe and select the Target Sequence.10.

Duplicate the B-Plane Targeting profile to create a new one named Altitude and Inclination. Make certain that this is the

only active profile by setting the Mode for the B-Plane Targeting profile (and, if necessary, the Delta RA and Dec profile) to

'Not Active'.

11.

Select the ToPeriselene segment, and click Results.... Open the Geodetic folder, assign Altitude as a constraint, and set its

CentralBody to Moon. Open the Keplerian Elements folder, assign Inclination as a constraint, and set its CoordSystem to

Moon True Lunar Equatorial, i.e. the coordinate system that you created.

12.

Return to the Target Sequence, select the Altitude and Inclination profile, and click Properties.... Make certain that the

Use options for all three Control Parameters are checked. Under Equality Constraints, the Use options for Altitude, Epoch

and Inclination should be checked, and all others should be unchecked.

13.

Select Altitude and set its Desired Value to 100 km. Select Inclination and set its Desired Value to 90 deg. The Desired

Value for Epoch should remain at 4 Jan 1993 00:00:00.00 UTCG.

14.

Change the targeter Action to 'Run active profiles', and run the MCS.15.

Click Apply Changes, set the Action to 'Run nominal sequence', and run The MCS again.16.

Approaching the Moon

You have reached periselene, but unless you perform some kind of maneuver, the spacecraft will swing by the Moon. Before you

add the Lunar Orbit Insertion sequence, observe the effects of the Moon's gravity field.

Insert a new Propagate segment at the end of the MCS (outside the Target Sequence). Assign it a color that contrasts with

those of the other Propagate segments, and name it Prop3Days.

1.

Change the Propagator to Lunar (In the Previous Versions folder) and the Trip value for Duration to 3 days (259200 sec).3.

To un-clutter the display in the Moon-centered 3D Graphics window, select the Moon in the Object Browser, open its 3D

Graphics - Attributes page, uncheck the 'Inherit from 2D Planet Graphics' option, and verify that all display options are

4.


12 di 14 12/01/2011 01:31

unchecked. Then open the B-Plane page for the satellite and uncheck the Show option.

Run the MCS.6.

Lunar Orbit Insertion

You will now perform an impulsive maneuver to capture around the Moon, circularizing the orbit while maintaining its 90 degree

inclination.

Insert a new Target Sequence before the final Propagate segment (Prop3Days). Nest a Maneuver in the new Target

Sequence and name it LOI.

1.

Select the LOI segment, leave the maneuver type at Impulsive, change the Attitude Control to Thrust Vector, and change

the Thrust Axes to VNC(Moon).

3.

Select the Cartesian X (Velocity) component as a control variable, since you will need to do a burn in a direction opposite to

Moon-centered velocity to slow down and capture into a lunar orbit.

4.

With the LOI segment still selected, click Results..., open the Keplerian Elements folder, assign Eccentricity as a

constraint, and change its CentralBody to Moon.

5.


13 di 14 12/01/2011 01:31

Select the second Target Sequence, and click Properties... in the Profiles area. Check the Use options for the Control

Parameter (Cartesian.X) and the Equality Constraint (Eccentricity). Leave the Desired Value for Eccentricity at 0, since you

want to circularize the orbit.

6.

Change the targeter Action to 'Run active profiles', and run the MCS.7.

When the targeter converges, the Target Sequence dialog will indicate that a near-zero value for eccentricity has been

achieved. Now click Apply Changes, change the Action to 'Run nominal sequence', and run the MCS again.

8.

If you rotate the Moon-centered 3D view, you can confirm visually what you learned from the Target Sequence dialog: the

orbit is substantially circular.

9.

You can also confirm the value of eccentricity and other targeted orbital elements by running a Summary report. For example,

double-click the LOI segment to display its Properties dialog, and change the Coord. System to the one you created: True Lunar

Equatorial. Then click and study the report that is generated. Among other things, you will find that the targeted values for

eccentricity (0), inclination (90 deg), and altitude (100 km - look under Selenodetic Parameters) were achieved within tolerance.


14 di 14 12/01/2011 01:31

Documents

Exercise - Moon Mission