Exchange Modul Install

8/9/2019 Exchange Modul Install

1/23

Legato NetWorkerModule for

MicrosoftExchange Server

Installation Guide

Release 3.0

Windows

2000Version


2/23

2001, Legato Systems, Inc. All rights reserved.

Legato, the Legato logo, Legato NetWorker, ClientPak, Octopus, and SmartMedia are registered trademarks; and Celestra, Co-StandbyServer, eCluster,GEMS, SnapShotServer, and StandbyServer are trademarks of Legato Systems, Inc. in the United States and/or other countries.

All other trademarks are the trademarks of their respective owners.

Legato NetWorker Module for Microsoft Exchange Server Installation Guide, Release 3.0

February 2001

e6-1463-01


3/23

THIS PRODUCT CONTAINS CERTAIN COMPUTER PROGRAMS AND OTHER PROPRIETARY MATERIAL, THE USE OF WHICH IS SUBJECT TOTHIS END-USER LICENSE AGREEMENT (THE "AGREEMENT"). DO NOT PROCEED WITH THE INSTALLATION OF THIS PRODUCT UNTIL YOU(LATER DEFINED AS LICENSEE) HAVE READ THIS AGREEMENT AND AGREE TO BE BOUND BY AND BECOME A PARTY TO THIS AGREEMENT.BY PROCEEDING WITH THE INSTALLATION OF THIS PRODUCT (OR AUTHORIZING ANY OTHER PERSON TO DO SO), YOU AND YOURCOMPANY ACCEPT THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, YOU MAY EXIT THE INSTALLATIONPROCESS AND RETURN THIS PRODUCT, ALL MEDIA AND DOCUMENTATION, AND PROOF OF PAYMENT, TO THE PLACE YOU OBTAINEDTHEM FOR A FULL REFUND WITHIN TEN (10) DAYS OF FIRST ACQUIRING THIS PRODUCT. WRITTEN APPROVAL IS NOT A PREREQUISITETO THE VALIDITY OR ENFORCEABILITY OF THIS AGREEMENT AND NO SOLICITATION OF ANY SUCH WRITTEN APPROVAL BY OR ONBEHALF OF LEGATO SHALL BE CONSTRUED AS AN INFERENCE TO THE CONTRARY. IF YOU HAVE ORDERED THIS PRODUCT, LEGATOSACCEPTANCE IS EXPRESSLY CONDITIONAL ON YOUR ASSENT TO THESE TERMS TO THE EXCLUSION OF ALL OTHER TERMS; IF THESETERMS ARE CONSIDERED AN OFFER BY LEGATO, ACCEPTANCE IS EXPRESSLY LIMITED TO THESE TERMS.

1. DEFINITIONS

1.1 Authorization Code: means the code provided to Licensee by Legatofor permanent authorization to use the Software. The Authorization Codeis provided to Licensee once the Enabler Code is registered with Legato.

1.2 Documentation: means any user reference materials on any media,provided by Legato for use with the Software.

1.3 Enabler Code: means the code provided by Legato for activation of theSoftware.

1.4 Licensee: means the person or entity acquiring this License or forwhom this License was acquired.

1.5 Software means the object code copy of the software program providedto You in association with this Agreement, together with the associatedoriginal electronic media and all accompanying manuals and otherdocumentation, and together with all enhancements, upgrades, and

extensions thereto that may be provided by Legato to You from time totime.

2. OWNERSHIP AND ADMINISTRATION OF SOFTWARE

2.1 Ownership and Title. As between the parties, Legato, and its licensors,own and shall retain all right, title, and interest in and to: (i) the Softwareincluding all intellectual property rights embodied therein; (ii) all of theservice marks, trademarks, trade names, or any other designationsassociated with the Software; and (iii) all copyrights, patent rights, tradesecret rights, and other proprietary rights relating to the Software.Licensee further acknowledges and agrees that it shall have no rights withrespect to any of the foregoing rights other than the rights expressly setforth in this Agreement.

2.2 Software Activation. Legato employs Enabler Codes andAuthorization Codes that enable the use of the Software. The Software isshipped in a "Media Kit" which consists of object code software onCD-ROM and an Enabler Code for initial activation of the Software or theSoftware and Enabler Code may be delivered electronically. Once Legato

receives confirmation from Licensee that the Enabler Code is installed andis provided with the host ID information, Legato will provide theAuthorization Code to Licensee. Legato administers the generation anddistribution of Enabler and Authorization Codes, which administrationmay be modified by Legato from time to time.

2.3 Administration of Software. Legato may include on the media with theSoftware additional computer programs which are not currently licensedfor use by Licensee and to which the Enabler Code or Authorization codewill not permit access. Inclusion of such additional computer programs inno way implies a license from Legato and access or use of such programsis strictly prohibited unless Licensee procures the right to use any suchprogram and the applicable Enabler Code is provided thereto.

3. LICENSE GRANT

3.1 Grant. Legato grants to Licensee a non-exclusive, nontransferable,non-sublicensable, perpetual, unless terminated in accordance with theprovisions of this Agreement, license (the "License") to (i) use the Softwareinstalled in accordance with the Documentation and only on the licensedcomputer solely for its own internal operations; and (ii) move the Softwaretemporarily in case of computer system malfunction. The License grantedunder this Agreement does not constitute a sale of the Software or anyportion or copy of it. Licensee may not use the Software on more than onecomputer system unless otherwise specifically authorized by an explicitSoftware product, or additional licenses for additional computers arepurchased. Rights not expressly granted are reserved by Legato. Wherethe Software is provided to Licensee at no charge for evaluation purposesonly, the License granted is limited to a continuous thirty (30) day period,commencing with the acceptance of this Agreement (the "EvaluationPeriod"). At the conclusion of the Evaluation Period, Licensee agrees todestroy the Software and certify its destruction to Legato, in writing,within ten (10) days, or shall return the Software to Legato or purchase aperpetual license.

3.2 Copies. Licensee may make copies of the Software provided that anysuch copy is : (i) created as an essential step in utilization of the Softwareon the licensed computer and is used in no other manner; or (ii) used forarchival purposes to back-up the licensed computers. All trademark andcopyright notices must be reproduced and included on such copies.Licensee may not make any other copies of the Software.

3.3 Restrictions on use. Licensee shall not, and shall not aid, abet, or permitany third party to: (i) decompile, disassemble, or otherwise reverseengineer or attempt to reconstruct or discover any source code orunderlying ideas or algorithms of the Software by any means whatsoever;(ii) remove any identification, copyright, or other notices from theSoftware; (iii) provide, lease, lend, use for timesharing or service bureaupurposes, or otherwise use or allow others to use the Software or anyportion thereof to or for the benefit of third parties; (iv) create a derivativework of any part of the Software; or (v) develop methods to enableunauthorized parties to use the Software. If EC law is applicable, therestrictions in Section 3.3 (i) are limited so that they prohibit such activityonly to the maximum extent such activity may be prohibited withoutviolating the EC Directive on the legal protection of computer programs.Notwithstanding the foregoing, prior to decompiling, disassembling, orotherwise reverse engineering any of the Software, Licensee shall requestLegato in writing, to provide Licensee with such information or assistanceand Licensee shall refrain from decompiling, disassembling, or otherwisereverse engineering any of the Software unless Legato cannot or has notcomplied with such request in a commercially reasonable amount of time

3.4 Purchase Orders. Nothing contained in any purchase order,acknowledgment, or invoice shall in any way modify the terms or add anyadditional terms or conditions to this Agreement.

3.5 Updates. This section applies if the Software acquired is an update tothe original Software ( the "Update"). An Update does not constitute alegally licensed copy of the Software unless purchased as an Update to aprevious version of the same Software. The Update may only be used inaccordance with the provisions of this Agreement. The Update, togetherwith the original Software, constitute one (1) legally licensed copy of the

Software.3.6 Evaluation License. This Section applies if the Software is being usedfor an initial thirty (30) day evaluation period. The license is valid only fora period of thirty (30) days from the delivery of the Software, and isdesigned to allow Licensee the right to evaluate the Software during suchperiod. In the event that Licensee desires to enter into a longer-term licenseagreement with Legato, Licensee shall obtain an appropriate Enabler andAuthorization Code in accordance with Section 2.2 above, upon paymentof applicable fees, which authorizes use of the Software after suchevaluation period, but only subject to all of the terms and conditions of thisAgreement. In the event Licensee determines not to enter into a licensingtransaction with Legato at the end of such thirty (30) day evaluationperiod, then Licensees rights under this Agreement shall terminateautomatically and Licensee shall promptly return to Legato or destroy allcopies of the Software and so certify to Legato.

4. MAINTENANCE AND SUPPORT

4.1 Legato has no obligation to provide support, maintenance, upgrades,modifications, or new releases under this Agreement. Legato may providesuch services under separate agreement.

5. LIMITED WARRANTY

5.1 Media and Documentation. Legato warrants that if the media ordocumentation are damaged or physically defective at the time of deliveryof the first copy of the Software to Licensee and if defective or damagedproduct is returned to Legato (postage prepaid) within thirty (30) daysthereafter, then Legato will provide Licensee with replacements at no cost

5.2 Software. Subject to the conditions and limitations of liability statedherein, Legato warrants for a period of thirty (30) days from the delivery ofthe first copy of the Software to Licensee that the Software, as delivered,will materially conform to Legatos then current published Documentation


4/23

for the Software. This warranty covers only problems reported to Legatoduring the warranty period.

5.3 Remedies. The remedies available to Licensee hereunder for any suchSoftware which does not perform as set out herein shall be either repair orreplacement, or, if such remedy is not practicable in Legatos opinion,refund of the license fees paid by Licensee upon a return of all copies of theSoftware to Legato. In the event of a refund this Agreement shallterminate immediately without notice.

6. TERM AND TERMINATION6.1 Term. The term of this Agreement is perpetual unless terminated inaccordance with its provisions.

6.2 Termination. Legato may terminate this Agreement, without notice,upon Licensees breach of any of the provisions hereof.

6.3 Effect of Termination. Upon termination of this Agreement, Licenseeagrees to cease all use of the Software and to return to Legato or destroythe Software and all Documentation and related materials in Licenseespossession, and so certify to Legato. Except for the License granted hereinand as expressly provided herein, the terms of this Agreement shallsurvive termination.

7. DISCLAIMER AND LIMITATIONS

7.1 Warranty Disclaimer. EXCEPT FOR THE LIMITED WARRANTYPROVIDED IN SECTION 5 ABOVE, LEGATO MAKES NOWARRANTIES WITH RESPECT TO ANY SOFTWARE AND DISCLAIMSALL STATUTORY OR IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY,FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM ACOURSE OF DEALING OR USAGE OF TRADE AND ANYWARRANTIES OF NONINFRINGEMENT. ALL SOFTWARE ISPROVIDED "AS IS" AND LEGATO DOES NOT WARRANT THAT THESOFTWARE WILL MEET ANY REQUIREMENTS OR THAT THEOPERATION OF SOFTWARE WILL BE UNINTERRUPTED OR ERRORFREE. ANY LIABILITY OF LEGATO WITH RESPECT TO THESOFTWARE OR THE PERFORMANCE THEREOF UNDER ANYWARRANTY, NEGLIGENCE, STRICT LIABILITY OR OTHER THEORYWILL BE LIMITED EXCLUSIVELY TO THE REMEDIES SPECIFIED INSECTION 5.3 ABOVE. Some jurisdictions do not allow the exclusion ofimplied warranties or limitations on how long an implied warranty maylast, so the above limitations may not be applicable. This warrantyprovides specific legal rights. Other rights vary from state to state.Licensee acknowledges and agrees that Legato is not responsible for andwill have no liability for hardware, software, or other items or servicesprovided by persons other than Legato.

8. LIMITATION OF LIABILITY

8.1 Limitation of Liability. NOTWITHSTANDING ANYTHING ELSE INTHIS AGREEMENT OR OTHERWISE, AND EXCEPT FOR BODILYINJURY, LEGATO WILL IN NO EVENT BE LIABLE OR RESPONSIBLEFOR OR OBLIGATED WITH RESPECT TO THE SUBJECT MATTER OFTHIS AGREEMENT UNDER ANY CONTRACT, NEGLIGENCE, STRICTLIABILITY, OR OTHER LEGAL CONTRACTUAL OR EQUITABLETHEORY FOR: (I) ANY INDIRECT, SPECIAL, INCIDENTAL ORCONSEQUENTIAL DAMAGES, HOWEVER CAUSED AND WHETHEROR NOT ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCHDAMAGES; OR (II) DAMAGES FOR LOST PROFITS OR LOST DATA; OR(III) COST OF PROCUREMENT OF SUBSTITUTE GOODS,TECHNOLOGY, SERVICES, OR RIGHTS; OR (IV) FOR ANY MATTERBEYOND ITS REASONABLE CONTROL. NOTWITHSTANDINGANYTHING IN THIS AGREEMENT TO THE CONTRARY OR THEFAILURE OF ESSENTIAL PURPOSE OF ANY LIMITATION OFLIABILITY OR LIMITED REMEDY, LEGATOS ENTIRE AGGREGATELIABILITY ARISING FROM OR RELATING TO THIS AGREEMENT ORTHE SUBJECT MATTER HEREOF, UNDER ANY LEGAL THEORY

(WHETHER IN CONTRACT, TORT, INDEMNITY OR OTHERWISE)SHALL BE LIMITED TO THE AMOUNTS RECEIVED BY LEGATO FORTHE SOFTWARE DURING THE SIX (6) MONTH PERIOD PRIOR TOTHE DATE THE CLAIM AROSE FOR THE PARTICULAR LEGATOSOFTWARE THAT CAUSED THE LIABILITY.

9. MISCELLANEOUS

9.1 Governing Law. This Agreement shall be governed by the laws of theState of California, as applied to agreements entered into and to beperformed entirely within California between California residents,without regard to the principles of conflict of laws or the United NationsConvention on Contracts for the International Sale of Goods.

9.2 Government Restricted Rights. This provision applies to Softwareacquired directly or indirectly by or on behalf of any government. The

Software is a commercial software product, licensed on the open market atmarket prices, and was developed entirely at private expense and withoutthe use of any government funds. Any use, modification, reproduction,release, performance, display, or disclosure of the Software by anygovernment shall be governed solely by the terms of this Agreement andshall be prohibited except to the extent expressly permitted by the terms ofthis Agreement, and no license to the Software is granted to anygovernment requiring different terms.

9.3 U.S. Government Users. As defined in FAR section 2.101, DFAR section252.227-7014(a)(1), DFAR section 252.227-7014(a)(5), or otherwise, allsoftware and accompanying documentation provided in connection withthis Agreement are "commercial items," "commercial computer software"and/or "commercial computer software documentation." Consistent withDFAR section 227.7202 and FAR section 12.212, any use, modification,reproduction, release, performance, display, disclosure, or distributionthereof by or for the U.S. Government shall be governed solely by the termsof this Agreement and shall be prohibited except to the extent expresslypermitted by the terms of this Agreement. Licensee will ensure that eachcopy used or possessed by or for the government is labeled to reflect the

foregoing.9.4 Export and Import Controls. Regardless of any disclosure made byLicensee to Legato of an ultimate destination of the Products, Licensee willnot directly or indirectly export or transfer any portion of the Software, orany system containing a portion of the Software, to anyone outside theUnited States (including further export if Licensee took delivery outsidethe U.S.) without first complying with any export or import controls thatmay be imposed on the Software by the U.S. Government or any countryor organization of nations within whose jurisdiction Licensee operates ordoes business. Licensee shall at all times strictly comply with all such lawsregulations, and orders, and agrees to commit no act which, directly orindirectly, would violate any such law, regulation or order.

9.5 Assignment. This Agreement may not be assigned or transferred byLicensee without the prior written consent of Legato which shall not beunreasonably withheld. Legato may assign or otherwise transfer any or alof its rights and obligations under this Agreement upon notice to Licensee

9.6 Sole Remedy and Allocation of Risk. Licensees sole and exclusive

remedy is set forth in this Agreement. This Agreement defines a mutuallyagreed-upon allocation of risk, and the License price reflects suchallocation of risk.

9.7 Equitable Relief. The parties agree that a breach of this Agreementadversely affecting Legatos intellectual property rights in the Softwaremay cause irreparable injury to Legato for which monetary damages maynot be an adequate remedy and Legato shall be entitled to equitable reliefin addition to any remedies it may have hereunder or at law.

9.8 No Waiver. Failure by either party to enforce any provision of thisAgreement will not be deemed a waiver of future enforcement of that orany other provision, nor will any single or partial exercise of any right orpower hereunder preclude further exercise of any other right hereunder.

9.9 Severability. If for any reason a court of competent jurisdiction findsany provision of this Agreement, or portion thereof, to be unenforceable,that provision of the Agreement will be enforced to the maximum extentpermissible so as to effect the intent of the parties, and the remainder of thisAgreement will continue in full force and effect.

10. ENTIRE AGREEMENT

10.1 This Agreement sets forth the entire understanding and agreementbetween the parties and may be amended only in a writing signed byauthorized representatives of both parties. No vendor, distributor, dealerretailer, sales person, or other person is authorized by Legato to modifythis Agreement or to make any warranty, representation, or promise whichis different than, or in addition to, the warranties, representations, orpromises made in this Agreement.


5/23

Legato NetWorker Module for Microsoft Exchange Server

Installation Guide v

Contents

Preface....................................................................................................................... 7.

Product Documentation .................................................................................................................. 7.

Conventions.................................................................................................................................... 7.

Information and Services................................................................................................................ 8.

General Information ................................................................................................................. 8.

Technical Support .................................................................................................................... 9.

Customer Service..................................................................................................................... 9.

Customer Feedback ....................................................................................................................... 9.

Chapter 1: Introduction..........................................................................................10.

NetWorker Software ..................................................................................................................... 10.

NetWorker Module for Microsoft Exchange Server Software ....................................................... 11.

New Features in this Release....................................................................................................... 11.

Chapter 2: Installation............................................................................................ 12.

Installation Roadmap.................................................................................................................... 12.

System Requirements............................................................................................................ 13.

Privileges Required for Installation......................................................................................... 14.

Installing NetWorker Module for Microsoft Exchange Server ....................................................... 14.

How to Start the Installation from a Local CD-ROM............................................................... 14.

How to Start the Installation from a Remote CD-ROM Drive ................................................. 15.

How to Start the Installation from a Downloaded File ............................................................ 15.

How to Complete the Installation ........................................................................................... 15.

Possible Installation Problems ............................................................................................... 16.

Registration Name........................................................................................................... 16.

Setup Initialization Error .................................................................................................. 16.

Using Microsoft Systems Management Server (SMS) for Installation ................................... 16.

How to Create Application Source Directories....................................................................... 17.

How to Create the SMS Installation Package ........................................................................ 17.

How to Create the Installation or Uninstallation Job .............................................................. 18.

Installing NetWorker Module Software in a Microsoft Cluster ...................................................... 19.

Enabling and Registering Software .............................................................................................. 20 .

Enabler Codes ....................................................................................................................... 20.


6/23

Contents

Legato NetWorker Module for Microsoft Exchange Server

Installation Guide vi

Temporary Enablers ........................................................................................................ 20.

Enter the Temporary Enabler .......................................................................................... 20.

Obtain a Permanent Enabler ........................................................................................... 21.

How to Obtain an Authorization Code.................................................................................... 21.

How to Complete the Registration Form.......................................................................... 21.

How to Print and Send the Registration Form ................................................................. 22.

How to Enter the Authorization Code .............................................................................. 22.

Web Registration and Authorization....................................................................................... 23.

Removing the NetWorker Module Software ................................................................................. 23 .


7/23

Legato NetWorker for Microsoft Exchange Server

Installation Guide 7

Preface

The Legato NetWorkerModule for MicrosoftExchange Server Installation Guide, Release3.0, provides instructions on how to install the Legato NetWorker for MicrosoftExchange Server software.

After you install the NetWorker Modulesoftware, refer to the Legato NetWorker Modulefor Microsoft Exchange Server Administrators Guideand the programs online help fordetailed instructions on how to configure, administer, and use the NetWorker Modulesoftware.

The information in this guide is intended for system administrators who areresponsible for installing software and maintaining the servers and clients on anetwork. Operators who monitor the daily backups may also find this manual useful.

Product Documentation

Legato offers an extensive archive of product documentation at its web sitewww.legato.com. Most of the documents are in AdobeAcrobatPortable DocumentFormat (PDF), and can be viewed by downloading and installing the Adobe AcrobatReader. The Reader is available in the/viewers/acroreaddirectory on the LegatoDocumentation Suite CD-ROM, or directly from Adobe at www.adobe.com. To installand use the Reader on the platform of your choice, refer to the instructions in theCD-ROMs/viewers/acroread/readme.txtfile or at the Adobe web site.

Conventions

This document uses the following typographic conventions and symbols to makeinformation easier to access and understand.

Convention Indicates Example

boldface Names of DOS or UNIX linecommands, daemons, options,programs, or scripts

The nsradmincommand starts thecommand line version of the administrationprogram.

italic in text Pathnames, filenames, computernames, new terms defined in theGlossary or within the chapter,or emphasized words

Displayed messages are also written to/nsr/logs/daemon.log.


8/23


Installation Guide

Preface

8

Information and Services

Legato offers a variety of methods, including electronic, telephone, and fax support, foryou to obtain company, product, and technical information.

General Information

The Legato web site provides most of the information that you might need. If you wanttechnical bulletins and binary patches, you can also access the Legato FTP site. If youhave specific sales or training needs, e-mail or call Legato.

italic in command line A variable that you need toprovide in the command line

nwadmin -s server-name

fixed-width Examples and informationdisplayed on the screen media waiting: recover waiting for8mm 5GB tape volume name

fixed-width,

boldface

Commands and options thatyou must type exactly as shown

nsr_shutdown -a

Menu_Name>Command>Command

A path or an order to follow formaking selections in the GUI

Volume>Change Mode>Appendable

Important: Information that you must readand follow to ensure successfulbackup and recovery of yourdata

Legato Service or Resourcea

a. For detailed information about our services, support policies, and software subscriptions, refer to theLegato Customer Service and Support Guideincluded in the media kit.

Technical

Bulletins

Binary

Patches

Company &Product

Information

Training

Programs

www.legato.com Yes Yes Yes Yes

ftp.legato.com(log in as anonymous) Yes Yes

Legato Inside Sales,(408) 530-3000 [email protected]

Yes

Legato Education Services,(408) 530-3099 [email protected]

Yes

Convention Indicates Example

Important: You must install the NetWorkerModule software in the same directorywhere you installed the NetWorker clientbinaries.


9/23


Installation Guide

Preface

9

Technical Support

The Support section of the Legato web site provides contact information, softwarepatches, technical documentation, and information about available support programs.

If you have an active support agreement, you may access TechDialog, the Legato

integrated product knowledge base. You may also contact Legato TechnicalSupport for help with Legato software issues.

If you do not have an active support agreement, contact LegatoCare to purchaseannual Software Update Subscriptions, Legato Technical Support services, orper-update/per-incident support.

Customer Service

Legato provides a variety of ways for you to contact Customer Service. To register yourLegato products, go to the Legato licensing web site. To ask questions about licensing,to transfer licenses, or to learn the status of your order, contact Legato using one of thefollowing methods.

Customer Feedback

Legato welcomes your comments and suggestions about software features, theinstallation procedure, and documentation. Please send any suggestions andcomments [email protected]. You will receive a notice confirming receipt of youre-mail. Although we cannot respond personally to every request, we consider all yourcomments and suggestions during product design.

Help us improve our documentation and be eligible to win a prize by completing abrief survey. Visit the Legato web site at www.legato.com, go to the Manuals page, andthen look for the link to the Legato Documentation Survey.

Customer Service Contact

Legato licensing web site http://license.legato.com

Telephone number (650) 812-6063 (option 3)

Fax number (650) 812-6220

E-mail [email protected]

E-mail for order status [email protected]


10/23



Chapter 1: Introduction

This chapter provides brief descriptions of the NetWorker and NetWorker Module forMicrosoft Exchange Server (formerly BusinesSuite Module) software. It contains thefollowing sections:

NetWorker Software on page 10

NetWorker Module for Microsoft Exchange Server Software on page 11 New Features in this Release on page 11

NetWorker Software

Legato NetWorker software is a network data storage management solution thatprotects and helps manage data across an entire network. NetWorker simplifies thestorage management process and reduces the administrative burden by automatingand centralizing data storage operations. As a network expands or as the amount ofdata grows, NetWorker software provides the capacity and performance to protect it.

With NetWorker, you can:

Perform automated lights out backups during non-peak hours.

Administer, configure, monitor, and control NetWorker software functions fromany system on a network.

Centralize and automate data management tasks.

Increase backup performance by simultaneously sending more than one savestream to the same device.

Optimize performance using parallel save streams to a single device, or tomultiple devices or storage nodes.

NetWorker client/server technology uses the network protocol Remote Procedure Call(RPC) to back up data. The NetWorker server software consists of several server-sideservices and programs that oversee backup and recover processes. The NetWorker

client software consists of client-side services and user interface programs.

The NetWorker server:

Oversees backup and recovery processes.

Maintains client configuration files.

Maintains an online client file index.

Maintains an online media database.


11/23


Installation Guide

Chapter 1: Introduction

11

NetWorker Module for Microsoft Exchange Server Software

NetWorker Module for Microsoft Exchange Server (formerly BusinesSuite Module forMicrosoft Exchange Server) is an add-on module for the NetWorker software. Itintegrates backup and restore procedures for Exchange Server databases with the

network-wide data protection of the NetWorker software . Together, these twoproducts provide reliable, high-performance data protection for Exchange Serverdatabases and mailboxes.

New Features in this Release

New features in this release include:

Support for Microsoft Exchange 2000 Server(Intelonly) and Windows2000

Recovery of storage groups and databases from Exchange Server InformationStore (IS) backups

Parallel backup and recovery of multiple storage groups and databases

Automatic mount and dismount of IS databases

Backup and restore of private mailboxes

Backup and recovery of Key Management Server (KMS) and Site ReplicationServer (SRS)

Disaster recovery for Microsoft Exchange 2000 Server

An enhanced GUI that supports Exchange Server, Key Management Server andSite Replication Server.

Improved support for MSCS clusters.

Support for multiple simultaneous backup and recover processes in Windows

Performance Monitor.


12/23



Chapter 2: Installation

This chapter describes how to install the Legato NetWorker Module software oncomputers using the Windows 2000 operating system.

Installation Roadmap

The following list is a roadmap to follow when installing NetWorker Module softwareon each Exchange Server that requires backup and recovery services. Read through theroadmap and the referenced sections before installing the NetWorker Modulesoftware.

Before you install the NetWorker Module software:

1. Review System Requirements on page 13.

2. Verify that you have the required user privileges. For details, see PrivilegesRequired for Installation on page 14.

3. Install the NetWorker Module for Microsoft Exchange Server software. For details,see Installing NetWorker Module for Microsoft Exchange Server on page 14.

4. Enable and register NetWorker Module for Microsoft Exchange Server. For details,see Enabling and Registering Software on page 20.

5. Configure a client resource on the NetWorker server for each client computer andvirtual server. For details, refer to the NetWorker Modulefor Microsoft ExchangeServer Administrators Guide.


13/23


Installation Guide


13

System Requirements

To install the NetWorker Module software, the following requirements must be met:

Exchange Server System Management Components installed; (when you installExchange Server, you must select System Management Components to provide

support for backup and recovery)

Windows 2000 Server, Advanced Server, or Data Center

Latest Windows 2000 Service Pack

NetWorker 5.7 or later for Windows 2000/NT client software

Approximately 9 MB of available space on the drive where you installed theNetWorker client software. The installed software requires 4 MB of disk space.Temporary files created during installation require additional space. After theinstallation is complete, the temporary files are deleted.

A drive with up to 1 MB of free space on the computer running Exchange 2000Server, for the Exchange Server online documentation files.

Important: If a previous version of NetWorker Module for Microsoft Exchange Serveris installed on the Exchange Server, remove it before you install the new NetWorkerModule software. For instructions, see Removing the NetWorker Module Softwareon page 23.

Table 1shows operating system and product compatibility for each of the componentsrequired for the NetWorker Module software installation.

Table 1. Operating System and Product Compatibility

Product Versions Host Platform

ExchangeServerHost Operating

System

Microsoft Exchange2000 Server

Microsoft Exchange 2000Server or Microsoft Exchange2000 Server, Enterprise Edition

Windows 2000(Intelonly)

Windows 2000,Service Pack(SP) 1

NetWorker Client forWindows

5.7 and later Windows 2000,(Intelonly)

Windows 2000SP 1

NetWorker Server 5.1 and later Windows NT,AIX, HP-UX,

Compaq Tru64UNIX,SGIIRIX, SUNSPARC

Refer to theLegato Software

CompatibilityGuideavailablefrom the Legatoweb site atwww.legato.com.


14/23


Installation Guide


14

Privileges Required for Installation

Installing NetWorker Module requires multiple administrator or user privilegesbecause NetWorker Module software connects to both the NetWorker server and theExchange 2000 Server.

Table 2lists the privileges you need to install and configure the NetWorker Modulesoftware.

Installing NetWorker Module for Microsoft Exchange Server

This section addresses installing the NetWorker Module for Microsoft Exchange Serversoftware from various media, including:

Local CD-ROM drive

Shared network location

Downloaded file from www.legato.com

How to Start the Installation from a Local CD-ROM

To use a CD-ROM drive on the local computer to start the installation:

1. Log on to Windows, using an account with Administrator privileges.

2. Load the NetWorker Module CD-ROM in the CD-ROM drive.

3. Open the Windows Explorer and select the CD-ROM drive.

4. Continue with the instructions in How to Complete the Installation on page 15.

Table 2. Privileges Required for Installation and Configuration

Installation TasksWindows 2000Administrator Group

NetWorker ServerAdministratorAccess

Install NetWorker Module X

Create separate NetWorker volume pools forExchange Server database data and logical

log file backups (recommended)

X


15/23


Installation Guide


15

How to Start the Installation from a Remote CD-ROM Drive

To install the software from a remote CD-ROM drive:

1. Load the NetWorker Module CD-ROM in the CD-ROM drive of a Windows 2000or Windows NT computer on the network.

2. Mount the CD-ROM drive as a shared network disk volume. For detailedinstructions, refer to Microsoft documentation.

3. Log on to the computer running Exchange 2000 Server.

4. Map a drive to the shared volume (CD-ROM drive) you created on the remotesystem.

5. Continue with the instructions in How to Complete the Installation on page 15.

How to Start the Installation from a Downloaded File

To install NetWorker Module evaluation software downloaded from the Legato web

site:1. Log on as Administrator or equivalent on the Exchange 2000 Server.

2. Create a temporary directory to hold the downloaded file.

3. Move the downloaded file to the temporary directory.

4. Extract the files from the downloaded file to the temporary directory.

5. When the extraction is complete, continue with the instructions in How toComplete the Installation on page 15.

How to Complete the Installation

To complete the installation of the NetWorker Module software:1. Exit all NetWorker programs.

2. Open the Windows Explorer and navigate to the directory holding the NetWorkerModule installation files.

3. Run SETUP.EXEto open the Setup Options dialog box and begin the installation.

4. In the dialog box that appears, select Install.

5. Enable the NetWorker Module software. For detailed instructions, see Enablingand Registering Software on page 20.

The NetWorker Module setup program installs binary files in the same directory as theexisting NetWorker client, and adds the NetWorker User for Exchange Server icon to

the NetWorker Group in the Windows Start menu.


16/23


Installation Guide


16

Possible Installation Problems

Two known problems may occur during installation.

Registration Name

When you enter an enabler for the NetWorker Module for Microsoft Exchange Server,the registration name may appear as Business Suite Module for Exchange. This occursbecause the NetWorker server controls the way the NetWorker Module softwaredisplays its product name.

If you are using the NetWorker 6.0 software on your NetWorker server, the registrationname for the Module software that is displayed is NetWorker Modulefor MicrosoftExchange Server. If you are using the NetWorker 5.7 software on your NetWorker server,the registration name for the Module software that is displayed is BusinesSuite Module

for Microsoft Exchange Server.The NetWorker Module software works properly,regardless of which product name is displayed.

Setup Initialization Error

During installation you may see this error message:

Insufficient memory to run setup

This message occurs on systems that have a large amount of memory and also have the/3GB switch in their boot.inifiles. If you encounter this error, set the default directoryto the Exchange setup\i386. Then run setup.exewith the -zoption:

setup -z

For detailed instructions on using commands and switches, refer to the LegatoNetWorker Modulefor Microsoft Exchange Server Administrators Guide, Release 3.0. Fordetailed information, refer to Installshield Knowledge Base Article #Q101828, available

at www.installshield.com .

Using Microsoft Systems Management Server (SMS) for Installation

NetWorker Module software supports the Microsoft Systems Management Server(SMS) installation system. You can use SMS to configure your system to automaticallyinstall NetWorker Module over an entire network.

For best results:

1. Set up the Exchange 2000 Server and SMS software before you install theNetWorker Module software. For detailed instructions, refer to the Microsoft SMSdocumentation.

2. Do not configure the SMS server on a NetWorker server host. You can, however,configure the SMS server on a NetWorker client host.

3. Test the SMS software before you install NetWorker Module software.


17/23


Installation Guide


17

NetWorker Module software installation under SMS consists of three main procedures:

Creating the NetWorker Module software application source directory ordirectories.

Creating the SMS installation package.

Creating the job to install or uninstall the NetWorker Module software on theclient computer(s).

These procedures are described in the following sections.

How to Create Application Source Directories

To create the NetWorker Module software application source directory:

1. Create a shared directory on one of the SMS site server's local disks. For example,for Intel_shared_dir_name,create a directory called nwme30i

2. Copy all files from appropriate file on the NetWorker Module CD-ROM (i.e.,\MSEXCHNG\1386\NETWORKR) to the corresponding shared directory you

created for those files on the SMS site server disk.

How to Create the SMS Installation Package

Package Command Manager (PCM) can run under Windows in the foreground, or inthe background as a service.

To run background (unattended) installations, you must have PCM running as aWindows service on the target Windows client computer.

For more information about using PCM, refer to Microsoft knowledge base articleQ166765, Deploying Packages Successfully with the PCM Service.

To create the SMS installation package:

1. Use the SMS Administrator program to open the Packages window at the SMS siteserver.

2. From the File menu, select New to open the Package Properties dialog box.

3. Click Import to open the File Browser dialog box.

4. To configure the NetWorker Module software installation as an automated,background process requiring no user input, select Nwmsxchi.pdffrom theIntel_shared_dir_name directory on the SMS site server.

5. Click OK to close the File Browser dialog box and return to the Package Propertiesdialog box.

6. Click Workstations to open the Setup Package for Workstations dialog box.

7. In the Source Directory field, enter your server name and shared directory name(s)as \ \ server_name\ Intel_shared_di r_name, where server_nameis the name of theSMS site server.

8. Click Close to return to the Package Properties dialog box.

9. Click OK to close the Package Properties dialog box.

The SMS installation package creation is complete.


18/23


Installation Guide


18

How to Create the Installation or Uninstallation Job

To create a job to install or uninstall NetWorker Module software :

1. Open the Packages window at the SMS site server.

2. Open the Sites window.3. From the Packages window, select the NetWorker Module software package. Drag

this package to a computer in the Sites window. This opens the Job Details dialogbox.

4. In the Send Phase section of the Job Details dialog box, click Even If PreviouslySent.

5. In the Run Phase section of the Job Details dialog box, select a setup option (eitherInstall or Uninstall) from the menu under Run Workstation Command.

6. If you are using the PCM service (on Windows NT clients) to perform backgroundinstallations, specify the job runtime in the Mandatory After (notthe OfferAfter) portion of the Run Phase section of the Job Details dialog box.

7. Click OK in the Job Details dialog box to close the dialog box. SMS then displaysthe Job Properties dialog box.

For further details on configuring the job in the Job Details dialog box, refer toMicrosoft SMS documentation.


19/23


Installation Guide


19

Installing NetWorker Module Software in a Microsoft Cluster

The procedures in this section are for using NetWorker Module within a Microsoftcluster environment.

Important: Since the NetWorker Module software is automatically installed in thesame path as the NetWorker filesystem client, it is also installed on the local disk ofeach node in the cluster. Do not install the NetWorker filesystem client or theNetWorker Module software on a cluster disk.

To install and configure the NetWorker client software and the NetWorker Modulesoftware in a Microsoft cluster:

1. Install the NetWorker client software and NetWorker Module for MicrosoftExchange Server software on the local disk of each physical node. It is best to usethe default NetWorker installation directory.

When you install the NetWorker client software, you have the opportunity to specify the

names of the NetWorker server hosts that may be used to back up the cluster.

2. Install the enabler for the NetWorker Module software on the NetWorker serverhost. For details on how to do this, see Enabling and Registering Software onpage 20.

3. The installation is complete.


20/23


Installation Guide


20

Enabling and Registering Software

This section provides information about enabling your NetWorker Module softwarefor evaluation, and after purchase.

You can use NetWorker Module for up to 30 days without entering an enabler code.This is called evaluation mode. The software is fully functional during this time. After30 days, the software does not work until you enter a temporary or permanent enablercode. Details about these codes appear in the next section.

Enabler Codes

To use NetWorker Module beyond the 30 day evaluation period, you must enter anEnabler code. There are two types of enabler codes:

Temporary enablers

Permanent enablers

Temporary Enablers

Temporary enabler codes make it possible to use the NetWorker Module software foran additional period beyond the initial evaluation mode period. For more detailedinformation, refer to the Legato NetWorker Administrators Guide for your NetWorkerserver software.

At the end of the evaluation period, the NetWorker Module software is disabled. Tocontinue using it, you must purchase an Enabler Certificate and enter an AuthorizationCode (see How to Purchase an Enabler Certificate on page 25).

Table 1 shows a temporary enabler code that you can enter to extend your evaluationtime for NetWorker Module. To obtain a temporary enabler code for NetWorkersoftware, refer to the Legato NetWorker Administrators Guidefor your NetWorker

software.

Enter the Temporary Enabler

To enter the temporary enabler code:

1. Log on to the NetWorker server as Administrator.

2. Open the NetWorker Administrator program. The program opens to the Configuretab (in the right-hand window-pane).

3. On the Configure tab, under the Manage Server heading, click the Registrationbutton. The Registration dialog box opens.

Table 3. NetWorker Module Temporary Enabler

NetWorker Server Platform Temporary Enabler

Windows 2000 or Windows NT de5b60-aa1a2d-d3dca4


21/23


Installation Guide


21

4. In the directory tree in the Registration dialog box, right-click on the NetWorkerserver for which you want to enter a temporary enabler, and select Create from thesub-menu that appears. The License Registration dialog box opens.

5. Enter the Temporary Enabler (use the one shown in Table 3 on page 20) in theLicense Registration dialog box, and click OK.

Important: If the same evaluation enabler code is entered on more than one computeron the same network, a copy violation error occurs and the NetWorker server softwareis disabled.

Obtain a Permanent Enabler

You can purchase a permanent enabler from Legato in any of the following ways:

Contact Legato Inside Sales.

Send e-mail to [email protected].

Contact an Authorized Legato Reseller.

Legato sends a permanent Enabler Certificate to you. This certificate provides theEnabler code. You must also register the software and obtain an Authorization code.

How to Obtain an Authorization Code

After you receive your permanent enabler, you must obtain a permanent authorizationcode to continue using NetWorker Module with the privileges specified in youragreement.

To obtain the authorization code, complete a registration form and send it to LegatoCustomer Service, as described in the following procedures.

How to Complete the Registration Form

To complete the registration form:

1. In the NetWorker Administrator software, Configure tab, click Set Up Server.

2. From the Set Up Server dialog box, select the Company Information tab.

3. Complete the information text boxes in the Company Information tab and clickOK. The product serial number is on your Enabler Certificate.

4. Enter your permanent enabler code:

a. Log on to the NetWorker server as Administrator.

b. Open the Server window and provide the requested information.

c. Open the Registration window and click the Create button.

d. Enter your code in the Enabler Code field.


22/23


Installation Guide


22

How to Print and Send the Registration Form

To print and send the registration form:

1. Click Registration in the Configure tab to open the Registration window.

2. Right-click the NetWorker Module software icon. Each NetWorker Moduleproduct for which you entered an enabler code is represented by a separate icon inthe Registration window.

3. Select Edit from the pop-up menu to open the Edit Registration dialog box.

4. To print the registration form, which includes the enabler code you entered and thecompany and product information you provided earlier:

a. Select the Tabular option from the View menu.

b. Select Print from the File menu.

5. Mail, fax, or e-mail the registration form to Legato Customer Service.

After receiving your completed registration form, Legato will return a unique

authorization code to you.

How to Enter the Authorization Code

You have 45 days from the time you enter your permanent enabler code to enter theauthorization code. After that time, the software is automatically disabled and you canno longer use the NetWorker Module software for backup operations.

To continue using and permanently enable the NetWorker Modulesoftware, enteryour authorization code in the License Registration dialog box, as follows:

1. Click Registration in the Configure tab to open the Registration window.

2. Right-click the product icon.

3. Select Edit from the pop-up menu to open the Edit Registration dialog box.

4. Enter the authorization code for NetWorker Module in the Auth Code text box.Click OK.

After you enter this code, the following message is displayed in the Expiration Datetext box:

Authorized No expiration date

Your NetWorker Module server is then fully enabled and authorized and operates withno further restrictions.

Important: If you move the NetWorker Module software from one computer toanother or change the network address of a computer after the software is installed,you must obtain a new authorization code. If you need to move your software orreconfigure your network, first contact Legato Customer Service to obtain aHostTransfer Affidavitto avoid an interruption in yourscheduled backups.


23/23


Web Registration and Authorization

Legato offers registration and authorization services through the web so you canregister and authorize your Legato products in minutes. These services are available 7days a week, 24 hours a day.

From the Legato home page at www.legato.com, click the eBusiness eNitiative button.When the Legato eBusiness site page appears, follow the step-by-step instructions. Foronline security purposes, be ready to enter your company code and contact code whenrequested.

Important: Legato Web Registration and Authorization is available for all Legatoproducts except Open File Connection, Replica for Windows NT, Replica for NetWare,Legato NetWorker Storage Node for MPE/iX, and Legato NetWorker ClientPakforHP MPE/iX.

Removing the NetWorker Module Software

To remove the NetWorker Module software:

1. Open the folder on the CD-ROM or hard drive from which you installed theNetWorker Module software, and run setup.exeto start the NetWorker Modulesetup program.

2. Click Uninstall, and then click Next.

3. When removing the NetWorker Modulesoftware from a cluster, you must performthe uninstall procedure on each cluster node.

Documents

Exchange Modul Install