Embed Size (px)
Citation preview
VOL. 4601/2021
with Motors and Drivers from Oriental Motor
Exceptional Accuracy
APPLICATION EXAMPLE
2
Positioning Operations are increasingly completed by Conveyor Belts
Conveyor belts are usually driven by three-phase motors paired with frequency inverters, or by BLDC motors with controllers. The belt can be stopped using an external sensor input if required.
Stop Position DeviationDepending on weight of the workpieces and the resulting friction that occurs, the belt can overtravel, causing the stop position to vary.
Application: Transport and positioning of workpieces
Unde�ned Overtravel
Stop SensorMotor
www.orientalmotor.eu | 3
APPLICATION EXAMPLE
Improved Stopping Accuracy with Straightforward Controls
Stepper motors with SC type CVD Series drivers offer an interesting solution for more precise positioning.
When the motor is at a standstill, a holding torque of 50 % of the rated torque of the motor will be applied, maintaining the position of the load.
Unde�ned Overtravel
Stop SensorMotor
Improved Stop Position Repeatability The weight of the workpieces and the resulting friction that occurs will not result in overtravel, so the stop position remains stable.
Application: Transport and positioning of workpieces
4
SOLUTION
Speed 1
Speed 2
FWD Input
RVS Input
M0 Input
Speed 1
Speed 2
FWD Input
RVS Input
M0 Input
Motor Driver
I/O control
24 VDC Power supply
Forward/Reverse Two speed operation
Easy to configure Digital Control Type
Simple Speed Setting
Control
Speed Setting
Setting up two Operating SpeedsForward/Reverse movement is triggered using the FWD/RVS digital inputs.
Speed, acceleration time, and operating current can be set with switches.
Bene�t from the precision and speed stability of an extremely smooth-running stepper motor without the use of an external pulse generator.
Two speeds can be set directly on driver board. These can be selected via the M0 digital input.
When the motor receives a stop signal, the deceleration rate will not be affected by varying friction or inertia loads.
The deceleration time can be set together with the acceleration time in increments of; 0.00s, 0.05s, 0.10s, 0.20s, 0.50s, 1.00s, 2.00s, and 3.00s, for speeds of up to 600 rpm.
When the motor is at a standstill, a holding torque of 50% of the rated torque of the motor will be applied, maintaining the position of the load.
Improved Stopping Accuracy through use of a predefined Deceleration Period
Standstill Torque
Braking Time
PKP Stepper Motors with CVD Series SC Type
Speed
FWD InputUnde�ned Overtravel
Stopping without being affected by a load
Precise braking with a de�ned deceleration rate
5
NEW PRODUCTS
Driver for PKP Stepper Motors CVD Series RS-485 Interface Type
Controlled with Modbus RTU
Connect up to 31 axes
No external pulse generator
necessary
● Setting the operation data and parameters, as well as inputting motion commands, can be done via the RS-485 interface.● The protocol is compatible with Modbus RTU and can be used with a host controller.
● Operation data can be set and controlled for positioning operation (max. number of operation data sets: 256)● Speed, target position and motor current (torque) can be changed immediately via communication while the operation data a motion block is running.
● A maximum of 31 axes can be connected to a host controller. (Total length of all communication cables: up to 10 m)
In addition to controlling the motion profiles, the status (speed, alarm, temperature, etc.) can also be monitored via the RS-485 interface.
Inputs/Outputs
Motor connection
Motor selection switch
Set the terminating resistance of the RS-485 interface
RS-485 interface
USB connection
Modbus RTU
24 VDC power supply
HMI(Touchpanel)
MEXE02Data setting software
(free download)
PC
HMI(Touchpanel)
www.orientalmotor.eu | 6
FEATURED PRODUCTS
The most Compact High Performance Driver in the Industry
Driver for PKP Stepper Motors CVD Series RS-485 Interface Type
Compact, lightweight drivers that are smaller than a business card
The motors are controlled by drivers with an RS-485 interface and a PC with image processing software
Stepper motor driven XYZ system controlled by an HMI
www.orientalmotor.eu | 7
INFO-CENTER
Customer Service Motor Selection
We will be happy to con�gure a motor for you based on the technical information you provide. Your selection of the appropriate drive is completely free of charge and without obligation.
Please visit our website at: https://www.orientalmotor.eu/Info_center/Service/Motor_selection
If you have any questions,please do not hesitateto contact us on00800-22 55 66 22(Free Call Europe).
Example:Belt Drive Application
CHIT
ES
FRDE
UK
www.orientalmotor.eu/Downloads
Do you need information about our products? Our latest �yers, brochures and catalogues can be downloaded from our website:
ADDITIONAL INFORMATION
Please register for our digital technical magazine and get Solution ideas for your application.
YOU CAN REACH USCustomer Service Center
Mon - Thu: 08:00 - 16:30 CETFriday: 08:00 - 15:00 CET
00800 – 22556622
www.orientalmotor.eu
Free Call Europe
Order this brochure free of charge at [email protected]
EDITOR:Oriental Motor (Europa) GmbH Schiessstraße 44, 40549 Düsseldorf Phone: 0211-5206700www.orientalmotor.de Managing Director: Jiro Kuribayashi, Hirokazu Haravda, Eiji KawahitoFrequency of publication: Monthly
The information in this brochure is presented as general information. For accurate technical speci�cations please contact the Oriental Motor (Europa) GmbH of�ce.
This brochure was published in Januar 2021.
EDITORS OFFICE:Paul Jepson, Dominik Ped, Andreas Rey, Franziska Rot, Arne Schipper, Katja Wolf PROOF:ALBERSDRUCK GmbH & Co. KG Leichlinger Straße 11, 40591 Düsseldorf PICTURE PROOF:Adobe Stock, Freepik, The Noun Project
www.orientalmotor.euOnline-Shop
Try it yourself!
You can �nd instructions in the
following video:
© Copyright Oriental Motor (Europa) GmbH 2021
IMPRESSUM
ORIGAMI CAT
