Evolution Fasteners Product Guide 2015 - PRE RELEASE EDITION

PRODUCT GUIDE 2015

2 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

E & O E

TEK 4 - 35

INSULATION 36 - 43

MASONRY SCREWS & ANCHORS 44 - 51

DRYWALL 52 - 75

WOODMASTER RANGE 76 - 81

ACCESSORIES 82 - 89

COATINGS 90 - 91

CE MARKING 92

TERMS & CONDITIONS 95

3

CONTENTSCONTENTS

[email protected] www.evolutionfasteners.co.ukPage 3

4 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSTANDARD TEK - LIGHT SECTION

Standard TekBonded Hex Washer Head Tek 3 For 1.2mm - 3.5mm Steel

TECHNICAL

Designed For: Fixing cladding and roofing applicationsto hot and cold rolled purlins/rails

Head Style: HexagonalDrive: 5/16” hexagonalWasher: 16mm Ø bonded EPDMThread Form: Coarse thread (Tek 3)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®

✓ Evoshield Coating

Designed For: Fastening in aluminium sheeting and panelsHead Style: HexagonalDrive: 5/16” hexagonalWasher: 16mm Ø bonded EPDMThread Form: Coarse thread (Tek 3)Shank Material: Stainless steelMaterial Grade: 304/Euro A2

✓ Stainless Steel

Use with this range:

Magnetic Drive Socket MES5/16

[email protected] www.evolutionfasteners.co.uk

TEK SCREWSSTANDARD TEK - LIG

HT SECTION

Standard TekBonded Hex Washer Head Tek 3 For 1.2mm - 3.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head with bonded washer✓ Precision formed concave fluting gives speedy chip removal✓ Bonded steel washer can act as isolation between substrate and fixture, as an

aid to clamping where fixture clearance hole sizes require, and as a weatherseal

✓ Reduced heat loss when used with external cladding✓ High carbon, high performance drill point ensures

superior drilling characteristics, giving accuratedrilling every time

✓ Bi-metal fasteners have welded, hardened carbonsteel drill point married to a 304/Euro A2 gradestainless steel shank

✓ Ultimate corrosion protection to ensure long-termfastener integrity

✓ Evoshield Coating ✓ Stainless Steel

Code Size Box Carton EvoshieldCoating

StainlessSteel

TSBW5.5-26-3 5.5 x 26mm 250 3,500 ✓

TSBW5.5-32-3 5.5 x 32mm 250 3,500 ✓

TSBW5.5-38-3 5.5 x 38mm 250 3,000 ✓

TSBW5.5-50-3 5.5 x 50mm 100 1,400 ✓

TSBW5.5-60-3 5.5 x 60mm 100 1,400 ✓

TSBW5.5-75-3 5.5 x 75mm 100 1,400 ✓

TSBW5.5-100-3 5.5 x 100mm 100 1,200 ✓

BMBW5.5-25-3 5.5 x 25mm 200 2,000 ✓

BMBW5.5-38-3 5.5 x 38mm 200 2,000 ✓

BMBW5.5-50-3 5.5 x 50mm 100 1,000 ✓

BMBW5.5-135-3 5.5 x 135mm 100 1,000 ✓

6 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

STANDARD TEK - HEAVY SECTION

TEK SCREWS

Standard TekBonded Hex Washer Head Tek 5 For 4mm - 12.5mm Steel

TECHNICAL


Head Style: HexagonalDrive: 5/16” hexagonalWasher: 16mm Ø bonded EPDMThread Form: Fine thread (Tek 5)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Fastening in aluminium sheeting and panelsHead Style: HexagonalDrive: 5/16” hexagonalWasher: 16mm Ø bonded EPDMThread Form: Fine thread (Tek 5)Shank Material: Stainless steelMaterial Grade: 304/Euro A2

✓ Stainless Steel




PRODUCT NAME

TEK SCREWSSTANDARD TEK - H

EAVY SECTION

Standard TekBonded Hex Washer Head Tek 5 For 4mm - 12.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head with bonded washer✓ Precision formed concave fluting gives speedy chip removal✓ Bonded steel washer can act as isolation between substrate and fixture, as an

aid to clamping where fixture clearance hole sizes require, and as a weatherseal







StainlessSteel

TSBW5.5-38-5 5.5 x 38mm 100 2,400 ✓

TSBW5.5-50-5 5.5 x 50mm 100 1,400 ✓

TSBW5.5-60-5 5.5 x 60mm 100 1,400 ✓

TSBW5.5-70-5 5.5 x 70mm 100 1,400 ✓

TSBW5.5-85-5 5.5 x 85mm 100 1,400 ✓

TSBW5.5-100-5 5.5 x 100mm 100 1,200 ✓

BMBW5.5-38-5 5.5 x 38mm 200 2,000 ✓

BMBW5.5-65-5 5.5 x 65mm 100 1,000 ✓

BMBW5.5-100-5 5.5 x 100mm 100 1,000 ✓

8 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSTANDARD TEK - LIGHT SECTION

Standard TekUnwashered Hex Head Tek 3 For 1.2mm - 3.5mm Steel

TECHNICAL


Head Style: HexagonalDrive: 5/16” hexagonalThread Form: Fine thread (Tek 5)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Fastening in aluminium sheeting and panelsHead Style: HexagonalDrive: 5/16” hexagonalThread Form: Fine thread (Tek 5)Shank Material: Stainless steelMaterial Grade: 304/Euro A2

✓ Stainless Steel




PRODUCT NAME

TEK SCREWSPRODUCT NAME

STANDARD TEK - LIG

HT SECTION

Standard TekUnwashered Hex Head Tek 3 For 1.2mm - 3.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design provides sure clamping action✓ Precision formed concave fluting gives speedy chip removal✓ Aggresive thread form design guarantees consistent tapping and superb holding

power







StainlessSteel

TSHW4.8-16-3 4.8 x 16mm 500 10,000 ✓

TSHW5.5-19-3 5.5 x 19mm 250 3,500 ✓

TSHW5.5-25-3 5.5 x 25mm 250 3,500 ✓

TSHW5.5-32-3 5.5 x 32mm 250 3,500 ✓

TSHW5.5-38-3 5.5 x 38mm 250 3,500 ✓

TSHW5.5-50-3 5.5 x 50mm 100 1,400 ✓

TSHW5.5-75-3 5.5 x 75mm 100 1,400 ✓

TSHW5.5-100-3 5.5 x 100mm 100 1,400 ✓

BMHH5.5-25-3 5.5 x 25mm 200 2,000 ✓

BMHH5.5-38-3 5.5 x 38mm 200 2,000 ✓

BMHH5.5-50-3 5.5 x 50mm 100 1,000 ✓

BMHH5.5-65-3 5.5 x 65mm 100 1,000 ✓

BMHH5.5-80-3 5.5 x 80mm 100 1,000 ✓

BMHH5.5-100-3 5.5 x 100mm 100 1,000 ✓

10 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

PRODUCT NAMEPRODUCT NAME

10 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100




TEK SCREWSSTANDARD TEK - HEAVY SECTION

Standard TekUnwashered Hex Head Tek 5 For 4mm - 12.5mm Steel

TECHNICAL


Head Style: HexagonalDrive: 5/16” hexagonalThread Form: Fine thread (Tek 5)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Fastening in aluminium sheeting and panelsHead Style: HexagonalDrive: 5/16” hexagonalThread Form: Fine thread (Tek 5)Shank Material: Stainless steelMaterial Grade: 304/Euro A2

✓ Stainless Steel









TEK SCREWSSTANDARD TEK - H

EAVY SECTION

Standard TekUnwashered Hex Head Tek 5 For 4mm - 12.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design provides sure clamping action✓ Precision formed concave fluting gives speedy chip removal✓ Aggressive thread form design guarantees consistent tapping and superb holding

power

✓ Reduced heat loss when used with external cladding✓ High carbon, high performance drill point ensures superior drilling

characteristics, giving accurate drilling every time✓ Bi-metal fasteners have welded, hardened carbon steel drill point married to a

304/Euro A2 grade stainless steel shank✓ Ultimate corrosion protection to ensure long-term fastener integrity



StainlessSteel

TSHW5.5-32-5 5.5 x 32mm 100 2,400 ✓

TSHW5.5-38-5 5.5 x 38mm 100 2,400 ✓

TSHW5.5-50-5 5.5 x 50mm 100 1,400 ✓

TSHW5.5-75-5 5.5 x 75mm 100 1,400 ✓

TSHW5.5-100-5 5.5 x 100mm 100 1,400 ✓

BMHH5.5-38-5 5.5 x 38mm 100 2,000 ✓

BMHH5.5-50-5 5.5 x 50mm 100 1,000 ✓

12 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSUPER TEK - HEAVY SECTION

Super TekHex Head Tek 7 / Tek 8

TECHNICAL

Unwashered Hex Head Tek 7Designed For: Fixing steel to steelHead Style: HexagonalDrive: 5/16” hexagonalThread Form: 24 threads per inch fine thread, ‘V’ flutedDrill Point: Tek 7 spiral pointShank Material: Carbon steelMaterial Grade: AISI C1022Coating: 1,000hr Evoshield®

Recommended Drill Speed: 1,500 - 2,500 RPMSteel Thickness: 4.0mm - 18.0mm ✓ Evoshield Coating

Unwashered Hex Head Tek 8Designed For: Fixing steel to steelHead Style: HexagonalDrive: 5/16” hexagonalThread Form: 14 threads per inch intermediate thread, ‘V’ flutedDrill Point: Tek 8 spiral pointShank Material: Carbon steelMaterial Grade: AISI C1022Coating: 1,000hr Evoshield®

Recommended Drill Speed: 1,500 - 2,500 RPMSteel Thickness: 4.0mm - 22.0mmEffective Thread Length: 32mm

Washered Hex Head Tek 7All of the above PLUS:Washer: 16mm Ø bonded EPDM


TEK SCREWSSUPER TEK - H

EAVY SECTION

Super TekHex Head Tek 7 / Tek 8

Unwashered Hex Head Tek 7✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design provides sure clamping action✓ Precision formed concave fluting ensures speedy chip removal✓ Aggressive thread form design ensures consistent tapping and superb holding power

Washered Hex Head Tek 7✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head with bonded washer✓ Precision formed concave fluting ensures speedy chip removal✓ Bonded steel washer can act as isolation between substrate and fixture, and as a

weatherseal

Unwashered Hex Head Tek 8✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design provides sure clamping action✓ Precision formed concave fluting gives speedy chip removal✓ Aggresive thread form design guarantees consistent

tapping and superb holding power


Code Size Box Carton UnwasheredHead

WasheredHead

TSHW5.5-50-7 5.5 x 50mm 100 1,400 ✓

TSBW5.5-50-7 5.5 x 50mm 100 1,400 ✓

TSHW6.3-60-8 6.3 x 60mm 100 1,000 ✓



14 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSUPER WING DRILL - HEAVY SECTION

Super Wing DrillCountersunk Tek 7For 4mm - 18mm Steel

TECHNICAL

EUROPA

EN 14592

2008 = 01DW-01/14

Countersunk Head Tek 7Designed For: When timber is being fastened to thicker steel

section or where extremely hard steels defeatnormal tek screws

Head Style: Double CountersunkDrive: Torx 30Thread Form: 24 threads per inch fine thread, ‘V’ flutedDrill Point: Tek 7 spiral pointShank Material: Carbon steelMaterial Grade: AISI C1022Coating: 1,000hr Evoshield®

Recommended Drill Speed: 1,500 - 2,500 RPMSteel Thickness: 4.0mm - 18mm


TEK SCREWSSUPER WING DRILL - H

EAVY SECTION


TSTF5.5-73-7 5.5 x 73mm 100 1,400 ✓

TSTF5.5-80-3 5.5 x 80mm 100 1,400 ✓

TSTF5.5-93-7 5.5 x 93mm 100 1,400 ✓

Super Wing DrillCountersunk Tek 7For 4mm - 18mm Steel

EUROPA

EN 14592

2008 = 01DW-01/14


16 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSTITCHING & METAL FRAMING

Stitching Screws

TECHNICAL

Designed For: Stitching cladding panelsShank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®

Recommended Drill Speed 1,500 - 2,500 RPM


Designed For: Fixing steel to steelShank Material: Carbon steelMaterial Grade: AISI C1022Recommended Drill Speed: 1,500 - 2,500 RPM

✓ Zinc Coating


TEK SCREWSSTITC

HING & METAL FR

AMING

Stitching Screws

✓ Evoshield Coating✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design gives a sure clamping action ✓ Precision formed concave fluting ensures speedy chip removal ✓ High grade carbon steel (C1022) helps prevent head snap ✓ Silver Evoshield® coating with 500hr salt spray rating

✓ Zinc Coating✓ Fastening where a high end corrosion resistant coating is not required


Zinc Coating Bi-metal

TSFHR6.3-22-2 6.3 x 22mm 200 4,800 ✓

TSFHR8.0-25-1 8.0 x 25mm 100 2,400 ✓

ZS22-2 6.3 x 22mm 200 2,800 ✓

BMTSFHR6.3-22-2 6.3 x 22mm ✓

✓ Evoshield Coating ✓ Zinc Coating ✓ Bi-metal

18 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSSTITCHING & METAL FRAMING

Metal Framing

TECHNICAL

Designed For: Fixing steel to steelHead Style: Low ProfileDrive: Phillips 3Thread Form: Coarse thread (Tek 3) / fine thread (Tek 5)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Stitching cladding railsHead Style: PancakeDrive: Phillips 3Thread Form: CoarseShank Material: Stainless SteelMaterial Grade: 304/Euro A2 OR 410Recommended Drill Speed: 1,500 - 2,500 RPM

✓ Stainless Steel

EUROPA

EN 14566 2002/95/EC


TEK SCREWSSTITC

HING & METAL FR

AMING

Metal Framing1.2mm - 3.5mm SteelThickness

✓ High grade carbon steel✓ Super hard and sharp drill tips ensure fast drill times✓ Superior corrosion protection to guarantee long-term fastener integrity ✓ Fully threaded for application versatility

✓ Super hard, super sharp drill tip✓ The bright silver surface of stainless steel fasteners provides a contemporary

and attractive appearance which is easily maintained✓ Often the best value option over the total life of the project, despite higher initial

costs



StainlessSteel

TSLP4.8-22-2 4.8 x 22mm 500 6,000 ✓

TSLP5.5-38-5 5.5 x 38mm 200 4,800 ✓

TSPH4.8-16-3 4.8 x 16mm 500 12,000 ✓

TSPH5.5-19-3 5.5 x 19mm 500 7,000 ✓

TSPH5.5-25-3 5.5 x 25mm 200 4,800 ✓

SSPH5.5-19-3 5.5 x 19mm 500 5,000 ✓

EUROPA

EN 14566 2002/95/EC

20 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSCOMPOSITE PANEL - LIGHT SECTION

Composite Panel

TECHNICAL

Designed For: Fixing cladding and roofing applications to hot and cold rolledpurlins/rails Fastening liner panels and general components to steel



Designed For: Fastening in aluminium sheeting and panelsHead Style: HexagonalDrive: 5/16” hexagonalWasher: 16mm Ø bonded EPDMThread Form: High thread Dril Point: Tek 3Shank Material: Stainless steelMaterial Grade: 304/Euro A2Coating: Electroplated zinc

✓ Stainless Steel




TEK SCREWSCOMPOSITE PA

NEL - LIG

HT SECTION

Composite Panel1.2mm - 3.5mm Steel Thickness

✓ Super hard, super sharp drill tips ensure fast drill times and eliminates ‘walking’

✓ Unthreaded piece ensures panel surfaces are not deformed✓ Precision formed concave fluting gives speedy chip removal✓ Sharp tapping threads ensure a low torque fixing every time

✓ Reduced heat loss when used with external cladding✓ High carbon, high performance drill point ensures superior drilling

characteristics, giving accurate drilling every time✓ Bi-metal fasteners have welded, hardened carbon steel drill point married to a

304/Euro A2 grade stainless steel shank✓ Ultimate corrosion protection to ensure long-term fastener integrity



StainlessSteel

TSBWHT5.5-80-3 5.5 x 80mm 100 1,400 ✓

TSBWHT5.5-105-3 5.5 x 105mm 100 1,200 ✓

TSBWHT5.5-135-3 5.5 x 135mm 100 1,200 ✓

TSBWHT5.5-150-3 5.5 x 150mm 100 900 ✓

TSBWHT19-5.5-185-3 5.5 x 185mm 50 300 ✓

TSBWHT19-5.5-225-3 5.5 x 225mm 50 300 ✓

BMTSBWHT5.5-60-3 5.5 x 60mm 100 1,000 ✓

BMTSBWHT5.5-80-3 5.5 x 80mm 100 1,000 ✓

BMTSBWHT5.5-105-3 5.5 x 105mm 100 1,000 ✓

BMTSBWHT5.5-135-3 5.5 x 135mm 100 1,000 ✓

BMTSBWHT5.5-150-3 5.5 x 150mm 100 1,000 ✓

22 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSHEAVY SECTION COMPOSITE PANEL

Heavy SectionComposite Panel

TECHNICAL

Designed For: Fixing cladding and roofing applications to hot and cold rolledpurlins/rails Fastening liner panels and general components toheavy steel






TEK SCREWSHEAVY SECTION COMPOSITE PA

NEL

Heavy SectionComposite Panel4 - 12.5mm Steel Thickness✓ Super hard, super sharp drill tips ensure fast drill

times and eliminates ‘walking’ ✓ Unthreaded piece ensures panel surfaces are not deformed✓ Precision formed concave fluting gives speedy chip removal✓ Sharp tapping threads ensure a low torque fixing every time



TSBWHT5.5-85-5 5.5 x 85mm 100 1,400 ✓

TSBWHT5.5-105-5 5.5 x 105mm 100 1,200 ✓

TSBWHT5.5-135-5 5.5 x 135mm 100 1,200 ✓

TSBWHT5.5-150-5 5.5 x 150mm 100 1,000 ✓

24 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSTIMBER TEK - LIGHT SECTION

Timber TekFor 1.2mm - 3.5mm Steel

TECHNICAL

Designed For: Fixing timber or composites to steelHead Style: Countersunk or countersunk with nibsDrive: Phillips 3Thread Form: Coarse thread (Tek 3)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Fastening when stainless steelproduct is required, e.g. inaluminium sheeting and panels

Head Style: CountersunkDrive: Phillips 3Thread Form: Coarse thread (Tek 3)Shank Material: Stainless steelMaterial Grade: AISI A304Recommended Drill speed: 1,500 - 2,500 RPM

✓ Stainless Steel

EUROPA

EN 14566


Magnetic Bit HolderMB1060


TEK SCREWSTIMBER TEK - LIG

HT SECTION

Timber TekFor 1.2mm - 3.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Countersinking nibs under head provide flush finish✓ Precision formed concave fluting gives speedy chip removal✓ Aggressive thread form design guarantees consistent tapping and superb holding

power

✓ High carbon, high performance drill point ensures superior drilling characteristics,giving accurate drilling every time

✓ Bi-metal fasteners have welded, hardened carbon steel drill point married to a304/Euro A2 grade stainless steel shank

✓ Ultimate corrosion protection to ensure long-term fastener integrity



StainlessSteel

TSTF4.2-38-3 4.2 x 38mm 200 4,800 ✓

TSTF4.8-45-3 4.8 x 45mm 100 2,400 ✓

TSTF5.5-50-3 5.5 x 50mm 200 2,800 ✓

TSTF5.5-62-3 5.5 x 62mm 200 2,800 ✓

TSTF5.5-80-3 5.5 x 80mm 100 1,400 ✓

TSTF5.5-100-3 5.5 x 100mm 100 1,400 ✓

TSTF5.5-120-3 5.5 x 120mm 100 1,400 ✓

TSTF5.5-150-3 5.5 x 150mm 100 1,200 ✓

TSTF5.5-180-3 5.5 x 180mm 100 1,200 ✓

BMWD4.8-38-3 4.8 x 38mm 200 4,800 ✓

BMWD5.5-62-3 5.5 x 62mm 100 1,000 ✓

BMWD5.5-80-3 5.5 x 80mm 100 1,000 ✓

EUROPA

EN 14566

26 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSTIMBER TEK - HEAVY SECTION

Timber TekFor 4mm - 12.5mm Steel

TECHNICAL

Designed For: Fixing timber or composites to steelHead Style: Countersunk Drive: Phillips 3Thread Form: Fine thread (Tek 5)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®


Designed For: Fastening when stainless steelproduct is required, e.g. inaluminium sheeting and panels

Head Style: CountersunkDrive: Phillips 3Thread Form: Fine thread (Tek 5)Shank Material: Stainless steelMaterial Grade: AISI A304Recommended Drill speed: 1,500 - 2,500 RPM

✓ Stainless Steel




TEK SCREWSTIMBER TEK - H

EAVY SECTION

Timber TekFor 4mm - 12.5mm Steel

✓ Super hard, super sharp drill tips ensure fast drill times✓ Countersinking nibs under head provide flush finish✓ Precision formed concave fluting gives speedy chip removal✓ Aggressive thread form design guarantees consistent tapping and superb holding

power

✓ High carbon, high performance drill point ensures superior drilling characteristics,giving accurate drilling every time

✓ Bi-metal fasteners have welded, hardened carbon steel drill point married to a304/Euro A2 grade stainless steel shank

✓ Ultimate corrosion protection to ensure long-term fastener integrity



StainlessSteel

TSTF5.5-42-5 5.5 x 42mm 100 2,400 ✓

TSTF5.5-65-5 5.5 x 65mm 200 2,800 ✓

TSTF5.5-85-5 5.5 x 85mm 100 1,400 ✓

TSTF5.5-100-5 5.5 x 100mm 100 1,400 ✓

TSTF5.5-110-5 5.5 x 110mm 100 1,400 ✓

TSTF5.5-135-5 5.5 x 135mm 100 1,200 ✓

TSTF5.5-150- 5.5 x 150 mm 100 1,200 ✓

TSTF5.5-180-5 5.5 x 180 mm 100 1,200 ✓

TSTF6.3-60-4 6.3 x 60mm 100 1,200 ✓

TSTF6.3-85-4 6.3 x 85mm 100 1,200 ✓

BMWD5.5-65-5 5.5 x 65mm 100 1,000 ✓

BMWD5.5-85-5 5.5 x 85mm 100 1,000 ✓

BMWD5.5-135-5 5.5 x 135mm 100 1,000 ✓

Also see Super Tek Wing Drill on p 14 - 15

28 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSCOMPOSITE PANEL FOR TIMBER

Composite Panel for TimberTECHNICAL



Designed For: Fixing cladding and profiled sheeting totimber purlins and studs

Head Style: Hexagonal Drive: 5/16” Hex HeadWasher: 16mm Bonder EPDMThread Form: Coarse (Type 17 cutter tip)Shank Material: Carbon steelMaterial Grade: AISI C1022Coating: 500hr Evoshield®

✓ Type 17 Cutter Point ensures fast advancement in timber and ply✓ Aggresive Threadform: Improves penetration and reduces required drive torque✓ Unthreaded piece ensure panels are not deformed.


TEK SCREWSCOMPOSITE PA

NEL FO

R TIMBER

Composite Panel for Timber



TSBWHT6.3-80-GP 6.3 x 80mm 100 1,400 ✓

TSBWHT6.3-100-GP 6.3 x 100mm 100 1,200 ✓

TSBWHT6.3-125-GP 6.3 x 125mm 100 1,200 ✓

TSBWHT6.3-150-GP 6.3 x 150mm 100 900 ✓

30 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

TEK SCREWSCLADDING & SIDING

Miscellaneous Hex HeadTECHNICAL

Designed For: Fixing fibrous cement sheets to timberHead Style: HexagonalDrive: 5/16” hexagonalWasher: BAZ typeThread Form: SingleMaterial Grade: AISI C1022Drill Point: Gash pointEffective Thread Length: Fully threadedCoating: 500hr Silver Evoshield®


Designed For: Fixing timber batons, trunking, track and generalcomponents into concrete and masonry substrates.Also for fixing metal sheets to timber purlins

Head Style: Slotted hexagonalDrive: 5/16” hexagonal with slotThread Form: Hi-LoDrill Point: Type 17Material Grade: SAE 410 stainless steel

✓ Stainless Steel

Designed For: Fixing timber batons, trunking, track and generalcomponents into concrete and masonry substrates.Also for fixing metal sheets to timber purlins

Head Style: Slotted hexagonalDrive: 5/16” hexagonal with slotThread Form: SingleDrill Point: Type 17Material Grade: Zinc

✓ Zinc Coating

2002/95/EC


TEK SCREWSCLADDING & SIDING

Miscellaneous Hex Head✓ Replaces hook bolts and drive screws✓ Wings on shank will ream a clearance hole in the sheets✓ Precision formed concave fluting ensures speedy chip removal✓ Sharp tapping threads ensure a low torque fixing every time

✓ Fully threaded for application versatility✓ 16mm bonded EPDM washer✓ The gash point makes the initial penetration of the metal sheet easier✓ Sharp tapping threads ensure a low torque, sure fixing every time

✓ Evoshield Coating ✓ Zinc Coated ✓ Stainless Steel


ZincCoating

StainlessSteel

SSDH6.3-110-GP 6.3 x 110mm 100 600 ✓

SSDH6.3-130-GP 6.3 x 130mm 100 600 ✓

TSBW6.3-25-GP 6.3 x 25mm 200 2,800 ✓

TSBW6.3-32-GP 6.3 x 32mm 200 2,800 ✓

TSBW6.3-45-GP 6.3 x 45mm 200 2,400 ✓

TSBW6.3-60-GP 6.3 x 60mm 100 1,400 ✓

TSBW6.3-80-GP 6.3 x 80mm 100 1,400 ✓

TSBW6.3-100-GP 6.3 x 100mm 100 1,200 ✓

SSMSHH6.3-32-GP 6.3 x 32mm 200 2,800 ✓

SSMSHH6.3-45-GP 6.3 x 45mm 200 2,400 ✓

✓ Type 17 cutter point for fast advancement through timber and penetration of thinsteel sections

✓ Cutter point reduces torque to stop timber splitting✓ Hi-Lo thread form for superior pull-out resistance in timber, steel, masonry and

concrete substrates✓ Slotted hexagonal head for positive, stable driving characteristics

32 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

ECONOMY TEK SCREWSECONOMY RANGE

Standard Tek ZincBonded Hex Washer Head Tek 3 / Tek 5

Designed For: Fastening where a high end corrosion resistant coating is not requiredHead Style: HexagonalDrive: 5/16” hexagonalThread Form: Coarse thread (Tek 3) / fine thread (Tek 5)Material Grade: AISI C1022

✓ Zinc Coating



✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head with bonded washer✓ Precision formed concave fluting ensures speedy chip removal✓ Bonded steel washer can act as isolation between substrate and fixture, as an aid to

clamping where fixture clearance holes require, and as a weatherseal

Code Size Steel Thickness Box Carton Zinc Coating

BWZ25-3 5.5 x 25mm 1.2 - 3.5 mm 200 2,800 ✓

BWZ32-3 5.5 x 32mm 1.2 - 3.5 mm 200 2,800 ✓

BWZ38-3 5.5 x 38mm 1.2 - 3.5 mm 200 2,800 ✓

BWZ50-3 5.5 x 50mm 1.2 - 3.5 mm 100 1,400 ✓

BWZ75-3 5.5 x 75mm 1.2 - 3.5 mm 100 1,400 ✓

BWZ38-5 5.5 x 38mm 4 - 12.5 mm 200 2,400 ✓

BWZ50-5 5.5 x 50mm 4 - 12.5 mm 100 1,400 ✓






Standard Tek ZincUnwashered Hex Head Tek 3 / Tek 5

Designed For: Fastening where a high end corrosion resistant coating is not requiredHead Style: HexagonalDrive: 5/16” hexagonalThread Form: Coarse thread (Tek 3) / fine thread (Tek 5)Material Grade: AISI C1022

✓ Zinc Coating

✓ Super hard, super sharp drill tips ensure fast drill times✓ Hex flange head design provides sure clamping action✓ Precision formed concave fluting gives speedy chip removal✓ Aggressive thread form design guarantees consistent tapping and superb holding

power

Code Size Steel Thickness Box Carton ZincCoating

HWZ25-3 5.5 x 25mm 1.2 - 3.5 mm 200 2,800 ✓

HWZ32-3 5.5 x 32mm 1.2 - 3.5 mm 200 2,800 ✓

HWZ38-3 5.5 x 38mm 1.2 - 3.5 mm 200 2,800 ✓

HWZ50-3 5.5 x 50mm 1.2 - 3.5 mm 100 1,400 ✓

HWZ75-3 5.5 x 75mm 1.2 - 3.5 mm 100 1,400 ✓

HWZ38-5 5.5 x 38mm 4 - 12.5 mm 200 2,400 ✓

HWZ50-5 5.5 x 50mm 4 - 12.5 mm 100 1,400 ✓

34 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100




Timber Tek Zinc

Designed For: Fixing timber or composites to steel where a high endcorrosion resistant coating is not required

Head Style: Countersunk or countersunk with nibs*Drive: Phillips 3Thread Form: Twin, coarse thread (Tek 3) / fine thread (Tek 5)Material Grade: AISI C1022Shank Material: Carbon steelDrilling Capacity: 1.2mm - 3.5mm (Tek 3) / 3.5mm - 12.00mm (Tek 5)Recommended Drill Speed: 1,500 - 2,500 RPM

✓ Zinc Coating

✓ Super hard, super sharp drill tips ensure fast drill times✓ Countersinking nibs under head provide flush finish in fixture✓ Precision formed concave fluting ensures speedy chip removal✓ Aggressive thread form design ensures consistent tapping and superb holding

Code Size Steel Thickness Box Carton ZincCoating

ZWD38-3 4.2 x 38mm 1.2 - 3.5 mm 200 4,800 ✓

ZWD4.8-38-3 4.8 x 38mm 1.2 - 3.5 mm 200 2,800 ✓

ZWD50-3 4.8 x 50mm 1.2 - 3.5 mm 200 2,800 ✓

ZWD62-3 5.5 x 62mm 1.2 - 3.5 mm 200 2,800 ✓

ZWD80-3 5.5 x 80mm 1.2 - 3.5 mm 100 1,400 ✓

ZWD65-5 5.5 x 65mm 4 - 12.5 mm 200 2,800 ✓

ZWD85-5 5.5 x 85mm 4 - 12.5 mm 100 1,400 ✓

EUROPA

EN 14566


TEK SCREWSMISCELLA

NEOUS

MiscellaneousTECHNICAL

Designed For: BMDW Fixing plasterboard to drywall track/timber in humid atmospheres

SSCSK Fixing plasterboard/timber to aluminiumTSHV Assembly/fabrication of ducting/air con systems

Head Style: BMDW CountersunkSSCSK CountersunkTSHV Hexagonal head 5/16”




✓ Reduced heat loss compared to carbon steel/coated fixings✓ 410 grade parts have superior performance characteristics when subjected to heat✓ Stainless steel grades ideal for use in aluminium to mitigate electro-galvanic

corrosion✓ BMDW perfect multi-purpose screw with ‘universal drywall thread’ ensures best

fixing combined with ultimate corrosion resistance

BMDW SSCSK

2002/95/EC

Code Size Box Carton Stainless Steel /Coating

SSCSK4.8-38-3 4.8 x 38mm 500 7,000 410

BMDW4.8-42 4.8 x 42mm 200 4,800 304/A2

TSHV4.2-12-1 4.2 x 12mm 1,000 10,000 Zinc

TSHV4.8-15-1 4.8 x 15mm 1,000 10,000 Zinc

36 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

INSULATION FIXINGSSELF DRILLING INSULATION SCREWS

Self Drilling Insulation

Designed For: Fixing insulation to steel and timber purlinsHead Style: BugleDrive: Phillips 2Thread Form: TwinMaterial Grade: AISI C1022Coating: 500hr Evoshield®

Recommended Drill Speed: 1,500 - 2,500 RPM


✓ Self drilling point and coarse thread allows optimum performance in steel and timbersubstrates

✓ Bugle head allows use with various washer designs✓ Heat treated carbon steel construction yields material strength of 1,100N/mm2 for

superior physical performance✓ Evoshield® coating provides greater corrosion resistance over the industry standard

of 320 hours

37

INSULATION FIXINGSSELF D

RILLIN

G INSULATION SCREWS



ETKR60 4.8 x 60mm 100 1,000 ✓

ETKR80 4.8 x 80mm 100 1,000 ✓

ETKR100 4.8 x 100mm 100 1,000 ✓

ETKR120 4.8 x 120mm 200 2,400 ✓

ETKR140 4.8 x 140mm 200 2,400 ✓

ETKR160 4.8 x 160mm 200 1,600 ✓

ETKR180 4.8 x 180mm 200 1,600 ✓

ETKR200 4.8 x 200mm 100 800 ✓

ETKR220 4.8 x 220mm 100 900 ✓

ETKR240 4.8 x 240mm 100 900 ✓

ETKR260 4.8 x 260mm 100 900 ✓

ETKR280 4.8 x 280mm 100 900 ✓

ETKR300 4.8 x 300mm 100 900 ✓

Self Drilling Insulation

EUROPA

EN 14566

38 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

INSULATION FIXINGSHEAVY DUTY ROOFING SCREW

Heavy DutyRoofing Screw

Designed For: Fixing Insulation, membrane systemsand ply to various base materials

Head Style: Button Head ( Pan )Drive: PH3Thread Form: Coarse single threadMaterial Grade: AISI C1022Coating: 500hr Evoshield®


✓ Fixing Insulation and membrane systems to Steel and concrete**✓ For fixing ply and other roofing layers to timber✓ Low profile pan head for application versatility✓ Washers also available

** a 5mm pilot hole allows fixing to steel from 1.2 to 2mm, fastener is self piercing in 0.7mm track.** a 5.15mm Pilot hole is required for concrete. Hole must be 15mm deeper than screw embedment.




39

INSULATION FIXINGSHEAVY DUTY ROOFIN

G SCREW



ERGS76 76 mm 100 1,600 ✓

ERGS100 100 mm 100 1,400 ✓

ERGS127 127 mm 100 1,000 ✓

ERGS152 152 mm 100 1,000 ✓

ERGS176 176 mm 50 1,000 ✓

ERGS200 200 mm 50 1,000 ✓

Heavy Duty Roofing Screw

Washer 1 - RW5 and RW18The washers are 46mmdiameter, manufactured fromhigh strength Nylon, Twoversions are available, shortstem with 5mm recess and long stem with 12mm recess.

Washer 2 - RW35 and RW65This products longer lengthrecess allows the fixing to retain the thicker insulationtypes being used in todaysconstruction industry

Washer 3 - ECW60The washer head is 60mm in diameter and with itsadditional sealing capprovides additional coldbridging protection.

For customer convenience we offer three differing types ofretention washer, some with more than one length.

40 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

INSULATION FIXINGSINSULATION RETAINING WASHER

Insulation Retaining WasherDesigned For: For securing insulation to

timber and sheet steel whenused with Evolution drywallscrews.

Colour: White

✓ Evolution Insulation retaining washers are used in conjunction with different screwtypes to secure PIR insulation to timber,steel and masonry.

✓ All of the washers have a recessedmounting point for the screw head, thisensures that the screw head is well belowthe surface, reducing cold bridging.

41

INSULATION FIXINGSINSULATION RETAINING WASHER


Code Size Diameter Box

RW5 5 mm Recess 46 mm 500




ECW60 12 mm Recess 60 mm 500

Insulation Retaining Washer

Evolution Insulation retaining washers can beused in conjunction with:Evolution WoodscrewsDrywall ScrewsMasonry screwsLong length Insulation Screws

42 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

INSULATION FIXINGSPANEL-FIX

Panel-FixInsulation Fixing

Designed For: Quick through-fix for insulationboards into masonry/ aeratedconcrete/ brick/ concrete/ stone

Material Grade: GRP Polyamide 6Shank Material: PolypropyleneColour: WhiteHead Style: Flat

Insulation Support Washer

Designed For: For use with insulation fixing for fixing soft insulation(e.g. Rockwool®)

Colour: White

43

INSULATION FIXINGSPANEL-FIX


Code Size Min drilldepth

Pilot hole

Fixture thickness Box Carton

EVPF50 8.0 x 50 mm 35 mm 8.0 mm 10.0 - 20.0 mm 500 500

EVPF70 8.0 x 70 mm 35 mm 8.0 mm 10.0 - 40.0 mm 500 500

EVPF90 8.0 x 90 mm 35 mm 8.0 mm 10.0 - 60.0 mm 500 500

EVPF110 8.0 x 110 mm 35 mm 8.0 mm 10.0 - 80.0 mm 500 500

EVPF130 8.0 x 130 mm 35 mm 8.0 mm 10.0 - 100.0 mm 500 500

SW90 90 mm 90 mm Ø - - 500 -

Panel Fix

44 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

MASONRY SCREWS & ANCHORSSELF-TAPPING MASONRY SCREW

Self Tapping Masonry Screw

Designed for: Fixing timber battens, trunking, track and generalcomponents into concrete and masonry

Head style: Countersunk or slotted hex headDrive bit: Phillips 2 / Phillips 3 and 5/16 hex for slotted hex headDrill point: Nail pointCoating: 500hr Evoshield®Shank material: Carbon steelMaterial grade: AISI C1022

✓ Countersunk Head

✓ Slotted Head

✓ Head styles - both hex and Csk types available for application versatility. Precision manufacture ensures stick-fit with Csk types.

✓ Aggressive threadform design ensures consistent tapping and superb holding power.

✓ Fast and simple installation, re-usable, no plugs required.

✓ Nail point tip.

✓ 500Hr rated Evoshield TM coating gives high performing corrosion protection, setting standards for surface hardness and integrity.

✓ Non-expansion fixing allows fixing closer to edge of substrate.

45

MASONRY SCREWS & ANCHORSSELF-TA

PPING MASONRY SCREW


Code Size Drive Fixture Build-Up

CountersunkHead

Slotted Hex

HeadBox Carton

MSCSK4.8-32-2 4.8 x 32.0 mm Phillips No 2 0.0 – 7.0mm ✓ 100 3,200












MSCSK6.3-125-3 6.3 x 125.0 mm Phillips No 3 85.0 – 100.0mm ✓ 100 800

MSHH6.3-32-516 6.3 x 32.0 mm 5/16” AF Hex 0.0 – 7.0mm ✓ 100 3,200

MSHH6.3-45-516 6.3 x 45.0 mm 5/16” AF Hex 5.0 – 20.0mm ✓ 100 1,600

MSHH6.3-57-516 6.3 x 57.0 mm 5/16” AF Hex 17.0 – 32.0mm ✓ 100 2,400

MSHH6.3-70-516 6.3 x 70.0 mm 5/16” AF Hex 30.0 – 45.0mm ✓ 100 1,400

MSHH6.3-82-516 6.3 x 82.0 mm 5/16” AF Hex 42.0 – 57.0mm ✓ 100 1,400

MSHH6.3-100-516 6.3 x 100.0 mm 5/16” AF Hex 55.0 – 75.0mm ✓ 100 1,200

Self Tapping Masonry Screw

See also stainless steel masonry screw - p.29

46 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

MASONRY SCREWS & ANCHORSHAMMERFIX

Hammerfix

Designed for Purpose: Through fixing for use in masonryHead Style: Countersunk/ FlatCoating: Zinc with dichromate passivationMaterial Grade: C1022

Designed for Purpose: Quick through-fix installation into solid masonrywhere superior corrosion resistance is required

Head Style: Countersunk/ FlatCoating: Stainless SteelMaterial Grade: AISI 304 (Euro A2)

✓ For quick and easy fixing into solid brick or masonry.

✓ Extensive range to suit most requirements.

✓ High density, fully removable nylon sleeve.

✓ Manufactured from steel and zinc coated.

✓ Time saving application due to pre-assembled screw and plug.

✓ Countersunk head design protects the item being fixed.

CE marked in compliance with the ConstructionProducts Regulations (European Regulation No.305/2011 and with full European Technical Approvals.

✓ Stainless Steel

✓ Carbon Steel

47

MASONRY SCREWS & ANCHORSHAMMERFIX


Hammerfix

Code Size Drill ø

MaxFixture

Thickness

Min Drill

Depth

CarbonSteel

StainlessSteel Box Carton

EHIA640 6.0 x 40.0 mm 6 mm 10 mm 40 mm ✓ 200 2,400

EHIA650 6.0 x 50.0 mm 6 mm 25 mm 40 mm ✓ 200 2,400

EHIA660 6.0 x 60.0 mm 6 mm 35 mm 40 mm ✓ 100 1,200

EHIA680 6.0 x 80.0 mm 6 mm 55 mm 40 mm ✓ 100 1,200

EHIA860 8.0 x 60.0 mm 8 mm 25 mm 50 mm ✓ 100 1,200

EHIA880 8.0 x 80.0 mm 8 mm 40 mm 50 mm ✓ 50 600

EHIA8100 8.0 x 100.0 mm 8 mm 60 mm 50 mm ✓ 50 600

EHIA8120 8.0 x 120.0 mm 8 mm 80 mm 50 mm ✓ 50 600

EHIA8140 8.0 x 140.0 mm 8 mm 95 mm 50 mm ✓ 50 600

EHIA640C 6.0 x 40.0 mm 6 mm 10 mm 40 mm ✓ 200 2,400

SSHS860 8.0 x 60.0 mm 8 mm 20 mm 40 mm ✓ 100 2,000

SSHS8100 8.0 x 100.0 mm 8 mm 60 mm 40 mm ✓ 100 2,000

CE marked in compliance with the Construction ProductsRegulations (European Regulation No. 305/2011 and withfull European Technical Approvals.

48 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

MASONRY SCREWS & ANCHORSCEILING ANCHORS

Steel Ceiling Anchors

Designed for: Use with angle brackets in concrete ceilings whereregulations dictate all steel anchors should be used foroverhead fixings.

Head style: FlatCoating: Passivated zincShank material: Carbon steelMaterial grade: AISI C1022Drill diameter: 6.0mmPilot hole: 6.0mmMin. drill depth: 30.0mmFixture thickness 5.0mmFire tested: Yes, to EN1364-1

THESE PRODUCTSARE FIRETESTED TOEN-1364-1

✓ Manufactured from steel and zinc with a clear passivated coating.

✓ Time saving application due to pre-assembled nature of anchor.

✓ Quick and easy through fix item.

✓ Extensive range to suit most requirements.

✓ High retaining power.

✓ Automatic expansion.

✓ Non-removable.

EUROPA

ETAG001

ETA-13/0063

Code Size Box Carton

EVDBZ640 M6 x 40.0mm 100 2,000

EVDBZ665 M6 x 65.0mm 100 1,000

49

MASONRY SCREWS & ANCHORSWIREHANGERS


Wirehangers

Designed for: Fixing cables/wires in suspended ceiling applications.Head style: FlatSize: M6 x 60.0mmEye diameter: 6.5mmCoating: Clear zinc passivatedShank material: Carbon steelMaterial grade: AISI C1022Drill diameter: 6.0mmPilot hole: 6.0mmMin. drill depth: 35.0mmFire tested: Yes, to EN1364-1

✓ 6.5mm eye to ensure speed of application when attaching wire.

✓ Zinc and clear passivated coating.

✓ Quick and easy installation.

Code Size Eye Diameter

DrillDiameter

Min DrillDepth Box Carton

WH6 M6 x 60.0 mm 6.5 mm 6.0 mm 35.0 mm 100 2,000

50 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

MASONRY SCREWS & ANCHORSANCHORBOLTS

Anchorbolts

Designed for: Fixing to concrete in medium/heavy dutyapplications

Hi-Lo Thread: YesHead Style: Hexagonal boltMaterial Grade: AISI 10B21Drive Bit: Hex socketFixes To: ConcreteCoating: Electroplated zincColour: SilverFixes From: Timber/MetalEffective Thread length: Fully threaded

✓ Manufactured from AISI 10B21 carbon steel with an electroplated zinc coating.

✓ Can be screwed directly into a hole drilled in the substrate without needingadditional fixings or special tools.

✓ Fully threaded.

51

MASONRY SCREWS & ANCHORSANCHORBOLTS


Anchorbolts

Code Size Min Drill Depth Pilot Hole Box Carton

EAB840 8.0 x 40 mm 30 mm 8.0 mm 100 1,200

EAB875 8.0 x 75 mm 60 mm 8.0 mm 100 800

EAB8100 8.0 x 100 mm 60 mm 8.0 mm 50 600

EAB8130 8.0 x 130 mm 60 mm 8.0 mm 50 600

EAB8150 8.0 x 150 mm 60 mm 8.0 mm 25 400

EAB10575 10.5 x 75 mm 60 mm 10.0 mm 50 600

EAB105100 10.5 x 100 mm 60 mm 10.0 mm 50 400

EAB105130 10.5 x 130 mm 60 mm 10.0 mm 25 300

EAB105150 10.5 x 150 mm 60 mm 10.0 mm 25 300

EAB12575 12.5 x 75 mm 70.0 mm 12.0 mm 50 400

EAB125100 12.5 x 100 mm 70.0 mm 12.0 mm 25 300

EAB125130 12.5 x 130 mm 70.0 mm 12.0 mm 25 200

EAB125150 12.5 x 150 mm 70.0 mm 12.0 mm 20 240

EAB1675 16.0 x 75 mm 60.0 mm 16.0mm 25 300

EAB16100 16.0 x 100 mm 70.0 mm 16.0mm 10 160

EAB16150 16.0 x 150 mm 70.0 mm 16.0mm 15 120

52 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLFINE THREAD DRYWALL

EUROPA

EN 14566

2008 = 01DW-01/14

Fine Thread Drywall Screws (Zinc)

Designed For: Fixing plasterboard to metal stud up to 1.2mmHead style: BugleDrive bit: Phillips 2Drill point: Super sharp pointThread form: Twin thread, fineCoating: Electro plated zincShank material: Carbon steelMaterial grade: AISI C1022

✓ Designed to drill through 1mm of steel in 0.5 seconds

✓ Bugle head design for application versatility gives a flush countersink with no papertearing.

✓ Thread configuration ensures clean, smooth, low torque installation for maximumholding power.

✓ Manufactured from C1022 grade steel (premium quality) with bright zinc plating.

✓ Super sharp point dimples steel at point of contact providing wobble-free and thereforequicker installation.

✓ Deep Phillips recess reduces dropped or misaligned screws, providing fast and efficientfastening.

✓ ‘Stick fit’ gives push fit on to drywall screwdriver bit.

✓ Zinc Coating


Premium screwdriver insertbit provided in plastic bag attop of every box.

53

DRYWALLFIN

E THREAD DRYWALL


EUROPA

EN 14566

2008 = 01DW-01/14

Fine Thread Drywall Screws (Zinc)

Code Size Max Board Thickness Box Carton

DWSZ25 3.5 x 25.0 mm 15 mm 1,000 10,000

DWSZ32 3.5 x 32.0 mm 22 mm 1,000 10,000

DWSZ38 3.5 x 38.0 mm 28 mm 1,000 10,000

DWSZ42 3.5 x 42.0 mm 32 mm 1,000 10,000

DWSZ50 3.5 x 50.0 mm 40 mm 1,000 10,000

DWSZ65 4.2 x 65.0 mm 55 mm 500 5,000

DWSZ75 4.2 x 75.0 mm 65 mm 500 5,000

DWSZ90 4.8 x 90.0 mm 80 mm 500 3,000

DWSZ100 4.8 x 100.0 mm 90 mm 500 3,000

DWSZ125 4.8 x 125.0 mm 115 mm 250 2,500

DWSZ150 4.8 x 150.0 mm 140 mm 200 2,000

54 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLFINE THREAD DRYWALL

Fine Thread Drywall Screw(Black Phosphate)

Designed For: Fixing plasterboard to metal stud up to 1.2mmHead style: BugleDrive bit: Phillips 2Drill point: Super sharp pointThread form: Twin thread, fineCoating: Black phosphateShank material: Carbon steelMaterial grade: AISI C1022

✓ Black Phosphate Coating

EUROPA

EN 14566

2008 = 01DW-01/14

✓ Manufactured from C1018 grade steel (premium quality) with 48 hour salt spraytested black phosphate coating.

✓ Bugle head design for application versatility gives a flush countersink with nopaper tearing.

✓ Thread configuration ensures clean, smooth, low torque installation for maximumholding power.

✓ Super sharp point dimples steel at point of contact providing wobble-free andtherefore quicker installation.

✓ Deep Phillips recess reduces dropped or misaligned screws, providing fast andefficient fastening.

‘✓ Stick Fit’ gives push fit on to drywall screwdriver bit, which reduces dropped ormisaligned screws - less wastage.


55

DRYWALLFIN

E THREAD DRYWALL


Fine Thread Drywall Screw(Black Phosphate)

Code Size Box Carton UK Stock

EuropeanStock

DWSP25 3.5 x 25.0 mm 1,000 10,000 ✓

DWSP32 3.5 x 32.0 mm 1,000 10,000 ✓

DWSP35 3.5 x 35.0 mm 1,000 10,000 ✓

DWSP38 3.5 x 38.0 mm 1,000 10,000 ✓

DWSP42 3.5 x 42.0 mm 1,000 10,000 ✓

DWSP50 3.5 x 50.0 mm 1,000 10,000 ✓

DWSP65 4.2 x 65.0 mm 500 5,000 ✓

DWSP75 4.2 x 75.0 mm 500 5,000 ✓

DWSP100 4.8 x 100.0 mm 500 3,000 ✓

DWSP3545 3.5 x 45.0 mm 1,000 10,000 ✓

DWSP3555 3.5 x 55.0 mm 1,000 10,000 ✓

DWSP3570 3.5 x 70.0 mm 1,000 10,000 ✓

DWSP3925 3.9 x 25.0 mm 1,000 10,000 ✓

DWSP3930 3.9 x 30.0 mm 1,000 10,000 ✓

DWSP3935 3.9 x 35.0 mm 1,000 10,000 ✓

DWSP3945 3.9 x 45.0 mm 1,000 10,000 ✓

DWSP3955 3.9 x 55.0 mm 1,000 10,000 ✓

DWSP4270 4.2 x 70 mm 500 5,000 ✓

DWSP4275 4.2 x 75.0 mm 500 5,000 ✓

EUROPA

EN 14566

2008 = 01DW-01/14

IMPORTANT APPLICATION ADVICEOn rare occasions black phosphate screw coatings can react with some render types, which can damage the coating resulting incorrosion and staining. To reduce the risk of this happening Evolution recommends sealing the drywall screw heads with a PVAbonding solution before render is applied.

56 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLSELF-DRILL DRYWALL SCREWS

EUROPA

EN 14566

2008 = 01DW-01/14

Bugle Head Self-Drill Drywall Screws

Designed For: Fixing plasterboard to heavier gauge metal section (up to 2.5mm)Head style: BugleDrive bit: Phillips 2Drill point: Self drill pointThread form: TwinCoating: Electro plated zincShank material: Carbon steelMaterial grade: AISI C1022

✓ Bugle head design for application versatility gives a flushcountersink with no paper tearing.

✓ Thread configuration ensures clean, smooth, low torqueinstallation; fully formed for maximum holding power.

✓ Steel C1022 with electroplated zinc to 5µm.

✓ Self-drill point recommended for use on metal section up to2.5mm, giving fast and consistent drilling times.

✓ Deep Phillips recess reduces dropped or misaligned screws,providing fast and efficient fastening.

✓ ‘Stick fit’ gives push fit on to drywall screwdriver bit.

✓ Zinc Coating✓ Black Phosphate



57

DRYWALLSELF-D

RILL D

RYWALL S

CREWS


EUROPA

EN 14566

2008 = 01DW-01/14

Bugle Head Self-Drill Drywall Screws

Code Size Max Board Thickness Box Carton Coating UK

stockEuropean

Stock

DWSDZ25 3.5 x 25.0 mm 12 mm 1,000 10,000 Zinc ✓

DWSDZ32 3.5 x 32.0 mm 15 mm 1,000 10,000 Zinc ✓

DWSDZ38 3.5 x 38.0 mm 20 mm 1,000 10,000 Zinc ✓

DWSDZ42 3.5 x 42.0 mm 25 mm 1,000 10,000 Zinc ✓

DWSDZ50 3.5 x 50.0 mm 35 mm 1,000 10,000 Zinc ✓

DWSDZ65 4.2 x 65.0 mm 50 mm 500 5,000 Zinc ✓

DWSDZ75 4.2 x 75.0 mm 60 mm 500 5,000 Zinc ✓

DWSDZ100 4.8 x 100.0 mm 85 mm 500 3,000 Zinc ✓

DWSDZ125 4.8 x 125.0 mm 110 mm 250 2,500 Zinc ✓

DWSDZ3535 3.5 x 35.0 mm 15 mm 1,000 10,000 Zinc ✓

DWSDZ3545 3.5 x 45.0 mm 20 mm 1,000 10,000 Zinc ✓

DWSDP3525 3.5 x 25.0 mm 12 mm 1,000 10,000 BlackPhosphate ✓




58 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLSELF-DRILL DRYWALL SCREWS

EUROPA

EN 14566

2008 = 01DW-01/14

Wafer & Pan Head Self-Drill Drywall Screws

Designed For: The assembly of drywall track and ceiling track systemsDrive bit: Phillips 2Thread form: SingleCoating: Electroplated zincShank material: Carbon steelMaterial grade: AISI C1022

✓ Deep, stick-fit, Phillips recess, reduces dropped or misalignedscrews, providing fast, efficient fastening.

✓ Thread configuration ensures clean, smooth, low torqueinstallation; fully formed for maximum holding power.

✓ Superior corrosion protection to ensure long term fastenerintegrity. Electroplated zinc.

✓ Case hardened carbon steel.

✓ Super hard and sharp drill tips ensure fast drill times.

✓ Wafer Head

✓ Pan Head



59

DRYWALLSELF-D

RILL D

RYWALL S

CREWS


EUROPA

EN 14566

2008 = 01DW-01/14

Wafer & Pan Head Self-Drill Drywall Screws

Code Size Wafer Head Pan Head Box Carton

WHDZ13 4.2 x 13.0mm ✓ 1,000 10,000

WHSDZ12 4.2 x 12.0mm ✓ 1,000 10,000

WHSDZ19 4.2 x 19.0mm ✓ 1,000 10,000

WHSDZ25 4.2 x 25.0mm ✓ 1,000 10,000

WHSDZ50 4.2 x 50.0mm ✓ 500 5,000

PHSDZ12 3.9 x 12mm ✓ 1,000 10,000

60 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLCOARSE THREAD DRYWALL SCREWS

Coarse Thread Drywall Screw(Black Phosphate)

Designed For: Fixing plasterboard to timberHead style: BugleDrive bit: Phillips 2Drill point: Super sharp pointThread form: Single Coating: Black phosphateShank material: Carbon steelMaterial grade: AISI C1022


EUROPA

EN 14566

2008 = 01DW-01/14

✓ Bugle head design for application versatility gives a flush countersink with nopaper tearing.

✓ Coarse thread screws have nine threads per inch to give greater ‘grab’ in timber,as opposed to standard drywall screws which have seventeen threads per inch.

✓ Thread configuration ensures rapid advancement when fixing to timber.

✓ Deeper thread diameter of 3.65 - 3.85mm to give greater hold in timber.

✓ C1018 steel with 48 hour salt spray tested black phosphate coating.

✓ Deep Phillips recess reduces dropped or misaligned screws, providing fast andefficient fastening.

✓ ‘Stick fit’ gives push fit on to drywall screwdriver bit, which reduces dropped ormisaligned screws meaning less wastage.


61

DRYWALLCOARSE THREAD DRYWALL S

CREWS


Coarse Thread DrywallScrew (Black Phosphate)

Code Size Box Carton UK stock European Stock

DWSC25 3.5 x 25.0mm 1,000 10,000 ✓

DWSC32 3.5 x 32.0mm 1,000 10,000 ✓

DWSC38 3.5 x 38.0mm 1,000 10,000 ✓

DWSC42 3.5 x 42.0mm 1,000 10,000 ✓

DWSC50 3.5 x 50.0mm 1,000 10,000 ✓

DWSC65 4.2 x 65.0mm 500 5,000 ✓

DWSC75 4.2 x 75.0mm 500 5,000 ✓

DWSC90 4.8 x 90.0mm 500 3,000 ✓

DWSC100 4.8 x 100.0mm 500 3,000 ✓

DWSC3925 3.9 x 25 mm 1,000 10,000 ✓

DWSC3930 3.9 x 30 mm 1,000 10,000 ✓

DWSC3935 3.9 x 35 mm 1,000 10,000 ✓

DWSC3941 3.9 x 41 mm 1,000 10,000 ✓

DWSC3945 3.9 x 45 mm 1,000 10,000 ✓

DWSC3955 3.9 x 55 mm 1,000 10,000 ✓

DWSC3965 3.9 x 65 mm 1,000 10,000 ✓

DWSC4270 4.2 x 70 mm 500 5,000 ✓

DWSC4290 4.2 x 90 mm 500 5,000 ✓

DWSC48120 4.8 x 120 mm 500 5,000 ✓

DWSC5538 5.5 x 38 mm 500 5,000 ✓

EUROPA

EN 14566

2008 = 01DW-01/14


62 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLCEMENTITIOUS BOARD SCREW

Cementitious Board Screws

Designed For: Fixing cementitious and other dense boards to timber and metalsubstrates

Head style: Double countersunk with nibsRecess type: Phillips No. 2Thread type: Patent (pending) Evolution Universal ThreadMaterial: Carbon steel C1022

✓ Countersunk nibs will act to lessen reaction stresses in thesubstrate material.

✓ Countersunk nibs ensure flush finish even in very denseboard environments.

✓ High grade, medium carbon steel (C1022).

✓ Super strong neck eliminates head snap.

✓ Grey 500hr rated Evoshield TM coating gives highperforming corrosion protection, setting standards forsurface hardness and integrity.

✓ Spoon point and hi-lo threadform give rapid advancement.

✓ Self-drilling, fine thread for use in track from 0.8 to 2.5mm.

2008 = 01DW-01/14

EUROPA

EN 14566


✓ Bimetal

63

STANDARD TEKCEMENTITIOUS BOARD SCREW


Cementitious Board Screws

Code Size EvoshieldCoating Bimetal Box

WHX42 4.2 x 42 mm ✓ 200

WHX60 4.2 x 60 mm ✓ 200

WHX80 4.2 x 80 mm ✓ 200

WHX100 4.2 x 100 mm ✓ 200

BMDW4842 4.8 x 42 mm ✓ 200

BMDW4870 4.8 x 70 mm ✓ 100

EUROPA

EN 14566

2008 = 01DW-01/14

64 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLTOUGH BOARD SCREWS

Tough Board Screws

Designed For: Fixing dense and hard surfaced boards to bothdrywall track/timber base materials

Head style: CountersunkDrive bit: Phillips 2Thread form: TwinCoating: Black phosphateShank material: Carbon steelMaterial grade: AISI C1022Effective thread legth: Fully threadedDrill point: Super sharp point


EUROPA

EN 14566

2008 = 01DW-01/14

✓ Self-countersinking nibs

✓ Reduced width head

Code Size Box CartonF35 3.9 x 35.0 mm 1,000 10,000F45 3.9 x 45.0 mm 1,000 10,000

Code Size Box Carton European Stock?

DWSFCP3919 3.9 x 19.0 mm 1,000 10,000 ✓

DWSFCP3930 3.9 x 30.0 mm 1,000 10,000 ✓

DWSFCP3935 3.9 x 35.0 mm 1,000 10,000 ✓

DWSFCP3945 3.9 x 45.0 mm 1,000 10,000 ✓

Hi-Lo Tough Board Screw


65

DRYWALLHEAVY DUTY CUTTER RING DRYWALL S

CREWS


Heavy Duty Cutter Ring Drywall Screws

Designed For: Fixing fragile paper faced plasterboards to timbersubstrates

Head style: Proprietary countersunk head with undercuttingannular ring

Drive bit: Phillips No. 2Thread form: Single coarse threadFastener material: Hardened carbon steel (AISI C1022)Coating information: Electroplated zinc with clear dichromate passivation

✓ Zinc Coating

✓ Coarse single thread for use in timber substrates

✓ Countersunk head with cutting ring

✓ Super sharp point

✓ Fine single thread for use in drywall track


DWCR45 4.2 x 45.0 mm 1,000 10,000

DWSCP32 4.2 x 32.0 mm 1,000 10,000

DWSCP38 4.2 x 38.0 mm 1,000 10,000

DWSCP42 4.2 x 42.0 mm 1,000 10,000

EUROPA

EN 14566

2008 & A1: 2009

66 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLFINE THREAD COLLATED DRYWALL SCREWS

Fine Thread CollatedDrywall Screws (Zinc)

Designed for: Fixing plasterboard to metal studs of 0.5mm - 0.9mmHead style: BugleDrive bit: Phillips 2Drill point: SharpThread form: TwinCoating: Electroplated zincShank material: Carbon steelMaterial grade: AISI C1022Effective thread length: Fully threaded

✓ Zinc Coating

EUROPA

EN 14566

2008 = 01DW-01/14

✓ Double pre-sorted screws ensure 100% usability andno wasted screws

✓ Bugle head design for application versatility gives aflush countersink with no paper tearing

✓ Thread configuration ensures clean, smooth, lowtorque installation for maximum holding power

✓ Manufactured from C1022 grade steel (premiumquality) with bright zinc plating to 5µm

✓ Super sharp point dimples steel at point of contactproviding wobble-free and therefore quicker installation.


67

DRYWALLFIN

E THREAD COLLA

TED DRYWALL S

CREWS


Fine Thread CollatedDrywall Screws (Zinc)

Code Size Max BoardThickness Box Carton

CDWFZ25 3.5 x 25 mm 15 mm 1,000 10,000

CDWFZ32 3.5 x 32 mm 22 mm 1,000 10,000

CDWFZ35 3.5 x 35 mm 25 mm 1,000 10,000

CDWFZ38 3.5 x 38 mm 28 mm 1,000 10,000

CDWFZ42 3.5 x 42 mm 30 mm 1,000 10,000

CDWFZ45 3.5 x 45 mm 35 mm 1,000 10,000

CDWFZ50 3.5 x 50 mm 40 mm 1,000 10,000

CDWFZ55 3.5 x 55 mm 45 mm 1,000 10,000

CDWFZ75 4.2 x 75 mm 65 mm 500 5,000

EUROPA

EN 14566

2008 = 01DW-01/14

68 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLFINE THREAD COLLATED DRYWALL SCREWS

Fine Thread CollatedDrywall Screws (Black Phosphate)

Designed for: Fixing plasterboard to metal studs of 0.5mm - 0.9mmHead style: BugleDrive bit: Phillips 2Drill point: SharpThread form: TwinCoating: Electroplated zincShank material: Carbon steelMaterial grade: AISI C1022Effective thread length: Fully threaded

EUROPA

EN 14566

2008 = 01DW-01/14

✓ Double pre-sorted screws ensure 100% usability andno wasted screws

✓ Bugle head design for application versatility gives aflush countersink with no paper tearing

✓ Thread configuration ensures clean, smooth, lowtorque installation for maximum holding power

✓ Manufactured from C1022 grade steel (premiumquality) with bright zinc plating to 5µm

✓ Super sharp point dimples steel at point of contactproviding wobble-free and therefore quicker installation.



69

DRYWALLFIN

E THREAD COLLA

TED DRYWALL S

CREWS


Fine Thread CollatedDrywall Screws (Black Phosphate)

Code Size Box Carton UK Stock EuropeanStock

CDWFP25 3.5 x 25 mm 1,000 10,000 ✓

CDWFP35 3.5 x 35 mm 1,000 10,000 ✓

CDWFP45 3.5 x 45 mm 1,000 10,000 ✓

CDWFP55 3.5 x 55 mm 1,000 10,000 ✓

CDWFP3925 3.9 x 25 mm 1,000 10,000 ✓

CDWFP3935 3.9 x 35 mm 1,000 10,000 ✓

CDWFP3945 3.9 x 45 mm 1,000 10,000 ✓

CDWFP3955 3.9 x 55 mm 1,000 10,000 ✓

EUROPA

EN 14566

2008 = 01DW-01/14

70 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLCOARSE THREAD COLLATED DRYWALL SCREWS

Coarse Thread CollatedDrywall Screws (Black Phosphate)

Designed for: Fixing plasterboard to metal studs up to 1mmHead style: BugleDrive bit: Phillips 2Drill point: SharpThread form: TwinCoating: Black phosphateShank material: Carbon steelMaterial grade: AISI C1022Effective thread length: Fully threaded


EUROPA

EN 14566

2008 = 01DW-01/14

✓ Bugle head design for application versatility gives a flush countersink with nopaper tearing

✓ Double pre-sorted screws ensure 100% usability and no wasted screws

✓ Coarse thread screws have nine threads per inch to give greater ‘grab’ intimber, as opposed to standard drywall screws which have seventeenthreads per inch

✓ C1018/22 steel with 48 hour salt spray tested black phosphate coating

✓ Deeper thread diameter of 3.65 - 3.85mm to give greater hold in timber

✓ Super sharp ‘S’ point provides wobble free and therefore quicker installation

71

DRYWALLCOARSE THREAD COLLA

TED DRYWALL S

CREWS


Coarse Thread CollatedDrywall Screws (Black Phosphate)

Code Size Box Carton UK Stock European Stock

CDWCP25 3.5 x 25 mm 1,000 10,000 ✓

CDWCP32 3.5 x 32 mm 1,000 10,000 ✓

CDWCP35 3.5 x 35 mm 1,000 10,000 ✓

CDWCP38 3.5 x 38 mm 1,000 10,000 ✓

CDWCP42 3.5 x 42 mm 1,000 10,000 ✓

CDWCP45 3.5 x 45 mm 1,000 10,000 ✓

CDWCP50 3.5 x 50 mm 1,000 10,000 ✓

CDWCP55 3.5 x 55 mm 1,000 10,000 ✓

CDWCP65 4.2 x 65 mm 500 5,000 ✓

CDWCP75 4.2 x 75 mm 500 5,000 ✓

CDWCP3925 3.9 x 25 mm 1,000 10,000 ✓

CDWCP3930 3.9 x 30 mm 1,000 10,000 ✓

CDWCP3935 3.9 x 35 mm 1,000 10,000 ✓

CDWCP3941 3.9 x 41 mm 1,000 10,000 ✓

CDWCP3945 3.9 x 45 mm 1,000 10,000 ✓

CDWCP3955 3.9 x 55 mm 1,000 10,000 ✓

EUROPA

EN 14566

2008 = 01DW-01/14


72 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLSELF-DRILL COLLATED DRYWALL SCREWS

Self-Drill Collated Drywall Screws

Designed for: Fixing plasterboard to heavier gauge drywall track (up to 2.5mm)

Head style: BugleDrive bit: Phillips 2Drill point: Tek 1Thread form: Single thread, fineCoating: Electroplated zinc / Black PhospateShank material: Carbon steelMaterial grade: AISI C1022Fire tested: Yes, to EN1364-1Effective thread length: Fully threaded

✓ Zinc Coating✓ Black Phosphate

EUROPA

EN 14566

2008 = 01DW-01/14

✓ Bugle head design for application versatility gives a flushcountersink with no paper tearing

✓ Thread configuration ensures clean, smooth, low torqueinstallation for maximum holding power

✓ Manufactured from C1022 or C1018 grade steel (premiumquality) with bright zinc plating to 3µm

✓ #2 drill point recommended for use on metal section up to2.5mm. Faster and more consistent drilling times

✓ Double pre-sorted screws ensure 100% usability and nowasted screws

73

DRYWALLSELF-D

RILL C

OLLA

TED DRYWALL S

CREWS


Self-Drill Collated Drywall Screws

Code Size Max BoardThickness Box Carton Coating UK

StockEuropean

Stock

CDWFDZ25 3.5 x 25.0mm 15 mm 1,000 10,000 Zinc ✓




CDWSDP3525 3.5 x 25.0mm 15 mm 1,000 10,000 BlackPhosphate ✓



EUROPA

EN 14566

2008 = 01DW-01/14

74 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

DRYWALLCOLLATED TOUGH BOARD SCREWS

Collated Tough Board Screws

Designed for: Fixing dense and hard boards to track or timber substratesHead style: Reduced cross section countersunk head with undercut nibsDrive bit: Phillips No. 2Thread form: Twin hi-lo threadFastener material: Hardened carbon steel (AISI C1022)Coating information: Black phosphate (approx 48 hours NSST)


✓ Evolution collated Tough Board Screws are designed for use inan interior setting and in a dry environment. They are intendedfor fixing sheet materials harder than plasterboard, ie denseplasterboards and also to fix wood fibre boards to timberbattens and steel up to 0.8mm thick.

✓ 19mm version ideal for fitting ply to flooring before tiling.

✓ As per all collated screws, Evolution High Low Thread providessuperior pull down performance in timber and light trackapplications. Self countersinking reduced width head, PH2recess to enable standard drywall tooling.

EUROPA

EN 14566

2008 & A1: 2009

75

DRYWALLCOLLA

TED TO

UGH BOARD SCREWS


Collated Tough Board Screws

Code Size Box Carton UK Stock EuropeanStock

CDWFCP3919 3.9 x 19.0 mm 1,000 10,000 ✓

CDWFCP3930 3.9 x 30.0 mm 1,000 10,000 ✓

CDWFCP3945 3.9 x 45.0 mm 1,000 10,000 ✓

CDWFCP3935 3.9 x 35.0 mm 1,000 10,000 ✓

EUROPA

EN 14566

2008 & A1: 2009


76 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

WOODMASTER RANGEWOODMASTER SUPER CUTTER SCREWS

These Evolution Screws are CE marked and comply with EN 14592: 2009 & A1: 2012.

Double countersunk head:Improves neck strength reducing head

shearing in high torque applications.

Countersinking nibs:Enables smooth self-countersinking in both

timber and sheet material applications.The nibs cut the wood surface, trimming from

the edge of the drilled hole. The screw is driven home flush to the wood

surface every time.

Reamer shank: This helically fluted milling thread clears

drilling debris and reduces driving torque.

High quality aggressive threadform:Improves penetration and reduces driving

torque.

Deep precision formed pozi recess: Allows greater torque to be applied and

decreases the likelihood of “camming out”.

Type 17 cutting point:Aids penetration and eliminates the need to

pre-drill in almost all timbers and composites.Special long sharp point fluted to capture

chips.Eliminates splitting even when close to the

edge of the timber.No pre-drilling required in most hard woods.*Screw point takes immediate hold.

FOR UNIVERSALUSE WHENFASTENING TOWOOD, CHIPBOARD,MDF, PLASTIC ANDCOMPOSITES

Also available in torx drive versions forextra drive stability.

*Particularly dense woods may need pilot hole.

Woodmaster Super Cutter Screws

77

WOODMASTER RANGEWOODMASTER SUPER CUTTER SCREWS


Code Size Box Carton Milling Thread

Also avilable in Torx Head

WS3516 3.5 x 16mm 200 15,200 ✓

WS3520 3.5 x 20mm 200 15,200 ✓

WS3525 3.5 x 25mm 200 15,200 ✓

WS3530 3.5 x 30mm 200 15,200 ✓

WS3535 3.5 x 35mm 200 9,600WS3540 3.5 x 40mm 200 6,400 ✓

WS3550 3.5 x 50mm 200 6,400WS4020 4.0 x 20mm 200 15,200 ✓

WS4025 4.0 x 25mm 200 15,200 ✓

WS4030 4.0 x 30mm 200 9,600 ✓

WS4035 4.0 x 35mm 200 9,600WS4040 4.0 x 40mm 200 6,400 ✓

WS4050 4.0 x 50mm 200 6,400 ✓

WS4060 4.0 x 60mm 200 4,800 ✓

WS4070 4.0 x 70mm 200 4,800 ✓

WS4080 4.0 x 80mm 200 4,800 ✓

WS5030 5.0 x 30mm 200 4,800WS5040 5.0 x 40mm 200 4,800WS5050 5.0 x 50mm 200 4,800 ✓

WS5060 5.0 x 60mm 200 3,200 ✓ ✓

WS5070 5.0 x 70mm 200 3,200 ✓ ✓

WS5075 5.0 x 75mm 200 3,200 ✓

WS5080 5.0 x 80mm 200 3,200 ✓ ✓

WS5090 5.0 x 90mm 200 3,200 ✓

WS50100 5.0 x 100mm 100 2,400 ✓ ✓

WS6050 6.0 x 50mm 200 3,200WS6060 6.0 x 60mm 200 3,200 ✓

WS6070 6.0 x 70mm 200 3,200 ✓

WS6080 6.0 x 80mm 200 2,400 ✓ ✓

WS60100 6.0 x 100mm 100 2,400 ✓ ✓

WS60120 6.0 x 120mm 100 1,600 ✓ ✓

WS60150 6.0 x 150mm 100 1,200 ✓ ✓

WS60180 60 x 180mm 100 1,200 ✓

WS60200 60 x 200mm 100 800 ✓

78 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

WOODMASTER RANGEDECKING SCREWS

These Evolution Screws are CE marked and comply with EN 14592: 2009 & A1: 2012.

Flat head, c/w reaming nibs:Gives a flush, clean, attractive countersink

that locks the screw in tight.

Proprietary corrosion-resistant 1,000 hour rated green EvoshieldTMcoating:For all weather outdoor applications, from

patios, fencing, decks, walkways etc. Resistant to salt, acid, alkali, corrosive gas,

cathodic corrosion. High thermal resistance. Hydrogen embrittlement resistant.

Stainless steel variant: For use in aggressively treated timbers or

hardwoods with high tannin content.

Deep coarse thread configuration:Ensures low-torque installation, with

exceptional draw down, for maximum holdingpower.

Made from large diameter root wire forgreater shear strength.

Stick-fit, square socket recess: Reduces dropped or misaligned screws,

providing fast, efficient fastening.

Type 17 cutting point:Grabs on contact, provides rapid

advancement and means there is no need topre-drill.*

Delivers power tapping capability in all woodsand new generataion wood composites.

DESIGNED FORFIXING TIMBERDECKING ANDFENCING.

WoodmasterDecking Screws


Evoshield Coating Stainless Steel

Page 78

79

WOODMASTER RANGEDECKING SCREWS


Code Size Box Carton Drive

DSFHC50 4.2 x 50mm 200 6,000 Square



Code Size Box Carton Drive

DS-SS 50 4.2 x 50mm 200 6,000 Square

DS-SS 63 4.2 x 63mm 200 6,000 Square

DECKING SCREWS ✓ Evoshield Coating

STAINLESS STEELDECKING SCREWS

✓ 410 grade Stainless Steel

Page 79

80 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

WOODMASTER RANGESTRUCTURAL DECKING SCREWS

These Evolution Screws are CE marked and comply

with EN 14592: 2009 & A1: 2012.

1000Hr Salt Spray Rated, ACQcompatible anti-corrosion coating:To stand up to the rigours of UK weathering.

Aggressive coarse thread:Ensures highest possible withdrawal

resistance.

Type 17 cutting point:Grabs on contact, provides rapid

advancement and means there is no need topre-drill.*

Delivers power tapping capability in all woodsand new generation wood composites.


WoodmasterStructural DeckingScrews

81

WOODMASTER RANGESTRUCTURAL D

ECKING SCREWS



SDSFHC75 6.3 x 75mm 100 1,000

SDSFHC100 6.3 x 100mm 100 1,000

SDSFHC125 6.3 x 125mm 100 1,000

SDSFHC150 6.3 x 150mm 100 1,000

SDSFHC200 6.3 x 200mm 50 1,000

SDSFHC250 6.3 x 250mm 50 900

STRUCTURALDECKING SCREWS


82 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

ACCESSORIESVERTICAL FLANGE CLIPS & ACOUSTIC BRACKETS

Vertical Flange ClipsDesigned For: Fixing lighting or suspended wire to steel

profiles, cable to steel purlins or suspended ceilings to steel profiles.

Material: Carbon steelMaterial Grade: AISI C1022Coating: Yellow Zinc Passivated

Code Size Box CartonVFC43 19 x 43mm 100 1,800

✓ Fast, easy installation.✓ Series of strong barbs grip the flange.✓ Spring steel.✓ High strength.✓ Yellow zinc passivated.

Acoustic Brackets


AVAB1 70mm 100 200EVAB35 35mm 100 400

✓ Tough hangers used with timber joist ceilings/floors and ceiling systems forincreased acoustic performance.

Designed For: Use with timber joist ceilings, floorsand ceiling systems for increasedacoustic performance.

Colour: Silver GreyCoating: Electroplated Zinc

83

ACCESSORIESCLIP

S & BRACKETS


Drylining BracketsDesigned For: Fixing Drywall track to walls/ceilingsCoating: Zinc Galvanized

Code Size Box

ELG2BRA 29.5 x 195 x 0.8mm 100EGL9BRA 29.5 x 295 x 0.8mm 100

✓ Steel pressed brackets.

84 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

ACCESSORIESDRILL & DRIVE BITS

Bit HoldersDrive bit: Hex

✓ Magnetic Bit Holder


MB1060 10 x 60mm 5 20

Drive Sockets✓ Extended Magnetic Drive Socket

Code Size Box

MES5/16 5/16" x 65mm 10

Drive Kits✓ Drive Sleeve ✓ "D" end bit holder 6mm ✓ PH2 bit ✓ PH3 bit✓ Allen Key ✓ Magnetic bit holder✓ 7mm & 8mm Hex Drive sockets

Code Box

ED1000 1

85

ACCESSORIESPGM®APPROVED SDS PLUS DRILL B

ITS


PGM® Approved SDS Plus Drill BitsDesigned for: Rapid drilling of holes in masonryDrive bit: SDS Plus

Premium quality PGM® approved drill bits:✓ Extended life: typically last 33% longer than our standard SDS Plus✓ Higher performance with faster drill speed✓ Each drill is stamped with the PGM® inspection mark✓ Supplied in individual plastic sleeves for easy display

Code Size Box

SDSH55110 5.5 x 110mm 50SDSH55160 5.5 x 160mm 50SDSH6110 6.0 x 110mm 50SDSH6160 6.0 x 160mm 50SDSH6210 6.0 x 210mm 60

SDSH65160 6.5 x 160mm 50SDSH8160 8.0 x 160mm 50SDSH8210 8.0 x 210mm 50SDSH8260 8.0 x 260mm 50

SDSH10210 10.0 x 210mm 50SDSH10260 10.0 x 260mm 40SDSH12260 12.0 x 260mm 40SDSH16260 16.0 x 260mm 30

86 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

ACCESSORIESSDS PLUS DRILL BITS

SDS Plus Drill BitsDesigned for: Rapid drilling of holes in masonry.Drive bit: SDS Plus

✓ A high quality, twin fluted SDS+ carbide drill bit for the rapid drilling of holes in masonry.

✓ Designed for use with 4.8mm and 6.3mm Ø Masonry Screws✓ Supplied on individual hangers for easy display.

87

ACCESSORIESSDS PLUS DRILL B

ITS


Code Size Working Length Hex shank drive CartonSDS5110 5.0 x 110 mm 100 mm 100SDS5160 5.0 x 160 mm 100 mm 50SDS55110 5.5 x 110 mm 50 mm 100SDS55160 5.5 x 160 mm 100 mm 100SDS6110 6.0 x 110 mm 50 mm 50SDS6160 6.0 x 160 mm 100 mm 50SDS6210 6.0 x 210 mm 150 mm 50SDS6260 6.0 x 260 mm 200 mm 50SDS65110 6.5 x 110 mm 50 mm 50SDS65160 6.5 x 160 mm 100 mm 50SDS65210 6.5 x 210 mm 150 mm 50SDS65260 6.5 x 260 mm 200 mm 50SDS7160 7.0 x 160 mm 100 mm 50SDS7260 7.0 x 260 mm 200 mm 40SDS8160 8.0 x 160 mm 100 mm 50SDS8210 8.0 x 210 mm 150 mm 50SDS8260 8.0 x 260 mm 200 mm 50

SDS10160 10.0 x 160 mm 100 mm 40SDS10210 10.0 x 210 mm 150 mm 40SDS10260 10.0 x 260 mm 200 mm 40SDS10460 10.0 x 460 mm 400 mm 20SDS12160 12.0 x 160 mm 100 mm 50SDS12210 12.0 x 210 mm 150 mm 50SDS12260 12.0 x 260 mm 200 mm 35SDS12460 12.0 x 460 mm 400 mm 15SDS14260 14.0 x 260 mm 200 mm 30SDS14460 14.0 x 460 mm 400 mm 15SDS16260 16.0 x 260 mm 200 mm 25SDS16460 16.0 x 460 mm 400 mm 8SDS18260 18.0 x 260 mm 200 mm 20SDS18460 18.0 x 460 mm 400 mm 8SDS20260 20.0 x 260 mm 200 mm 15SDS20460 20.0 x 460 mm 40 mm 5

SDS435180 4.35 x 180 mm 100 mm ✓ 50SDS515180 5.15 x 180 mm 100 mm ✓ 50SDS515205 5.15 x 205 mm 125 mm ✓ 50

SDS Plus Drill Bits

88 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

ACCESSORIESSEALANTS


Intumescent and Acoustic Acrylic SealantDesigned for: Joint Filling where Fire

protection and acousticindex are an issue.

Fire tested: Yes, up to 4 hoursColour: White

✓ Evolution intumescent and acoustic sealant is a one part emulsiondesigned to resist the passage of both fire and sound. In normal usethe sealant remains flexible enough to retain the sound reductionindex of a structure. In the event of fire it will intumesce and form achar, sealing the gap for up to 4 hours.

Properties

Fire Rating Up to 4 hours

Acoustic Rating (Double Seal) Up to 48dB

Acoustic Rating (Single Seal) Up to 46dB

Movement Up to 20% of original joint size

Colour White

Slump Nil up to 20mm

Overpaintable When fully cured

Weatherability Water and UV resistant when fully cured

Drying Time Tack free in 15 minutes

Cure Time 1.5mm per 24 hours

Joint Size Linear Metres Per Cartridge

6x 10mm 5.2

10 x 10mm 3.1

15 x 15mm 1.4

20 x 15mm 1.0

30 x 15mm 0.7

Code Size Acoustic Rating (Double Seal)

Acoustic Rating (Single Seal) Box

EVIA310 310 ml up to 48 dB up to 48 dB 25 tubes

EVIA900 900 ml up to 46 dB up to 46 dB 12 tubes

89

ACCESSORIESTEK COLOUR CAPS


Tek Colour Caps PC8-16 PC8-19 PC8-29 PC8-32


PC8-16 16mm UV Protected Colour Cap 1,000 10,000

PC8-19 19mm UV Protected Colour Cap 1,000 10,000

PC8-29 29mm Protected Colour Cap 1,000 10,000

PC8-32 32mm Protected Colour Cap 1,000 10,000

NOTE: COLOURCHARTS ARE FORGUIDANCE ONLY. IF UNFAMILIARWITH THECOLOURS PLEASE CONTACT US FOR A SAMPLE.

90 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

COATINGSCOATINGS

Evoshield®

What is Evoshield®?Evoshield® is our trademarked fastener coating. It is a non-organic, tri-layered ceramicsurface coating developed to attain optimum performance in the various pollutive andatmospheric conditions that cause corrosion.

Layer 1: metallic zincLayer 2: ceramic layerLayer 3: resin layer

The distinguishing feature of Evoshield® is the tight joining of the baked resin layer andthe ceramic layer thanks to the cross-linking effect. These layers are bonded togetherwith the metallic zinc layer through chemical reactions, and this unique method ofcombining layers results in a rigid and dense combination of the coating films.Evoshield® treatment does not attribute its anti-corrosion properties to merely a singlematerial, but the synergy of these three layers, which combined have superb rustproofqualities.

Compatible with metal coated and painted surfaces, fasteners coated with Evoshield®are resistant to acid and alkaline attack, galvanic corrosion and hydrogen embrittlement.These fasteners conform to corrosive gas test standard (Kesternich) DIN50018 and givea salt spray fog test to exceed (JISZ2731) 1,000 hours (ASTM B117).

Benefits of Evoshield®✓ Available with 500hr/1,000hr hour salt spray rating (please refer to the relevant

datasheet for details of the salt spray rating of a specific product or call or email us)✓ Superior corrosion resistance. Excellent against gas, weathering and other corrosive

factors including salt water ✓ Resistant to acid and alkaline attack, galvanic corrosion and hydrogen embrittlement✓ Corrosion resistance against scratches. Composite layers minimise the effect of

scratches on the protection coating✓ Electrolytic corrosion resistance. Less contact corrosion with other metals✓ Low process temperature. The drying temperature below 200ºC protects the

products from metallographic changes✓ Paintable✓ Available in a variety of colours

Blue Evoshield®

Green Evoshield®

Silver Evoshield®

Grey Evoshield®


COATINGSCOATINGS

ZincEvolution Fasteners utilises specialist zinc coatings in the protection of our products.Our electroplated zinc coatings are designed to give sacrificial protection to thefasteners in an electrogalvanic corrosion scenario as well as resistance to corrosion(tested to BS EN ISO 9227: 2012).

In addition to pure zinc coatings, we use specialist coatings such as zinc with yellowdi-chromate passivation to give additional resistance to corrosion and chemical attack.

Stainless SteelEvolution Fasteners use 300 series austenitic stainless steels in our fasteners wherethe ultimate in corrosion resistance is demanded by the application. These screws areconstructed from SAE 304 (Euro Class A2) stainless steel.

In addition to this, we offer a limited range of 400 series martensitic stainless steelswhere screws may be subjected to higher temperatures. These screws areconstructed from SAE 408 and 410 stainless steel.

TESTINGEvolution Fasteners test all of our screws and coatings to the

highest possible standards in our own in-house testing laboratory. Our primary method is through Neutral Salt Spray Testing to

BS EN ISO 9227: 2012 but we also subject our coatings to testing in acid, alkalis, solvents and organics to ensure that the coatings we supply

are of premium quality.

92

CE MARKING

Page 92

On the 1st of July 2013, European Regulation No. 305/2011 (commonlyreferred to as the Construction Products Regulations) came into full force.It completely repealed European Directive 89/106/EEC (commonlyreferred to as the Construction Products Directive).

Unlike the Directive, the Regulation will be legally mandated across allMember States of the European Union.

There are legal requirements placed upon Manufacturers, Importers andDistributors of construction products.

Most notably is the requirement to CE mark products.

CE Marking is only required on a product which falls within the scope of a HarmonisedEuropean Standard (EN). A list of such standards is maintained on the EU-LEX (the EuropeanCommissions’ website) and in the OJEU (Official Journal of the European Union).

Where there is such a harmonised standard, the product must undergo both ITT (Initial TypeTesting) and FPC (Factory Production Control); which can take the form of an audited QualityManagement System (such as ISO 9001: 2009) so long as it takes into considerationmanufacturing, quality and technical considerations unique to the product being CE marked.

The steps and requirements for ITT and FPC are outlined in the EN which covers the product.As such, the requirements change for every individual product.

Other products that do not require mandatory CE markingunder an EN may still be adorned with the CE mark. This

route is by ETA (European Technical Assessment),which can be derived by testing and documentation

to either an ETAG (European TechnicalAssessment Guideline) or CUAP (CommonUnderstanding of Assessment Procedure). Ineither case, the testing must be performed byan accredited laboratory and thedocumentation must be drawn up andratified by EOTA (European Organisation forTechnical Approvals) via a Notified Body.

Whether a product is being CE marked byan EN or ETA, the end document whichallows the CE mark to be adorned is knownas the DoP (Declaration of Performance).This document details critical compliance,conformity and performance informationand is the manufacturers’ own legaldeclaration document.

CE MARKING

7485

Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

Copyright © 2013 Evolution Fasteners (UK) Ltd. All rights reserved.

To assist you in the promotion ofevolution products, we are happy toprovide display stands with initialproduct orders.

Designed to suit you and yourcustomers’ requirements, they willprovide a professional image helpingto promote sales and improve the use of valuable space.

DISPLAY STANDS FOREVOLUTIONPRODUCTS

T: +44 (0)141 647 7100E: [email protected]

CALL TOORDER TODAY!

www.evolutionfasteners.co.uk

94 Tel: +44 (0)141 647 7100 Fax: +44 (0)141 647 5100

GENERAL

1. (a) All orders placed with Evolution Fasteners UK Ltd (hereinafterreferred to as ‘The Company’) are subject to the terms andconditions set out below. No modifications or variations to theseterms and conditions and no other terms and conditions shallbe valid or effective unless expressly accepted in writing by aDirector of the Company.

(b) Any subsequent orders placed with the Company shall bedeemed to be placed s u b j e c t to these terms and conditionsunless expressly agreed otherwise in writing by a Director of theCompany.

QUOTATIONS

2. A quotation by the Company does not constitute an offer and theCompany reserves the right to withdraw or amend the same at anytime prior to the Company’s acceptance of the Purchaser’s order.The Buyers purchase order is binding and the Buyer is responsiblefor costs arising from any changes of nature to the order.

PRICE

3. The price of any goods shall be the Company’s list price of the goodsprevailing at the date of acceptance of the order by the Company(less any agreed discount).

4. Unless otherwise stated all prices are exclusive of V.A.T.

5. The Company shall be entitled from time to time to vary list price orlist prices without prior notice.

PAYMENT

6. Unless otherwise specified in writing by the seller, payment is dueon or before the end of the month following that in which the goodswere invoiced.

7. Failure by the Buyer to pay for any goods on the due date shallentitle the Company:

(a) to cancel the balance (if any) of the contract under which theBuyer has failed to pay for the goods and to recover from theBuyer damages for any loss suffered by the Company as aresult of such cancellation, and/or

(b) to cancel any other contract or the balance of any other contractwhich the Company may have with the Buyer and to recoverfrom the Buyer damages for any loss suffered by the Companyas a result of such cancellation, and/or

(c) to charge the Buyer interest at the rate of 2.5% per monthcalculated on a day-to-day basis on the amount due from thedate of invoice to the date of actual payment thereof (bothbefore and after any judgement) such interest to be paid ondemand.

ACCOUNTS

8. The Company reserves the right to close a credit account at any timewithout prior notice whereupon the whole of the amount outstandingon such account shall become immediately due and payable in full.

COLLECTION AND DELIVERY

9. Where the Company agrees to deliver any goods to the Buyer:

(a) The Buyer shall pay the Company’s delivery charges thereforeat the rate or rates prevailing at the date of acceptance of theorder by the Company or at such other rate or rates as may beagreed between the Company and the Buyer prior to the dateof acceptance of the order by the Company.

(b) Delivery of the goods shall be made to such place or places asagreed between the Company and the Buyer.

(c) The Buyer will ensure that there is adequate access to the placeof delivery and that there is made available at the place ofdelivery adequate labour and other facilities in order to enablethe goods to be unloaded promptly and safely and the Buyerwill indemnify the Company in respect of any losses costs andexpenses incurred by the Company as a consequence thereofand (without prejudice to the generality of the foregoing) theCompany shall be entitled to charge the Buyer for the storageof the goods whether at the Company’s premises or otherwise.

(d) If the Buyer shall refuse for any reason whatsoever to acceptdelivery of the goods the Buyer will indemnify the Company inrespect of all losses costs and expenses incurred by theCompany as a consequence thereof and (without prejudice tothe generality of the foregoing) the Company shall be entitledto charge the Buyer for the storage of the goods whether at theCompany’s premises or otherwise.

(e) The Company shall be entitled to make part deliveries of thegoods and for the purposes of these terms and conditions eachsuch part delivery shall be treated as a separate andindependent contract for the sale of goods to the Buyer.

10. (a) Any times stated for collection or delivery shall be a bona fideestimate only and whilst the Company will use all reasonableendeavours to meet any such times stated the Company shallnot be liable for any delay howsoever caused.

(b) Where no times are stated for collection or delivery theCompany will use all reasonable endeavours to make the goodsavailable for collection or to deliver the goods (as the case maybe) as soon as reasonably practicable.

(c) The Company shall be entitled to stop collection by or towithhold delivery to the Buyer of any goods where at the timecollection or delivery payment is due to the Company in respectof any goods supplied to the Buyer under any contractwhatsoever.

DAMAGE OR LOSS IN TRANSIT

11. Where the Company is responsible for delivering the goods tothe Buyer the Company will at its option repair or replace freeof charge any goods lost or damaged in transit provided that:

(a) (save in respect of a total loss or non-delivery of the goods)

details of any loss or damage have been marked on the copyof the consignment note or delivery documents signed by theBuyer and advised to the Company within 48 hours of deliveryand confirmed in writing to the Company with full particularswithin 3 days of delivery, and

(b) in respect of a total loss or non- delivery of the goods detailsare advised to the Company in writing (otherwise than on aconsignment note or delivery document) with full particularswithin (7 days) of the date of the Company’s invoice in respectof the goods.

SHORT DELIVERY

12. The Company shall not be responsible for any short deliveryunless details thereof are marked on the consignment note ordelivery document signed by the Buyer and in the case of lossin transit all the requirements set out in Condition 10(b) aboveare fulfilled.

STORAGE

13. Where the Company has notified the Buyer that the goods are readyfor delivery, the Buyer shall take delivery or arrange for storage. Ifthe Buyer does not so take delivery or arrange for storage within 7days of notification the Company shall be entitled to invoice and bepaid for the goods as though the goods had been duly delivered inaccordance with these instructions and the Company may arrangestorage either at the Company’s own premises or elsewhere on theBuyer’s behalf and all charges for storage, insurance and demurrageshall be payable by the Buyer.

DEFECTIVE GOODS

14. The Company shall at their option repair or replace any goodswhich are defective as to materials or workmanship providedthat:

(a) where any alleged defect is discoverable on an inspection ofthe goods (whether or not the Buyer shall actually inspect thegoods) notification of the alleged defect with full particularsthereof is received by the Company in writing within 7 days ofthe date of collection or delivery of the goods and in any othercase notification of the alleged defect is received by theCompany in writing with full particulars thereof within 10 daysof the date of collection or delivery of the goods, and

(b) the Company is notified in writing with full particularsimmediately upon discovery of the allegeddefect and is affordedthe opportunity of inspecting the goods at the premises of theBuyer or if so required by the Company the Buyer immediatelyreturns the goods to the Company’s premises carriage paid (butrefundable insofar as the goods are repaired or replaced), and

(c) any defect is not due to wear and tear neglect abnormal usemisuse or improper adjustment.

(d) The Company shall not be liable for transportation or installationcharges, for expense of the Buyers for repairs or replacementsor for damages for delay or loss of use or other indirect,incidental or consequential damage of any kind.

15. (a) As against a person dealing as a consumer as definedby Section 12 of the Unfair Contract Terms Act 1977 allconditions and warranties and liabilities whatsoeverwhether express or implied by statute (save thoseimplied by virtue of Sections 12 to 15 of the Sale ofGoods Act 1979) common law usage or otherwise arehereby excluded.

(b) As against a person dealing otherwise than as a consumer asdefined by Section 12 of the Unfair Contract Terms Act 1977 theprovisions contained in Condition 12 above shall be acceptedin substitution for and to the entire exclusion of all conditionsand warranties and liabilities whatsoever whether express orimplied by statute (save those implied by virtue of Section 12 ofthe Sale of Goods Act 1979) common law usage or otherwise.

16. Save and except as expressly stated in Conditions 12 and 13above the Company shall not be liable for any defect in thegoods or for any injury or loss resulting from the goods or anydefect therein or from any work done in connection therewithwhether such liability is due to the negligence of any servantemployee or agent of the Company or otherwise.

17. In the event that the Company shall be liable to repair or replacethe goods, in no circumstances shall the Company’s liabilityextend beyond the cost of repair or replacing the goods. In anyevent, notwithstanding anything contained in the contract, in nocircumstances shall the Company be liable in contract, tort(including negligence or breach of statutory duty) or otherwisehowsoever and whatsoever the cause thereof:

i. For any increased costs or expensesii. For any loss or profit, business contracts, revenues or

anticipated savings oriii. For any special direct or consequential damage of any nature

whatsoever said to have occurred consequent on the supply orthe circumstances of the supply of the goods or services hereincontracted to be supplied by the company or any subcontractorto its customer.

RETURNED GOODS

18. (a) Where returned Goods are found to be damaged due tothe Buyer’s fault the Buyer will be liable for the cost ofremedying such damage

(b) The vendor will not accept goods for credit or rectification unlesssuch return has been pre- authorised by Evolution FastenersUK Ltd, and the goods are received by the vendor in stockcondition, with original packaging and the vendor retains theright at its sole discretion whether to accept the return of thegoods or whether to rectify the goods or whether to issue acredit note in respect thereof.

(c) The purchaser shall unless otherwise stated be responsible forthe cost of outward and return carriage and insurance of allgoods returned by the purchaser to the vendor for service orcredit which goods shall be at the risk of the purchaser untilactual receipt of the goods by the vendor. The onus of proof of

safe delivery shall rest with the purchaser.(d) All items returned to the vendor by prearrangement and found

to contain no fault, will be subject to a 30% restocking charge,providing the goods are in original stock condition. Anydownward variation of this restocking charge shall be at the solediscretion of the vendor.

(e) No credit shall be allowed for goods until they have beenreceived complete.

FORCE MAJEURE

19. (a) The Company shall not be responsible for any loss damagedelay or non- performance of any contract arising whetherdirectly or indirectly from any cause outside the control of theCompany including (but without prejudice to the generality ofthe foregoing) any cause arising from or attributable to strikelock-out shortage of labour or materials governmental actioncivil commotion riots wars sabotage storm flood earthquakedrought machinery breakdown failure of plant collapse ofstructures voluntary or mandatory compliance with any directionrequest or order of any person having or appearing to haveauthority whether for defence or other governmental or nationalpurposes inability to obtain raw materials equipment fuel powercomponents or transportation.

(b) In the event of any delay or non- performance of any contractarising whether directly or indirectly from any cause referred toin Condition 19(a) above the Company shall be entitled tocancel any contract without payment to the buyer in respect ofany loss or damage or otherwise.

PROPERTY AND RISK

20. Property in any goods sold shall not pass to the Buyeruntil all sums outstanding from the Buyer to the Companywhether in respect of the goods or for any other reasonwhatsoever have been paid in full by the Buyer.

21. Notwithstanding that property in any goods sold may nothave passed to the Buyer the goods shall be at the riskof the Buyer from the time they are loaded onto thetransport vehicle at the Company’s premises or otherplace of storage of the goods save that where theCompany has agreed to deliver the goods to the Buyerthe goods shall be at the risk of the Buyer from themoment they are unloaded from the transport vehicle atthe place of delivery.

22. (a) The ownership of the goods shall only be transferred tothe buyer when the buyer has paid the full price for thegoods and other goods ordered by the buyer deliveredby the Company (including where applicable interest onany sums not paid on the due date) and until suchpayment is made the goods are held by the Buyer asBailee for the Company.

(b) If the Buyer shall sell or purport to sell the goods so as to purportto pass a valid title to a third party, the proceeds of such saleshall be held by the buyer on trust for the company and if suchproceeds are not paid to the company they shall be placed in aseparate Designated bank account.

(c) The goods shall be stored by the buyer in a safe and propermanner and in such a way so as to distinguish them from goodsnot owned by the Company and shall be separately identifiedin such manner as approved or directed by the Company.

d) Until payment of the whole price has been made by the buyerto the company (including interest where applicable) theCompany shall have the right to require the immediate return ofthe goods and be granted a Licence to enter the buyer’spremises or any premises where the goods are being kept orare thought by the company to be kept, and to remove thegoods.

(e) The right to trace any goods, the price of which remains unpaidor any proceeds of the purported sale of such goods intowhomsoever’s hands the same may pass is expressly reservedto the company.

(f) Each and every sub-clause of this clause shall be deemed tobe separate from the remainder of the contract and severableaccordingly.

GOVERNING LAW AND JURISDICTION

23. All contracts between the Company and the Buyer shallin respects be governed by English Law and all disputeswhich may arise out of or in connection with theseConditions or any contract between the Company andthe Buyer or any goods supplied or to be supplied underany contract shall be subject to the exclusive jurisdictionof the English Courts save that the Company shall be atliberty to bring any legal proceedings against the Buyerin the Courts of any other country which it considersappropriate.

24. In the event that the Company shall bring any legalproceedings against the Buyer in connection with theseConditions or any contract between the Company andthe Buyer or any goods supplied or to be supplied underthe contract the Buyer shall indemnify the Companyagainst all costs and expenses incurred by the Companyin connection therewith on a full indemnity basis.

25. For the avoidance of doubt nothing in these trading termsand conditions are intended to confer on any third partyany benefit or the right to enforce any terms within theconditions.

TERMS AND CONDITIONS OF SALE

Visit our websitewww.evolutionfasteners.co.uk

for latest product information, offers and Evolution news

Sales and Customer ServiceTel: +44 (0) 141 647 7100Fax: +44 (0) 141 647 5100

Email: [email protected]

Administration and AccountsTel: +44 (0) 20 8905 2759Fax: +44 (0) 20 8207 0044

Copyright © 2014 Evolution Fasteners (UK) Ltd. All rights reserved.

Documents

Evolution Fasteners Product Guide 2015 - PRE RELEASE EDITION