8/22/2019 Even Flow 400

1/4

Evenflow C&D LLCEVENFLOW C&D LLC

Make a Positive Impact! Page 2

400 S E R I E S C E R A M I C S

The 400 Series products are the next level ofhigh performance, thin film, andceramic technology. WP 400 P roducts provide high solids Ceramic technology inthin film applications, with ambient cure, where maximum wear and performance isrequired. The tight matrixes ofthe 400 Series products are unsurpassed inthermal, abrasion, wear and corrosion resistance. Because ofthe complexity of the400 Series, insome cases aprimer may benecessary toadhere to certainsubstrates, but is required when a repair or re-coat is necessary. The 400 Series isavailable in avariety offinishes from high gloss clear, satin, matte, heatdissipative, orthermal barrier applications.

1. 400 Series Coatings provide awide range ofapplication solutions.Beginning with corrosion resistance, toheat transfer, mold release, and thermalbarriers. 400products can beapplied from .5 to 5.0microns depending onformula.Color Clear to opaque depending on formulaViscosity

8/22/2019 Even Flow 400

2/4

E VE NFLOW C&D LLCMake a Positive Impact!

400 " S e r i e s " Na n o -Cer a m i c T h i n F il m T ech n o l o g yS ca l a b l e Ce ra mi c Coat ing Capab i l i t i e s :-Proven Nano-Ceramic "Thin Film" Technology (~.25 to 5.0microns)-Light, Flexible, Clear and Permanent Surface P rotection-Improve performance and Longevity of most metal, synthetic, and composite surfaces-Low Coefficient of Friction .04-.08 micron depending onsurface-Reduce IceBuild-Up inHigh A ltitude or Freezing environments-Abrasion Resistant-Corrosion Resistance from salt water and other environmental and chemical degradation-More resilient than anyother clear coating on themarket-Flexible-Reduce repair and replacement ofsurface coatings-Reduce fouling and build up of residue (aircraft and small watercraft)-P rotect from Skydrol, J P-8Fuel, brake fluid, andmost other aircraft and engine lubricants/fluids-P rotect metal,chrome and other alloys from heat burns-P rotect Electronic C ircuit Boards from heat, tinwhiskers, water, corrosion, short circuits

-Reapplication without removing previous coat-No Silicone-V.O.C. Free-Found to increase lift by20+% (tested on, smooth, efficient wing design)-Drag reduced by1% (tested on, smooth, efficient wing design)

A ll information contained herein should be deemed proprietary and confidential and should be protected as such.

Evenflow C&D L L C , O'Fa l l on , MO 63366636.328.4418, Em : GolfandRich(2)vahoo.com

8/22/2019 Even Flow 400

3/4

EVENFLOW C&D LLCMake a Positive Impact!

W P 490 SeriesT H E R M A L B A R R I E R

W P 490 Thermal B a r r i e r products are designed for long term protection andperformance. WP490 offers non-rigid high heat protection from indirect or direct flame.WP490 thin fi lm ranges from 0.5-1.5 mils thick and offers excellent chemical andweather durability. Temperature may be reduced by as much as 4 0 + % , (substratedependent). WP 490 Thermal Barrier is applicable to a wide range of markets andproject requirements. Our "Nano" Technologies enable WP 490 Thermal Barriers tobe a cost effective solution in today's market.W P 490 Thermal B a r r i e r is used in the fol lowing types of applications:1. Internal Combustion Engines2. Aerospace Components3. Composite panels and parts4 . Industrial duct and pipe systems5. Electronic components6. Fire & Safety Applications7. Insulation & Energy Systems

W P 490 Thermal B a r r i e r is a two component material, designed for easy of applicationon a wide variety of surfaces and materials. Metal, Fiberglass, Carbon Fiber composites,Ceramics, Plastics and other synthetics. Designed as an ambient (air cure) system.Coating may reduce radiant heat by as much as 40+%.W P 490 cure cycles can be accelerated w i th the use of an oven or IR system i f needed.Standard or electro-static spray systems are recommended for uniform coatingapplication.

Evenflow C & D L L C , 636.328.4418, Em: GolfandRich@yahoo.com

8/22/2019 Even Flow 400

4/4

EVENFLOW C&D LLCMake a Positive Impact!

MX 490 Se r i e sTherm a l Bar r i e r Coa t

SPECIFICATION:

> Q-UV (ASTM D 4587-01) 2000+ Hours> Q-FOG (ASTM B 117-03) 5% so lu t ion 2000+ Hours> ADHE SION (ASTM D 3359-02) 5B> HAR DNES S (ASTM D 3363-00) 7H *Ambient cure*> HEAT STABILITY 1600F+> CO NICAL BEND (AST M D 522-93a) 1/8"> IMPACT DIRE CT (ASTM D 2794-93) 120lbs> IMP AC T INDIRE CT (ASTM D 2794-93) 100IDS> SOLIDS BY WEIGHT 65-70% 2% (by formula)> VISC OS ITY (#2 ZAHN C UP ) 17secs/ 185cps@77F> AVERAGE THICKNESS ( S u b s t r a t e D e p e n d e n t ) .75 mil (19 microns)> THEORETICAL COVERAGE 1200ft2 @ 1mil(25 microns)> H.M.I.S. 1.2.1.B> V.O.C. (ASTM D 3960-04) O.OIbs per gal> FULL CURE AMBIENT TEMP 5 Days 75F**> Color Opaque (color will vary per formula and customer need)

* Physical properties will increase with elevated temperature and pressure cures.

* * Acce le ra ted c u r e c y c l e s for MX 490Allow coated parts to air dry for 2 hours at 75F (dry to touch). P lace parts in curing oven, ramp temperature up to350F. Once part substrate has reached temperature, cure parts for minimum of1 hour.All information contained in this document is deemed true and accurate to the best of our knowledge and testing.We recommend that you make adequate test and assessments to determine the suitability of this product for yourneeds.