Upload
zambosen
View
41
Download
1
Tags:
Embed Size (px)
DESCRIPTION
European Structural Sections of Steel. Suitable for structural engineers, architects and etc.
Citation preview
Corus Construction & Industrial
Structural sections
in accordance with European specifications
13502 Corus Euro Cover.qxd 22/3/06 10:37 am Page 2
Structural sections in accordance with European specifications
Corus Construction & Industrial 1Corus Construction & Industrial 1
Table des matieres
PageNotations 2Nuances et Présentation 3Dimensions et Propriétés
Profilés IPE 4-7Profilés HE 8-13
Cornières à Ailes Egales 14-15Cornières à Ailes Inégales 16-17Tolérances de Laminage
BS EN 10034: 1993 18-19BS EN 10056 – 2: 1993 20
Bureaux de Vente Corus 27-28
InhaltBezeichnung 2Stahlsorten und Qualität 3Querschnittsgrössen
IPE Profile Gemäß Euronorm 4-7Profils HE Gemäß Euronorm 8-13
Gleichschenkliger Winkelstahl 14-15Ungleichschenkliger Winkelstahl 16-17Walztoleranzen
BS EN 10034: 1993 21-22BS EN 10056 – 2: 1993 23
Corus Verkaufbüros 27-28
ContentsNotation 2Quality and Presentation 3Dimensions and Properties
IPE Beams 4-7HE Wide Flange Beams 8-13
Equal Angles 14-15Unequal Angles 16-17Rolling Tolerances
BS EN 10034: 1993 24-25BS EN 10056 – 2: 1993 26
Offices and Agents for Corus Exports 27-28
13502 Corus Euro Inners 21/3/06 6:04 pm Page 1
Structural sections in accordance with European specifications
2 Corus Construction & Industrial
Notationsen conformitéavec EN 1993-1-1A = Section d’acier
b = Largeur du profilé
d = Hauteur de la portion droite
de l’âme
G = Poids par mètre courant
h = Hauteur du profilé
hw = Hauteur intérieure entre ailes
I = Moment d’inertie
i = Rayon de giration
IT = Moment d’inertie de torsion
Iω = Facteur de gauchissement
par rapport au centre de
cisaillement
Iyz = Moment centrifuge
r,r1 = Rayon de congé
r2 = Rayon de congé extérieur
t = Epaisseur
t f = Epaisseur d’aile
t w = Epaisseur d’âme
W = Module de flexion élastique
Wpl = Module de flexion plastique
ys = Distance du centre de
gravité suivant l’axe y
zs = Distance du centre de
gravité suivant l’axe z
Il incombe à l’utilisateur de
vérifier selon la nuance d’acier si
les valeurs des élancements de
l’âme et des ailes du profil choisi
satisfont aux conditions
d’application des règles de
dimensionnement utilisées.
Bezeichnungenlaut EN 1993-1-1
A = Querschnittsfläche
b = Profilbreite
d = Höhe des geraden
Stegteils
G = Gewicht pro lfd. Meter
h = Profilhöhe
hw = Innere Höhe zwischen
Flanschen
I = Flächenmoment
i = Trägheitsbalbmesser
IT = Torsionsflächenmoment
Iω = Wölbflächenmoment
bezogen auf den
Schubmittelpunkt
Iyz = Flächenzentrifugalmoment
r,r1 = Ausrundungsradius
r2 = Abrundungsradius
t = Stärke
t f = Flanschdicke
t w = Stegdicke
W = Elastisches
Widerstandsmoment
Wpl = Plastisches
Widerstandsmoment
ys = Schwerpunktsabstand in
Richtung y-Achse
zs = Schwerpunktsabstand in
Richtung z-Achse
Es solte geprüft werden, ob die
Schlankheitsgrade von Steg und
Flansch des ausgesuchten Profils
den in den Anwendebestimmungen
der Baunormen in Abhängigkeit
der Stahlsorten angegebenen
Werte entsprechen.
Notationsaccording toEN 1993-1-1
A = Sectional area
b = Width of section
d = Depth of straight portion
of web
G = Weight per metre
h = Depth of section
hw = Inner depth between flanges
I = Moment of inertia
i = Radius of gyration
IT = Torsional constant
Iω = Warping constant referred
to the shear centre
Iyz = Centrifugal moment
r,r1 = Radius of root fillet
r2 = Toe radius
t = Thickness
t f = Flange thickness
t w = Web thickness
W = Elastic section modulus
Wpl = Plastic section modulus
ys = Distance of centre of gravity
along y-axis
zs = Distance of centre of gravity
along z-axis
Designers should verify that the
slenderness ratios of web and
flange of the chosen section and
grade comply with the design
codes used.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 2
Structural sections in accordance with European specifications
Corus Construction & Industrial 3
Nuances, tolérances etprésentation
Nuances d’acier
Nuances d’acier de construction
conformément aux normes nationales et
internationales:
(Grades S235JR, S275JR, S275J0,
S275J2 et S355JR, S355J0, S355J2),
ASTM A36, A572 et JIS.
Tolérances de laminage
Sur les dimensions, les profilés, le
poids et la longueur conformes à
Euronorm, BS EN10034: 1993 et BS
EN10056-2: 1993.
Longueurs
De 6m à 24m. Pour certaines tailles, il
est possible de fournir des longueurs
jusqu’à 27m sur demande spéciale.
Finitions
Les profilés sont normalement fournis
tels quels à l’état laminé, mais on peut
sur demande passer le matériau à la
grenaille et le recouvrir d’un apprêt ou
de peinture.
Marquage
Tous les profiles seront identifiés par
une étiquette code barre Corus
standard.
Stahlsorten, toleranzen undqualität
Stahlsorten
Stahlsorten gemäss Nationalen und
Internationalel Normen:
(Grades S235JR, S275JR, S275J0,
S275J2 et S355JR, S355J0, S355J2),
ASTM A36, A572 und JIS.
Walztoleranzen
Mass, Profile, Gewicht und Länge in
Euronorm, BS EN10034: 1993 und BS
EN10056-2: 1993.
Längen
Von 6 bis 24m. Bestimmte Grössen bis
27m stehen zur Verfügung nach
Vereinbarung.
Oberflächen
Profile werden normalerweise “wie
gewalzt” geliefert, auf Wunsch kann das
Material auch gestrahlt und konserviert
werden.
Kennzeichnung
Alle Träger werden durch unsere mit Bar
Code versehenen Standard Corus
Etiketten gekennzeichnet.
Steel grades, tolerancesand presentation
Steel grades
Structural steel grades in accordance
with national and international
standards:
(Grades S235JR, S275JR, S275J0,
S275J2 et S355JR, S355J0, S355J2),
ASTM A36, A572 and JIS.
Rolling tolerances
On dimensions, profile, weight and
length to Euronorm, BS EN10034: 1993
and BS EN10056-2: 1993.
Lengths
From 6m up to 24m. For certain sizes
lengths up to 27m may be supplied by
arrangement.
Finishes
Sections are normally supplied in the
as-rolled condition but arrangements
can be made for material to be shot-
blasted and primed/painted.
Marking
All sections will be identified using the
standard Corus bar coded label.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 3
Structural sections in accordance with European specifications
4 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
IPE 100 A
IPE 100
IPE 120 A
IPE 120
IPE 140 A
IPE 140
IPE 140 R
IPE 160 A
IPE 160
IPE 160 R
IPE 180 A
IPE 180
IPE 180 O
IPE 180 R
IPE 200 A
IPE 200
IPE 200 O
IPE 200 R
IPE 220 A
IPE 220
IPE 220 O
IPE 220 R
IPE 240 A
IPE 240
IPE 240 O
IPE 240 R
IPE 270 A
IPE 270
IPE 270 O
IPE 270 R
IPE 300 A
IPE 300
IPE 300 O
IPE 300 R
G
kg/m
6.89
8.10
8.66
10.4
10.5
12.9
14.4
12.7
15.8
17.7
15.4
18.8
21.3
22.1
18.4
22.4
25.1
26.6
22.2
26.2
29.4
31.6
26.2
30.7
34.3
37.3
30.7
36.1
42.3
44.0
36.5
42.2
49.3
51.7
h
mm
98
100
118
120
137
140
142
157
160
162
177
180
182
183
197
200
202
204
217
220
222
225
237
240
242
245
267
270
274
276
297
300
304
306
b
mm
55
55
64
64
73
73
72
82
82
81
91
91
92
89
100
100
102
98
110
110
112
108
120
120
122
118
135
135
136
133
150
150
152
147
t w
mm
3.6
4.1
3.8
4.4
3.8
4.7
5.3
4.0
5.0
5.6
4.3
5.3
6.0
6.4
4.5
5.6
6.2
6.6
5.0
5.9
6.6
6.7
5.2
6.2
7.0
7.5
5.5
6.6
7.5
7.7
6.1
7.1
8.0
8.5
t f
mm
4.7
5.7
5.1
6.3
5.6
6.9
7.8
5.9
7.4
8.5
6.5
8.0
9.0
9.5
7.0
8.5
9.5
10.5
7.7
9.2
10.2
11.8
8.3
9.8
10.8
12.3
8.7
10.2
12.2
13.1
9.2
10.7
12.7
13.7
r
mm
7
7
7
7
7
7
7
9
9
9
9
9
9
9
12
12
12
12
12
12
12
12
15
15
15
15
15
15
15
15
15
15
15
15
A
cm2
8.78
10.3
11.0
13.2
13.4
16.4
18.3
16.2
20.1
22.6
19.6
23.9
27.1
28.1
23.5
28.5
32.0
33.9
28.3
33.4
37.4
40.2
33.3
39.1
43.7
47.5
39.1
45.9
53.8
56.0
46.5
53.8
62.8
65.9
hw d
mm mm
88.6 74.6
88.6 74.6
107.4 93.4
107.4 93.4
126.2 112.2
126.2 112.2
126.2 112.2
145.2 127.2
145.2 127.2
145.2 127.2
164.0 146.0
164.0 146.0
164.0 146.0
164.0 146.0
183.0 159.0
183.0 159.0
183.0 159.0
183.0 159.0
201.6 177.6
201.6 177.6
201.6 177.6
201.6 177.6
220.4 190.4
220.4 190.4
220.4 190.4
220.4 190.4
249.6 219.6
249.6 219.6
249.6 219.6
249.6 219.6
278.6 248.6
278.6 248.6
278.6 248.6
278.6 248.6
Poutrelles à ailes à facesparallèles de la série Européenne conformes à Euronorme 19-57
Europäische I-trägermit parallelen Flanschflächen gemaß Euronorm 19-57
European specification beamswith parallel flanges in accordance with Euronorm 19-57
t w
y
bz
h
r
y
t f
z
d h w
Bezeichnungen Seite 2 Explanation page 2
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 4
Structural sections in accordance with European specifications
Corus Construction & Industrial 5
Explanation page 2
Désignation
Bezeichnung
Section
IPE 100 A
IPE 100
IPE 120 A
IPE 120
IPE 140 A
IPE 140
IPE 140 R
IPE 160 A
IPE 160
IPE 160 R
IPE 180 A
IPE 180
IPE 180 O
IPE 180 R
IPE 200 A
IPE 200
IPE 200 O
IPE 200 R
IPE 220 A
IPE 220
IPE 220 O
IPE 220 R
IPE 240 A
IPE 240
IPE 240 O
IPE 240 R
IPE 270 A
IPE 270
IPE 270 O
IPE 270 R
IPE 300 A
IPE 300
IPE 300 O
IPE 300 R
Iy Iz
cm4
cm4
141 13.1
171 15.9
257 22.4
318 27.7
435 36.4
541 44.9
609 48.8
689 54.4
869 68.3
992 75.7
1063 81.9
1317 101
1505 117
1554 112
1591 117
1943 142
2211 169
2363 166
2317 171
2772 205
3134 240
3481 249
3290 240
3892 284
4369 329
4823 339
4917 358
5790 420
6947 513
7300 516
7173 519
8356 604
9994 746
10500 728
iy iz
cm cm
4.01 1.22
4.07 1.24
4.83 1.42
4.90 1.45
5.70 1.65
5.74 1.65
5.76 1.63
6.53 1.83
6.58 1.84
6.62 1.83
7.37 2.05
7.42 2.05
7.45 2.08
7.44 2.00
8.23 2.23
8.26 2.24
8.32 2.30
8.35 2.21
9.05 2.46
9.11 2.48
9.16 2.53
9.30 2.49
9.94 2.68
9.97 2.69
10.0 2.74
10.1 2.67
11.2 3.02
11.2 3.02
11.4 3.09
11.4 3.03
12.4 3.34
12.5 3.35
12.6 3.45
12.6 3.32
Wy Wz
cm3
cm3
28.8 4.77
34.2 5.79
43.8 7.00
53.0 8.65
63.3 9.98
77.3 12.3
86.0 13.5
87.8 13.3
109 16.7
122 18.7
120 18.0
146 22.2
165 25.5
170 25.2
162 23.4
194 28.5
219 33.1
232 33.8
214 31.2
252 37.3
282 42.8
309 46.1
278 40.0
324 47.3
361 53.9
394 57.4
368 53.0
429 62.2
507 75.5
529 77.6
483 69.2
557 80.5
658 98.1
686 99.0
Wply Wplz
cm3
cm3
33.0 7.52
39.4 9.13
49.9 11.0
60.7 13.6
71.6 15.5
88.4 19.2
99.0 21.3
99.1 20.7
124 26.1
140 29.3
135 27.9
166 34.6
189 39.9
195 39.6
182 36.5
221 44.5
249 51.8
265 53.1
240 48.4
285 58.0
321 66.8
352 71.8
312 62.3
367 73.8
410 84.3
450 90.0
413 82.2
484 96.8
575 118
601 121
542 107
628 125
744 152
780 154
Iω IT
dm6
cm4
0.0003 0.727
0.0004 1.16
0.0007 0.996
0.0009 1.69
0.0016 1.34
0.0020 2.40
0.0022 3.36
0.0031 1.93
0.0040 3.54
0.0045 5.06
0.0060 2.67
0.0075 4.73
0.0088 6.65
0.0084 7.63
0.0106 4.14
0.0131 6.92
0.0156 9.36
0.0155 11.7
0.0188 5.68
0.0228 9.03
0.0269 12.2
0.0283 16.4
0.0314 8.50
0.0376 13.0
0.0439 17.1
0.0459 22.8
0.0597 10.4
0.0708 15.9
0.0880 25.0
0.0890 29.1
0.107 13.3
0.126 19.9
0.158 31.0
0.155 37.0
Poutrelles à ailes à facesparallèles de la série Européenne conformes à Euronorme 19-57
Europäische I-trägermit parallelen flanschflächen gemaß Euronorm 19-57
European specification beamswith parallel flanges in accordance with Euronorm 19-57
Bezeichnungen Seite 2Notation page 2
G
kg/m
6.89
8.10
8.66
10.4
10.5
12.9
14.4
12.7
15.8
17.7
15.4
18.8
21.3
22.1
18.4
22.4
25.1
26.6
22.2
26.2
29.4
31.6
26.2
30.7
34.3
37.3
30.7
36.1
42.3
44.0
36.5
42.2
49.3
51.7
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 5
Structural Sections in accordance with European Specifications
6 Corus Construction & Industrial
Structural Sections in accordance with European Specifications
Notation page 2
Désignation
Bezeichnung
Section
IPE 330 A
IPE 330
IPE 330 O
IPE 330 R
IPE 360 A
IPE 360
IPE 360 O
IPE 360 R
IPE 400 A
IPE 400
IPE 400 O
IPE 400 R
IPE 400 V
IPE 450 A
IPE 450
IPE 450 O
IPE 450 R
IPE 450 V
IPE 500 A
IPE 500
IPE 500 O
IPE 500 R
IPE 500 V
IPE 550 A
IPE 550
IPE 550 O
IPE 550 R
IPE 550 V
IPE 600 A
IPE 600
IPE 600 O
IPE 600 R
IPE 600 V
IPE 750 X 137
IPE 750 X 147
IPE 750 X 161
IPE 750 X 173
IPE 750 X 185
IPE 750 X 196
IPE 750 X 210
IPE 750 X 222
G
kg/m
43.0
49.1
57.0
60.3
50.2
57.1
66.0
70.4
57.4
66.3
75.7
81.5
84.0
67.2
77.6
92.4
95.2
104
79.4
90.7
107
111
129
92.1
106
123
134
159
108
122
154
144
184
137
147
160
174
185
197
210
222
h
mm
327
330
334
336
358
360
364
367
397
400
404
407
408
447
450
456
458
460
497
500
506
508
514
547
550
556
560
566
597
600
610
608
618
753
753
758
762
766
770
775
778
b
mm
160
160
162
158
170
170
172
168
180
180
182
178
182
190
190
192
188
194
200
200
202
198
204
210
210
212
210
216
220
220
224
218
228
263
265
266
267
267
268
268
269
t w
mm
6.5
7.5
8.5
9.2
6.6
8.0
9.2
9.9
7.0
8.6
9.7
10.6
10.6
7.6
9.4
11.0
11.3
12.4
8.4
10.2
12.0
12.6
14.2
9.0
11.1
12.7
14.0
17.1
9.8
12.0
15.0
14.0
18.0
11.5
13.2
13.8
14.4
14.9
15.6
16.0
17.0
t f
mm
10.0
11.5
13.5
14.5
11.5
12.7
14.7
16.0
12.0
13.5
15.5
17.0
17.5
13.1
14.6
17.6
18.6
19.6
14.5
16.0
19.0
20.0
23.0
15.7
17.2
20.2
22.2
25.2
17.5
19.0
24.0
23.0
28.0
17.0
17.0
19.3
21.6
23.6
25.4
28.0
29.5
r
mm
18
18
18
18
18
18
18
18
21
21
21
21
21
21
21
21
21
21
21
21
21
21
21
24
24
24
24
24
24
24
24
24
24
17
17
17
17
17
17
17
17
A
cm2
54.7
62.6
72.6
76.8
64.0
72.7
84.1
89.7
73.1
84.5
96.4
104
107
85.5
98.8
118
121
132
101
116
137
142
164
117
134
156
170
202
137
156
197
184
234
175
187
204
221
236
251
268
283
hw d
mm mm
307.0 271.0
307.0 271.0
307.0 271.0
307.0 271.0
334.6 298.6
334.6 298.6
334.6 298.6
334.6 298.6
373.0 331.0
373.0 331.0
373.0 331.0
373.0 331.0
373.0 331.0
420.8 378.8
420.8 378.8
420.8 378.8
420.8 378.8
420.8 378.8
468.0 426.0
468.0 426.0
468.0 426.0
468.0 426.0
468.0 426.0
515.6 467.6
515.6 467.6
515.6 467.6
515.6 467.6
515.6 467.6
562.0 514.0
562.0 514.0
562.0 514.0
562.0 514.0
562.0 514.0
719.0 685.0
719.0 685.0
719.4 685.4
718.8 684.8
718.8 684.8
719.2 685.2
719.0 685.0
719.0 685.0
Poutrelles à ailes à facesparallèles de la série Européenne conformes à Euronorme 19-57
Europäische I-trägermit parallelen Flanschflächen gemaß Euronorm 19-57
European specification beamswith parallel flanges in accordance with Euronorm 19-57
Bezeichnungen Seite 2 Explanation page 2
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 6
Structural Sections in accordance with European Specifications
Corus Construction & Industrial 7
Explanation page 2
Désignation
Bezeichnung
Section
IPE 330 A
IPE 330
IPE 330 O
IPE 330 R
IPE 360 A
IPE 360
IPE 360 O
IPE 360 R
IPE 400 A
IPE 400
IPE 400 O
IPE 400 R
IPE 400 V
IPE 450 A
IPE 450
IPE 450 O
IPE 450 R
IPE 450 V
IPE 500 A
IPE 500
IPE 500 O
IPE 500 R
IPE 500 V
IPE 550 A
IPE 550
IPE 550 O
IPE 550 R
IPE 550 V
IPE 600 A
IPE 600
IPE 600 O
IPE 600 R
IPE 600 V
IPE 750 X 137
IPE 750 X 147
IPE 750 X 161
IPE 750 X 173
IPE 750 X 185
IPE 750 X 196
IPE 750 X 210
IPE 750 X 222
G
kg/m
43.0
49.1
57.0
60.3
50.2
57.1
66.0
70.4
57.4
66.3
75.7
81.5
84.0
67.2
77.6
92.4
95.2
104
79.4
90.7
107
111
129
92.1
106
123
134
159
108
122
154
144
184
137
147
160
174
185
197
210
222
Iy Iz
cm4
cm4
10230 685
11770 788
13910 960
14690 958
14520 944
16270 1043
19050 1251
20360 1270
20290 1171
23130 1318
26750 1564
28860 1606
30140 1766
29760 1502
33740 1676
40920 2085
42400 2070
46200 2397
42930 1939
48200 2142
57780 2622
59930 2600
70720 3271
59980 2432
67120 2668
79160 3224
86600 3447
102300 4265
82920 3116
92080 3387
118300 4521
110300 3993
141600 5570
159900 5166
166100 5289
186100 6073
205800 6873
223000 7510
240300 8175
262200 9011
278200 9604
iy iz
cm cm
13.7 3.54
13.7 3.55
13.8 3.64
13.8 3.53
15.1 3.84
15.0 3.79
15.0 3.86
15.1 3.76
16.7 4.00
16.5 3.95
16.7 4.03
16.7 3.93
16.8 4.06
18.7 4.19
18.5 4.12
18.6 4.21
18.7 4.13
18.7 4.26
20.6 4.38
20.4 4.31
20.6 4.38
20.5 4.28
20.8 4.47
22.6 4.55
22.3 4.45
22.5 4.55
22.5 4.50
22.5 4.60
24.6 4.77
24.3 4.66
24.5 4.79
24.5 4.66
24.6 4.88
30.3 5.44
29.8 5.31
30.2 5.45
30.5 5.57
30.8 5.65
31.0 5.71
31.3 5.80
31.3 5.82
Wy Wz
cm3
cm3
626 85.6
713 98.5
833 119
874 121
812 111
904 123
1047 145
1111 151
1022 130
1156 146
1324 172
1418 180
1477 194
1331 158
1500 176
1795 217
1851 220
2009 247
1728 194
1928 214
2284 260
2360 263
2752 321
2193 232
2441 254
2847 304
3093 328
3616 395
2778 283
3069 308
3879 404
3629 366
4582 489
4246 393
4411 399
4909 457
5402 515
5821 563
6241 610
6765 672
7152 714
Wply Wplz
cm3
cm3
702 133
805 153
943 185
995 190
907 172
1019 191
1186 227
1265 236
1144 202
1308 229
1503 269
1618 283
1682 304
1495 245
1702 276
2047 341
2115 346
2302 389
1946 301
2195 335
2613 408
2710 414
3169 506
2475 361
2788 400
3264 480
3563 520
4206 632
3142 441
3513 485
4472 639
4176 580
5325 780
4865 614
5110 631
5666 719
6218 810
6691 884
7174 959
7762 1054
8225 1122
Iω IT
dm6
cm4
0.172 19.6
0.200 28.1
0.247 42.2
0.247 50.6
0.283 27.4
0.315 37.4
0.382 55.7
0.390 68.8
0.434 36.2
0.492 51.3
0.590 73.3
0.611 92.5
0.673 99.6
0.707 47.1
0.794 66.7
1.00 109
0.999 123
1.16 149
1.13 64.3
1.25 89.1
1.55 143
1.55 162
1.97 242
1.72 89.3
1.89 123
2.31 187
2.49 242
3.12 372
2.62 122
2.86 165
3.88 316
3.42 271
4.85 506
7.00 135
7.16 157
8.28 208
9.42 270
10.3 334
11.3 406
12.6 512
13.5 601
Poutrelles à ailes à facesparallèles de la série Européenne conformes à Euronorme 19-57
Europäische I-trägermit parallelen Flanschflächen gemaß Euronorm 19-57
European specification beamswith parallel flanges in accordance with Euronorm 19-57
Bezeichnungen Seite 2Notation page 2
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 7
Structural sections in accordance with European specifications
8 Corus Construction & Industrial8 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
HE 100 AA
HE 100 A
HE 100 B
HE 120 AA
HE 120 A
HE 120 B
HE 140 AA
HE 140 A
HE 140 B
HE 160 AA
HE 160 A
HE 160 B
HE 160 M
HE 180 AA
HE 180 A
HE 180 B
HE 180 M
HE 200 AA
HE 200 A
HE 200 B
HE 200 M
HE 220 AA
HE 220 A
HE 220 B
HE 220 M
HE 240 AA
HE 240 A
HE 240 B
HE 240 M
HE 260 AA
HE 260 A
HE 260 B
HE 260 M
G
kg/m
12.2
16.7
20.4
14.6
19.9
26.7
18.1
24.7
33.7
23.8
30.4
42.6
76.2
28.7
35.5
51.2
88.9
34.6
42.3
61.3
103
40.4
50.5
71.5
117
47.4
60.3
83.2
157
54.1
68.2
93.0
172
h
mm
91
96
100
109
114
120
128
133
140
148
152
160
180
167
171
180
200
186
190
200
220
205
210
220
240
224
230
240
270
244
250
260
290
b
mm
100
100
100
120
120
120
140
140
140
160
160
160
166
180
180
180
186
200
200
200
206
220
220
220
226
240
240
240
248
260
260
260
268
t w
mm
4.2
5.0
6.0
4.2
5.0
6.5
4.3
5.5
7.0
4.5
6.0
8.0
14.0
5.0
6.0
8.5
14.5
5.5
6.5
9.0
15.0
6.0
7.0
9.5
15.5
6.5
7.5
10.0
18.0
6.5
7.5
10.0
18.0
t f
mm
5.5
8.0
10.0
5.5
8.0
11.0
6.0
8.5
12.0
7.0
9.0
13.0
23.0
7.5
9.5
14.0
24.0
8.0
10.0
15.0
25.0
8.5
11.0
16.0
26.0
9.0
12.0
17.0
32.0
9.5
12.5
17.5
32.5
r
mm
12
12
12
12
12
12
12
12
12
15
15
15
15
15
15
15
15
18
18
18
18
18
18
18
18
21
21
21
21
24
24
24
24
A
cm2
15.6
21.2
26.0
18.6
25.3
34.0
23.0
31.4
43.0
30.4
38.8
54.3
97.1
36.5
45.3
65.3
113
44.1
53.8
78.1
131
51.5
64.3
91.0
149
60.4
76.8
106
200
69.0
86.8
118
220
hw d
mm mm
80 56
80 56
80 56
98 74
98 74
98 74
116 92
116 92
116 92
134 104
134 104
134 104
134 104
152 122
152 122
152 122
152 122
170 134
170 134
170 134
170 134
188 152
188 152
188 152
188 152
206 164
206 164
206 164
206 164
225 177
225 177
225 177
225 177
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen Flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2 Explanation page 2
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 8
Structural sections in accordance with European specifications
Corus Construction & Industrial 9Corus Construction & Industrial 9
Explanation page 2
Désignation
Bezeichnung
Section
HE 100 AA
HE 100 A
HE 100 B
HE 120 AA
HE 120 A
HE 120 B
HE 140 AA
HE 140 A
HE 140 B
HE 160 AA
HE 160 A
HE 160 B
HE 160 M
HE 180 AA
HE 180 A
HE 180 B
HE 180 M
HE 200 AA
HE 200 A
HE 200 B
HE 200 M
HE 220 AA
HE 220 A
HE 220 B
HE 220 M
HE 240 AA
HE 240 A
HE 240 B
HE 240 M
HE 260 AA
HE 260 A
HE 260 B
HE 260 M
G
kg/m
12.2
16.7
20.4
14.6
19.9
26.7
18.1
24.7
33.7
23.8
30.4
42.6
76.2
28.7
35.5
51.2
88.9
34.6
42.3
61.3
103
40.4
50.5
71.5
117
47.4
60.3
83.2
157
54.1
68.2
93.0
172
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2Notation page 2
Iy Iz
cm4
cm4
237 92.1
349 134
450 167
413 159
606 231
864 318
719 275
1033 389
1509 550
1283 479
1673 616
2492 889
5098 1759
1967 730
2510 925
3831 1363
7483 2580
2944 1068
3692 1336
5696 2003
10640 3651
4170 1510
5410 1955
8091 2843
14600 5012
5835 2077
7763 2769
11260 3923
24290 8153
7981 2788
10450 3668
14920 5135
31310 10450
iy iz
cm cm
3.89 2.43
4.06 2.51
4.16 2.53
4.72 2.93
4.89 3.02
5.04 3.06
5.59 3.45
5.73 3.52
5.93 3.58
6.50 3.97
6.57 3.98
6.78 4.05
7.25 4.26
7.34 4.47
7.45 4.52
7.66 4.57
8.13 4.77
8.17 4.92
8.28 4.98
8.54 5.07
9.00 5.27
9.00 5.42
9.17 5.51
9.43 5.59
9.89 5.79
9.83 5.87
10.1 6.00
10.3 6.08
11.0 6.39
10.8 6.36
11.0 6.50
11.2 6.58
11.9 6.90
Wy Wz
cm3
cm3
52.0 18.4
72.8 26.8
89.9 33.5
75.8 26.5
106 38.5
144 52.9
112 39.3
155 55.6
216 78.5
173 59.8
220 76.9
312 111
566 212
236 81.1
294 103
426 151
748 277
317 107
389 134
570 200
967 354
407 137
515 178
736 258
1217 444
521 173
675 231
938 327
1799 657
654 214
836 282
1148 395
2159 780
Wply Wplz
cm3
cm3
58.4 28.4
83.1 41.1
104 51.3
84.2 40.6
120 58.8
165 80.9
124 59.9
174 84.8
245 120
191 91.2
245 117
354 170
675 325
258 123
325 156
482 231
884 425
347 163
430 204
643 306
1135 543
446 209
569 270
827 394
1420 678
571 264
745 351
1054 498
2117 1006
715 327
920 430
1283 602
2524 1192
Iω IT
dm6
cm4
0.0017 2.33
0.0026 5.28
0.0034 9.33
0.0043 2.59
0.0065 6.04
0.0094 13.9
0.0102 3.43
0.0151 8.10
0.0225 20.2
0.0238 6.43
0.0315 12.1
0.0480 31.3
0.108 161
0.0464 8.31
0.0603 14.9
0.0939 42.2
0.200 201
0.0846 12.5
0.108 21.0
0.171 59.7
0.347 258
0.146 15.5
0.194 28.6
0.296 77.0
0.574 313
0.240 22.1
0.329 42.1
0.488 104
1.15 626
0.383 30.1
0.517 54.2
0.755 127
1.73 720
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 9
Structural sections in accordance with European specifications
10 Corus Construction & Industrial10 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
HE 280 AA
HE 280 A
HE 280 B
HE 280 M
HE 300 AA
HE 300 A
HE 300 B
HE 300 M
HE 320 AA
HE 320 A
HE 320 B
HE 320 M
HE 340 AA
HE 340 A
HE 340 B
HE 340 M
HE 360 AA
HE 360 A
HE 360 B
HE 360 M
HE 400 AA
HE 400 X 107
HE 400 A
HE 400 B
HE 400 M
HE 450 AA
HE 450 X 123
HE 450 A
HE 450 B
HE 450 M
HE 500 AA
HE 500 A
HE 500 B
HE 500 M
G
kg/m
61.2
76.4
103
189
69.8
88.3
117
238
74.2
97.6
127
245
78.9
105
134
248
83.7
112
142
250
92.4
107
125
155
256
99.7
124
140
171
263
107
155
187
270
h
mm
264
270
280
310
283
290
300
340
301
310
320
359
320
330
340
377
339
350
360
395
378
384
390
400
432
425
435
440
450
478
472
490
500
524
b
mm
280
280
280
288
300
300
300
310
300
300
300
309
300
300
300
309
300
300
300
308
300
297
300
300
307
300
300
300
300
307
300
300
300
306
t w
mm
7.0
8.0
10.5
18.5
7.5
8.5
11.0
21.0
8.0
9.0
11.5
21.0
8.5
9.5
12.0
21.0
9.0
10.0
12.5
21.0
9.5
10.0
11.0
13.5
21.0
10.0
10.2
11.5
14.0
21.0
10.5
12.0
14.5
21.0
t f
mm
10.0
13.0
18.0
33.0
10.5
14.0
19.0
39.0
11.0
15.5
20.5
40.0
11.5
16.5
21.5
40.0
12.0
17.5
22.5
40.0
13.0
16.0
19.0
24.0
40.0
13.5
18.5
21.0
26.0
40.0
14.0
23.0
28.0
40.0
r
mm
24
24
24
24
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
A
cm2
78.0
97.3
131
240
88.9
113
149
303
94.6
124
161
312
101
133
171
316
107
143
181
319
118
136
159
198
326
127
158
178
218
335
137
198
239
344
hw d
mm mm
244 196
244 196
244 196
244 196
262 208
262 208
262 208
262 208
279 225
279 225
279 225
279 225
297 243
297 243
297 243
297 243
315 261
315 261
315 261
315 261
352 298
352 298
352 298
352 298
352 298
398 344
398 344
398 344
398 344
398 344
444 390
444 390
444 390
444 390
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen Flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2 Explanation page 2
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 10
Structural sections in accordance with European specifications
Corus Construction & Industrial 11Corus Construction & Industrial 11
Explanation page 2
Désignation
Bezeichnung
Section
HE 280 AA
HE 280 A
HE 280 B
HE 280 M
HE 300 AA
HE 300 A
HE 300 B
HE 300 M
HE 320 AA
HE 320 A
HE 320 B
HE 320 M
HE 340 AA
HE 340 A
HE 340 B
HE 340 M
HE 360 AA
HE 360 A
HE 360 B
HE 360 M
HE 400 AA
HE 400 X 107
HE 400 A
HE 400 B
HE 400 M
HE 450 AA
HE 450 X 123
HE 450 A
HE 450 B
HE 450 M
HE 500 AA
HE 500 A
HE 500 B
HE 500 M
G
kg/m
61.2
76.4
103
189
69.8
88.3
117
238
74.2
97.6
127
245
78.9
105
134
248
83.7
112
142
250
92.4
107
125
155
256
99.7
124
140
171
263
107
155
187
270
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen Flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2Notation page 2
Iy Iz
cm4
cm4
10560 3664
13670 4763
19270 6595
39550 13160
13800 4734
18260 6310
25170 8563
59200 19400
16450 4959
22930 6985
30820 9239
68130 19710
19550 5185
27690 7436
36660 9690
76370 19710
23040 5410
33090 7887
43190 10140
84870 19520
31250 5861
37640 6998
45070 8564
57680 10820
104100 19340
41890 6088
55860 8338
63720 9465
79890 11720
131500 19340
54640 6314
86970 10370
107200 12620
161900 19150
iy iz
cm cm
11.6 6.85
11.9 7.00
12.1 7.09
12.8 7.40
12.5 7.30
12.7 7.49
13.0 7.58
14.0 8.00
13.2 7.24
13.6 7.49
13.8 7.57
14.8 7.95
13.9 7.18
14.4 7.46
14.6 7.53
15.6 7.90
14.7 7.12
15.2 7.43
15.5 7.49
16.3 7.83
16.3 7.06
16.6 7.16
16.8 7.34
17.1 7.40
17.9 7.70
18.2 6.92
18.8 7.27
18.9 7.29
19.1 7.33
19.8 7.59
20.0 6.79
21.0 7.24
21.2 7.27
21.7 7.46
Wy Wz
cm3
cm3
800 262
1013 340
1376 471
2551 914
976 316
1260 421
1678 571
3482 1252
1093 331
1479 466
1926 616
3796 1276
1222 346
1678 496
2156 646
4052 1276
1359 361
1891 526
2400 676
4297 1268
1654 391
1960 471
2311 571
2884 721
4820 1260
1971 406
2568 556
2896 631
3551 781
5501 1260
2315 421
3550 691
4287 842
6180 1252
Wply Wplz
cm3
cm3
874 399
1113 518
1535 717
2966 1396
1066 481
1384 640
1870 869
4079 1912
1197 505
1629 709
2150 938
4436 1950
1342 528
1851 755
2409 985
4718 1952
1496 552
2089 801
2684 1032
4990 1942
1825 599
2166 721
2563 872
3233 1103
5571 1933
2184 624
2837 849
3217 965
3983 1197
6332 1938
2577 648
3950 1058
4815 1291
7095 1931
Iω IT
dm6
cm4
0.591 35.5
0.786 63.5
1.13 146
2.52 807
0.879 47.8
1.20 87.8
1.69 189
4.39 1411
1.04 53.6
1.51 112
2.07 230
5.01 1506
1.23 60.0
1.83 131
2.46 263
5.60 1512
1.45 67.1
2.18 153
2.89 298
6.15 1513
1.95 81.3
2.37 126
2.95 193
3.82 361
7.43 1520
2.58 91.4
3.62 178
4.15 250
5.27 448
9.28 1534
3.31 103
5.65 318
7.03 548
11.2 1544
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 11
Structural sections in accordance with European specifications
12 Corus Construction & Industrial12 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
HE 550 AA
HE 550 A
HE 550 B
HE 550 M
HE 600 AA
HE 600 x 137
HE 600 x 151
HE 600 x 174
HE 600 A
HE 600 B
HE 600 M
HE 650 AA
HE 650 A
HE 650 B
HE 650 M
HE 700 AA
HE 700 X 166
HE 700 A
HE 700 B
HE 700 M
HE 800 AA
HE 800 A
HE 800 B
HE 800 M
HE 900 AA
HE 900 A
HE 900 B
HE 900 M
HE 1000 AA
HE 1000 A
HE 1000 B
HE 1000 M
G
kg/m
120
166
199
278
129
137
151
175
178
212
285
138
190
225
293
150
166
204
241
301
172
224
262
317
198
252
291
333
222
272
314
349
h
mm
522
540
550
572
571
575
582
588
590
600
620
620
640
650
668
670
678
690
700
716
770
790
800
814
870
890
900
910
970
990
1000
1008
b
mm
300
300
300
306
300
300
300
300
300
300
305
300
300
300
305
300
300
300
300
304
300
300
300
303
300
300
300
302
300
300
300
302
t w
mm
11.5
12.5
15.0
21.0
12.0
11.8
11.6
13.6
13.0
15.5
21.0
12.5
13.5
16.0
21.0
13.0
12.5
14.5
17.0
21.0
14.0
15.0
17.5
21.0
15.0
16.0
18.5
21.0
16.0
16.5
19.0
21.0
t f
mm
15.0
24.0
29.0
40.0
15.5
17.5
20.6
23.9
25.0
30.0
40.0
16.0
26.0
31.0
40.0
17.0
21.0
27.0
32.0
40.0
18.0
28.0
33.0
40.0
20.0
30.0
35.0
40.0
21.0
31.0
36.0
40.0
r
mm
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
30
30
30
30
30
30
30
30
30
30
30
30
A
cm2
153
212
254
354
164
175
193
223
226
270
364
176
242
286
374
191
212
260
306
383
218
286
334
404
252
321
371
424
282
347
400
444
hw d
mm mm
492 438
492 438
492 438
492 438
540 486
540 486
540 486
540 486
540 486
540 486
540 486
588 534
588 534
588 534
588 534
636 582
636 582
636 582
636 582
636 582
734 674
734 674
734 674
734 674
830 770
830 770
830 770
830 770
928 868
928 868
928 868
928 868
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen Flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2 Explanation page 2
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 12
Structural sections in accordance with European specifications
Corus Construction & Industrial 13
Explanation page 2
Désignation
Bezeichnung
Section
HE 550 AA
HE 550 A
HE 550 B
HE 550 M
HE 600 AA
HE 600 x 137
HE 600 x 151
HE 600 x 174
HE 600 A
HE 600 B
HE 600 M
HE 650 AA
HE 650 A
HE 650 B
HE 650 M
HE 700 AA
HE 700 X 166
HE 700 A
HE 700 B
HE 700 M
HE 800 AA
HE 800 A
HE 800 B
HE 800 M
HE 900 AA
HE 900 A
HE 900 B
HE 900 M
HE 1000 AA
HE 1000 A
HE 1000 B
HE 1000 M
G
kg/m
120
166
199
278
129
137
151
175
178
212
285
138
190
225
293
150
166
204
241
301
172
224
262
317
198
252
291
333
222
272
314
349
Poutrelles à larges ailes à facesparallèles de la série Européenne conformes à Euronorme 53-62
Europäische warmgewalze breite I-trägermit parallelen Flanschflächen gemaß Euronorm 53-62
European wide flange beamsin accordance with Euronorm 53-62
Bezeichnungen Seite 2Notation page 2
Iy Iz
cm4
cm4
72870 6767
111900 10820
136700 13080
198000 19160
91870 6993
101500 7893
117100 9287
136400 10780
141200 11270
171000 13530
237400 18980
113900 7221
175200 11720
210600 13980
281700 18980
142700 7673
168900 9471
215300 12180
256900 14440
329300 18800
208900 8134
303400 12640
359100 14900
442600 18630
301100 9041
422100 13550
494100 15820
570400 18450
406500 9501
553800 14000
644700 16280
722300 18460
iy iz
cm cm
21.8 6.65
23.0 7.15
23.2 7.17
23.6 7.35
23.7 6.53
24.1 6.72
24.7 6.94
24.7 6.95
25.0 7.05
25.2 7.08
25.6 7.22
25.5 6.41
26.9 6.97
27.1 6.99
27.5 7.13
27.3 6.34
28.2 6.69
28.8 6.84
29.0 6.87
29.3 7.01
30.9 6.10
32.6 6.65
32.8 6.68
33.1 6.79
34.6 5.99
36.3 6.50
36.5 6.53
36.7 6.60
38.0 5.80
40.0 6.35
40.1 6.38
40.3 6.45
Wy Wz
cm3
cm3
2792 451
4146 721
4971 872
6923 1252
3218 466
3529 526
4024 619
4639 719
4787 751
5701 902
7660 1244
3676 481
5474 782
6480 932
8433 1245
4260 512
4982 631
6241 812
7340 963
9198 1237
5426 542
7682 843
8977 994
10870 1230
6923 603
9485 903
10980 1054
12540 1222
8380 633
11190 934
12890 1085
14330 1222
Wply Wplz
cm3
cm3
3128 698
4623 1106
5591 1340
7934 1936
3624 724
3953 813
4484 952
5203 1108
5351 1155
6426 1390
8773 1930
4161 750
6137 1204
7321 1441
9658 1935
4841 799
5599 977
7033 1256
8328 1494
10540 1928
6226 855
8701 1311
10230 1552
12490 1929
8000 957
10810 1413
12590 1657
14440 1928
9778 1015
12830 1469
14860 1715
16570 1939
Iω IT
dm6
cm4
4.35 127
7.20 360
8.87 610
13.6 1559
5.40 142
6.13 177
7.32 247
8.57 374
9.00 407
11.0 677
16.0 1570
6.59 158
11.0 458
13.4 749
18.7 1584
8.18 186
10.2 274
13.4 522
16.1 839
21.5 1595
11.5 243
18.3 609
21.9 959
27.9 1657
16.3 322
25.0 749
29.6 1150
34.9 1683
21.4 387
32.2 835
37.8 1267
43.2 1713
t w
y
bz
h
r
y
t f
z
d h w
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 13
Structural sections in accordance with European specifications
14 Corus Construction & Industrial14 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
L 90 x 90 x 6
L 90 x 90 x 8
L 90 x 90 x 10
L 90 x 90 x 12
L 100 x 100 x 8
L 100 x 100 x 10
L 100 x 100 x 12
L 100 x 100 x 15
L 120 x 120 x 8
L 120 x 120 x 10
L 120 x 120 x 12
L 120 x 120 x 15
L 150 x 150 x 10
L 150 x 150 x 12
L 150 x 150 x 15
L 150 x 150 x 18
L 200 x 200 x 16
L 200 x 200 x 18
L 200 x 200 x 20
L 200 x 200 x 24
G
kg/m
8.3
10.9
13.4
15.9
12.2
15.0
17.8
21.9
14.7
18.2
21.6
26.6
23.0
27.3
33.8
40.1
48.5
54.2
59.9
71.1
h
mm
90
90
90
90
100
100
100
100
120
120
120
120
150
150
150
150
200
200
200
200
b
mm
90
90
90
90
100
100
100
100
120
120
120
120
150
150
150
150
200
200
200
200
t
mm
6
8
10
12
8
10
12
15
8
10
12
15
10
12
15
18
16
18
20
24
r1
mm
11
11
11
11
12
12
12
12
13
13
13
13
16
16
16
16
18
18
18
18
r2
mm
5.5
5.5
5.5
5.5
6.0
6.0
6.0
6.0
6.5
6.5
6.5
6.5
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
zs
cm
2.41
2.50
2.58
2.66
2.74
2.82
2.90
3.02
3.23
3.31
3.40
3.51
4.03
4.12
4.25
4.37
5.52
5.60
5.68
5.84
ys
cm
2.41
2.50
2.58
2.66
2.74
2.82
2.90
3.02
3.23
3.31
3.40
3.51
4.03
4.12
4.25
4.37
5.52
5.60
5.68
5.84
A
cm2
10.6
13.9
17.1
20.3
15.5
19.2
22.7
27.9
18.7
23.2
27.5
33.9
29.3
34.8
43.0
51.0
61.8
69.1
76.3
90.6
Cornières à ailes égalesconformes à BS EN 10056 – 1: 1999
Gleichschenkliger winkelstahl gemäß BS EN 10056 – 1: 1999
Equal anglesaccording to BS EN 10056 – 1: 1999
Bezeichnungen Seite 2 Explanation page 2
r 2tr 1
h
t
r 2
b
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 14
Structural sections in accordance with European specifications
Corus Construction & Industrial 15Corus Construction & Industrial 15
Désignation
Bezeichnung
Section
L 90 x 90 x 6
L 90 x 90 x 8
L 90 x 90 x 10
L 90 x 90 x 12
L 100 x 100 x 8
L 100 x 100 x 10
L 100 x 100 x 12
L 100 x 100 x 15
L 120 x 120 x 8
L 120 x 120 x 10
L 120 x 120 x 12
L 120 x 120 x 15
L 150 x 150 x 10
L 150 x 150 x 12
L 150 x 150 x 15
L 150 x 150 x 18
L 200 x 200 x 16
L 200 x 200 x 18
L 200 x 200 x 20
L 200 x 200 x 24
iy
cm
2.76
2.74
2.72
2.70
3.06
3.04
3.02
2.98
3.69
3.67
3.65
3.62
4.62
4.60
4.57
4.54
6.16
6.13
6.11
6.06
ly
cm4
80.4
104
127
148
145
177
207
249
256
313
368
445
624
737
898
1050
2342
2600
2851
3331
lz
cm4
80.4
104
127
148
145
177
207
249
256
313
368
445
624
737
898
1050
2342
2600
2851
3331
lu
cm4
127
166
201
235
230
280
328
395
411
497
584
710
990
1170
1430
1680
3720
4150
4530
5280
lv
cm4
33.3
43.1
52.6
62.0
59.9
73.0
85.7
105
107
129
152
186
258
303
370
440
960
1050
1170
1380
lyz
cm4
-46.9
-61.5
-74.2
-86.5
-85.1
-104
-121
-145
-152
-184
-216
-262
-366
-434
-530
-620
-1380
-1550
-1680
-1950
iu
cm
3.47
3.45
3.42
3.40
3.85
3.83
3.80
3.76
4.67
4.63
4.60
4.57
5.82
5.80
5.76
5.73
7.76
7.75
7.70
7.64
iv
cm
1.78
1.76
1.75
1.75
1.96
1.95
1.94
1.94
2.38
2.36
2.35
2.34
2.97
2.95
2.93
2.92
3.94
3.90
3.92
3.90
Wy
cm3
12.2
16.1
19.8
23.4
20.0
24.6
29.1
35.6
29.1
36.0
42.7
52.4
56.9
67.8
83.5
98.8
162
181
199
235
Wz
cm3
12.2
16.1
19.8
23.4
20.0
24.6
29.1
35.6
29.1
36.0
42.7
52.4
56.9
67.8
83.5
98.8
162
181
199
235
iz
cm
2.76
2.74
2.72
2.70
3.06
3.04
3.02
2.98
3.69
3.67
3.65
3.62
4.62
4.60
4.57
4.54
6.16
6.13
6.11
6.06
Cornières à ailes égalesconformes à BS EN 10056 – 1: 1999
Gleichschenkliger winkelstahl gemäß BS EN 10056 – 1: 1999
Equal anglesaccording to BS EN 10056 – 1: 1999
Bezeichnungen Seite 2Notation page 2 Explanation page 2
vz
u
y
u
v
z s
y s
45º
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 15
Structural sections in accordance with European specifications
16 Corus Construction & Industrial16 Corus Construction & Industrial
Notation page 2
Désignation
Bezeichnung
Section
L 100 x 65 x 7
L 100 x 65 x 8
L 100 x 65 x 10
L 100 x 75 x 8
L 100 x 75 x 10
L 100 x 75 x 12
L 120 x 80 x 8
L 120 x 80 x 10
L 120 x 80 x 12
L 125 x 75 x 8
L 125 x 75 x 10
L 125 x 75 x 12
L 150 x 75 x 10
L 150 x 75 x 12
L 150 x 75 x 15
L 150 x 90 x 10
L 150 x 90 x 12
L 150 x 90 x 15
L 150 x 100 x 10
L 150 x 100 x 12
L 150 x 100 x 14
L 200 x 100 x 10
L 200 x 100 x 12
L 200 x 100 x 15
L 200 x 150 x 12
L 200 x 150 x 15
L 200 x 150 x 18
G
kg/m
8.77
9.94
12.3
10.6
13.0
15.4
12.2
15.0
17.8
12.2
15.0
17.8
17.0
20.2
24.8
18.2
21.6
26.6
19.0
22.5
26.1
23.0
27.3
33.7
32.0
39.6
47.1
h
mm
100
100
100
100
100
100
120
120
120
125
125
125
150
150
150
150
150
150
150
150
150
200
200
200
200
200
200
b
mm
65
65
65
75
75
75
80
80
80
75
75
75
75
75
75
90
90
90
100
100
100
100
100
100
150
150
150
t
mm
7
8
10
8
10
12
8
10
12
8
10
12
10
12
15
10
12
15
10
12
14
10
12
15
12
15
18
r1
mm
10
10
10
10
10
10
11
11
11
11
11
11
12
12
12
12
12
12
12
12
12
15
15
15
15
15
15
r2
mm
5.0
5.0
5.0
5.0
5.0
5.0
5.5
5.5
5.5
5.5
5.5
5.5
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
7.5
7.5
7.5
7.5
7.5
7.5
zs
cm
3.23
3.27
3.36
3.10
3.19
3.27
3.83
3.92
4.00
4.14
4.23
4.31
5.31
5.40
5.52
5.00
5.08
5.21
4.81
4.90
4.98
6.93
7.03
7.16
6.08
6.21
6.33
ys
cm
1.51
1.55
1.63
1.87
1.95
2.03
1.87
1.95
2.03
1.68
1.76
1.84
1.61
1.69
1.81
2.04
2.12
2.23
2.34
2.42
2.50
2.01
2.10
2.22
3.61
3.73
3.85
A
cm2
11.2
12.7
15.6
13.5
16.6
19.7
15.5
19.1
22.7
15.5
19.1
22.7
21.7
25.7
31.7
23.2
27.5
33.9
24.2
28.7
33.2
29.2
34.8
43.0
40.8
50.5
60.0
Cornières à ailes inégalesconformes à BS EN 10056 – 1: 1999
Ungleichschenkliger winkelstahl gemäß BS EN 10056 – 1: 1999
Unequal anglesaccording to BS EN 10056 – 1: 1999
Bezeichnungen Seite 2 Explanation page 2
t
t
r 2
h
b
r 2r 1
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 16
Structural sections in accordance with European specifications
Corus Construction & Industrial 17Corus Construction & Industrial 17
Désignation
Bezeichnung
Section
L 100 x 65 x 7
L 100 x 65 x 8
L 100 x 65 x 10
L 100 x 75 x 8
L 100 x 75 x 10
L 100 x 75 x 12
L 120 x 80 x 8
L 120 x 80 x 10
L 120 x 80 x 12
L 125 x 75 x 8
L 125 x 75 x 10
L 125 x 75 x 12
L 150 x 75 x 10
L 150 x 75 x 12
L 150 x 75 x 15
L 150 x 90 x 10
L 150 x 90 x 12
L 150 x 90 x 15
L 150 x 100 x 10
L 150 x 100 x 12
L 150 x 100 x 14
L 200 x 100 x 10
L 200 x 100 x 12
L 200 x 100 x 15
L 200 x 150 x 12
L 200 x 150 x 15
L 200 x 150 x 18
iy
cm
3.17
3.16
3.14
3.14
3.12
3.10
3.82
3.80
3.77
4.00
3.97
3.95
4.81
4.78
4.75
4.80
4.78
4.74
4.78
4.76
4.74
6.46
6.43
6.40
6.36
6.33
6.29
ly
cm4
113
127
154
133
162
189
226
276
323
247
302
354
501
589
713
533
627
761
553
651
745
1219
1441
1759
1653
2023
2376
lz
cm4
37.6
42.2
51.0
64.1
77.6
90.2
80.8
98.1
114
67.6
82.1
95.5
85.4
99.6
119
146
171
205
198
233
265
210
247
299
803
979
1146
lu
cm4
128
144
175
162
197
230
260
317
370
274
334
391
531
623
753
591
694
841
637
749
856
1290
1530
1860
2030
2480
2920
lv
cm4
22.0
24.8
30.1
34.6
42.2
49.5
46.6
56.8
66.7
40.9
49.9
58.5
55.1
64.7
78.6
88.3
104
126
114
134
154
135
159
193
430
526
623
lyz
cm4
-36.9
-41.6
-51.1
-53.5
-64.7
-75.6
-79.1
-94.8
-108
-74.6
-89.9
-105
-116
-134
-159
-161
-187
-225
-194
-226
-253
-278
-338
-398
-679
-826
-972
iu
cm
3.39
3.37
3.35
3.47
3.45
3.42
4.10
4.07
4.04
4.21
4.18
4.15
4.95
4.92
4.88
5.05
5.02
4.98
5.13
5.11
5.08
6.65
6.63
6.59
7.04
7.00
6.97
iv
cm
1.40
1.40
1.39
1.60
1.59
1.59
1.73
1.72
1.71
1.63
1.61
1.61
1.60
1.59
1.58
1.95
1.94
1.93
2.17
2.16
2.15
2.15
2.14
2.12
3.25
3.23
3.22
Wy
cm3
16.6
18.9
23.2
19.3
23.8
28.1
27.6
34.1
40.4
29.6
36.5
43.2
51.7
61.3
75.2
53.3
63.3
77.7
54.2
64.4
74.3
93.3
111
137
119
147
174
Wz
cm3
7.53
8.54
10.5
11.4
14.0
16.5
13.2
16.2
19.1
11.6
14.3
16.9
14.5
17.1
21.0
21.0
24.8
30.4
25.9
30.7
35.3
26.3
31.3
38.4
70.5
86.9
103
iz
cm
1.83
1.83
1.81
2.18
2.16
2.14
2.28
2.26
2.24
2.09
2.07
2.05
1.99
1.97
1.94
2.51
2.49
2.46
2.87
2.85
2.82
2.68
2.67
2.64
4.44
4.40
4.37
Cornières à ailes inégalesconformes à BS EN 10056 – 1: 1999
Ungleichschenkliger winkelstahl gemäß BS EN 10056 – 1: 1999
Unequal anglesaccording to BS EN 10056 – 1: 1999
Bezeichnungen Seite 2Notation page 2 Explanation page 2
vz
y s
u
y
u
v
z s
Non Standard Section Size. Please refer to account manager for availability of rollings.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 17
Structural sections in accordance with European specifications
18 Corus Construction & Industrial
Tolerances de laminage – BS EN 10034:1993Cette norme européenne précise les tolérances sur la
forme, les cotes et la masse des profilés en I
normalisés et des profilés pour poteaux en acier de
construction. Ces tolérances ne s’appliquent pas aux
profilés à semelle effilée.
Hauteur du profilé (h)
L’écart par rapport à la hauteur nominale du profilé,
mesurée sur la ligne médiane de l’epaisseur de l’âme,
doit être compris dans les tolérances données dans le
tableau 1 (a).
Tableau 1 (a). Tolérances sur la hauteur et la section
transversale.
Largeur de la semelle (b)
L’écart par rapport à la largeur nominale de la semelle
doit être compris dans les tolérances données dans le
tableau 1 (b).
Tableau 1 (b). Tolérances sur la largeur de la
semelle.
Epaisseur de l’âme (s)
L’écart par rapport à l’épaisseur nominale de l’âme,
mesurée au point médian de la dimension (h), doit être
compris dans les tolérances données dans le tableau 1
(c).
Tableau 1 (c). Tolérances sur l’épaisseur de l’âme.
Epaisseur de la semelle (t)
L’écart par rapport à l’épaisseur nominale de la semelle,
mesurée au point situé à un quart de la largeur de la
semelle, doit être compris dans les tolérances données
dans le tableau 1 (d).
Tableau 1 (d). Tolérances sur l’épaisseur de la
semelle.
18 Corus Construction & Industrial
Hauteur du profilé h
mm
Jusqu’a 180 compris
Plus de 180 et jusqu’à 400compris
Plus de 400 et jusqu’à 700compris
Plus de 700
Tolérance
mm
+ 3,0- 2,0
+ 4,0- 2,0
+ 5,0- 3,0
± 5,0
Largeur de la semelle b
mm
Jusqu’a 110 compris
Plus de 110 et jusqu’à 210compris
Plus de 210 et jusqu’à 325compris
Plus de 325
Tolérance
mm
+ 4,0- 1,0
+ 4,0- 2,0
± 4,0
+ 6,0- 6,0
Epaisseur de l’âme s
mm
Moins de 7
De 7 jusqu’à 10 non compris
De 10 jusqu’à 20 non compris
De 20 jusqu’à 40 non compris
De 40 jusqu’à 60 non compris
60 et plus
Tolérance
mm
± 0,7
± 1,0
± 1,5
± 2,0
± 2,5
± 3,0
Epaisseur de la semelle t
mm
Moins de 6,5
De 6,5 jusqu’à 10 non compris
De 10 jusqu’à 20 non compris
De 20 jusqu’à 30 non compris
De 30 jusqu’à 40 non compris
De 40 jusqu’à 60 non compris
60 et plus
Tolérance
mm
+1,5- 0,5
+ 2,0- 1,0
+ 2,5- 1,5
+ 2,5- 2,0
± 2,5
± 3,0
± 4,0
t*
h
b
xx
y
ys
b/4
13502 Corus Euro Inners 21/3/06 6:04 pm Page 18
Structural sections in accordance with European specifications
Corus Construction & Industrial 19Corus Construction & Industrial 19
Variation sur équerrage (k + k’)
La variation sur l’équerrage du profilé ne doit pas
excéder le maximum donné dans le tableau 2 (a).
Tableau 2 (a). Tolérances sur équerrage des profilés
en I et des profilés pour poteaux.
Décentrage de l’âme (e)
L’épaisseur au centre de l’âme ne doit pas s’écarter de
la position de la largeur médiane de la semelle de plus
de la distance (e) donnée dans le tableau 2(b).
Tableau 2 (b). Tolérances de décentrage de l’âme
des profiés en I et des profilés pour poteaux.
Variation sur rectitude (qxx ou qyy)
Le cambrage doit être conforme aux valeurs données
dans le tableau 3.
Tableau 3. Tolérances de cambrage des profilés en I
et des profilés pour poteaux.
Tolérance sur la masse
L’écart par rapport à la masse nominale d’un lot ou
d’une pièce individuelle ne doit pas excéder ± 4%.
L’écart de masse est la différence entre la masse réelle
du lot ou de la pièce et la masse calculée. La masse
calculée devra être déterminée en utilisant la densité de
7850 kg/m3.
Tolérance sur la longueur
Les profilés doivent être coupés aux longueurs
commandées dans les tolérances de, soit:
a) ± 50 mm
soit
b) -0 + 100 mm si des longueurs minimales sont
demandées.
L représente la longueur utilisable du profilé la plus
longue en supposant que les extrémités du profilé ont
été coupées d’équerre.
Largeur de la semelle b
mm
Jusqu’a 110 compris
Plus de 110
Hors d’équerre des semelles k + k’
mm
1,5
2% de b(maximum 6,5mm)
Hauteur de la section h
mm
Plus de 80 et jusqu’à 180compris
Plus de 180 et jusqu’à 360compris
Plus de 360
Tolérance qxx et qyy
sur longueur L
mm
0,30 L
0,15 L
0,1 L
b
h
k1
k
b
h
k1
k
qxx
qyy
b
b2b1
L
L max.
Largeur de la semelle b
mm
Jusqu’à 110mm inclus
Plus de 110 et jusqu’à 325compris
Plus de 325
Plus de 110 et jusqu’à 325compris
Plus de 325
Décentrage de l’âme où e = b1-b2
2mm
2,5
3,5
5,0
5,0
8,0
t < 40
t ≥ 40
13502 Corus Euro Inners 21/3/06 6:04 pm Page 19
Structural sections in accordance with European specifications
20 Corus Construction & Industrial20 Corus Construction & Industrial
Tolérances de laminage– BS EN 10056-2:1993Cette norme européenne précise les tolérances sur la
forme, les cotes et la masse des cornières à ailes égales
ou inégales en acier de construction laminé à chaud.
Tolérances sur les formes et les diménsions
longueur d’aile (a ou b)
L’écart par rapport à la longueur nominale de l’aile doit
être compris dans les tolérances données dans le
tableau 1(a). Dans le cas des cornières à ailes inégales,
la longueur de l’aile la plus longue (a) doit être utilisée
pour déterminer la plage des tolérances.
Tableau 1 (a). Tolérances dimensionnelles.
Epaisseur du profilé (t)
L’écart par rapport à l’épaisseur nominale doit être
compris dans les tolérances données dans le tableau
1(b).
Tableau 1 (b). Tolérances d’épaisseur.
Variation sur équerrage (k)
La variation sur équerrage du profilé
ne doit pas excéder le maximum
donné dans le tableau 1 (c). Dans le
cas des cornières à ailes inégales, la
longueur de l’aile la plus longue (a) doit être utilisée
pour déterminer la plage des tolérances.
Tableau 1 (c). Tolérances sur équerrage
Variation sur rectitude (q)
Le cambrage ne doit pas excéder les
tolérances données dans le tableau 1
(d). Dans le cas des cornières à ailes
inégales, la longueur de l’aile la plus longue (a) doit être
utilisée pour déterminer la plage des tolérances.
Tableau 1 (d). Tolérances sur cambrage
Tolérance sur la masse
L’écart par rapport à la masse nominale d’une pièce
individuelle ne doit pas excéder:
a) ± 6% de l’épaisseur pour t ≤ 4 mm, ou
b) ± 4% de l’épaisseur pour t > 4 mm.
L’écart par rapport à la masse nominale est la
différence entre la masse réelle de la pièce et la masse
calculée. La masse calculée doit être déterminée en
utilisant la densité de 7850 kg/m3.
Tolérance sur la longueur
La tolérance sur la longueur commandée doit être, soit:
a) ± 50 mm
soit
b) – 0 +100 mm si des longueurs minimales sont
demandées.
xx
y
y
t
t
a
b
q
L
Longueur de l’aile a
mm
Jusqu’à 50 compris
Plus de 50 et jusqu’à 100 compris
Plus de 100 et jusqu’à 150 compris
Plus de 150 et jusqu’à 200 compris
Plus de 200
Tolerancemm
± 1,0
± 2,0
± 3,0
± 4.0
+ 6,0-4,0
Epaisseur du profilé t
mm
Jusqu’à 5 compris
Plus de 5 et jusqu’à 10 compris
Plus de 10 et jusqu’à 15 compris
Plus de 15
Tolerancemm
± 0,50
± 0,75
± 1,00
± 1.20
DeviationkkDeviation
Hors d’équerre – longueur d’aile
mm
Jusqu’à 100 compris
Plus de 100 et jusqu’à 150 compris
Plus de 150 et jusqu’à 200 compris
Plus de 200
Tolérancemm
1,0
1,5
2,0
3.0
Longueur d’ailea
mm
Jusqu’à 150compris
Jusqu’à 200compris
Plus de 200
Sur longueurtotale
Ecartq
mm
0,4% L
0,2% L
0,2% L
Longueurconsidérée
mm
1,500
2,000
3,000
Ecartq
mm
6,0
3,0
3,0
Tolérance
Sur une partie
13502 Corus Euro Inners 21/3/06 6:04 pm Page 20
Structural sections in accordance with European specifications
Corus Construction & Industrial 21Corus Construction & Industrial 21
Walztoleranzen – BS EN10034:1993In diesem Europäischen Standard werden die
Toleranzwerte der Formabmessungen und Masse von
Baustahluniversalträgern und – säulen bestimmt. Diese
Angaben beziehen sich nicht auf Flansch- profile mit
Verjüngung.
Profilhöhe (h)
Die Abweichung vom Profilhöhennominalwert,
gemessen in der Mittellinie der Stegdicke, muß
innerhalb der Toleranzspanne laut Tabelle 1 (a) liegen.
Tabelle 1 (a) Toleranzwerte für Höhe und Querprofil
Flanschbreite (b)
Die Abweichung vom Flanschbreitennominalwert muß
innerhalb der Toleranzspanne laut Tabelle 1 (b) liegen.
Tabelle 1 (b) Toleranzwerte für Flanschbreite
Stegdicke
Die Abweichung vom Stegdickennominalwert,
gemessen am Mittelpunkt der Abmessung (h), muß
innerhalb der Toleranzspanne laut Tabelle 1 (c) liegen.
Tabelle 1 (c) Toleranzwerte für Stegdicke
Flanschdicke (t)
Die Abweichung vom Flanschdickennominalwert,
gemessen am Viertelpunkt der Flanschbreite, muß
innerhalb der Toleranzspanne laut Tabelle 1 (d) liegen.
Tabelle 1 (d) Toleranzwerte für Flanschdicke
Profilhöhe h
mm
Bis einschl. 180
Über 180 bis einschl. 400
Über 400 bis einschl. 700
Über 700
Toleranz
mm
+ 3.0-2.0
+ 4.0-2.0
+ 5.0-3.0
± 5.0
Flanschbreite b
mm
Bis einschl. 110
Über 110 bis einschl. 210
Über 210 bis einschl. 325
Über 325
Toleranz
mm
+ 4.0-1.0
+ 4.0-2.0
± 4.0
+ 6.0-5.0
Stegdicke s
mm
Unter 7
7 bis unter 10
10 bis unter 20
20 bis unter 40
40 bis unter 60
60 und mehr
Toleranz
mm
± 0.7
± 1.0
± 1.5
± 2.0
± 2.5
± 3.0
Flanschdicke t
mm
Unter 6.5
6.5 bis unter 10
10 bis unter 20
20 bis unter 30
30 bis unter 40
40 bis unter 60
60 und mehr
Toleranz
mm
+ 1.5- 0.5
+ 2.0- 1.0
+ 2.5- 1.5
+ 2.5- 2.0
± 2.5
± 3.0
± 4.0
t*
h
b
xx
y
ys
b/4
13502 Corus Euro Inners 21/3/06 6:04 pm Page 21
Structural sections in accordance with European specifications
22 Corus Construction & Industrial
Unrechtwinligkeit (k + k’)
Die Unrechtwinkligkeit des Profils darf den Maximalwert
laut Tabelle 2 (a) nicht überschreiten.
Tabelle 2 (a) Unrechtwinkligkeitstoleranzwerte für
Univeralträger und Säulen.
Steg außermittig
Die Dicke in der Mitte des Steges darf von der
Mittenposition auf der Breite des Flansches nicht mehr
als von dem in Tabelle 2 (b) angegebenen Abstand
abweichen.
Tabelle 2 (b) Toleranzwerte für Steg außermittig von
Geradheit (qxx oder qyy)
Die Geradheit muß mit den Anforderungen laut Tabelle 3
überschreiten.
Tabelle 3 Geradheitstoleranzwerte von
Universalträgern und Säulen.
Massentoleranzwert
Die Abweichung vom Massennominalwert eines Postens
oder Stückes darf + 4.0% nicht überschreiten.
Die Massenabweichung ist der Unterschied zwischen
der tatsächlichen Masse des Postens oder Stückes und
der berechneten Masse. Zur Festlegung der
berechneten Masse soll eine Dichte von 7850kg/m
angenommen werden.
Längentoleranzwert
Die Profile sollen auf die bestellten Längen geschnitten
werden, mit einer Toleranz von
a) ± 50 mm
oder
b) -0 + 100mm wenn Minimallängen verlangt
werden.
L bezeichnet die längste verwendbare Profillänge unter
der Annahme daß die Profilenden quadratisch
zugeschnitten wurden.
Flanschbreite b
mm
Bis einschl. 110
Über 110
Unrechtwinkligkeit derFlanschen k + k’
mm
1.5
2% von b(maximum 6.5mm)
Profilhöhe h
mm
Über 80 bis einschl. 180
Über 180 bis einschl. 360
Über 360
Toleranz qxx und qyy
auf Länge L
%
0.30 L
0.15 L
0.1 L
Flanschbreite b
mm
Bis einschl. 110
Über 110 bis einschl. 325
Über 325
Über 110 bis einschl. 325
Über 325
Steg außermittig bei e = b1-b2
2
mm
2.5
3.5
5.0
5.0
8.0
t < 40
t ≥ 40
b
h
k1
k
b
h
k1
k
qxx
qyy
b
b2b1
L
L max.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 22
Structural sections in accordance with European specifications
Corus Construction & Industrial 23
Walztoleranzen – BS EN10056-2:1993In diesem Europäischen Standard werden die
zulässigen Abweichungen in den Formabmessungen
und der Masse von warmgewalzten gleich- und
ungleichschenkligen Baustahlwinkelprofilen bestimmt.
Zulässige Abweichungen in Form und Abmessungen
Schenkellänge (a oder b)
Die Abweichung von Schenkellängennominalwert muß
innerhalb der Toleranzspanne laut Tabelle 1 (a) liegen.
Für ungleichschenklige Winkel muß die längere
Schenkellänge (a) zur Festlegung des Toleranzbereiches
genommen werden.
Tabelle 1 (a) Abmessungstoleranzwerte
Profildicke (t)
Die Abweichung vom Dickennominalwert muß innerhalb
der Toleranzspanne laut Tabelle 1 (b) liegen.
Tabelle 1 (b) Dickentoleranzwerte
Unrechtwinkligkeit (k)
Die Unrechtwinkligkeit des Profils darf
den Maximalwert laut Tabelle 1(c) nicht
überschreiten. Für ungleichschenklige
Winkel muß die längere Schenkellänge
(a) zur Festlegung des
Toleranzbereiches genommen werden.
Tabelle 1 (c) Rechtwinkligkeitstoleranzwerte
Geradheit (q)
Die Abweichung von der Geradheit darf die
Toleranzwerte laut Tabelle 1 (d) nicht überschreiten. Für
ungleichschenklige Winkel muß die
längere Schenkellänge (a) zur
Festlegung des Toleranzbereiches
genommen werden.
Tabelle 1 (d) Geradheitstoleranzwerte
Massentoleranzwerte
Die Abweichung vom Massennominalwert jedes
Einzelstückes darf folgende Werte nicht überschreiten:
a) 6% für Dicke für t < 4 mm/oder
b) 4% für Dicken für t > 4 mm.
Die Abweichung vom Massennominalwert ist der
Unterschied zwischen der tatsächlichen Masse des
Stückes und der berechneten Masse. Zur Festlegung
der berechneten Masse soll eine Dichte von 7850kg/m
angenommen werden.
Längentoleranzwerte
Der Toleranzwert für die bestellte Länge beträgt entweder
a) 50 mm
oder
b) +100-0
mm wenn Minimallängen benötigt werden.
xx
y
y
t
t
a
b
q
L
DeviationkkDeviation
Schenkellänge a
mm
Bis einschließlich 50
Über 50 bis einschließlich 100
Über 100 bis einschließlich 150
Über 150 bis einschließlich 200
Über 200
Toleranz
mm
± 1.0
± 2.0
± 3.0
± 4.0
+ 6.0- 4.0
Profildicke t
mm
Bis einschließlich 5
Über 5 bis einschließlich 10
Über 10 bis einschließlich 15
Über 15
Toleranz
mm
± 0.50
± 0.75
± 1.00
± 1.20
Unrechtwinkligkeit – Schenkellänge
mm
Bis einschließlich 100
Über 100 bis einschließlich 150
Über 150 bis einschließlich 200
Über 200
Toleranz
mm
1.0
1.5
2.0
3.0
Schenkellängea
mm
bes einschl.150
bes einschl. 200
Über 200
Über gesamteBarrenlänge
Abweichungq
mm
0.4% L
0.2% L
0.1% L
AngnommeneLänge
mm
1,500
2,000
3,000
Abweichung q
mm
6.0
3.0
3.0
Toleranz
Über Teillänge des Barrens
13502 Corus Euro Inners 21/3/06 6:04 pm Page 23
Structural sections in accordance with European specifications
24 Corus Construction & Industrial24 Corus Construction & Industrial
Rolling tolerances – BS EN 10034: 1993The European Standard specifies tolerances on shape
dimensions and mass of structural steel universal
beams and columns. These requirements do not apply
to taper flange sections.
Section height (h)
The deviation from nominal on section height measured
at the centre line of web thickness shall be within the
tolerance given in Table 1(a).
Table 1 (a) Tolerance on height and cross-section
Flange width (b)
The deviation from nominal on flange width shall be
within the tolerance given in Table 1(b).
Table 1 (b) Tolerance on flange width
Web thickness (s)
The deviation from nominal on web thickness measured
at the mid-point of dimension (h) shall be within the
tolerance given in Table 1(c)
Table 1 (c) Tolerances on web thickness
Flange thickness (t)
The deviation from nominal on flange thickness
measured at the quarter flange width point shall be
within the tolerance given in Table 1(d)
Table 1 (d) Tolerances on flange thickness
Section height h
mm
Up to and including 180
Greater than 180 up to and including 400
Greater than 400 up to and including 700
Greater than 700
Tolerance
mm
+3.0-2.0
+4.0-2.0
+5.0-3.0
± 5.0
Flange width b
mm
Up to and including 110
Greater than 110 up to and including 210
Greater than 210 up to and including 325
Greater than 325
Tolerance
mm
+4.0-1.0
+4.0-2.0
± 4.0
+6.0-5.0
Web thickness s
mm
Less than 7
7 up to but excluding 10
10 up to but excluding 20
20 up to but excluding 40
40 up to but excluding 60
60 and over
Tolerance
mm
± 0.7
± 1.0
± 1.5
± 2.0
± 2.5
± 3.0
Flange thickness t
mm
Less than 6.5
6.5 up to but excluding 10
10 up to but excluding 20
20 up to but excluding 30
30 up to but excluding 40
40 up to but excluding 60
60 and over
Tolerance
mm
+1.5-0.5
+2.0-1.0
+2.5-1.5
+2.5-2.0
± 2.5
± 3.0
± 4.0
t*
h
b
xx
y
ys
b/4
13502 Corus Euro Inners 21/3/06 6:04 pm Page 24
Structural sections in accordance with European specifications
Corus Construction & Industrial 25Corus Construction & Industrial 25
Out-of-squareness (k + k‘)
The out-of-squareness of the section shall not exceed
the maximum given in Table 2(a).
Table 2 (a) Tolerance on out-of-squareness of
universal beams and columns
Web off-centre (e)
The mid-thickness of the web shall not deviate from the
mid-width position on the flange by more than the
distance (e) given in Table 2(b).
Table 2 (b) Tolerance on web off-centre of universal
beams and columns
Straightness (qxx or qyy)
The straightness shall comply with the requirements
given in Table 3.
Table 3 Tolerance on straightness of universal
beams and columns
Tolerance on mass
The deviation from the nominal mass of a batch or a
piece shall not exceed ± 4.0%.
The mass deviation is the difference between the actual
mass of the batch or piece and the calculated mass.
The calculated mass shall be determined using a
density of 7850kg/m3.
Tolerance on length
The sections shall be cut to ordered lengths to
tolerances of:
a) ± 50mm
or
b) -0 + 100mm where minimum lengths are requested.
L represents the longest useable length of the section
assuming that the ends of the section have been cut
square.
Flange width b
mm
Up to and including 110
Greater than 110
Section height h
mm
Greater than 80 up to and including 180
Greater than 180 up toand including 360
Greater than 360
Out-of-squareness
of flanges k + k’
mm
1.5
2% of b
(maximum 6.5mm)
Tolerance qxx and qyy
on length L
%
0.30 L
0.15 L
0.1 L
Flange width b
mm
Up to and including 110
Greater than 110 up toand including 325
Greater than 325
Greater than 110 up toand including 325
Greater than 325
t < 40
t ≥ 40
Web off-centrewhere e = b1 – b2
2
mm
2.5
3.5
5.0
5.0
8.0
b
h
k1
k
b
h
k1
k
b
b2b1
qxx
qyy
L
L max.
13502 Corus Euro Inners 21/3/06 6:04 pm Page 25
Structural sections in accordance with European specifications
26 Corus Construction & Industrial26 Corus Construction & Industrial
Rolling tolerances – BS EN 10056-2:1993The European Standard specifies tolerances on shape
dimensions and mass of hot-rolled structural steel
equal and unequal leg angles.
Tolerances on shapes and dimensions
Leg length (a or b)
The deviation from nominal on leg length shall be within
the tolerance given in Table 1(a). For unequal leg angles
the longer leg length (a) shall be used to determine the
tolerance band.
Table 1 (a) Dimensional tolerances
Section thickness (t)
The deviation from nominal on thickness shall be within
the tolerances given in Table 1(b).
Table 1 (b) Thickness tolerances
Out-of-square (k)
Out-of-squareness of the section
shall not exceed the maximum
given in Table 1(c). For unequal leg
angles, the longer leg length (a)
shall be used to determine the
tolerance band.
Table 1 (c) Squareness tolerances
Straightness (q)
The deviation from straightness
shall not exceed the tolerances
given in Table 1(d). For unequal leg
angles, the longer leg length (a)
shall be used to determine the
tolerance band.
Table 1 (d) Straightness tolerances
Tolerance on mass
The deviation from the nominal mass of any individual
piece shall not exceed:
a) ± 6% for thickness for t ≤ 4mm or
b) ± 4% for thickness for t > 4mm.
The deviation from the nominal mass is the difference
between the actual mass of the piece and the
calculated mass. The calculated mass shall be
determined using a density of 7850kg/m3.
Tolerance on length
The tolerance on ordered length shall be either:
a) ± 50mm; or
b) -0 +100mm where minimum lengths are required.
Leg length a
mm
Up to and including 50
Greater than 50 up toand including 100
Greater than 100 up toand including 150
Greater than 150 up toand including 200
Greater than 200
Tolerancemm
± 1.0
± 2.0
± 3.0
± 4.0
+ 6.0- 4.0
Section thickness t
mm
Up to and including 5
Greater than 5 up toand including 10
Greater than 10 up toand including 15
Greater than 15
Tolerance
mm
± 0.50
± 0.75
± 1.0
± 1.20
Out of square – leg length
mm
Up to and including 100
Greater than 100 up toand including 150
Greater than 150 up toand including 200
Greater than 200
Tolerancemm
1.0
1.5
2.0
3.0
Leg lengtha
mm
Up to andincluding 150
Up to andincluding 200
Greater than 200
Overfull bar length
Deviationq
mm
0.4% L
0.2% L
0.1% L
Lengthconsidered
mm
1,500
2,000
3,000
Deviationq
mm
6.0
3.0
3.0
Tolerance
Over any part bar length
xx
y
y
t
t
a
b
DeviationkkDeviation
q
L
13502 Corus Euro Inners 21/3/06 6:04 pm Page 26
Structural sections in accordance with European specifications
Corus Construction & Industrial 27Corus Construction & Industrial 27
Offices and agents for Corus Exports
EuropeBelgiumCorus International Benelux(as Netherlands)
CyprusGevo Limited9 Meletiou MetaxakiPO BOX 21307NicosiaCyprusTel: (00) 35 7 22343045Fax: (00) 35 7 22343065
Czech RepublicCorus International1st FloorMala Stepanska 9120 00 Praha 2Czech RepublicTel: (00) 42 02249 20477Fax: (00) 42 02249 19546
DenmarkCorus International Denmark ASKongevejen 71PO BOX113DK2840 HolteDenmarkTel: (00) 45 399 60900Fax : (00) 45 399 60949
FinlandCorus International FinlandHitsaajankatu 22FI-00810 HelsinkiFinlandTel: (00) 35 894 542450Fax: (00) 35 894 5424520
FranceCorus International France3 Allee des BarbanniersF-92632 Gennevillers CedexFranceTel: (00) 33 (0) 1 4147 3315Fax: (00) 33 (0) 1 4085 1149
GermanyCorus International Deutschland GMBHAm Trippelsberg 4840589 DusseldorfGermanyTel: (00) 49 211 4926 0Fax: (00) 49 211 4926 282
GreeceNicholas Skender Agencies Ltd2 A.Papandreou StreetMelissia 151 27GreeceTel: (00) 30 210 8035445Fax: (00) 30 210 8035450
IrelandCorus International IrelandLeeson Court88 Lower Leeson StreetDublin 2Republic of IrelandTel: (00) 353 (0) 1 661 6773Fax: (00) 353 (0) 1 676 5413Fax: (00) 353 (0) 1 676 5406
ItalyCorus International ItaliaPietro Rondoni 120146 MilanoItalyTel: (00) 39 024 22554245Tel: (00) 39 024 22554271Fax: (00) 39 024 22554250
Malta BaldachinoDar NinuDawret Hal Ghaxaq, GhaxaqZTN 11MaltaTel: (00) 35 6878 616Fax: (00) 35 6673 479
NetherlandsCorus International BeneluxFregatweg 44A6222 NZ MaastrichtNetherlandsTel: (00) 31 43 36 88444Fax: (00) 31 43 36 88484
NorwayCorus International NorwayHarbitzalleen 2APO Box 13, Skoyen0212 OsloNorwayTel: (00) 47 9002 9303Fax: (00) 47 2252 3411
PolandCorus International Polandul. Piastowska 740-005 KatowicePolandTel: (00) 48 32 608 3510Fax: (00) 48 32 608 3502
PortugalCorus International PortugalCorus Metal Iberica S.A. – Sucursal dePortugalAv. Miguel Bombarda 36 8th Floor Letter I1050-165 LisboaPortugalTel: (00) 35 121 781 7040Fax: (00) 35 121 781 7049
SpainCorus International SpainRosario Pino 14-16Torre Rioja28020 MadridSpainTel: (00) 34 914 252 910Fax: (00) 34 915 721 295/375
SwedenCorus International SwedenBarlastgatan 2SE-416 63 GothenburgSwedenTel: (00) 46 31 779 3200Fax: (00) 46 31 779 3228
SwitzerlandCorus Schwiz AGWartenbergstrasse 45CH- 4020 BaselSwitzerlandTel: (00) 41 (0) 61378 9828Fax: (00) 41 (0) 61378 9829
North AmericaUSACorus International Americas475 North Martingale Road, Suite 400Schaumburg, Illinois 60173 USATel: (00) 1 847 619 0400Fax: (00) 1 847 619 0468
USACorus International America Houston13135 Dairy Ashford Road, Suite 570Sugar Land, Texas 77478 USATel: (00) 1 281 313 8666Fax: (00) 1 281 313 8668
MexicoCorus International AmericasTorre GIA Morones Prieto 2805Floor 5, Suite 1 & 2Monterrey, NL 64710 MexicoTel: (00) 52 81 8319 0228Fax: (00) 52 81 8319 0227
ChinaBeijingCorus Asia LimitedBeijing Representative OfficeUnit 1313, China World Tower 1,No.1 Jianguomenwai Avenue,Beijing 100004, China.Tel: (00) 86 10 6505 6194-8Fax: (00) 86 10 6505 6199
Guangzhou Corus Asia LimitedGuangzhou Representative OfficeRoom 1207, Yi An Plaza,33 Jian She Liu Ma Road Guangzhou 510060, ChinaTel: (00) 86 20 8363 4242Fax: (00) 86 20 8363 4747
Hong KongCorus Asia LimitedUnit 2106-10, Devon House,979 King's Road, Quarry Bay,Hong KongTel: (00) 852 2807 0196Fax: (00) 852 2807 1805
ShanghaiCorus Asia LimitedShanghai Representative OfficeRoom 2506, K. Wah Centre1010 Huai Hai Road MiddleXuhui DistrictShanghai 200031, ChinaTel: (00) 86 21 5405 1616Fax: (00) 86 21 5404 5118
13502 Corus Euro Inners 21/3/06 6:04 pm Page 27
Structural sections in accordance with European specifications
28 Corus Construction & Industrial28 Corus Construction & Industrial
Far EastIndonesiaCorus Asia LimitedIndonesia Representative OfficeWorld Trade Centre, 11th Floor,29/31 Jalan Jendral SudirmanJakarta 12920, IndonesiaTel: (00) 62 21 521 1365Fax: (00) 62 21 521 1334
JapanCorus Asia LimitedJapan Representative Office506, Ichibancho Central Building,22-1, Ichibancho, Chiyoda-ku,Tokyo 102-0082, JapanTel: (00) 81 3 5215 0445-6Fax: (00) 81 3 5215 0447
Korea Corus Asia LimitedKorea BranchRoom 802, Hanaro Building,194-4, Insa-Dong,Chongro-Ku, Seoul 110, KoreaTel: (00) 82 2 733 6741-3Fax: (00) 82 2 733 6745
MalaysiaCorus Metals (M) Sdn BhdUnit 527, 5th Floor, Block A,Damansara Intan, No.1 Jalan SS20/27,47400 Petaling JayaSelangor Darul Ehsan, MalaysiaTel: (00) 603 7726 9226Fax: (00) 603 7726 9227
PhilippinesCorus Asia LimitedPhilippines Representative OfficeUnit 601B, 6/F King Center Building,#57 Sgt. Rivera Street,Quezon City, PhilippinesTel: (00) 632 363 6593 Fax: (00) 632 363 6530
SingaporeCorus South East Asia Pte Ltd24 Raffles Place#29-05 Clifford CentreSingapore 048621, SingaporeTel: (00) 65 6297 6678Fax: (00) 65 6297 6682
TaiwanCorus Asia LimitedTaiwan Branch14/Fl., 50 Hsing Sheng South Road,Section 1, Taipei,Taiwan, Republic of ChinaTel: (00) 886 2 2395 4638Fax: (00) 886 2 2321 8088
ThailandCorus Metals (Thailand) Limited31st Floor, Ocean Tower II Building75/77 Soi Sukhumvit 19, Sukhumvit RoadKwaeng Klong Toey-Nua, Khet WattanaBangkok 10110, ThailandTel: (00) 66 2 661 6639-41 Fax: (00) 66 2 661 6638
Vietnam Corus International Trading LimitedVietnam Representative Office8 Floor, Jardine House,58 Dong Khoi Street, District 1,Ho Chi Minh City, VietnamTel: (00) 84 8 822 2340Fax: (00) 84 8 823 0030
IndiaChennai (Madras)Corus InternationalNo 4 Ceebros Centre45 Montieth RoadEgmore, Chennai 600 008IndiaTel: (00) 91 44 829 0209Fax: (00) 91 44 829 1256
Mumbai (Bombay)Corus International412 Raheja Chambers213 Backbay ReclamationMumbai 400 021IndiaTel: (00) 91 22 282 3126Fax: (00) 91 22 287 5148
New DelhiCorus InternationalD-1, Shopping Centre 2, Postbag 1Vasant ViharNew Delhi 110 057IndiaTel: (00) 91 11 2614 4373Fax: (00) 91 11 2614 2147
Other CountriesAustraliaCorus International AustraliaFactory 480/82 Hallam South RoadHallam, Victoria 03803AustraliaTel: (00) 61 3 8795 7833Fax: (00) 61 3 8795 7844
BrazilCorus International AmericasRua Farani, 26 – s. 24622231-020 – Rio de Janeiro – RJBrazilTel: (00) 55 (21) 2246 8228Fax: (00) 55 (21) 2246 1740
ColombiaGeorge RaikesRaikes Y CIA. S en C. ColombiaCalle 69 No. 4-68 Officina 302Bogota, D.C. – ColombiaTel: (00) 57 541 5708 – 248 1523Fax: (00) 57 1210 3685
ChileRepco LTDA. (Corus)9 Norte 555 OF 301Casilla 9030-3Vina del Mar, ChileTel: (00) 56 32 686667Fax: (00) 56 32 978475
EgyptCorus International144 Al-Orouba StreetHeliopolisCairo, EgyptTel: (00) 202 418 5655Fax: (00) 202 418 6116
GhanaCorus International ProjectsPO Box KA 30372Aviation House Suite 302Airport Residential AreaAccra, GhanaTel: (00) 233 21 767 226 Fax: (00) 233 21 767 229
IranCorus ConsultancyNo 57 10th Floor Ferdows Building1777 Vali-Asr AveTehran 19617IranTel: (00) 98 (0) 21 270 7211Fax: (00) 98 (0) 21 270 7213
IsraelDizengoff Trading Co. 1952 Ltd.Offer House8 Hamanofim StreetHerzlia 46120P.O. Box 2114, IsraelTel: (00) 97 299 505 110Fax: (00) 97 299 507 002
KazakhstanCorus International ProjectsAzattyk Street 48Office 602BAtyrau, Kazakhstan 06005Tel: (00) 7 3122 970 105Fax: (00) 7 3122 970 106
LibyaCorus International Projects52 Al-Fatah TowerTripoli, Libya
New ZealandCorus International New Zealand7 Bruce Roderick DriveEast Tamaki 1701, PO Box 58-880Greenmount 1730Auckland, New ZealandTel: (00) 64 (0) 927 11780Fax: (00) 64 (0) 927 11970
RussiaCorus International Trading5/2 Office N 320Naryhkinskya AlleyMoscow, RussiaTel: (00) 7 0951 395 633
Saudi ArabiaCorus Middle Eastc/o Yusuf bin Ahmed KanooPO Box 37Dammam 31411Kingdom of Saudi ArabiaTel: (00) 966 (0) 3859 0930Fax: (00) 966 (0) 3857 9750
South AfricaCorus International South AfricaPO Box 15113Farrarmere, 1518 BenoniJohannesburgSouth AfricaTel: (00) 27 (011) 849 8500Fax: (00) 27 (011) 849 8501
TurkeyCorus Celik Ticaret ASAsik Kerem Sokak No 30 kat 3DikilitasBesiktas 34349Istanbul, TurkeyTel: (00) 90 212 258 4684Fax: (00) 90 212 227 1764
UAECorus Middle EastPO Box 18294Jebel Ali, DubaiUnited Arab EmiratesTel: (00) 971 (0) 4887 3232Fax: (00) 971 (0) 4887 3966
13502 Corus Euro Inners 21/3/06 6:04 pm Page 28
www.corusgroup.com
Corus Construction & IndustrialTechnical Sales and MarketingPO Box 1 Brigg RoadScunthorpeNorth LincolnshireDN16 1BP
T: +44 (0) 1724 405060F: +44 (0) 1724 404224
email: [email protected]/structuralsteelwebsite: www.corusconstruction.com
English, French and German language version CC&I:RS:3000:UK:02/2006
Care has been taken to ensure that thisinformation is accurate, but Corus Group plc,including its subsidiaries, does not acceptresponsibility or liability for errors orinformation which is found to be misleading.
Copyright 2006Corus
13502 Corus Euro Cover.qxd 22/3/06 10:37 am Page 1