7/27/2019 Euro Therma TR27 2pp
2/2
DescriptionKingspan Therma TR27 FM comprises a high
performance
rigid thermoset polyisocyanurate (PIR) insulation core, faced
onboth sides with a coated glass tissue based facing,
autohesively bonded to the insulation core during
manufacture.
GeneralResistance to Solvents, Fungi & Rodents
The insulation core is resistant to shortterm contact with
petrol and with most dilute acids, alkalis and mineral oils.
However, it is recommended that any spills be cleaned off
fully
before the boards are installed. Ensure that safe methods of
cleaning are used, as recommended by suppliers of the spilt
liquid. The insulation core is not resistant to some solvent
based adhesive systems, particularly those containing methyl
ethyl ketone. Adhesives containing such solvents should not
be used in association with this product. Damaged boards or
boards that have been in contact with harsh solvents or
acids
should not be used.
Cutting
Cutting should be carried out by using a fine toothed saw.
Ensure accurate trimming to achieve closebutting joints and
continuity of insulation.
Daily Working Practice
At the completion of each days work, or whenever work
is interrupted for extended periods of time, a night joint
must be made in order to prevent water penetration into theroof
construction.
Packaging and Storage
The polyethylene packaging of Kingspan Insulation products,
which is recyclable, should not be considered adequate for
outdoor protection. Ideally, boards should be stored inside
a
building. If, however, outside storage cannot be avoided,
then
the boards should be stacked clear of the ground and covered
with an opaque polythene sheet or weatherproof tarpaulin.
Boards that have been allowed to get wet should not be used.
Health and Safety
Kingspan Insulation products are chemically inert and safe
touse. A Safety Information Data Sheet for this product is
available from the Kingspan Insulation website.
Warning do not stand on or otherwise support your weight on this
product unless it is fully
supported by a load bearing surface.
FM & LPCB Certification
The product is certified as achieving Class 1 Insulated
Steel
Deck Pass to FM research standards 4450: 1989 and 4470:
2010, subject to the conditions of approval as a roof
construction for use in Class 1 roof constructions as
described
in the current edition of the FM Research Approval Guide.
Metal deck roofing constructions, incorporating a sealed
metal
deck or a separate vapour control layer and 30-120 mm of the
product in a single layer, have been successfully tested to
LPS 1181: Part 1, achieving an EXT B rating. For further
details, please search for approval reference number 388b/02
on www.redbooklive.com .
Product Data
Property Result
General
Product Thickness Refer to local distributor for currentstock
and nonstock sizes
Board Length (mm) 2400 1200
Board Width (mm) 1200 600
Compressive Strength Typically exceeds 150 kPa(EN 826) @ 10%
compression
Dimensional Stability - 48 Hours 2% (70C & 90% RH (EN 1604)
length & breadth)
6% (70C & 90% RH thickness)
Diffusion Resistance Factor 60
Thermal
Thermal Conductivity 0,027 W/m.K (thickness < 80)(EN 13165)
0,026 W/m.K (thickness 80 119 mm)
0,025 W/m.K (thickness 120 mm)
Fire
Reaction to Fire E ( tested as placed on market)(EN 13501)
Bs3d0* (tested in application)
External Flame Spread BROOF (t2)**(ENV 1187)
Resistance to Fire 32 minutes integrity***(EN 1363-1),(EN
1363-2),(EN 1365-2)
*Has achieved this result when tested in accordance with EN
13165/A2: 2005 and EN 15715:2007 as part of a construction
consisting of the Kingspan Therma
TM
TR27 FM screwed to a34/1035 steel deck and backed by a calcium
silicate board. In the steel deck a vertical joint at
200 mm was applied. The steel deck side was exposed to the
fire.**Has achieved this result when tested as part of a
construction consisting of a 1.2 mm
polyester reinforced PVC-foil membrane applied to 50 mm
ofKingspan ThermaTM
TR27 FM. Please note that actual performance is dependant the
single-ply membrane adoptedand should be verified with the Kingspan
Insulation Technical Service Department.***Has achieved this result
when tested as part of a composite steel roof construction
consistingof: 0.75 mm trapezoidal steel sheets fixed together with
4.8 mm x 16 mm self-drilling screws
at 250 mm centres; a 0.2 mm thick polyethylene vapour barrier
foil; two layers of 55 mmKingspan Therma
TM
TR27 FM; and a 1.2 mm thick PVC waterproofing membrane.
Standards & ApprovalsKingspan Therma TR27 FM is manufactured
tothe highest standards under a management system certified to
BS EN ISO 9001: 2008 (Quality Management Systems.
Requirements),BS EN ISO 14001: 2004 (Environmental Management
Systems.
Requirements) and BS OHSAS 18001: 2007 (Health &
SafetyManagement Systems. Requirements).
Kingspan Insulation B.V.Lorentzstraat 1, 7102 JH, Winterswijk,
Netherlands
Tel: +31 (0) 543 543 210 Fax: +31 (0) 344 675 215
email: [email protected]
Technical Advic e
Tel: 00800 Kingspan (00800 54647726)
Fax: +31 (0) 344 675 215email:
[email protected]
www.kingspaninsulation.eu
Kingspan and the Lion Device are Registered Trademarks of the
Kingspan Group plc in the EU
and other countries. All rights reserved.
Therma is a Trademark of the Kingspan Group plc.
Registered in Netherlands No. 11 053 542. Registered Office:
Kingspan Insulation B.V., Winterswijk, NL.
VAT NL 81 09 09 881 B01
TR27 FMKingspan
