ETSI EN300 328 RADIO TEST REPORT...2018/12/18 · Pressure range 86-106kPa 86-106kPa Power supply DC 3.7V DC 3.15V and DC 4.26V Note 1: The HT 55°C and LT -20°C was declarated by

Report No.: 18EEAB10012 21 1 of 48

DongGuan ShuoXin Electronic Technology Co., Ltd. Zone A, 1F, No. 6, XinGang Road YuanGang Street, XinAn District, ChangAn Town, DongGuan City, GuangDong, China Phone: 86-769-3902 6866; Fax: 86-769-8509 8777 E-mail: [email protected] Rev. 2.0

ETSI EN300 328 RADIO TEST REPORT

Report Reference No. ...................... : 18EEAB10012 21

Date Sample(s) Received ................ : 2018-10-30

Date Tested ..................................... : From 2018-10-30 to 2018-11-15

Date of issue .................................... : 2018-11-20

Testing Laboratory ........................... : DongGuan ShuoXin Electronic Technology Co., Ltd.

Address ............................................ : Zone A, 1F, No. 6, XinGang Road YuanGang Street, XinAn

District, ChangAn Town, DongGuan City, GuangDong, China

Applicant’s name .............................. : EMC Healthcare Co., Ltd.

Address ............................................. WTC Building 33F, 2-4-1 Hamamatsucho, Minato-ku, Tokyo,

JManufacturer .................................... : Dalian JY Electronic Technology Co., Ltd.

Test specification:

Test item description ........................ : CALM. Module

Trade Mark ....................................... : N/A

Model/Type reference .................... : SVN-840C

Ratings ............................................. : I/P: DC 5V

O/P: --

Responsible Engineer :

Smile Wang

Approved by:

King Wang



TABLE OF CONTENTS

TEST REPORT DECLARE ................................................................................................................... 4

1.Summary of test results ..................................................................................................................... 5

1.1.Standard description ....................................................................................................................... 5

1.2.Test result ....................................................................................................................................... 5

2.General test information..................................................................................................................... 6

2.1.Description of Device (EUT) ........................................................................................................... 6

2.2.Receiver categories ........................................................................................................................ 6

2.3.Block diagram of EUT configuration for test ................................................................................... 7

2.4.Test channel conditions .................................................................................................................. 7

2.5.Test environment conditions ........................................................................................................... 8

2.6.Measurement uncertainty ............................................................................................................... 9

3.RF output power ..............................................................................................................................10

3.1.Test equipment .............................................................................................................................10

3.2.Block diagram of test setup ..........................................................................................................10

3.3.Limits .............................................................................................................................................10

3.4.Test Procedure .............................................................................................................................11

3.5.Test Result ....................................................................................................................................12

4.Power Spectral Density....................................................................................................................13

4.1.Test equipment .............................................................................................................................13


4.3.Limit ...............................................................................................................................................13

4.4.Test Procedure .............................................................................................................................14

4.5.Test result .....................................................................................................................................15

5.Occupied Channel Bandwidth .........................................................................................................18

5.1.Test equipment .............................................................................................................................18


5.3.Limits .............................................................................................................................................18

5.4.Test Procedure .............................................................................................................................18

5.5.Test Result ....................................................................................................................................19

6.Transmitter unwanted emissions in the out-of-band domain ...........................................................21

6.1.Test equipment .............................................................................................................................21


6.3.Limits .............................................................................................................................................21

6.4.Test Procedure .............................................................................................................................23

6.5.Test Result ....................................................................................................................................25

7.Receiver Blocking ............................................................................................................................27

7.1.Test equipment .............................................................................................................................27



7.2.Test setup .....................................................................................................................................27

7.3.Limits .............................................................................................................................................28

7.4.Test procedure ..............................................................................................................................28

7.5.Test Result ....................................................................................................................................29

8.Transmitter unwanted emissions in the spurious domain ...............................................................30

8.1.Test equipment .............................................................................................................................30


8.3.Limits .............................................................................................................................................31

8.4.Test Procedure .............................................................................................................................31

8.5.Tesr Result ....................................................................................................................................32

9.Receiver spurious emissions ...........................................................................................................40

9.1.Test equipment .............................................................................................................................40


9.3.Limits .............................................................................................................................................41

9.4.Test Procedure .............................................................................................................................41

9.5.Test Result ....................................................................................................................................42

10.Test setup photograph ...................................................................................................................46

11.EUT photograph .............................................................................................................................47

Report No.: 18EEAS10002 21 4 of 48


TEST REPORT DECLARE

Test Standard Used:

ETSI EN 300 328 V2.1.1 (2016-11)

We Declare: The equipment described above is tested by DongGuan ShuoXin Electronic Technology Co., Ltd. and in the

configuration tested the equipment complied with the standards specified above. The test results are

contained in this test report and DongGuan ShuoXin Electronic Technology Co., Ltd. is assumed of full

responsibility for the accuracy and completeness of these tests.

After test and evaluation, our opinion is that the equipment In Accordance with ETSI EN300 328 V2.1.1

about the effective uses allocated spectrum requirements of Article 3.2 of the RED Directive.

Report No: 18EEAS10002 21

Date of Test: 2018-10-30---2018-11-15 Date of Report: 2018-11-20

Note: This report applies to above tested sample only. This report shall not be reproduced in parts without

written approval of DongGuan ShuoXin Electronic Technology Co., Ltd.

Applicant : EMC Healthcare Co., Ltd.

Address : WTC Building 33F, 2-4-1 Hamamatsucho, Minato-ku, Tokyo, Japan

Equipment under Test : CALM. Module

Model No : SVN-840C

Trade Mark N/A

Manufacturer : Dalian JY Electronic Technology Co., Ltd.

Address : Floor 1-4, No. 13-1, Youquan Road, Zhanqian Street, Jinzhou District, Dalian, Liaoning, China



1. Summary of test results

1.1. Standard description

ETSI EN300 328 V2.1.1:Electromagnetic Compatibility and Radio Spectrum Matters; Wideband transmission

systems; Data transmission equipment operation in the 2.4GHz ISM band and using wide band modulation

techniques; Harmonized EN covering essential requirements under article 3.2 of the RED Directive.

1.2. Test result Description of Test Item Standard Results

RF Output Power ETSI EN 300 328 V2.1.1 clause

4.3.2.2 PASS

Power Spectral Density ETSI EN 300 328 V2.1.1 clause

4.3.2.3 PASS

Duty cycle, Tx-Sequence, Tx-gap ETSI EN 300 328 V2.1.1 clause

4.3.2.4 Not Applicable (See Note 1/2)

Medium Utilization (MU) factor ETSI EN 300 328 V2.1.1 clause

4.3.2.5 Not Applicable (See Note 1/2)

Occupied Channel Bandwidth ETSI EN 300 328 V2.1.1 clause

4.3.2.7 PASS

Transmitter unwanted emissions in the out-of-band domain

ETSI EN 300 328 V2.1.1 clause 4.3.2.8

PASS

Transmitter unwanted emissions in the spurious domain

ETSI EN 300 328 V2.1.1 clause 4.3.2.9

PASS

Receiver spurious emissions ETSI EN 300 328 V2.1.1 clause

4.3.2.10 PASS

Adaptivity ETSI EN 300 328 V2.1.1 clause

4.3.2.6

Not Applicable (See Note 1/2)

Receiver blocking ETSI EN 300 328 V2.1.1 clause

4.3.2.11

Not Applicable (See Note 1/2)

Note:

1. These requirements do not apply for equipment with a maximum declared RF output power of less than 10 dBm EIRP or for equipment when operating in a mode where the RF output power is less than 10 dBm EIRP.

2. These requirements apply to non-adaptive frequency hopping equipment or to adaptive frequency hopping equipment operating in a non-adaptive mode



2. General test information

2.1. Description of Device (EUT) EUT : CALM. Module

Trade Mark : N/A

Model Number : SVN-840C

Serial Model : N/A

Model Difference : N/A

Operation frequency : 2402-2480MHz

Modulation : GFSK

Adaptive/non-adaptive : Adaptive equipment

Antenna Designation : Ceramic Antenna

Antenna Gain(Peak) : Maximum PK gain: 3.5dBi

Adapter : N/A

Battery : DC 3V

Bluetooth Version : BT V5.0 BLE

Hardware Version : V1.0

Software Version : V6.1.0

2.2. Receiver categories

EUT belong Receiver

categories Categorization

1 Adaptive equipment with a maximum RF output power greater than 10 dBm e.i.r.p.

2 Non-adaptive equipment with a Medium Utilization (MU) factor greater than 1 % and less than or equal to 10 % or adaptive equipment with a maximum RF output power of 10 dBm e.i.r.p.

3 Non-adaptive equipment with a maximum Medium Utilization (MU) factor of 1 % or adaptive equipment with a maximum RF output power of 0 dBm e.i.r.p.



2.3. Block diagram of EUT configuration for test

The EUT has been tested as an independent unit together with other necessary accessories or support units.

The following support units or accessories were used to form a representative test configuration during the

tests..

Item Equipment Brand Model/Type No. Series No. Note

E-1 Notebook ACER MS2367 3280781076

6 /

Item Shielded Type Ferrite Core Length Note

Note:

(1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column.

2.4. Test channel conditions

Channel List CH Frequency CH Frequency CH Frequency CH Frequency 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480

EUT

Control PC

AC mains Test jig



Tested mode, channel, and data rate information Mode data rate (Mpbs)

(see Note) Channel Frequency

(MHz)

BLE GFSK 1 Low :CH0 2402 1 Middle: CH19 2440 1 High: CH39 2480

Note: According exploratory test, EUT will have maximum output power in those data rate, so those data rate were used for all test.

2.5. Test environment conditions During the measurement the environmental conditions were within the listed ranges:

Normal Conditions Extreme Conditions

Temperature range 21-25℃ -20℃ and 55℃

Humidity range 40-75% 40-75%

Pressure range 86-106kPa 86-106kPa

Power supply DC 3.7V DC 3.15V and DC 4.26V

Note 1: The HT 55°C and LT -20°C was declarated by manufacturer, The EUT couldn’t be operate normally with higher or lower temperature.

Note 2: The High Voltage 4.26V and Low Voltage 3.15V was declarated by manufacturer, The EUT couldn’t be operate normally with higher or lower voltage.



2.6. Measurement uncertainty

Test Item Uncertainty

Uncertainty for Conduction emission test (9kHz-150kHz) 3.7 dB

Uncertainty for Conduction emission test (150kHz-30MHz) 3.3 dB

Uncertainty for Radiation Emission test (30MHz-200MHz) 4.60 dB (Polarize: V)

4.60 dB (Polarize: H)

Uncertainty for Radiation Emission test (200MHz-1GHz) 6.10 dB (Polarize: V)


Uncertainty for Radiation Emission test (1GHz-6GHz) 5.01 dB (Polarize: V)






Uncertainty for radio frequency ±0.048kHz

Uncertainty for conducted RF Power ±0.32dB

Note：This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.



3. RF output power

3.1. Test equipment

Item Equipment Manufacturer Model No. Serial No. Calibrated

until Cal. Interval

1 Power Sensor KEYSIGHT U2021XA MY55240009 05/25/2019 1 Y




5 Const

Temp.&Humidity Chamber

Giant Force ITH-225-20-S IAB0309-001 06/05/2019 1 Y

3.2. Block diagram of test setup

3.3. Limits The maximum RF output power for adaptive Frequency Hopping equipment shall be equal to or less than 20 dBm. The maximum RF output power for non-adaptive Frequency Hopping equipment shall be declared by the supplier. See clause 5.3.1 m). The maximum RF output power for this equipment shall be equal to or less than the value declared by the supplier. This declared value shall be equal to or less than 20 dBm. This limit shall apply for any combination of power level and intended antenna assembly.

Temperature and Humidity Chamber

EUT

MIMO Power Measurement

Test Set PC(Test software)

DC Power Supply



3.4. Test Procedure Step 1:

(1) Use a fast power sensor suitable for 2,4 GHz and capable of minimum 1 MS/s.

(2) Use the following settings:

- Sample speed 1 MS/s or faster.

- The samples shall represent the RMS power of the signal.

- Measurement duration: For non-adaptive equipment: equal to the observation period defined in

clause 4.3.1.3.2 or clause 4.3.2.4.2. For adaptive equipment, the measurement duration shall be

long

enough to ensure a minimum number of bursts (at least 10) are captured.

NOTE 1: For adaptive equipment, to increase the measurement accuracy, a higher number of bursts may

be used.

Step 2 :

(1) For conducted measurements on devices with one transmit chain:

- Connect the power sensor to the transmit port, sample the transmit signal and store the raw data.

Use these stored samples in all following steps.

(2) For conducted measurements on devices with multiple transmit chains:

- Connect one power sensor to each transmit port for a synchronous measurement on all transmit

ports.

- Trigger the power sensors so that they start sampling at the same time. Make sure the time

difference between the samples of all sensors is less than 500 ns.

- For each individual sampling point (time domain), sum the coincident power samples of all ports

and

store them. Use these summed samples in all following steps.

Step 3

• Find the start and stop times of each burst in the stored measurement samples.

The start and stop times are defined as the points where the power is at least 30 dB below the

highest value of the stored samples in step 2.

NOTE 2: In case of insufficient dynamic range, the value of 30 dB may need to be reduced

appropriately

Step 4

• Between the start and stop times of each individual burst calculate the RMS power over the burst

using the formula below. Save these Pburst values, as well as the start and stop times for each

burst.

nPk

Pk

nsampleburst

1

1

with 'k' being the total number of samples and 'n' the actual sample number



Step 5

• The highest of all burstP values (value "A" in dBm) will be used for maximum e.i.r.p. calculations.

Step 6

• Add the (stated) antenna assembly gain "G" in dBi of the individual antenna.

• If applicable, add the additional beamforming gain "Y" in dB.

• If more than one antenna assembly is intended for this power setting, the maximum overall antenna

gain (G or G + Y) shall be used.

• The RF Output Power (P) shall be calculated using the formula below:P = A + G + Y

• This value, which shall comply with the limit given in clause 4.3.1.2.3 or clause 4.3.2.2.3, shall be

recorded in the test report.

3.5. Test Result GFSK

Test Condition Total e.i.r.p ( dBm )

CH00 CH19 CH39

T nom (°C) +25℃ V nom (V) 5 2.99 2.90 2.15

T min (°C) -40℃ V nom (V) 5 2.54 2.61 2.05

Tmax (°C) +85℃ V nom (V) 5 2.87 2.38 2.11

Max EIRP Power 2.99

Limits 20dBm (-10dBW)

Result Complies



4. Power Spectral Density

4.1. Test equipment

Item Equipment Manufacturer Model No. Serial No. Calibrated until Cal. Interval

1 Spectrum analyzer

KEYSIGHT N9010A MY55150427 05/25/2019 1Y

2 RF Cable Micable C10-01-01-1 100309 12/17/2018 1 Y


4.3. Limit According to ETSI EN 300 328 V2.1.1 (2016-11) §4.3.2.3, For equipment using wide band modulations

other than FHSS, the maximum Power Spectral Density is limited to 10 dBm per MHz.

PC

(Test Software)

SpectrumAnalyzer

EUT




Connect the UUT to the spectrum analyser and use the following settings:

• Start Frequency: 2 400 MHz

• Stop Frequency: 2 483,5 MHz

• Resolution BW: 10 kHz

• Video BW: 30 kHz

• Sweep Points: > 8 350

NOTE: For spectrum analysers not supporting this number of sweep points, the frequency band

may be segmented.

• Detector: RMS

• Trace Mode: Max Hold

• Sweep time: 10 s; the sweep time may be increased further until a value where the sweep time

has no impact on the RMS value of the signal.

For non-continuous signals, wait for the trace to stabilize.

Save the data (trace data) set to a file.

Step 2:

For conducted measurements on smart antenna systems using either operating mode 2 or operating

mode 3 (see clause 5.1.3.2), repeat the measurement for each of the transmit ports. For each sampling

point (frequency domain), add up the coincident power values (in mW) for the different transmit chains and

use this as the new data set.

Step 3:

Add up the values for power for all the samples in the file using the formula below.

nPPk

nsamplesum

1

with 'k' being the total number of samples and 'n' the actual sample number

Step 4:

Normalize the individual values for power (in dBm) so that the sum is equal to the RF Output Power

(e.i.r.p.) measured in clause 5.3.2 and save the corrected data. The following formulas can be used:

priesumCorr PPC ...

CorrSampleSamplecorr CnPnP

with 'n' being the actual sample number



Step 5:

Starting from the first sample nPSamplecorr (lowest frequency), add up the power (in mW) of the following

samples representing a 1 MHz segment and record the results for power and position (i.e. sample #1 to

sample #100). This is the Power Spectral Density (e.i.r.p.) for the first 1 MHz segment which shall be

recorded.

Step 6:

Shift the start point of the samples added up in step 5 by one sample and repeat the procedure in step 5

(i.e. sample #2 to sample #101).

Step 7:

Repeat step 6 until the end of the data set and record the Power Spectral Density values for each of the

1 MHz segments.

From all the recorded results, the highest value is the maximum Power Spectral Density for the UUT. This

value, which shall comply with the limit given in clause 4.3.2.3.3, shall be recorded in the test report.

4.5. Test result

Test mode Channel

frequency (MHz)

Power Density

(dBm/MHz)

Limit (dBm/MHz)

Test Result

GFSK

CH00 0.76 10 PASS

CH19 0.57 10 PASS

CH39 0.87 10 PASS



GFSK Low Channel

GFSK

Middle Channel



GFSK High Channel



5. Occupied Channel Bandwidth

5.1. Test equipment


1 Spectrum analyzer

KEYSIGHT N9010A MY55150427 05/25/2019 1Y



5.3. Limits The Occupied Channel Bandwidth shall fall completely within the band given in clause 1.

In addition, for non-adaptive equipment using wide band modulations other than FHSS and with e.i.r.p

greater than 10 dBm, the occupied channel bandwidth shall be less than 20 MHz.


Connect the UUT to the spectrum analyser and use the following settings:

• Centre Frequency: The centre frequency of the channel under test

• Resolution BW: ~ 1 % of the span without going below 1 %

• Video BW: 3 × RBW

• Frequency Span for frequency hopping equipment: Lowest frequency separation that is used within

the hopping sequence

• Frequency Span for other types of equipment: 2 × Nominal Channel Bandwidth (e.g. 40 MHz for a

20 MHz channel)

• Detector Mode: RMS

• Trace Mode: Max Hold

• Sweep time: 1 s

Spectrum Analyzer

EUT



Step 2:

Wait for the trace to stabilize.

Find the peak value of the trace and place the analyser marker on this peak.

Step 3:

Use the 99 % bandwidth function of the spectrum analyser to measure the Occupied

Channel Bandwidth of the UUT.This value shall be recorded.

NOTE: Make sure that the power envelope is sufficiently above the noise floor of the analyser to

avoid the noise signals left and right from the power envelope being taken into account by

this measurement.

5.5. Test Result

EUT Set Mode CH or

Frequency

99% dB bandwidth Test Result Result (MHz)

BLE CH00 1.05 PASS

CH39 1.06 PASS



GFSK(CH00)

GFSK(CH39)



6. Transmitter unwanted emissions in the out-of-band domain

6.1. Test equipment


1 Spectrum analyzer

KEYSIGHT N9010A MY55150427 05/25/2019 1Y



6.3. Limits The transmitter unwanted emissions in the out-of-band domain but outside the allocated band, shall not exceed the values provided by the mask in figure 1. NOTE: Within the 2 400 MHz to 2 483,5 MHz band, the Out-of-band emissions are fulfilled by compliance with the Occupied Channel Bandwidth requirement in clause 4.3.2.7.

Temperature and Humidity Chamber

EUT

Spectrum Analyzer

DC Power Supply






•Connect the UUT to the spectrum analyser and use the following settings:

- Centre Frequency: 2 484 MHz

- Span: 0 Hz

- Resolution BW: 1 MHz

- Filter mode: Channel filter

- Video BW: 3 MHz

- Detector Mode: RMS

- Trace Mode: Max Hold

- Sweep Mode: Continuous

- Sweep Points: Sweep Time [s] / (1 μs) or 5 000 whichever is greater

- Trigger Mode: Video trigger

NOTE 1: In case video triggering is not possible, an external trigger source may be used.

- Sweep Time: > 120 % of the duration of the longest burst detected during the

measurement of the RF Output Power

Step 2: (segment 2 483,5 MHz to 2 483,5 MHz + BW)

• Adjust the trigger level to select the transmissions with the highest power level.

• For frequency hopping equipment operating in a normal hopping mode, the different hops

will result in signal bursts with different power levels. In this case the burst with the highest power

level shall be selected.

• Set a window (start and stop lines) to match with the start and end of the burst and in

which the RMS power shall be measured using the Time Domain Power function.

• Select RMS power to be measured within the selected window and note the result which is

the RMS power within this 1 MHz segment (2 483,5 MHz to 2 484,5 MHz). Compare this value with

the applicable limit provided by the mask.

•Increase the centre frequency in steps of 1 MHz and repeat this measurement for every 1

MHz segment within the range 2 483,5 MHz to 2 483,5 MHz + BW. The centre frequency of the last 1

MHz segment shall be set to 2 483,5 MHz + BW - 0,5 MHz (which means this may partly overlap with

the previous 1 MHz segment).

Step 3: (segment 2 483,5 MHz + BW to 2 483,5 MHz + 2BW)

• Change the centre frequency of the analyser to 2 484 MHz + BW and perform the

measurement for the first 1 MHz segment within range 2 483,5 MHz + BW to 2 483,5 MHz + 2BW.

Increase the centre frequency in 1 MHz steps and repeat the measurements to cover this whole

range. The centre frequency of the last 1 MHz segment shall be set to 2 483,5 MHz + 2 BW - 0,5

MHz (which means this may partly overlap with the previous 1 MHz segment).



Step 4: (segment 2 400 MHz - BW to 2 400 MHz)

• Change the centre frequency of the analyser to 2 399,5 MHz and perform the measurement

for the first 1 MHz segment within range 2 400 MHz - BW to 2 400 MHz Reduce the centre frequency

in 1 MHz steps and repeat the measurements to cover this whole range. The centre frequency of the

last 1 MHz segment shall be set to 2 400 MHz - BW + 0,5 MHz (which means this may partly overlap

with the previous 1 MHz segment).

Step 5: (segment 2 400 MHz - 2BW to 2 400 MHz - BW)

• Change the centre frequency of the analyser to 2 399,5 MHz - BW and perform the

measurement for the first 1 MHz segment within range 2 400 MHz - 2BW to 2 400 MHz - BW.

Reduce the centre frequency in 1 MHz steps and repeat the measurements to cover this whole

range. The centre frequency of the last 1 MHz segment shall be set to 2 400 MHz - 2BW + 0,5 MHz

(which means this may partly overlap with the previous 1 MHz segment)

Step 6:

•In case of conducted measurements on equipment with a single transmit chain, the

declared antenna assembly gain "G" in dBi shall be added to the results for each of the 1 MHz

segments and compared with the limits provided by the mask given in figure 1 or figure 3. If more

than one antenna assembly is intended for this power setting, the antenna with the highest gain shall

be considered.

• In case of conducted measurements on smart antenna systems (equipment with multiple

transmit chains), the measurements need to be repeated for each of the active transmit chains. The

declared antenna assembly gain "G" in dBi for a single antenna shall be added to these results. If

more than one antenna assembly is intended for this power setting, the antenna with the highest gain

shall be considered. Comparison with the applicable limits shall be done using any of the options

given below:

- Option 1: the results for each of the transmit chains for the corresponding 1 MHz

segments shall be added. The additional beamforming gain "Y" in dB shall be added as well and the

resulting values compared with the limits provided by the mask given in figure 1.

- Option 2: the limits provided by the mask given in figure 1 shall be reduced by

10 × log10(Ach) and the additional beamforming gain "Y" in dB. The results for each of the transmit

chains shall be individually compared with these reduced limits.

NOTE 2: chA refers to the number of active transmit chains.

It shall be recorded whether the equipment complies with the mask provided in figures 1



6.5. Test Result GFSK

Channel frequency 2402MHz 2480MHz

Test Condition

OOB Emission(MHz) OOB Emission(MHz) 2400-BW

~2400 2400-2BW ~2400-BW

2483.5 ~ 2483.5+BW

2483.5+BW ~2483.5+2BW

Maximum power (dBm)

Maximum power (dBm)

Maximum power (dBm)

Maximum power (dBm)

T nom (°C) 25℃ V nom (V) 3 -52.27 -56.06 -56.70 -57.87

Limits -10.00 -20.00 -10.00 -20.00

Result PASS PASS PASS PASS



Low channel Test Plot

High channel Test Plot



7. Receiver Blocking

7.1. Test equipment

Item Equipment Manufacturer Model No. Serial No. Calibrated

until Cal. Interval

1 Wideband Radio Communication

Tester R&S CMW500 144819 05/25/2019 1Y

2 Spectrum analyzer KEYSIGHT N9010A MY55150427 05/25/2019 1 Y

3 MXG Vector

Signal Generator

N5182B KEYSIGHT MY53052051 05/25/2019 1 Y

4 EXG

analog signal source

N5171B KEYSIGHT M53051415 05/25/2019 1 Y


7.2. Test setup



7.3. Limits Receiver Blocking parameters receiver category 2 equipment

The minimum performance criterion shall be a PER less than or equal to 10 %

7.4. Test procedure

Measurement

Conducted measurement Radiated measurement

Step 1: The UUT shall be set to the lowest operating channel.

Step 2: The blocking signal generator is set to the first frequency as defined in the appropriate table corresponding to the receiver category and type of equipment.

Step 3: With the blocking signal generator switched off, a communication link is established between the UUT and the associated companion device using the test setup shown in figure 6. The attenuation of the variable attenuator shall be increased in 1 dB steps to a value at which the minimum performance criteria as specified in clause 4.3.1.12.3 or clause 4.3.2.11.3 is still met. The resulting level for the wanted signal at the input of the UUT is Pmin.

This signal level (Pmin) is increased by the value provided in the table corresponding to the receiver category and type of equipment.

Step 4: The blocking signal at the UUT is set to the level provided in the table corresponding to the receiver category and type of equipment. It shall be verified and recorded in the test report that the performance criteria as specified in clause 4.3.1.12.3 or clause 4.3.2.11.3 is met.



Step 5: Repeat step 4 for each remaining combination of frequency and level for the blocking signal as provided in the table corresponding to the receiver category and type of equipment.

Step 6: Repeat step 2 to step 5 with the UUT operating at the highest operating channel.

7.5. Test Result

EUT Channel

Blocking signal Frequency

Blocking signalPower Performance Criteria Test Result Result

(MHz) (MHz) (dBm)

Low

2380 -57 PER less than 10 % 0.15% PASS

2503.5 -57 PER less than 10 % 0.38% PASS



High







8. Transmitter unwanted emissions in the spurious domain

8.1. Test equipment

Item Equipment Manufacturer Model No. Serial No.

Calibrated until

Cal. Interval

1 EMI Test Receiver

R&S ESCI 101307 12/17/2018 1Y

2 Spectrum analyzer

Agilent E4407B US40240708 07/03/2019 1Y

3 Trilog Broadband

Antenna Schwarzbeck VULB9168 9168-192 12/17/2018 1Y

4 Double Ridged Horn Antenna

SCHWARZBECK

BBHA 9120D1065

100276 12/17/2018 1Y


SCHWARZBECK

BBHA 9120D1065

100546 12/17/2018 1Y

6 Dipole antenna Schwarzbeck UHAP 1101 12/17/2018 1Y

7 Dipole antenna Schwarzbeck VHAP 1118 12/17/2018 1Y

8 Pre-Amplifier CY EMC011830 980136 12/17/2018 1Y

9 Pre-amplifier HP 8447F 3113A05680 12/17/2018 1Y 10 RF Cable R&S R01 10403 12/17/2018 1Y 11 RF Cable R&S R02 10512 12/17/2018 1Y 12 RF Cable R&S R01 10454 12/17/2018 1Y 13 RF Cable R&S R02 10343 12/17/2018 1Y 14 Signal Generator HP 83732B VS34490501 12/17/2018 1Y

15 Measurement

Software Farad

EZ-EMC (Ver.ATT-03

A) N/A N/A N/A




8.3. Limits The transmitter unwanted emissions in the spurious domain shall not exceed the values given in table 1. NOTE: In case of equipment with antenna connectors, these limits apply to emissions at the antenna port

(conducted) and to the emissions radiated by the cabinet. In case of integral antenna equipment (without temporary antenna connectors), these limits apply to emissions radiated by the equipment.

8.4. Test Procedure Refer to chapter 5.3.10.2 of ETSI EN 300 328 V2.1.1 (2016-11)

Measurement


The setting of the Spectrum Analyzer

RBW 100K(＜1GHz) / 1M(＞1GHz)

VBW 300K(＜1GHz) / 3M(＞1GHz)



8.5. Tesr Result Below 1 GHz WORST- CASE DATA (1GHz ~ 12.75GHz)

EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Horizontal Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 TX BELOW 1G Test Mode: TX Note:

No. Frequency Reading Correct Result Limit Margin Remark

(MHz) (dBm) Factor(dB) (dBm) (dBm) (dB)

1 52.3912 -53.52 -3.73 -57.25 -54.00 -3.25 peak 2 59.8588 -54.98 -4.44 -59.42 -54.00 -5.42 peak 3 71.8319 -52.32 -5.74 -58.06 -54.00 -4.06 peak 4 131.7576 -57.09 -2.86 -59.95 -36.00 -23.95 peak 5 216.0240 -60.60 -4.11 -64.71 -54.00 -10.71 peak 6 492.4685 -62.16 3.14 -59.02 -54.00 -5.02 peak



EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Vertical Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 TX BELOW 1G Test Mode: TX Note:


(MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) 1 39.7146 -57.24 -3.31 -60.55 -36.00 -24.55 peak 2 44.9004 -56.04 -3.39 -59.43 -36.00 -23.43 peak 3 47.9939 -54.88 -3.45 -58.33 -54.00 -4.33 peak 4 51.6615 -53.84 -3.67 -57.51 -54.00 -3.51 peak 5 59.8588 -54.83 -4.44 -59.27 -54.00 -5.27 peak 6 131.7576 -58.18 -2.86 -61.04 -36.00 -25.04 peak



ABOVE 1 GHz WORST- CASE DATA (1GHz ~ 12.75GHz)

EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Horizontal Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 TX ABOVE 1G Test Mode: TX Note: 2402



1 4818.750 -42.28 -10.72 -53.00 -30.00 -23.00 peak 2 7198.125 -55.94 -3.59 -59.53 -30.00 -29.53 peak 3 8196.875 -59.31 -2.11 -61.42 -30.00 -31.42 peak 4 10605.625 -62.41 1.93 -60.48 -30.00 -30.48 peak 5 11545.625 -62.12 3.39 -58.73 -30.00 -28.73 peak 6 12368.125 -61.64 4.46 -57.18 -30.00 -27.18 peak



EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Vertical Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 TX ABOVE 1G Test Mode: TX Note: 2402


(MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) 1 5230.000 -57.00 -9.10 -66.10 -30.00 -36.10 peak 2 7668.125 -59.40 -2.57 -61.97 -30.00 -31.97 peak 3 8255.625 -59.39 -2.14 -61.53 -30.00 -31.53 peak 4 9783.125 -61.29 -0.15 -61.44 -30.00 -31.44 peak 5 11457.500 -61.55 3.30 -58.25 -30.00 -28.25 peak 6 12368.125 -61.82 4.46 -57.36 -30.00 -27.36 peak















(MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) 1 4965.625 -48.48 -10.05 -58.53 -30.00 -28.53 peak 2 7433.125 -58.93 -3.02 -61.95 -30.00 -31.95 peak 3 8108.750 -59.77 -2.07 -61.84 -30.00 -31.84 peak 4 10664.375 -61.97 2.07 -59.90 -30.00 -29.90 peak 5 11398.750 -61.46 3.24 -58.22 -30.00 -28.22 peak 6 12632.500 -61.92 4.93 -56.99 -30.00 -26.99 peak






1 2968.125 -53.20 -14.54 -67.74 -30.00 -37.74 peak 2 5406.250 -57.17 -8.52 -65.69 -30.00 -35.69 peak 3 7550.625 -58.25 -2.77 -61.02 -30.00 -31.02 peak 4 9724.375 -60.96 -0.32 -61.28 -30.00 -31.28 peak 5 11516.250 -62.15 3.36 -58.79 -30.00 -28.79 peak 6 12162.500 -60.45 4.10 -56.35 -30.00 -26.35 peak



9. Receiver spurious emissions

9.1. Test equipment

Item Equipment Manufacturer Model No. Serial No.

Calibrated until

Cal. Interval

1 EMI Test Receiver

R&S ESCI 101307 12/17/2018 1Y

2 Spectrum analyzer

Agilent E4407B US40240708 07/03/2019 1Y

3 Trilog Broadband

Antenna Schwarzbeck VULB9168 9168-192 12/17/2018 1Y


SCHWARZBECK

BBHA 9120D1065

100276 12/17/2018 1Y


SCHWARZBECK

BBHA 9120D1065

100546 12/17/2018 1Y

6 Dipole antenna Schwarzbeck UHAP 1101 12/17/2018 1Y

7 Dipole antenna Schwarzbeck VHAP 1118 12/17/2018 1Y

8 Pre-Amplifier CY EMC011830 980136 12/17/2018 1Y

9 Pre-amplifier HP 8447F 3113A05680 12/17/2018 1Y 10 RF Cable R&S R01 10403 12/17/2018 1Y 11 RF Cable R&S R02 10512 12/17/2018 1Y 12 RF Cable R&S R01 10454 12/17/2018 1Y 13 RF Cable R&S R02 10343 12/17/2018 1Y 14 Signal Generator HP 83732B VS34490501 12/17/2018 1Y

15 Measurement

Software Farad

EZ-EMC (Ver.ATT-03

A) N/A N/A N/A




9.3. Limits

The spurious emissions of the receiver shall not exceed the values given in table 2. NOTE: In case of equipment with antenna connectors, these limits apply to emissions at the antenna port

(conducted) and to the emissions radiated by the cabinet. In case of integral antenna equipment (without temporary antenna connectors), these limits apply to emissions radiated by the equipment.

9.4. Test Procedure Refer to chapter 5.3.11.2 of ETSI EN 300 328 V2.1.1 (2016-11)

Measurement


The setting of the Spectrum Analyzer

RBW 100K(＜1GHz) / 1M(＞1GHz)

VBW 300K(＜1GHz) / 3M(＞1GHz)



9.5. Test Result BELOW 1 GHz (30 MHz ~ 1GHz)

EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Vertical Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 RX BELOW 1G Test Mode: RX Note:






EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55% Distance: 3m Test Power: DC 5V Polarization: Horizontal Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 RX BELOW 1G Test Mode: RX Note:






ABOVE 1 GHz (1GHz ~ 12.75GHz) EUT: CALM. Module Model No.: SVN-840C Temperature: 24 　 Relative Humidity: 55%

Distance: 3m Test Power: DC 5V Polarization: Horizontal Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 RX ABOVE 1G Test Mode: RX Note: 2402



1 2968.125 -53.38 -14.54 -67.92 -47.00 -20.92 peak 2 6728.125 -57.79 -4.95 -62.74 -47.00 -15.74 peak 3 8255.625 -58.88 -2.14 -61.02 -47.00 -14.02 peak 4 10458.750 -62.27 1.57 -60.70 -47.00 -13.70 peak 5 11398.750 -61.35 3.24 -58.11 -47.00 -11.11 peak 6 12661.875 -61.48 4.97 -56.51 -47.00 -9.51 peak



EUT: Model No.: Temperature: 24 　 Relative Humidity: 55%

Distance: 3m Test Power: DC 5V Polarization: Vertical Test Result: Pass Test Time: 2018-11-12 Test By: Standard: EN 300328 RX ABOVE 1G Test Mode: RX Note: 2402



1 2968.125 -53.70 -14.54 -68.24 -47.00 -21.24 peak 2 5905.625 -56.80 -7.94 -64.74 -47.00 -17.74 peak 3 6933.750 -56.75 -4.30 -61.05 -47.00 -14.05 peak 4 8373.125 -59.06 -2.19 -61.25 -47.00 -14.25 peak 5 10576.250 -61.77 1.85 -59.92 -47.00 -12.92 peak 6 12720.625 -61.48 5.08 -56.40 -47.00 -9.40 peak

Note: Only the worst data were recorded in this report.



10. Test setup photograph



11. EUT photograph



END OF REPORT

Documents

ETSI EN300 328 RADIO TEST REPORT...2018/12/18 · Pressure range 86-106kPa 86-106kPa Power supply DC 3.7V DC 3.15V and DC 4.26V Note 1: The HT 55°C and LT -20°C was declarated by