Error Message System Requirements - Snap-on DSS ScanBay Software automatically checks your personal computer (PC) to make sure it is ready to be upgraded (Figure 3)

DSS ScanBay Software Installation Instructions

© 2009 SNAP-ON INCORPORATED, ALL RIGHTS RESERVED5

The ready to install screen displays (Figure 12).

Figure 12 Sample ready to install screen

13. Press Install and wait for the installation to begin (Figure 13).

Figure 13 Sample installation progress screen

14. When the Completing the DSS ScanBay Setup Wizard message displays, press Finish (Figure 14).

Figure 14 Sample completing screen



When the installer window closes, the process is complete. Remove the DSS ScanBay Installation disc from the CD-ROM drive and store it in a safe place for future use.

IMPORTANT:After installing the DSS ScanBay Software, please perform a DSS Send/Receive E-mail to register the installation, and to obtain any remote updates that may be available for DSS ScanBay.

Error MessageThough unlikely, if a No Disk error message displays during the installation process (Figure 15), press Cancel to continue.

Figure 15 Sample setup.exe - No Disk error message

© 2009 SNAP-ON INCORPORATED, ALL RIGHTS RESERVED—EAZ0030B21F Rev.A

This document provides instructions for installing DSS ScanBay™ software on your new Dealer Sales System (DSS) and new Multiple Franchise System (MFS) computers.

System Requirements• Operating System:

- Microsoft® Windows XP Professional Service Pack 2 (recommended)- Windows 2000 Professional Service Pack 4 (minimum)

IMPORTANT:DSS ScanBay does not support Microsoft® Windows Vista.

• Sales System:- Special Representative Sales (SRS): Version 7.90 (recommended), 7.80 (minimum)- Dealer Sales System (DSS): Version 7.90 (recommended), 7.80 (minimum)- Multiple Franchise System (MFS): Version 7.90 (recommended), 7.80 (minimum)

• ScanBay™ Programming Equipment:- VCI/TSI cartridge programmer- CompactFlash® card reader/writer- Mini USB cable

Installation InstructionsUse the following procedure to install the DSS ScanBay Software on your computer.

z To install the software:1. Close all applications, including any virus or security software.2. Exit all sales system software.3. Insert the DSS ScanBay Installation disc into your CD-ROM drive.

The installation program automatically starts.If the installation does not automatically start do the following:a. From the Windows desktop, select Start > Run (Figure 1).

Figure 1 Sample Windows Start menu selection

DSS ScanBay™ Software Installation Instructions



The Run dialog box displays (Figure 2).

Figure 2 Sample Run dialog box

b. In the Open field, type D:\Setup.exe, unless “D” is not the letter assigned to your CD-ROM drive, in which case, substitute the letter assigned to your CD-ROM drive in place of “D”.

c. Press OK, and the installation program begins.4. The DSS ScanBay Software automatically checks your personal computer (PC) to make

sure it is ready to be upgraded (Figure 3).

Figure 3 Sample PreInstall Actions screen

5. If your personal computer (PC) was not upgraded to DSS ScanBay 7.2 Software, a NET 2.0 Framework upgrade begins automatically (Figure 4).

Figure 4 Sample Net 2.0 Framework upgrade screen

NOTE:i The progress bar on the NET 2.0 Framework window quickly goes about halfway, then

stops. This is normal, the program has not stalled. The screen may hold in this position for several minutes before the progress bar begins tracking again. Do not cancel.

6. A WSE Runtime runtime upgrade immediately follows the PreInstall Actions or the NET 2.0 Framework upgrade (Figure 5).

Figure 5 Sample WSE Runtime upgrade screen

The software installation, which is a two-stage process, begins immediately after the Preinstall Actions are complete. The first stage installs the USB Setup Utility, the second stage installs the actual DSS ScanBay software update.

7. The USB Setup Utility welcome screen displays after the runtime upgrades (Figure 11).



Figure 6 Sample USB Setup Utility Welcome screen

8. Press Next.The ready to install screen displays (Figure 7).


9. Press Install to begin the installation (Figure 8).

Figure 8 Sample installation in progress screen

A copying files screen displays after the installation is complete (Figure 9).



Figure 9 Sample copying files screen

A message displays when the USB Setup Utility installation is complete (Figure 10).

Figure 10 USB Setup Utility complete screen

10. Press Finish to end the USB Setup Utility Operation and begin stage two.11. The DSS ScanBay installation welcome screen displays (Figure 11).

Figure 11 Sample installation welcome screen

12. Press Next to continue.





















































































































Documents

Error Message System Requirements - Snap-on DSS ScanBay Software automatically checks your personal computer (PC) to make sure it is ready to be upgraded (Figure 3)