Error Codes

Details for Error code E00/0000Xbox freezes after showing the first digit of the

Add / Edit

Details

Primary Error code: 3 RLODE-Code / Secondary Error code: E00 (No Audio/Video) / 0000

Binary/Hex: 00000000 / 0x00 -> 0Known fixes:

1) Blow the dust away under the Southbridge and HANA chip2) Reflow the Southbridge3) X-Clamp replacement

Related Errors:No Related Errors available!

Description:The Xbox doesnt know whats wrong it freezes after showing the first digit(0) of the error code.Might be a cold solder joint somewhere under the GPU as someone fixed it with the X-Clamp replacement, might also be scaler or Southbridge related since this is where the error code is calculated...

According to stephen.a.j it can also be caused by dust under the Southbridge and the HANA chip so please check for that...

Add / Edit

Comments for this Error code:

bigart666 on 2010-09-22 09:16:49 :

had this error 3 times(3 boxes) tried re-flowing hana sb nothing re flowed gpu 2of them worked had a stubborn one re-flowed gpu couldn't fix so i added

shim and screw set under gpu as last resort added 2 washers on 3 on top then 1on 4th screw played around with the tighten each one loosen so on boom it worked

steoc on 2010-03-09 15:14:01 :

I think this is an 0102 cold joint under the southbridge or GPU, sometimespressing eject twice fast gives a 1 and pressing it once gives a 0 so it could

be 0102, 0103, 0110 but you get 0 and 1 out of it and thats all it keepsresetting back to the first 0 when eject is pressed once.

Details for Error code E01/0001Short circuit in the console/faulty PSU

Add / Edit

Details



1) Make sure your PSU is working and replace it if it isnt2) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that move out of place while heatgunning, etc.3) Replace MOSFETs and regulators that are known to cause it if they were blown4) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.5) Reflow the CPU, HANA chipIn rare cases a reflow might also fix it.6) X-Clamp replacementThe GPU heatsink might be shorting out if you screwed it in too tight...


Description:This error can be triggered by a faulty power supply or a short in the console. The short is located near one of the main supply lines, so mostly not under the chips, it might also be a blown capacitor fuse or just a bridged contact. Also damaged DVD power cable.

Add / Edit

Comments for this Error code:sky1987 on 2010-12-24 19:58:46 :

You may get this error if you have not fully pushed the power cable into thepower port. Ensure the cable is pushed in as far as it can go (You will hear a

click in most cases when it's pushed far enough).

koriashi on 2010-11-04 05:25:18 :ok, so im getting this error code but as SOON as I turn it on the power supplyclicks and flashes red for like a half second then goes back orange. I get no

fan or dvd action. I checked all over the motherboard and I didnt find anythingwrong. Idk if its the MOSFETS because I have no way of checking them. jus

wondering if anybody knows why the psu led just flashes one time and goes backto orange.. thanks

koriashi on 2010-11-04 05:22:58 :ok, so im getting this error code but as SOON as I turn it on the power supplyclicks and flashes red for like a half second then goes back orange. I get no

fan or dvd action. I checked all over the motherboard and I didnt find anythingwrong. Idk if its the MOSFETS because I have no way of checking them. jus

wondering if anybody knows why the psu led just flashes one time and goes backto orange.. thanks

Details for Error code E02/0002Cold solderjoint under CPU

Add / Edit

Details



1) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that moved out of place while reflowing, etc. - Especially in the CPU area3) Replace MOSFETs and regulators that are known to cause it if they were blown4) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.5) Reflow the CPU6) X-Clamp replacement


Description:This error code is caused by a cold solder joint under the CPU or by a problem with the way it is powered(blown mosfet, capacitor or a short)According to xbox-scene it is also a problem with the ethernet chip but there arent any references for that.

Add / Edit

Comments for this Error code:adolfoambriz on 2010-11-28 02:18:25 :

I just did this hybrid X clamp mod to my XBOX and it did worked for a couple ofdays, but now I have this 102 code and 1 red light light. What can it be, or

what possible whent wrong? I would appreciate if I get a good answer and not goof coarse with other comments because its very important for me to find an

answer quick.

luigirez1 on 2010-10-19 22:27:07 :Can also be caused by a transistor breaking off and being replace by a solderbridge. It also happened when a short is created by the motherboard cage. I

fixed that by putting electrical tape on the bottom of the cage where themotherboard touches.

mynamesuxlol on 2010-10-10 21:02:58 :Can also be caused by southbridge, i would apply pressure, then 0002 is gone, i

take away the pressure > 0002

babyface015 on 2010-03-23 19:17:29 :I had this problem with mine xbox, and i solved this problem by just adding some

thermal compount onder the CPU, i don't know if this always solves thisproblem

killrhedake on 2010-01-07 23:28:56 :This also occurs when the washers used in an X-clamp mod are too large. It

causes a bridge between the GPU and CPU heatsink. Using plastic washers orreverting to the stock x-clamps will combat this error.

Details for Error code E03/0003

Power problem/ Cold solder joint under CPU

Add / Edit

Details



1) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that moved out of place while reflowing, etc. - Especially in the CPU area2) Replace MOSFETs and regulators that are known to cause it if they were blown3) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.4) Reflow the CPU5) X-Clamp replacement

Related Errors:0001

Description:The CPU is somehow not getting clean power, can be a cold solder joint under it or one of the external parts like a missing cap etc.

Add / Edit


dmcbudman on 2010-07-27 05:35:10 :

i can confirm that 0003 on a falcon is a gpu problem.same as solidwars e74

while reflowing to fix the e74 one of the balls popped out from under the gpu(iknow...its the first time i ever saw that happen)

solidwars on 2010-05-21 20:17:27 :

I had this same problem after heat gun reflow on E74 error it gave me 3 RRODsecondary code 0003. I tried loosening the CPU heatsink it made no difference

then i tried the GPU heatsink and it started up. It was working but i wasnthappy with looseness of the heatsink against mobo so decided to try nylon

washers (slightly thicker) with metal ones on top. No idea how long it will lastbut working for 3 days proper use so far.

nzlab on 2010-05-16 19:56:48 :

Some of the boards that I've experimented with, 0003 occurred after ikilled the GPU.

Details for Error code E04/0010Cold solder joint under Southbridge

Add / Edit

Details



1) Southbridge X-Clamp-Fix2) Reflow the Southbridge area3) Check the area under the Southbridge for parts that might have fallen off and solder them back on.


Description:There is a problem with the Southbridge Chip usually dealing with how it connects to the mainboard (cold solder joint/bridged solder joints)(Taken from Xbox-Scene)

Add / Edit

Comments for this Error code:mynamesuxlol on 2010-09-07 06:47:41 :

Also can be JTAG related, such as a short, double check wires

mynamesuxlol on 2010-09-07 06:47:24 :Also can be JTAG related, such as a short, double check wires

cdrom20 on 2010-06-09 01:51:40 :You're screwd... I have little success removing the e73 error, and usually

the mother board is trashed with this error.

austn0489 on 2009-12-22 00:46:47 :i am having this exact problem. I have tried to reflow the southbridge but with

no luck. Any known working alternate fixes for this?

austn0489 on 2009-12-22 00:44:49 :i am having this exact problem. I have tried to reflow the southbridge but with

no luck. Any known working alternate fixes for this?

Details for Error code E08/0020Bridged solderjoint/Short - CPU/GPU/RAM

Add / Edit

Details



1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the GPUAlso look for missing/bridged components like capacitors/resistors2) If you jtagged the console remove wires and resistors, the parallel port can stay as long as no PC is connected.3) X-Clamp replacement4) Flush with alcohol, let dry, begin Relow with flux like below 5) Reflow GPU (and RAM if this fails) area6) Reball the GPU and RAM, for bridged solder


Description:This error is caused by a bridged solder joint under CPU, GPU or one of the RAM bricks.This effect can also be caused by tin whiskers leading to shorts and if the GPU was taken off the mainboard this error will also show up.It can also be power related(the CPU/GPU or RAM isnt getting enough power). Can also be a component that is missing or damaged so look for missing and bridged parts near the GPU.If the console was jtagged and the resistors and cables are still connected it will show 0020, the parallel port can stay as long as no PC is connected.

Add / Edit

Comments for this Error code:domn8r81 on 2010-11-30 05:54:31 :

Any thoughts? She was working tip-top, no graphics issues and then at the 45min. mark it was like...1 second of green bars and then auto cut-off. Is it

possible that the unit loosened-up with heat and I just need to tighten up theheat sinik screws? Also, if I don't do anything can I expect depreciating

game-time? Sorry for the thesis, but I appreciate any feedback you guys canoffer.

domn8r81 on 2010-11-30 05:45:46 :Older unit been using it for the last two years in Caribbean (can u say

humid?). Began locking-up and graphics issues culminating in 0102. While in 3rdworld performed a real hack job replacing the x-clamps (didn't have stuff

and made washers using abalone guitar picks). Got about 4 hours of play out ofit but then that was it.

Now back in the US, serious about the fix. Did a hybrid and the secondarychanged from 0102 to a 0020. Read more (great info on this site guys, keep it

up) and did a low-temp oven bake. Debated doing a flux flush and oven reflow orheat gun but decided to put her back 2-gether and giver a go. Got 45 min. and

then 2rod shutdown.

She rebooted fine after a little rest but thinking Flux and reflow? thx!

Silvarion on 2010-11-29 17:52:25 :

This error also comes when there is a short on dvd board like a bad tracesoldering on LiteOn drive. I saw 0021 from a damaged LiteON PCB from screw

over-tightening while the PCB was misaligned.

halo3 on 2010-11-10 03:37:43 :Can also just be some dust buildup in your 360, just blow it out and clean it.

I've had this in some cases, so it's not an oddity. -halo3

v41p3r on 2010-08-11 07:40:44 :So first do the xClapmFix and if it still doesn't work - on the tutorial i

saw you had to put 2 washes on each bolt on the upper side of the motherboard,so if yours is the same remove 1 from each bolt only from the ones that hold the

GPU cooler thingy and screw it real tight ( sorry for my bad english - i'mbulgarian after all :D:D )

Wilhelm on 2010-06-30 03:28:50 :If it is a natural 0020 it is tin whiskers in most cases thats why

overheating(DONT DO THAT) or reflowing the solder balls fixes it.The tin whiskers are just ultrathin antennas so when they get hot the top parts

break off or if they actually reflow they will be sucked up by the solder..

NickdogV on 2010-06-09 06:11:50 :I do not believe this 0020 Error code is a bridged solder joint because I repair

these all the time. Usually a bridged solder joint involves luck to getrepaired using a reflow station instead of using reballing equipment. 0020 is

most likely caused by a cold solderjoint underneath the GPU that can be repairedwith a heatgun/griddle.

killrhedake on 2010-05-18 09:40:04 :I successfully relieved a twentied console last week. Initially I found I could

get it to boot with additional pressure on the GOU heatsink but only toward theCPU heatsink. I did the xclamp mod on GPU side only and tightened the hell outof the GPU heatsink, like as hard as I could with my hands alone, and voila! It

has worked like a charm ever since.

hargabyte on 2010-04-24 09:23:21 :I got this error after doing a reflow for a 0102 error. has hybrid xclamp on it.

I loosened the screws a little and it works fine now. I think it was just ashort caused by the heatsink

Lythius on 2010-02-12 20:28:48 :I have resolve this Problem ( 0020 ) semply replace the IC regulator IC Q2G1 (

near Eject switch ) becasue is "open and loss". Try It! Work!!! (sorry for my Bad English I'am Italian ) ;)

bigart666 on 2010-02-11 03:16:48 :i fixed one today 0020 flush chips with alcohol griddle underneath heatgun low380(f) 3 minutes then high 480(f) 500(f) 2 minutes let cool hybrid bam works

Griff on 2010-02-01 08:48:21 :the worst error ever!

Arbosia on 2010-01-11 03:17:06 :I receive this Ecode after attempting to use the penny trick on an E18/0102.

Ram>Thermal>Penny>Thermal>Heatsink

Jimbobjoeyman on 2010-01-05 14:40:55 :this error code sucks

Details for Error code E09/0021

Bridged solderjoint/Short - GPU/Southbridge

Add / Edit

Details



1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the SouthbridgeAlso look for missing/bridged components like capacitors/resistors2) X-Clamp replacement3) Southbridge X-Clamp-Fix4) Reflow the Southbridge/Ethernet chip area5) Reball the Southbridge - bridged solder6) if you work in dumping lite-on 8xxxx and 9xxxx with jumper, Check your dvd drive pcb (board) again, if there's still some shorting.

Related Errors:1021

Description:This error is caused by a bridged solder joint under GPU or Southbridge. It can also be power related(the Southbridge isnt getting enough power). Can also be a component that is missing or damaged so look for missing and bridged parts(caps etc) near the Southbridge

Add / Edit

Comments for this Error code:Silvarion on 2010-11-29 17:59:51 :

Got this one on a LiteON 7xxxx with cracked/broken PCB on the screw near thecorner. Also 0020 on another with bridged solder on a trace that was cut.

crossedflags78 on 2010-09-06 21:37:49 :IF you trying to JTAG a falcon and it gives you this code after you wired the

jumpers then check the jumper from j2d2 4 and 7. It may draw too much currentand trip the error.

Simply put a diode, 1n4148, same diode as the other 2, with the cathode (black side) towards pin 4 in place of the jumper.

This post has more details: www.xboxhacker.org/index.php?topic=15779.0

crossedflags78 on 2010-09-06 20:23:35 :IF you trying to JTAG a falcon and it gives you this code after you wired the

jumpers then check the jumper from j2d2 4 and 7. It may draw too much currentand trip the error.

Simply put a diode, 1n4148, same diode as the other 2, with the cathode (blackside) towards pin 4 in place of the jumper.

gepal on 2010-02-11 00:37:56 :I had one Jasper with 93450c, and error was found in connector at dvd-rom side.

When console were powered on there was no (specific start-up) sound ofdvd-drive.

The solution for this problem was to bend a little bit (absolutely very little)to center on both pin lines. I wanted to be sure that there IS connection with

every pin.

Details for Error code E10/0022Bridged solder joint/Short GPU-> (H)ANA

Details


Binary/Hex: 00001010 / 0x0A -> 10Known fixes:

1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.2) X-Clamp replacement3) Reflow GPU and HANA chip4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.6) also can be caused by a broken trace (see link below).


Description:This error is caused by a bridged/shorting solder joint under the GPU, (H)ANA-chip or in between.It can also be power related though, for example if you are drawing power from one of the regulators that power the GPU and HANA-chip.Can also be a component that is missing or damaged so look for missing parts near the GPU and the HANA chip. In extremely rare cases it might also be related to the lines that lead from HANA to the CPU.The chances are however higher that it is the GPU than the HANA chip so you should always first concentrate on the GPU.

Another cause could be due to a broken trace under the board near one of the ram blocks, check the picture in the reference section. Thank you arvydas for reporting this solution!

Comments for this Error code:Liam on 2010-10-12 22:19:52 :

i have this on my jtagged xbox 360 it happened jus after i flashed with Flash360how can i flash back to my original when i cant get on xell if any1 can help me

aim me blueinc678 or msn [email protected] (ive tried step1-4)

btw the old gpus have broken corners - check yours with a microscope.

texasproxmodsxe on 2010-07-02 04:37:33 :also if you tighten the screws to tight that also might cause this error so

loosen them a bit then try i just went through that right now i loosened screwsthen boom green lights

texasproxmodsxe on 2010-06-24 09:28:19 :ive just reflowed a 0022 with a aouye 852++ rework station just use flux and

good temps the gpu has about 95% of the errors since its the biggest bga

bigace109 on 2010-05-11 22:36:37 :would reballing the gpu be worthwhile? has anyone ever tried this and had

sucess?

maialuis on 2010-03-05 16:17:11 :Boar jasper give tis error some times on start up, but if you wait one minute or

two with console giving error on next start up console boot normaly without thiserror. I try reflow gpu and Hana chip and it worked for a few days.

Details for Error code E11/0023(unknown) probably a short under Southbridge>ANA

Add / Edit

Details


Binary/Hex: 00001011 / 0x0B -> 11Known fixes:

No Known fixes available!Related Errors:

0021

Description:This error is unknown but assumed to be a short either under Southbridge and (H)ANA chip or in between these.Look for 0021 and 0022 and reflow the Southbridge-> HANA chip area, the X-Clamp Fix might help as well.

References:No References available!

Clicks: 10058

Details for Error code E12/0030Temp sensor problem/ Cold solder joint under CPU

Add / Edit

Details


Binary/Hex: 00001100 / 0x0C -> 12Known fixes:

1) Replacing the X-Clamps2) Reflowing the CPUConcentrate on the CPU.3) Cutting the CPUs temp sensor trace.


Description:The temp sensor is not working properly, maybe because it is shorting out (2 bridged solder balls).Or it is broken, then you have to cut the trace...

References:http://forums.xbox-scene.com/index.php?showtopic=484726

Clicks: 8133

Details for Error code E13/0031Faulty RAM brick/ Shorted out resistor

Add / Edit

Details


Binary/Hex: 00001101 / 0x0D -> 13Known fixes:

1) Reflow the RAM and Southbridge2) Loosen your heatsink screws and make sure the heatsink isnt shorting out a capacitor...3) Replace the faulty RAM brick4) X-Clamp replacement5) Replace dvd power cord. Short in the dvd drive cord or the cord is in backwards.6) un-bridged U6T1 or U6T2 (point that protect cpu-fuse)


Description:This error is caused by a faulty/cracked RAM brick, however it can also be caused when the heatsink is shorting out a resistor or like a bad solder joint under the GPU?, check out the links in the references...Also caused by the Southbridge if not properly soldered to motherboard or if it experiences a power short.Can be caused by a backwards power cord or faulty power cord to dvd player.

- if you update to freeboot 9199 with bridged U6T1 or U6T2 this error will appear, unbridged it (Shadow-Wizzard)

References:VendetaxTMxHom3rAll credits for the Southbridge related discoveries go to CanadaTech, thanks a lot.kyledgrant for the DVD-drive cord

Clicks: 32528


devinogden on 2010-11-02 01:14:42 :Resistor short confirmed. Received error after performing x clamp fix.

Investigated board for any signs of the problem and found that the gpu or cpuheatsink (can't quite remember which one) was making contact with a nearbyresistor. I attempted to loosen the screws attached to the heatsink but made it

overheat quickly. To fix this, I removed the heatsinks completely, appliedelectrical tape underneath completely covering under the heatsink except of

course the gpu or cpu chips.

PRiME on 2010-07-26 07:28:56 :I had this error caused by a bad reflow. I reballed the GPU and error was goneso it definitely can be linked to a bridged solder joint under the GPU as well.

If you can't do reballing it may make it a bit hard to fix so perhaps useHIGH grade high quality flux to repair it?

NickdogV on 2010-06-09 05:39:43 :DvD Power Cord Confirmed. I repair about 15-20 xboxs a week here in San Diego,and I came across one that had this 0031 Error Code today. I am just confirming

that I repaired it just by switching out the dvd power cord. Easy $50.

Details for Error code E17/0101USB port (bridged pins)

Details



1) Unplug all USB devices that might be connected to your 3602) Remove solder from the pins under the USB ports so that they are not shorting out anymore, also check the ports themselves and make sure that the pins inside arent bridging


Description:This error is caused by bridged solder joints under the USB ports or a defective USB device that is connected to it.

References:LoKy

Clicks: 20611


luigirez1 on 2010-10-19 22:21:26 :

South bridge reflow fixed it.

luigirez1 on 2010-10-19 22:18:51 :

South bridge reflow fixed it.

elior77 on 2010-08-17 15:40:07 :

SB reball fixed it.

elior77 on 2010-08-16 16:47:50 :

I took off all the USB ports from the mobo and it didnt help...I'm gonna try reball the SB.

and then the GPU.

hargabyte on 2010-04-19 04:38:16 :

had one of these today. usb port had bridge solder. removed it and tada itworked again

Details for Error code E18/0102Cold solderjoint - CPU/GPU/RAM

Details



1) X-Clamp replacement2) Reflow GPU and RAM


Description:This error is caused by a cold solder joint under CPU, GPU or one of the RAM bricks. Can also be a component that is missing or damaged so look for missing parts near the GPU.

Comments for this Error code:espa on 2010-12-08 00:25:43 :

Fixed over a hundred of these with no problems. The GPU just needs to bereflowed using the profile available on here, but you need to leave the griddleon for 30 minutes after the repair. It works everytime. Like I said, over a 100

of these and not one return in 9 months!

texasproxmodsxe on 2010-11-20 22:42:38 :O1O2 ALSO can be scratched trace on board under gpu due to removing x-clamps

with screwdriver

cwailes on 2010-09-29 23:58:48 :If I do the aluminum sheet fix, where do I put it? I assume between the GPU and

the Heat sink?

babyface015 on 2010-08-03 16:03:10 :hi guys

i have this error code on an xbox and ficed it multiple times but it keepscoming back after a week or sow:s does anybody now how i can fix this, i have

done the x-clamp replacement, heatgunt it at 500 degrees celcius, i cut the temptrace beceause that was an error to and i did a 12 volt fan mod. but it keeps

coming back, does anybody know what i'm doing wrong?? please help









NickdogV on 2010-06-09 06:15:37 :This is the most common error code that I see in all the xboxs I repair. About

55-60% of the 3RROD units has this 0102 secondary error code. It is caused by a

cold solder joint underneath the GPU. Heatgun/Griddle will repair these if youknow what you are doing.

hargabyte on 2010-04-19 04:13:29 :I wouldnt suggest putting an aluminum sheet on your gpu. The only reason this

might work is if the heatsink is scratched up. try sanding down your heatsinkwith really fine sandpaper. Also Griff, a hair dryer is now going to help. There

is no way the chip will ever get hot enough. Solder has to reach about 220C tomelt. Thats around 500F.

I have fixed several systems with this error. reflowing the cpu and gpu andreplacing the thermal paste has worked every time for me. I have yet to have one

of these that I couldnt fix

u60n0 on 2010-04-03 23:28:26 :Here you can enter your comment...

Edox on 2010-03-27 23:47:11 :I just was attempting to fix an xbox 360 with a gpu error by reflowing the top

and bottom of the gpu chip. Then, when i put everything back together, the errorwas replaced with this. Would this be an easy fix. I have a heatgun, articsilver 5, and penny's to replace thermal pads. All i ned to know is which

out of all of those will fix this error :D

bigalscot on 2010-01-23 22:27:00 :Have to say i've cooked my MB in oven, changed thermal paste and still get

the RROD 0102. Used aluminum foil on GPU as a last attempt. It works perpectly.

killrhedake on 2010-01-16 05:25:13 :Replace thermal paste. 98% of the time, that is the problem. One of the

heatsinks are touching their chip. No X-clamp Mod necessary. Just replace thethermal paste with Arctic Silver 5.

Griff on 2009-12-15 02:12:31 :Penny fix then heat with classic heirdryer is help me )

focusthis51 on 2009-12-12 00:23:14 :adding an a piece of aluminum sheet to the gpu usually fixes this problem.

Details for Error code E19/0103Cold solderjoint- GPU/ bad cap

Details



1) Remove short circuit from bridged capacitor under the GPU 2) X-Clamp replacement3) Reflow CPU/GPU/RAM

Related Errors:0102

Description:This error can either be caused by a cold solder joint under the GPU or a bridged capacitor under it(power problem)


killersla on 2010-10-15 13:02:20 :

i got this error done xclamp with gpu reflow didnt work at first then loosenedgpu screws and now works fine

Details for Error code E20/0110Cold solder joint -> RAM

Add / Edit

Details



1) Reflow the RAM2) Loosen your heatsink screws and make sure the heatsink isnt shorting out a capacitor...3) Look for missing and bridged components like resisitors and caps and replace them4) X-Clamp replacement


Description:This error is caused by a cold solder joint under one of the RAM chips, mostly its the top ones, sometimes it can also be one of the solder balls under the GPU that lead to the RAM. Update:According to stephen a.j it can also be cause by a broken trace that connects the GPU and the RAM, the reason for it to break could be the flexing in this certain area.

Comments for this Error code:masterfulmatt on 2010-11-25 01:43:28 :

Can confirm this can be caused by heatsink shorting capacitor, cured usingkapton tape to insulate capacitors.

bigart666 on 2010-09-30 01:19:29 :worst error ever pain in ass tried everything had a e71 turn to 0110

Triokon on 2010-08-29 10:36:06 :(I just achieved it that the box didnt show any errors anymore and started withzero green/red lights, but there was only a blackscreen on TV and sounds for

just a few seconds, although the TV turned his screen to 1080p.)Really hard to believe that a RAM chip just breaks, though the xbox was in

normal playing conditions. But it physically happened. [(Part 2 of thecomment)]

Triokon on 2010-08-29 10:35:25 :One of my boxes had this error. In my case it wasn`t a cold solder joint under

one of the RAM chips (4 reflows, a x-clamp-fix and a penny fix would have fixedthat), but a very small brick in a corner of one the RAM chips at the downside

of the board (which looked like a small hair on the chip). I fixed this formaybe an hour by lifting up the broken part of chip at the same height of theother chip with a very small screwdriver. Then the 0110 occured again and I

couldn`t fix it anymore. (Part 1 of the comment)

NickdogV on 2010-06-09 06:18:12 :Reflowing the GPU gets these repaired 80-85% of the time. If it's not theGPU then reflow the RAM. 99% of the time it is the 2 RAM chips directly

underneath the GPU.conker1596 on 2010-02-14 22:25:53 :

i have a 360 and one of the solder joints under a capacitors os broken. is thisthe purpose of the error on my 360?

Details for Error code E21/0111(unknown) probably NAND/RAM?

Add / Edit

Details




0110

Description:This error is unknown but could be somehow related to a cold solder joint under the RAM.On xbox-scene there was also a post in which was claimed that it has to do with the NAND

Comments for this Error code:fantais on 2010-11-25 15:15:54 :

Got this error with Artifacts and Freezing symptoms, reflowed the GPU, worksfine

jerkysmile on 2010-05-21 12:02:44 :Might be too tight bolting of GPUCPU Heatsinks with unpluged or damaged

AVHDMI cable.P.s Sry for grammar mistakes, from Russia with love :D

jerkysmile on 2010-05-21 12:02:24 :might be too tight CPU and GPU Bolting with unplugeddamaged AVHDMI cable.

P.s sry for mistakes, from Russia with love :D

xboxJedi on 2010-02-21 18:22:32 :ATTENTION FRIENDS:

I had the 3RROD with error 0111 and did the following: (NOTE: i have no warrantyand the seal was broken by someone else so do not do this unless you know what

can happen)

REMEMBER TO CLEAN ALL OLD THERMAL PASTE OFF BEFORE DOING ANYTHING ELSE

REFLOW W/HEAT GUN, GRIDDLE & TEMP. GUN ON 4 RAM CHIPS/SOUTHBRIDGE &HANA

THEN THE X-CLAMP FIX TO REPLACE THE CRAPPY X-CLAMPS AND SNUG EVERYTHING DOWNAND TEST:

its been running hours upon hours for me so i hope this helps!

- Jedi

Details for Error code E22/0112(unknown) probably RAM

Add / Edit

Details




0110

Description:This error is totally unknown, probably it is RAM related like 0110


Clicks: 2815

Add / Edit


gammmmes on 2010-05-25 21:23:56 :

I recived this code with 2 rrod. the fans blew strong then right to error. Iadjusted heat sinks. cleaned and new artic silver. applied thermal pads under

ram with penny stuck to them. system runs without sign of problems.

Details for Error code E23/0113(unknown) probably RAM

Add / Edit

Details




0110

Description:This error is totally unknown, probably it is RAM related like 0110


Clicks: 1995

Add / Edit


Details for Error code E24/0120(unknown) short under RAM

Add / Edit

Details



1) Penny fix on RAMRelated Errors:

0110

Description:This error is unknown but someone on xbox-scene could fix it using the penny fix.Could be a short in the area under the RAM that causes 0110 when there is a cold solder joint.If it was like usual the error code would be 0020.


Clicks: 4362

Add / Edit


Details for Error code E25/0121Cold solder joint under CPU

Add / Edit

Details



1) Replacing the X-Clamps2) Reflowing the CPU


Description:Cold solder joint under CPU-> The CPU cant communicate with the mainboard


Clicks: 2054

Add / Edit


Details for Error code E32/0200Cold solder joint GPU/RAM

Add / Edit

Details



1) Reflow the GPU/RAM- For better results blow under the chips and flush them with alcohol if you can (clhdrums87)2) X-Clamp Fix


Description:This error is caused by a Cold Joint in the GPU/RAM area similiar to 0102 good results could be achieved with flushing alcohol under the chips, reflowing them and afterwards applying an X-Clamp Fix.

References:clhdrums87 @ http://forums.xbox-experts.com/viewtopic.php?f=8&t=1799http://forums.xbox-scene.com/lofiversion/index.php/t484726-250.html

Clicks: 3018

Add / Edit


Details for Error code E33/0201Cold solderjoint-> GPU/RAM

Add / Edit

Details




0102

Description:The error is very rare but it is somehow GPU/RAM related, two people could fix it with the Improved X-Clamp replacement, one had to remove his washers from the RAM in order to get it to work.Check the references for more information.

References:idpopehttp://forums.xbox-scene.com/lofiversion/index.php/t599217-600.html

Clicks: 2953

Add / Edit


Details for Error code E35/0203GPU related - resistors

Add / Edit

Details




No Related Errors available!Description:

code 0203 - instant rrod everytime. chip malfunction, not gettin a connection to the board (not an overheating problem but a bad contact problem) mine turned out to be broken prongs in a corner on the gpu, missin 3 of them. didnt see this til i was comparing with another board. i believe these are mini resistors on the bottom side of the chip due to mistreatment

References:http://forums.xbox-scene.com/index.php?showtopic=650698&st=0&p=4275573&#entry4275573

Clicks: 14800

Add / Edit


gammmmes on 2010-05-25 23:03:16 :

I solved this error by fixing a bad x clamp. coolent fins weren't makingcontact with the gpu. cleaned and added artic silver as always.

Details for Error code E40/0220(unknown) missing resistors GPU

Add / Edit

Details





This error is unknown but is assumed to be caused by missing resistors, probably on GPU.References:

http://forums.xbox-scene.com/lofiversion/index.php/t484726-450.htmlClicks: 3308

Add / Edit


Texastboneking on 2010-10-17 19:37:00 :

i have a motherboard with this issue. i heated up both the video gpu and thehana chip with a heat gun and it has been working since. not sure if its a true

fix but it has worked on mine

matrixone976 on 2010-03-01 04:59:00 :

i'd really like to know if anyone has solved this issue as i want to beable to use my system again.

Details for Error code E42/0222(unknown)GPU/CPU related?

Add / Edit

Details


Binary/Hex: 00101010 / 0x2A -> 42Known fixes:

1) X-Clamp replacement


Description:This error is unknown but someone managed to fix it using the X-Clamp replacement.

References:http://forums.xbox-scene.com/index.php?showtopic=595746&st=45

Clicks: 1959

Details for Error code E46/0232DVD Drive Failure

Add / Edit

Details


Binary/Hex: 00101110 / 0x2E -> 46Known fixes:

It cant happen anymore since of new update.(Unconfirmed)Related Errors:


"The CD Drive overheats. This error can be caused by the disconnecting of the CD Drive. This is usually not the case."(Unconfirmed)

References:zman989

Clicks: 2062

Add / Edit


Documents

Error Codes