Equivalent Material Grades

SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SPECIFICATION CONTENTS Section

1. Scope 2. Basis 3. Additional Requirements 4. Table 5. Table 1, Plates 6. Table 2, Pipes 7. Table 3, Tubes 8. Table 4, Forging 9. Table 5, Castings 10. Table 6, Bolts and Nuts 11. Table 7, Bars and Shapes 12 Table 8, Piping Fittings 13. Table 9, Nonferrous Materials

1. SCOPE This specification lists the Japanese Standard (JIS, JPI),British Standard (BS), and Deutshe Industrie Normen (DIN) substitutes for ASTM Specifications relating to materials for plates, pipes, tubes, forging, castings, bolts and nuts, bars and shapes, piping fittings, and nonferrous materials, in general use. 2. BASIS These substitutes are not necessarily identical to the ASTM Specifications, but are equal in terms of alloy content and have a nearly equal or higher ultimate tensile strength; exceptions to this are underlined. 3. ADDITIONAL REQUIREMENTS The requirements of the ASTM Specifications not covered by the substitute specifications are noted in the Tables, with footnotes given on Section 4. 4. TABLE Substitute materials are shown in the following Tables 1 to 9.

STANDARD SPECIFICATION

Table 1 PLATE

ASTM JIS BS DIN A-36 Structural Steel G 3101 SS400 4360 Gr 40A (1) 17100 St44-2 G 3105 SM400A 4360 Gr 438 (1) 17100 St44-3 A-131

Structural Steel for Ships Gr A G 3106 SM400A 4360-40B 17100 St44-3 Gr B G 3106 SM400B 4360-40B --- Gr CS G 3105 SM400CN 4360-40E --- Gr D G 3105 SM400C (2) 4360-40E --- Gr E G 3105 SM40OCN 4360-40E --- A-167

Stainless arid Heat-Resisting Chromium,-Nickel Steel Plate, Sheet, and Strip Type 302 G 4304 SUS302 (3) --- 17440/1 X10CrNiS189 Type 304 G 4304 SUS304 (3) 1449-304S31 17440/1 X5CrNi1810 1501-304S15 Type 304L G 4304 SUS304L (3) 1501-304S12 17440/1 X2CrNi1911 1449-304S11 Type 310S G 4304 SUS310S (3) 1501-310S24 --- 1449-310S24 --- Type 316 G 4304 SUS316 (3) 1501-316S16 17440/1 X5CrNiMo17122 1449-316S31 Type 316L G 4304 SUS316L (3) 1501-316S12 17440/1 X2CrNiMo17132 1449-316S11 Type 321 G 4304 SUS321 (3) 1501-321S12 17440/1 X6CrNiTi1810 1449-321S31 Type 347 G 4304 SUS347 (3) 1501-347S17 17440/1 X6CrNiNb1810 1449-347S31

Note (1): Specify mechanical properties, test and inspection in accordance with ASTM. Note (2): Plates over 1-3/8 Inches (35 m-n) in thickness shall be normalized. Note (3): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G 4307, respectively.


ASTM JIS BS DIN A-176 Stainless and Heat Resisting Chromium Steel Plate, Sheet, And Strip Type 403 G 4304 SUS403 (1) 14-09-403 S17 S2) --- 1501-403 S17 l2) --- Type 405 G 4304 SUS405 (1) 1449-405 S17 17440/1 X6CrAl13 1501-405 S17 --- Type 410 G 4304 SUS410 (1) 1449-410 S21 17440/1 X10Cr13 Type 4105 G 4304 SUS410S (1) --- 17440/1 X6Cr13 A-203

Pressure Vessel Plates, Alloy Steel, Nickel Gr A G 3127 SL2N255 --- --- Gr D G 3127 SL3N255 1501-503 --- Gr E G 3127 SL3N275 --- 17280 10Ni14 Gr F G 3127 SL3N440 --- --- A-204 Pressure Vessel Plates, Alloy Steel, Molybdenum Gr A G 3103 S64SOM --- SEL 16 Mo5 17155 15 Mo3 Gr B G 3103 SB48M --- SEL 16 Mo5 Gr C --- --- --- A-240

Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels Type 304 G 4304 SUS304 (1) 1501-304S15 17440/1 X5CrNi1810 Type 304H --- 1501-304S49 --- Type 304L G 4304 SUS304L (1) 1501-304S12 17440/1 X2CrNi1911 Type 316 G 4304 SUS316 (1) 1501-316S16 17440/1

X5CrNiMo17122 Type 316H --- 1501-316S49 --- Type 316L G 4304 SUS316L (1) 1501-316S12 17440/1

X2CrNiMo17132 Type 317 G 4304 SUS317 (1) Type 317L G 4304 SUS317L (1) --- 17440/1

X2CrHiMo18164

Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307,

respectively. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or

specify minimum tensile and yield strengths per ASTM.


ASTM JIS BS DIN Type 321 G 4304 SUS321 (1) 1501-321S12 17440/1 X6CrNiTi1810 Type 321H --- 1501-321S49 --- Type 347 G 4304 SUS347 (1) 1501-3-07S17 17440/1 X6CrNiNb1810 Type 347H --- 1501-347S49 --- Type 405 G 4304 SUS405 (1) 1501-405S17 17440/1 X6CrAl13 Type 410 G 4304 SUS410 (1) --- 17440/1 X10Cr13 Type 410S G 4304 SUS410S (1) --- 17440/1 X6Cr13 Type 430 G 4304 SUS430 (1) --- 17440/1 X6Cr17 A-263 Corrosion-Resisting Chromium Steel-Clad Plate, Sheet, and Strip G 3601 (2) --- 17440/1 A-264 Stainless Chromic-Nickel Steel- Clad Plate, Sheet, and Strip G 3601 (2) 3740 (2) 17440/1 A-265 Nickel and Nickel-Base Alloy-Clad Steel Plate G 3602 (2) --- 17743 NiCu30Fe A-283 Low and Intermediate Tensile Strength Carbon Steel Plates, Shapes, and Bars Gr A G 3101 SS330 4360 Gr 40A/B/C 17100 St33 Gr B G 3101 55330 4360 Gr 40A/B/C 17100 St33 Gr C G 3101 SS400 4360 Gr 40D 17100 St44-2 Gr D G 3101 SS400 4360 Gr 43A/B/C/D 17100 St44-2

Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307, respectively.

Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.


Note (1): Recognize lacer minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.

ASTM JIS BS DIN A-285 Pressure Vessel Plates, Carbon Steel, Low-and Intermediate-Tensile Strength Gr A & B --- 1501-151 Gr 360 17155 H I Gr C G 3103 S8410 1501-151 Gr 430 17155 H II A-299

Pressure Vessel Plates, Carbon Steel, Manganese Silicon G 3115 SPV355 --- 17102 StE355 A-302 Pressure Vessel Plates, Alloy Steel Manganese-Molybderalm and Manganese-Holybdenum- Nickel Gr A G 3119 SBV1A --- --- Gr B G 3119 SBV1B --- --- Gr C G 3119 SBV2 --- --- Gr D G 3119 SBV3 --- --- A-387

Pressure Vessel Plates, Alloy Steel Chromium-Molybdenum Gr 2 Class 1 G 4109 SCMV1 --- --- Gr 11 Class 1 G 4109 SCMV3 1501-621 --- Class 2 G 4109 SCMV3 1501-621 Gr 12 Class 1 G 4109 SCMV2 1501-620 17155 13CrMo44 Class 2 G 4109 SCMV2 1501-620 --- Gr 21 Class 1 G 4109 SCMV5 --- --- Gr 22 Class 1 G 4109 SCMV4 1501-622 Gr 515 17155 10CrMo910 Class 2 G 4109 SCMV4 1501-622 Gr 515 --- Gr 5 Class 1 G 4109 SCMV6 --- SEW590 12CrMo195 Class 2 G 4109 SCMV6 --- --- Gr 9 Class 1 --- --- --- Class 2 --- --- ---

ASTM JIS BS DIN A-442 Pressure Vessel Plates, Carbon Steel, Improved Transition Properties Gr 55 --- 1501-151 Gr 400 SEW 680 TTSt41N 1501-161 Gr 400 1501-224 Gr 400 Gr 60 G 3115 SPV235 1501-151 Gr 430 --- 1501-161 Gr 430 1501-224 Gr 430 A-516 - Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Service Gr 55 --- 1501-161 Gr 400 17155 H I 1501-224 Gr 400 Gr 60 G 3118 SGV410 1501-161 Gr 430 17155 H II 1501-224 Gr 430 Gr 65 G 3118 SGV450 1501-224 Gr 460 17155 17Mn4 Gr 70 G 3118 SGV480 1501-224 Gr 490 17155 19Mn6

STANDARD SPECIFICATION Note (1): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and

yield strengths per ASTM. Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.

ASTM JIS BS DIN A-533 I Pressure Vessel Plates,Alloy Steel Quenched and Tempered Manganese- Molybdenum and Manganese- Molybdenum Nickel Type A Class 1 G 3120 SQV1A --- --- Class 2 G 3120 SQV1B --- --- Type B Class 1 G 3120 SQV2A --- --- Class 2 G 3120 SQV2B --- --- Type C Class 1 G 3120 SQV3A --- --- Class 2 G 3120 SQV3B --- --- A-537

Pressure Vessel Plates, Heat- Treated, Carbon-Manganese- Silicon Steel Class 1 G 3115 SPV355N 1501-224 Gr 490 (1) 17155 19Mn6 17102 StE355 Class 2 G 3115 SPV450Q --- --- A-570

Steel, Sheet and Strip, Carbon, Hot-Rolled, Structural Quality. Gr 30 G 3101 SS330 1449-HR 34/20 (1) 17100 St33 Gr 33 G 3101 SS400 1449-HR 37/23 17100 St44-2 Gr 36 G 3101 SS400 1449-KR 37/23 17100 St44-2 Gr 40 G 3101 SS400(1) 1449-HR 43/25 17100 St44-2 Gr 45 G 3101 SS490 1449-HR 43/25 (1) 17100 St52-3 Gr 50 G 3101 SS490(1) 1449-HR 50/35 17100 St52-3 A-611

Steel, Sheet, Carbon, Cold-Rolled Structural Quality Gr B G 3141 SPCC (2) --- --- Gr C G 3141 SPCC (2) --- 1623.1 St12 Gr D G 3141 SPCC (2) --- ---

STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. Note (2): Recognize lager minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and

yield strengths per ASTM.

ASTM JIS BS DIN A-652 Pressure Vessel Plates, Carbon Manganese, for Moderate and Lower Temperature Service Gr A G 3126 SLA235 (1) --- --- Gr B G 3126 SLA325 (1)(2) --- 17102 EStE315 Gr C G 3126 SLA360 (1) --- 17102 EStE355

STANDARD SPECIFICATION Table 2 PIPE Note (1): Specify carbon, manganese, or silicon contents to accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and


ASTM JIS BS DIN A-53 Pipe, Steel, Black and Hot-Dipped Zinc-Coated Welded and Seamless Type F G 3452 SGP 1387 1615 St33 Gr A G 3454 STPG370 3601 ERW360 1626 St37.0 S360 1629 St37.0 Gr B G 3454 STPG410 3601 ERW410 1626 St44.0 S410 1629 St44.0 A-106

Seamless Carbon Steel Pipe for High-Temperature Service Gr A G 3456 STPT370 3602 HFS360 17175 St35.8 3602 CFS360 Gr B G 3.455 STPT410 3602 HFS410 17175 St45.8 3602 CFS410 Gr C G 3456 STPT480 3602 HFS460 17175 St45.8 3602 CFS460 A-134 Pipe, Steel, Electric-Fusion (Arc)- Welded (Size NPS 16 and over) Material A 283 Gr A – D G 3457 STPY400 3602 SAW410 --- 3601 SAW410 A 285 Gr A – C G 3457 STPY400(1) --- -- A 570 Gr 30 – 40 G 3457 STPY400 (1)(2) --- -- A 36 G 3457 STPY400 3602 SAW410 -- 3601 SAW410

STANDARD SPECIFICATION Note (1): Specify electric resistance-welding. Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum

tensile and yield strengths per ASTM. Note (3): Specify carbon, manganese, or silicon contents in accordance with ASTM.

ASTM JIS BS DIN A-135 Electric-Resistance-Welded Steel Pipe Gr A G 3454 STPG370 (1) 3601 ERW360 1626 St37.0 Gr B G 3454 STPG410 (1) 3601 ERW410 1626 St44.0 . A-139

Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and over) Gr A – E G 3457 STPY400 (2)(3) 3602 SAW410 (2) --- 3601 SAW410 (2) A-211 Spiral-Welded Steel or Iron Pipe A 570 Gr 30-45 G 357 STPY400 (2)(3) 3602 SAW 410 (2) --- 3601 SAW 410 (2) A 570 Gr 50 --- 3502 SAW 460 (2) A-312

Seamless and Welded Austenitic Stainless Steel Pipe TP 304 (18Cr-8Ni) G 3459 SUS304TP 3605-304S18,S25 17457/58 X5CrNi1810 TP 304H (18Cr-8Ni) G 3459 SUS304HTP 3605-304S59 --- TP 304L (18Cr-8Ni) G 3459 SUS304LTP 3605-304S14,S22 17457/58 X2CrNi1911 TP 309 (23Cr-12Ni) G 3459 SUS309STP --- --- TP 310 (25Cr-20Ni) G 3459 SUS310STP --- --- TP 316 (16Cr-12Ni-21Mo) G 3459 SUS316TP 3605-316S18,S26 17457/58

X5CrNiMo17122 TP 316H (16Cr-12Ni-2Mo) G 3459 SUS316HTP 3605-316S59 17459E X6CrNiMo1713 TP 316L (16Cr-12Ni-2Mo) G 3459 SUS316LTP 3605-316S14,S22 17457/58

X2CrNiMo17132 TP 321 (18Cr-10Ni-Ti) G 3459 SUS321TP 3605-321S18,S22 17457/58 X6CrNiTi1810 TP 321H (l8Cr-12Ni-Ti) G 3459 SUS321HTP 3605-321S59 SEW470 X12CrNiTi189 TP 347 (18Cr-10Ni-Cb) G 3459 SUS347TP 3605-347S18,S17 17457/58

X6CrNiNb1810 TP 347H (18Cr-10Ni-Cb) G 3459 SUS347H TP 3605-347S59 ---

STANDARD SPECIFICATION Note (1):Recognize Lower minimum tensile or yield strengths of the underlined substitute materials in design consideration or specify minimum tensile and

yield strengths per ASTM. Note (2):VdTuv-Werkstoftblatt

ASTM JIS BS DIN A-333 Seamless and Welded Steel Pipe for Low-Temperature Service Gr 1 G 3460 STPL380 3603-CFS410 LT50 17173 TTSt35N 3603-HFS410 LT50 17174 TTSt35N 3603-ERW410 LT50 3603-CEW410 LT50 Gr 3 (3-1/2Ni) G 3460 STPL450 3603-HFS503 LT100 17173 l0Ni14 3603-CFS503 LT100 Gr 6 --- 3603-CFS410 LT50 SEW680 TTSt45N 3603-HFS410 LT50 3603-ERW410 LT50 3603-CEW410 LT50 Gr 8 (9Ni) G 3460 STPL690 3603-HFS509 LT196 17173 X8Ni9 3603-CFS509 LT196 A-335

Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service Gr P1 (C-1/2Mo) G 3458 STPA12 --- 17175 15Mo5 Gr P5 (5Cr-1/2Mo) G 3458 STPA25 3604 CFS625 (1) Wbl 007/2 12CrMo195

(2) 3604 HFS625 (1) Gr P9 (9Cr-1Mo) G 3458 STPA26 3604-CFS629-470 (1) Wbl 109 X12CrMo91 (2) Gr P11 (1-1/4Cr-1/2Mo) G 3458 STPA23 3604 CF5621 17175 13CrMo44 3604 HFS621 Gr P12 (1Cr-1/2Mo) G 3458 STPA22 3604 CFS620-460 (1) 17175 13CrMo44 3604 HFS620-460 (1) Gr P22 (2-1/4Cr-1Mo) G 3458 STPA24 3604 CFS622 17175 l0CrMo910 3604 HFS622

STANDARD SPECIFICATION Note (1): Specify seamless.

ASTM JIS BS DIN A-358 Electric-Fusion-welded Austenitic Chromium-Nickel Alloy Steel Pipe For High-Temperature Service Grade Material

304 A240, Type 304 G 3468 SUS304TPY 3605 LWHT 304S18 17457 X5CrNi1810 304L A240, Type 304L G 3468 SUS304LTPY 3605 LWHT 304S14 17457 X2CrNi1911 316 A240, Type 316 G 3468 SUS316TPY 3505 LWHT 316S18 17457 X5CrNiMo17122 316L A240, Type 316L G 3468 SUS316LTPY 3605 LWHT 316S14 17457 X2CrNiMo17132 321 A240, Type 321 G 3468 SUS321TPY 3605 LWHT 321S18 17457 X6CrNiTi1810 347 A240, Type 347 G 3468 SUS347TPY 3605 LWHT 347S18 17457 X6CrNiNb1810 A-376

Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service TP 304 (18Cr-8Ni) G 3459 SUS304TP (1) 3605-304S18 17459

E X6CrNi1811

TP 304H (18Cr-8Ni) G 3459 SUS304HTP (1) 3605-304S59 --- TP 316 (16Cr-12Ni-2Mo) G 3459 SUS316TP (1) 3605-316S18 17458 X5CrNiMo17122 TP 316H (16Cr-12Ni-2Mo) G 3459 SUS316HTP (1) 3605-316S59 17459

E X6CrNiMo1713

TP 321 (18Cr-10Ni-Ti) G 3459 SUS321TP (1) 3605-321S18 17458 X6CrNiTi810 TP 321H (18Cr-10Ni-Ti) G 3459 SUS321HTP (1) 3605-321S59 --- TP 347 (18Cr-10Ni-Cb) G 3459 SUS347TP (1) 3605-347S18 17458 X6CrNiNb1810 TP 347H (18Cr-10Ni-Cb) G 3459 SUS347HTP (1) 3605-347S59 --- A-409 Welded Large Diameter Austenitic

Steel Pipe for Corrosive or High Temperature Service TP 304 (18Cr-8Ni) G 3468 SUS304TPY --- 17457 X5CrNi810 TP 304L G 3463 SUS304LTPY --- 17457 X2CrNi1911 TP 316 (16Cr-12Ni-2Mo) G 3468 SUS316TPY --- 17457 X5CrNiMo17122 TP 316L G 3468 SUS316LTPY --- 17457 X2CrNiMo17132 TP 321 (18Cr-10Ni-Ti) G 3468 SUS321TPY --- 17457 X6CrNiTi1810 TP 347 (18Cr-10Ni-Cb) G 3468 SUS347TPY --- 17457 X6CrN iNb1810

STANDARD SPECIFICATION Note (i): Specify electric resistance-welding. Note (2): Maximum carbon content shall be 0.15%. Note (3): Specify Impact Test requirement per ASTM.

ASTM JIS/JPI BS DIN A-524 Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures Gr 1 --- --- SEW680 TTSt41 Gr 11 --- A-587

Electric-Welded Low-Carbon Steel Pipe for the Chemical Industry G 3454 STPG370 (1)(2) --- 1626 St37.0 A-671

Electric-Fusion-Welded Steel pipe for Atmospheric and Lower Temperatures Grade Material

CA55 A285 Gr C CB60 A515 Gr 60 JPI-SB42 --- --- CB70 A515 Gr 65 JPI-SB46 --- --- CB70 A515 Gr 70 JPI-SB49 --- --- CC60 A516 Gr 60 JPI-SLA24B (3) --- --- CC65 A516 Gr 65 JPI-SLA33B (3) --- --- CD70 A537 CL 1 --- --- --- CE55 A442 Gr 55 --- --- --- CE60 A442 Gr 60 JPI-SPV24 --- --- CF70 A203 Gr B --- --- --- CF71 A203 Gr E JPI-SL3N28 --- --- CK75 A299

STANDARD SPECIFICATION Note (1): Specify Impact Test requirement per ASTM. Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and


ASTM JIS/JPI BS DIN A-672 Electric-Fusion-Welded Steel Pipe for High- Pressure Service at Moderate Temperature Grade Material

A55 A285 Gr C JPI-SB42 --- --- B55 A515 Gr 55 --- --- --- B60 A515 Gr 60 JPI-SB42 --- --- B65 A515 Gr 65 JPI-SB46 --- --- B70 A515 Gr 70 JPI-SB49 --- --- C55 A516 Gr 55 --- --- --- C60 A516 Gr 60 JPI-SLA24B (1) --- --- C65 A516 Gr 65 JPI-SLA33B (1) --- --- C70 A516 Gr 70 --- --- --- D70 A537 CL 1 --- --- --- E55 A442 Gr 55 --- --- --- E60 A442 Gr 60 JPI-SPV24 --- --- L65 A204 Gr A JPI-SB46M --- --- L70 A204 Gr B JPI-SB49M (2) L75 A204 Gr C --- --- --- N75 A299 --- --- ---


ASTM/API JIS/JPI BS DIN A-691 Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High- Pressure Service at High Temperatures Grade Material CM-65 A204 Gr A JPI-SB46M --- --- CM-70 A204 Gr B JPI-SB49M --- --- CM-75 A204 Gr C --- --- --- CMSH-70 A537 CL 1 --- --- --- CMS-75 A299 --- --- _-- ½ Cr A337 Gr 2 CL 1 --- --- --- 1 Cr A387 Gr 12 CL 1 JPI-SCMV2 --- --- 1-1/4 Cr A387 Gr 11 CL1 JPI-SCMV3 --- --- 2-1/4 Cr A387 Gr 22 CL1 JPI-SCMV4 --- --- 5 Cr A387 Gr 5 CL 1 JPI-SCMV6 --- --- API 5L Line Pipe Gr A25 63452 SGP 1387 --- Gr A 63454 STPG370 3601 ERW 360 17172 StE210.7 3601 S 360 Gr B 63454 STPG410 3601 ERW 430 (1) 17172 StE240.7 3601 S 430 (1) 3601 SAW 430 (1) 6327 Part 1-8 (1) Gr X42 --- --- 17172 StE290.7 Gr X46 --- --- 17172 StE320.7 Gr X52 --- --- 17172 StE360.7 Gr X56 --- --- 17172 StE385.7 Gr X60 --- --- 17172 StE415.7 Gr X65 --- --- 17172 StE445.7TM Gr X70 --- --- 17172 StE480.7TM --- 63455 STS370 --- 1630 St37.4 --- 63455 STS410 --- 1630 St44.4 --- 63455 STS480 --- 1630 St52.4

Note (1): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or

Table 3 TUBES

ASTM JIS BS DIN A-161 Seamless Low-Carbon and Carbon Molybdenum Steel Still Tubes for Refinery Service Low Carbon Steel G 3461 ST340 (1) (2) 3059 HFS320 (2) 17175 St35.8 3059 CFS320 (2) Gr T1 G 3462 STBA12 (1)(2)(3) --- 17175 15Mo5 G 3467 STFA12 (2) A-178

Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler Tubes Gr A G 3461 STB340 (40 3059 ERW320 (3) 17177 St37.8 3059 CEW320 (3) Gr C G 3461 STB410 (4) 3059 ERW360 17177 St42.8 3059 CEW360 (3) Gr D --- 3059 ERW440 (3) --- 3059 CEW440 (3) A-179

Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes G 3461 STB340 (1)(5)(6) 3606 CFS 320 17175 St35.8 3059 S1 360 (5)(6)

Note (1): Specify seamless. Note (2): Maximum hardness shall be as follows:

Item Carbon Steel Hot rolled tubes Cold drawn tubes

HB 137 HB 125

Note (3): Specify killed steel. Note (4): Specify electric resistance-welding. Note (5): Specify cold drawn. Note (6): Maximum hardness shall be Rockwell B72.


ASTM JIS BS DIN A-192 Seamless Carbon Steel Boiler Tubes for High- Pressure Service G 3-061 STB340 (1)(2) 3059 HFS 320 (2) 17175 St35.8 3059 CFS 320 (2) 3059 S1 360 (2) 3059 S2 360 (2) A-199

Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchenger and Condenser Tubes Gr T5 G 3462 STBA25 (3)(4) 3606 CFS 625 Wbl 007/2 12CrMio195 (6)Gr T9 G 3462 STBA26 (3)(5) 3059 S1 629-470 (3)(5) Wbl 109 X12CrMo91 (6) 3059 S2 629-470 (3)(5) Gr T11 G 3462 STBA23 (3)(4) 3606 CFS621 17175 13CrMo44 Gr T22 G 3462 STBA24 (3)(4) 3606 CFS622 17175 10CrMo910 3059 S1 622-440 (3)(4) 3059 S2 622-440 (3)(4) A-200

Seamless Intermediate Alloy-Steel Still Tubs for Refinery Service Gr T5 G 3462 STBA25 (4) 3604 CFS625 (4) Wbl 007/2 12CrMo195 (6) G 3467 STFA25 (4) 3604 HFS625 (4) Gr T7 --- --- --- Gr T9 G 3462 STBA26 (5) 3604 CFS629-470 (5) Wbl 109 X12CrMo91 (6) G 3467 STFA26 (5) 3604 HFS629-470 (5) 3059 S1 629-470 (5) 3059 S2 629-470 (5) Gr T11 G 3462 STBA23 (4) 3604 CFS621 (4) 17175 13CrMo44 G 3467 STFA23 (4) 3604 HES621 (4) Gr T22 G 3462 STBA24 (4) 3059 S1 622-440 (4) 17175 10CrMo910 G 3467 STFA24 (4) 3604 CFS622 (4) 3604 HFS622 (4)

Note (1): Specify seamless. Note (2): Maximum hardness shall be Rockwell 677.

Note (3): Specify cold drawn.

Note (4): Maximum hardness shall be Rockwell 885.

Note (5): Maximum hardness shall be Rockwell B89.

Note (6): VdTuv-Herkstoftblatt


ASTM JIS BS DIN A-209 Seamless Carbon-Molybdenum Alloy-Steel Boiler and Super Heater Tubes Gr T1 G 3462 STBA12 (1)(2) 3059 S1 243 (2) 17175 15Mo5 3059 S2 243 (2) --- Gr Tla G 3462 STBA13 (1)(3) 3059 S1 243 (3) 17175 15Mo5 3059 S2 243 (3) ~ Gr Tlb --- --- --- A-210

Seamless Medium-Carbon Steel Boiler and Super heater Tubes Gr A1 G 3461 STB410 (1)(4) 3059 S1 440 17175 St45.8 S2 440 (4) A-213

Seamless Ferritic and Austenitic Alloy-Steel Boiler, Super heater and Heat-Exchanger Tubes Gr T 5 G 3462 STBA25 (5) 3606 CFS 625 Wbl 007/2 12CrMo195

(7) Gr T 11 G 3462 STBA23 (5) 3606 CFS 621 17175 13CrMo44 Gr T 12 G 3462 STBA22 (1)(5) 3506 CFS 620 17175 13CrMo44 3059 S1/S2 620 (5) Gr T 22 G 3462 STBA24 (5) 3606 CFS 622 17175 10CrMo910 3059 S1/S2622-

440/490(5)

Gr TP 304 G 3463 SUS304 TB (1)(6) 3606 CFS 304S25 17458 X5CrNi1810 Gr TP 3D4H G 3463 SUS304H T8 (1)(6) 3059 CFS304S59 (6) --- Gr TP 304L G 3463 SUS304L TB (1)(6) 3606 CFS304S22 17458 X2CrNi1911 Gr TP 310 G 3463 SUS310S TB (1)(6) --- --- Gr TP 316 G 3463 SUS316 TB (1)(6) 3606 CFS316S25 17458 X5CrNiMo17122 Gr TP 316H G 3463 SUS316H TB(1)(6) 3059 CFS316S59 (6) 17459E X6CrNiMo1713 Gr TP 316L G 3463 SUS316L TB (1)(6) 3606 CFS316S29 17458 X2CrNiMo17132 Gr TP 321 G 3463 SUS321 TB (1)(6) 3606 CF5321S22 17458 X6CrNiTi1810 Gr TP 321H G 3463 SUS321H TB(1)(6) 3059 CFS321S59 (6) --- Gr TP 347 G 3463 SUS347 TB (1)(6) 3606 CFS347S17 17458 X6CrNiNb1810 Gr TP 347H G 3463 SUS347H TB(1)(6) 3059 CFS347S59 (6) ---

Note (1): Specify seamless. Note (2): Maximum hardness shall be Rockwell B90. Note (3): Maximum hardness shall be Rockwell B81. Note (4): Maximum hardness shall be Rockwell B79. Note (5): Maximum hardness shall be Rockwell B85. Note (6): Maximum hardness shall be Rockwell B90. Note (7): VdTuv-Werkstoftblatt


ASTM JIS BS DIN A-214 Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes G 3461 STB340 (1)(2) 3606 ERW 320 17177 St37.8 3059 ERW 320 (2) 3059 CEW 320 (2) 3059 ERW 360 (2) 3059 CEW 360 (2) A-226

Electric-Resistance-Welded Carbon Steal Boiler and Superheater Tubes for High-Pressure Service G 3461 STB340 (1)(2) 3059 ERW320 (2) 17177 St37.8 3059 CEW320 (2) 3059 ERW360 (2) 3059 CEW360 (2) A-249

Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condense; Tubes TP 304 G 3463 SUS304 TB (3) --- 17457 X5CrNi1810 TP 304H G 3463 SUS304H TB (3) 3059-ERW304S59 (3) --- TP 304L G 3463 SUS304L TB (3) --- 17457 X2CrNi1911 TP 309 G 3463 SUS309S TB (3) --- --- TP 310 G 3463 SUS310S TB (3) --- --- TP 316 G 3463 SUS316 TB (3) --- 17457 X5CrNiMo17122 TP 316H G 3463 SUS316H TB (3) 3059-ERW316S59 (3) TP 316L G 3463 SUS316L TB (3) --- 17457 X2CrNiMo17132 TP 321 G 3463 SUS321 TB (3) --- 17457 X6CrNiTi1810 TP 321H G 3463 SUS321H TB (3) 3059 ERW321S59 (3) --- TP 347 G 3463 SUS347 TB (3) --- 17457 X6CrNiNb1810 TP 347H G 3463 SUS347H TB (3) 3059-ERW347S59 (3) ---

Note (1): Specify electric resistance-welding. Note (2): Maximum hardness shall be Rockwell B72. Note (3): Maximum hardness shall be Rockwell B90.


ASTM JIS BS DIN A-268 Seamless and Welded Ferritic Stainless Steel Tubing for General Service TP 410 G 3463 SUS410 TB (1) --- --- TP 430 G 3463 SUS430 TB (2) --- --- A-269

Seamless and Welded Austenitic Stainless Steel Tubing for General Service TP 304 G 3463 SUS304 TB (2) 3605-304S18,S25 (2) --- TP 304L G 3463 SUS304L TB (2) 3605-304S14,S22 (2) --- TP 316 G 3463 SUS316 TB (2) 3605-316S18,S26 (2) --- TP 316L G 3463 SUS316L TB (2) 3605-316S14,S22 (2) --- TP 321 G 3463 SUS321 TB (2) 3605-321S18,S22 (2) --- TP 347 G 3463 SUS347 TB (2) 3605-347S18,S17 (2) --- A-271

Seamless Austenitic Chromium Nickel Steal Still Tubes for Refinery Service TP 304 G 3463 SUS304 TB (2)(3) 3605-304S18 (2) 17459E X6CrNi1811 G 3467 SUS304 TF (2) TP 304H G 3463 SUS304H TB (2)(3) 3605-304S59 (2) --- G 3467 SUS304H TF (2) 3059-CFS304S59 (2) TP 316 G 3463 SUS316 TB (2)(3) 3605-316S18 (4) 17458 X5CrNiMo17122 G 3467 SUS316 TF (2) TP 316H G 3463 SUS316 HTB (2)(3) 3605-316S59 (4) 17459E X6rNiMo1713 G 3467 SUS316 HTF (2) 3059-316S59 (4) TP 321 G 3463 SUS321 TB (2)(3) 3605-321S18 (2) 17458 X6CrNiTi1810 G 3467 SUS321 TF (2) TP 321H G 3463 SUS32114 TB (2)(3) 3605-321S59 Gr 1010

(2) ---

G 3467 SUS321H TF (2) 3059-CFS321S59 Gr 1010(2)

TP 347 G 3463 SUS347 TB (2)(3) 3605-347S18 (2) 17458 X6CrNiNb1810 G 3467 SUS347 TF (2) TP 347H G 3463 SUS347H TB (2)(3) 3605-347S59 (2) --- G 3467 SUS347H TF (2) 3059-CFS347S59 (2) ---

Note (1): Maximum hardness shall be Rockwell B95. Note (2): Maximum hardness shall be Rockwell B90. Note (3): Specify seamless. Note (4): Maximum carbon content shall be 0.21%


ASTM JIS BS DIN A334 Seamless and Welded Carbon And Alloy-Steel Tubes for Low-Temperature Service Gr 1 G 3464 STBL380 (1) 3603 CEW410 LT50 (1) 17173 T7St35N 3603 CFS410 LT50 (1) 17174 TTSt35N 3603 ERW410 LT50 (1) 3603 HFS410 LT50 (1) Gr 3 G 3464 STBL450 (2) 3603 CFS503 LT100 (2) 17173 10Ni14 3603 HFS503 LT100 (2) Gr 6 --- 3603 CEW410 LT50 (2) SEW680 TTSt45N 3603 CFS410 LT50 (2) 3603 ERW410 LT50 (2) 3603 HFS4110 LT50 (2) Gr 8 G 3464 STBL690 (2) 3603 CFS509 LT196

(2) 17173 X8Ni9

3603 HFS509 LT196 (2)

Note (1): Maximum hardness shall be Rockwell B85. Note (2): Maximum hardness shall be Rockwell B90.


Table 4 FORGINGS

ASTM JIS BS DIN A-105 Forging, Carbon Steel, For Piping Components G 3202 SFVC2A 1503-221-490 --- A-181

Forging, Carbon Steel, for General - Purpose Piping Class 60 G 3202 SFVC1 1503-221-430 17200 C22N Class 70 G 3202 SFVC2A 1503-221-490 --- A-182

Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High –Temperature Service F1 (C-1/2Mo) G 3203 SFVAF1 1503-245-420 (1) VdTuv201 16Mo5 FS (5Cr-1/2Mo) G 3203 SFAF58 1503-625-520 VdTuv1207 12CrMo195 F9 (9Cr-1Mo) G 3203 SFVAF9 --- W.St.Nr17386

X12CrMo910 F11 (1-1/4Cr-I/2Mo) G 3203 SFVAF11A 1503-621-460 SEW550 16CrMo44 F12 (1Cr-1/2Mo) G 3203 SFVAF12 1503-620-540 SEW550 13CrMo44 F21 (3Cr-1Mo) G 3203 SFVAF21B --- --- F22 (2-1/4Cr-1Mo) G 3203 SFVAF22B 1503-622-560 SEW550 10CrMo9I0 F304 (18Cr-8Ni) G 3214 SUS304 1503-304S31 17440 X5CrNi1810 F304H (18Cr-8Ni) G 3214 SUS304H 1503-304S51 --- F304L (18Cr-8Ni) G 3214 SUSF304L 1503-304S11 17440 X2CrNi1911 F316 (16Cr-12Ni-2Mo) G 3214 SUSF316 1503-316S31 or 33 17440 X5CrNiMo17122 F316H (16Cr-12Ni-2Mo) G 3214 SUSF316H 1503-316S51 --- F316L (16Cr-12Ni-2Mo) G 3214 SUS316L 1503-316S11 or 13 17440 X2CrNiMo17132 F321 (18Cr-10Ni-Ti) G 3214 SUS321 1503-321S31 17440 X6CrNiTi1810 F321H (18Cr-10Ni-Ti) G 3214 SUSF321H 1503-321S51-510 --- F347 (18Cr-10Ni-Cb) G 3214 SUSF347 1503-347S31 17440 X6CrNiNb1810 F347H (18Cr-10Ni-Cb) G 3214 SUSF347H 1503-347S51 ---

Note (1): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or


ASTM JIS BS DIN A-226 Forging, Carbon Steel, for Pressure Vessel Component Class 1 G 3202 SFVC1 1503-221-430 17200 C22N Class 2 G 3202 SFVC2A 1503-221-490 --- Class 4 G 3202 SFVC2B A-336

Steel Forging, Alloy, for Pressure Refer to A-182 Refer to A-182 Refer to A-182 and High- Temperature Parts A-350

Forging, Carbon and Low-Alloy Steel, Requiring Notch Toughness Testing for Piping Component LF1 G 3205 SFL1 1503-221-430 (1) SEW680 TTSt41 LF2 G 3205 SFL2 1640 WPLO SEW680 TTStE36 1503-221-490 (1) LF3 (3-1/2Ni) G 3205 SFL3 1640 WPL3 17280 10Ni14 1503-503-490 (1) A-508

Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forging for Pressure Vessel Class 1 G 3202 SFVC2B --- --- Class 2 G 3204 SFVQ2A --- SEW640 22NiMoCr37 Class 3 G 3204 SFVQ1A --- SEW640 20MrMoNi55 A-541

Steel Forging, Carbon and Alloy Quenched and Tempered, for Pressure Vessel Component Class 1 G 3202 SFVC2B 1503-221-490 (1)(2) --- Class 2 G 3204 SFVQ2A --- --- Class 3 G 3204 SFVQ1A --- ---

Note (1): Specify Impact Test requirement per ASTM. Note (2): Specify heat treatment and mechanical properties per ASTM.

STANDARD SPECIFICATION Table 5 CASTINGS

ASTM JIS BS DIN A-27 Steel Castings, Carbon, for General Application Gr 60-30 G 5101 SC410 (1) 3100 Steel A1 1681 GS-38 (2) Gr 65-35 G 5101 SC450 (1) --- 1681 GS-45 Gr 70-36 G 5101 SC480 (1) 3100 Steel A2 1681 GS-52 A-47

Ferrltic Malleable Iron Castings Gr 32510 G 5702 FCM3340 6681 B35-12 1692 GTS-35-10 Gr 35018 G 5702 FCM3360 --- 1692 GTS-35-10 (2) A-48

Gray Iron Castings Class 20 G 5501 FC150 1452 Gr 150 1691 GG-15 Class 25 G 5501 FC200 1452 Gr 180 1691 GG-20 Class 30 G 5501 FC200 (2) 1452 Gr 220 1691 GG-20 (2) Class 35 G 5501 F 250 1452 Gr 260 1691 GG-25 Class 40 G 5501 FC300 1452 Gr 300 1691 GG-30 Class 45 G 5501 FC300 (2) 1452 Gr 300 (2) 1691 GG-30 (2) Class 50 G 5501 FC350 1452 Gr 350 1691 GG-35 Class 55 --- 1452 Gr 400 --- Class 60 --- --- A-126

Gray Iron Castings for Valves Flanges and Pipe Fittings Class A G 5501 FC200 1452 Gr 180 1691 GG-15 Class 6 G 5501 FC250 1452 Gr 260 1691 GG-25 Class C G 5501 FC300 1452 Gr 300 1691 GG-30

Note (1): Specify carbon, manganese, or silicon contents in accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum

tensile and yield strengths per ASTM.


ASTM JIS BS DIN A-216 Steel Castings, Carbon, Suitable for Fusion Welding, For High-Temperature Service WCA G 5151 SCPH1 (1) 1504-161 Gr 430 17245 GS-C25 WCB G 5151 SCPH2 (1) 1504-161 Gr 480 17245 GS-C25 WCC --- 1504-161 Gr 540 (2)(3) --- A-217

Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service WC1 (C-1/2Mo) G 5151 SCPH11 (1) 1504-245 17245 GS-22Mo4 WC6 (1-1/4Cr-1/2Mo) G 5151 SCPH21 (1) 1504-621 17245 GG-17CrMo55 WC9 (2-1/4Cr-1Mo) G 5151 SCPH32 (1) 1504-622 17245 CS-19CrMo910 C5 (Cr-1/2Ho) G 5151 SCPH61 (1) 1504-625 SEW 595 GS-2CrMo195 C12 (9Cr-1Mo) --- 1504-629 SEW 595 GS-2CrMo101 A-297

Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application Gr HC G 5122 SCH2 --- --- Gr HD G 5122 SCH11 --- --- Gr HE G 5122 SCH17 3100-309C40 --- Gr HF G 5122 SCH12 3100-302C35 --- Gr HH G 5122 SCH13 3100-309C30 --- Gr HI G 5122 SCH18 --- --- Gr HK G 5122 SCH22 or 21 3100-310C40 --- Gr HN G 5122 SCH19 3100-311C11 --- Gr HT G 5122 SCH15 3100-330C12 --- Gr HU G 5122 SCH20 3100-331C60 ---

Note (1):Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the steel.

Note (2): Specify carbon, manganese, or silicon contents in accordance with ASTM. Note (3): Specify elongation in accordance with ASTM.


ASTM JIS BS DIN A-338 Malleable Iron Flanges, Pipe Fittings, and Valve Parts for Railroad, Marine, and Other Heavy Duty Service at Temperatures up to 650°F (345°C) A-351

Steel Castings, Austenitic, for High-Temperature Service Gr CF3 (18Cr-8Ni) G 5121 SCS19A (1) 1504-304C12 (2) --- 3100-304C12 (2) Gr CF3A (18Cr-8Ni) --- --- --- Gr CF3M (17Cr-10Ni-2Mo) G 5121 SCS16A (1) 1504-316C12 (2) --- 3100-316C12 (2) Gr CF8 (18Cr-8Ni) G 5121 SCS13A (1) 1504-304C15 17445 G-X6CrNi189 3100-304C15 Gr CF8A (18Cr-8Ni) --- --- _-- Gr CF8C (20Cr-10Ni-Cb) G 5121 SCS21 (1) 1504-347C17 17445 G-X5CrNiNb189 3100-347C17 Gr CF8M (18Cr-10Ni-2Mo) G 5121 SCS14A (1) 1504-316C16 17445 G-X6CrNiMo1810 3100-316C16 Gr CH10 (25Cr-13Ni) G 5121 SCS17 (1)(2) --- --- Gr CH20 (25Cr-13Ni) G 5121 SCS17 (1)(3) 3100-309C30 --- Gr CK20 (25Cr-20Ni) G 5121 SCS18 (1) --- --- Gr CN7M (28Ni-20Cr- G 5121 SCS23 (1) 1504-332C11 --- 2Mo-3Cb) Gr HK40 (25Cr-20Ni) G 5122 SCH22 (1) 1504-310C40 --- 3100-310C40

Note (1): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel.

Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and yield strengths per ASTM.



ASTM JIS BS DIN A-352 Steel Castings, Ferritic and Martensitic, for Pressure- Containing Parts Suitable for Low-Temperature Service LCB G 5152 SCPL1 (1) 1504-161 Gr 480 LT40 SEW685 GS-CK24 LC1 (C-1/2Mo) G 5152 SCPL11 (1) 1504-245 LT50 --- 3100-BL1 LC2 (2-1/2Ni) G 5152 SCPL21 (1) --- --- LC3 (3-1/2Ni) G 5152 SCPL31 (1) 1504-503 LT60 SEW685 GS-10Ni14 3100-BL2 LC9 --- --- --- A-395

Ferritic Ductile Iron Pressure- Retaining Castings for Use at Elevated Temperatures 88243, APPENDIX-1 2789 Gr 420/12 (2) ---

FCD-S A-447

Steel Castings, Chromium-Nickel -Iron Alloy Castings (25-12 Class) for High-Temperature Service G 5122 SCH13 (3) 3100-309C32 --- A-494

Casting, Nickel and Nickel Alloy M-35-1 --- 3071-NAI --- M-30H --- 3071-NA2 (4) --- M-25S --- 3071-NA3 ---

Note (1): Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the steel.

Note (2): Specify ferritizing heat treatment, chemical requirement and mechanical properties, except for tensile and yield strengths. Note (3): Specify mechanical properties, test and inspection in accordance with ASTM Note (4): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify

minimum tensile and yield strengths per ASTM.


ASTM JIS BS DIN A-536 Ductile Iron Castings Gr 60-40-18 G 5502 FCD450 (1) 2789 Gr 420/12 --- Gr 65-45-12 G 5502 FCD500 (1) 2789 Gr 500/7 1693 GGG-50 Gr 80-55-06 G 5502 FCD600 (1) 2789 Gr 600/3 (2) 1693 GGG-60 Gr 100-70-03 G 5502 FCD700 (1) 2789 Gr 700/2 (2) 1693 GGG-70 A-743

Castings, Iron-Chromium, Iron-Chromium Nickel, Nickel Base, Corrosion Resistant, for General Application Gr CA-15 G 5121 SCS1 (3) 3100-410C21 (2) 17445 G-X20Cr14 Gr CA-40 G 5121 SCS2 (3) 1504-420C29 --- 3100-420C29 Gr CF-3 G 5121 SCS19A (3) 1504-344C12 --- 3100-304C12 Gr CF-3M G 5121 SCS16A (3) 1504-316C12 --- 3100-316C12 Gr CF-8 G 5121 SCS13A (3) 1504-304C15 17445 G-X6CrNi189 3100-304C15 Gr CF-8C G 5121 SCS21 (3) 1504-347C17 17445 G-X5CrNiNb189 Gr CF-8M G 5121 SCS14A (3) 1504-316C16 17445 G-X6CrNiMo1810 3100-316C16 Gr CF-20 G 5121 SCS12 (3) --- --- Gr CH-20 G 5121 SCS17 (3) 3100-309C30 --- Gr CK-20 G 5121 SCS18 (3) --- --- Gr CN-7M G 5121 SCS23 (3) 1504-332C11 ---

Note (1): Specify elongation in accordance with ASTM. Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify

minimum tensile and yield strengths per ASTM. Note (3): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the

steel.


Table 6 BOLTS AND NUTS

ASTM JIS BS DIN A-193 Alloy-Steel and Stainless Steel Bolting Materials for High Temperature Service Gr B5 (5Cr) G 4107 SNB5 --- --- Gr B6 (12Cr) G 4303 SUS410 1506-410S21-772 1654 X10Cr13 Gr B7 (Cr-Mo) G 4107 SNB7 1506-630-860 17200 42CrMo4 17240 24CrMo5 (3) Gr B7M (Cr-0.2Mo) G 4107 SNB7 (1) 1506-630-690 17200 42CrMo4 17240 24CrMo5 (3) Gr B8 G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810 CL 1 (304 sol.trt.) CL 4 (304 str.hd.) Gr B8C G 4303 SUS347 (2) 1506-347S31 17440 X6CrNiNb1810 CL 1 (347 sol.trt.) CL 2 (347 str.hd.) Gr B8M G 4303 SUS316 (2) 1506-316S31 17440 X5CrNiMo17122 CL 1 (316 sol.trt.) CL 2 (316 str.hd.) Gr B8T G 4303 SUS321 (2) 1506-321S31 17440 X6CrNiMTi1810 CL 1 (321 sol.trt.) CL 2 (321 str.hd.) Gr B16 (Cr - Mo - V) G 4107 SNB16 1506-670-860 17240 40CrMoV47 A-194

Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service Gr 2H G 4051 S45C (3) 1506-162 17240 C35 1654 Cq45 Gr 4 (C-Mo) -- --- 17240 24CrMo5 Gr 6 (12Cr) G 4303 SUS410 (3) 1506-410S21-770 1654 X10Cr13 Gr 8 (304) G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810 Gr 8MA (316) G 4303 Sus316 (2) 1506-316S31 17440 X5CrNiMo17122 A-307

Carbon Steel Externally Threaded Standard Fasteners Gr B G 3101 SS400 (4) 4190-Gr 4,6 17100 St44.2 17100 St44.3 G 4051 S25C (4) 17200 CK25 1654 Cq22

Note (1): Specify heat treatment and mechanical properties per ASTM.

Note (2): Specify ASTH dimensional requirements, tolerances and inspection.


Note (4):Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel.


ASTM JIS BS DIN A-320 Alloy Steel Bolting Materials for Low Temperature Service Gr L7 (Cr-Mo) G 4107 SNB7 (1) 1506-630-860 17200 42CrMo4 17240 24CrMo5 Gr L43 (Ni-Cr-Mo) G 4103 SNCM439 --- --- Gr B8 (304 str.hd.) G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810 Gr B8C (347 str.hd.) G 4303 SUS347 (2) 1506-347S31 17440 X6CrNiNb1810 970-347S31 Gr B8T (321 str.hd.) G 4303 SUS321 (2) 1506-321S31 17440 X6CrNiTi1810 970-321S31 Gr B8M (316 str.hd.) G 4303 SUS316 (2) 1506-316S31 17440 X5CrNiMo17I22 970-316S31 A-325

High-Strength Bolts for Structure Steel Joints G 4051 S33C 3139 1654 Cq35 A-354

Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners Gr BC --- --- -- Gr BD --- --- -- A-453

Bolting Materials, High-Temperature , 50 to 120 KSI (345 to 827 Mpa) Yield Strength, with Expansion Coefficients Comparable to Austenitic Steels Gr 660 Class A & B --- --- --- (14Cr-24Ni) Gr 651 Class A & B --- --- --- (19Cr-9Ni)

Note (1): Specify Impact Test requirement per ASTM. Note (2): Specify ASTM dimensional requirements, tolerances and inspection.

STANDARD SPECIFICATION Table 7 BARS AND SHAPES

ASTM JIS BS DIN A-276 Stainless and Heat-Resisting Steel Bars and Shapes Type 420 G4303 J1 970-420S37 17440 X20Cr13 A-576

Steel Bars, Carbon, Hot-Wrought Special Quality Gr 1020 G4051 S20C --- 17200 CK22 Gr 1025 G4051 S25C --- 17200 CK25 Gr 1030 G4051 S30C --- 17200 CK30 Gr 1035 G4051 S35C --- 17200 CK35 Gr 1040 G4051 S40C --- 17200 CK40 Gr 1045 G4051 S45C --- 17200 CK45 A-615

Deformed and Plain Billet-Steel Bars for Concrete Reinforcement Gr 40 G3112 SD295 Gr 250 (1) -- Gr 60 G3112 SD390 (1) Gr 460/425 (1) 488 BSt420S A-675

Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties Gr 45 G3101 SS330 Gr 40A (1) 17100 St33 Gr 50 G3101SS330 (1) Gr 40A (1) 17100 St33 Gr 55 G3101 SS400 Gr 40A (1) 17100 St44-2 17100 St44-3 Gr 60 G3101 SS400 (1) Gr 43A 17100 St44-2 17100 St44-3 Gr 65 G3101 SS490 Gr 50A (1) 17100 St52-3 Gr 70 G3101 SS490 Gr 55C or 50A (1) 17100 St52-3 Gr 75 G3101 SS540 Gr 55C or 50A (1) --- Gr 80 G3101 SS540 (1) Gr 55C (1) ---

Note (1): Recognize loser minimum tensile or yield strengths of the underlined substitute materials in design consideration, or


Table 8 PIPING FITTINGS

ASTM JIS BS DIN A-234 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and Elevated Temperatures WPB B 2312 PT410 1640 WPB --- 6 2313 PT410W WPC B 2312 PT480 --- --- B 2313 PT480W WP1 (C-1/2Mo) B 2312 PA12 1640 WP1 --- B 2313 PA12W WP5 (5Cr-1/2Mo) B 2312 PA25 1640 WP5 --- B 2313 PA25W WP9 (9Cr-1/2Mo) 8 2312 PA26 --- --- B 2313 PA-96W WP11 (1-1/4Cr-1/2Mo) B 2312 PA23 1640 WP11 --- B 2313 PA23W WP12 (1Cr-1/2Mo) B 2312 PA22 --- --- B 2313 PA22W WP22 (2-1/4Cr-1Mo) B 2312 PA24 1640 WP22 --- 8 2313 PA24W A-403

Wrought Austenitic Stainless Steel Piping Fittings WP 304 (18Cr-8Ni) B2312 SUS304 1640-WP304 --- B2313 SUS304W WP 304H(18Cr-8Ni) B2312 SUS304H --- --- WP 304L (18Cr-8Ni) B2312 SUS304L 1640-WP304L --- B2313 SUS304LW WP 316 (16Cr-12Ni-2Mo) B2312 SUS316 1640-WP316 --- B2313 SUS316W WP 316H (16Cr-12Ni-2Mo) B2312 SUS316H --- --- WP 316L (16Cr-12Ni-2Mo) B2312 SUS316L 1640-WP316L --- B2313 SUS316LW WP 321 (18Cr-10Ni-Ti) B2312 SUS321 1640-WP321 --- B2313 SUS321W WP 321H (18Cr-10Ni-Ti) B2312 SUS321H --- --- WP 347 (18Cr-10Ni-Cb) B2312 SUS347 1640-WP347 --- B2313 SUS347W WP 347H (18Cr-10Ni-Cb) B2312 SUS347H --- ---


JIS BS DIN A-420 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low Temperature Service WL3 (3-1/2Ni) B 2312 PL450 1640-WPL3 --- B 2313 PL450W WL6 B 2312 PL380 1640-WPL0 --- B 2313 PL38OW WL8 (9Ni) B 2312 PL690 --- ---


Table 9 NONFERROUS MATERIALS

ASTM JIS BS DIN PIPE B-42

Seamless Copper Pipe, Standards H3300 C1020 2871-C103 1787 OF-Cu Sizes B-43

Seamless Red Brass Pipe, H3300 C4430 --- 17671 CuZn15 Standard Sizes B-165

Nickel-Copper Alloy Seamless Pipe and Tube N04400 H4552 NCUT 3074 --- B-167

Nickel-Chromium-Iron Alloys Seamless Pipe and Tubes N06600 G4903 NCF600TP B-337

Seamless and Welded Titanium and Titanium Alloy pipe Gr 1 H4630 TTP28 --- 17850 Ti1 Gr 2 H4630 TTP35 --- 17850 Ti2 Gr 3 H4630 TTP49 --- 17850 Ti3 Gr 7 --- --- B-407

Nickel-Iron-Chromium. Alloy Seamless Pipe and Tube N08800 G4903 NCF 800TP --- --- N08810 G4903 HCF 800HTP --- --- G4903 NCF 825TP --- --- B-466

Seamless Copper-Nickel Pipe and Tube C70600 H3300 C7060 2871-CN102 17664 CuNi10Fe1Mn C71500 H3300 C7150 2871-CN107 17664 CuNi30Mn1Fe


ASTM JIS BS DIN B-467 Welded Copper-Nickel Pipe

C70600 H3320 C7060 2871-CN102 17664 CuNi10Fe1Mn C71500 H3320 C7150 2871-CN107 17664 CuNi30Mn1Fe CASTINGS

B-61 Steam or Valve Bronze Castings H5111 BC7 1400-LG4 --- B-62

Composition Bronze or Ounce H5111 BC6 1400-LG2 1705 G-CuSn5ZnPb Metal Castings

AISIgrade

UNS designation

EN / DINnumerical

designation

EN / DINsymbolicaldesignation

Austenitic stainless steel

USA, Japan Europe

JISgrade

201 S 201 00 1.4372 X12CrMnNiN17-7-5SUS 201 (EN)

QMS 5

202 S 202 00SUS 202

S 209 10

S 215 00

S 245 65

219 X4CrNiMn21-9-6

301 S 301 00 1.4310 X10CrNi18-8SUS 301 (EN)

301 L 1.4318 X2CrNiN18-7(EN)

302 S 302 00 1.4319 X10CrNi18-9SUS 302303 S 303 00 1.4305 X8CrNiS18-9SUS 303 (EN)

SUS 303 Cu

SUS 303 HS2

SUS 303 HS3

303 Se S 303 23 X10CrNiS18-9SUS 303 Se

304 S 304 00 1.4301 X6CrNi18-10SUS 304 (EN)

304 Cu S 304 30SUS XM 7

304 L S 304 03 1.4306 X2CrNi19-11SUS 304 L (EN)

304 L S 304 03 1.4307 X2CrNi18-9SUS 304 L (EN)

SUS 304 ELC

304 H S 304 09 1.4948 X8CrNi19-10SUS 304 H

SUS 304 Cu1

SUS 304 Cu2

S 304 15 1.4891

S 304 15 1.4818304 N S 304 51 X5CrNiN18-10SUS 304 N1

SUS 304 N2

304 LN S 304 53 1.4311 X2CrNiN18-10SUS 304 LN (EN)

SUS 304 MF

305 S 305 00 1.4303 X8CrNi18-12SUS 305 (EN)

SUS 305 J1

F 46 S 306 00 1.4361 X1CrNiSi18-15-4(EN)

S 306 15

308

309 S 309 00 1.4828 X15CrNi23-13

309 S 309 00 1.4829

309 S S 309 08 1.4828 X15CrNiSi20-12SUS 309 S

309 S S 309 08 1.4833 X6CrNi22-13SUS 309 S

309 S S 309 08 1.4833 X12CrNi23-13SUS 309 S

309 H S 309 09 1.4833309 Cb S 309 40

][®

www.weisz.com Steel grades equivalence tables Pág. 1

AISIgrade

UNS designation

EN / DINnumerical

designation



USA, Japan Europe

JISgrade

309 HCb S 309 41

310 1.4841 X15CrNiSi25-20

310 1.4845 X12CrNi25-20

SUS 310 ELC

310 L 1.4335 X1CrNi25-21(EN)

310 L 1.4466 X1CrNiMoN25-22-2(EN)

310 S S 310 08 1.4842 X6CrNi25-20SUS 310 S

310 S S 310 08 1.4845 X8CrNi25-21SUS 310 S (EN)

310 H S 310 09 1.4845

310 Cb S 310 40310 HCb S 310 41

310 HCbN S 310 42

310 SCB

S 310 50 1.4465 X1CrNiMoN25-25-2

S 310 50 1.4466 X1CrNiMoN25-22-2(EN)

F44 S 312 54 1.4547 X1CrNiMoCuN20-18-7(EN)

314 S 314 00 1.4841 X15CrNiSi25-20SUS 314

316 S 316 00 1.4401 X5CrNiMo17-12-2SUS 316 (EN)

316 S 316 00 1.4436 X3CrNiMo17-13-3SUS 316 (EN)

316 Cb S 316 40 1.4580 X6CrNiMoNb17-12-2(EN)

316 F S 316 20 1.4427 X6CrNiMoS18-11SUS 316 F

316 L S 316 03 1.4404 X2CrNiMo17-12-2SUS 316 L (EN)

316 L S 316 03 1.4406 X2CrNiMoN17-11-2SUS 316 L



316 L S 316 03 1.4441 X6CrNiMo17-11SUS 316 L

316 H S 319 09 1.4919 X6CrNiMo17-12SUS 316 H

SUS 316 J1

SUS 316 J1L

316 N S 316 51 1.4406 X2CrNiMoN17-11-2SUS 316 N (EN)

316 LS 1.4436 X3CrNiMo17-13-3(EN)

316 LS 1.4435 X2CrNiMo18-14-3(EN)

316 LN S 316 53 1.4406 X2CrNiMoN17-11-2SUS 316 LN

316 LN S 316 53 1.4429 X2CrNiMoN17-13-3SUS 316 LN (EN)

316 LN S 316 53 1.3952 X2CrNiMoN18-14-3SUS 316 LN

316 LN S 316 53 1.4910SUS 316 LN

316 S

316 Ti S 316 35 1.4571 X6CrNiMoTi17-12-2SUS 316 Ti (EN)

316 Ti S 316 35 1.4573 X10CrNiMoTi17-13-3SUS 316 Ti

317 S 317 00SUS 317SUS 317 J1

][®


AISIgrade

UNS designation

EN / DINnumerical

designation



USA, Japan Europe

JISgrade


317 L S 317 03 1.4434 X2CrNiMoN18-12-4(EN)

317 LM S 317 25

317 LN S 317 53 1.4439 X2CrNiMoN17-13-5(EN)

317 LMN S 317 26 1.4439 X2CrNiMoN17-13-5(EN)

F 48 S 317 26 1.4439 X2CrNiMoN17-13-5(EN)

318

319

319 L

321 S 321 00 1.4541 X6CrNiTi18-10SUS 321 (EN)

321 S 321 00 1.4878 X12CrNiTi18-9SUS 321

321 H S 321 09 1.4878 X12CrNiTi18-9SUS 321 H

321 H S 321 09 1.4941 X7CrNiTi18-11SUS 321 H

S 326 15

S 326 54

327 1.4821S 327 50

S 328 03

333

S 332 28

347 S 347 00 1.4550 X6CrNiNb18-10SUS 347 (EN)

347 H S 347 09 1.4961 X6CrNiNb18-12SUS 347 H

347 HFG

348 S 348 00 1.4878

348 H S 348 09S 353 15 1.4835

926 1.4529 X1NiCrMoCuN25-20-7(EN)

21-6-9 S219 04

22-13-5 S 209 10 1.3964 X2CrNiMnMoNNb21-16-5-3

16-8-2H

XM-10 S 219 00

XM-11 S 219 04

XM-15 S 381 00

SUS XM 15J1

XM-17 S 216 00

XM-18 S 216 03

XM-19 S 209 10 1.3964 X2CrNiMnMoNNb21-16-5-3

XM-19 S 209 10 1.3974 X2CrNiMnMoNNb23-17-6-3SUS XM 19

XM-21 S 304 52

XM-29 S 240 00XM-31 S 214 00

][®


AISIgrade

UNS designation

EN / DINnumerical

designation



USA, Japan Europe

JISgrade

1.4371 X2CrMnNiN17-7-5(EN)

1.4373 X12CrMnNiN18-9-5(EN)

1.4537 X1CrNiMoCuN25-25-5(EN)

1.4577 X5CrNiMoTi25-25

1.4848

X6CrNiCu18-10-4Kd

AISIgrade

UNS designation

EN / DINnumerical

designation


High temperature austenitic stainless steel

USA, Japan Europe

JISgrade

Alloy 286 S 662 86 1.4980 X5NiCrTi26-15

1.4961 X8CrNiNb16-3

1.4981 X8CrNiMoNb16-16

1.4988 X8CrNiMoVNb16-13

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Ferritic stainless steel

USA, Japan Europe

JISgrade

405 S 405 00SUS 405

409 S 409 00 1.4512 X2CrTi12(EN)

409 L

SUS 410 LC

410 S S 410 08 1.4516 X6CrNiTi12(EN)

410 Ti SUS 410 Ti

418

429 S 429 00SUS 429

430 S 430 00 1.4016 X6Cr17SUS 430 (EN)

430 F S 430 20SUS 430 F430 Cb S 430 40 1.4511 X3CrNb17

430 Ti S 430 35SUS 430 Ti

430 Ti S 430 36SUS 430 Ti

434 S 434 00 1.4113 X6CrMo17-1SUS 434

436 1.4536

439 S 430 35 1.4510 X3CrTi17(EN)

439 L

440 A S 440 00 1.4522

440 B S 440 00

441 1.4509 X2CrTiNb18(EN)

442

443 S 443 00SUS 443

444 S 444 00 1.4521 X2CrMoTi18-2QS 192 (EN)

446 S 446 00 1.4749 X18CrN28SUH 446

455490

501

XM-15

QS 25T

XM-27 S 446 27QS 261

XM-33 S 446 26

18-2 S 444 00 1.4521 X2CrMoTi18-2QS 192 (EN)

19-3 S 444 00 1.4521 X2CrMoTi18-2QS 192 (EN)

25-4-4 S 446 35

26-3-3 S 446 60

29-4 S 447 00

29-4C S 447 35

29-4-2 S 448 00

P9 S 504 00

S 890 40S 890 25

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Ferritic stainless steel

USA, Japan Europe

JISgrade

S 890 26

1.4000 X6Cr13(EN)

1.4002 X6CrAl13(EN)

1.4003 X2CrNi12(EN)

1.4017 X6CrNi17-1(EN)

1.4024 X15Cr13

1.4505

1.4506

1.4513 X2CrMoTi17-1(EN)

1.4520 X2CrTi17(EN)

1.4526 X6CrMoNb17-1(EN)

1.4575

1.4590 X2CrNbZr17(EN)

1.4592 X2CrMoTi29-4(EN)

1.4605 X2CrAlTi18-2(EN)

1.4724Y 4L

SIC 8

SIC 9

SIC 10

SIC 12

AISIgrade

UNS designation

EN / DINnumerical

designation


Heat resistant ferritic stainless steel

USA, Japan Europe

JISgrade

1.4713 X10CrAl7

1.4742 X10CrAl18

1.4781 X10CrAl24

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Duplex (ferritic / austenitic) stainless steel

USA, Japan Europe

JISgrade

2205 S 318 03 1.4462 X2CrNiMon22-5-3QS 2205 (EN)

2205 S 322 05

2304 S 323 04 1.4462 X2CrNiMoN22-5-3(EN)

2506 S 312 60

2507 S 327 50 1.4410 X2CrNiMoN25-7-4(EN)

2550 S 325 50 1.4460

2550 S 325 50 1.4507 X2CrNiMoCuN25-6-3QSA 2505 (EN)

F 50 S 312 00 1.4460 X3CrNiMoN27-5-2

F 51 S 318 03 1.4462 X2CrNiMoN22-5-3QS 2205 (EN)

F 51 S 322 05F 52 S 329 50

F 53 S 327 50 1.4410 X2CrNiMoN25-7-4(EN)

F 54 S 327 40

F 55 S 327 60 1.4501 X2CrNiMoCuWN25-7-4(EN)

S 312 54

S 315 00 1.4417 X2CrNiMoSi19-5QS 1905S 317 60

329 S 329 00SUS 329 J1

SUS 329 J2L

4462

1.4362 X2CrNiN23-4(EN)

S 392 74

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Martensitic stainless steel

USA, Japan Europe

JISgrade

403 S 403 00SUS 403

S 408 00

410 S 410 00 1.4006 X12Cr13SUS 410 (EN)

414

SUS 410 J1

410 S S 410 08 1.4006 X12Cr13(EN)

S 410 50 1.4030

F6NM S 415 00 1.4313 X3CrNiMo13-4(EN)

416 S 416 00SUS 416

SUS 416 HS2SUS 416 L

416Se

420 S 420 00 1.4021 X20Cr13(EN)

S 420 10 1.4021 X20Cr13(EN)

420 S 420 00 1.4028 X30Cr13SUS 420 J1 (EN)

SUS 420 J2SUS 420 J2C

SUS 420 J2L

420 F S 420 20SUS 420 F

F3NM S 424 00 1.4320 X2CrNiMo13-4

SUS 429 J1

431 S 431 00SUS 431

440 A S 440 00

440 C S 440 04SUS 440 C

SUS 440 FXM 12 S 155 00 1.4545 X5CrNiCuNb15-5-4

1.4031 X39Cr13(EN)

1.4034 X46Cr13(EN)

1.4116 X50CrMoV15(EN)

1.4122 X39CrMo17-1(EN)

1.4418 X4CrNiMo16-5-1(EN)

1.4922 X20CrMoV12-1

1.4935 X20CrMoWV12-1

QD 51

QPD 5

Y 2L

Y 2LF

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


High temperature martensitic stainless steel

USA, Japan Europe

JISgrade

F 91 1.4903 X10CrMoVNb9-1

1.4913 X19CrMoVNbN11-1

1.4922 X20CrMoV12-1

AISIgrade

UNS designation

EN / DINnumerical

designation


Antimagnetic stainless steel

USA, Japan Europe

JISgrade

QMR 1L

QMR 2LQMR 3LQMR 4L

QMR 5L

1.3951 X2CrNiMoN22-15

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Precipitation hardening stainless steel

USA, Japan Europe

JISgrade

1.4532 X8CrNiMoAl15-7-2(EN)

630 S 174 00 1.4542 X5CrNiCuNb16-4(EN)

1.4568 X7CrNiAl17-7(EN)

631 S 177 00SUS 631

16-6 PH

AM 350

AM 355

Alloy 15-5 PH

Alloy 17-4 PH

Alloy 17-7 PHAlloy 718

USS Stainless W

AISIgrade

UNS designation

EN / DINnumerical

designation


High molybdenum alloy

USA, Japan Europe

JISgrade

Alloy 29-4 S 447 35

Alloy 29-4-2

Alloy 254 SMO S 312 54 1.4547 X1CrNiMoCuN20-18-7(EN)

Alloy 256 MO N 08 926 1.4529 X1NiCrMoCuN25-20-7(EN)

Alloy 654 SMO S 326 54 1.4652

Alloy 904 L N 08 904 1.4539 X1NiCrMoCu25-20-5QS 2025 MC (EN)

Alloy 1925 HMO N 08 925

Alloy C-276 N 10 276

Alloy C-1008Alloy C-1010

Alloy F 49 S 345 65 1.4565 X3CrNiMnMoNbN23-17-5-3

N 08 320QS 2025 MT

1.4583 X6CrNiMoN18-12

X1NiCrMoCuN20-18-7

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


High nickel alloy

USA, Japan Europe

JISgrade

N 08 020QS 20 Cb3

N 08 028 1.4563 X1NiCrMoCu31-27-4QS 2830 (EN)

N 08 310

N 05 500 2.4375

Alloy B2 N 10 665

Alloy C4 N 06 455 2.4610

Alloy CP Gr2 R 50 400

Alloy C22 N 06 022 2.4602

N 06 059 2.4605

Alloy C-276 N 10 276 2.4819QA C276Alloy G N 06 007QA G

N 06 617 2.4663

Alloy G-3 N 06 985QA G3

Alloy G-30 N 06 030

Alloy K-500

Alloy L-605 R 30 605Alloy HX

Alloy MP35N

Alloy X N 06 002QA X

Alloy X-750

Alloy 6AC

Alloy 6XN N 08 367

Alloy 20

Alloy 25

Alloy 31 N 08 031 1.4562Alloy 41XX

Alloy 42

Alloy 43XX

Alloy 52

Alloy 59 N 06 059

Alloy 188

Alloy 205

Alloy 220

Alloy 222

Alloy 230

Alloy 253 RMA

Alloy 400 N 04 400 2.4360 NiCu30QA 400

Alloy 556

Alloy 600 N 06 600 2.4816 NiCr15FeNCF 600

Alloy 600 N 06 600 2.4640 NiCr15FeNCF 600Alloy 601 N 06 601 2.4851 NiCr23FeNCF 601

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


High nickel alloy

USA, Japan Europe

JISgrade

Alloy 602 2.4633

Alloy 622 N 06 622

Alloy 625 N 06 625 2.4856QA 625

Alloy 686

Alloy 690 N 06 690 2.4642 NiCr29Fe

JS 700 N 08 700QS 2025 M

Alloy 718 N 07 718 2.4668 NiCr19NbMo

Alloy 800 N 08 800 1.4558 X2NiCrAlTi32-20NCF 800

Alloy 800 N 08 800 1.4958 X5NiCrAlTi31-20

Alloy 800 N 08 800 1.4876 X10NiCrAlTi32-20NCF 800Alloy 800 H N 08 810 1.4958 X8NiCrAlTi32-21NCF 800 H

Alloy 800 HT N 08 811 1.4959 X8NiCrAlTi32-21

Alloy 825 N 08 825 2.4858 NiCr21MoNCF 825

N 08 840

Alloy 902

Cupronickel 10 C 706 00 2.0872 CuNi10FeCupronickel 30 C 715 00 2.0882 CuNi30Mn1Fe

Alloy 330 1.4864 X12NiCrSi36-16

1.4877

2.4973 NiCr19CoMo

AISIgrade

UNS designation

EN / DINnumerical

designation


High temperature alloy

USA, Japan Europe

JISgrade

Alloy A 286 S 662 86Alloy MP-35N R 30 035

Alloy X 750 N 07 750

Alloy 102 N 06 102

Alloy 253MA or F45 S 308 15 1.4835

Alloy 330 N 08 330

Alloy 333 N 06 333

Alloy 617 N 06 617

][®


AISIgrade

UNS designation

EN / DINnumerical

designation


Metals

USA, Japan Europe

JISgrade

Titanium 3Al 2.5V

Titanium Beta C

Titanium Gr 1 3.7025



Titanium Gr 4



Titanium Cr 12

Titanium T40Titanium T40 Gr2

Zircaloy 1

Zircaloy 2

Zirconium

Zirconium 2.5Nb

HafniumCopper

Nickel 200 N 02 200 2.4060Ni 200

Nickel 201 N 02 201 2.4061Ni 201

Nickel 200 N 02 200 2.4066

Nickel 201 N 02 201 2.4068

Nickel 270

][®


MARYLAND METRICS Technical Data Chart A short general listing of popular materials

International Material Grade Comparison Table The standards that correspond with DIN Material Numbers can only be compared approximately.

The use of these equivalents has to be evaluated on a case-by-case basis.

Steel

Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan

No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS

Plain Steel, Cast Steel, Free-Machining Steel

1.0332 St14 1008 14491CR 1447

1.1121 Ck10 1010 CC10 040A10 1264 S10C

1.0721 10S20 1108 210M15

1.0401 C15 1015 CC12 080M15 C15C16 1350 F.111 S15C

1.0402 C22 1020 CC20 050A20 C20C21 1450 F.112

1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K S15C

1.0036 USt37-3 FE37BFU

1.0715 9SMn28 1213 S250 230M07 CF9SMn28 1912 11SMn28 SUM22

1.0718 9SMnPb28 12L3 S250Pb CF9SMnPb28 1914 11SMnPb28 SUM22L

1.0501 C35 1035 CC35 060A35 C35 1550 F.113 S35C

1.0503 C45 1045 CC45 080M46 C45 1650 F.114 S45C

1.1158 Ck25 1025 XC25 070M25 C25 S25C

1.1183 Cf35 1035 XC38TS 060A35 C36 1572 S35C

1.1191 Ck45 1045 XC42 080M46 C45 1672 C45K S45C

1.1213 Cf53 1050 XC48TS 060A52 C53 1674 S50C

1.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 16Mo3

1.5423 16Mo5 4520 1503-245-420 16Mo5 16Mo5 SB450M

1.0050 St50-2 FE50 SM50YA

1.7242 16CrMo 4 18CrMo4 18CrMo4

1.7337 16CrMo 4 4 A387Gr.12Cl. A18CrMo45KW

1.7362 12CrMo 19 5 Z10CD5.05 3606-625 16CrMo205

1.0060 St60-2 FE60-2 SM570

1.0535 C55 1055 070M55 C55 1655 S55C

1.0601 C60 1060 CC55 080A62 C60 S60C

1.1203 Ck55 1055 XC55 070M55 C50 C55K S55C

1.1221 Ck60 1060 XC60 080A62 C60 1678 S58C

1.1545 C1051 C100KU SK3

1.1545 C105W1 C100KU SK3

1.0070 St70-2 FE70-2

1.7238 49CrMo4

1.7561 42CrV6

1.7701 51CrMoV4 51CDV4 51CrMoV4

Low-Alloy Steel, Cast Steel, Free-Machining Steel

1.2067 100Cr6 L3 Y100C6 BL3 100Cr6 SUJ2

1.2210 115CrV3 L2 100C3 107CrV3KU

1.2241 51CrV4

1.2419 105WCr6 105WC13 10WCr6 2140 105WCr5 SKS31



1.2419 105WCr6 105WC13 107WCr5KU SKS31

1.2542 45WCrV7 S1 BS1 45WCrV8KU 2710 45WCrSi8

1.2550 60WCrV7 S1 55WC20 58WCr9KU ~2710

1.2713 55NiCrMoV6 L6 55NCDV7 F.520.S SKH1;SKT4

1.2721 50NiCr13 ~2550

1.2762 75CrMoNiW67

1.2762 75CrMoNiW67

1.2842 90MnCrV8 O2 90MV8 BO2 88MnV8KU

1.3505 100Cr6 52100 100C6 534A99 100Cr6 2258 SUJ2

1.5622 14Ni6 ASTMA350LF5 16N6 14Ni6 15Ni6

1.5732 14NiCr10 3415 14NC11 16NiCr11 15NiCr11 SNC415(H)

1.5752 14NiCr14 3415;3310 12NC15 655M13 SNC815(H)

1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 33NiCrMo4 SNCM447

1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 2506 20NiCrMo2 SNCM220(H)

1.6546 40NiCrMo22 8740 311-TYPE7 40NiCrM02(KB) 40NiCrMo2 SNCM240

1.6582 35CrNiMo6 4340 35NCD6 817M40 35NiCrMo6(KB) 2541 SNCM447

1.6587 17CrNiMo6 18NCD6 820A16 14NiCrMo13

1.6657 14NiCrMo34 832M13 15NiCrMo13 14NiCrMo131

1.7033 34Cr4 5132 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H)

1.7035 41Cr4 5140 42C4 530M40 42Cr4 SCR440(H)

1.7045 42Cr4 5140 42C4TS 530A40 41Cr4 2245 42Cr4 SCr440

1.7131 16MnCr5 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415

1.7176 55Cr3 5155 55C3 527A60 SUP9(A)

1.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420;SCM430

1.7220 34CrMo4 4137;4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432;SCCRM3




1.0332 St14 1008 14491CR 1447

1.1121 Ck10 1010 CC10 040A10 1264 S10C

1.0721 10S20 1108 210M15

1.0401 C15 1015 CC12 080M15 C15C16 1350 F.111 S15C

1.0402 C22 1020 CC20 050A20 C20C21 1450 F.112 S20C,S22C

1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K S15C

1.0036 USt37-3 FE37BFU

1.0715 9SMn28 1213 S250 230M07 CF9SMn28 1912 11SMn28 SUM22

1.0718 9SMnPb28 12L3 S250Pb CF9SMnPb28 1914 11SMnPb28 SUM22L

1.0501 C35 1035 CC35 060A35 C35 1550 F.113 S35C

1.0503 C45 1045 CC45 080M46 C45 1650 F.114 S45C

1.1158 Ck25 1025 XC25 070M25 C25 S25C

1.1183 Cf35 1035 XC38TS 060A35 C36 1572 S35C

1.1191 Ck45 1045 XC42 080M46 C45 1672 C45K S45C

1.1213 Cf53 1050 XC48TS 060A52 C53 1674 S50C



1.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 16Mo3

1.5423 16Mo5 4520 1503-245-420 16Mo5 16Mo5 SB450M

1.0050 St50-2 FE50 SM50YA

1.7242 16CrMo 4 18CrMo4 18CrMo4

1.7337 16CrMo 4 4 A387Gr.12Cl. A18CrMo45KW

1.7362 12CrMo 19 5 Z10CD5.05 3606-625 16CrMo205

1.0060 St60-2 FE60-2 SM570

1.0535 C55 1055 070M55 C55 1655 S55C

1.0601 C60 1060 CC55 080A62 C60 S60C

1.1203 Ck55 1055 XC55 070M55 C50 C55K S55C

1.1221 Ck60 1060 XC60 080A62 C60 1678 S58C

1.1545 C1051 C100KU SK3

1.1545 C105W1 C100KU SK3

1.0070 St70-2 FE70-2

1.7238 49CrMo4

1.7561 42CrV6

1.7701 51CrMoV4 51CDV4 51CrMoV4

Low-Alloy Steel, Cast Steel, Free-Machining Steel

1.2067 100Cr6 L3 Y100C6 BL3 100Cr6 SUJ2

1.2210 115CrV3 L2 100C3 107CrV3KU

1.2241 51CrV4

1.2419 105WCr6 105WC13 10WCr6 2140 105WCr5 SKS31

1.2419 105WCr6 105WC13 107WCr5KU SKS31

1.2542 45WCrV7 S1 BS1 45WCrV8KU 2710 45WCrSi8

1.2550 60WCrV7 S1 55WC20 58WCr9KU ~2710

1.2713 55NiCrMoV6 L6 55NCDV7 F.520.S SKH1;SKT4

1.2721 50NiCr13 ~2550

1.2762 75CrMoNiW67

1.2762 75CrMoNiW67

1.2842 90MnCrV8 O2 90MV8 BO2 88MnV8KU

1.3505 100Cr6 52100 100C6 534A99 100Cr6 2258 SUJ2

1.5622 14Ni6 ASTMA350LF5 16N6 14Ni6 15Ni6

1.5732 14NiCr10 3415 14NC11 16NiCr11 15NiCr11 SNC415(H)

1.5752 14NiCr14 3415;3310 12NC15 655M13 SNC815(H)

1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 33NiCrMo4 SNCM447

1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 2506 20NiCrMo2 SNCM220(H)

1.6546 40NiCrMo22 8740 311-TYPE7 40NiCrM02(KB) 40NiCrMo2 SNCM240

1.6582 35CrNiMo6 4340 35NCD6 817M40 35NiCrMo6(KB) 2541 SNCM447

1.6587 17CrNiMo6 18NCD6 820A16 14NiCrMo13

1.6657 14NiCrMo34 832M13 15NiCrMo13 14NiCrMo131

1.7033 34Cr4 5132 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H)

1.7035 41Cr4 5140 42C4 530M40 42Cr4 SCR440(H)

1.7045 42Cr4 5140 42C4TS 530A40 41Cr4 2245 42Cr4 SCr440

1.7131 16MnCr5 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415



1.7176 55Cr3 5155 55C3 527A60 SUP9(A)

1.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420;SCM430

1.7220 34CrMo4 4137;4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432;SCCRM3


1.7223 41CrMo4 4140;4142 42CD4TS 708M40 41CrMo4 2244 42CrMo4 SCM440

1.7225 42CrMo4 4140 42CD4 708M40 42CrMo4 2244 42CrMo4 SCM440(H)

1.7262 15CrMo5 12CD4 2216 12CrMo4 SCM415(H)

1.7335 13CrMo4 4 ASTMA182 15CD3.5/4.5 1501-620-Gr27 14CrMo45 14CrMo45 SPVAF12

1.7361 32CrMo12 30CD12 722M24 32CrMo12 2240 F.124.A

1.7380 10CrMo9 10 ASTMA182F.22 SPV 1501-622Gr31;45

1.7715 14MoV6 3 1503-660-440 13MoCrV6

1.8159 50CrV4 6150 50CrV4 735A50 50CrV4 2230 51CrV4 SUP10

1.8159 50CrV4 6150 735A50 51CrV4 2230 SUP10

1.3501 100Cr2 E50100 100C2

1.5710 36NiCr6 3135 35NC6 640A35 SNC236

1.5736 36NiCr10 3435 30NC11 SNC631(H)

1.5755 31NiCr14 SNC836 18NC13 653M31

1.7733 24CrMoV55 20CDV6 21CrMoV511

1.7755 GS-45CrMoV104

1.8070 21CrMoV511 35NiCr9

1.8509 41CrALMo7 SACM645 40CAD6,12 905M39 41CrAlMo7 2940 41CrAlMo7

1.8523 39CrMoV139 897M39 36CrMoV12

1.2311 40CrMnMo7 35CrMo8KU

1.4882 X50CrMnNiNbN219 Z50CMNNb21.09

1.5864 35NiCr18

High-Alloy Steel, Cast Steel

1.2343 X38CrMoV51 H11 Z38CDV5 BH11 X37CrMoV51KU X37CrMoV5 SKD6

1.2344 X40CrMoV51 H13 Z40CDV5 BH13 X40CrMoV511KU 2242 X40CrMoV5 SKD61

1.2379 X155CrVMo121 D2 Z160CDV12 BD2 X155CrVMo121KU SKD11

1.2436 X210CrW12 X215CrW121KU 2312 X210CrW12 SKD2

1.2581 X30WCrV93 H21 Z30WCV9 BH21 X30WCrV93KU X30WCrV9 SKD5

1.2601 X 165CrMoV12 X165CrMoW12KU 2310 X160CrMoV12

1.2606 X37CrMoW 51 H12 Z35CWDV5 BH12 X35CrMoW05KU F.537 SKD62

1.5662 X8Ni9 ASTMA353 1501.509; 50 X10Ni9 XBNi09 SL9N53

1.5680 12Ni19 2515 Z18N5

1.3202 S12-1-4-5 BT15 HS12-1-5-5 12-1-5-5

1.3207 S10-4-3-10 Z130WKCDV BT42 HS10-4-3-10 SKH57

1.3243 S6-5-2-5 T15 KCV06-05-05-04-02 HS6-5-2-5 2723 6-5-2-5 SKH55

1.3246 S7-4-2-5 Z110WKCDV07-05-04 HS7-4-2-5 7-4-2-5 M35

1.3247 S2-10-1-8 Z110DKCWV09-08-04 BM42 HS2-9-1-8 2-10-1-8 M41 SKH51

1.3249 S2-9-2-8 M42 BM34 2-9-2-8

1.3343 S6-5-2 M35 Z85WDCV BM2 HS6-5-2-5 2722 SKH9; SKH51

Stainless Steel, Cast Steel

1.4000 X6Cr13 403 Z6C13 403S17 X6Cr3 2301 F.3110 SUS403



1.4001 X6Cr14 F.8401 410S, 429

1.4002 X6CrAl13 405 Z8CA12 405S17 X6CrAl13 SUS405

1.4006 (G-)X10Cr13 SUS410 Z10C13 410S21 X12Cr13 2302 F.3401 SUS410

1.4016 X8Cr17 430 Z8C17 430S15 X8Cr17 2320 F.3113 SUS430

1.4021 X20Cr13 420 Z20C13 420S37 X20Cr13 2303 SUS420J1

1.4027 G-X20Cr14 Z20C13M 420C29 SCS2

1.4086 G-X120Cr29 452C11

1.4104 X12CrMoS17 430F Z10CF17 441S29 X10CrS17 2383 F.3117 SUS430F

1.4113 X6CrMo17 434 Z8CD1701 434S17 X8CrMo17 2325 SUS434

1.4340 G-X40CrNi274

1.4417 X2CrNiMoSi195 S31500 2376

1.4720 X20CrMo13

1.4724 X10CrA113 405 Z10C13 403S17 X10CrA112 F.311 SUS405

1.4742 X10CrA118 430 Z10CAS18 430S15 X8Cr17 F.3113 SUS430

1.4762 X10CrA124 446 Z10CAS24 X16Cr26 2322 SUH446

1.4034 X46Cr13 Z40CM 420S45 X40Cr14 2304 F.3405

1.4057 X20CrNi17 431 Z6CNi6.02 431S29 X16CrNi16 2321 SUS431

1.4125 X105CrMo17 Z100CD17 X 105CrMo17 SUS440C

Stainless Steel and Cast Iron



Austenitic Stainless Steel

1.4301 X5CrNi189 304 Z6CN18.09 304S15 X5CrNi1810 2332 F.3551 SUS304

1.4310 X12CrNi177 301 Z12CN17.07 301S21 X2CrNi1807 2331 F.3517 SUS301

1.4311 X2CrNiN1810 304LN Z2CN18.10 304S62 X2CrNiN1810 2371 SUS304LN

1.4312 G-X10CrNi188 Z10CN18.9M 302C25

1.4350 X5CrNi189 304 Z6CN18.09 304S31 X5CrNi1810 2332/2333 F.3551

1.4362 X2CrNiN234 S32304 Z2CN23-04AZ 2327

1.4401 X5CrNiMo17122 316 Z6CND17.11 316S16 X5CrNiMo1712 2347 F.3543 SUS316

1.4404 X2CrNiMo1810 316L Z2CND17.12 316S12 X2CrNiMo1712 2343/2348/2553 SUS316

1.4410 G-X10CrNiMo189 Z5CND20.12M

1.4429 X2CrNiMoN17133 316LN Z2CND17.13 316S63 X2CrNiMoN1713 2375 SUS316LN

1.4435 X2CrNiMo18143 316L Z2CND17.12 316S13 X2CrNiMo1712 2353 SCS16

1.4436 X5CrNiMo17133 316 Z6CND18-12-03 316S33 X8CrNiMo1713 2343/2347 SUS316

1.4438 X2CrNiMo18164 317L Z2CND19.15 317S12 X2CrNiMo1816 2367 SUS317L

1.4500 G-X7NiCrMoCuNb2520 23NCDU25.20M

1.4541 X10CrNiMoTi1810 321 Z6CNT18.10 321S12 X6CrNiTi1811 2337 F.3553F.3523 SUS321

1.4550 X10CrNiNb 347 Z6CNNb18.10 347S17 X6CrNiNb1811 2338 F.3552F.3524 SUS347

1.4552 G-X7CrNiNb189 Z4CNNb19.10M 347C17

1.4571 X10CrNiMoTi1810 316Ti Z6NDT17.12 320S17 X6CrNiMoTi1712 2350 F.3535 SUS316TI

1.4583 X10CrNiMoNb1812 318 Z6CNDN1713B X6CrNiMoNb

1.4585 G-X7CrNiMoCuNb1818 X6CrNiMoTi1712

1.4828 X15CrNiSi2012 309 Z15CNS20.12 309S24 SUH309



1.4845 X12CrNi2521 310S Z12CN2520 310S24 X6CrNi2520 2361 F.331 SUH310; SUS310S

Austenitic/Ferritic Stainless Steel (Duplex)

1.4460 X8CrNiMo275 S32900 2324 SUS329J1

1.4462 X2CrNiMoN2253 Z2CND22-05-03 2977

1.4821 X20CrNiSi254 Z20CNS25.04

1.4823 G-X40CrNiSi274

Gray Cast Iron

0.6010 GG10 CLASS20 Ft10D G10 110 FC100

0.6015 GG15 CLASS25 Ft15D GRADE150 G15 115 FG15 FC150





0.6040 GG40 CLASS55 Ft40D GRADE400 140 FC400

Gray Cast Iron with Nodular Graphite

0.7033 GGG35.3 0717-15 FCD350

0.7040 GGG40 60-40-18 FCS400-12 SNG420/12 GGG40 0717-02 GGG40 FCD400

0.7043 GGG40.3 FGS370-17 SNG370/17 0717-12 FCD400

0.7050 GGG50 80-55-06 FGS500-7 SNG500/7 GGG50 0727-02 GGG50 FCD500

0.7060 GGG60 FGS600-3 SNG600/3 GGG60 0732-03 GGG60 FCD600

0.7070 GGG70 100-70-03 FGS700-2 SNG700/2 GGG70 0737-01 GGG70 FCD700

White malleable Cast Iron

0.8040 GTW-40 MB40-10 W410/4 GMB40 GTW40

0.8045 GTW-45 GMB45 GTW45

0.8055 GTW-55 GTW55

0.8065 GTW-65 GTW65

0.8135 GTS-35 32510 MN35-10 B340/12 810 GTS35

0.8145 GTS-45 40010 P440/7 852 GTS45

0.8035 GTW-35 MB35-7 W340/3 GTW35

0.8155 GTS-55 50005 MP50-5 P510/4 854 GTS55

0.8165 GTS-65 70003 MP60-3 P570/3 856 GTS65

0.8170 GTS-70 90001 M870-2 P690/2 0862; 0864 GTS70



Non-Ferrous Materials

Aluminium Alloys

3.0255 Al99.5 1000 A59050C L31/34/36

3.3315 AlMg1

3.1655 AlCuSiPb

3.1754 G-AlCu5Ni1,5 3.4345 AlZnMgCu0,5 AZ4GU/9051 L86 811-04 7050

3.2373 G-AlSi9Mg

3.2381 G-AlSi10Mg

3.2382 GD-AlSi10Mg



3.2383 G-AlSi10Mg (Cu) A360.2 LM9 4253

3.2383 GK-AlSi10Mg (Cu) A360.2 LM9 4253

3.2581 G-AlSi12 A413.2 LM6 4261

3.2582 GD-AlSi12 A413.0 4247 A6061

3.2583 G-AlSi12 (Cu) A413.1 LM20 4260 ADC12

3.3561 G-AlMg5 GD-AlSi12 A-SU 12 LN5 4252 AC4A

3.5101 G-MgZn4SE1Zr1 ZE41 G-Z4TR MAG5

3.5103 MgSE3Zn2Zr1 EZ33 G-TR3Z2 MAG6

3.5106 G-MgAg3SE2Zr1 QE22 G-Ag22,5 MAG12

3.5812 G-MgAl8Zn1 AZ81 G-A9 MAG1

3.5912 G-MgAl9Zn1 AZ91 G-A9Z1 MAG7

2.1871 G-AlCu4TiMg

3.2371 G-AlSi7Mg 4218B

Copper Alloys

2.1090 G-CuSn7ZnPb C93200 U-E7Z5Pb4

2.1096 G-CuSn5ZnPb C83600 U-E5Pb5Z5 LG2

2.1098 G-CuSn2ZnPb

2.1176 G-CuPb10Sn C93700 U-E10Pb10 LB2

2.1182 G-CuPb15Sn C93800 U-Pb15E8 LB1

2.0240 CuZn15 C23000 CuZn15 CZ102

2.0265 CuZn30 C26000 CuZn30 CZ106

2.0321 CuZn37 C27200, C27700 CuZn36, CuZn37 CZ108 C2700,C2720

2.0592 G-CuZn35Al1 C86500 U-Z36N3 HTB1

2.0596 G-CuZn34Al2 C86200 U-Z36N3 HTB1

2.1188 G-CuPb20Sn C94100 U-Pb20 LB5

2.1292 G-CuCrF35 C81500 CC1-FF

2.1293 CuCrZr C18200 U-Cr0,8Zr CC102

2.0966 CuAl10Ni5Fe4 C63000 U-A10N Ca104

2.0975 G-CuAl10Ni B-148-52

2.1050 G-CuSn10 C90700 CT1

2.1052 G-CuSn12 C90800 UE12P Pb2

High-Temp Alloys

Werkstoff Germany U.S.A. France Great Britain US Sweden Spain Japan

No. DIN AISI/SAE UNS AFNOR BS US Trade Designation SS UNE JIS

Super-Alloys Fe-based

1.4558 X2NiCrAlTi3220 N08800 NA15 Incoloy 800

1.4562 X1NiCrMoCu32287 N08031

1.4563 X1NiCrMoCuN31274 N08028 Z1NCDU31.27

1.4864 X12NiCrSi 330 Z12NCS35.16 SUH330

1.4864 X12NiCrSi3616 N08330 Z12NCS35.16 NA17 SUH330

1.4958 X5NiCrAlTi3120

1.4977 X40CoCrNi2020 Z42CNKDWNb



S66286 A-286

S41800 Greek Ascoloy

R30556 Haynes 556 (HS556)

R30155 N155

Super-Alloys Co-based

R30188 Haynes 188

R30605 L605 (Haynes 25)

MARM-302, 322, 509

Stellite 6, 21, 31

Super-alloys Ni-based

2.4360 NiCu30Fe NU30 NA13 Monel 400

2.4610 NiMo16Cr16Ti Hastelloy C-4

2.4630 NiCr20Ti N06075 NC20T HR5, 203-4 Nimonic 75

2.4642 NiCr29Fe NC30Fe Inconel 690

2.4810 G-NiMo30 N10276 Hastelloy C

2.4856 NiCr22Mo9Nb N06625 NC22FeDNb NA21 Inconel 625

2.4858 NiCr21Mo N08825 NC21FeDU NA16 Incoloy 825

2.4375 NiCu30 Al NU30AT NA18 Monel K-500

2.4668 NiCr19FeNbMo N07718 NC19FeNb Inconel 718

2.4669 NiCr15Fe7TiAl N07750 NC15TNbA Inconel X-750

2.4685 G-NiMo28 N10001 Hastelloy B

2.4694 NiCr16Fe7TiAl N00751 Inconel 751

Titanium and titanium alloys

3.7025 Ti 1 R50250 2TA1

3.7124 TiCu2 2TA21-24

3.7195 TiAl3V2.5

3.7225 Ti1Pd R52250 TP1

3.7115 TiAl5Sn2

3.7145 TiAl6Sn2Zr4Mo2Si R54620

3.7165 TiAl6V4 R56400 T-A6V TA10-13; TA28 TiAl6V4

3.7175 TiAl6V6Sn2 R56620 Ti6V6Al2Sn

3.7185 TiAl4Mo4Sn2 TA45-51; TA57

Hardened Materials



White Cast Iron

0.9620 G-X260NiCr42 Ni- Hard 2 Grade 2A 0512-00

0.9625 G-X330NiCr42 Ni- Hard 1 Grade 2B 0513-00

0.9630 G-X300CrNiSi952 Ni- Hard 4

0.9635 G-X300CrMo153

Hardened Cast Iron

0.9640 G-X300CrMoNi1521



0.9645 G-X260CrMoNi2021

0.9650 G-X260Cr27 A532IIIA25%Cr Grade 3D 0466-00

0.9655 G-X300CrMo271

0.9655 G-X300CrMo271 A532IIIA25%Cr Grade 3E

copyright 2010 maryland metrics Data courtesy of Kennametal

Documents

Equivalent Material Grades