Entrance Gate and Porch_boq

Page: 1/24

PROPOSED " M/s PRESIDENCY UNIVERSITY B SCHOOL - ENTRANCE PORCH " AT DIBBUR, BANGALOREENTRANCE GATE AND PORCH

Sl. No. DESCRIPTION Unit

A EARTH WORK

1 A1 Cum

2 A2 Cum

3 A3 Cum

A5

4 A5.a CumA6

5 A6.a Cum

6 A7 Cum

7 A8 Cum

TenderItem No.

General earth work excavation in all kinds of soil for lowering & leveling the ground other than for foundation, disposing the surplus earth to a place away from the site not objected by anybody, including re-filling the depressions wherever necessary, de- watering, shoring, strutting, etc., complete all as per specification, drawing and direction - up to 3.0 m (avg) from the existing ground level , with respect to grid level and natural ground level including all lead & lift (block leveling shall be recorded and approved by Architects before start of excavation).

Item same as that of item #1 but between 3.0 5.0m (From the existing ground level).Item same as that of item #1 but in Hard rock with Drilling/Blasting as per site condition up to 3.0m depth from the existing ground level.Earth work excavation in ordinary/hard soils, decomposed /soft rock etc for foundation trenches / column footings, stacking the excavated earth, back filling the trenches in layers not more than 150mm, watering, consolidating, disposing the surplus earth to a place away from the site not objected by anybody, de-watering, shoring, strutting, etc complete all as per specification, direction and drawing. The depth for excavation is measured from the Existing level. (Level around the trench before start of excavation for footing) (Level with respect to Natural Ground Level at respective grid levels)

Depth up to 2.5m below NGL / Existing level (with respect to grid level )Item same as that of item #A5 but in soft and decomposed rocks from the existing ground level.

Depth up to 1.5m Item same as that of item #A5 but in Hard rock with chiseling / Drilling or Blasting as per the site condition up to an average depth of 1.5m lift from the level excavated for general earth excavation.

Earth filling below flooring / plinth with available approved earth, in layers not more than 150mm thick, including watering, consolidating etc complete all as per specification, drawing and direction.

Page: 2/24

Sl. No. DESCRIPTION UnitTenderItem No.

8 A10 Cum

9 A11 Sqm

B PLAIN CEMENT CONCRETE

10 B1 Cum

11 B2 Cum

12 B4 Sqm

C MASONRY WORKS

Providing and laying boulder stone soling using 100 to 150mm size granite stone laid to required gradient & level including packing with stone aggregates, supplying and spreading of binding materials like moorum and sand, watering and consolidating after every fresh course of spread etc; complete all as per specification, drawing and direction.

Providing and injecting Anti-Termite treatment by a specialized approved agency with a guarantee for 10 (ten) years etc; complete all as per specification, direction and drawing. Only plinth area (basement / ground) shall be measured and paid for.

Providing and laying PCC 1:4:8 bed concrete at all levels below footings of Foundation, Column, Retaining Wall etc / below flooring, using 40mm and down size graded granite stone aggregates including machine mixing, tamping, curing, shuttering wherever necessary etc; complete all as per specification, drawing and directions.

Providing and laying PCC 1:3:6 in Damp Proof Course on SSM Foundation / sills / parapet ledge concreting and for any other such works of thickness not more than 75mm, using 20mm and down size graded granite stone aggregates mixed with water proof compound, (FOSROC make, used as directed by the manufacturer) including finishing the exposed surface in CM 1:3, machine mixing, shuttering, tamping, curing etc, complete all as per specification, drawing and direction.

Providing and laying PCC 1:2:4 concrete of 75mm thick for flagging concrete using 20mm and down size graded granite stone aggregates, to a required gradient/level etc, .including finishing the top surface with 12mm thick plaster in CM 1:4, laid in alternate bays, joints neatly finished, machine mixing, tamping, curing, shuttering wherever necessary etc, complete all as per specification, drawing and direction.

Page: 3/24


13 C1 Cum

14 C2 Sqm

15 C3 Sqm

16 C4 Sqm

D

NOTE: The rate quoted for all items (under masonry section) include for scaffolding, platforms and staging required in the execution of the work at any height/floor, hacking or roughening of the concrete surface coming in contact with the masonry for bondage, raking out the joints to the required depth, either for plastering or pointing, curing the masonry for the required period, making good the chases done to house GI / PVC, pipe/conduits for the water supply / sanitary / electrical works by using appropriate/ approved material, providing through bond stone at every 1500mm in each course of stone masonry etc;

Providing and constructing size stone masonry in foundation / Plinth/ Retaining wall in CM 1:6 using granite size stone in courses not less than 200mm high with stone edges, hammer/chisel dressed including providing through bond stone at every 1500mm interval in each course, curing etc; complete all as per specification, drawing and directions.

Providing and constructing masonry in superstructure using approved quality/make pre-cast solid cement concrete block of compressive strength between 35 to 40 kg/sq cm & of size 400 x 200 x 200 mm, constructed in CM 1:6 at any or all levels including providing of cutouts / openings where specified/required, with necessary scaffolding, curing, packing between column / beam / roof slab and masonry, also filling of voids / chases created by chasing of wall for water supply / electrical works etc. with appropriate / approved material as directed etc., complete all as per specification, drawings and directions.

Item same as above (item#C2) but using blocks of size 400x150x200mm. Item same as that of item # C2 but using blocks of size 400x100x200mm in Internal partition wall / Balcony / Parapet walls including laying 2 nos of 6mm dia MS rod embedded in 3 thick concrete band (1:2:4) in every fifth course (quote rate excluding the cost of Reinforcement Steel).

REINFORCED CEMENT CONCRETE WORKS - M20 grade concrete-with film coated ply shuttering- Basic Price of RMC considered - Rs 4250/-cmt

Page: 4/24


17 D1 Cum18 D2 Item same as above but with Ready Mix Concrete Cum19 D3 M 20 in Column Pedestal. (INSITU). Cum20 D4 Item same as above but with Ready Mix Concrete Cum21 D5 M 20 in Plinth beams/Strap Beams.(INSITU) Cum22 D6 Item same as above but with Ready Mix Concrete Cum23 D7 M 20 in Column Shafts.(INSITU) Cum24 D8 Item same as above but with Ready Mix Concrete Cum25 D9 M 20 in Roof beams(INSITU) Cum26 D10 Item same as above but with Ready Mix Concrete Cum

27 D16 M 20 in Sloping Floor / Roof slab and its projections.(INSITU) Cum

28 D17 Item same as above but with Ready Mix Concrete Cum29 D18 M 20 in R.C.C Grade slab concreting in flooring. Cum30 D19 Item same as above but with Ready Mix Concrete Cum

31 D20 Cum

32 D21 Item same as above but with Ready Mix Concrete Cum33 D26 M 20 in retaining wall (INSITU) Cum

NOTE: Providing and laying controlled reinforced cement concrete conforming to grades as specified (IS 456-2000) using 20mm and down size graded aggregates, necessary admixtures approved by consultants, excluding the cost of steel, its fabrication and cost of admixtures, including scaffolding, shuttering/ all form works to be of 12mm thk film coated ply shuttering and de- shuttering of the same, machine/hand-mixing where not mentioned as RMC, RMC where required, RCC members of any sizes and shapes unless mentioned, vibrating to the extent not to get any honey-comb, curing, hacking of the concrete surface to receive plastering, casting of concrete at all levels including lead and lift, to achieve true line and level, placing in position in concrete bed any inserts like PVC pipes /MS plate / rods / bolts etc, cost to exclude the cost of inserts,, complete all as per specification, drawing and directions.(B.P. of R.M.C 4250=00 / Cum(Including Pumping). All the shuttering/form work are to be considered up to 4.0m-5.0m clear floor to floor height)

M 20 in footing - Foundation,Column Footing & Retaining wall foundation.(INSITU).

M 20 in waist slab, riser, tread and landing slab of staircase (Common staircase).

Page: 5/24


34 D27 Item same as above but with Ready Mix Concrete Cum35 D28 M 20 in Lintels. Cum36 D31 M20 in Form finish(Exposed Concrete) concrete wall Cum37 D32 M 20 for machinery foundations Cum

38 D34 Sqm

39 D37 Extra for reinforced cement concrete grade M 25 in lieu of M20. Cum

40 D39 Extra for reinforced cement concrete grade M 30 in lieu of M20. Cum41 D41 RCC Pergolas -100mm thk Sqm

42 D41 Sqm

E FLOORING WORKS

43 E2 Sqm

44 E3 Rmt

Providing and casting 75mm thick loft / counter slab/ chajjas slab using M20 grade concrete, including plastering all the exposed concrete surface in CM 1:4 finished with a coat of lime rendering/sand-faced / finished smooth with cement slurry, providing drip mould or drip groove, etc; complete all as per specification, drawing and directions.(INSITU)

Extra for double height staging of form work above 4.00m and up to 6.00m for flat roof Measurement will be of plan area.

Providing and Laying of 20mm thick Pre Polished Granite slabs laid in pattern as flooring, over a bed of CM 1:6,25mm thick avg/ papar joints/ joints as required / grooves are neatly filled and finished in white cement / bal grout mixed with coloring pigment to match the color / shade of the slab including cutting, laying to the required pattern and gradient, curing, acid washing, cleaning, waxing etc., complete all as per specification, drawing and direction.(Basic Rate Rs. 80.00/Sqft) - Lobby, Corridor, Waiting Area, Common area, Library, Class rooms, Faculty, Computer lab, Office Building & Auditorium.

Providing and Fixing of 10mm thick Pre- polished Granite slab strips of height 75mm in skirting, fixed in flush with plastered wall surface over a backing coat of 12mm thick CM 1:4 set in cement paste, joints/grooves neatly filled and finished with white cement/bal grout mixed with coloring pigment to match the shade/color of the slab, including cutting, laying to the required pattern, treating the exposed edges/nosing as in the drawing, acid washing, cleaning, waxing, curing etc complete all as per specifications, drawing & direction. (Basic Rate Rs.80/Sqft).

Page: 6/24


45 E4

a) Sqm

46 E5 Sqm

F WATERPROOFING WORKS

47 F1 Sqm

48 F2 Sqm

Providing and Laying of approved quality / make / color / shade Granite flooring of approved size for flooring laid over a bed of CM 1:6, 25mm thick avg, laid to required pattern/gradient/ as shown in drawing, including joints / grooves neatly filled and finished with white cement / bal grout mixed with coloring pigments to match the color / shade of the tile including cutting, curing, acid washing, cleaning, etc,. complete all as per specification, drawing and direction.

Toilet Flooring (Basic Rate: Rs. 70 / Sqft )Providing and Fixing Dadoing for walls in toilet blocks using approved size quality / make / color / shade Granite over a backing coat of 12 mm thick CM 1:4, set in cement paste, fixed to the required pattern and gradient, joints/grooves neatly filled and finished with white cement paste/bal grout mixed with coloring pigment to match the color/shade of the tile, including cutting, curing, cleaning, acid washing etc. complete all as per specifications, drawing and direction. (Basic Rate: Rs. 70.00/Sqft)

Providing Waterproofing for Terrace including cleaning, removal of dead mortar, scraping and applying brush bond ( as per consultant approval ) to the concrete surfaces, providing waterproofing for Terrace by surface method of brick coba average thickness 100mm with waterproof ad-mixture of TAPE CRATE or equivalent as per manufactures specification approved by Consultants, top finished with CM 1:3 mixed with water proofing compound, and impression making 300mm x 300mm square with 3mm rod. Treatment to continue along parapet upto 300mm height in shape of round wata, curing etc., Cost to include the treatment along parapet and no measurement will be accounted for the parapet treatment. (Only plan area shall be accounted)

Preparing of the surface in vertical surfaces of the walls/Lift and such other places and plastering in CM 1:3 mixed with waterproof ad-mixture as per manufactures specification approved by Consultants with a Minimum guarantee period of 10 (ten) years (FOSROC make used as per the manufacturer's specification) and finished smooth/sand faced/rough, including curing, scaffolding etc; complete all as per specification and direction and drawing. Plan area will be measured and paid for.

Page: 7/24


49 F3 Sqm

50 F4 Cum

51 F6 Sqm

G PLASTERING WORKS

52 G1 Sqm

53 G2 Sqm

54 G3 Sqm

55 G4 Sqm

Preparing the surface in Toilet and sunken portion and such other places and plastering in CM 1:3 mixed with waterproof ad-mixture as per manufactures specification approved by Consultants with a Minimum guarantee period of 10 years (FOSROC make used as per the manufacturer's specification) and finished smooth/sand faced/rough, including curing, scaffolding etc; complete all as per specification and direction and drawing. (Only plan area shall be accounted for measurements)

Providing and laying cinder concrete 1:15(1 cement:15 cinder) well mixed,filled in sunken portion and the top surface finished with 40mm thick M20 grade concrete using 20mm and down size graded granite aggregates to receive flooring ,including tamping,consolidating,curing,etc,complete all as per specifications, drawing and directions.

Providing and laying Screed concrete of 40mm thick using M15 concrete using 20mm down size graded granite to receive flooring, including tamping, consolidating, curing,etc., complete all as per specification, drawing and directions.

Preparing the Ceiling/ beam sides /concrete surface/columns and plastering with 12mm thick CM 1:4 including finishing with a thin coat of lime paste, scaffolding, curing etc. complete all as per specification, directions and drawing

Preparing the Internal surface of the wall and other concrete surface, and plastering with 12mm thick CM 1:6 including plastering and finishing of cut-out / openings, finishing with a thin coat of lime paste, scaffolding, curing etc. complete all as per specification, drawing and directions.

Preparing the External surface of walls / concrete surface and plastering with 20mm thick in CM 1:6 applied in two coats of 12mm and 6mm respectively, including plastering and finishing of cut-out/openings, finishing smooth or sand faced as required, curing scaffolding etc, complete all as per specification, drawing and directions.

Preparing the surface and providing Rough plaster either for internal or external surface of the walls in cm 1:6 of thickness 12mm minimum, curing, scaffolding, etc; complete all as per specification, drawing and directions.

Page: 8/24

Sl. No. DESCRIPTION UnitTenderItem No.H PAINTING WORKS

56 H2 Sqm

57 H2 Sqm

58 H4 Sqm

59 H5 Sqm

60 H6 Sqm

61 H7 Sqm

I DOORS & WINDOWS

Preparing the plastered Ceiling surfaces and applying two or more coats of approved quality/make/color/shade Plastic Emulsion paint including, primer and putty works, scaffolding, etc. complete all as per specification,drawing and direction.

Preparing the plastered Internal wall surfaces and applying two or more coats of approved quality/make/color/shade Plastic Emulsion paint including, primer and putty works, scaffolding, etc. complete all as per specification,drawing and direction.

Preparing the external plastered surface of the wall and applying Texture paint of approved quality color/shade/ exterior grade paint with necessary base preparation and applying two coats of approved quality color/shade/make exterior emulsion paint over a coat of primer, at all heights / levels / floors , etc., complete all as per specification,drawing and direction. (Considered B.P Rs 30.00 /sft approved from architect).

Providing and painting steel surface with two coats of synthetics enamel paint Asian / Nerolac or approved equivalent over a coat of primer(Zinc chromite) after scrapping the surface using sand paper, cleaning etc to a required finish all as per specifications, drawing and directions.

Providing aggregate finish plastering to the exterior walls in 2 (Two) coats, consisting of a base coat of 12mm thick in CM 1:4 and finishing with additional coat of 6mm and below graded granite aggregate mixed in CM 1:3 and dashed over the base coat, the surface is washed with the sponge and water, when the surface is thumb print hard, in order to expose the aggregate surface including curing, scaffolding etc., complete all as per specification, drawing and directions.

Providing and Laying of approved quality Natural Stones in cladding in External walls over a backing coat of CM 1:6, joints neatly done with a paper joint/grooves as shown in the drawing, including cutting, curing, washing, cleaning, waxing, etc complete all as per specification, drawing and direction. (Basic Rate: Rs.50.00/Sqft)

All doors frames to be in Hard wood basic price @ Rs.1400/cft

Page: 9/24


62 I2 Sqm

63 I2 Sqm

64 I3 Sqm

Providing and fixing of DOORS-Single Shutters made of 125 X 75mm hard wood frame and approved quality/make 25mm thick flush shutter including frames fixed in the masonry using MS hold fast of appropriate size and thickness embedded in PCC 1:3:6 using 20mm and down size graded granite stone aggregates as directed,the rate to be also inclusive of providing and fixing of all hardware fittings / fixture,including painting the frames and shutters surface with two or more coats of approved color/make enamel paint including a coat of primer on both the sides and cleaning, cutting, plaining, sanding, waxing, etc, complete all as per specifications, direction and drawings. [ Basic price of Hardware fittings @ Rs. 60/sft , Basic price of Hard wood to be 1400 per Cft].

Providing and fixing of DOORS-Single Shutters made of 125 X 75mm hard wood frame and approved quality/make 25mm thick flush shutter including frames fixed in the masonry using MS hold fast of appropriate size and thickness embedded in PCC 1:3:6 using 20mm and down size graded granite stone aggregates as directed,the rate to be also inclusive of providing and fixing of all hardware fittings / fixture,including painting the frames and shutters surface with two or more coats of approved color/make enamel paint including a coat of primer on both the sides and cleaning, cutting, plaining, sanding, waxing, etc, complete all as per specifications, direction and drawings. [ Basic price of Hardware fittings @ Rs. 60/sft , Basic price of Hard wood to be 1400 per Cft].

Providing and fixing in position three track natural anodised (min.25 micron) aluminium windows in single or composite sections either openable or fixed, with sliding glazed shutters in two tracks with 4mm thick clear glazing,(and provision only for a sliding wire mesh shutter) all made in 12 guage aluminium sections as approved by the architect, and as per drawing and as directed. The min. sectional wt of aluminium window frame to be 1.448 kg./mt. and that of shutter to be 0.66 kg./mt. All windows to be protected with paper tape during execution. The window frames to be anchored to the walls with anchor fastners and sealing all round gaps with silicon sealant and all incidental work complete and as directed.

Page: 10/24


65 I4 Sqm

J STEEL WORKS

66 J1 MT

67 J3 MT

68 J5 MT

Providing and fixing 20 micron anodized aluminium ventilators with glazed shutter, provision for exhaust fan made out of extruded sections of min. wt. 0.658 kg./mt. for frames,4mm thick clear glazing, and anchored to the walls with anchor fasteners and sealing all around gaps with silicon sealant and all incidental work complete as per drawing and as directed.

Supplying, fabricating and placing in position MS/TOR steel reinforcement of various diameter and of grade conforming to IS 1786 for RCC works including, transportation, straightening, cutting, bending, welding at places required, placing in position and tying the rods with binding wire, work at all levels / floors, chairs, authorized laps shall be measured for billing, standard weights shall be considered for measurements etc. complete all as per specification, drawing and directions. (Basic Price @ Rs 47,000/ MT)

Supplying, Fabricating and fixing structural steel fabrication works purlins/girders,columns etc., for any structural or architectural feature either outside or inside the building, made of items/sections (sectional details as per drawing) like MS angle, MS plate, MS flat, Z sections, ISMB, ISMC, etc, welding, cutting, grouting in Cement mortar/cement concrete, applying one coat of anti corrosive paint for all the steel surface, etc. complete all as per specification, drawing and direction.(Basic Price @ Rs.55,000/ MT)

Item same as above but using hollow - box section / tubular section, S.H.S / R.H.S etc;(Basic Price @ Rs 60,000/ MT)

Page: 11/24


69 J10 Sqm

70 J12 Sqm

71 J14 Sqm

72 J17 MT

K MISCELLANEOUS WORKS

Providing and fixing MS Railing made of MS Flats as verticals,MS square bars as horizontals,50x50mm MS hollow box sections for hand rail fixed to MS flats as shown in the drawing,including cutting,welding,grinding,grouting/fixing in the floor/masonry/concrete surface,making good the surface at the point of fixing and finishing smooth,applying two or more coats of approved color and shade synthetic enamel paint over a coat of anti corrosive paint for all the steel surface etc complete all as per the specification,drawing and direction. To note that all flats/square & round bars shall be bright bars. Weight of steel sections shall not exceeding 1.8 Kgs/Sft.

Providing, fabricating and fixing in position M.S. Gate made of 50x50 MS box sections frame, 40x10mm flats, 12mm dia rods, fixed to the masonry / RCC member using appropriate approved means, with the other sections such as MS angle, MS square bars, etc, including cutting, welding, grinding, providing hinges, handles, locking arrangements, applying two or more coats of approved color & shade synthetic enamel paint over a coat of anti corrosive paint for all the steel surface, waxing, etc complete all as per specification, drawing and direction. To note that all flats/square & round bars shall be bright bars (The weight of the gate shall be not exceeding 2.00 Kg per Sq ft.)

Supplying and Fixing of M.S window grills in position in the masonry using MS anchors bolts, the grill shall be made of 25x6mm & 40x10mm MS flats, 12mm dia bright bars, including scaffolding, two coats of synthetic enamel paint over a coat of anti corrosive paint for all steel surfaces, to note that all flats/square & round bars shall be bright bars, etc complete all as per specification, drawing and directions. (Weight not exceeding 1.75 kg / SFT).

Providing and fixing/placing in position of MS inserts like expansion/anchor bolt,pin rods or any such items while concreting,welding if required to be held in position,including all lead and lift,scaffolding etc. complete all as per the drawing,specification and directions.

Page: 12/24


73 K1 Sqm

74 New MT

TOTAL FOR CIVIL WORKS Rs.

NOTE: a) The Conditions of Contract as per Civil works - Contract document holds good.b) The item rates and specifications shall be as per BOQ specifications and rates

Providing and fixing of 20mm thick mirror polished approved quality and shade black granite slab in hand wash basin counter,fixed/supported over 50x50mm MS 'T' supports,including providing a cut out of the required size to house the hand wash basin,chasing of the walls if required to house the granite slab,making good of chasing,treating the exposed edges as in the drawing,etc,complete all as per the specifications,drawing and directions.(Granite basic price @ Rs.120/Sft)

Providing and painting steel surface with two coats of synthetics enamel paint Asian / Nerolac or approved equivalent over a coat of primer(Zinc chromite) after scrapping the surface using sand paper, cleaning etc to a required finish all as per specifications, drawing and directions.

c) The items which is not falling under BOQ specifications will be treated as Non-tender items with supporting rate analysis submitted by Vendor and approval from PMC/PGI

Page: 13/24

PROPOSED " M/s PRESIDENCY UNIVERSITY B SCHOOL - ENTRANCE PORCH " AT DIBBUR, BANGALOREENTRANCE GATE AND PORCH

Quantity Rate REMARKS

75 163 12,225.00

Rate Only 245 -

Rate Only 5,098 -

265 347 91,955.00

Rate Only 1,530 -

Rate Only 6,117 -

50 214 10,700.00

Amount

Page: 14/24

Quantity Rate REMARKSAmount

15 2,498 37,470.00

Qty 178 -

25 4,404 110,100.00

5 8,503 42,515.00

25 714 17,850.00

Page: 15/24


40 4,221 168,840.00

220 1,121 246,620.00

15 1,030 15,450.00

10 938 9,380.00

Page: 16/24


Rate Only 6,403 - Qty should be in RMC & 30 6,912 207,360.00

Rate Only 10,837 - rate only for in-situ5 11,144 55,720.00

Rate Only 11,653 - 15 11,878 178,170.00

Rate Only 10,837 - 10 11,144 111,440.00

Rate Only 10,399 - 25 10,664 266,600.00

Rate Only 11,755 -

15 11,755 176,325.00 Rate Only 6,219 -

20 6,403 128,060.00

Rate Only 9,838 -

Rate Only 10,155 - Rate Only 11,755 -

Page: 17/24


15 11,929 178,935.00 5 11,113 55,565.00

Rate Only 13,764 - Rate Only 9,838 -

Rate Only 714 -

140 265 37,100.00

Rate Only 535 - Rate Only 1,071 -

450 408 183,600.00

80 179,440.00

65 230 14,950.00

2930 (2243/-)

Page: 18/24


15 1,784 26,760.00

50 1,500 75,000.00

70 979 68,530.00

Rate Only 488 -

Page: 19/24


20 714 14,280.00

10 4,588 45,880.00

70 561 39,270.00

75 423 31,725.00

100 423 42,300.00

Rate Only 566 -

580 280 162,400.00

Page: 20/24


75 11,475.00

100 153 15,300.00

Rate Only - Rs. 459 + Rs. 153=Rs. 612

109 179 19,511.00

Rate Only 387 -

540 1,122 605,880.00

133 (153/-)

459+153 (459/-)

Page: 21/24


Rate Only 8,666 -

5 8,666 43,330.00

25 -

Page: 22/24


5 -

20 64,739 1,294,780.00

2 127,438 254,876.00

30 139,672 4,190,160.00

Page: 23/24


24 2,345 56,280.00

60 2,753 165,180.00

25 2,345 58,625.00

1 127,438 127,438.00

Page: 24/24


5 3,008 15,040.00

32 -

###

a) The Conditions of Contract as per Civil works - Contract document holds good.b) The item rates and specifications shall be as per BOQ specifications and ratesc) The items which is not falling under BOQ specifications will be treated as Non-tender items with supporting rate analysis

Sheet1

Documents

Entrance Gate and Porch_boq