EngineerSKO Sm

800-295- 9595

* All prices subject to change based upon addition of new components. Components may be substituted due to availability. Items may not be shown individual.

www.kippertool.com

Table of ContentsCarpenter’s Squad Tool KitP/N KIT 5300-R NSN 5180-01-447-2200

Carpenter’s Platoon Tool KitP/N KIT 6000-R NSN 5180-01-447-2199

Cordless 18V Power Tool KitP/N KIT CDSK-WA NSN 5180-01-436-8531

36V Power Tool KitP/N KIT CDSK-36 NSN 5180-01-544-2102

Complete Woodworking Tool KitP/N KIT TMSEWWBM-3KT-R NSN 5180-01-441-2123

Multi-Saw & Drill Tool KitP/N KIT MCRCSDS-39TK-R NSN 5180-01-441-2125

Table Saw & Router Tool KitP/N KIT TSRJS-19TK-R NSN 5180-01-441-2122

Pneumatic Nailer & Compressor KitP/N KIT PNC-34TK-R NSN 5180-01-441-2124

Electrician’s Tool KitP/N KIT ELS1000-R NSN 5180-01-461-8105

Plumber’s Tool KitP/N KIT PLU1000-R NSN 5180-01-467-4676

Pipefitter’s Tool Kit (1/8” to 2”)P/N KIT PLS1000-RNSN 5180-01-461-8108

Pipefitter’s Tool Kit (2 1/4” to 4”)P/N KIT PLP1000-R NSN 5180-01-461-8107

Pioneer Land Clearing & Building ErectionP/N KIT PIO1002 NSN 5180-01-467-4685

Pioneer General Labor Tool KitP/N KIT PIO1004 NSN 5180-01-467-4684

Pioneer Manual Labor Tool KitP/N KIT PIO1003 / PIO1003-TNSN 5180-01-467-4677 / 5180-01-467-4679

Mason & Concrete Finishers Tool KitP/N KIT MAS1000-R NSN 5180-01-461-8110

Lighting KitP/N KIT KTC-LTG-1800 NSN 5180-01-587-7804

18V Impact Tool KitP/N KIT IMPACT TOOL-18VNSN 5180-01-587-8007

36V Impact Tool KitP/N KIT IMPACT TOOL-36V NSN 5180-01-587-8009

18V Metal Working KitP/N KIT METAL WORKING-18V NSN 5180-01-587-8006

Lineman’s Pole Climbing KitP/N KIT LPCNSN 5180-01-587-8026

Pioneer Bobcat KitP/N KIT PIO-BOBCATNSN 5180-01-590-6540

35 36 37 38 39 40 41 42 43 44 45

24 25 26 27 28 29 30 31 32 33 34

800-295- 9595


www.kippertool.com

ATTENTION: PLEASE REVIEW THIS STATEMENT FOR SETS, KITS & OUTFITS

The Engineer Division of the Directorate of Combat Development, USA MANSCEN is responsible for developing and reviewing sets, kits and outfits. The tool sets listed below were reviewed with the intent to modernize them in response to that charter. So as not to impose a burden on the unit commander responsible for procuring the sets, it was decided to utilize a new NSN, allowing the commander to upgrade the unit’s capabilities as funds became available.

Kipper Tool Company (KTC) developed the tool sets to meet those requirements and obtained the NSNs. KTC markets the modernized tool sets through GSA as VMTS. They are made available to units at a time when the pace of unit deployments has accelerated and are showing that the utilization of the state-of-the-art tools speed mission accomplishment.

However, at the present time, regulatory guidance prevents the KTC configuration from being listed in FEDLOG as a substitute for the Line Item Number. DCD-EN, MANSCEN is working to correct the LIN - NSN disconnect. But until it does, units that are purchasing the modernized sets are retaining them by creating a non-standard LIN and using a memorandum signed by the appropriate commander stating that the “new” set is the equal/or better of the LIN being replaced.

LIN Old NSN New (KTC) NSN W34648 5180-00-293-2875 5180-01-447-2200 W34511 5180-00-293-2873 5180-01-447-2199 T16988 3320-00-270-8630 5180-01-441-2123 (Replaces Tool Load Only - Retain Trailer & Generator) W36977 5180-00-313-3045 5180-01-461-8105 W44923 5180-00-596-1504 5180-01-461-8110 W49033 5180-00-545-8647 5180-01-467-4676 W48622 5180-00-596-1501 5180-01-461-8108 W48759 5180-00-596-1509 5180-01-461-8107 W48348 5180-00-596-1546 5180-01-467-4685 W48211 5180-00-596-1537 5180-01-467-4684 W48074 5180-00-596-1539 5180-01-467-4677 W43974 5180-00-408-1350 5180-01-587-8026

INDUSTRIAL SETS & TOOL KITS

SKO Name SKO NSN Replenishment Kit NSNCarpenter’s Squad Tool Kit 5180-01-447-2200 5180-01-513-7684Carpenter’s Platoon Tool Kit 5180-01-447-2199 5180-01-513-7680Cordless 18 Volt Power Tool Kit 5180-01-436-8531 5180-01-513-7689Complete Woodworking Kit 5180-01-441-2123 5180-01-513-7692Table Saw & Router Tool Kit 5180-01-441-2122 5180-01-513-7696Multi-Saw & Drill Tool Kit 5180-01-441-2125 5180-01-513-7703Electrician’s Tool Kit 5180-01-461-8105 5180-01-514-1430Pneumatic Nailer & Compressor Kit 5180-01-441-2124 5180-01-513-7706

If you have one of the new Engineer Tool Systems, a Replenishment Kit for each has been completed and assigned National Stock Numbers. Listed below will match up your SKO NSN with it’s Replenishment Kit NSN. Each Replenishment Kit corresponds with each tool, container, fit, form and function of it’s parent SKO. This will eliminate hours of research and erroneous ordering.

35 36 37 38 39 40 41 42 43 44 45

24 25 26 27 28 29 30 31 32 33 34


800-295- 9595 www.kippertool.com

CARPENTER’S SQUA

DTOOL KIT

CARPENTER’S SQUAD TOOL KIT

Weight: 198 LBS. - Cubic Feet: 23.3

KIT 5300-RNSN 5180-01-447-2200



CARP

ENTE

R’S

PLAT

OON

TOOL

KIT

CARPENTER’S PLATOON TOOL KIT


KIT 6000-RNSN 5180-01-447-2199



CORDLESS 18VOLT INT’LPOW

ER TOOL KIT

CORDLESS 18 VOLT INT’L POWER TOOL KIT


KIT CDSK-WANSN 5180-01-436-8531



36 V

OLT

INT’

L PO

WER

TOOL

KIT

KIT CDSK-36NSN 5180-01-544-2102


36 VOLT INT’L POWER TOOL KIT

DEW DC509

DEW DC901KL DEW DC305K

DEW DC300K

DEW DC300K NSN: 5130-01-588-1536 Heavy-Duty 36VCordless 7 1/4” Circular Saw Kit

• 7 1/4” carbide tipped blade for increased cutting capacity• All metal keyless blade change system• 0-50° bevel capacity with lever-action detnets at 22.5° and 45°• High strength magnesium shoe & upper guard

DEW DC901KL NSN: 5130-01-588-1550 Heavy-Duty 1/2” 36VCordlessHammerdrill/Drill/Driver Kit

• 36V high performance battery pack• Patented 3 speed all metal transmission• Heavy duty 1/2” self-tightening chuck• Anti-slip comfort grip

DEW DC305K NSN: 5130-01-588-1537 Heavy-Duty 36VCordless Reciprocating Saw Kit

• 1 1/8” stroke length and 0-3,000 spm• 4 postion keyless blade clamp• Anti-slip comfort grip for better control• 3 postion adjustable shoe for adjusting depth of cut• 36V high performance battery pack

DEW DC509 NSN: 6230-01-588-1232 Heavy-Duty 36VCordless Floodlight

• Flex-neck design with lockable head clips• Wide angle beam of light• 8 hours run-time on 1 charge• Xenon bulb



WOODW

ORKINGTOOL KIT


KIT TMSEWWBM-3KT-RNSN 5180-01-441-2123

WOODWORKING TOOL KIT



MUL

TI-S

AW &

DRI

LLTO

OL K

IT

MULTI-SAW & DRILL TOOL KIT


KIT MCRCSDS-39TK-RNSN 5180-01-441-2125



TABLE SAW

&

ROUTER TOOL KIT

KIT TSRJS-19TK-RNSN 5180-01-442-2122

TABLE SAW & ROUTER TOOL KIT

Weight: 276 LBS. - Cubic Feet: 35



PNEU

MAT

IC N

AIL

ERS

&CO

MPR

ESSO

R TO

OL K

ITPNEUMATIC NAILERS & COMPRESSOR TOOL KIT


KIT PNC-34TK-RNSN 5180-01-441-2124



ELECTRICIAN’S

TOOL KIT

ELECTRICIAN’S TOOL KIT


KIT ELS1000-RNSN 5180-01-461-8105



PLUM

BER’

STO

OL K

IT

PLUMBER’S TOOL KIT


KIT PLU1000-RNSN 5180-01-467-4676



PIPEFITTER’S TOOL KIT1/8” TO 2” DIA

. PIPE

PIPEFITTERS TOOL KIT 1/8" TO 2" DIA. PIPE


KIT PLS1000-RNSN 5180-01-461-8108

Field Office Site BoxCubic Feet: 192 - Weight: 713



PIPE

FITT

ER’S

TOO

L KI

T2-

1/4”

TO

4” D

IA. P

IPE

PIPEFITTER’S TOOL KIT 2-1/4" TO 4" DIA. PIPE


KIT PLP1000-RNSN 5180-01-461-8107



PIONEER LAND CLEA

RING &

BUILDING ERECTION

PIONEER LAND CLEARING & BUILDING ERECTION

TOOL KIT


KIT PIO1002NSN 5180-01-467-4685



PION

EER

GENE

RAL

LABO

RTO

OL K

IT

PIONEER GENERAL LABOR TOOL KIT


KIT PIO1004NSN 5180-01-467-4684



PIONEER MA

NUAL LA

BORTOOL KIT

PIONEER MANUAL LABOR TOOL KIT

KIT PIO-BOBCAT PACKAGE on page 51

KIT PIO1003 NSN 5180-01-467-4677

w/ KIT PIO-BOBCAT

KIT PIO1003-TNSN 5180-01-467-4679

w/o KIT PIO-BOBCAT



MAS

ON’S

& C

ONCR

ETE

FINI

SHER

’S T

OOL

KITMASON & CONCRETE

FINISHERS TOOL KITKIT MAS1000-R

NSN 5180-01-461-8110



LIGHTING KIT

18V XR+ Battery Packs• 2.4 Amp hour• Quantity 12

Rotating-headlights(Qty. 2)

LIGHTING KIT

24 Volt DC/Nato Slave Plug with 10' pig tail

220 Volt ACwith 10' Pig Tail

12 Volt DC with 10' pig tail

Transport Boxw/ wheels and pressure release valve

(30" x 18" x 20")

110 Volt AC with 10' pig tail

4 Belt PacksEach containing 3 batteries

Provide 3x the life of a single battery

Solar Panels2.5' pig tail (Qty. 2)

18 Volt Cordless FloodlightFlexible neck for hands free operation

Lockable head clip offers versatility & convenienceBattery sold separately

(Qty. 2)

KIT KTC-LTG-1800NSN 5180-01-587-7804

Plug-ins charge 12 batteries at once (solar panel charges one 3-battery bag at a time)

Batteries charge in less than 8 hours, and maintain a full charge while connected to the power source

Automatic shut-off when charge is complete, storage

box may remain closed during charging process

Impact resistant, water-resistant case on

wheels for easy transportation



18 V

OLT

IMPA

CTTO

OL K

IT

18 VOLT IMPACT TOOL KITKIT IMPACT TOOL-18VNSN 5180-01-587-8007


STP 74216 NIIN: 01-590-2059 1/2” Drive 25 pc MetricDeep Socket Set - 6 Point

• 8 mm through 36 mm sockets• (2) 17” socket bar & 25 socket clips

DEW 386445-04 NIIN: 01-590-1998

220V European Plug7.2V - 18V 1 Hour ChargerWith Automatic Tune-Up™ Mode

• Charges all DEWALT® 7.2V - 18V batteries (except Univolt batteries)• Charges the battery in 1 hour or less• The DEWALT 3 stage charging system

STP 7515 NIIN: 01-590-2062 1/2” Drive Locking Impact Extensions

3 pc set consisting of:• 1/2” x 3”• 1/2” x 5”• 1/2” x 10”

DEW DW059K-2 NIIN: 01-590-2006 Heavy-Duty 1/2” 18V Cordless High Torque Impact Wrench Kit

• 300 ft-lbs of maximum torque to perform a wide range of heavy-duty fastening applications• 1,650 rpm/2,600 bpm for faster application speed• Durable magnesium gear case and all metal transmission for extended durability• Heavy-duty impacting mechanism directs torque to fastener without kickback

DEW DW9117 NIIN: 01-590-2013 7.2V-18V 15 Minute Charger

• Charges in 15 minutes or less minimizing charging time • Charges all DEWALT® 7.2V-18V batteries (except Univolt® batteries)• Diagnostics with 2 LED displays has 5 indicators to communicate battery charge status

STP 74116 NIIN: 01-590-2058 1/2”Drive 19 pcDeep Socket Set 6 Point

• 3/8” through 1 - ½”sockets• 17” & 9” socket bar, 19 socket clips

DEW DW9117

DEW DW059K-2

STP 7515

STP 74216

DEW 386445-04

STP 74116



36 VOLT INT’L IMPACT

TOOL KIT

36 VOLT INT’L IMPACT KITKIT IMPACT TOOL-36VNSN 5180-01-587-8009

DEW DC800KL NIIN: 01-590-0879 Heavy-Duty ½” 36V Cordless Impact Wrench Kit

• DEWALT® built high power, high efficiency motor• Patented all-metal anvil for durability• Anti-slip comfort grip for comfort and control• High speed all-metal transmission delivers 1,400 rpm

STP 7515 NIIN: 01-590-2062 1/2” Drive Locking Impact Extensions

3 pc set consisting of:• ½” x 3”• ½” x 5”• ½” x 10”

STP 74116 NIIN: 01-590-2058 ½” Drive 19 pc Deep Socket Set - 6 point

• 3/8” through 1 - ½”sockets• 17” & 9” socket bar• 19 socket clips

EXP VC500W NIIN: 01-588-1551 Step Up Step Down Converter

• Converts electricity from 220/240 volt to 110/120 volt• Allows you to use 110/120 volt appliances or equipment in 220/240 volt countries• Coverts electricity from 110/120 volt to 220/240 volt• Allows you to use 220/240 volt appliances or equipment in 110/120 volt countries

HDG IM2720 NIIN: 01-590-2020 Stormcase with Foam• Length 22” x width 17” x height 10”• Tough, rugged and lightweight• Airtight, watertight, impervious to mother nature• Dent-resistant, shatter-resistant, virtually unbreakable

CWC D18030025 NIIN: 01-590-0879 25’ Extension Cord • 3 way GFI inline

STP 74216 NIIN: 01-590-2059 ½” Drive 25 pc MetricDeep Socket Set - 6 point

• 8 mm through 36 mm sockets• (2) 17” socket bar & 25 socket clips

DEW DC800KL

CEN D18025025 EXP VC500W

STP 7515

HDG LM2720 (Custom cut foam for rapid inventory)

STP 74216 STP 74116



18 V

OLT

MET

AL

WOR

KING

TOO

L KI

T18 VOLT METAL WORKING KITKIT METAL WORKING-18V

NSN 5180-01-587-8006

DEW DW4522 General Purpose Metal Cutting Wheel • 4 1/2" x 1/8" x 5/8"-11

DEW DW8999/DEW DW8900 NIIN: 01-590-6837 Left Blade/Right Blade • Replacement for DC490KA

AEA 40651 NIIN: 01-589-8890 Safety Goggles• Anti-Fog, 0.060” thick• Clear poly lens• Quantity 10

DEW DC490KA Step Up Step Down Converter

• Head swivels 360°• Cuts 7/32” strip which provide consistent & accurate cuts

DEW DC410KA Cordless Cut-Off Tool• 6,500 rpm provides high power for cutting & grinding• 3 position side handle offers greater comfort & control• Metal gear case dissipates heat for longer bearing, gear & motor life

DEW 386445-04 NIIN: 01-590-1998 220 Battery Charger • Charges battery in 1 hour or less• 3-stage charging system

DEW DW934K-2Heavy-Duty 6 3/4” 18VCordless Metal Cutting Circular Saw Kit

• 6 3/4” 40 tooth carbide tipped blade• Multi-coated SIGHT-LINE™ window• ULTRA SIGHT-LINE™ scope allows maximum visibility

CWC 18030025 NIIN: 01-590-0879 25’ Extension Cord • 3 way GFI inline

DEW DW8901 Center Blade • Replacement for DC490KA

DEW DW4523General Purpose Metal Grinding Wheel • 4 1/2” x 1/8” x 5/8”-11

DEW DW4522 DEW DW4523

DEW DW934K-2DEW DC490KA

DEW DC410KA DEW 386445-04

AEA 40651 CWC 18030025

DEW DW8999/DEW DW8900

DEW DW8901



LINEMA

N’S POLE CLIM

BING TOOL KIT

KIT LPCNSN 5180-01-587-8026

LINEMAN’S POLE CLIMBING KIT

Not All Items Are Listed

KLE J2000-9NE NIIN: 01-592-0971 9” High-Leverage Side-Cutting Pliers• Ultra-durable “2000 Series” cutting knives• Plastic dipped handles• Crimping die behind hinge

KLE D502-10-INS Insulated Pump Pliers• 10” length x 1 3/4” max. capacity• Series of channels provides wide range of jaw openings

CRE 130010 Gas & Burner Pliers • 10” length

KLE 3146 Lineman’s Wrench • Large end has 1 3/32” & 29/32” openings• Small end has 13/16” & 5/8” opening

KLE 5165 10 - Pocket Tool Pouch• 10” x 10” overall size• Leather construction• Riveted and stitched

BUC 497099E NIIN: 01-589-7954 Positioning/Pole Strap • Size: 1 3/4” x 7’• Woven nylon

WLF 1003 NIIN: 01-589-8614 Pole & Tree Climbing Harness • Adjustable extension, neoprene lining• Full support - zero turning force

ESX 2117-24-R648 Tool bag • OD Green

BUC 1993F-23 NIIN: 01-589-7946 Belt Body • Wide back support• Attaches to harness

LUF HD403 Hi line Synthetic Fiber Tapes • Steel case w/extra-heavy vinyl covering• 50’ length, 5/8” width blade size

LWL 51T Triple Square Ratcheting Wrench• Ergonomic handle, reversing control in head• Fluorescent orange sockets• 3 in 1 socket fits: 3/4”, 1” and 1 1/8”

KLE 1570-3 Lineman’s Skinning Knife• 2 1/4” tempered-steel blade• Two layers of insulation• Extra-strong construction for line work

CEM CPIRB-1214/ CEM CPIRB-1618/CEM CPIRB-2024

Ratcheting Box Wrenches• 3/8” x 7/16”• 1/2” x 9/16”• 5/8” x 3/4”

IDL 34-003 Safe-T-Grip Fuse Puller• Puller for 31 to 600A/250V & 400A/600V, 3/4” to 2 1/2” dia.• Fuses 11 3/4” long

KLE HD507-12 12” Adjustable Wrench• 12” length with 1 1/2” capacity• Forged heat-treated alloy steel• High polish chrome finish

KLE J2000-9NE

KLE D502-10-INS

CRE 130010

KLE 3146

KLE 5165

BUC 497099EWLF 1003 ESX 2117-24-R648

BUC 1993F-23

LUF HD403

LWL 51T

KLE 1570-3

CEM CPIRB-1214/1618/2024

IDL 34-003

KLE HD507-12



PIO-

BOBC

ATPA

CKAG

E

KIT PIO-BOBCAT PACKAGENIIN: 01-590-6540

(28 Items included)

S150 Skid Steer LoaderThe new Bobcat® S150 (formerly the 763 skid steer loader) delivers lots of muscle, lift capac-ity and lift height. The powerful Kubota engine produces plenty of traction and breakout force for excavating and handling large loads. There’s also a 16.7 gpm hydraulic pump for efficient at-tachment performance.

The Kubota engine in the S150 is compliant with EPA Standards for Tier II engine emissions.

The improved deluxe cab offers a smooth, comfortable ride, with more headroom, improved visibility, better airflow, easy-to-see-and-use instrument panels and more. A curved roof deflects rainwater to keep the seat dry, while an integrated seat belt system and improved seat bar blend safety with added comfort. Even the

Rated Operating Capacity (SAE): 1500 lbs (680 kg) Tipping Load: 3000 lbs (1361 kg) Travel Speed: 7.3 mph (11.3 kmh) Travel Speed (2-speed option): n/a Pump Capacity: 16.9 GPM (64 L/min) Pump Capacity - High Flow: n/a

Length with Standard Bucket: 130.3 in (3309 mm) Width (with bucket): 68 in (1727 mm) Height: 76.3 in (1938 mm) Height to Bucket Hinge Pin: 114.5 in (2908 mm)

Engine Make: Kubota Engine Model: V2203-M-DI Engine Fuel: Diesel Engine Cooling: Liquid Number of Cylinders: 4 Horsepower (SAE NET): 46 HP (34.3 kW) Displacement: 134 cubic in (2.2 L) Fuel Tank: 14 gal (53 L)

doors have been improved to make it easier to enter and exit the cab.

The G-Series features an all-new instrumentation system to help you keep track of engine and loader functions, control the machine and troubleshoot problems. A panel on the lefthand side displays engine temperature, fuel and the hour meter/code display/glow plug countdown. It also contains switches to control work lights, auxiliary hydraulics modes, auxiliary hydraulics pressure relief and other options, such as bucket positioning and high-flow hydraulics.

The right-hand display panel contains indicator/warning lights and the key switch. An optional Deluxe Instrumentation Panel can be added in place of this right-hand display. The Deluxe panel features keyless start; visual bar graphs that monitor hydraulic oil temperature and pressure, engine oil pressure and battery voltage; a digital tachometer; a digital clock; a job clock and diagnostic information.



PIO-BOBCATPACKAGE

S150 Skid Steer Loader Attachments

MIR M0003NIIN: 01-590-5850Skid Steer, Melroe-BOBCAT Model S-150, Large Operator Seat Bar, Hose Retainer Kit with:

MIR M0003-P01-031NIIN: 01-590-5893Suspension Seat

MIR M0003-R20-C02NIIN: 01-590-5895Catalytic Exhaust Purifier

MIR 7111884NIIN: 01-590-5839Steel Track Package

MIR M0003-R09-C08NIIN: 01-590-5853Heavy Duty 10-16.5 Tires (4)

MIR 7108394NIIN: 01-590-5851Four Point Lift Kit

MIR M0003-R11-C02NIIN: 01-590-5856Hydraulic Bucket Positioning Kit

MIR M0003-A01-C01NIIN: 01-590-5854Attachment Control Kit

MIR 6901726NIIN: 01-590-5846Load Operator Training Kit

MIR 6731937NIIN: 01-590-5841Special Application, Doors

MIR 7101325NIIN: 01-590-5847Mounting Kit

MIR M0003-A02-C05NIIN: 01-590-5857Port Relief Valve

MIR 7167311NIIN: 01-590-5848Bucket, Combination68” Wide w/Teeth

MIR 6712927NIIN: 01-590-5889Frame, pallet Fork, 42” Teeth

MIR 6540183NIIN: 01-590-5879Tines, Pallet Fork, 42” L (2 per set)

MIR 6737322NIIN: 01-590-5842Teeth, Bolt on (8)w

MIR 6809445NIIN: 01-590-5840DrIve, Auger, Model 30

MIR 6812980NIIN: 01-590-5838Frame, Mounting, Auger

MIR 6666893NIIN: 01-590-5880Bit, Auger, 12" Dia



MIR 6679826NIIN: 01-590-5887Extention 24" Adj Round

Auger Bit Attachments c/o:

MIR 6809445NIIN: 01-590-5840Drive, Auger, Model 30

MIR 6812980NIIN: 01-590-5838Frame, Mounting, Auger




MIR 6679826NIIN: 01-590-5887Extention 24" Adj Round

Breaker Attachments c/o:



PIO-

BOBC

ATOP

TION

AL IT

EMS

MIR 6532700Backhoe, Hydraulic, 9' Depth

MIR 6715503Bucket, Backhoe, 24" W, w/Standard Teeth

MIR 7101325Mounting Kit, Backhoe

BACKHOESTurn your Bobcat® Loader into a powerful excavator with a full line of backhoe models for all sizes of Bobcat Loaders. Here’s a part-time attachment that can handle full-time excavation jobs. Maximum digging depths range from 5 to 11 feet. Rear stabilizers are available for certain loader models.

MIR 6536901Broom, Angle, 68" W

ANGLE BROOMSweep a clean path economically. Put your Bobcat® loader to work and clean up almost everything in sight with the hydraulically-driven Angle Broom attachment. Use it to sweep driveways, sidewalks, parking lots, loading docks, warehouses, and more. Excellent for quick snow removal without damaging pavement surfaces.

Optional Separate Items

MIR 6710548Roller, Vibratory, 72" W, w/Padded Drum

VIBRATORY ROLLERThe roller is quick and easy to attach with the exclusive Bob-Tach mounting system. The Bobcat vibratory roller features either a smooth or padded drum. The roller is ideal for flatwork, trenching and asphalt patchwork contractors. For added versatility on the job, a bolt-on smooth outer shell is available for the 48" drum to convert it from a padded drum to a smooth drum.

Also available in od green call for details

Documents

EngineerSKO Sm