ENGINE OILS - Whitepages · ENGINE OILS MF Ultra Engine Oil 15W/40 is ... utmost protection to Tier 4 and Stage ... Massey Ferguson Lubricants Guide Australia - 2. MF Premium Engine

ENGINE OILS

MF Ultra Engine Oil 15W/40 is a low SAPS (Sulphated Ash, Phosphorus and Sulphur) synthetic diesel engine oil. This product has been formulated to provide the utmost protection to Tier 4 and Stage 3B engines, operating in very severe conditions,including temperatures down to -20º C*. MF Ultra Engine Oil 15W/40 has been developed for use in engines filtered with particulate filters (DPFs) or SCR NOX reduction systems. Also suitable for use in units employing exhaust gas recirculation (EGR)* Please seek technical advise for operating temperatures below -20ºC.

Specifications• API C J-4 / SM • ACEA E9 - 08 • CAT ECF-3 • Cummins CES 20081 • MAN M3275 • Mack EO-O Premium Plus • DDC PGOS 93 IT 218 • EMA DHD-1 • Mercedes Benz 228.31 • Volvo VDS-4 • Renault VI RDL-3 Compliance

3933543M1 20L 3933544M1 205L

MF Ultra Engine Oil 15W/40

Massey Ferguson Lubricants Guide Australia - 2

MF Premium Engine Oil 15W40 is a mineral based advanced technology heavy-duty diesel engine oil designed to meet the most severe lubrication requirements of European heavy-duty diesel clean fuels engines fitted on MF equipment – meeting the latest CI4 specification requirement.

Specifications• API C I-4 • ACEA E4/E7-08 • MB 228.5 • Volvo VDS-3 • Global DHD-1• MAN M3277 • MTU DDC Type 3 • Mack EO-M+ • Cummins CES 20077/78 • Renault Trucks RXD/RLD-2 • M1109 & M1140

* 5L Fully imported at 10W/40 ** 205L AGCO branded

3933304M1 5L* 3496650M1 20L 3496661M1 205L**

MF Premium Engine Oil 15W/40

MF Heritage Engine Oil provides unrivalled value for a large variety of older MF tractors and can be used in a broad range of applications. MF Heritage Engine Oil is a mineral based oil with proven performance in combating sludge build-up and component wear to give long life performance at an economical operating cost.

Specifications • SAE 15W-40 • M1109 • M1140 • API CH-4 • Tier 2 • ACEA E5 A3 B4-08 • Cummins CES 20071/20072/20076 • Allison C4

3496912M1 20L 3496913M1 205L

MF Heritage Engine Oil 15W/40


UNIVERSAL OIL

This Universal lubricant is designed for a multitude of uses. Recommended for older MF Tier II, this product has a wide range of applications in the industry. It is recommended for use in engines, final drives, hydraulic systems, wet brake and immersed clutches where a 20W/40 universal oil is required.

Specifications• MF M1144, M1139, M1135 • API CE/SG (Tier 2) • API GL4 (SAE 80W/90) • MIL-L-2104D • MIL-L-2105D • MAN 271 • Ford M2C-121B/159B134D • JD J27, J20C • Allison C4 • Cat TO-2 • NH 410B • ZF TE-ML 06C, 07B

* 5L Fully imported at 10W/30

3931033M3 5L* 3496654M1 20L 3496655M1 205L

MF Universal Oil 20W/40

TRANSMISSION OILS

Meeting the MF specification for latest production machines (M1145), Power HC Plus is a synthetic high performance oil with superb transmission friction properties. Ideal for use in transmissions, hydraulic systems final drives, wet brakes and immersed clutches.

Specifications• MF M-1145, M-1139, M-1144, M-1135 • API CG-4 • MIL-L-2104D • Ford M2C-121B, 134D, 159B • Allison C4 • John Deere JDM J27, J20C • MB 228.1 • New Holland NH 410-B • ZF TE-ML 06C, 07B • API GL4 • Caterpillar TO-2

3933334M1 5L 3933058M2 20L 3933056M2 205L

MF Power HC Plus Transmission Oil 10W/40

AGCO Transmission Oil is a superior, multipurpose, wet brake transmission/hydraulic fluid Formulated specially to AGCO requirements. Designed for Heavyweight anti-squawk Tractor Transmissions. It provides exceptional levels of gear wear protection throughout the service period. Ideally suited to all older AGCO machinery including MF, Challenger, Valtra, Iseki and Fendt equipment.

Specifications• API GL4 • M1143, M1144, M1139 • SAE 20W40 John Deere J20A/C • Allison C4 • Caterpillar TO-2 • Ford ESN-M2C134-A/B/C/D • Ford ESEN-M2C86-A/B • New Holland NH – 410B • Volvo (WB101)

* 205L Massey Ferguson Branded

VACC3346 5L 3496662M1 20L 3496655M1 205L*

AGCO Branded

AGCO Transmission Oil 20W/40


Specifically designed for use in limited slip differentials - this is a hypoid transmission fluid with LS additive. Includes a high level of extreme pressure additives to protect critical mechanisms in limited slip differentials.

Specifications• API GL-5+ • MIL-L-2105D

FX991500221 20L

FENDT Branded

Super Trans LS 85W/90

AGCO Super Gear 85W140 is designed for use in hypoid, bevel and spiral gear units, axles and final drives operating under severe conditions and over a wide spectrum of operating temperatures. Through its multigrade viscosity characteristics, AGCO Super Gear is also suitable for MF rear axle applications and can be used as an alternative where a 90W140 is specified in some earlier MF operator’s manuals.• Provides effective wear protection even under severe load conditions ensuring longer component life• High safety margin against foaming and corrosion• Superior viscosity/temperature and cold flow properties• Compatible with all seal materials applied.

Specifications• Allison C3/C4 • API GL-5 • ZF TE-ML 05A/16D/19B • M1134 • GM Dexron® II D • GM Type A Suffix A • MB 236.1/.2/.3 • ZF TE-ML03/04/11/14/17 • Ford Mercon®, ESP-M2C138-CJ, 166-H

VACC3045 5L VACC3044 20L

AGCO Branded

AGCO Super Gear Oil 85W/140GEAR OILS

Synthetic Reaction Arm Fluid SAE 50 is a high performance specialised high performance product designed to ensure optimised operational efficiency in highly loaded off-highway transmissions and gear sets. The synthetic formulation will cope with high temperatures, control oxidation and remain stable over a wide variety of operating conditions. The product is ideally suited to use in reaction arm bearings (drive wheel hubs), mid-roller wheel hubs and idler wheel hubs of Challenger MT700 A, B & C and MT800B A, B & C Series.

Specifications• Caterpillar TO-4 • Allison C-4

79034867W 3.78L

AGCO Branded

AGCO Synthetic Reaction Arm Oil SAE 50

HYDRAULIC OIL

This is a high performance, mineral oil based VHS (Very High Shear) hydraulic fluid which possesses a viscosity index higher than 150. It provides excellent cold start fluidity at low temperatures, preventing the occurrence of pump cultivation, as well as maintaining good oil film thickness at high working temperatures. AGCO VHS Hydraulic 68 also allows for rationalization possibilities as it can replace standard ISO 46 hydraulic oils. It contains wear, oxidation and corrosion inhibitors. Specifically suited to Massey Ferguson and Gleaner combines.

Specifications• DIN 51524 Part 3 (HVLP) • M 1116• Sperry Vickers I-286-S3, M-2950-S • Cincinnati Milacron P-68, P-69, P-70 • Denison HF-0 dry and wet T6C-020• Denison HF-1, HF-2 • Poclain (HV46) • CETOP RP91H • AFNOR E48-603 (HV:HM) • ASLE 64.1 to 64.4, 70.1 to 70.3

3496664M1 20L

AGCO Branded

AGCO Very High Sheer Hydraulic Oil 68


AGCO General Purpose Hydraulic Oil ISO 46 is mineral based hydraulic oil with good anti-wear properties, providing protection in the most demanding of systems. It is rust, corrosion and oxidation inhibited and contains an effective anti-foam additive to control foam and facilitate the rapid release of entrained air, therefore maximizing hydraulic system efficiency. They are miscible and fully compatible with all mineral hydraulic oils.

Specifications• DIN 51524 Parts 1 and 2 (DIN 51525) • Sperry Vickers I-286-S, M-2950-S • Denison HF-2 • Cincinnati Milacron P-68, P-69, P-70

3496658M1 20L 3496659M1 205L

AGCO Branded

AGCO General Purpose Hydraulic Oil 46

Designed for use in bevel, spiral gear units, axles and final drives operating under severe conditions and over a wide spectrum of operating temperatures. Incorporates superior viscosity and cold flow properties.

Specifications• API GL5 • ZF TE-ML 05A/16B/17B/19B • M1134

VACC3374 5L 3496668M1 20L

AGCO Branded

AGCO Gear Oil 80W/90


Pentosin CHF 11S is a synthetic high performance hydraulic fluid for life-time application in modern vehicle aggregates. Pentosin CHF 11S is especially designed for hydraulics in the automotive industry with the highest technical requirements such as in: power steering, level control, shock absorber, hydro-pneumatic suspension, stability and traction control, hydraulics for convertible tops, central lock systems, etc. It is suitable for all extreme conditions and guarantees full performance from -40°C to over 130°C system temperature.

Specifications• DIN 51 524T3 and ISO 7308

X902011622000 1L

Pentosin CHS 11S Hyd Clutch Synthetic Oil

GREASES

AGCO High Performance Extreme Pressure Lithium Grease is AGCO Engineer approved premium “extreme pressure” multipurpose lithium grease. Timken approved for all bearing applications. Proven in the field & ideal for tractors, combines, construction & truck applications for extended periods under extreme load, temperature & weather conditions.

Specifications• NLGI 11 • Extreme pressure Lithium grease • Timken approved

3496391M1 450g

AGCO Branded

AGCO EP Lithium Grease 450 g

Formulated specifically for use in hydraulic braking systems designed to use a mineral oil based fluid. Warning: Suitable for use only in hydraulic systems using a green mineral oil. Please ensure you check the operator’s instruction book for details of use. Never use this fluid in any reservoirs painted black. Not to be used in vehicles using vegetable based fluid or synthetic brake fluids.

Specifications• ISO 7308 • PSA B71 2710 • Ford ESN M6C 59A

3405389M2 1L

LHM Mineral Brake Fluid


AGCO Coolant is a Ready to use 50/50 premix of Universal coolant for European, US & Japanese heavy duty diesel engines. It is specifically designed to service the requirements of AGCO agricultural machinery & a broad range of heavy duty diesel engines. AGCO Coolant provides outstanding protection against rust and corrosion for all parts of the cooling system and is recommended for all year round use. Not suitable for Fendt tractors – refer Fendt Extra NF Coolant

Specifications• Ethylene Glycol based coolant meets the technical requirements of BS6580:1992

VACC3401 5L 3496666M1 20L

AGCO Branded

AGCO Coolant

AGCO Lithium 11 Grease is AGCO US Engineer approved Lithium 11 “extreme pressure” multipurpose grease. Specifically designed for AGCO’s North American combine & baler equipment, it is Timken approved for all bearing applications. Proven in the field for extended periods under extreme load, temperature & weather conditions.

Specifications• NLGI 11 • Extreme pressure Lithium 11 grease • Timken approved

79014728W 400g

AGCO Branded

AGCO Lithium 11 Grease (North American Pack) 400g

COOLANT

Engine OilsAGCO Ultra Engine CJ4 15W/40 205L 3496834M1AGCO VS Plus 15W/40 205L 3496677M1AGCO Premium Engine 15/40W 1000L 3496842M1Universal OilsAGCO Super Farm Universal 205L 3496678M1 Transmission OilsAGCO Super Versitrac 10W/40 205L 3496803M1AGCO Limited Slip XEP 90 205L 3496682M1AGCO Liquimatic JDF Transmission 205L 3496679M1AGCO Transmission 1000L 3496843M1AGCO Ultra Power Trans 1000L 3496789M1Hydraulic OilsAGCO Triad Hydraulic 46 205L 3496852M1 AGCO Triad Hydraulic 68 205L 3496853M1Gear OilsAGCO EP Gear 80W/90 205L 3496680M1AGCO EP Gear 85W/140 205L 3496681M1CoolantAGCO Antifreeze (not suitable for Fendt) 205L 3496683M1

AGCO Branded Bulk OilsWORKSHOP OILS


TECHNICAL INFORMATION

SAE CLASSIFICATIONSociety of Automotive Engineers

ISO CLASSIFICATIONInternational Standards Organization

Viscosity Classification and Multigrades


Pollution And Emission Legislation


Exhaust Technologies


Performance Classifications


ACEA Performance Classifications

ACEA ‘E’ SequencesE4: Stable, stay-in-grade oil providing excellent control of piston cleanliness, wear, soot handling and lubricant stability.

Suitable for: On-road: Euro 1, 2, 3 and Euro 4 engines Off-road: Tier 1 / Stage I, Tier 2 / Stage II, Tier 3 / Stage lilA, I nterim Tier 4 / Stage III B

Itissuitableforengineswithoutparticulatefilters,andforsomeEGRenginesandsomeenginesfittedwith SCRNOxreductionsystems. Product: Claas lJltra Plus 10W/40

E6: Low SAPS - Stable stay in grade oil providing excellent control of: Piston Cleanliness, Wear, Soot handling.

Suitable for: On-road: Euro 1, 2, 3, 4 and Euro 5 engines Off-road: Tier 4 Candidate SuitableforEGRengineswithorwithoutDPFandforenginesfittedwithSCRNOxreductionsystems.

E6stronglyrecommendedforengineswithDPFandisdesignedforuseincombinationwithlowsulphur (50ppm max) diesel fuel. E7: Stable stay in grade oil providing excellent control of: piston cleanliness, bore polishing, wear, turbo deposit control, soot handling. Suitable for: On-road: Euro 1, 2, 3 and Euro 4 engines Off-road: Tier 1 / Stage I, Tier 2 / Stage II, Tier 3 / Stage IIIA, Interim Tier 4 / Stage IIIB SuitableforengineswithoutDPFandformostEGRenginesandmostenginesfittedwithSCR NOxreductionsystems. E9: Mid SAPS - Stable stay in grade oil providing excellent control of: PistonCleanliness,Wear,Soothandling.MidDrain.

Suitable for: On-road: Euro 6 baseline performance Off-road: Tier 4 Candidate

SuitableforEGRengineswithorwithoutDPFandforenginesfittedwithSCRNOxreductionsystems. E6stronglyrecommendedforengineswithDPFandisdesignedforuseincombinationwithlowsulphur (50ppm max) diesel fuel.


Performance Classifications - European Specs


Performance Classifications

Oil Storage General Advice


©AGCOLimited2012LatestEdition-May2012AGCOPartsprovidesworldwidegenuinesupporttoallAGCOmachinerybrands

Documents

ENGINE OILS - Whitepages · ENGINE OILS MF Ultra Engine Oil 15W/40 is ... utmost protection to Tier 4 and Stage ... Massey Ferguson Lubricants Guide Australia - 2. MF Premium Engine