POWER MEASUREMENT MODULEMODEL NO: DL 10060

ILLUSTRATION

TOQUE-SPEED MEASUREMENT MODULEMODEL NO: DL 200DC

ILLUSTRATION

SPECIFICATION:

DC voltage: 50 V (10 mV/V)DC current: 9.99 A (250 mV/A) AC voltage: 60 V (10 mV/V) AC current: 9.99 A (250 mV/A) AC Power: 999 W (1 mV/W)Power supply: 220 V, 50/60Hz

SPECIFICATION:

Power Supply: 220V, 50/60 HZDigital read out and analog output proportional to the measured value.

FUNCTION/PURPOSE:- For For dc voltage and current

measurement through a voltmeter and an ammeter.

- For ac voltage, current and power measurement in single or three-phase systems; consisting of a voltmeter and an ammeter, switchable on different phases without interrupting the circuit, and of a two-system wattmeter (Aron insertion)

FUNCTION/PURPOSE:- Suitable for measuring the motor output torque

through the load cell arranged on brake unit.

POWER SUPPLY MODULEMODEL NO: DL 10016

ILLUSTRATION

LOAD RHESTAT/STARTING RESISTOR MODULEMODEL NO:DL 10200RHD

ILLUSTRATION

SPECIFICATION:Output voltages Variable ac: 3 x 0 46V,‐ 10A 3 x 0 26V,‐ 14A Standard fixed ac: 220V, 10A Variable dc: 0 46V,‐ 14A 0 32V,‐ 14A 0 42V,‐ 5A

SPECIFICATION:

FUNCTION/PURPOSE:

Suitable for supplying variable alternate and rectified direct current, in order to carry on easily all the test on the electric machinesof the Microlab laboratory and in general in an electric measuring laboratory. Provided with start push button‐ with remote control switch, stop push button,‐ key unlocked emergency mushroom head push button‐ and differential magneto thermal protection on the mains sockets. Connector for overspeed protection of the motors. The control devices and the connecting terminals are arranged on the front panel.

FUNCTION/PURPOSE:

Step-variable rheostat for the half torque starting of the dc motors of the laboratory.

SYNCHRONIZING MODULEMODEL NO: DL 10125

ILLUSTRATION

DATA ACQUISITION MODULEMODEL NO:DL 1893

ILLUSTRATION

SPECIFICATION: SPECIFICATION:

Direct power supply from USB, - Input levels: -10/+10 Vtotal consumption less than 100mA. - High impedance input amplifier:

Nr. 2 relay outputs. > 1MOhm Nr. 2 analogue outputs, with: - A/D converter 12 bit

- Serial D/A converter 8 bit - Self calibration and self zeroing - Output levels: -10/+10 V - Max speed of conversion: 10 kHzNr. 8 analogue inputs, with:

Driver for Windows 98, Me, 2000, and XP

FUNCTION/PURPOSE:

Starting rheostat for the three-phase slip ring induction motors and excitation device for the synchronization of the motor with the mains.

FUNCTION/PURPOSE:

Data acquisition unit with 8 analogue channels. Equipped with 2 relays and 2 analogue outputs. It is possible to acquire continuous signals or slowlyVariable up to 100Hz.

DEAD-WEIGHS FOR TORQUE MEASUREMENTMODEL NO: ____________

ILLUSTRATION

OPTICAL TACHOMETERMODEL NO: DL 2026R

ILLUSTRATION

SPECIFICATION: SPECIFICATION:

Measuring range: 50 to 19,999 rpm.Power supply: 4 x 1.5 V batteries(UM 3), included.Complete with 5 reflectors.

FUNCTION/PURPOSE: FUNCTION/PURPOSE:

Suitable for measuring the revolving speed with digitalReadout

PHASE DETECTORMODEL NO: ____________

ILLUSTRATION

THRE-PHASE RESISTIVE LOADMODEL NO: ____________

ILLUSTRATION

SPECIFICATION SPECIFICATION:

Max. power: 3 x 85 VAr

FUNCTION/PURPOSE FUNCTION/PURPOSE:

Single or three-phase capacitive step-variable load

THREE-PHASE CAPCITIVE LOADMODEL NO: ____________

ILLUSTRATION

FREQUENCY METERMODEL NO: ____________

ILLUSTRATION

SPECIFICATION:

Max power: 3 x 110 W

SPECIFICATION

FUNCTION/PURPOSE:

Single or three-phase resistive step-variable load

FUNCTION/PURPOSE

ELECTRONIC SPEED TRANSDUCERSMODEL NO: ____________

ILLUSTRATION

THERMOCOUPLE (PELTIER)MODEL NO: ____________

ILLUSTRATION

SPECIFICATION SPECIFICATION

FUNCTION/PURPOSE FUNCTION/PURPOSE

SOLAR PV CELL PROTOTYPEMODEL NO: ____________

ILLUSTRATION

SPECIFICATION

FUNCTION/PURPOSE