Embed Size (px)
Citation preview
1000 Top Sheet Cover Width
Brackets Typically @ 1167
166.7
32
Varies - See Table
Varies - See Table
Please Note:
System is fire rated using Knauf Factoryclad 40 ECOSE insulation of minimum thickness 80mm with steel outer sheet only, to achieve 120 minutes Integrity, 15 minutes
(min) Insulation which meets the requirements of Building Regulations Part B for external walls where fire attack is from inside the building and the wall is 1M or more
from the boundary.
System can be fire rated using Rockwool insulation of minimum thickness 120mm with steel outer sheet only, with liner stitched at 300mm centres, to achieve 120
minutes Integrity, 30 minutes (min) Insulation.
Ensure roll edges are lapped/butted to ensure no gaps.
** * *
*
*Fixings with an asterix are required on sheet ends and end laps only.
*
*
Elite System 51
Bracket Height
Insulation
Thickness
Insulation Value
Overall System
Depth
U Value at 1.8M
Centres
120mm
140mm
150mm
160mm
180mm
200mm
220mm
120mm
140mm
150mm*/160mm
160mm
180mm
200mm
220mm
0.040
0.040
0.040
0.040
0.040
0.040
0.040
153mm
173mm
183mm
193mm
213mm
233mm
253mm
0.35
0.30
0.28
0.27
0.24
0.21
0.20
170mm 180mm 0.040 203mm 0.25
240mm
260mm
280mm
0.040
0.040
0.040
273mm
293mm
313mm
300mm 0.040 333mm
* Only available in Rockwool Cladding Roll
240mm
260mm
280mm
300mm
0.18
0.17
0.15
0.14
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
1 of 15
Min 60
ELITE SYSTEM 51 SIDE LAP DETAIL ELITE SYSTEM 51 END LAP DETAIL
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC 32-167-1000
Wall 32_6Rev 0.5mm steel
50mm x 1mm butyl sealing tape
Quattro bar & bracket to required
depth typically @ 1.167m centres
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Quattro bar & bracket
4mm Bead class A
butyl sealant
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
100
COLOUR SIDE
COLOUR SIDE
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel Side lap
Euroclad EC 32-167-1000
Wall 32_6Rev
0.5mm steel Side lap
STANDARD LAP DETAIL STANDARD LAP DETAIL
0.040 Quilt insulation
Please Note:
System is fire rated using Knauf Factoryclad 40 ECOSE insulation of minimum thickness
80mm with steel outer sheet only, to achieve 120 minutes Integrity, 15 minutes (min)
Insulation which meets the requirements of Building Regulations Part B for external walls
where fire attack is from inside the building and the wall is 1M or more from the boundary.
System can be fire rated using Rockwool insulation of minimum thickness 120mm with
steel outer sheet only, with liner stitched at 300mm centres, to achieve 120 minutes
Integrity, 30 minutes (min) Insulation.
Ensure roll edges are lapped/butted to ensure no gaps.
On intermediate supports fixing at each
profile side lap and subsequently in
alternate troughs. Fix all troughs at
sheet ends & end laps
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
2 of 15
23
94
1
2
9
°
73
32
167 2321
3
9
5
3
9
1000
COLOUR SIDE
COLOUR SIDE
COLOUR SIDE
COLOUR SIDE
167167
104
19
R
4
22
2
8
1
3
7
°
1
0
1000
18
EUROCLAD EC 19-167-1000 Liner 19_2L 0.4mm
LINER
EUROCLAD EC 32-167-1000 Wall 32_6Rev 0.5mm
EXTERNAL SHEET
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
3 of 15
40
Brackets less than 260mm require
2 fixings diagonally opposite.
Brackets 260mm or more require
4 fixings.
< 260mm
≥ 260mm
40
33
34
60
59
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
SIDE ELEVATION
Maximum bar cantilever at free
ends is 300mm.
Spigot can fall anywhere between
two brackets.
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
4 of 15
9 x 3mm Class A Butyl Sealant
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Liner flashing sealed to masonry
Class A Butyl Sealant to thickness
required to provide adequate air
sealing to masonry wall.
Quattro Bracket to required
depth typically @ 1167mm centres
Quattro Spacer Rail
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Class A Butyl Sealant to thickness
required to provide adequate air
sealing to masonry wall.
Flashing stitched at max 450mm centres
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
5 of 15
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Quattro Bracket to required
depth typically @ 1167mm centres
Fixings in alternate troughs on intermediate
supports and in all troughs at sheet ends & end laps
9x3mm Mastic Sealant
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Internal Flashing fixed and sealed
to internal elements
9x3mm Mastic Sealant
Door detail by others
External Flashing
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Timber Packer
Sealant
9 x 3mm Class A Butyl Sealant
Flashing stitched at max 450mm centres
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
6 of 15
External flashing
9 x 3mm Class A Butyl Sealant
Quattro Bracket to required
depth typically @ 1167mm centres
Quattro Spacer Rail
9 x 3mm Class A Butyl Sealant
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Quattro Spacer Rail
Internal flashing fixed and sealed
to provide air tightness
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
9x3mm Mastic Sealant
Flashing stitched at max 450mm centres
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
7 of 15
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Drip Flashing
Drainage Point
Quattro Bracket to required
depth typically @ 1167mm centres
Large amount of sealant to make
allowance for imperfection in concrete and
ensure good airtightness. Seal may be achieved
at flashing or structural element such as ring beam,
depending on project specific details.
Internal Flashing and profile filler sealed to liner
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
Profile Filler
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
8 of 15
9 x 3mm Class A Butyl Sealant
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Quattro Bracket to required
depth typically @ 1167mm centres
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Internal flashing fixed and sealed
to provide air tightness
9x3mm Mastic Sealant
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
External Flashing
Stitched at max 450mm centres
9x3mm Mastic Sealant
Quattro Bracket to required
depth typically @ 1m centres
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
9 of 15
Large amount of sealant to make
allowance for imperfection in concrete and
ensure good airtightness. Seal may be achieved
at flashing or structural element such as ring beam,
depending on project specific details.
Closure Flashing
Quattro Bracket to required
depth typically @ 1167mm centres
Closure Flashing fixed and profile filler
sealed to liner to provide air tightness
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Profile Filler
Drip Flashing
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
10 of 15
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Quattro Bracket to required
depth typically @ 1167mm centres
Fixings in alternate troughs on intermediate
supports and in all troughs at sheet ends & end laps
9x3mm Mastic Sealant
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Internal Flashing fixed and sealed
to internal elements
9x3mm Mastic Sealant
Vehicle Access Door Detail by others
External Flashing
Packer by others
Sealant
9 x 3mm Class A Butyl Sealant
Flashing stitched at max 450mm centres
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
11 of 15
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
40
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
Profile Filler
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Sealant
Drip Flashing
Closure Flashing
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Quattro Bracket to required
depth typically @ 1167mm centres
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Packer by others
Vehicle Access Door Detail by others
Internal Flashing fixed and sealed
to internal elements
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
12 of 15
40
Profile Filler
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Window Detail by others
Internal Flashing fixed and sealed
to internal elements
Sealant
Packer by others
Quattro Bracket to required
depth typically @ 1167mm centres
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
13 of 15
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
40
Internal Flashing fixed and sealed
to internal elements
Quattro Bracket to required
depth typically @ 1167mm centres
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Packer by others
Window Detail by others
Profile Filler
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Sealant
Drip Flashing
Closure Flashing
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
14 of 15
Euroclad EC 32-167-1000 Wall 32_6Rev
0.5mm steel
Quattro Bracket to required
depth typically @ 1167mm centres
Fixings in alternate troughs on intermediate
supports and in all troughs at sheet ends & end laps
9x3mm Mastic Sealant
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Internal Flashing fixed and sealed
to internal elements
9x3mm Mastic Sealant
Window detail by others
External Flashing
Timber Packer
Sealant
9 x 3mm Class A Butyl Sealant
Flashing stitched at max 450mm centres
EUROCLAD ELITE SYSTEM 51 WALL CONSTRUCTION
Insulation excluded for clarity
A range of mineral & glass wool insulations are available for different requirements
TITLE: Elite System 51
DWG NO: E51
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
15 of 15
