23-04-19

Electrical contacts

What is an electrical contact?

Why doesn’t it always work?

Lena SjögrenCorrosion and Metals Research Institute

23-04-19 kabels_kurs.swf

Cable connection between two printed circuit board assemblies

An electrical signal between the two boards will be transmitted through six contacts: solder joint (printed circuit board to contact pin) - connector (contact pin to contact spring) - insulation displacement connection (contact spring to cable) - insulation displacement connection - connector - solder joint

23-04-19

23-04-19

Power transmission

Signal transmission

Grounding – personal safety

Signal ground

Electromagnetic shielding

Electrical contacts

23-04-19

Kontaktområde - förstoring

23-04-19

23-04-19

Contact area

Force

H

FA

23-04-19

Current is constricted through the contact spots

The detour required from the current (the electrons) results in an additional voltage drop thus resistance - constriction resistance

23-04-19

contact areacontact forcehardnessconstriction resistanceresistivitycontact spot diameter

Constriction resistanceone contact spotplastic deformation

23-04-19

Gold plated connector contact

0,5N contact normal force

Constriction resistance: 1m

23-04-19

Example

0,5 N contact normal force

hard gold, 160 HV (kp/mm2)

d = 0,02 mm

Rconstr. = 1,3 m

Measured, new contact: 11,3 m (bulk 10,0 m)

after use: 23,0 m (bulk 10,0 m)

=Resistance increase

Rconstr.

Contact area after use

Initial contact area

10

1=

1

100

23-04-19

Kontaktrörelse - återbildning

Contact area, cross section Contact surface seen from above

F

23-04-19

Kontaktrörelse - återbildning

Contact area, cross section Contact surface seen from above

F

23-04-19

Resistance/contact failures

Time

Resistans som funktion av tid/antal

Ack. number

23-04-19

Tenn – rensning av ytfilm

Contact area, cross section

Contact area, cross section Contact surface seen from above

F

23-04-19

Soft films onhard substrate

Hard films onsoft substrate

Squeeze and shear Crack

Noble metal contacts Base metal contacts

Friction force Contact force

Cylinder cylinder Rough surface, Ra>0,5

min 50-100m wipe

Rensning av ytfilmer, forts.

23-04-19

23-04-19

Frittingsilver, copper

23-04-19

Rensningsmekanismer, översikt

23-04-19

Termiska effekter

KontaktpunktCurrent constriction through contact spots –- constriction resistance- heat emission

Contact spot

23-04-19

Silver - temperaturökning

23-04-19

Tenn - temperaturökning

23-04-19

Failure mechanisms Contact force reduction

Initially too low contact force / variations Plastic deformation (manufacturing, closing) Stress corrocion cracking Stress relaxation

23-04-19

Stress relaxation

23-04-19

Failure mechanisms Contact force reduction

Initially too low contact force / variations Plastic deformation (manufacturing, closing) Stress corrocion cracking Stress relaxation

Film growth Corrosion Diffusion Contamination

23-04-19

Pore corrosion

Corrosion creep

23-04-19

Failure mechanisms Contact force reduction

Initially too low contact force / variations Plastic deformation (manufacturing, closing) Stress corrocion cracking Stress relaxation

Film growth Corrosion Diffusion Contamination

Wear Mating wear Fretting

23-04-19

Fretting oxidation/corrosion

23-04-19

Fretting risk – tangential force control

0

2

4

6

8

10

12

0 100 200 300 400 500 600Time (s)

Co

nta

ct

vo

lta

ge

dro

p (

mV

)

1.97 N 1.95 N 1.9 N 1.7 N 1.5 N

23-04-19

Design and materials Where is the spring?

design and materials spring properties

Contact material environmental resistance, requirements on contact force, surface geometry etc.

Housing mechanical stability, environmental resistance

23-04-19

Anslutningsdon

23-04-19

Open contact, not enclosed Closed contact, not enclosedOpen contact, enclosedClosed contact, enclosed

Bulletin No 102, ”Corrosion of Electronics”

AgCdO-relay – with/without enclosure, open/closed

lower limitG1

upper limitG2

23-04-19

AMP-don, tredje fjäder

23-04-19

IDC (Insulation displacemenet contacts)

23-04-19

Screw

23-04-19

Skruv med jordbricka, klimatprovning

Tin

Grounding washer

AluminiumPCB

1 Initial

2 Change of temp

3 Dry heat +85°C

4 Damp heat

5 Corrosion

Contact resistance

23-04-19

Skruv utan jordbricka, klimatprovning

1 Initial

2 Change of temp

3 Dry heat +85°C

4 Damp heat

5 Corrosion

Contact resistance

23-04-19

Sammanfattning