Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
ELECTRICAL CHANGES ELECTRICAL CHANGES
Prepared by:Jim Yancey, Victor StephensonState Property Code ServicesNC Dept of Insurance/OSFM919-661-5880 Ext. [email protected],[email protected]
Presented by:Dan Dittman, P.E.919-661-5880 Ext. 505 [email protected]
2008 NC Electrical Code
Article 708 (COPS)Article 708 (COPS)COPS•Critical Operations Power Systems
•Power systems for facilities or parts of facilities that require continuous operation for the reasons of public safety, emergency management, national security, or business continuity.
•Required in DCOA’s, Designated Critical Operations Areas, Areas within a facility or site designated as requiring critical operations power.
COPSCOPSOriginated by Homeland SecurityNot part of DOI Standard Review COPS requirements are not addressed in other State Building Codes– Complete Code compliance requirements are
presently undefinedDOI review for COPS compliance – Must be specifically requested by an Agency– Would result in recommendations that are
based on similar installations for Building Code compliance
COPSCOPS
Who Determines the Necessity and Location of COPS and DCOA’s?
– Any governmental agency having jurisdiction or by facility engineering documentation
• Municipal• State• Federal• Other Codes
COPSCOPSRefer to NFPA 1600-2007 Standard on Disaster/Emergency Management and Business Continuity Programs for more information on COPS
Emergency & Standby Power SystemsEmergency & Standby Power Systems
NCEC Defines how these systems are installed– Chapter 7 Special conditions
• Article 700 Emergency Systems• Article 701 Legally Required Standby
NCBC Chapter 27 determines where each system is required
Emergency & Standby PowerEmergency & Standby Power
The NCBC requires compliance with NFPA-110 and 111 for emergency and standby systems.
Emergency Power -Natural Gas GeneratorsEmergency Power -Natural Gas Generators
Natural Gas generators used for emergency service are approved on a project specific basis. – This will require an alternate material method
submittal by the designer along with a letter from the utility indicating their reliability.
– A copy of this type letter with the required contents is available from our office by request. [email protected].
DOI currently does not approve Natural Gas generators for fire pump service.
Smoke ControlSmoke ControlNCBC section 909.11 Power System requirements of a smoke control system ATS and the standby power source when located inside a building– Separate room from the normal power transformers and its
switchgear– This room(s) is to be enclosed by not less than 1-hour “fire
barriers”.– Emergency power equipment may also be in this same room. – This room must be ventilated directly to and from the exterior.
Smoke ControlSmoke Control
NCBC 909.11 requires 60 second transfer for smoke control systemsDOI requires that all smoke evac systems that affect egress be put on emergency power, the same practice as emergency lighting
Standby Power-ElevatorsStandby Power-ElevatorsNCBC section 3003.1-When Standby power is required for all elevators.– High Rise Buildings section 403.10.2 in
accordance with 1007.4 and 3003.– When the owner chooses to furnish
standby power to any elevator other than service elevators, it is required for all.
– Power must be able to be transferred manually to all elevators in each bank.
Emergency Power-PanelsEmergency Power-Panels
Compromised emergency systems-Emergency panels may only contain loads allowed by chapter 27 NCBC. Any others require special permission from DOI.
Fluorescent LuminairesFluorescent LuminairesArticle 410-130 –Disconnecting means is required for EACH fluorescent luminaire that has double-ended lamps and contains ballast(s) that may be serviced in place. – Exceptions
• 1. Not required in hazardous locations• 2. Not required for emergency illumination required in 700.16• 3. Not required for cord-and-plug• 4. Not required in industrial establishments with restricted
public access…• 5. Not required at each luminaire if design of the installation
includes disconnecting means such that the space cannot be left in total darkness. Neutral has to be disconnected.
Fluorescent LuminairesFluorescent LuminairesMultiwire Branch Circuits– The disconnecting means shall simultaneously break all
the supply conductors to the ballast, including the grounded conductor
Location of Disconnecting Means– Shall be located accessible to qualified persons before
servicing ballast. If external to luminaire, must be attached, or within sight of the luminaire
Electric Water CoolersElectric Water Coolers
Article 422.52 -Electric Water Coolers– Require GFCI protection – Please indicate this on your panel
schedules.
ClosingClosingRemember to put the e-mail address of the Owner and all designers on the Code Summary
Questions?Questions?
For further questions:Phone: 919 661-5880 Fax: 919 662-4414
On the e-mail, please include:
your name, agency affiliationphone number
CODE CHANGES CODE CHANGES
Prepared by:Dan Dittman, P.E.State Property Code Services 919-661-5880 Ext. 505 [email protected]
2009 NC Mechanical & Fuel Gas Code
Chap. 3 Condensate DisposalChap. 3 Condensate Disposal
NCMC 307.2.3 Auxiliary pans and secondary drains– Auxiliary drain pan with separate discharge– Equipment-provided drain pan with
separate discharge– Auxiliary drain pan with water-level
detection device, UL 508 Listed.– Equipment-provided drain pan with UL 508
water-level detection device
Ch. 4-VentilationCh. 4-Ventilation•Exit Enclosure Ventilation Restrictions
•Deleted from Mechanical Code•Still required by NCBC 1020.1.3
Ch-5 Exhaust SystemsCh-5 Exhaust Systems
502.5 Valve-Regulated Lead-Acid Battery Systems
– Room systems have been deleted from NCMC, but still included in NCFC 608.6.1
– Cabinet systems –no change
Exhaust Systems-Flammable FinishesExhaust Systems-Flammable Finishes
Termination Point of Exhausts Deleted from NCMC 502.7.3.6Still included in NCFC 1504.7.6
Except environmental air, as it is covered in NCMC 401.5
Exhaust Systems-Smoke ControlExhaust Systems-Smoke Control
Clarifies Methods Available to the designer for smoke control– Scale Modeling as defined in NFPA
92B– Algebraic Equations in NFPA 92B– Compartment Fire Models-Zone
Modeling or CFD Modeling (computational fluid dynamics)
Exhaust Systems-Smoke ControlExhaust Systems-Smoke Control
Section 513.8.1 Changes– Exhaust Rate Now consistent in NCMC,
NCBC, & NCFC as requiring…. “height of accumulating smoke layer shall be maintained at least 6 feet above walking surface”….
– References to makeup air flow rate “shall not exceed 200 fpm” are deleted from Mechanical, Fire, and Building Code, but it is included by reference of NFPA 92B
Exhaust Systems-Smoke ControlExhaust Systems-Smoke Control
Also Deleted from the NCMC, NCBC, & NCFC– NCMC 513.8.2 Axisymmetric
plumes– NCMC 513.8.3 Balcony Spill
Plumes– NCMC 513.8.4 Window Plumes– NCMC 513.8.5 Plume Contact
with Walls
Exhaust Systems –Smoke ControlExhaust Systems –Smoke Control
Design Fire changes Shall be based on a Rational Analysis performed by the registered design professional and approved by the code official. NCMC 513.9– Design fire fuel shall include consideration of the type of
fuel, fuel spacing and configuration– References to Design Fire Heat Release Assumption of
5000 Btu/s Q value are deleted
Exhaust Systems-Smoke ControlExhaust Systems-Smoke Control
NCMC Section 513.20 Underground Building Smoke Exhaust Systems– Prescriptive six ach design of Section 513.20,
513.20.1,2,&3 is deleted from NCMC– Deleted from Fire Code, formerly NCFC 909.20– Deleted from Building Code, formerly NCBC
909.21– NCBC 405.5 Smoke Control System for
underground buildings still refers to chapter 9, you still are required to provide smoke control, but not the prescriptive approach of 2006 NCBC 909.21
– NCBC 408.8 Windowless buildings, I-3 occupancy
Exhaust Systems –Smoke ControlExhaust Systems –Smoke Control
These changes may reduce the exhaust rates required compared to the more prescriptive approach available for use in the 2006 Code.
NCFG Clarification(s)NCFG Clarification(s)MP Regulators – Provide detail of device vent on drawings,– Or Model and Manufacturer(s) of regulators meeting the
vent limiting exception of 410.3.
Regulators Section 410.3.1 Vent Piping– Vent piping shall be run independently and serve only
one device vent– Combination vent and breather piping shall be run
independently and serve only one device– Breather only piping may be connected in a manifold
arrangement
Questions?Questions?For further questions:
Phone: 919 661-5880 Fax: 919 662-4414Dan Dittman, P.E.– [email protected]
Janie Sutton, P.E.– [email protected]
On the e-mail, please include:
your name, agency affiliationphone number