Elec Fitting Map and All NOS

8/13/2019 Elec Fitting Map and All NOS

1/27


2/27

ECIICESE01Install electrical cabling and wiring systems,enclosures and equipment (plant)

ECIICESE01 Install electrical cabling systems, wiring systems, enclosures and equipment (plant) 1

Overview This standard is about the installation of electrical cabling and wiring systems,

enclosures and equipment (plant) in engineering construction.

You will need to be able to carry out: isolation procedures and measuring and;

marking out for and installation of cabling and wiring systems, enclosures and

equipment whilst adhering to Health and safety legislation, regulations and safe

working practices.

In the context of this standard, your responsibility is to interpret and work within

given specifications, selecting techniques and making variations to achieve the

best possible result. In some cases, you may still be expected to refer to

others for final authorisation, even though you remain responsible foridentifying and implementing decisions.

This standard is for

Electrical installation engineers.


3/27

ECIICESE01

Install electrical cabling systems, wiring systems, enclosures and

equipment (plant)


Performance

criteria

You must be able to: P1 work safely at all times, complying with health and safety and other

relevant legislation, regulations, guidelines and local rules or procedures

P2 ensure that the work environment, material, equipment and tools are

suitably prepared for the activities to be undertaken

P3 identify the people that need to be provided with technical and functional

information

P4 obtain and interpret the required information and specification for the job

to be done

P5 confirm the existing electrical supply is compatible with the planned

installation

P6 identify accurately the means of electrical isolationand carry out

isolation

P7 measure and mark out for cabling systemsand wiring systems, cable

containment, enclosuresand equipment to specification

P8 check that the planned locations are sensible, visually acceptable and

are in accordance with other site services

P9 install the cabling and wiring systems, containment, enclosures and

equipment safely

P10 report to and gain approval from relevant people those necessary

amendments to the planned programme of work that may have:

P10.1 the potential to be dangerous

P10.2 a cost implication

P11 seek the appropriate action from the relevant people

P12 reinstate the work area

P13 deal promptly and effectively with problems within your control and report

those that cannot be solved


4/27

ECIICESE01


equipment (plant)


Knowledge and

understanding

You need to know and

understand:

K1 relevant legislative, regulatory and local requirements or procedures and

safe working practices

K2 preparation and reinstatement requirements in respect of the work area,

material, and equipment, and the possible consequences of incorrect

actions in these areas

K3 how to identify people that need to be supplied with technical and

functional information relating to the task

K4 risk assessments and method statements (RAMs) and other related

documentation and procedures

K5 engineering drawings and related specifications

K6 the tools, terminology and techniques for the installation of cabling and

wiring systems, containments, enclosures and equipment

K7 safe isolation procedures

K8 correct positioning and installation of components

K9 your responsibilities for ensuring care and security of tools and

equipment used

K10 reporting and documentation procedures

K11 your responsibilities with regard to reporting lines and procedures in your

working environment


5/27

ECIICESE01


equipment (plant)


Addi tional Informat ion

Scope/range Work environment

Typical work environments could include:

1 at height

2 confined spaces

3 controlled operational and offshore installations

4 designated work areas

5 engineering construction sites

6 existing plants and structures

7 fabrication workshops

8 nuclear sites

9 onshore and offshore installations

10 potential explosive atmospheres

11 shafts

12 shipyards

13 tunnels

14 working inside plant and systems

15 working on access structures (scaffold)

Electrical isolation

This could include:

1 getting appropriate authorisation including Permit to Work

2 identifying the correct isolations and disconnections required

3 correct sequence of isolations and disconnections

4 safety methods for maintaining isolations and disconnections

Cabling systems

These systems could include:

1 control cables

2 data cabling

3 earth cabling

4 power cables

5 telemetry cables


6/27

ECIICESE01


equipment (plant)


Cable containment

Cable containment could include:

1 cable ladder, tray and, basket systems

2 ducting systems

3 PVC and steel conduit

4 PVC and steel trunking

Enclosures

These could include:

1 junction boxes

2 local control panels

3 marshalling boxes

Reinstate the work area

This term could include:

1 returning the work area to a safe condition

2 correctly disposing of waste materials

3 storage of re-usable materials, consumables and equipment in

accordance with appropriate procedures

4 completion of all necessary documentation

Information relating to the task

This could include knowledge and understanding about

1 sources of technical and functional information

2 who should receive what information

3 the type of information to supply

4 when to supply information

5 checking that the relevant people understand those aspects of

information that have a bearing on health and safety

Engineering drawings and related specifications

Engineering drawings could include:

1 assembly instruction


7/27

ECIICESE01


equipment (plant)


2 general arrangement (GAs)

3 isometrics

4 schematics

5 schedules

Specifications could include:

6 method statements

7 manufacturers instructions

8 product worksheets


8/27

ECIICESE01


equipment (plant)


Developed by Engineering Construction Industry Training Board

Version number 1

Date approved February 2013

Indicative reviewdate

February 2017

Validity Current

Status Original

Originatingorganisation

Engineering Construction Industry Training Board

Original URN NETI04SS23

Relevantoccupations

Electrical Engineer ; Electrical Fitter; Electrical Maintenance Technician;Electrical supervisor; Electrician; Electrical Installation Engineer; LeadTechnician

Suite Installation, Testing and Commissioning of Electrical Systems and Equipment(Plant)

Key words Engineering; installation; cabling systems; wiring systems; isolation;construction; containment; wiring enclosures; enclosures; wiring; cabling;

electrical installation; installation; electrical


9/27

ECIICESE02Terminate cabling systems, wiring systems andequipment (plant)

ECIICESE02 Terminate cabling systems, wiring systems and equipment (plant) 1

Overview This standard is about the termination of cabling systems and wiring systems

and equipment (plant) in engineering construction.

You will need to be able to make terminations according to specification and

check they are electrically and mechanically sound using the correct tools and

techniques whilst isolating the plant according to procedures and adhering to

Health and safety legislation, regulations and safe working practices.








10/27

ECIICESE02

Terminate cabling systems, wiring systems and equipment (plant)


Performancecriteria






information


to be done


isolation

P6 make terminations of cabling systems, wiring systems, enclosuresand

equipment in accordance with specifications and regulations

P7 ensure all terminations are complete

P8 check the terminations are electrically and mechanically sound

P9 ensure terminations are identified correctly and clearly

P10 identify and remedy any defects found after termination has taken place

P11 complete necessary documentation

P12 reinstate the work area

P13 deal promptly and effectively with problems within your control and report



11/27

ECIICESE02



Knowledge andunderstanding


understand:





actions in these area





K5 the tools, terminology and techniques for terminating cabling systems,

wiring systems, enclosures and equipment



K8 safe termination methods


equipment used



working environment


12/27

ECIICESE02






1 at height

2 confined spaces






8 nuclear sites



11 shafts

12 shipyards

13 tunnels




This could include:





Cabling systems

These systems could include:

1 control cables

2 data cabling

3 earth cabling

4 power cables

5 telemetry cables


13/27

ECIICESE02



Enclosures

These could include:

1 junction boxes

2 local control panels

3 marshalling boxes














5 checking that the relevant people understand those aspects of

information that have a bearing on health and safety


Engineering drawings could include:1 assembly instruction


3 isometrics

4 schematics

5 schedules


6 method statements


14/27

ECIICESE02






15/27

ECIICESE02




Version number 1



February 2017

Validity Current

Status Original




Relevantoccupations

Electrical Engineer ; Electrical Fitter; Electrical Maintenance Technician;Electrical Supervisor; Electrician; Electrical Installation Engineer


Key words Engineering; termination; cabling systems; wiring systems; isolation;construction; enclosures; wiring; cabling; electrical installation; installation;

electrical


16/27

ECIICESE03Inspection, testing and commissioning of electricalinstallations (plant)

ECIICESE03 Inspection, testing and commissioning of electrical installations (plant) 1

Overview This standard is about the inspecting, commissioning and testing of electrical

installations (plant) in engineering construction.

You will need to be able to perform the appropriate tests, ensure that the

installation is in accordance with regulations and prepare a test record using

the correct tools and techniques and adhering to Health and safety legislation,

regulations and safe working practices.








17/27

ECIICESE03

Inspection, testing and commissioning of electrical installations (plant)


Performancecriteria






information


to be done


isolation

P6 confirm that your test instruments are:

P6.1 appropriate

P6.2 fit for purpose

P6.3 calibrated

P7 plan and agree the schedule for inspecting and testing procedures

P8 conduct an inspection

P9 conduct the required tests

P10 confirm the installation meets the required regulations and standards

P11 prepare a formal record of testing which confirms the safety and integrity

of the installation

P12 commission the installation according to specification and defined

parameters

P13 reinstate the work areaP14 deal promptly and effectively with problems within your control and report



18/27

ECIICESE03



Knowledge andunderstanding


understand:





actions in these areas







K7 the tools, terminology and techniques for inspecting, testing and

commissioning electrical installations including:

K7.1 identification of inspection requirements

K7.2 selection of appropriate calibrated testing equipment

K7.3 sequencing of tests for fault identification

K7.4 setting up of equipment to predetermined parameters

K7.5 releasing of equipment into service


equipment used



working environment


19/27

ECIICESE03






1 at height

2 confined spaces






8 nuclear sites



11 shafts

12 shipyards

13 tunnels




This could include:





Testing procedures

These could include testing

1 continuity

2 earth fault loop impedance

3 insulation resistance

4 operation of electrical components

5 polarity


20/27

ECIICESE03
















5 checking relevant people understand those aspects of information that

have a bearing on health and safety





3 isometrics

4 schematics

5 schedules


6 method statements




21/27

ECIICESE03




Version number 1



February 2017

Validity Current

Status Original




Relevantoccupations



Key words Engineering; testing; inspection; isolation; construction; calibrate; testequipment; wiring; cabling; electrical installation; commissioning; electrical;

construction


22/27

ECIICESE04Diagnose and correct electrical faults (plant)

ECIICESE04 Diagnose and correct electrical faults (plant) 1

Overview This standard is about diagnosing and correcting electrical faults (plant) in

engineering construction.

You will need to be able to diagnose and correct faults using the correct tools

and techniques whilst isolating the plant in accordance with approved

procedures and adhering to Health and safety legislation, regulations and safe

working practices.








23/27

ECIICESE04

Diagnose and correct electrical faults (plant)


Performancecriteria



P2 ensure that the work environment, material, electrical equipmentand

tools are suitably prepared for the activities to be undertaken

P3 obtain detailed information relating to the faultsincluding the

specification of the faulty equipment


information


to be done


isolation

P7 carry out tests to identify the fault

P8 agree the repairs and costs and gain approval

P9 correct the faults to specification

P10 ensure all necessary terminations are complete and the installation is

safe

P11 inspect and test that the repaired electrical equipment is functioning to

specification

P12 identify and report potential modification to the design or operation of the

installation in order to avoid future failures

P13 complete necessary documentation

P14 reinstate the work areaP15 deal promptly and effectively with problems within your control and report



24/27


25/27

ECIICESE04






1 at height

2 confined spaces






8 nuclear sites



11 shafts

12 shipyards

13 tunnels




This could include:













26/27

ECIICESE04









5 checking relevant people understand those aspects of information that

have a bearing on health and safety





3 isometrics

4 schematics

5 schedules


6 method statements




27/27

ECIICESE04



Version number 1



February 2017

Validity Current

Status Original




Relevantoccupations



Key words Engineering; faults; cabling systems; wiring systems; isolation; construction;diagnosis; diagnose; correct; calibrated equipment; testing; commissioning;

enclosures; wiring; cabling; electrical installation; installation; electrical

Documents

Elec Fitting Map and All NOS