Upload
qui-nguyen
View
296
Download
0
Embed Size (px)
Citation preview
Effects of BPO on Boron Nitride UK 5 and UK 10 in
WaterQui Nguyen
Repeat the experiment using BPO because the BPO I used last time was contaminated.
Procedure
- 4.4 mg of Boron Nitride- 5 mL of water- 15 mg of BPO- Bath sonicated for 30 minutes
Before bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
Right after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
Right after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
5 minutes after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
5 minutes after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
1 hour after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
1 hour after bath sonication
BN UK 5WaterBPO
BN UK 5Water
BN UK 10WaterBPO
BN UK 10Water
Qui Nguyen
Effects of BPO on Boron Nitride UK 5 and UK 10 in
Heptane
Before bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
Before bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
Right after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
Right after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
5 minutes after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
5 minutes after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
30 minutes after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
30 minutes after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
1 hour after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
1 hour after bath sonication
BN UK 5HeptaneBPO
BN UK 5Heptane
BN UK 10HeptaneBPO
BN UK 10Heptane
Thin film
I tried to make the thin film using the same procedure from Steve, but this time I did not dilute the PVDF solution. The thin film came out better, thicker, and stronger; however, the thin film shrinked. I was able to measure the conductivity of the thin film, and it was about 5.6-7.8 MΩ.
Thin film
- 6 mg of G3243- 5 mL of Heptane- 5 mL of water- used around 2 mL of PVDF
Future work
I’m going to try casting different concentration of the PVDF on the thin film. The thin film I made the first time was too thin, and the second time was thick but it shrinked. I think It will be better if I try to dilute a different amount of PVDF in DMAC.