EF6C Disassembly Procedure

8/13/2019 EF6C Disassembly Procedure

1/11

D I S A S S E M B L Y P R O C E D U R E

3 - 1

Chapter

Disassembly Procedure

BATTERY Module The below illustrations show how to Remove the Battery module from the notebook.Disassembling BATTERY Module

1. Push the latch and take out the battery!

Removing HDD Module1. Loosen 2 screws on bottom of notebook.

Twist force: 2.0+/ -0.2KG/ CM. Number 1 cross screwdriver2. Push the HDD module off the front side of notebook.

H D D M O D U L E

R E M O V E

B A T T E R Y

R E M O V E

B A T T E R Y

M O D U L E

D I S A S S E M B L

Y


2/11


4 - 2

Memory Module The below illustrations show how to remove the Memory module from the notebook.

Disassembling Memory module1. Loosen screw and Disassemble RAM door. Twist force: 2.0+/ -0.2KG/ CM. Number 1 cross screwdriver

2. Pushed the brackets and taken out the RAM.

M E M O R Y

M O D U L E

M E M O R Y

R E M O V E

2


3/11


4 - 3

Remove Wireless Module1. Loosen the screw then disassembled MINIPCI door.

Twist force: 2.0+/-0.2KG/CM. Number 1 cross screwdriver

2. Carefully taken off antenna cable.

3. Removed wireless card from MiniPCI slot.

Keyboard ModuleThe illustration below shows how to remove the K/B cover and keyboard plate.Removing Keyboard cover1. Pushed the cover to take off.

K / B C O V E R

R E M O V E

W I R E L E S S

M O D U L E

R E M O V E

K / B M O D U L E


4/11


4 - 4

Removing K/BPushed up the K/B and disconnected the K/B cable.

Remove ROM driver1. Loosen the screw and Pushed out the ODD module.

Twist force: 2.0+/ -0.2KG/ CM. Number 1 cross screwdriver

K / B

D I S A S S E M B L Y

R O M D R I V E R

R E M O V E


5/11


4 - 5

Removing the metal sheet1. Loosen the screws and taken off the metal sheet.

Twist force: 2.0+/ -0.2KG/ CM. Number 1 cross screwdriver

CPU Module The illustrations below show how to remove the CPU module onto the notebook. The module contains CPU, CPU thermal pad and CPU heatsink module.Removing CPU Fan

1. Loosen the screws and disconnect fan cable. Then take off the fan. Twist force: 2.0+/ -0.2KG/CM. Number 1 cross screwdriver

C P U F A N

R E M O V E

C P U

M E T A L S H E E T

R E M O V E


6/11


4 - 6

2. To loose CPU with minus screw driver and follow the arrow direction. Thentake off CPU and taken off the thermal pad.

LCD MOUDLEThe illustration below shows how to remove LCD.Removing LCD cover1. Loosen the screws.


L C D R E M O V E

L C D C O V E R

R E M O V E

2

1


7/11


4 - 7

2. Disconnect LCD cable and Antenna cable. Then taken out the Cover.Disassembling LCD1. Carefully loosen the screws on the bezel and taken off bezel.


L C D R E M O V E

2

1

1


8/11


4 - 8

2. Disconnected I/ V and loosen screws on the bracket. Then taken out LCD.Twist force: 2.0+/-0.2KG/CM. Number 1 cross screwdriver


9/11


4 - 9

M/B Module The illustration below shows how to remove the M/B from the base.Removing top1. Loosen the screws on the base.


2. Loosen the screws on the top.Twist force: 2.0+/-0.2KG/CM. Number 1 cross screwdriver

T O P R E M O V E

M / B M O D U L E


10/11


4 - 10

3. Disconnected touch pad cable and taken off top.

Disassembling M/B1. Loosen the nuts on the base.


M / B R E M O V E


11/11


4 - 11

2. Loosen the screws on the docking bracket and taken off bracket.Twist force: 2.0+/-0.2KG/CM. Number 1 cross screwdriver

3. Loosen the screws on the M/B.Twist force: 2.0+/-0.2KG/CM. Number 1 cross screwdriver

4. Disconnected LID switch cable and speaker cable. Then taken off M/B.

3

4

Documents

EF6C Disassembly Procedure