EC axial fans - HyBlade®

sickled blades (S series) with full square nozzle, Ø 710

Highlights: – 5-blade fan, 3-phase fan motor – 10 VDC max. output / 10 mA, 20 VDC max. output / 50 mA, 0-10 V slave output, 24 V external program input, 0-10 VDC / PWM control input, 0-10 V or 4-20 mA sensor input, motor current limit– Integrated PID controller, RS485 MODBUS RTU technology – Over-temperature protected electronics / motor, alarm relay – Soft start, PFC passive, line undervoltage / phase failure detectionMaterial: Guard grille: Steel, coated in black plastic Wall ring: Sheet steel, pre-galvanised and black powder paint Blades: Aluminum sheet insert, sprayed with PP plastic Electronic enclosure: Die-cast aluminum, coated in black Mounting position: Shaft horizontal on rotor on bottom; rotor on top on request Condensate discharge holes: Rotor-side Direction of rotation: Clockwise, seen on rotor

(1) Nominal data at maximum load.

Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LPA measured at 1m distance to fan axis. The acoustic values given are valid under the measuring conditions mentioned and may vary accoring to the actual installation situation. With any deviation to the standard set-up, the specific values have to be checked and reviewed once installed or fitted.

For detailed information on the measuring set-up, please contact ebm-papst.

Curvesn

rpm

Pe

W

I A

(460V)

I A

(230V)

LwAin

dB(A)

Nominal Data Air fl

ow

Nom

inal

vol

tage

rang

e

Freq

uenc

y

Pow

er in

put (

1)

Spee

d (1

)

Curr

ent d

raw

(1)

Tem

pera

ture

rang

e (1

)

Mas

s

Ingr

ess

prot

ectio

n ra

ting

Elec

trica

l wiri

ng d

iagr

am

UL

Type Motor CFM VAC Hz Watts RPM A °C lbs

W3G710-GS28-11F M3G150-FF 12,000 200...240 50/60 1,700 1,030 4.8 -25...60 85 IP54 A Yes

W3G710-GS30-01F M3G150-FF 12,000 380...480 50/60 1,700 1,030 2.3 -25...70 85 IP54 A Yes

Pfa [Pa]

Pfa [Pa]

Pfa [Pa]

0 2,000 6,0004,000 8,000 10,000 12,000 cfm

0.2

0.3

0.4

0.8

in

. wg

4,000 8,000 12,000 16,000 20,000 m3/h

240

200

160

120

80

40

9

10

11

127

6

8

5

3

4

1

2

13

14

15

16

0.9

0.1

0.6

0.5

0.7

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1030 1323 1.8 3.4 74

1030 1451 1.9 3.8 73

1030 1587 2.1 4.1 74

1030 1700 2.3 4.8 78

900 867 1.1 2.2 71

900 964 1.3 2.5 70

900 1052 1.4 2.7 71

900 1123 1.5 2.9 75

750 502 0.7 1.3 67

750 558 0.7 1.4 66

750 609 0.8 1.6 67

750 650 0.9 1.7 71

600 257 0.3 0.7 62

600 286 0.4 0.7 62

600 312 0.4 0.8 62

600 333 0.4 0.9 66

W3G710-GSXX-XXF with full square nozzle

Cable diameter: min. 4 mm,max. 10 mm,tightening torque: 4±0.6 Nm

Tighteningtorque3.5±0.5 Nm

Ø0.5

7 (1

4.5

(4x)

)

31.89 (810+1)

33.46 (850-3)

Direction of air flow "V"

6.69 (170)

10.708 (272±5)

0.79 (20)Ø3

0.39

(772

)

Dimensions shown in inches (mm)