Upload
others
View
24
Download
0
Embed Size (px)
Citation preview
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
www.gansecshengyuean.com/[email protected]
Earthing & Lightening Protection
Products
http://www.gansecshengyuean.com/
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
2
EARTHING & LIGHTENING PROTECION
PRODUCTS INDEX
SLNO TOPIC PAGE NO
1 COPPERBOND EARTH RODS & ACCESSORIES 3-5
2 SOLID COPPER EARTH RODS & ACCESSORIES 6-7
3 TINNED SOLID COPPER EARTH RODS & ACCESSORIES 8-9
4 STAINLESS STEEL EARTH RODS & ACCESSORIES 10-11
5 GALVANISED STEEL EARTH ROD 11
6 EARTH ROD TO TAPE ‘A’ CLAMPS 12-13
7 EARTH ROD TO CABLE ‘G’ CLAMPS 13
8 ‘U’ BOLT CLAMPS 14
9 SPLIT CONNECTOR CLAMPS 15
10 ‘U’ BOLT & UNIVERSAL BEAM CLAMP 16
11 MULTIPURPOSE & REBAR CLAMP 17
12 REBAR X CLAMP 18
13 STAINLESS STEEL REBAR CLAMPS 18
14 PIPE CLAMPS 19
15 SOLID COPPER EARTH PLATES 19
16 SOLID COPPER & STEEL LATTICE MATS 20
17 TOWER EARTH & PARALLEL GROOVE CLAMPS 21
18 EARTH BONDING POINTS 22-25
19 EARTH BARS 26-31
20 DISCONNECTING LINK & INSULATORS 32
21 EARTH BLOCK & BOSSES 33-34
22 SPLIT BOLT CONNECTORS 35
23 HV SURGE COUNTER COUPLING 35
24 COPPER BRAID BONDS 36-49
25 ‘C’ CRIMP CONNECTORS 41 27 COMPRESSION CABLE LUGS 42-45
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
3
INDEX
SLNO TOPIC PAGE
NO
28 TAPER POINT RODS 48
29 MULTI POINT & AIR ROD SADDLES 49
30 SIDE MOUNTING AIR ROD BRACKETS & METALLIC DC CLIPS 50-51
31 NON METALLIC DC CLIPS 51-52
32 ROD TO TAPE COUPLINGS 52
33 TAPE CLIPS 53
34 ADHESIVE DC CLIPS 54
35 HOLD FASTS 54-55
36 WATER MAIN PIPE BOND & STRIKE PAD 56
37 WATER PROOF SEALING TAPE 57
39 RAINWATER PIPE BOND & PUDDLE FLANGE 58
40 CONDUCTORS 59-66
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
4
Nominal Size
L mm
Thread Size
(UNC-2A)
Shank D mm
L1 mm
Unit Weight kg
Part Number
1/2 ”
1200
9/16 ”
12.7
30
1.18 GS ERB C12
1500 1.55 GS ERB C15
1800 1.76 GS ERB C18
2400 2.36 GS ERB C24
5/8 ”
1000
5/8 ”
14.2
30
1.28 GS ERB A10
1200 1.53 GS ERB A12
1200 40 1.53 GS ERB A12S
1500 30
1.95 GS ERB A15
1800 2.23 GS ERB A18
2400 3.00 GS ERB A24
2400 40 3.00 GS ERB A24S
3000 30 3.70 GS ERB A30
3/4 ”
1000
3/4 ”
17.2
35
1.65 GS ERB B10
1200 2.20 GS ERB B12
1500 2.76 GS ERB B15
1800 3.26 GS ERB B18
2400 4.45 GS ERB B24
3000 5.48 GS ERB B30
1 ” 2400 1 ” 23.0 50 2.43 GS ERB D24
3000 3.04 GS ERB D30
COPPERBOND EARTH RODS
The reason for the enduring popularity and appeal of this product is that it represents a known technology, the driven earth rod, and combines the conductive properties of copper with the strength of steel. They offer a more economical and stronger alternative to a pure copper rod and a better conductivity than a stainless steel rod, whilst maintaining its corrosion resistant properties
Each rod has a high tensile strength, low carbon steel core. 99.95% pure copper is applied electrolytically and forms a metallurgical bond between the steel core and the copper.
The threads are formed by a cold rolling process which ensures strength and maintains the molecularly bonded copper covering along the full length of the threads. Cold-rolled threads are stronger than cut-threads.
The standard copper thickness is 0.25mm. Greater copper thicknesses are also available. Please contact our sales office for further information.
THREADED
Material: Pure copper molecularly bonded onto a steel core.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
5
UNTHREADED
THREADED COUPLINGS
These high-strength couplings are used for joining copperbond
threaded earth rods together. They facilitate deep driving and
ensure continual contact between the rods both during and after
installation.
The coupling also protects the earth rod threads during installation
with the threaded driving head. There is a lead-in for ease of
assembly and the hexagonal design allows for grip and keeping the
coupling tight when driving into the ground. All Gansec
Shengyuean couplings are manufactured from a high copper
content alloy ensuring excellent corrosion resistance.
Nominal Size L mm
Shank D mm
Unit Weight kg
Part Number
3/8 ” 1200 9.5 0.62 GS ERB E12
1 ” 3000 25.4 22.50 GS ERB E30
Type L mm
D mm
Unit Weight kg Part Number
1/2 ” 68 18 0.07 GS C 12
5/8 ” 68 20 0.12 GS C 58
3/4 ” 78 25 0.14 GS C 34
1 ” 100 31 0.25 GS C 1
Type L mm
D mm
Unit Weight kg Part Number
5/8 ” 80 21 0.08 GS C 58 SB
Material: Pure copper molecularly bonded onto a steel core
Material: High Copper Alloy
Material: Silicon Bronze.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
6
Type L mm
D mm
Unit Weight kg Part Number
1/2 ” 50 20 0.08 GS DH 1/2
5/8 ” 55 22 0.08 GS DH 5/8
3/4 ” 60 25 0.13 GS DH 3/4
3/4 ” 120 22 0.30 GS DH 3/4 22
3/4 ” 60 30 0.15 GS DH 3/4 30
Type L mm
D mm
Unit Weight kg Part Number
5/8 ” 47 27 0.08 GS DH 5/8 CCS
THREADED DRIVING HEADS
Material: Steel.
* The ERBD 21 is a driving head with a 3/4” thread and a 5/8” head.
Material: Copper Coated Steel
These are re-usable threaded driving heads are suitable for driving copperbond threaded earth rods by hand or with a power hammer.
The driving head screws into the threaded coupling to allow deep
driving of the earth rods.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
7
Shank D mm
L mm
Thread Size
L1 mm
Unit Weight kg
Part Number
15 1200 M10 20 1.88 GS PCR 15/1.2
16
1500
M10
20
2.66 GS PCR 16/1.5
1800 3.20 GS PCR 16/1.8
2400 4.28 GS PCR 16/2.4
3000 5.36 GS PCR 16/3.0
20
1200
M10
20
3.34 GS PCR 20/1.2
1500 4.18 GS PCR 20/1.5
1800 5.03 GS PCR 20/1.8
2400 6.71 GS PCR 20/2.4
2500 7.00 GS PCR 20/2.5
3000 8.40 GS PCR 20/3.0
25
1000
M12
25
4.37 GS PCR 25/1.0
1200 5.25 GS PCR 25/1.2
1500 6.54 GS PCR 25/1.5
1800 7.86 GS PCR 25/1.8
2000 8.73 GS PCR 25/3.0
2400 10.50 GS PCR 25/2.4
2500 10.90 GS PCR 25/2.5
3000 13.10 GS PCR 25/3.0
3600 15.90 GS PCR 25/3.6
SOLID COPPER EARTH RODS
Copper earth rods offer exceptional current transference
performance and can be used in a number of aggressive grounds
as their corrosion resistance is impressive. As copper is not as
strong as steel, or copperbonded rods, in rocky or densely
compressed ground areas installation engineers should not drive
the rods, they should first excavate boreholes and install them
properly to avoid bending or breaking the earth rods and increase
the effectiveness of the earthing application. With a range of
standard fittings the Gansec Shengyuean earth rod is recognised
for its high performance and long life-span.
Material: Copper to BS EN 13601
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
8
DRIVING HEADS
DRIVING SPIKES
COUPLING DOWELS
D mm
L mm
Thread Size
L1 mm
Unit Weight kg
Part Number
16 38 M10 20 0.03 GS DH 10
20 41 M10 20 0.06 GS DH 10/20
25 45 M12 25 0.10 GS DH 12
D mm
L mm
Thread Size
L1 mm
Unit Weight kg
Part Number
16 42 M10 20 0.03 GS DS 10
20 51 M10 20 0.06 GS DS 10/20 25 60 M12 25 0.10 GS DS 12
Thread Size L mm
Unit Weight kg Part Number
M10 40 0.02 GS CD 10 M12 50 0.04 GS CD 12
The driving head protects the internal
thread and the top of the solid copper earth
rod from damage when being driven into
the ground.
Material: Steel
These driving spikes enable solid copper earth rods to be driven easily into the ground.
Material: Steel
The phosphor bronze coupling dowel is used for joining solid copper earth rods together.
Material: Phosphor Bronze
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
9
Shank D mm
L mm
Thread Size
L1 mm
Unit Weight kg
Part Number
15 1200 M10 20 1.88 GS ERC 15/1.2
16
1500
M10
20
2.66 GS ERC 16/1.5
1800 3.20 GS ERC 16/1.8
2400 4.28 GS ERC 16/2.4
3000 5.36 GS ERC 16/3.0
20
1200
M10
20
3.34 GS ERC 20/1.2
1500 4.18 GS ERC 20/1.5
1800 5.03 GS ERC 20/1.8
2400 6.71 GS ERC 20/2.4
2500 7.00 GS ERC 20/2.5
3000 8.40 GS ERC 20/3.0
25
1000
M12
25
4.37 GS ERC 25/1.0
1200 5.23 GS ERC 25/1.2
1500 6.54 GS ERC 25/1.5
1800 7.86 GS ERC 25/1.8
2000 8.73 GS ERC 25/2.0
2400 10.50 GS ERC 25/2.4
2500 10.90 GS ERC 25/2.5
3000 13.10 GS ERC 25/3.0
3600 15.90 GS ERC 25/3.6
These earth rods are designed for use where extremely high
corrosion resistance and exceptionally long life are required.
Tinned solid copper earth rods are produced from solid copper
bar and are internally threaded for jointing. When deep
driving a tinned solid copper earth rod the usual practice is to
insert the rod into a bore hole and backfill with either Low-
Resistance Earthing Compound or Bentonite.
TINNED SOLID COPPER EARTH RODS
Material: Copper to BS EN 13601.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
10
DRIVING SPIKES
COUPLING DOWELS
D mm
L mm
Thread Size
L1 Mm
Unit Weight kg Part Number
16 38 M10 20 0.03 GS DH 10
20 41 M10 20 0.06 GS DH 10/20
25 45 M12 25 0.10 GS DH 12
D mm
L mm
Thread Size
L1 mm
Unit Weight kg Part Number
16 42 M10 20 0.03 GS DS 10 20 51 M10 20 0.06 GS DS 10/20
25 60 M12 25 0.10 GS DS 12
Thread Size L mm
Unit Weight kg Part Number
M10 40 0.02 GS CD 10 M12 50 0.04 GS CD 12
DRIVING HEADS
The driving head protects the internal thread and
the top of the tinned solid copper earth rods from
damage when being driven into the ground.
Material: Steel.
These driving spikes enable tinned solid
copper earth rods to be driven easily into
the ground.
Material: Steel.
The phosphor bronze coupling dowel is
used for joining solid copper earth rods
together.
Material: Phosphor Bronze
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
11
Shank D mm
L mm
Thread Size
L1 mm
Unit Weight kg Part Number
16
1200
M10
20
1.87 GS ERS 16/1.2
1500 2.35 GS ERS 16/1.5
1800 2.83 GS ERS 16/1.8
2400 3.74 GS ERS 16/2.4
3000 4.75 GS ERS 16/3.0
20
1200
M10
20
2.95 GS ERS 20/1.2
1500 3.79 GS ERS 20/1.5
1800 4.46 GS ERS 20/1.8
2400 6.10 GS ERS 20/2.4
3000 7.57 GS ERS 20/3.0
25
1200
M12
25
4.64 GS ERS 25/1.2
1500 5.81 GS ERS 25/1.5
1800 6.99 GS ERS 25/1.8
2400 9.34 GS ERS 25/2.4
3000 11.69 GS ERS 25/3.0
D mm
L mm
Thread Size
L1 Mm
Unit Weight kg Part Number
16 38 M10 20 0.03 GS DH 10
20 41 M10 20 0.06 GS DH 10/20
25 45 M12 25 0.10 GS DH 12
STAINLESS STEEL EARTH RODS
These earth rods are designed for use where
problems may be caused by galvanic corrosion
due to dissimilar metals being buried in close
proximity. They are produced from stainless
steel rod and are internally threaded for
jointing.
Material: Stainless Steel to BS EN 10088.
DRIVING HEADS
The driving head protects the internal thread
and the top of the tinned solid copper earth
rods from damage when being driven into the
ground.
Material: Steel.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
12
DRIVING SPIKES
COUPLING DOWELS
GALVANISED STEEL EARTH ROD
SET
D mm
L mm
Thread Size
L1 mm
Unit Weight kg Part Number
16 42 M10 20 0.03 GS DS 10
20 51 M10 20 0.06 GS DS 10/20
25 60 M12 25 0.10 GS DS 12
Thread Size L mm
Unit Weight kg Part Number
M10 40 0.02 GS CD 10 M12 50 0.04 GS CD 12
Nominal Size
L mm
Thread Size (BSF)
D mm
L1 mm
L2 mm
Unit Weight kg Part Number
5/8 ” 1200 3/8 ” 16.5 - 17.0 30 25 2.10 GS ERG 5/8
These driving spikes enable tinned solid
copper earth rods to be driven easily into
the ground.
Material: Steel.
The phosphor bronze coupling dowel is
used for joining solid copper earth rods
together.
Material: Stainless Steel
This galvanised steel earth rod has a male thread at the
top and a female thread at the bottom enabling rods
to be joined together.
After machining, the rod is hot-dip galvanised with a coating Of zinc not less than 610 g/m2
The rod is supplied as a standard set complete with
toughened steel driving head, hardened steel driving spike and
galvanised steel wire rope grip.
Material: Mild Steel galvanised to BS EN ISO 1461.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
13
EARTH ROD TO TAPE ‘A’ CLAMPS
Earth Rod Shank Ø mm
Maximum Tape Size
mm
L mm
W mm
H mm
Unit Weight kg
Part Number
12.7
26 x 15 43 36 19 0.12 GS A 26/12
32 x 15 42 44 18 0.13 GS A 32/15
39 x 15 46 52 23 0.20 GS A 39/15
14.2
26 x 14 43 36 19 0.12 GS A 26/14
32 x 14 42 44 18 0.13 GS A 32/14
39 x 14 46 52 23 0.20 GS A 39/14
51 x 16 48 63 20 0.20 GS A 51/16
15.0
26 x 13 43 36 19 0.12 GS A 26/13
32 x 13 42 44 18 0.13 GS A 32/13
39 x 13 46 52 23 0.20 GS A 39/13
51 x 15 48 63 20 0.20 GS A 51/15
16.0
26 x 12 43 36 19 0.12 GS A 26/12
32 x 12 42 44 18 0.13 GS A 32/12
39 x 12 46 52 23 0.20 GS A 39/12
51 x 14 48 63 20 0.20 GS A 51/14
17.2
26 x 11 43 36 19 0.12 GS A 26/11
32 x 11 42 44 18 0.13 GS A 32/11
39 x 11 46 52 23 0.20 GS A 39/11
51 x 13 48 63 20 0.20 GS A 51/13
26 x 18 54 38 22 0.17 GS A 26/18
20.0
26 x 8 43 36 19 0.12 GS A 26/8
32 x 8 42 44 18 0.13 GS A 32/8
39 x 8 46 52 23 0.20 GS A 39/8
51 x 10 48 63 20 0.20 GS A 51/10
26 x 16 54 38 22 0.17 GS A 26/16
25.0 26 x 11 54 38 22 0.17 GS A 26/11
These are popular clamps used for
joining earth rods to different sizes of
copper tape. The clamps have a high
resistance to corrosion and are
mechanically strong to ensure a lasting
connection.
Material: Aluminium Bronze with M10 x 25mm Phosphor Bronze Set
Screw.
*The ERA 1625 comes with a Stainless Steel Grade 316 Set Screw.
.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
14
EARTH ROD TO CABLE ‘G’ CLAMPS
Earth Rod Shank Ø mm
Maximum Tape Size
mm
L mm
W mm
H mm
Unit Weight
kg
Part Number
16.0 26 x 12 45 37 19 0.06 GS A 26/12 S
Earth Rod Shank Ø mm
Conductor Range mm
L mm
W mm
H mm
Unit Weight kg
Part Number
9.5 6 - 35 30 20 15 0.05 GS G 9.5/635
12.7 6 - 35 36 28 18 0.07 GS G 12.7/635
35 - 70 41 26 20 0.08 GS G 12.7/3570
14.2
6 - 16 36 28 18 0.07 GS G 14.2/616
16 - 70 41 26 20 0.08 GS G 14.2/1670
35 - 150 48 30 18 0.09 GS G 14.2/35150
15.0
6 - 16 36 28 18 0.07 GS G 15.0/616
16 - 70 41 26 20 0.08 GS G 15.0/1670
25 - 150 48 30 18 0.09 GS G 15.0/25150
16.0 6 - 70 41 26 20 0.08 GS G 16.0/670
16 - 150 48 30 18 0.09 GS G 16.0/16150
17.2 6 - 95 48 30 18 0.09 GS G 17.2/695 20.0 16 - 95 48 30 18 0.09 GS G 20.0/1695
The aluminium version is mainly used for connecting
aluminium tape to a puddle flange rod as part of a
lightning protection system.
Material: Aluminium with M10 x 25mm Stainless Steel Set Screw.
These clamps are used for joining earth rods
to different sizes of stranded copper
conductor. The clamps have a high resistance
to corrosion and are mechanically strong to
ensure a lasting connection.
Material: High Copper Alloy with M10 x 25mm Phosphor Bronze Set
Screw
* Suitable for use with 8mm Ø solid circular copper conductor.
.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
15
‘U’ BOLT CLAMPS
SINGLE PLATE TYPE FOR HORIZONTAL FLAT TAPES.
Used to connect flat tapes in a horizontal position on the rod
DOUBLE PLATE TYPE FOR VERTICAL FLAT TAPES.
Used to connect flat tapes in a vertical position on the rod
DOUBLE PLATE TYPE FOR VERTICAL STRANDED CABLES.
Used to connect stranded cables in a vertical and horizontal
position on the rod
Maximum Rod Ø mm
Hole Centres mm
L mm
W mm
H mm
Unit Weight kg
Part Number
16 30 58 62 33 0.17 GS ERU S16
25 37 72 62 33 0.19 GS ERU S25
31 41 82 68 33 0.25 GS ERU S31 38 46 90 75 33 0.29 GS ERU S38
50 63 95 90 33 0.39 GS ERU S50
Maximum Rod Ø mm
Tape Width mm
L mm
W mm
H mm
Unit Weight kg
Part Number
16
25
58 62 33 0.23 GS ERU D16 25 73 60 33 0.23 GS ERU D25
31 85 68 33 0.32 GS ERU D31
38 80 75 33 0.34 GS ERU D38
50 103 90 33 0.53 GS ERU D50
Maximum Rod Ø mm
Conductor Range mm2
L mm
W mm
H mm
Unit Weight kg
Part Number
16
16 - 150 57 52 40
0.21 GS ERU 16/470
150 - 300 69 70 0.30 GS ERU 16/570
20
16 - 70 57 52 40
0.21 GS ERU 20/470
70 - 300 69 70 0.30 GS ERU 20/570
25
16 - 70 75 87 55
0.52 GS ERU 25/670
185 - 300 89 70 0.46 GS ERU 25/770
Gansec Shengyuean Provides a comprehensive range of ‘U’ bolt clamps, which can be used to connect flat tapes and stranded cables to earth rods, reinforcing bars (rebar), hand rails etc.
Material: High Copper Alloy plate with M10 threaded Copper ‘U’ Bolt.
Material: High Copper Alloy plates with M10 threaded Copper ‘U’ Bolt.
The ERU470 has an M8 threaded copper ‘U’ bolt.
Material: High Copper Alloy plates with M10 threaded Copper ‘U’ Bolt.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
16
SPLIT CONNECTOR CLAMPS
FOR USE WITH COPPERBOND EARTH
RODS (ON ROD SHANK).
FOR USE WITH SOLID COPPER & STAINLESS
STEEL EARTH RODS (ON ROD SHANK)
FOR USE WITH COPPERBOND EARTH RODS
(ON ROD THREAD)
Rod Shank Ø mm L mm
W mm
H mm
Unit Weight kg
Part Number
9.5 26 16 20 0.07 GS SCC1 10
14.2 42 25 25 0.26 GS SCC1 14
Nominal Rod Size
Thread Size (UNC-2A)
L mm
W mm
H mm
Unit Weight kg
Part Number
5/8 ” 5/8 ” 42 24 26 0.21 GS SCC 16
3/4 ” 3/4 ” 51 31 30 0.34 GS SCC 20
Rod Shank Ø mm L mm
W mm
H mm
Unit Weight kg
Part Number
15 42 26 25 0.21 GS SCC2 15
16 42 25 26 0.21 GS SCC2 16
20 54 29 29 0.23 GS SCC2 20
Split connector clamps are used to connect cable lugs onto earth
rods. The clamps are designed to suit our full range of earth
rods. All clamps are assembled with an M12 x 50mm set screw
and fittings, except ERS010 which has an M8 x 40mm set screw
and fittings. ERC24 also has a wing nut.
Material: High Copper Alloy.
Material: High Copper Alloy.
Material: High Copper Alloy.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
17
‘U’ BOLT CLAMP
This unique specially designed ‘U’ bolt clamp is used to connect
1, 2 or 3 stranded cables to the earth rod. The “V” seat of the
clamp also pushes the earth rod to self-centre itself, which
eliminates any movement in the fitting.
The Clamp is designed for earth rods between 16-20mm
diameters and will accept stranded conductors ranging from
50sqmm to 70sqmm.
UNIVERSAL BEAM CLAMP
This Universal Beam Clamp is a unique product as it is designed to
bond 25x3mm copper tape, 50sqmm and 70sqmm stranded cable as
well as 8mm solid circular conductor to steel beams and RSJ’s of up
to15mm thick.
No other product on the market offers this range of alternatives
when bonding to steel beams and RSJ’s.
Its robust design allows multiple connections without compromise to
the strength or quality.
Maximum Rod Ø mm
Conductor Size mm2
L mm
W mm
H mm
Unit Weight kg Part Number
16 x 20 50 - 70 x 3 72 80 35 0.40 GS ERU 16/20
Conductor Range mm2
Conductor Size mm
L mm
W mm
H mm
H1 mm
Unit Weight kg Part Number
50 - 70 25 x 3 80 43 35 18 0.39 GS UBC 50/70
Material: High Copper Alloy.
Material: High Copper Alloy with Stainless Steel Bolts.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
18
MULTI-PURPOSE ROD TO CABLE & TAPE CLAMP
This has been specifically designed to accommodate copper
tape, stranded copper and copper bonded earth rods and is
primarily used on High Voltage applications.
Rather than use the standard U bolt concept, the GS GTI 5/8
uses a variant that allows the earth rod to self-centre in the
clamp assembly, which reduces the amount of movement in
the fitting.
With the inclusion of slots in the back plate on both plates,
customers have the ability to install the tape either
horizontally or vertically without the need to punch the tape
to accept the fixing bolts.
REBAR CLAMPS
This versatile range of Rebar clamps are used to
connect rebar to rebar or rebar to stranded cable.
They provide a strong mechanical connection along
with excellent resistance to corrosion.
Maximum Rebar Ø mm
Rebar Range Ø mm
L mm
W mm
Unit Weight kg
Part Number
10 6 - 10 59 60 0.21 GS RBC 10
20 12 - 20 83 62 0.36 GS RBC 20
25 20 - 25 100 67 0.42 GS RBC 25
32 25 - 32 101 80 0.60 GS RBC 32
40 32 - 40 118 95 0.70 GS RBC 40
Maximum Rod Ø mm
Conductor
Range mm2
Conductor Size mm
L mm
W mm
H mm
Unit Weight kg
Part Number
5/8 ” 6 - 185 25 x 4 72 83 66 0.55 GS GTI 5/8
Material: High Copper Alloy plates with M10 threaded Copper ‘U’ Bolt.
Material: High Copper Alloy plates with Copper ‘U’ Bolt.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
19
REBAR X CLAMP
A heavy duty rebar clamp designed specifically to
connect a vertical rebar to a horizontal rebar in a
cross configuration. This product provides a
strong mechanical connection along with excellent resistance to corrosion.
STAINLESS STEEL REBAR CLAMPS
Gansec Shengyuean provides a versatile range of Rebar
Clamps, which are used to connect rebar-rebar or Rebar-
conductor.
They provide a strong mechanical connection along with
excellent resistance to corrosion. These items are made
from stainless steel and are simple to install.
Maximum Rebar Ø mm
Rebar Range Ø mm
L mm
W mm
Unit Weight kg Part Number
12 8 - 12 50 22 0.05 GS RBS 12
16 16 - 16 59 22 0.05 GS RBS 16
20 20 - 20 68 26 0.06 GS RBS 20
25 25 - 25 81 31 0.07 GS RBS 25
32 32 - 32 98 39 0.07 GS RBS 32 40 40 - 40 120 48 0.08 GS RBS 40
Maximum Rebar Ø mm
Rebar Range Ø mm
L mm
W mm
Unit Weight kg Part Number
25 12 - 25 91 75 0.52 GS RBXC 25
Material: High Copper Alloy Plates with Stainless Steel ‘C’ Bolt.
Material: Stainless Steel.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
20
Pipe Diameter Conductor Range mm2
Unit Weight kg Part Number
½” - 1” (13 - 25mm) 25 - 95 0.03 GS PC 25
1 ¼” - 2” (32 - 50mm) 25 - 95 0.04 GS PC 50 2 ½” - 3 ½” (65 - 90mm) 25 - 95 0.08 GS PC 90
4” - 5” (100 - 125mm) 25 - 95 0.06 GS PC 125
6” (150mm) 25 - 95 0.08 GS PC 150
8” (200mm) 25 - 95 0.10 GS PC 200
10” (250mm) 25 - 95 0.11 GS PC 250
12” (300mm) 25 - 95 0.15 GS PC 300
L x W mm
H mm
Surface Area m2 Unit Weight kg Part Number
600 x 600
1.5 0.73 4.80 GS EP 600/15
3.0 9.60 GS EP 600/30
900 x 900
1.5 1.63
10.80 GS EP 900/15
3.0 21.60 GS EP 900/30
1000 x 500
5.0 1.02 GS EP 1000/50
PIPE CLAMPS
These heavy duty pipe clamps are ideal for bonding and
connecting cable conductor to large diameter pipework’s.
They are suitable for use with copper, steel or stainless steel
pipes
Available in aluminium on request
SOLID COPPER EARTH PLATES
The Solid copper plates provide a long lasting earthing
solution
In places where driving earth rods might be impractical.
They are often installed in conjunction with Low-
Resistance Earthing Compound or Bentonite.
Material: Copper to BS EN 1652:1998.
Material: Tinned bronze.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
21
L x W mm
H mm
Surface Area m2 Grid Unit Weight kg Part Number
600 x 600
3.0 0.31 5 Bar 4.00 GS LM 600/31
900 x 900
3.0
0.65 6 Bar 7.20 GS LM 900/65
0.46 6 Bar 6.10 GS LM 900/46
L x W mm
H mm
Surface Area m2 Grid Unit Weight kg Part Number
600 x 600
3.0
0.31 5 Bar 6.10 GS LMS 600/31
0.55 10 Bar - GS LMS 600/55
900 x 900
3.0
0.65 6 Bar 7.30 GS LMS 900/65
0.89 10 Bar - GS LMS 900/89
900 x 900
5.0 0.56 6 Bar - GS LMS 900/56
SOLID COPPER LATTICE MATS
The Solid copper lattice mats offer a more economical cost
option to installing solid copper plates
They are often used for potential grading and are a
preferred option on installations such as telecommunication
towers, where touch and step potential could cause
problems.
Material: Copper to BS EN 13601 (formerly BS 1432).
STAINLESS STEEL LATTICE MATS
The Stainless Steel Lattice Mats, manufactured from Stainless
Steel 316 Grade, are used in areas where a high corrosive
environment is present.
They are often used for potential grading and are preferred
option on installations such as telecommunication towers,
where touch and step potential could cause problems.
Material: Stainless Steel to SS316 Grade and SS316 Rivets.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
22
Conductor Range mm2 L mm
W mm
H mm
Set Screw Unit Weight kg Part Number
16 - 70 45 30 17 M10 x 50mm 0.12 GS TC 70
70 - 120 48 35 22 M12 x 60mm 0.23 GS TC 120 120 - 185 55 40 28 M12 x 75mm 0.30 GS TC 185
185 - 240 63 45 35 M12 x 80mm 0.40 GS TC 240
240 - 300 70 53 42 M12 x 90mm 0.60 GS TC 300
Conductor Range mm2
L mm
W mm
H mm
Set Screw Unit Weight kg Part Number
25 - 70 50 40 7 M8 x 35mm 0.38 GS PG 70
70 - 95 54 45 8.5 M10 x 45mm 0.46 GS PG 95
95 - 185 65 57 12.5 M10 x 55mm 0.55 GS PG 185 185 - 240 78 71 14 M10 x 55mm 0.66 GS PG 240
240 - 300 94 85 16 M10 x 60mm 0.78 GS PG 300
TOWER EARTH CLAMPS
Tower earth clamps are used for bonding copper conductors onto steel
surfaces.
The double-plate design provides a robust fixing in areas where
cladding may be installed or where the complete clamp will be covered
by concrete. The clamp is fixed by drilling a hole in the steelwork and
securing with the set screw provided.
PARALLEL GROOVE CLAMPS
The Parallel Groove Clamps, for the stranded
copper cable connections, are manufactured from
high-strength, corrosion-resistant copper alloy and
assembled with two stainless steel set screws.
Material: High Copper Alloy
Material: High Copper Alloy
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
23
No. Holes Hole Size mm
Plate Size mm
Stem Ø mm
L mm
Unit Weight kg
Part Number
1 M10 x 18
38 x 38 10.7
(70mm2)
75
0.14 GS EBP 01
2 70 x 35 0.29 GS EBP 02
4
63 x 63 0.54 GS EBP 04
M8 x 1.25 100 x 100 73 - GS EBP 04/8
No. Holes Type Unit Weight kg
Part Number
1
EBP 01 with pre-welded 500mm long tail of 70mm2 PVC insulated cable
0.64
GS EBP 15
2
EBP 02 with pre-welded 500mm long tail of 70mm2 PVC insulated cable
0.77
GS EBP 25
EBP 02 with pre-welded 1000mm long
tail of 70mm2 PVC insulated cable
1.14
GS EBP 21
EBP 02 with pre-welded 1500mm long
tail of 70mm2 PVC insulated cable
1.50
GS EBP 215
4
EBP 04 with pre-welded 500mm long tail of 70mm2 PVC insulated cable
1.02
GS EBP 45
EBP 04 with pre-welded 1000mm long
tail of 70mm2 PVC insulated cable
1.39
GS EBP 41
EBP 04 with pre-welded 1500mm long
tail of 70mm2 PVC insulated cable
1.75
GS EBP 415
EARTH BONDING POINTS
The earth bonding points are installed to provide a
convenient earth system connection point in concrete
structures. When cast into concrete they connect the re-
bar to the earthing or lightning protection system.
EARTH BONDING POINTS ONLY
EARTH BONDING POINTS WITH PRE-WELDED TAILS
Material: High Copper Alloy
Material: High Copper Alloy body with PVC insulated copper cable tail.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
24
No. Holes Type Unit Weight kg Part Number
1
EBP 01 with 2 x pre-welded 500mm
long tails of 70mm2 PVC insulated cable
0.93
GS EBP 125
2
EBP 02 with 2 x pre-welded 500mm
long tails of 70mm2 PVC insulated cable
1.08
GS EBP 225
EBP 02 with 2 x pre-welded 1000mm
long tails of 70mm2 PVC insulated cable
1.81
GS EBP 221
EBP 02 with 2 x pre-welded 1500mm
long tails of 70mm2 PVC insulated cable
2.54
GS EBP 2215
4
EBP 04 with 2 x pre-welded 500mm
long tails of 70mm2 PVC insulated cable
1.33
GS EBP 425
EBP 04 with 2 x pre-welded 1000mm
long tails of 70mm2 PVC insulated cable
2.06
GS EBP 421
EBP 04 with 2 x pre-welded 1500mm
long tails of 70mm2 PVC insulated cable
2.79
GS EBP 4215
EARTH BONDING POINTS WITH DOUBLE PRE-WELDED TAILS
Material: High Copper Alloy body with 2 x PVC insulated copper cable tails.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
25
No. Holes Type Unit Weight kg Part Number
1 EBP 01 with a front plate 0.24 GS EBPF 01
2 EBP 02 with a front plate 0.39 GS EBPF 02
4 EBP 04 with a front plate 0.64 GS EBPF 04
No. Holes Type Unit Weight kg Part Number
1 EBP 01 500 with a front plate 0.77 GS EBPF 15
2
EBP 02 500 with a front plate 0.90 GS EBPF 25
EBP 02 1000 with a front plate
1.27 GS EBPF 21
EBP 02 1500 with a front plate
1.63 GS EBPF 215
4
EBP 04 500 with a front plate 1.15 GS EBPF 45
EBP 04 1000 with a front plate
1.52 GS EBPF 41
EBP 04 1500 with a front plate
1.88 GS EBPF 415
EARTH BONDING POINTS WITH A FRONT PLATE
Suitable for 25x3mm tape or 70mm2 cable.
Material: High Copper Alloy.
EARTH BONDING POINTS WITH A PRE-WELDED TAIL & FRONT PLATE
Suitable for 25x3mm tape or 70mm2 cable.
Material: High Copper Alloy with PVC Insulated Copper Cable Tail.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
26
No. Holes Type Unit Weight kg Part Number 1 EBP 01 2 with a front plate 1.09 GS EBPF 12
2
EBP 02 2 with a front plate 1.24 GS EBPF 22
EBP 021 2 with a front plate 1.97 GS EBPF 212
EBP 025 2 with a front plate 2.70 GS EBPF 252
4
EBP 04 2 with a front plate 1.49 GS EBPF 42
EBP 041 2 with a front plate 2.24 GS EBPF 412
EBP 045 2 with a front plate 2.95 GS EBPF 452
EARTH BONDING POINTS WITH 2 X PRE-WELDED TAILS &
FRONT PLATE
Suitable for 25x3mm tape or 70mm2 cable.
Material: High Copper Alloy with 2 x PVC Insulated Copper Cable Tails.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
27
No Terminations L mm
W mm
H mm
Unit Weight kg Part Number
2 200
90
60
1.00 GS EB 22
3 250 1.22 GS EB 325
4 300 1.45 GS EB 43
6 400 2.00 GS EB 64
8 500 2.30 GS EB 85
9 600 2.75 GS EB 96 10 650 3.20 GS EB 1065
12 750 4.00 GS EB 1275
14 850 4.90 GS EB 1485
16 950 5.80 GS EB 1695
18 1100 6.70 GS EB 1811
20 1250 7.60 GS EB 20125
22 1300 8.50 GS EB 2213 24 1400 9.40 GS EB 2414
26 1550 10.30 GS EB 26155
28 1650 11.20 GS EB 28165
30 1800 12.10 GS EB 3018
EARTH BARS
The earth bars provide a convenient common earthing point for
electrical installations. Gansec Shengyuean standard earth bars are
manufactured from 50mm x 6mm hard drawn copper bar and come
complete with M10 fittings and insulators. The PVC base makes our
earth bars lighter and easier to handle as well as being entirely
corrosion proof
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
EARTH BARS
Material:
Bar: 50 x 6mm hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
28
No Terminations L mm
W mm
H mm
Unit Weight kg
Part Number
2 200
90
60
1.00 GS EBT 22
3 250 1.22 GS EBT 325
4 300 1.45 GS EBT 43
6 400 2.00 GS EBT 64
8 500 2.30 GS EBT 85
9 600 2.75 GS EBT 96
10 650 3.20 GS EBT 1065 12 750 4.00 GS EBT 1275
14 850 4.90 GS EBT 1485
16 950 5.80 GS EBT 1695
18 1100 6.70 GS EBT 1811
20 1250 7.60 GS EBT 20125
22 1300 8.50 GS EBT 2213
24 1400 9.40 GS EBT 2414 26 1550 10.30 GS EBT 26155
28 1650 11.20 GS EBT 28165
30 1800 12.10 GS EBT 3018
Tinned Earth Bars
The tinned earth bars have been used on a variety of high-profile
projects, this is partly due to the fact that our tinned earth bars offer
excellent resistance to water corrosion, and subsequently provide
enhanced conductivity. The tinning process means that copper bars
are protected from oxidisation. Gansec Shengyuean tinned earth
bars have a typical copper purity content in excess of 99.9%.
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
Tinned Earth Bars
Material:
Bar: 50 x 6mm tinned hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
29
No Terminations L mm
W mm
H mm
Unit Weight kg
Part Number
2 285
90
60
1.55 GS EBS 2285
3 330 1.77 GS EBS 333
4 375 2.00 GS EBS 4375 6 475 2.50 GS EBS 6475
8 575 3.00 GS EBS 8575
9 685 3.45 GS EBS 9685
10 725 3.90 GS EBS 10725
12 825 4.70 GS EBS 12825
14 925 5.60 GS EBS 14925
16 1025 6.50 GS EBS 161025 18 1175 7.40 GS EBS 181175
20 1325 8.30 GS EBS 201325
22 1375 9.20 GS EBS 221375
24 1475 10.10 GS EBS 241475
26 1625 11.00 GS EBS 261625
28 1725 11.90 GS EBS 281725
30 1875 12.80 GS EBS 301875
EARTH BARS WITH SINGLE DISCONNECTING LINK
Gansec Shengyuean earth bars provide a convenient common earthing point for electrical installations. Our standard earth bars are manufactured from 50mm x 6mm hard drawn copper bar and come complete with M10 fittings and insulators. The PVC base makes our earth bars lighter and easier to handle as well as being entirely corrosion proof. All earth bars have a typical copper purity content in excess of 99.9%.
The Gansec Shengyuean single disconnecting link earth bars are mainly used to offer a temporary break in the connection to the earth, allowing the inspection and testing of multiple earth rods / systems while disconnected from the lightning and earth system.
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
Earth Bars with Single Disconnecting Link
Material:
Bar: 50 x 6mm hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
30
No Terminations L mm
W mm
H mm
Unit Weight kg Part Number
2 285
90
60
1.55 GS EBTS 2285
3 330 1.77 GS EBTS 333
4 375 2.00 GS EBTS 4375
6 475 2.50 GS EBTS 6475
8 575 3.00 GS EBTS 8575
9 685 3.45 GS EBTS 9685 10 725 3.90 GS EBTS 10725
12 825 4.70 GS EBTS 12825
14 925 5.60 GS EBTS 14925
16 1025 6.50 GS EBTS 161025
18 1175 7.40 GS EBTS 181175
20 1325 8.30 GS EBTS 201325
22 1375 9.20 GS EBTS 221375 24 1475 10.10 GS EBTS 241475
26 1625 11.00 GS EBTS 261625
28 1725 11.90 GS EBTS 281725
30 1875 12.80 GS EBTS 301875
TINNED EARTH BARS WITH SINGLE DISCONNECTING LINK
These tinned earth bars have been used on a variety of high-profile projects, this is partly due to the fact that our tinned earth bars offer excellent resistance to water corrosion, and subsequently provide enhanced conductivity. The tinning process means that copper bars are protected from oxidisation. Our tinned earth bars have a typical copper purity content in excess of 99.9%.
The Gansec Shengyuean single disconnecting link tinned earth bars are mainly used to offer a temporary break in the connection to the earth, allowing the inspection and testing of multiple earth rods / systems while disconnected from the lightning and earth system.
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
Tinned Earth Bars with Single Disconnecting Link
Material:
Bar: 50 x 6mm tinned hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
31
No Terminations L mm
W mm
H mm
Unit Weight kg Part Number
2 350
90
60
2.10 GS EBD 235
3 400 2.32 GS EBD 34
4 450 2.55 GS EBD 445
6 550 3.10 GS EBD 655
8 650 3.70 GS EBD 865 9 725 4.10 GS EBD 9725
10 800 4.50 GS EBD 108
12 900 5.30 GS EBD 129
14 1000 6.20 GS EBD 141
16 1100 7.10 GS EBD 1611
18 1250 8.00 GS EBD 18125
20 1400 8.90 GS EBD 2014 22 1450 10.50 GS EBD 22145
24 1550 10.70 GS EBD 24155
26 1700 11.60 GS EBD 2617
28 1800 12.50 GS EBD 2818
30 1950 13.40 GS EBD 30195
EARTH BARS WITH DOUBLE DISCONNECTING LINKS The earth bars provide a convenient common earthing point for electrical installations. Our standard earth bars are manufactured from 50mm x 6mm hard drawn copper bar and come with M10 fittings and insulators. The PVC base makes ours earth bars lighter and easier to handle as well as being entirely corrosion proof. All earth bars have typical copper purity content in excess of 99.9%.
The Gansec Shengyuean double disconnecting link earth bars are mainly used to offer a temporary break in the connection to the earth, allowing the inspection and testing of multiple earth rods / systems while disconnected from the lightning and earth system.
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
Earth Bars with Double Disconnecting Link
Material:
Bar: 50 x 6mm hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
32
No Terminations L mm
W mm
H mm
Unit Weight kg Part Number
2 350
90
60
2.10 GS EBTD 235
3 400 2.32 GS EBTD 34
4 450 2.55 GS EBTD 445
6 550 3.10 GS EBTD 655
8 650 3.70 GS EBTD 865
9 725 4.10 GS EBTD 9725
10 800 4.50 GS EBTD 108 12 900 5.30 GS EBTD 129
14 1000 6.20 GS EBTD 141
16 1100 7.10 GS EBTD 1611
18 1250 8.00 GS EBTD 18125
20 1400 8.90 GS EBTD 2014
22 1450 10.50 GS EBTD 22145
24 1550 10.70 GS EBTD 24155 26 1700 11.60 GS EBTD 2617
28 1800 12.50 GS EBTD 2818
30 1950 13.40 GS EBTD 30195
TINNED EARTH BARS WITH DOUBLE DISCONNECTING LINKS
The tinned earth bars are used for a variety of high-profile projects, this is partly due to the fact that our tinned earth bars offer excellent resistance to water corrosion, and subsequently provide enhanced conductivity. The tinning process means that copper bars are protected from oxidisation. Our tinned earth bars have a typical copper purity content in excess of 99.9%.
The Gansec Shengyuean double disconnecting link tinned earth bars are mainly used to offer a temporary break in the connection to the earth, allowing the inspection and testing of multiple earth rods / systems while disconnected from the lightning and earth system.
Special earth bars manufactured to customer requirements are also available.
Recommended fixing by countersunk wood screw 1 ½” x No. 12 and No. 12 wall Plug.
Tinned Earth Bars with Double Disconnecting Link
Material:
Bar: 50 x 6mm tinned hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
33
Type Thread Size
W mm
H mm
Unit Weight kg Part Number
Insulator
M10 40 40 0.08 GS EBI 4040
M10 40 - - GS EBI 40
M6 18 20 - GS EBI 1820
M6 32 30 - GS EBI 3230
M8 38 40 - GS EBI 3840
M10 46 50 - GS EBI 4650
M10 50 60 - GS EBI 5060
M12 55 70 - GS EBI 5570
L mm
W mm
H mm
Unit Weight kg Part Number
120 45 45 0.60 GS DL 120
DISCONNECTING LINK The disconnecting link provides a temporary break in the earth connection to allow inspection and testing of the earth electrode.
Material:
Bar: 50 x 6mm hard drawn copper bar to BS EN 13601.
Base: Plastic.
Fittings: M10 Hexagon Head Set Screws, Nuts & Washers.
INSULATORS
These Wallis insulators are supplied with or without studs and locking nuts.
Material: Reinforced Polyester with brass fittings.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
34
Type L mm
W mm
H mm
Unit Weight kg Part Number
4-Way Single 54 9 12
0.06 GS EBS 4 4-Way Double 51 18 0.09 GS EBD 4
8-Way Double 88 18 0.15 GS EBD 8
D mm
L mm
Thread Size Unit Weight kg Part Number
25 25 M8 0.11 GS EB 25258
30 30 M8 0.18 GS EB 30308
30 30 M10 0.20 GS EB 303010
30 40 M10 0.33 GS EB 304010
30 40 M12 0.36 GS EB 304012
30 50 M10 0.50 GS EB 305010 30 50 M12 0.52 GS EB 305012
40 30 M8 0.24 GS EB 40308
40 30 M10 0.35 GS EB 403010
40 40 M10 0.43 GS EB 404010
40 40 M12 0.45 GS EB 404012
40 50 M10 0.65 GS EB 405010
40 50 M12 0.67 GS EB 405012 50 30 M8 0.29 GS EB 50308
50 30 M10 0.31 GS EB 503010
50 40 M10 0.53 GS EB 504010
50 40 M12 0.55 SGS EB 504012
50 50 M10 0.80 GS EB 505010
50 50 M12 0.80 GS EB 505012
EARTH BLOCKS The blocks allow earth conductor termination, or live conductor termination with a suitable, fully insulated housing
EARTH BOSSES The earth boss is designed to provide an earth connection point on a steel structure. The boss is welded onto steel vessels, tanks and other structures. Wrap connections with Denso tape.
Material: Mild Steel with Stainless Steel fittings.
Material: Tinned Brass
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
35
D mm
L mm
Thread Size Unit Weight kg Part Number
25 25 M8 0.11 GS EBS 25258 30 30 M8 0.18 GS EBS 30308
30 30 M10 0.20 GS EBS 303010
30 40 M10 0.33 GS EBS 304010
30 40 M12 0.36 GS EBS 304012
30 50 M10 0.50 GS EBS 305010
30 50 M12 0.52 GS EBS 305012
40 30 M8 0.24 GS EBS 40308 40 30 M10 0.35 GS EBS 403010
40 40 M10 0.43 GS EBS 404010
40 40 M12 0.45 GS EBS 404012
40 50 M10 0.65 GS EBS 405010
40 50 M12 0.67 GS EBS 405012
50 30 M8 0.29 GS EBS 50308
50 30 M10 0.31 GS EBS 503010 50 40 M10 0.53 GS EBS 504010
50 40 M12 0.55 GS EBS 504012
50 50 M10 0.80 GS EBS 505010
50 50 M12 0.80 GS EBS 505012
STAINLESS STEEL EARTH BOSSES The stainless steel earth boss is designed to provide an earth connection point on a stainless steel structure. The boss is welded onto stainless steel vessels, tanks and other stainless steel structures. Wrap connections with Denso tape.
Material: Stainless Steel body & Stainless Steel fittings.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
36
Main Conductor A
mm2
Tap Conductor B
mm2
H mm
W mm
Unit Weight kg Part Number
10 1.5 - 10 20 4 0.02 GS SBC 10
16 2.5 - 16 23 5 0.03 GS SBC 16
25 2.5 - 25 28 7 0.04 GS SBC 25
35 2.5 - 35 29 8 0.05 GS SBC 35 50 2.5 - 50 35 10 0.08 GS SBC 50
70 2.5 - 70 39 11 0.12 GS SBC 70
95 2.5 - 95 45 14 0.15 GS SBC 95
120 10 - 120 47 15 0.18 GS SBC S120
150 10 - 150 51 16 0.23 GS SBC 150
185 50 - 185 57 18 0.35 GS SBC 185
240 95 - 240 64 19 0.46 GS SBC 240
D mm
L mm
Thread Size Unit Weight kg Part Number
40 125 M12 0.75 GS SCC 40
SPLIT BOLT CONNECTORS The high strength split bolt connectors will accept a wide range of stranded copper conductors. No specialist tools are required for installation.
Material: High Copper Alloy.
HV SURGE COUNTER COUPLING The HV Surge counter coupling (GS SCC 001) is used in conjunction with the Siemens Surge Counter to allow a convenient connection between the surge counter and the conductor it is being connected to.
This assembly is usually installed on High Voltage Substations as part of the High Frequency earthing arrangement. One assembly will be installed per phase at cable sealing ends and other parts of the system where HV surges to earth are to be monitored. This is to be installed generally in line with National Grid Specification TS 3.1.2
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
37
Size W x H mm
Hole Centres L mm
Hole Size mm Unit Weight kg Part Number
10 x 2
100
6
0.01 GS FCB 1021
200 0.01 GS FCB 1022
300 0.01 GS FCB 1023
12 x 2
100 0.01 GS FCB 121
200 0.01 GS FCB 122
300 0.02 GS FCB 123
19 x 2.5
100
10
0.01 GS FCB 191
200 0.03 GS FCB 192
300 0.05 GS FCB 193
25 x 3 100 0.02 GS FCB 2531
200 0.05 GS FCB 2532
400 0.10 GS FCB 2534
25 x 3.5
200 11
0.09 GS FCB 200
300 0.13 GS FCB 300
400 0.16 GS FCB 400
30 x 4.5
200
10
0.10 GS FCB 302
400 0.20 GS FCB 304
32 x 5 200 0.14 GS FCB 322
400 0.28 GS FCB 324
FLEXIBLE COPPER BRAID BONDS The flexible copper braid bonds are used for bonding metal gates, doors, fences etc. Other lengths and sizes are available on request.
Material: Copper
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
38
Size W x H mm
Hole Centres L mm
Hole Size mm Unit Weight kg Part Number
10 x 2
100
6
0.01 GS FCBT 1021
200 0.01 GS FCBT 1022
300 0.01 GS FCBT 1023
12 x 2
100 0.01 GS FCBT 1221
200 0.01 GS FCBT 1222
300 0.02 GS FCBT 1223
19 x 2.5 100
10
0.01 GS FCBT 1921
200 0.03 GS FCBT 1922
300 0.05 GS FCBT 1923
25 x 3
100 0.02 GS FCBT 2531
200 0.05 GS FCBT 2532
400 0.10 GS FCBT 2534
25 x 3.5
200 11
0.09 GS FCBT 2532
300 0.13 GS FCBT 2533
400 0.16 GS FCBT 2534
30 x 4.5 200
10
0.10 GS FCBT 3042
400 0.20 GS FCBT 3044
32 x 5
200 0.14 GS FCBT 3252
400 0.28 GS FCBT 3254
TINNED FLEXIBLE COPPER BRAID
BONDS
The flexible copper braid bonds are used for bonding metal gates, doors, fences etc. Other lengths and sizes are available on request.
Material: Tinned Copper
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
39
Nominal Area mm2
Hole Centres L mm
Hole Size mm
Unit Weight kg Part Number
4
100
M6
0.01 GS FCB 41
200 0.01 GS FCB 42
300 0.01 GS FCB 43
6
100 0.01 GS FCB 61
200 0.01 GS FCB 62
300 0.02 GS FCB 63
10
100 0.01 GS FCB 101
200 0.02 GS FCB 102
300 0.03 GS FCB 103
16
100 0.01 GS FCB 161
200 0.03 GS FCB 162
300 0.05 GS FCB 163
100
M10
0.01 GS FCB 161
200 0.03 GS FCB 162
300 0.05 GS FCB 163
25
200 0.03 GS FCB 252
400 0.05 GS FCB 254
35
200 0.07 GS FCB 352
400 0.14 GS FCB 354
50
200 0.10 GS FCB 502
400 0.20 GS FCB 504
70
200 0.14 GS FCB 702
400 0.28 GS FCB 704
FLEXIBLE CIRCULAR COPPER BRAID
BONDS
The flexible circular copper braid bonds are used for bonding metal gates, doors, fences etc. Other lengths and sizes are available on request.
Material: Copper
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
40
Nominal Area mm2 Hole Centres L mm
Hole Size mm Unit Weight kg Part Number
4
100
M6
0.01 GS FCBT 41
200 0.01 GS FCBT 42
300 0.01 GS FCBT 43
6
100 0.01 GS FCBT 61
200 0.01 GS FCBT 62
300 0.02 GS FCBT 63
10 100 0.01 GS FCBT 101
200 0.02 GS FCBT 102
300 0.03 GS FCBT 103
16
100 0.01 GS FCBT 161
200 0.03 GS FCBT 162
300 0.05 GS FCBT 163
100
M10
0.01 GS FCBT 161
200 0.03 GS FCBT 162
300 0.05 GS FCBT 163
25
200 0.03 GS FCBT 252
400 0.05 GS FCBT 254
35 200 0.07 GS FCBT 352
400 0.14 GS FCBT 354
50
200 0.10 GS FCBT 502
400 0.20 GS FCBT 504
70
200 0.14 GS FCBT 702
400 0.28 GS FCBT 704
TINNED FLEXIBLE CIRCULAR COPPER
BRAID BONDS
The tinned flexible copper braid bonds are used for bonding metal gates, doors, fences etc. Other lengths and sizes are available on request.
Material: Tinned Copper
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
41
H
mm D
mm Unit Weight kg Part Number
135 125 3.00 GS SER 135
L mm
H mm
Unit Weight kg Part Number
350 100 1.52 GS SEB 35
200 250 - GS SEB 20
Thread Size H mm
Unit Weight kg Part Number
5/8 ” 135
0.62 GS EB 58
3/4 ” 0.55 GS EB 34
STATIC EARTH RECEPTACLE
The receptacle is used in open areas where a temporary earthing point may be required, such as airfields or petrol stations. Provides a static discharge point for aircraft tankers, vehicles and boats.
EYEBOLTS
Provides a static earth point when attached to the top of a threaded copperbond earth rod.
STATIC EARTH BAR
This wall-mounted bracket provides a temporary earth point.
Material: High Copper Alloy.
Material: High Copper Alloy.
Material: Phosphor Bronze.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
42
Main Conduct
or A mm2
Tap Conductor B mm2
L mm
W mm
H mm
Unit Weight kg Part Number
10 4 - 10 13 12 9 0.01 GS CC 10
10 - 16 10 - 16 19 17 12 0.01 GS CC 16
16 4 19 17 12 0.01 GS CC 164
16 - 25 1.5 - 10 20 12 13 0.02 GS CC 251
25 10 - 16 21 19 12 0.02 GS CC 2516
25 10 - 25 24 20 15 0.04 GS CC 2525
35 1.5 - 16 24 20 15 0.04 GS CC 3516 35 25 - 35 27 20 15 0.05 GS CC 3535
50 4 - 16 27 20 15 0.05 GS CC 5016
50 16 - 50 27 20 17 0.07 GS CC 5050
70 1.5 - 25 27 20 17 0.07 GS CC 7025
50 - 70 4 - 35 33 28 21 0.09 GS CC 7035
50 - 70 35 - 70 34 28 21 0.10 GS CC 7070
70 - 95 35 - 70 41 30 26 0.10 GS CC 9570 95 4 - 35 41 30 26 0.11 GS CC 9535
70 - 95 95 41 30 26 0.12 GS CC 9595
120 35 - 120 45 30 28 0.12 GS CC 120120
150 6 - 70 45 30 28 0.12 GS CC 15070
150 95 - 150 45 30 28 0.15 GS CC 150150
120 - 185 95 - 185 54 35 33 0.20 GS CC 185185
150 - 185 70 - 150 54 35 33 0.20 GS CC 185150 240 10 - 70 - - - - GS CC 24070
240 95 - 120 54 37 34 0.24 GS CC 240120
240 150 - 240 54 40 43 0.24 GS CC 240240
‘C’ CRIMP CONNECTORS
The ‘C’ Crimp Connectors are specifically designed for tap and parallel connections of stranded copper cables in earthing applications.
Material: Copper.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
43
COMPRESSION CABLE LUGS
Gansec Shengyuean High performance cable lugs are formed using
copper tube for cables up to 500mm² and chamfered entry for
cables 500mm² to 1000mm². All lugs are subjected to through
manufacturing processes to avoid damages during crimping
process, for which there is also an inspection hole to enable cable
location verification prior to crimping. The lugs are electro-tin
plated to combine maximum electrical conductivity with
mechanical strength.
SINGLE HOLE COMPRESSION CABLE LUGS
Conducto
r Size mm2
Palm Hole Size mm
L mm
W mm
Unit Weight kg Part Number
6
4 21 9
0.01
GS CLG 64 5 24 10 GS CLG 65 6 24 11 GS CLG 66 8 25 12 GS CLG 68
10 26 12 GS CLG 610
10
5 26 11
0.01
GS CLG 105 6 26 11 GS CLG 106 8 29 13 GS CLG 108
10 39 16 GS CLG 1010 12 39 18 GS CLG 1012
16
6 30 11
0.01
GS CLG 166 8 30 13 GS CLG 168
10 35 15 GS CLG 1610 12 42 18 GS CLG 1612
25
6 32 14
0.01
GS CLG 256 8 32 14 GS CLG 258
10 38 16 GS CLG 2510 12 38 18 GS CLG 2512
35
6 35 15
0.01
GS CLG 356 8 35 15 GS CLG 358
10 40 15 GS CLG 3510 12 40 18 GS CLG 3512
14 43 20 GS CLG 3514
50
6 37 17
0.02
GS CLG 506 8 37 17 GS CLG 508
10 42 17 GS CLG 5010 12 42 17 GS CLG 5012 14 45 20 GS CLG 5014
70
6 40 21
0.04
GS CLG 706 8 40 21 GS CLG 708
10 46 21 GS CLG 7010 12 46 21 GS CLG 7012 14 50 21 GS CLG 7014 16 50 21 GS CLG 7016
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
44
SINGLE HOLE COMPRESSION CABLE LUGS (Continued)
9
Material: Tin Plated Copper
Conductor Size mm2
Palm Hole Size mm
L mm
W mm
Unit Weight kg Part Number
95
6 47 25
0.06
GS CLG 956 8 49 25 GS CLG 958
10 49 25 GS CLG 9510 12 49 25 GS CLG 9512 14 56 25 GS CLG 9514 16 56 25 GS CLG 9516
120
8 50 27
0.07
GS CLG 1208 10 56 27 GS CLG 12010 12 56 27 GS CLG 12012 14 56 27 GS CLG 12014 16 60 27 GS CLG 12016 20 66 27 GS CLG 12020
150
8 66 30
0.09
GS CLG 1508 10 68 30 GS CLG 15010 12 68 30 GS CLG 15012 14 68 30 GS CLG 15014 16 70 30 GS CLG 15016 20 75 30 GS CLG 15020
185
10 67 33
0.10
GS CLG 18510 12 68 33 GS CLG 18512 14 68 33 GS CLG 18514 16 70 33 GS CLG 18516 20 75 33 GS CLG 18520
240
10 88 38
0.14
GS CLG 24010 12 88 38 GS CLG 24012 14 88 38 GS CLG 24014 16 88 38 GS CLG 24016 20 88 38 GS CLG 24020
300
10 97 41
0.17
GS CLG 30010 12 97 41 GS CLG 30012 14 97 41 GS CLG 30014 16 97 41 GS CLG 30016 20 97 41 GS CLG 30020
400
12 108 47
0.20
GS CLG 40012 14 108 47 GS CLG 40014 16 108 47 GS CLG 40016 20 108 47 GS CLG 40020
500
16 117 53
0.50
GS CLG 50016 18 117 53 GS CLG 50018 20 117 53 GS CLG 50020
630
16 127 63
0.80
GS CLG 63016 18 127 63 GS CLG 63018 20 127 63 GS CLG 63020
800
16 164 70
1.00
GS CLG 80016 18 164 70 GS CLG 80018 20 164 70 GS CLG 80020
1000
18 164 77 1.30
GS CLG 100018 20 164 77 GS CLG 100020
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
45
CABLE MM²
Ø E ALL DIMENSION IN MM PART NUMBER
A C D G P B L 16 10.5 5.4 7.1 15 40 64 15 84 GS CLG 1610
25 10.5 6.8 8.8 18 40 64 15 87 GS CLG 2510 35 10.5 8.2 10.6 18 40 66 17 90 GS CLG 3510
50 13 9.5 12.4 22.5 40 66 27.5 102 GS CLG 5013
70 13 11.2 14.7 24 40 67 30 107 GS CLG 7013
95 13 13.5 17.4 26 40 67 33 111 GS CLG 9513
120 13 15 19.4 28 40 70 36 118 GS CLG 12013
150 13 16.5 21.2 31 40 72 44 130 GS CLG 15013
185 13 18.5 23.5 35 40 76 55 149 GS CLG 18513 240 13 21 26.5 38 40 78 55 150 GS CLG 24013
300 13 23.5 30 42 40 78 55 160 GS CLG 30013
COMPRESSION TYPE TWO HOLE TIN PLATED COPPER CABLE LUGS
Features: With/Without Inspection Hole
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
46
S
WIRE SIZE ALL DIMENSION IN MM PART NUMBER MCM COPPER
CONDUCTOR CROSS SECTION AREA OF CABLE
D
F
B
H
P
G
L
350 185 M14 17.6 100 44.4 44.4 100 173 GS CLG 18514
500 240 M14 21 76.2 45 45 80 171 GS CLG 24014 600 300 M14 23 76.2 45 45 80 171 GS CLG 30014
800 400 M14 26.5 76.2 45 45 80 177 GS CLG 40014
1000 500 M14 29.3 76.5 45 45 80 183 GS CLG 50014
1250 630 M14 33 76.5 44.5 44.5 76.5 176.5 GS CLG 63014
2000 1000 M14 41.7 77.8 45 45 79 207 GS CLG 100014
COMPRESSION TYPE FOUR HOLE TIN PLATED COPPER CABLE LUGS (MV)
Application: 0.6KV to 36KV
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
47
WIRE SIZE ALL DIMENSION IN MM PART NUMBER MCM COPPER CONDUCTOR
CROSS SECTION AREA OF CABLE
D
F
B
H
P
A
L
600 300 M10 24 61 35 25 48 133 GS CLG 30010
1000 500 M10 30 61 35 25 50 139 GS CLG 50010
1250 630 M10 35 65 35 25 66 145 GS CLG 63010
1500 800 M10 39 73 35 25 90 170 GS CLG 80010
M12 GS CLG 80012
2000 1000 M12 43 81 35 25 100 200 GS CLG 100012
COMPRESSION TYPE FOUR HOLE TIN PLATED COPPER CABLE LUGS (MV)
Features: With Inspection Hole
Application: 0.6KV to 36KV
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
48
TAPER POINT ROD
Air rods are used in conventional lightning protection systems to be the point of interception for lightning
strikes and as such should be considered for inclusion in any air termination design. Air brackets and
couplings at the time of installations.
COPPER AIR RODS
ALUMINIUM AIR RODS
Part Number Thread size
L (mm)
L1 (mm)
Unit Weight (Kg)
GS ATR 16/0.3
M16
300
41
0.53
GS ATR 16/0.5 500 0.85
GS ATR 16/1 1000 1.70
GS ATR 16/1.5 1500 2.59
GS ATR 16/2.0 2000 3.47
GS ATR 20/3
M20
300
41
0.80
GS ATR 20/0.5 500 1.34
GS ATR 20/1 1000 2.68
GS ATR 20/1.5 1500 4.02
GS ATR 20/2 2000 5.36
Part Number Thread size
L (mm)
L1 (mm)
Unit Weight (Kg)
GS ATRA 16/0.3
M16
300
41
0.18
GS ATRA 16/0.5 500 0.29
GS ATRA 16/1 1000 0.57
GS ATRA 16/1.5 1500 0.98
GS ATRA 16/2 2000 1.09
LIGHTNING PROTECTION PRODUCTS
The materials and components contained within this publication reflect our highest demanded products
as opposed to an exhaustive list. Most products can be manufactured out of different materials
(such as stainless steel or galvanised steel) than those presented in this publication. The range
herein contained focuses specifically upon the flat tape approach to lightning protection. Alternative
lightning protection system components include those for cable, wire and solid circular systems. A
complete range of cable, wire and solid circular fixings is available upon request.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
49
FOR USE WITH COPPER AIR
RODS
FOR USE WITH ALUMINIUM AIR
RODS
Material: Gunmetal
Material: Gunmetal
Material: Aluminium
Material: Aluminium
Part Number Air Rod Ø (mm)
H (mm)
W (mm)
Unit Weight (Kg)
GS MP 16 16 & 20 156 72 0.31
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS RS 16 M16 137 34 1.07
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS RSA 16 M16 137 34 0.70
MULTI-POINT
This item can be used in conjunction with the taper pointed copper air rods, but are not essential for installations and are essentially a decorative item.
Material: Gunmetal base with copper spikes.
AIR ROD SADDLES
Air rod saddles are the fixing enabling air rods to be installed on flat roof surfaces and have slots accommodating the installation of air termination network conductors.
FOR USE WITH COPPER AIR RODS
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS ATB 16 M16 101 37 0.50
GS ATB 20 M20
FOR USE WITH ALUMINIUM AIR RODS
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS ATBA 16 M16 101 37 0.15
AIR ROD RIDGE SADDLES
Pitched roofs require an alternative fixing to the standard air rod saddle,
which is why ridge saddles were developed.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
50
Designers frequently wish to affix air rods to the walls of structures to minimise aesthetic impacts, or to prevent impacts upon the horizontal roof surface, or due to other client requirements. The side mounting air rod bracket, accompanied by the rod tape coupling is the fixing to achieve this sort of installation
Material: Gunmetal
Material: Aluminium
METALLIC DC CLIPS
A robust and familiar method of affixing down conductors walls,
metallic DC clips are reliable and simply installed
FOR USE WITH BARE COPPER TAPE
SIDE MOUNTING AIR ROD BRACKETS
Material: Gunmetal
FOR USE WITH COPPER AIR RODS
FOR USE WITH ALUMINIUM AIR RODS
Part Number Rod Ø (mm)
L (mm)
H (mm)
Unit Weight (Kg)
GS ARB 16 16 97 120 0.90 GS ARB 20 20 0.28
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS DC 203 20x3 50 20 10 0.06 GS DC 253 25x3 50 10 0.07 GS DC 254 25x4 50 10 0.07 GS DC 256 25x6 50 12 0.08 GS DC 313 31x3 60 10 0.09 GS DC 316 31x6 60 13 0.09 GS DC 383 38x3 64 10 0.12 GS DC 385 38x5 64 13 0.13 GS DC 386 38x6 64 13 0.14 GS DC 503 50x3 80 10 0.15 GS DC 504 50x4 80 11 0.15 GS DC 506 50x6 80 14 0.16 GS DC 508 50x8 80 14 0.16
Part Number Rod Ø (mm)
L (mm)
H (mm)
Unit Weight (Kg)
GS ARBA 16 16 97 120 0.28
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
51
Material: Aluminium
Material: Phosphor Bronze
Material: Aluminium
Material: Gunmetal
METALLIC DC CLIPS
FOR USE WITH PVC COVERED COPPER TAPE
FOR USE WITH LEAD COVERED COPPER TAPE
FOR USE WITH BARE ALUMINIUM TAPES
FOR USE WITH PVC COVERED ALUMINIUM TAPES
NON-METALLIC DC CLIPS
FOR USE WITH BARE COPPER TAPE
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS DCP 253 25x3 55 20 14 0.10 GS DCP 256 25x6 58 18 0.13 GS DCP 506 50x6 91 19 0.26
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS DCL 253 25x3 77 27 25 0.34
Part Number
Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS DCA 253 25x3 55 20 10 0.03 GS DCA 256 25x6 50 13 0.04 GS DCA 506 50x6 80 16 0.05
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS DCAP 253 25x3 55 20 20 0.04 GS DCAP 506 50x6 80 23 0.05
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Colour Unit Weight
(Kg) GS NDC 203 20x3 55 18 16 Brown 0.01 GS NDC 253 25x3 50 18 16 GS NDC 506 50x6 80 25 26
A lightweight alternative to the metallic DC clips, this polypropylene DC clip
benefits from a hinged lid which facilitates speed of installation, and UV
stabilisation; the combined result is a clip which will not become brittle and
suffers can’t colour degradation. Available in a number of colours to match bare
and PVC covered copper and aluminium tapes.
Material: Polypropylene
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
52
ROD TO TAPE COUPLINGS
This component is designed to incorporate air rods into a down
conductor and must be accompanied by the side mounting air rod
brackets
FOR USE WITH COPPER AIR
RODS
FOR USE WITH ALUMINIUM AIR
RODS
Material: Gunmetal
Material: Aluminium
NON-METALLIC DC CLIPS
FOR USE WITH BARE ALUMINIUM TAPE
FOR USE WITH PVC COPPER & ALUMINIUM TAPE
Part Number
Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Colour Unit Weight (Kg)
GS NDCA 203 20x3 50 18 16 Grey 0.01 GS NDCA 253 25x3
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Colour Unit Weight (Kg)
GS NDCP 253 B 25x3 50 18 16 Brown 0.01 GS NDCP 253 BL Black GS NDCP 253 G Grey
GS NDCP 253 GR Green GS NDCP 253 S Stone GS NDCP 253 W White
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS RTA 16 M16 80 40 0.08
Part Number Thread Size
L (mm)
H (mm)
Unit Weight (Kg)
GS RTC 16 M16 80 40 0.23 GS RTC 20 M20
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
53
An alternative to the DC clip range, these tape clips hold
flat conductors to the surface of a structure.
Material: Copper
Material: Copper
Material: Aluminium
Material: Aluminium
TAPE CLIPS
FOR USE WITH BARE COPPER TAPE
FOR USE WITH PVC COVERED COPPER TAPE
FOR USE WITH BARE ALUMINIUM TAPES
FOR USE WITH PVC COVERED ALUMINIUM TAPE
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS TCC 203 20x3 68 20 7 0.02 GS TCC 253 25x3 70 7 0.02 GS TCC 506 50x6 73 8 0.03
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS TCPC 253 25x3 70 20 7 0.02
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS TCA 203 20x3 68 20 7 0.01 GS TCA 253 25x3 70
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS TCPA 253 25x3 70 20 7 0.01
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
54
Material: Aluminium
ADHESIVE DC CLIPS
Comparable in terms of both design and brief adhesive DC clips are
intended for installation on non-PVC roofs. A non-metallic DC clip is
attached to the adhesive base and the down conductors simply inserted
and secured with the hinged polypropylene lid.
Material: Polycarbonate base with polypropylene clip
Material: Gunmetal
FOR USE WITH ALUMINIUM TAPE
FOR USE WITH BARE COPPER & ALUMINIUM TAPE
FOR USE WITH PVC COVERED TAPE
Part Number Conductor Size (mm)
D (mm)
H (mm)
Colour Unit Weight (Kg)
GS ADC 253 B 25x3 65 23 Brown 0.03 GS ADC 253 G Grey
Part Number Conductor Size (mm)
D (mm)
H (mm)
Colour Unit Weight (Kg)
GS ADCP 253 B 25x3 65 23 Brown 0.03 GS ADCP 253 BL Black GS ADCP 253 GY Grey GS ADCP 253 S Stone GS ADCP 253 W White
Part Number L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS GBHC 3522 35 22 20 0.12
Part Number L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS GBHA 3522 35 22 20 0.04
GLAZING BAR HOLDFASTS
Also within the Gansec Shengyuean holdfast provision, is this holdfast which
should be used when conductor is being affixed to a stable metallic groove.
As the picture indicates, a DC clip (of either sort) can be installed on top of
this.
FOR USE WITH COPPER
TAPE
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
55
Stake holdfasts are a solution to affixing conductors to slate roofs without
the need for drilling. Most commonly supplied with a non-metallic DC clip
to enable a swift installation but it is also possible to supply them with a
metallic Dc clip (as demonstrated in the picture).
Material: Polypropylene clip with aluminium tail
FOR USE WITH BARE COPPER
BACK PLATE HOLDFASTS
The square junction clamp is a versatile, high demand item used in both air
termination networks and down conductor networks but less frequently in earth
termination networks, where it is more advisable to use the Gansec Shengyuean
procedure. With the ability to support straight through applications like a DC
clip, T-junction and full cross connections, the square junction clamp is a popular
item to buy in bulk as it can undertake a number of functions.
FOR USE WITH COPPER TAPE
Material: Gunmetal
STAKE HOLDFASTS
FOR USE WITH PVC COPPER & ALUMINIUM TAPE
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Colour Unit Weight (Kg)
GS SHC 253 B 25x3 300 50 16 Brown 0.02 GS SH 253 G Grey
Part Number
Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Colour Unit Weight (Kg)
GS SHP 253 B 25x3 300 50 16 Brown 0.02
GS SHP 253 BL Black GS SHP 253 G Grey GS SHP 253 S Stone
GS SHP 253 W White
Part Number L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS BPH 3522 35 22 20 0.12
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
56
WATERMAIN PIPE BOND
Utilised extensively in equip potential bonding, the ‘B’
bond is used to secure conductor tapes to metallic
conductive items.
FOR USE WITH COPPER TAPE
Material: Gunmetal with M10x35mm
Stainless steel set screw
Material: Gunmetal
Material: Aluminium
Part Number Conductor Size (mm)
L (mm)
W (mm)
Unit Weight (Kg)
GS WMB 26 26 45 36 0.21
Part Number L (mm)
W (mm)
Unit Weight (Kg)
GS SPC 12240 122 40 0.60
Part Number L (mm)
W (mm)
Unit Weight (Kg)
GS SPA 12240 122 40 0.20
STRIKE PADS
In some applications, it is not possible to install conductors to the
external surface of a structure, particularly where the external surface is
accessible to the public. The strike pad provides an air termination for
concealed conductors beneath the final surface level.
FOR USE WITH COPPER CONDUCTOR
FOR USE WITH ALUMINIUM CONDUCTOR
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
57
RAINWATER PIPE BOND
A further equip potential bonding product which enables the
swift incorporation of tape conductor to a metallic element
FOR USE WITH COPPER TAPE
Material: Gunmetal with M10x40mm
stainless steel set screw
FOR USE WITH ALUMINIUM TAPE
Material: Aluminium with M10x40mm
stainless steel set screw
Part Number Description Unit Weight (Kg)
GS WST 50 50 mm wide x 10 mm length roll
0.20
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS RWB 26 26 32 32 16 0.12
Part Number Conductor Size (mm)
L (mm)
W (mm)
H (mm)
Unit Weight (Kg)
GS RWBA 26 26 32 32 16 0.08
WATERPROOF SEALING TAPE
A waterproof tape for wrapping joints to provide protection
against corrosion. A waterproof tape for wrapping underground
joints.
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
58
PUDDLE FLANGE
Created to prevent water ingress through a roof level, this product
is frequently used to enable electrical continuity to the down
conductor without risking water damage.
Material: Copper
Material: Aluminium
FOR USE WITH COPPER CONDUCTOR
FOR USE WITH ALUMINIUM CONDUCTOR
Part Number L (mm)
W (mm)
Unit Weight (Kg)
GS PFC 61515 600 150x150 1.68
Part Number L (mm)
W (mm)
Unit Weight (Kg)
GS PFA 61515 600 150x150 0.54
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
59
The purpose of a conductor is to provide a planned route for electricity and as such is a fundamental
element of any electrical safety system. There are a number of standards against which conductors are
measured (depending upon their variety) and also specific project requirement based upon their usage on
site. Conductors must be suitable for their ultimate destination (i.e. the environment to which it is
exposed), and usage (able to withstand repeated usage and in line with their interface with other impacts.
The current carrying capacity is an essential performance criterion for any conductor and such an
indicative table for copper tape is provided below (please refer to ___________ for more detail. With
presence on numerous significant projects, Gansec Shengyuean is the obvious choice for all conductor
requirements. This publication does not contain our full scope of conductor provision so should your
requirement not feature, please do not hesitate to contact a member of the Gansec Shengyuean team.
BARE HARD DRAWN COPPER BARS
Standard Coil size 4m. Material: copper to BS EN 12163 (formerly BS 2874)
Part Number Size WxH mm
CSA mm²
Weight per meter (Kg)
GS CT 203 20x3 60 0.53 GS CT 253 25x3 75 0.67 GS CT 254 25x4 100 0.89 GS CT 256 25x6 150 1.33 GS CT 305 30x5 150 1.33 GS CT 386 38x6 228 2.03 GS CT 506 50x6 300 2.68 GS CT 4010 40x10 400 3.56 GS CT 756 75x6 450 4.02 GS CT 5010 50x10 500 4.48 GS CT 1005 100x5 500 4.48 GS CT 6010 60x10 600 5.38 GS CT 1006 100x6 600 5.38 GS CT 10010 100x10 1000 8.89
CONDUCTORS
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
60
Material: Copper to BSEN 13601 (formerly BS 1432)
Utilised on an array of earthing and lightning protection systems on projects
around the globe, the Gansec Shengyuean bare copper tape is manufactured
with a focus on ease of manual handling and installation, however it is
imperative that a site and task specific risk assessment is undertaken before any
installation.
BARE COPPER TAPES
Part Number Size WxH mm
CSA mm²
Standard Coil SIze
Weight per meter (Kg)
GS BCT 12515 12.5x1.5 18.75 100 0.17 GS BCT 1253 12.5x3 37.5 100 0.33 GS BCT 2015 20x15 30 100 0.27 GS BCT 203 20x3 60 100 0.53 GS BCT 2515 25x1.5 37.5 100 0.33 GS BCT 2532 25x3 75 25 0.67 GS BCT 2535 25x3 75 50 0.67 GS BCT 254 25x4 100 50 0.89 GS BCT 256 25x6 150 40 1.33 GS BCT 302 30x2 60 50 0.53 GS BCT 303 30x3 90 50 0.80 GS BCT 304 30x4 120 40 1.07 GS BCT 305 30x5 150 40 1.33 GS BCT 313 31x3 93 50 0.83 GS BCT 3154 31.5x4 126 50 1.13 GS BCT 316 31x6 186 40 1.65 GS BCT 383 38x3 114 50 1.01 GS BCT 385 38x5 190 30 1.69 GS BCT 386 38x6 228 25 2.02 GS BCT 403 40x3 120 40 1.06 GS BCT 404 40x4 160 30 1.42 GS BCT 405 40x5 200 25 1.78 GS BCT 406 40x6 240 25 2.16 GS BCT 4063 40x6.3 252 25 2.24 GS BCT 503 50x3 150 40 1.33 GS BCT 504 50x4 200 30 1.78 GS BCT 505 50x5 250 20 2.22 GS BCT 506 50x6 300 20 2.68 GS BCT 5063 50x6.3 315 20 2.80 GS BCT 508 50x8 400 15 3.60
GANSEC SHENGYUEAN WIRE & CABLE CO.LTD
61
The benefit of a PVC covered conductor is that they can be selected to more closely harmonise with the aesthetics of a structure. Gansec Shengyuean provides the following PVC colours in accordance with BS 5252: Black (18B29), Green (06C39), Grey (00A07), Stone (08B23), White (10B15), and can also provide PVC in Brown (BS 6746C). As with all Gansec Shengyuean products we will always seek to accommodate the need for alternative colours if requested.
Material: Copper to BSEN 13601 (formerly