EAGLE-GRIP™ 3 SERIES ATTACHMENTS OPERATING …

WWW.EASYLIFTEQPT.COM

EAGLE-GRIP™ 3 SERIES ATTACHMENTS OPERATING INSTRUCTIONS

INDEX

OPERATING INSTRUCTIONS ............................................................................ 3

WARRANTY INFORMATION ............................................................................. 4

MAINTENANCE INSTRUCTION ......................................................................... 4

HEAD EXCHANGE PREVENTATIVE MAINTENANCE PROGRAM ............ 5

LOAD CENTER INFORMATION………………………………………………... 6

EG3SCM SCHEMATIC DRAWING .................................................................... 7

PARTS LIST ........................................................................................................... 8

PREVENTATIVE MAINTENANCE AND REBUILD KITS...................…........... 9

OPERATION AND MAINTENANCE CHECKLIST…………………………….. 10

S.O.M. CAM LOCK PARTS ( OPTION )…………………………………………. 11

S.O.M. CAM LOCK PARTS LIST………………………………………………….. 12

1

OPERATING INSTRUCTIONS

MODEL EG3SCM (Single Clamping Mechanism)

TO ATTACH EG3SCM UNIT DIRECTLY TO FORK LIFT CARRIAGE

Remove forks from the forklift carriage. Place top mounting bracket of EG3SCM unit over the top of your

upper fork bar or plate of the carriage, in the location where the bottom mounting bracket of the EG3SCM can

fit into the cut-out portion of the bottom bar or plate. Slide EG3SCM unit slightly left or right of center so both

mounting brackets are seated firmly on the bar. When two units are used, move them to right and left sides of

bar, and drop position lock pin into proper slots or holes. (For handling two 55-gallon standard drums, there

should be 24” between the centerline of both masts.)

WHEN USING SLIDE-ON FORK MOUNTING

Once the forks are in the pockets, the assembly can be secured by attaching the safety chain to the forklift

carriage. When the two EG3SCM units are set on the fork mounting, the position lock pins (located at the top

mounting bracket of the EG3SCM) will slide into the 9/16” holes or slots in the brackets on the fork mounting.

It is IMPERATIVE that these pins be engaged in the holes or slots in order to prevent the units from sliding off

the fork mounting. If drums of other diameters are to be handled, additional 9/16” holes or slots are in the

brackets.

WHEN USING SLIDE-ON FORK MOUNTING WITH THE OPTIONAL QUICK-CLAW SAFETY

RESTRAINT SYSTEM

The patented "Quick Claw" cam locks, when engaged, locks securely to the forks of the forklift to prevent any

chance of sliding off during sudden stops. This also eliminates the need for the operator to dismount the lift

truck to engage or disengage the standard safety chain provided on all Eagle-Grip™ attachments. Unique

rotating cams bind to the heel of each fork when lifted off the ground. When the cam locks come in contact with

the floor, it conveniently releases the attachment. The fork pockets on all Eagle-Grip 3 and 4 series

attachments are 43” in length. This 43” length is designed for use on lift trucks equipped with 42” length forks

for two reasons. The first is insure the tips of the forks do not contact the end of the fork pocket tubes and cause

the tips to penetrate the end of the tubes. The second is that the cam locks need to be in a position where the

heel of the forks is between 1.25” and 1.75” thick. The lift truck forks should be inspected prior to using the

quick-claw attachment to verify the fork thickness where the Quick-Claw cams engage the forks to ensure the

forks are between 1.25” and 1.75” thick. .

In the event the lift truck is equipped with 48” forks it is necessary for the fork pocket of the fork

mounting to be equipped with 49” long fork tubes. If the attachment is not built to accommodate 48”

length forks, the cam-locks on the Quick-Claw option may not function properly. Please consult Easy

Lift Equipment or your local dealer should you require a fork mount frame with longer fork tubes to

accommodate 48” or longer lift truck forks.

TO ADJUST TO PROPER POSITION FOR VARIOUS HEIGHT DRUMS

With unit attached to truck, lower carriage as far as possible. Remove adjustment pin, (item # 23 of drawing)

and lower or raise the clamping mechanism so that the lower jaws are slightly below the bead or rim of the

drum(s). It is advisable to have the cradle touching the lowest possible point of the drum(s) that still permits

engaging the drum(s). EXAMPLE: Top hole is recommended for 55-gallon drums.

TO OPERATE

With mast tilted slightly forward, center attachment with center of drum. Drive truck forward until attachment

contacts drum(s) and presses inner housings back into the outer housings. Raise carriage and drum will be

engaged and ready for transporting. Drum disengagement is accomplished by tilting the mast forward, then

lowering the carriage until the jaws have retracted completely. Truck operator can now back away to engage

another drum.

NOTE: All Eagle-Grip Attachments conform to OSHA standards. A metal plate, affixed to each

attachment, provides model number, serial number, rated capacity and attachment weight. OSHA

requires contacting the lift truck manufacturer for written approval of any attachment to be used on a

lift truck. Should the metal plate be missing - call for a free replacement

MAINTENANCE INSTRUCTIONS

Proper care and preventive maintenance of your new drum handling attachment will ensure productive, safe

handling and will provide you with many years of efficient, worry free service.

1. Perform a visual inspection of the attachment each time before using it. Check to see that all pins, cotter

pins, housings, and springs are in place. Missing parts can cause diminished performance or equipment

malfunction. Be sure to check the belts on the cradle for wear and tension. Worn or broken belts provide

little or no support. Belt tension should be adjusted to less than complete taught so they can provide a small

amount of spring and absorb shocks while transporting over rough ground.

2. Preventive maintenance should be performed either in conjunction with existing timetables or every 3-4

weeks. The clamping mechanism(s) (Part # 6004) should be sprayed thoroughly with a light grade oil (WD-

40 or equivalent substitute). This procedure will free any foreign matter that has gotten caught in the

clamping mechanism(s) and lubricate all moving parts. Once oiled, all parts should move freely with hand

manipulation. The top and bottom bar of the slide-on mounting should be lubricated with light crease. This

procedure allows the EG3SCM-CM’s to be moved easily from side to side on the slide-on mount if not used

on the actual fork lift carriage.

Heavy use of the attachment (6 or more hours daily) may require that certain parts be replaced on a yearly basis.

Preventive Maintenance Kits are available. Call your Eagle-Grip Attachment distributor for more

information.

HEAD EXCHANGE PREVENTIVE MAINTENANCE PROGRAM

Designed to provide our customers with a scheduled maintenance program to insure ultimate performance and long life.

Aside from required visual inspections, belt replacement and monthly lubrication, the clamping assembly(s) or heads should have a scheduled preventive maintenance service. The intervals between services dependent on usage, but should be done at least annually.

HOW IT WORKS AND WHAT IT COSTS:

• Customers will be notified of their next scheduled p.m. service. • Upon approval, a loaner head(s) will be shipped for the customer for use while

customers’ head(s) are being serviced. (Heads are generally shipped by UPS) • Customers then return the head(s) to be serviced in the same carton that has a

return authorization number affixed to it. (See instructions below for clamping head removal from the mast.)

• Upon receipt, the customer will be notified of the exact cost of the service for prior approval. Costs are determined by the required parts, labor, and all freight/UPS charges. The use of loaner heads is free of charge.

• Upon completion, the serviced heads are returned to the customer, and the swap procedure is reversed with the loaner heads being returned to the factory.

SCOPE OF WORK TO BE PERFORMED:

• Inspection and disassembly of clamping mechanism. • Clean or sandblast and repaint all parts as required. • Replace springs, cotter pins, or any worn parts as necessary. • Reassemble clamping mechanism and lubricate.

If requested the entire attachment can be shipped to the factory to have the p.m. service performed or for complete refurbishment. Attachment loaners are also available at no charge. Due to the heavier weight of the attachments shipping is done via common carrier, and is more costly than UPS. Should you have any questions regarding this procedure, please call customer service at 800-233-1800/302-737-7000 or your Eagle-Grip™ Attachment distributor for clarification.

TO REMOVE CLAMPING ASSEMBLY FROM MAST:

All Eagle-Grip™ clamping assemblies (heads) are designed for easy removal from the masts, without tools, in seconds. To remove the head assembly, pull the hairpin clip (item #17) from the adjustment pin (item #14). Lift slightly on the head assembly and remove the adjustment pin (item #14). Slide the complete assembly out of the mast and reverse the process with the replacement head. .

5

6.

Capacity Weight H x L x W Drums

Model (lbs/kg) (lbs/Kg) (inches) (mm) Handled Description

EG3SCM-CM

EG3SCMSRC-CM

1500/680

1500/680

85/39

85/39

33x15x18

33x15x18

838x381x457

838x381x457

1

1

Carriage Mount

Carriage Mount

EG3SCM-NF

EG3SCMSRC-NF

EG3SCM-NFQC

EG3SCMSRC-NFQC

1500/680

1500/680

1500/680

1500/680

228/104

228/104

316/143

316/143

37x47x24

37x47x24

42x47x24

42x47x24

940x1194x610

940x1194x610

1067x1194x610

1067x1194x610

1

1

1

1

Narrow Fork Mount

Narrow Fork Mount

Narrow Fork Mount/Quick Claw

Narrow Fork Mount/Quick Claw

EG3SCM-F

EG3SCMSRC-F

EG3SCM-FQC

EG3SCMSRC-FQC

1500/680

1500/680

1500/680

1500/680

306/139

306/139

394/179

394/179

37x47x33

37x47x33

42x47x33

42x47x33

940x1194x838

940x1194x838

1067x1194x838

1067x1194x838

1

1

1

1

Adjustable Fork Mount


Adjustable Fork Mount/Quick Claw


EG3SCM2-F

EG3SCMSRC2-F

EG3SCM2-FQC

EG3SCMSRC2-FQC

3000/1361

3000/1361

3000/1361

3000/1361

382/173

382/173

470/213

470/213

37x47x33

37x47x33

42x47x41

42x47x41

940x1194x838

940x1194x838

1067x1194x1042

1067x1194x1042

1 or 2

1 or 2

1 or 2

1 or 2





PART# 4902

EGNF

EGNFQC

EGF

EGFQC

1500/680

1500/680

1500/680

3000/1361

3000/1361

69/31

212/96

300/136

221/100

309/140

33x15x18

37x47x24

42x47x24

20x43x33

25x43x33

838x381x457

940x1194x610

1067x1194x610

508x1092x838

635x1092x838

Replacement Carriage Mount

Without Clamping Mechanism

Replacement Narrow Fork Mount

Replacement Narrow Fork Mount

With Quick-Claw

Replacement Fork Mount Frame

Replacement Fork Mount Frame

with Quick-Claw

* All Carriage Mount models are made to fit a Class II carriage unless otherwise specified

LOST LOAD CENTER: The distance from the tip of the forks to the center of the drum (excludes CM models)

MODEL NUMBER

EG3SCM-CM & EG3SCMSRC-CM 23” from carriage to center of drum

12” from carriage to beginning of drum

EG3SCM-NF & EG3SCMSRC-NF 12” from end of pockets to center of drum

EG3SCM-NFQC & EG3SCMSRC-NFQC 12” from end of pockets to center of drum

EG3SCM-F & EG3SCMSRC-F 13” from end of pockets to center of drum

EG3SCM-FQC & EG3SCMSRC-FQC 13” from end of pockets to center of drum

EG3SCM2-F & EG3SCMSRC2-F 13” from end of pockets to center of drum

EG3SCM2-FQC & EG3SCMSRC2-FQC 13” from end of pockets to center of drum

VERTICAL CENTER OF GRAVITY:

The distance measured from the bottom of the attachment to the center point of the

carriage mount at which it balances.

MODEL NUMBER

EG3SCM-CM & EG3SCMSRC-CM 15”

EG3SCM-NF & EG3SCMSRC-NF 10” (w/43” Fork Pockets)

EG3SCM-NFQC & EG3SCMSRC-NFQC 13” (w/43” Fork Pockets)

EG3SCM-F & EG3SCMSRC-F 10” (w/43” Fork Pockets)

EG3SCM-FQC & EG3SCMSRC-FQC 13” (w/43” Fork Pockets)

EG3SCM2-F & EG3SCMSRC2-F 12” (w/43” Fork Pockets)

EG3SCM2-FQC & EG3SCMSRC2-FQC 15” (w/43” Fork Pockets)

7.

HORIZONTAL CENTER OF GRAVITY: The distance or point that is measured between the beginning of the fork pockets

to a middle point of the attachment which the attachment balances.

MODEL NUMBER

EG3SCM-CM & EG3SCMSRC-CM 6.25” from face of carriage

EG3SCM-NF & EG3SCMSRC-NF 30” (w/43” Fork Pockets)

EG3SCM-NFQC & EG3SCMSRC-NFQC 28” (w/43” Fork Pockets)

EG3SCM-F & EG3SCMSRC-F 30” (w/43” Fork Pockets)

EG3SCM-FQC & EG3SCMSRC-FQC 28” (w/43” Fork Pockets)

EG3SCM2-F & EG3SCMSRC2-F 31.5” (w/43” Fork Pockets)

EG3SCM2-FQC & EG3SCMSRC2-FQC 29.5” (w/43” Fork Pockets)

43.0" 13.00"

42" Forks

22.50"

FOR PARTS, SERVICE OR TECHNICAL QUESTIONS CALL:

Easy Lift Equipment

2 Mill Park Ct.

Newark, DE. 19713

800-233-1800 ; 302-737-7000

FAX: 302-737-7333

www.easylifteqpt.com

Email: [email protected]

http://www.easylifteqpt.com/

WARRANTY POLICY Easy Lift Equipment warrants it’s products to the original purchaser to be free from factory material and

workmanship defects. All warranties begin on the date of delivery to a customer’s location for a period of 1 year.

Defective parts or components may be required to be returned freight prepaid should a return authorization be

issued. Easy Lift Equipment shall be the sole judge of the validity of any claim or defect and may elect to make

any replacement or repair of any part thereof that it has agreed is defective. Wearable Items: Such as hoses,

bearings, brushes, seals and wheels shall be warranted for a period of 90 days. Labor coverage is limited to 90

days at the rate of $ 50.00 per hour. Travel time and mileage are not covered under this warranty.

Easy Lift Equipment Co., Inc. assumes no liability whatsoever to work done, parts replaced, or expenses incurred

not specifically authorized by it. Normal maintenance or replacement of service items is not covered by this

warranty. No warranty claims will be considered to customers with any delinquent outstanding balance.

The warranty described here above shall constitute the sole remedy of the dealer and/or the initial purchaser. Easy

Lift Equipment Co., Inc., shall under no circumstances be liable for special, general incidental or consequential

damages.

To make a claim under this guarantee, send a completed warranty claim to Easy Lift Equipment for consideration.

Do not return defective parts unless a return authorization (RA) has been sent requesting for return.

WARRANTY LIMITATION:

Easy Lift Equipment Co., Inc. reserves the right to void warranty coverage if the unit has been overloaded beyond

capacity limitation, damaged due to abuse, neglect, freight damage or that have been modified or repaired in any

manner not approved by Easy Lift Equipment. Units used in abrasive or corrosive conditions, in freezers or

excessive moisture, must be properly equipped for the environment to assure the warranty is not voided.

When batteries, battery chargers or scale indicators are purchased from Easy Lift Equipment, the original

manufacturer’s warranty applies. Warranty service and claims should be directed to the local representative of the

original manufacturer in your area or we will assist the customer in locating a local service representative in their

area.

SUBMITTING CLAIMS:

If failure occurs an Easy Lift Equipment claim form must be submitted to Easy Lift Equipment Co., Inc. within

(30) thirty days of the completion of repair. Claim forms are available by calling 800-233-1800, faxing to 302-

737-7333 or by writing to [email protected]. A copy of the work order made at the time of the repair and

parts claimed under warranty may be requested for Easy Lift Equipment’s inspection. Do not send defective parts

to Easy Lift unless requested.

ORDERING PARTS:

Easy Lift Equipment Co., Inc. products are distributed through a sales and service organization that is eager and

capable to service the equipment it has sold. You will be well taken care of whenever parts, adjustments or repairs

are needed. When contacting Easy Lift Equipment, please be sure to state Model No. and Serial No. for the

equipment and use part numbers and nomenclature as shown in parts listing. Adherence to above procedure

will save time and provide speedy assistance when it counts. You are of course always welcome to bring to us any

questions, comments or recommendations pertaining to your Easy Lift Equipment Co., Inc. products.

MANUFACTURER CONTACT INFORMATION:

Easy Lift Equipment Co., Inc. Phone: 800-233-1800: 302-737-7000

2 Mill Park Ct. Fax: 302-737-7333

Newark, DE 19713 Website: www.easylifteqpt.com

Email: [email protected]

www.easylifteqpt.com 800-233-1800 Updated: 10/17/2014

mailto:[email protected]

212223

24

2526

2728

28d

28c13

28a

3456

121110987

16

15

18

19

20

13

1

14

2

26

EG3SCM - CM

17

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 1202 200.00$ Outer Housing (Black Powder Coating) 11 1202SS 300.00$ Outer Housing (Stainless Steel-Non-Sparking) 12 7902 150.00$ Inner Housing (Black Powder Coating) 12 7902SS 200.00$ Inner Housing (Stainless Steel - Non-Sparking) 13 1007 80.00$ Upper Clamp Jaw (Black Powder Coating) 13 1007M 80.00$ Mauser Upper Clamp Jaw (Black Powder Coating) 13 1007SRJ 100.00$ Clamp, Jaw-Upper (Non-Sparking) 14 5107 80.00$ Lower Clamp Jaw (Black Powder Coating) 14 5107M 80.00$ Mauser Lower Clamp Jaw (Black Powder Coating) 14 5107SRJ 100.00$ Clamp, Jaw- Lower (Non-Sparking) 15 9996 3.00$ Hook, Housing Spring (Stainless Steel) 16 2206 13.50$ Housing to Housing Spring (zinc) 17 72041 6.75$ Pin, Link to Upper Jaw (zinc) 18 10061 6.75$ Pin, Upper Jaw to Housing (zinc) 19 70091 20.25$ Link, Jaw to Jaw 2

10 4306 12.50$ Jaw Spring (zinc) 111 62041 6.75$ Pin, Link to Lower Jaw (zinc) 112 18006-1 16.75$ Pin, Housing to Housing (zinc) 113 6006-CP 0.35$ Cotter Pin, 5/32" x 1" (zinc) 614 19106-1 20.00$ Adjustment Pin (zinc) 115 1700-7 45.00$ Adjustment Slide (Black Powder Coating) 216 8996 15.75$ Clevis Spring Hook (Stainless Steel) 217 7016 4.00$ Circle Cotter "Hang 2" 118 3202 100.00$ Clevis 2

18a 3202P 22.50$ Clevis Replacement Pin 219 17006-1 20.00$ Pin, Clevis to Housing 220 3206 17.00$ Spring, Clevis 221 36006-1 16.75$ Pin, Lock to Carriage 122 1506 0.40$ Roll Pin for Carriage Lock # 360061 (zinc) 123 4902 600.00$ Belt Cradle Frame (Belt Incl.) 124 3516 60.00$ Rubber Belt 124 3516SC 70.00$ Anti-Static Rubber Belt 124 8516 80.00$ PVC Belt 125 12200-4 17.50$ Belt Clamp (Yellow Powder Coating) 226 2906 0.50$ 5/16" - 18 Hex Nut (zinc) 826 4017 0.50$ 5/16" x 1-1/4" Hex Head Bolt (zinc) 827 6902 45.00$ Adjusting Rod for Belt Clamp 127 3906 1.00$ 5/8" - 11 Hex Nut (zinc) 227 7707 0.50$ 5/8" Lock Washer (zinc) 128 504 88.00$ Safety Chain & Cam Lock Assembly 1

28a 0504A 25.00$ Clamp, Cam Lock (zinc) 128b 6006-CP 0.35$ Cotter Pin, 5/32" x 1" (zinc) 228c 4006-1 16.50$ Pin, Cam Lock 128d 0504D 44.00$ Cam, Cam Lock 1

QL312-DP 1.50$ Quick Link 1WLG 7.00$ 12oz White Lithium Grease 1

Assembled Price #1 thru #206304 700.00$ EG3 Single Clamping Mechanism (Black Powder Coating)6304M 700.00$ EG3 Mauser Single Clamping Mechanism (Black Powder Coating)6304SRC 850.00$ EG3 Single Clamping Mechanism (Stainless Steel - Non-Sparking)

EAGLE-GRIP™ SERIES 3 HEAVY DUTY CLAMPING MECHANISMPARTS LIST

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 1/5/2016

ITEM PART NO. PRICE EACH DESCRIPTION QTY6 2206 13.50$ Housing to Housing Spring (zinc) 1

10 4306 12.50$ Jaw Spring (zinc) 113 6006-CP 0.35$ Cotter Pin, 5/32" x 1" (zinc) 617 7016 4.00$ Circle Cotter "Hang 2" 120 3206 17.00$ Spring, Clevis 224 3516 60.00$ Rubber Belt 1

WLG 7.00$ 12oz White Lithium Grease 1

ITEM PART NO. PRICE EACH DESCRIPTION QTY2 7902 150.00$ Inner Housing (Black Powder Coating) 13 1007 80.00$ Upper Clamp Jaw (Black Powder Coating) 14 5107 80.00$ Lower Clamp Jaw (Black Powder Coating) 15 9996 3.00$ Hook, Housing Spring (Stainless Steel) 16 2206 13.50$ Housing to Housing Spring (zinc) 17 72041 6.75$ Pin, Link to Upper Jaw (zinc) 18 10061 6.75$ Pin, Upper Jaw to Housing (zinc) 19 70091 20.25$ Link, Jaw to Jaw 2

10 4306 12.50$ Jaw Spring (zinc) 111 62041 6.75$ Pin, Link to Lower Jaw (zinc) 112 18006-1 16.75$ Pin, Housing to Housing (zinc) 113 6006-CP 0.35$ Cotter Pin, 5/32" x 1" (zinc) 616 8996 15.75$ Clevis Spring Hook (Stainless Steel) 217 7016 4.00$ Circle Cotter "Hang 2" 118 3202 100.00$ Clevis 219 17006-1 20.00$ Pin, Clevis to Housing 220 3206 17.00$ Spring, Clevis 224 3516 60.00$ Rubber Belt 1

WLG 7.00$ 12oz White Lithium Grease 1

PARTS LIST

ALL ABOVE ITEMS: PART NUMBER EG3RBKIT(PRICE IF ALL ITEMS PUCHASED SEPARATELY)

105.28$ 133.10$

645.60$ 795.10$

EAGLE-GRIP™ SERIES 3 PREVENTATIVE MAINTENANCE KITPARTS LIST

ALL ABOVE ITEMS: PART NUMBER EG3PMKIT(PRICE IF ALL ITEMS PUCHASED SEPARATELY)

EAGLE-GRIP™ SERIES 3 COMPLETE REBUILD KIT


EG3 & EG4 SLIDE ON MOUNT ASSEMBLIES

1

2

3

4

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 EGF 950.00$ Fork Mount Frame for EG3 & EG4 12 4902 600.00$ Belt Cradle Frame (Belt Incl.) 1 or 23 EGNF 1,175.00$ Narrow Fork Mount Frame for EG3 & EG4 14 504 88.00$ Safety Chain & Cam Lock Assembly 1

EAGLE-GRIP™ EG3 & EG4 SLIDE ON MOUNT ASSEMBLIESPARTS LIST


1

2

3

45

6

7

8

S .O. M

. P OC

KET C

AM

LOC

K PA

RTS

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 QCH2.5 100.00$ Cam Housing 22 QCC2.5 100.00$ Single Cams 23 343SHB 7.50$ 3/4" x 3" Socket Shoulder Bolts 24 34FW 0.25$ 3/4" Fender Washer 25 58FW 0.25$ 5/8" Fender Washer 26 48SLN 0.75$ 5/8" Stover Lock Nuts 27 KH100799 15.00$ Spring (zinc) 48 QCFPS 40.00$ Front Fork Pocket Support 2

ALL ABOVE ITEMS: QCKIT-EG3/4 510.00$ All parts required for customer installed QUICK-CLAW option for EG3 & EG4 modelsNOTE: Installation of these parts require 43" fork pocket length alongwith welding of front fork pocket supports and cam housings.

QUICK-CLAW SAFETY RESTRAINT SYSTEMPARTS LIST


W G BKR

#1-W

#3 GN

#4 BK

#2 R

#1-W

#2R

#4 BK

#3 GN

CAL UNITS

S3 S4

JU7

JU8

SIGSIGEXCEXCSENSEN

TB1

WHITERED

GREENBLACK

# 2

# 2

#3 #4 #5 #6

#7

#10 #12

#11 #13

#8

#9

#14

#1

SEE PARTS LISTSCALE WIRING DIAGRAM

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 8000XLM 850.00$ Doran™ 8000XL Non-intrinsically Safe Scale Indicator (Internal Battery & Charger)1

1A SUB0038-4 85.00$ Replacement Battery for 8000XLM Indicator 11 2200 750.00$ Doran™ 2200 Non-intrinsically Safe Scale Indicator (Numeric Keypad) 1

1A EXOPT187 175.00$ Battery Option for Non-Intrinsically Safe 2200 Indicator 11 8000IS 1,840.00$ Doran™ 8000IS Intrinsically Safe Scale Indicator FM Approved (Includes Battery & Charger)1

1A 8000BIS 595.00$ Battery for Doran™ 8000IS FM Approved Indicator 11B 8000CIS 255.00$ Charger for Doran™ 8000IS Indicator 11 9000IS 2,095.00$ Doran™ 9000IS Intrinsically Safe Scale Indicator FM Approved (Includes Battery & Charger)1

1A 9000BIS 595.00$ Battery for 9000IS Indicator 11B 9000CIS 245.00$ Charger for 9000IS Indicator 11C SUB0038-4 85.00$ Replacement Battery for 8000XLM Indicator 12 HM1000 383.00$ Load Cell with 4' cable 23 CU-124 14.58$ Terminal Box Enclosure 14 7531A34 1.00$ Two Sided Tape (6" Length) 15 7527K64 5.75$ Terminal Box 16 3A214 0.75$ Terminal Eyelet 127 4/24AWG(SM)-7 22.00$ Load Cell Cable 7' 18 AP2074891 11.25$ Strain Relief 29 AP2074901 12.00$ Plug 2

10 AP2061531 12.75$ Connector (Male) 111 AP2060601 14.50$ Connector (Female) 112 AP661034 3.00$ Terminal Pin 413 AP661054 3.50$ Terminal Socket 414 ZZHEY3208 8.38$ Cable Fitting 415 IMB8000 150.00$ Indicator mount Bracket with Pin 1

ENC0624 40.00$ Stainless Steel Bracket (8000XLM) 1ENC0231 75.00$ Stainless Steel Bracket (8000IS) 1

ELSCAC 158.50$ Scale Cable Assem (inc. items (#6 thru #13) 1-24" & 1-60" Length

ELSCAME 72.85$ Scale Cable Assem. Male End (Inc. items #7,8,9,10&12) 24" Length

ELSCAMF 85.65$ Scale Cable Assem. Female End (Inc. items#6,7,8,9,11&13) 60" Length

SCALE WIRING PARTS LIST


Eagle-Grip™ Attachment Operator Daily Inspection Checklist

Has the attachment been properly secured to the lift truck by means of a safety chain or “Quick-Claw” cam locking devise to prevent a slippage accident? YES NO Is any hardware loose or missing from the attachment, such as: head adjustment pins & clips, pins & cotter pins, springs, trunion bolts? YES NO Are the belts torn, missing, or not adjusted properly on the attachment? YES NO Does the attachment appear to have any cracked welds or appear to be unsafe to use? YES NO Has the operator read the operation manual and been trained in the use of the attachment? YES NO

COMMENTS: _________________________________________________________________________________

Eagle-Grip™ Attachment Maintenance Monthly Checklist

NEEDS REPAIRS Structural Steel: OK REPAIR COMPLETED 1. Look for cracked welds on frame work. 2. Flip the attachment forward to inspect the ends of both

fork pockets for weld cracks. 3. Lubricate the top and bottom rails of the fork mount frame

to permit the masts to slide left and right. 4. Check masts to see if the 16” distance between the upper and lower supports that slide on the fork mount frame have become separated to the point of becoming unattached when lifting a drum. 5. Check the safety chain and cam lock for wear and missing parts. Clamping Heads: 1. Inspect heads for loose or missing pins, cotter pins, trunion bolts,

springs, pins, snap rings and replace as necessary. 2. Lubricate clamping mechanisms. Belts: Check belts for wear and adjust for proper tension Annually: 1. Replace all springs. 2. Check to verify that specification data plates are affixed to the attachment. Every Three Years: Replace all pins, inner housings and links Date of Inspection: Serial Number: Name of Inspector:

10

Documents

EAGLE-GRIP™ 3 SERIES ATTACHMENTS OPERATING …