E0 · 2014. 10. 17. · 15a 120v 1ph isolated ground duplex receptacle, hubbell no.ig-5252 provide separate neutral and ground wire for each outlet. 15a 120v 1ph gfci grounded duplex

1. DEFINITIONS:

PROVIDE - MEANS 'SUPPLY AND INSTALL'. INSTALL - MEANS 'MOUNT AND WIRE'. WIRE - MEANS

'SUPPLY AND INSTALL ALL REQUIRED WIRE AND RACEWAYS AND MAKE ALL CONNECTIONS.

CONCEALED - MEANS 'NOT VISIBLE ON COMPLETION'. EXPOSED - MEANS 'VISIBLE ON

COMPLETION'.

2. FOR GENERAL CONDITIONS REFER TO CONTRACT DOCUMENTS.

3. INCLUDE ALL NECESSARY MATERIALS, LABOUR AND EQUIPMENT TO INSTALL ELECTRICAL WORK

AS INDICATED AND SPECIFIED HEREIN.

4. USE ONLY NEW AND CSA CERTIFIED EQUIPMENT AND MATERIALS. ONLY FIRST CLASS

WORKMANSHIP WILL BE ACCEPTED IN REGARD TO ACCEPTED STANDARD PRACTICES, SAFETY,

ACCESSIBILITY, DURABILITY AND NEATNESS OF DETAIL.

5. BASE TENDER PRICE ON MATERIALS AND EQUIPMENT SPECIFIED OR LISTED FIRST. IF

ALTERNATE EQUIPMENT IS PROPOSED INDICATE COST SAVING. DESIGN IS BASED ON

DIMENSIONS AND PHYSICAL CONFIGURATIONS OF MANUFACTURER'S EQUIPMENT SPECIFIED OR

LISTED FIRST. PAY FOR WORK REQUIRED BY OTHER DIVISIONS TO ACCOMMODATE ALTERNATE

EQUIPMENT.

6. DO COMPLETE INSTALLATION IN ACCORDANCE WITH LATEST EDITION OF THE ONTARIO

ELECTRICAL SAFETY CODE,ONTARIO BUILDING CODE AND THE REQUIREMENTS OF LOCAL

INSPECTION AUTHORITIES HAVING JURISDICTION. ADHERE TO RULES AND REGULATIONS OF

BASE BUILDING. COORDINATE ALL WORK WITH BASE BUILDING PERSONEL AS NECESSARY TO

PERFORM WORK IN AS EXPEDITIOUS AS MANNER AS POSSIBLE.

7. EXAMINE THE SITE AND LOCAL CONDITIONS AFFECTING THE WORK. NO EXTRAS TO TENDER

PRICE WILL BE APPROVED FOR ANY EXPENSES INCURRED THROUGH FAILURE TO EXAMINE THE

SITE.

8. SUBMIT TO ELECTRICAL INSPECTION DEPARTMENT NECESSARY NUMBER OF DRAWINGS AND

SPECIFICATION FOR EXAMINATION AND APPROVAL PRIOR TO COMMENCEMENT OF WORK. PAY

ASSOCIATED FEES.

9. DRAWINGS AND SPECIFICATIONS INDICATE INTENT OF DESIGN ONLY. DRAWINGS ARE TO BE

CONSIDERED AS DIAGRAMMATIC ONLY AND DO NOT SHOW ALL STRUCTURAL AND

CONSTRUCTION DETAILS. OBTAIN ANY INFORMATION INVOLVING ACCURATE MEASUREMENTS

OF BUILDING FROM ARCHITECTURAL AND STRUCTURAL DRAWINGS OR AT SITE. MAKE ANY

NECESSARY CHANGES OR ADDITIONS TO ACCOMMODATE STRUCTURAL CONDITIONS WITHOUT

ADDITIONAL CHARGE.

10. FURNISH A CERTIFICATE OF ACCEPTANCE FROM INSPECTION DEPARTMENT ON COMPLETION OF

WORK.

11. CLEAN AND TOUCH-UP SURFACES OF SHOP PAINTED EQUIPMENT, SCRATCHED OR MARRED

DURING SHIPMENT OF INSTALLATION TO MATCH ORIGINAL PAINT.

12. CHANGE LOCATION OF LUMINAIRES AND DEVICES AT NO EXTRA COST OR CREDIT, PROVIDING

DISTANCE DOES NOT EXCEED 10'-0" AND INFORMATION IS GIVEN PRIOR TO INSTALLATION.

13. MEASURE PHASE CURRENTS OF PANELBOARDS WITH NORMAL LOADS (LIGHTING) OPERATING.

ADJUST BRANCH CIRCUIT CONNECTIONS AS REQUIRED TO OBTAIN BALANCE OF CURRENT

BETWEEN PHASES NOT EXCEEDING 10% MAXIMUM AND RECORD CHANGES.

14. UPON COMPLETION OF WORK DO FINAL CLEANING. CLEAN LIGHTING REFLECTORS, LENSES AND

OTHER LIGHTING SURFACES THAT HAVE BEEN EXPOSED TO CONSTRUCTION DUST AND DIRT.

15. MAINTAIN RECORD OF ALL REVISIONS. PREPARE RECORD DRAWINGS IN NEAT MANNER

SHOWING ALL DEVIATIONS IN WORK. ON COMPLETION OF WORK SUBMIT TO THE CONSULTANT

IN AUTOCAD FORMAT AND ONE REPRODUCIBLE SET RECORD DRAWINGS.

16. SAW CUTTING, DRILLING AND PATCHING FOR FLOOR OUTLETS AND CONDUITS BY GENERAL

CONTRACTOR. OBTAIN LANDLORD'S APPROVAL PRIOR TO PROCEEDING WITH WORK.

17. 120/208V & 346/600V PANELBOARDS SHALL HAVE BOLT-ON BREAKERS RATED 10KA & 18KA IC

RESPECTIVELY. TWO AND THREE POLE BREAKERS SHALL HAVE COMMON TRIP. 'DUPLEX'

BREAKERS AND TIE HANDLES WILL NOT BE ACCEPTED. PANELBOARDS TO BE PRODUCT OF ONE

MANUFACTURER. ACCEPTABLE MANUFACTURERS: SQUARE-D, F.P.L., SIEMENS, CUTLER

HAMMER. MOUNT ALL SURFACE MOUNTED PANELS ON PLYWOOD BACKBOARDS.

18. DISCONNECT SWITCHES: HEAVY DUTY SAFETY SWITCHES 600V, TYPE 'A', HORSEPOWER RATED,

QUICK-MAKE, QUICK-BREAK MECHANISM, WITH PROVISION FOR PAD LOCKING IN THE 'ON' AND

'OFF' POSITION. DISCONNECT SWITCHES TO BE PRODUCT OF ONE MANUFACTURER.

ACCEPTABLE MANUFACTURERS: F.P.L., SQUARE-D, SIEMENS, CUTLER HAMMER.

19. FUSES: TO CSA C22.2 No. 106-M1985, HRCI-J. GOULD TYPE AJT AND HRC-L ABOVE 600A, GOULD

TYPE A4BT IN SWITCHBOARDS. HRCI-R (ULC RK5) TIME DELAY TYPE IN OTHER DISTRIBUTION

EQUIPMENT.

20. DISTRIBUTION TRANSFORMERS: DRY TYPE, CLASS H INSULATION, TEMPERATURE RISE 150°C

FOR COILS, TO CSA C22.2 NO. 47 AND CSA C9 STANDARDS, WITH MAXIMUM LOSSES TO CSA

802.94, WITH SPRINKLER-PROOF ENCLOSURES. TRANSFORMERS TO BE PRODUCT OF ONE

MANUFACTURER. ACCEPTABLE MANUFACTURERS: HAMMOND, POLYGON, DELTA, ACME

TRANSFORMER, F.P.L., MARCUS. USE RUBBER PADS FOR ISOLATION OF TRANSFORMERS FROM

BUILDING CONSTRUCTION.

21. PROVIDE COMPLETE PERMANENT AND CONTINUOUS SYSTEM, CIRCUIT AND EQUIPMENT

GROUNDING.

22. IDENTIFY ALL ELECTRICAL EQUIPMENT WITH LAMICOID BLACK PLATES WITH 1/4" HIGH ETCHED

WHITE LETTERS. SECURE PLATES TO THE EQUIPMENT USING CONTACT CEMENT.

IDENTIFICATION PLATES SHALL INDICATE NAME OF EQUIPMENT OR EQUIPMENT CONTROLLED.

PROVIDE TYPEWRITTEN SCHEDULES ON BACK OF EACH PANEL DOOR UNDER A TRANSPARENT

COVER. SCHEDULE TO SHOW AREA OR EQUIPMENT CONTROLLED BY EACH CIRCUIT.

23. MAINTAIN COLOUR CODE OF ALL CONDUCTORS. COLOUR CODE TO CSA C22.1-1994. ALL WIRING

SHALL BE COPPER MINIMUM #12 T90 TWH OR R90 (X-LINK) INSTALLED IN CONDUIT. WHERE

CONDUCTOR SIZE IS NOT INDICATED, SIZE IT FOR CURRENT CARRYING CAPACITY OF

PROTECTING DEVICE AND VOLTAGE DROP AT OUTLET OF 5% MAXIMUM. ARMOURED FLEXIBLE

CABLE MAY BE USED FOR SHORT BRANCH CIRCUIT CONNECTIONS BETWEEN OUTLETS AND

MOTORIZED EQ., FIXED APPLIANCES, IN CEILING SPACES FOR FINAL CONNECTION TO LIGHTING

LUMINAIRES (10'-0" MAX.), FOR WIRING DEVICES IN DRYWALL AND DOUBLE MASONRY

PARTITIONS AND FURRED SPACES. TIE ARMOURED CABLES TO BUILDING CONSTRUCTION

WHERE USED FOR EXPOSED WRING, AVOID LOOSE CABLES.

24. PROVIDE SUITABLE METAL BRACKETS, FRAMES HANGERS, CLAMPS AND RELATED TYPES OF

SUPPORT TO SUPPORT CONDUIT AND CABLE RUNS. FASTEN EXPOSED CONDUITS TO BUILDING

CONSTRUCTION OR SUPPORT SYSTEM USING ONE HOLE MALLEABLE IRON STRAPS. SUPPORT

TWO OR MORE CONDUITS ON U-CHANNELS SUPPORTED BY MINIMUM 1/4" DIAMETER THREADED

ROD HANGERS WHERE DIRECT FASTENING TO BUILDING CONSTRUCTION IS IMPRACTICAL. TO

SUPPORT CONDUITS FROM U-CHANNEL USE ONE PIECE PIPE CLAMPS.

25. RUN ALL CONDUITS CONCEALED IN FINISHED AREAS. CONDUITS IN SERVICE AREAS MAY BE

SURFACE. USE EMT CONDUIT WITH DIE CAST SET SCREW-TYPE CONCRETE TIGHT COUPLINGS

AND CONNECTORS IN DRY AREAS. USE FLEXIBLE METAL CONDUIT FOR CONNECTION TO

MOTORS IN DRY AREAS AND DRY TYPE TRANSFORMERS. USE LIQUID-TIGHT FLEXIBLE METAL

CONDUIT WITH COMPRESSION RAIN TIGHT COUPLINGS AND CONNECTORS WITH INSULATED

THROAT FOR CONNECTION TO EQUIPMENT IN DAMP OR WET LOCATIONS. WHERE CONDUIT SIZE

IS NOT INDICATED, SIZE CONDUIT TO ALLOW 25% SPARE CAPACITY. INSTALL FISH CORD IN ALL

EMPTY CONDUITS. WHERE CONDUITS PASS THROUGH FLOORS AND FIRE RATED WALL, SEAL

SPACE BETWEEN CONDUIT AND STRUCTURE WITH CANSTRUT ELASTA-SEAL (OR APPROVED

EQUAL).

26. PROVIDE JUNCTION AND OUTLET BOXES WHERE NECESSARY FOR PROPER PULLING OF WIRES.

27. PROVIDE OUTLET BOX FOR EACH WIRING DEVICE, COMMUNICATION OUTLET AND AS INDICATED.

USE ELECTRO-GALVANIZED STEEL BOXES. PROVIDE GANG BOXES WHERE WIRING DEVICES ARE

GROUPED. SUPPORT BOXES INDEPENDENTLY OF CONNECTION CONDUITS. DO NOT INSTALL

OUTLET BOXES BACK-TO-BACK IN WALLS. SUCH OUTLETS MUST BE STAGGERED AND SEALED

AGAINST NOISE TRANSMISSION.

28. 120V SINGLE POLE SWITCHES: HUBBELL CAT. #1201-I, 15A (OR APPROVED EQUAL).

29. 120V SINGLE POLE 3-WAY SWITCHES: HUBBELL CAT. #1203-I, 15A (OR APPROVED EQUAL).

30. DUPLEX RECEPTACLES: 15A, 125A, 3 WIRE GROUNDING TYPE: HUBBELL CAT. #5262-I (OR

APPROVED EQUAL).

31. SINGLE RECEPTACLES: 15A, 125A, 3 WIRE GROUNDING TYPE: HUBBELL CAT. #5261-I (OR

APPROVED EQUAL).

32. COVER PLATES FOR RECESSED BOXES: WHITE.

33. COVER PLATES FOR SURFACE MOUNTED BOXES: GALVANIZED FORMED STEEL TYPE.

34. USE GANG PLATES WHERE TWO OR MORE OUTLETS ARE LOCATED TOGETHER. ALIGN ALL

COVER PLATES PARALLEL AND PERPENDICULAR TO BUILDING LINES. PROVIDE BLANK COVER

PLATES FOR BOXES WITHOUT WIRING DEVICES.

35. PROVIDE LIGHTING FIXTURES AND LAMPS AS INDICATED. ACRYLIC LENSES AND DIFFUSERS

WITH FLAME SPREAD NOT MORE THAN 250, SMOKE DEVELOPMENT CLASSIFICATION NOT MORE

THAN 600, TO ULC S102-3, AS INDICATED. SUPPORT ALL SUSPENDED LUMINAIRES, INCLUDING

LUMINAIRES INSTALLED IN SUSPENDED CEILING DIRECTLY FROM BUILDING STRUCTURE ON #12

JACK CHAINS AND #11 S-HOOKS CAPABLE OF SUPPORTING TEN TIMES LUMINAIRE WEIGHT.

36. WIRING TO EMERGENCY/EXIT LIGHTING FIXTURES SHALL BE SIZED, AND CIRCUITS SO

ARRANGED IN ORDER NOT TO EXCEED 5% VOLTAGE DROP.

37. PROVIDE 7 DAY PROGRAMMABLE ELECTONIC TIME SWITCH " PARAGON EC 7000 -120V SERIES"

OR EQUAL.

38. CONTACTORS FOR LIGHTING LOADS: SQUARE-D, CLASS 8903, TYPE L, ELECTRICALLY HELD IN

CSA I ENCLOSURE. CONTACTORS TO BE PRODUCT OF ONE MANUFACTURER. ACCEPTABLE

MANUFACTURERS: SIEMENS, KLOCKNER & MOELLER, ASCO.

39. DIVISION 15 SHALL PROVIDE ELECTRIC MOTORS, MOTORIZED VALVES AND DAMPERS WITH

TRANSFORMER, LOW VOLTAGE THERMOSTATS, FLOAT SWITCHES, PRESSURE SWITCHES, FLOW

SWITCHES AND INTERLOCKS. INSTALL STARTERS, CONTROL PANELS AND LINE VOLTAGE

THERMOSTATS SUPPLIED BY DIVISION 15. PROVIDE POWER WIRING INCLUDING WIRING OF LINE

VOLTAGE CONTROLS, THERMOSTATS, SPEED CONTROLLERS, STARTERS AND DISCONNECT

SWITCHES CONNECTED IN LINE BETWEEN POWER SOURCE AND MOTOR. VERIFY ON SITE

EXACT LOCATION AND POWER SUPPLY REQUIREMENTS OF ALL MECHANICAL EQUIPMENT

BEFORE PROCEEDING WITH RELATED WORK. NOTIFY CONSULTANT OF ANY DISCREPANCIES.

40. VERIFY EXACT LOCATION AND POWER REQUIREMENTS OF ALL TENANT'S SUPPLIED EQUIPMENT

BEFORE PROCEEDING WITH RELATED WORK. NOTIFY CONSULTANT OF ANY DISCREPANCIES.

41. PROVIDE TEMPORARY ELECTRICAL POWER FOR THE WORK OF OF THE TRADES AS REQUIRED BY

GENERAL CONTACTOR.

42. SUBMIT 3 COPIES OF SHOP DRAWINGS F0R APPROVAL OF ALL FQUIPMENT AND LIGHTING

FIXTURES,

43. SUBMIT "AS BUILT DRAWINGS" WITH ONE SET OF MARK UP SEPIAS TO OWNER AFTER

COMPLETION OF WORKS

44. ALL ELECTRICAL WORK SHALL BE WARRANTED TO BE FREE FROM DEFECTS IN MATERIAL AND

WORKMANSHIP FOR A PERIOD OF ONE YEAR FROM THE DATE OF SUBSTANTIAL PERFORMANCE.

AT NO COST TO THE OWNER, CORRECT ANY DEFECTS IN THE ELECTRICAL WORK THAT ARE

IDENTIFIED WITHIN THAT PERIOD OF TIME.

45. THE ELECTRICAL CONTRACTOR SHALL MAINTAIN ACCIDENT AND CONSTRUCTION LIABILITY

INSURANCE TO THE LIMITS REQUIRED FOR THE PROJECT IN ORDER TO PROTECT ALL

CONTRACTUAL PARTIES.

46. ANY ELECTRICAL CONDUIT, WIRE PENETRATION THROUGH FIRE RATED WALL TO BE PROPERLY

FIRESTOPPED WITH APPROPRIATE FIRE STOP MATERIAL.

LEGEND

SYMBOL DESCRIPTION

SINGLE POLE TOGGLE SWITCH GANGED AS SHOWN, HUBBELL No.18201-1(347V), No. CSB115-1(120V).

THREE WAY TOGGLE SWITCH, HUBBELL No. 18203-1(347V), No. CSB3151(120V).

FOUR WAY TOGGLE SWITCH, HUBBELL No. 18204-1(347V), No. CSB4151(120V).

WALL MOUNTED OCCUPANCY SENSOR SWITCH. WATTSTOPPER WS-200 OR APPROVED EQUAL.

CEILING MOUNTED OCCUPANCY SENSOR SWITCH. WATTSTOPPER CI-200 OR APPROVED EQUAL.

15A 120V 1PH GROUNDED DUPLEX RECEPTACLE, HUBBELL No. BR15.

SPLIT DUPLEX RECEPTACLE

DUPLEX RECEPTACLE MOUNTED ABOVE COUNTER

QUADRUPLEX RECEPTACLE

SPECIAL RECEPTACLE AS INDICATED ON DRAWING

15A 120V 1PH ISOLATED GROUND DUPLEX RECEPTACLE, HUBBELL No.IG-5252 PROVIDE SEPARATE NEUTRAL

AND GROUND WIRE FOR EACH OUTLET.

15A 120V 1PH GFCI GROUNDED DUPLEX RECEPTACLE, HUBBELL No. GFR5262.

20A 120V 1PH GROUNDED DUPLEX RECEPTACLE, HUBBELL No. BR20.

20A 120V 1PH GFCI GROUNDED DUPLEX RECEPTACLE, HUBBELL No. GFR5362.

15A 250V 1PH GROUNDED DUPLEX RECEPTACLE, HUBBELL No. HBL5462. (NEMA 6-15R)

20A 250V 1PH GROUNDED DUPLEX RECEPTACLE, HUBBELL No. HBL5462. (NEMA 6-20R)

20A 125/250V 1PH 4W GROUNDED SINGLE RECEPTACLE, HUBBELL No. HBL8410.

30A 250V 1PH 3W GROUNDED SINGLE RECEPTACLE, HUBBELL No. 9330.

30A 250V 3PH 4W GROUNDED SINGLE RECEPTACLE, HUBBELL No. HBL8430A.

15A 120V 1PH GROUNDED DUPLEX RECEPTACLE, HUBBELL No. CBR15IC SIMPLE GANGED, DOUBLE FACED,

SURFACE FLOOR MOUNTED IN A WALKER No. 525G OUTLET ON A WALKER No. 800 FLOOR BOX C/W 825SFCK

CONVERSION KIT.

HUBBELL No.CBR15IC SIMPLE GANGED, DOUBLE FACED, SURFACE FLOOR MOUNTED IN WALKER No.525G

OUTLET ON A WALKER No.800 FLOOR BOX C/W 825SFCK CONVERSION KIT

JUNCTION BOX MOUNTED ON UNDERSIDE ON ROOF DECK FOR CONNECTION/EXTENSION TO DEALERS

EQUIPMENT BELOW

120V 1PH CONNECTION TO EQUIPMENT AS NOTED.





DISCONNECT SWITCH.

SINGLE PHASE MANUAL MOTOR STARTER SWITCH SUPPLIED BY MECHANICAL CONTRACTOR INSTALLED AND

WIRED BY ELECTRICAL CONTRACTOR.

SINGLE PHASE MAGNETIC MOTOR STARTER SWITCH SUPPLIED BY MECHANICAL CONTRACTOR INSTALLED AND


THREE PHASE MAGNETIC MOTOR STARTER SWITCH SUPPLIED BY MECHANICAL CONTRACTOR INSTALLED AND


THERMOSTAT FOR ELECTRICAL HEATERS SUPPLIED AND INSTALLED BY ELECTRICAL CONTRACTOR.

SPEED CONTROL SUPPLIED BY MECHANICAL CONTRACTOR INSTALLED AND WIRED IN POWER CIRCUITS BY

ELECTRICAL CONTRACTOR.

ELECTRIC HEATER (1KW) REFER TO ELECTRICAL HEATER SCHEDULE.

LIGHTING PANEL OR RECEPTACLE PANEL AS NOTED. LP DENOTES LIGHTING PANEL, RP DENOTES RECEPTACLE

PANEL.

UF UNFUSED.

WP DENOTES WEATHERPROOF.

NL DENOTES NIGHT LIGHT.

EM1-1 DENOTES EMERGENCY LIGHTING CCT No.1 FROM EMERGENCY BATTERY SOURCE 'EM1'.

A-1 DENOTES CIRCUIT No.1 FROM PANEL 'A'

VOICE OUTLET WALL MOUNTED.

DATA OUTLET WALL MOUNTED.

COMBINED VOICE/DATA OUTLET WALL MOUNTED.

VOICE OUTLET FLOOR MOUNTED WALKER No. 886B FLOOR BOX C/W ADAPTOR AND No. 525C OUTLET.

COMBINED VOICE/DATA OUTLET FLOOR MOUNTED WALKER No. 886B FLOOR BOX C/W ADAPTOR AND No. 525C

OUTLET.

COMBINED VOICE/DATA OUTLET FLOOR MOUNTED WALKER No. 886B FLOOR BOX C/W ADAPTOR AND No. 895GF1

OUTLET.

FIRE ALARM PULL STATION

FIRE ALARM HORN/STROBE COMBO

FIRE ALARM STROBE

FIRE ALARM IONIZATION SMOKE DETECTOR SURFACE MOUNTED

FIRE ALARM HEAT DETECTOR COMBINATION 135°F FIXED TEMP. & RATE OF RISE.

FIRE ALARM HEAT DETECTOR 200°F FIXED TEMP.

EMERGENCY LIGHTING DOUBLE SURFACE MOUNTED 12V 5W, LED REMOTE HEAD. BEGHELLI

#BTMR2-LED-12V-5W OR EQUAL. BLACK FINISH FOR FRONT OF HOUSE AND WHITE FINISH FOR BACK OF HOUSE.

WALL/COLUMN (MOUNTED AT 96") OR CEILING MOUNTED GREEN PICTOGRAM EXIT SIGN, 120V OR 347V. ALL STEEL

LED RUNNING MAN SIGN. BEGHELLI #QR-RM LU0LRM-UDC OR EQUAL. WHITE FINISH FOR BACK OF HOUSE.

WALL/COLUMN (MOUNTED AT 96") OR CEILING MOUNTED GREEN PICTOGRAM EXIT SIGN, 120V OR 347V. EXTRUDED

ALUMINUM LED RUNNING MAN SIGN. BEGHELLI #QR-RM LU0LRM-UDC OR EQUAL. BLACK FINISH FOR FRONT OF

HOUSE AND WHITE FINISH FOR BACK OF HOUSE.

WALL/COLUMN (MOUNTED AT 96") OR CEILING MOUNTED GREEN PICTOGRAM COMBO SIGN, 120V OR 347V.

EXTRUDED ALUMINUM LED RUNNING MAN COMBO. BEGHELLI #QR-RM-12-72-L-1-0LR-M-BTMR2-5W OR EQUAL.

BLACK FINISH FOR FRONT OF HOUSE AND WHITE FINISH FOR BACK OF HOUSE.

CENTRAL EMERGENCY BATTERY UNIT AS NOTED ON DRAWING SHALL BE EQUAL TO BEGHELLI NOVA SERIES

CATALOG #NV12-200-(BTMR2-5W-LD)-AT-FD5, 12V DC, CAPACITY AS SPECIFIED ON DRAWING, SEALED LEAD

BATTERY, 5 CIRCUITS FUSED (10A) PANELBOARD, AUTO-TEST SELF DIAGNOSTICS, AND (IF INDICATED ON

DRAWING, 2-5W LED REMOTE HEADS AND L.V. DISCONNECT SWITCH ) AND MOUNTING PLATFORM. MOUNT

BATTERY AT 96" A.F.F. POST MAINTENANCE INSTRUCTIONS ON FRONT OF UNIT. BATTERY UNIT SHALL BE FOR

OPERATION AT 120V OR 347V AC.

GENERAL NOTE FOR ALL DRAWINGS

THESE DRAWINGS ARE DIAGRAMMATIC ONLY. BEFORE ANY OUTLET IS ROUGHED IN, ITS EXACT LOCATION MUST BE

DETERMINED FROM THE ARCHITECTURAL DRAWINGS (REFLECTED CEILING PLANS), ARCHITECTURAL ELEVATIONS,

STORE PLANNING ELEVATIONS OR DETAILED ELEVATIONS ON THE ELECTRICAL DRAWINGS. WHERE THIS INFORMATION

IS NOT SHOWN ON THE DRAWINGS VERIFY IN EACH INSTANCE THE EXACT LOCATION WITH THE PROJECT MANAGER ON

THE JOB SITE.

PART 1- GENERAL

1.1 RELATED WORK

.1 NOT USED.

1.2 DESCRIPTION OF SYSTEM

.1 SYSTEM INCLUDES:

.1 CONNECTION TO CONTROL PANEL TO CARRY OUT FIRE ALARM

AND PROTECTION FUNCTIONS INCLUDING RECEIVING ALARM

SIGNALS, INITIATING GENERAL ALARM, SUPERVISING SYSTEM

CONTINUOUSLY, ACTUATING ZONE ANNUNCIATORS, AND

INITIATING TROUBLE SIGNALS.

.1 TROUBLE SIGNAL DEVICES.

.2 MANUAL ALARM STATIONS.

.3 AUTOMATIC ALARM INITIATING DEVICES.

.4 AUDIBLE SIGNAL DEVICES.

.5 END-OF-LINE DEVICES.

.6 VISUAL ALARM SIGNAL DEVICES.

.7 AUXILIARY DEVICES.

.2 OPERATION OF ANY ALARM INITIATING DEVICE TO

SPECIFICATIONS:

PART 2- PRODUCTS

2.1 MATERIALS

.1 CAN/ULC-S524-01 ENTIRE SYSTEM INSTALLATION.

.2 CAN/ULC-S527-1999 CONTROL UNITS FOR FIRE ALARM SYSTEMS.

.3 CAN/ULC-S529-M87 SMOKE DETECTORS FOR FIRE ALARM

SYSTEMS.

.4 CAN/ULC-S529-M87 SMOKE DETECTORS FOR FIRE ALARM

SYSTEMS.

.5 CAN/ULC-S525-M91 HEAT DETECTORS FOR FIRE ALARM SYSTEMS.

.6 CAN/ULC-S525-99 AUDIBLE SIGNALING DEVICES FOR FIRE ALARM

SYSTEMS.

.7 CAN/ULC-S5260M87 VISUAL SIGNALING APPLIANCES FOR FIRE

ALARM SYSTEMS.

.8 CAN/ULC-S548-M90 MANUAL PULL STATIONS FOR FIRE ALARM

SYSTEMS.

.9 CAN/ULC-S548-M90 WATER FLOW INDICATORS FOR FIRE ALARM

SYSTEMS.

2.4 MANUAL ALARM STATIONS

.1 MANUAL ALARM STATIONS: PULL LEVER, BREAK GLASS, WALL

MOUNTED SURFACE TYPE, NON-CODED SINGLE POLE NORMALLY

OPEN CONTACT.

2.5 AUTOMATIC ALARM INITIATING DEVICES

.1 HEAT DETECTORS, FIXED TEMPERATURE, SELF-RESTORING,

RATED 57C.

.2 THERMAL FIRE DETECTORS, COMBINATION FIXED TEMPERATURE

AND RATE OF RISE, NON-RESTORABLE FIXED TEMPERATURE

ELEMENT, SELF-RESTORING RATE OF RISE, FIXED TEMPERATURE

50ºC, RATE OF RISE 9.4ºC PER MIN.

.3 SMOKE DETECTOR: PHOTO-ELECTRIC TYPE.

.4 SMOKE DETECTOR: IONIZATION TYPE (AIR DUCT TYPE WITH

SAMPLING TUBES).

2.6 AUDIBLE SIGNAL DEVICES

.1 HORNS: 91-95 DB AT 3,000 MM SURFACE MOTORIZED 24 V DC

.2 HORNS/STROBES: 91-95 DB AT 3,000 MM SURFACE MOTORIZED

24V DC.

.3 SPEAKERS: 91-95 DB AT 3,000 MM SURFACE MOTORIZED 24 V DC,

200 MM.

2.7 END-OF-LINE DEVICES

.1 END-OF-LINE DEVICES TO CONTROL SUPERVISORY CURRENT IN

ALARM CIRCUITS AND SIGNALING CIRCUITS, SIZED TO ENSURE

CORRECT SUPERVISORY CURRENT FOR EACH CIRCUIT. OPEN,

SHORT OR GROUND FAULT IN ANY CIRCUIT WILL ALTER REMOTE

ANNUNCIATOR AS INDICATED.

PART 3- EXECUTION

3.1 INSTALLATION

.1 INSTALL SYSTEM IN ACCORDANCE WITH CAN/ULC-S524-01.

.2 LOCATE AND INSTALL MANUAL ALARM STATIONS AS INDICATED,

AND CONNECT TO ALARM CIRCUIT WIRING.

.3 LOCATE AND INSTALL THERMAL AND SMOKE DETECTORS AS

INDICATED AND CONNECT TO ALARM CIRCUIT WIRING.

.4 CONNECT ALARM CIRCUIT TO MAIN CONTROL PANEL.

.5 LOCATE AND INSTALL SPEAKERS AS INDICATED AND CONNECT TO

SIGNALING CIRCUITS.

.6 CONNECT SIGNALING CIRCUITS TO MAIN CONTROL PANEL.

.7 CONNECT SUPERVISORY DEVICES TO MAIN CONTROL PANEL.

.8 INSTALL END-OF-LINE DEVICES AT END OF ALARM AND SIGNALING

CIRCUITS AS INDICATED.

.10 LOCATE AND INSTALL REMOTE RELAY UNITS TO CONTROL FAN

SHUT DOWN AS REQUIRED.

.11 ALL WIRING SHALL BE INSTALLED ACCORDING TO CEC

STANDARDS AND PER DRAWINGS, UNLESS NOTED OTHERWISE.

.12 NOT USED.

.13 THE FIRE ALARM ZONES MUST BE CONNECTED TO THE FIRE

ALARM SYSTEM.

.14 THE KITCHEN FIRE SUPPRESSION SYSTEM MUST BE CONNECTED

TO THE FIRE ALARM SYSTEM.

.15 NOT USED.

.16 NOT USED.

.17 ALL ELECTRICAL COOKING EQUIPMENT MOUNTED BELOW THE

EXHAUST HOOD SUPPRESSION SYSTEM MUST BE CONTROLLED BY

A SHUNT TRIP SOLENIOD TO TRIP WHEN THE HOOD SUPPRESSION

SYSTEM RELEASES.

.18 NOT USED.

.19 NOT USED.

3.2 TESTS

.1 EQUIPMENT MANUFACTURER TO PERFORM TESTS IN

ACCORDANCE WITH CAN/ULC-S537-97.

.2 FIRE ALARM SYSTEM:

.1 TEST EACH DEVICE AND ALARM CIRCUIT TO ENSURE MANUAL

STATIONS, THERMAL AND SMOKE DETECTORS, SPRINKLER SYSTEM

TRANSMIT ALARM TO CONTROL PANEL AND ACTUATE GENERAL

ALARM AND ANCILLARY DEVICES.

.3 SIMULATE GROUNDS AND BREAKS ON ALARM AND SIGNALING

CIRCUITS TO ENSURE PROPER OPERATION OF TROUBLE SIGNALS.

3.3 CERTIFICATE OF VERIFICATION

.1 ON COMPLETION OF ALL TESTS, EQUIPMENT MANUFACTURER TO

PROVIDE CERTIFICATE OF VERIFICATION CONFIRMING THAT ALL

EQUIPMENT HAS BEEN INSTALLED IN ACCORDANCE WITH

MANUFACTURER'S RECOMMENDATION. PROOF OF LIABILITY

INSURANCE FOR THE INSPECTION MUST BE INCLUDED.

.2 PROVIDE THIRD PARTY VERIFICATION OF THE ACTIVE SYSTEM.

3.4 APPROVED MANUFACTURER SHALL BE CHUBB-EDWARDS,

NOTIFIER, SIMPLEX.

ELECTRICAL DRAWING LIST

E0.1ELECTRICAL LEGEND, DRAWING LIST AND SPECIFICATION

E1.1 GROUND FLOOR PLAN - LIGHTING LAYOUT

E1.2 GROUND FLOOR PLAN - POWER AND SYSTEMS LAYOUT

E1.3 GROUND FLOOR PLAN - KITCHEN LAYOUT

E1.4 ROOF ELECTRICAL LAYOUT

E1.5 ELECTRICAL DETAILS

E1.6 ELECTRICAL DETAILS

E1.7 POWER DISTRIBUTION AND FIRE ALARM RISER

E1.8 KITCHEN EQUIPMENT SCHEDULE & ELEVATION AND LUMINAIRE SCHEDULE

E1.9 PANEL SCHEDULE

POS CABLING SCOPE OF WORK

NOTE: PLEASE REFER TO THE POS FLOOR PLAN, AND DATA DROP CHART FOR DETAILED INFORMATION AND LOCATION OF THE EQUIPMENT.

CABLING SPECIFICATIONS

THE GENERAL CONTRACTOR (GC) IS TO INSTALL CONDUITS, PULL DATA AND VOICE CABLES & TERMINATE TO THESE SPECIFICATIONS:

1. ALL CABLE IS TO BE CERTIFIED CAT5E BELDEN OR HUBBELL BRANDED CABLE

2. LABELING:

a. EACH NETWORK FACEPLATE IS TO BE LABELED WITH A MACHINE PRINTED MYLAR LABEL

b. EACH PORT ON THE PATCH PANEL IS TO BE LABELED WITH A MACHINE PRINTED MYLAR LABEL

c. BOTH ENDS OF CABLES ARE TO BE LABELED WITH A MACHINE PRINTED MYLAR LABEL

AN APPROPRIATE NAMING/NUMBERING CONVENTION IS TO BE USED.

3. GUARANTEE/WARRANTY

a. THE STRUCTURED CABLING SHALL BE WARRANTED FOR MINIMUM OF 15 YEARS

b. THE CABLING SYSTEMS EXCEED THE APPROPRIATE ISO/IEC/ANSI/TIA SPECIFICATIONS

c. THE REPLACEMENT AND REPAIR OF ANY ORIGINALLY INSTALLED CABLING COMPONENT SHALL BE COMPLETED AT NO COST FOR PARTS

AND LABOUR TO THE OWNER DURING THE 15 YEAR WARRANTY PERIOD. ANY COMPONENTS REPAIRED OR REPLACED SHALL BE

WARRANTIED FOR A) 90 DAYS OR B) THE REMAINDER OF THE 15 YEAR WARRANTY, WHICHEVER IS LONGER.

d. A GUARANTEE/WARRANTY CERTIFICATE FOR THE ORIGINAL INSTALLATION SHALL BE ISSUED TO THE OWNER BY THE SYSTEM SUPPLIER

STATION CABLING - POS/PRINTER/ETC.

PROVIDE ONE (1) 4PR CAT5E FT6 UTP CABLE FROM THE COMMUNICATION BACKBOARD IN MANAGER'S OFFICE CLOSET TO EACH POS DEVICE,

REMOTE PRINTER, AP LOCATION AND VOICE SET WITHIN THE STORE.

TERMINATE THE DEVICE END (FOR POS\PRINTER ETC. EQUIPMENT) OF EACH CABLE WITH ONE (1) RJ45 CAT5E INSERT C\W FACEPLATE OR

SURFACE MOUNT BOX AS REQUIRED.

TERMINATE THE DEVICE END (FOR TELEPHONE EQUIPMENT) OF EACH CABLE WITH ONE (1) RJ11 CAT5E INSERT C\W FACEPLATE OR SURFACE

MOUNT BOX AS REQUIRED.

BACKBOARD

SUPPLY AND INSTALL ONE (1) 48-PORT BELDEN OR HUBBELL PATCH PANEL IN A (1) 2U WALL MOUNT BRACKET.

ALL STATION CABLES ARE TO BE TERMINATED TO THE ABOVE MENTIONED PATCH PANEL AS PER THE SPECIFICATIONS ABOVE.

INCENTIVE REQUIRED DOCUMENTATION

NOTE: PENDING RECEIPT OF THE FOLLOWING DOCUMENTATION, THE SUM OF TEN THOUSAND DOLLARS ($10,000.00) WILL BE HELD BACK

FROM THE CONTRACTOR PRICE AND WILL ONLY BE ADVANCED AND PAID WHEN ALL REQUIRED DOCUMENTATION HAS BEEN RECEIVED

WITHIN THE REQUIRED TIME PERIOD IN PROPER FORM FOR THE PURPOSE OF APPLICABLE INCENTIVE APPLICATIONS:

INCENTIVES:

1. ESTIMATED TOTAL PROJECT COST (INCLUDES CONSTRUCTION & EQUIPMENT COSTS).

2. PURCHASE ORDERS DETAILS EQUIPMENT TO BE INSTALLED (ERV UNITS, LIGHTING, AC UNITS, AS REQUESTED).

3. EQUIPMENT COST ESTIMATES, QUOTES AND/OR PROPOSALS.

4. CUTSHEETS OR DETAILED MANUFACTURERS DATA FOR EQUIPMENT SPECIFIED FOR INCENTIVES.

5. ESTIMATED INCREMENTAL COSTS OF EQUIPMENT & LABOUR (BASE CASE-ENERGY EFFICIENT CASE I.E. GEOTHERMAL).

6. DOCUMENTATION OF CONTROLLED SEQUENCES FOR BUILDING EQUIPMENT (I.E. HEAT LOAD CALCULATIONS, IF A PROJECT INCLUDES BOILER DOCUMENTATION OF COMBUSTION

ANALYSIS PRINTOUTS AND START-UP REPORTS PER BOILER WILL BE REQUIRED).

7. DOCUMENTED PERCENT OF OUTSIDE AIR ON AIR RETURN SYSTEMS.

8. FOLLOWING PROJECT COMPLETION, INVOICES SHOWING PROOF OF PAYMENT TO BE SUBMITTED AS REQUESTED:

1. ALL INVOICES NEED TO SPECIFY THE MANUFACTURERS MODEL NUMBER FOR EVERY PIECE OF EQUIPMENT.

2. ALL INVOICES FOR THE LIGHTING FIXTURES INSTALLED SHOULD SHOW THE QUANTITY AND TYPE OF FIXTURES SO THAT THEY MATCH THE 'LUMINAIRE SCHEDULE' IN THE

ELECTRICAL DRAWINGS.

ELECTRICAL SPECIFICATIONSFIRE ALARM SPECIFICATIONS

POS SPECIFICATIONS

E0.1

Key Plan

General Notes

DO NOT SCALE DRAWINGS. USE ONLY DRAWINGS

MARKED "ISSUED FOR CONSTRUCTION". VERIFY

CONFIGURATIONS & DIMENSIONS ON SITE BEFORE

BEGINNING WORK. NOTIFY ARCHITECT IMMEDIATELY

OF ANY ERRORS, OMISSIONS OR DISCREPANCIES.

CHAMBERLAIN ARCHITECT SERVICES LIMITED AND

CHAMBERLAIN CONSTRUCTION SERVICES LIMITED

HAVE SIMILAR OWNERSHIP.

Architect

Note to Sub-Contractors:

FOR ADDITIONAL INFORMATION, BIDDER'S

LIST, ETC CONTACT:

BARBARA FREEDMAN, CONSTRUCTION

COORDINATOR

CARA OPERATIONS LIMITED

(905) 760-2244 EXT. 2269

KS

IS14-209

14-209

PRINCE ALBERT, SASKATCHEWAN

OPERATIONSLIMITED

199 Four Valley DriveVaughan, Ontario L4K 0B8Phone: (905) 760-2244

27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY

www.invirosystems.ca

Architect

T-4A T-4A T-4A T-4A T-4A

T-4A

T-4A

T-4

T-4A

T-4

T-4 T-4

T-5T-5

T-10

T-2

T-2

T-2

T-2

T-2

T-2

T-2

T-2

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-1

T-1

T-3 T-3

T-3T-3

T-6

T-8T-8

T-9

T-4A

T-8

T-6

KEY NOTES

LIGHTING CONTACTOR SCHEDULE

LIGHTING CIRCUITS

DIMMER CCT # TYPE

LOAD (W)

LUTRON MODEL #

DM1 B-13 LT13 387 DVCL-253P

DM2 B-15 LT4C 195 DVCL-253P

DM3 B-15 LT4A 130 DVCL-253P

DM4 B-15 LT4B 156 DVCL-253P

DM5 B-17 LT8 120 DVCL-253P

DM6 B-17 LT8 160 DVCL-253P

DM7 B-19 LT5 208 DVCL-253P

DM8 B-19 LT11 120 DVCL-253P

DM9 B-15 LT4C 117 DVCL-253P

DM10 B-19 LT1 24 DVCL-253P

DM11 B-13 LT13 129 DVCL-253P

DM12 B-13 LT9 129 DVCL-253P

DM13 B-17 LT8 160 DVCL-253P

DM14 B-23 LT13 129 DVCL-253P

DM15 B-23 LT10 330 DVCL-253P

DM16 B-25 LT8 200 DVCL-253P

DM17 B-27 LT4E 234 DVCL-253P

DM18 B-29 LT6 180.6 DVLV-10P

DM19 B-25 LT5 91 DVCL-253P

DM20 B-25 LT5 39 DVCL-253P

NOTES

1. CONFIRM HARDWARE REQUIREMENTS WITH MANUFACTURER PRIOR TO ORDERING. SEE

MANUFACTURER'S INSTRUCTION FOR CONNECTION DETAILS.

2. WHITE COLOUR FINISH FOR DIMMER AND WALL PLATES.

3. USE MULTI-GANG WALLPLATES AS REQUIRED.

GROUND FLOOR PLAN : LIGHTING LAYOUT

E1.1

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

COMMUNICATIONS BACKBOARD LAYOUT

E1.2

1

GROUND FLOOR PLAN : POWER & SYSTEMS LAYOUT

MANAGER'S OFFICE PART PLAN

E1.2

2

E1.2

2

DOOR PUSHBUTTON WIRING DIAGRAM

E1.2

3

ELECTRIC HEATER SCHEDULE

TYPE WATT VOLTS/ PHASE MANUFACTURER REMARKS

500 208V/1PH

STELPRO, OUELLET, OR

DIMPLEX EQUIVALENT

STELPRO 'B' SERIES BASEBOARD HTR C/W BUILT-IN

THERMOSTAT (SEE NOTE 2 & 3)

1000 208V/1PH


DIMPLEX EQUIVALENT



2000 208V/1PH


DIMPLEX EQUIVALENT



2000 208V/1PH


DIMPLEX EQUIVALENT

STELPRO 'WF' WALL FAN HEATER FLUSH MT'D C/W BUILT-IN

THERMOSTAT (SEE NOTE 1)

2000 208V/1PH


DIMPLEX EQUIVALENT

STELPRO 'CF' CEILING MOUNTED FAN HEATER FLUSH MT'D C/W

BUILT-IN THERMOSTAT (SEE NOTE 1)

4000 208V/1PH


DIMPLEX EQUIVALENT

STELPRO 'WF' WALL FAN HEATER FLUSH MT'D C/W BUILT-IN

THERMOSTAT (SEE NOTE 1)

NOTES

1. SET THERMOSTAT AT 15°C.

2. SET THERMOSTAT AT 18°C.

3. ALL BASEBOARD HEATERS SHALL BE MOUNTED 50mm A.F.F. TO BOTTOM OF HEATER (OR AS NOTED ON PLAN).

4. BLACK FINISH IN PUBLIC AREAS AND WHITE FINISH IN BACK OF HOUSE. VERIFY COLOUR FINISH WITH ARCHITECT

BEFORE ORDERING.

GENERAL NOTES

KEY NOTES

E1.2

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

T-4A T-4A T-4A T-4A T-4A

T-4A

T-4A

T-4

T-4A

T-4

T-4 T-4

T-5T-5

T-10

T-2

T-2

T-2

T-2

T-2

T-2

T-2

T-2

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-2A

T-1

T-1

T-3 T-3

T-3T-3

T-6

T-8T-8

T-9

T-4A

T-8

T-6

KEY NOTES

FIRE SUPPRESSION PULL STATION

E1.3

1

GROUND FLOOR PLAN : KITCHEN LAYOUT

PULL

82B

12

83 818282A

81

8282A

15

19

18

47

48

7070A

71 71A

4142

44

46

43

102

43A

35

9411097A95

1

23

ABOVE COOLER

113 114

72

50

32

21

23A

22A

22B

23A

32

25

26

27

28

29

23A

34

33

GENERAL NOTES

31

31

31

31

E1.3

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

ROOF PLAN : POWER & SYSTEMS LAYOUT

E1.4

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

E1.5

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

1 DCV-3111

Utility Cabinet Right

Utility Cabinet Right

Hood # 2

1 Light

1 Fan

Smart Controls DCV

Exhaust

Exhaust

Exhaust

Supply

3

3

3

3

3.000

2.000

1.500

5.000

575

575

575

575

3.1

2.2

1.6

5.0

NO. TAG PACKAGE # LOCATION

SWITCHES

LOCATION QUANTITY

OPTION

FANS CONTROLLED

TYPE Ø H.P. VOLT FLA

C NO

DESCRIPTION OF OPERATION:

8/11/2014

INSTALL

ECP #1-1

Demand Control Ventilation, w/ 3 Exhaust Fans, 1 Supply Fan, Exhaust on in Fire, Lights out in Fire, Fans modulate

based on duct temperature. INVERTER DUTY THREE PHASE MOTOR REQUIRED! Room temperature sensor shipped loose

for field installation.Verify distance between VFD and Motor; additional cost could apply if distance exceeds 50 feet.

BREAKER PANEL TO HOOD CONTROL PANEL

Responsibility: Electrician

BREAKER PANEL HOOD PANEL

Hot

Neutral

120 V

15 A

Ground

LINE

LINE

575 V

15 AMP

Ground

EXH-1 SM-1

LINE

LINE

LINE

575 V

15 AMP

Ground

EF-2 Righ SM-2

LINE

LINE

LINE

575 V

15 AMP

Ground

EF-3 Prep SM-3

LINE

LINE

LINE

575 V

15 AMP

Ground

MUA SM-4

LINE

Hot

Neutral

115 V

DISH EF AC_1

Ground

15 AMP

HOOD CONTROL PANEL TO FANS / MUA


HOOD PANEL FANS

EXH-101

LOAD LEG 1

LOAD LEG 2

GROUND

FAN:

LOAD LEG 3

EF-2 Righ

02

LOAD LEG 1

LOAD LEG 2

GROUND

FAN:

LOAD LEG 3

EF-3 Prep

03

LOAD LEG 1

LOAD LEG 2

GROUND

FAN:

LOAD LEG 3

LOAD LEG 1

LOAD LEG 2

LOAD LEG 3

GROUND

MUA

05FAN:

120V NEUTRAL

120V HOT

HOOD CONTROL PANEL TO ACCESSORY ITEMS


HOOD PANEL COMPONENT

1:C

4:NO

2:NC

1:C

4:NO

2:NC

1:C

4:NO

2:NC

J4

BLACK

WHITE

GREEN

Hot

Neutral

DISH EF

Ground

AC_1

BLACK

WHITE

GREEN

HOT

NEUTRAL

GROUND

NEUTRAL FROM SHUNT COIL

HOT TO SHUNT COIL

COMMON

NORMALLY OPEN

COMMON

NORMALLY OPEN

COMMON

NORMALLY OPEN

AC_1

DISH EF

100-K12D400

12 AMP

10' 0.00"Nom./10' 0.00"OD

11'-0.00" Overall Length

54"

12"

Utility

Cabinet

28"

22"

9"

12"

28"

44"

9"

12"

28"

44" 22"

9"

12"

28"

16"

5"

Ø8"

33"

5"

Ø8"

33"

5"

Ø8"

33" 17"

5"

Ø8"

MUA Connections

HVAC Connections

8"

27" 27" 27" 27"12" 12"

LIGHTING FOR ACPSP Job # 2111055 - Hood #3

INPUT: 120V AC, 1 Phase, 50/60Hz, 3.5 Watts per light.

TO CONTROL LIGHTS WITH HOOD LIGHT SWITCH, WIRE PER

HOOD ELECTRICAL CONTROL PANEL SCHEMATIC.

TO CONTROL LIGHTS WITH BUILDING LIGHT SWITCH, WIRE

BLACK AND WHITE WIRE TO A 120VAC SERVICE.

END TO END ACPSPS REQUIRE 120VAC FIELD WIRING FROM

J-BOX TO J-BOX. REPLACE LIGHTS WITH LED LIGHTS ONLY.

1" LAYER OF INSULATION FACTORY

INSTALLED IN INTERNAL BACK STANDOFF.

MEETS 0 INCH REQUIREMENTS FOR

CLEARANCE TO COMBUSTIBLE SURFACES.

3"

60" 60"

12"

16"

18"

U.L. Listed Screw In Halogen

Bulb

6' 6.00"Nom./6' 6.00"OD

48"

19 1/2"

24"

10"

10"

39" 19 1/2"

24"

10"

10"

1

2

3

4

EF-1 Left Hood

EF-2 Right Hood

EF-3 Prep Hood

EF-4 Dish Hood

NCA24HPFA

NCA16HPFA

NCA16HPFA

DU50HFA

3425

2333

2000

975

1.500

1.000

1.000

0.650

951

1164

1091

1182

3.000

2.000

1.500

0.500

3

3

3

1

575

575

575

115

3.1

2.2

1.6

5.6

246

210

164

66

19.7

12.2

10.3

9.9

FAN

UNIT

NO.

TAG FAN UNIT MODEL # CFM ESP. RPM H.P. Ø VOLT FLA

WEIGHT (LBS.)

SONES

5 MUA A4-D.1000-920 920 A4-D.1000 8370 0.750 606 5.000 3 575 5.0 1853 17.8

FAN

UNIT

NO.

TAG FAN UNIT MODEL # BLOWER HOUSING CFM ESP. RPM H.P. Ø VOLT FLA

WEIGHT (LBS.)

SONES

REMOTE MANUAL

PULL STATION

REMOVABLE STAINLESS

STEEL SERVICE DOOR

AGENT TANK

OEM RELEASE/

BRACKET ASSEMBLY

PLENUM PROTECTION

NOZZLE

DUCT PROTECTION

NOZZLE

DETECTOR

APPLIANCE PROTECTION

NOZZLE

OPTIONAL PRE-WIRED ELECTRICAL

TERMINAL BOX WITH TERMINAL STRIPS,

3-PHASE CONTACTORS AND OVERLOADS

(IF APPLICABLE)

FAN AND LIGHT

CONTROL PANEL

E1.6

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

FIRE ALARM SYSTEM RISER

E1.7

1

SINGLE LINE DIAGRAM

E1.7

2

SHUNT TRIP CIRCUIT DETAIL

E1.7

3

600A 120/208V 3Ø 4W DISTRIBUTION PANEL 'A' (60CCT)

(MIN. 18 KAIC OR AS PER HYDRO REQUIREMENT, WHICHEVER IS HIGHER)

225A 347/600V 3Ø 4W DISTRIBUTION PANEL 'DP-1A' (42 cct)

(MIN. 22 KAIC OR AS PER HYDRO REQUIREMENT, WHICHEVER IS HIGHER)

LIGHTING CONTACTORS

SUSPENDED 150kVA TRANSFORMER

E1.7

4

E1.7

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

LUMINAIRE SCHEDULE

SYMBOL DESCRIPTION

WALL LANTERN: QUORUM #7500-1-45, BLACK FINISH LAMP: LED12A19/DIM/O/827/G2

DECORATIVE STRING LIGHTS: BARBICAN CUSTOM ANTIQUE COPPER PLATED STEEL SHADED 7.5" DIA,

LAMP: LED, 120V

FOR PATIO - MOUNT TO POST USING METAL SCREW IN HOOKS AT 2400MM AF.F. & TIE BACK TO BUILDING AT 2600MM A.F.F

WALL MOUNTED ALUMINUM FRAME WITH OPAL LENS DIFFUSER AND INTEGRAL 120V DRIVER. BARBICAN LAMP# INTEGRAL 30W LED. REFER TO

EXTERIOR ELEVATIONS FOR LOCATIONS.

TRACK LIGHTING: LITELINE ATHENA BLACK,

HEADS: J-PAR221/30-BK

TRACKS: ATK04-BK (44

1

8

"), ATK06-BK (68

1

8

"), ATK08-BK (92

1

8

") CONNECTORS: ATKP09

LT4A - 44" , 3 HEAD

LT4B - 44" , 2 HEAD

LT4C - 68" LONG, 3 HEAD

LT4D - 68" LONG, 4 HEAD

LT4E - 92" LONG, 5 HEAD

LAMP: PAR 30, LED13PAR30LN/DIM/O/827/NFL25

USE JUNO STYLE TRACK AND CONNECTOR ON DIMMING CIRCUIT

SURFACE MOUNTED DOWN LIGHT: PROGRESS LIGHTING, 5" CYLINDER #P5774-31-75PAR30, BLACK FINISH

LAMP: PAR 30, LED13PAR30LN/DIM/O/827/NFL25

LED TAPE: MAGIC LITE STRIP. INCLUDE ALUMINUM MOUNTING BRACKET AND DRIVERS. 4.3W/ft LED

TABLE LAMP: ROOST ANTLER LAMPS - WALNUT VENEER SHADE WITH ALUMINUM CHROME ANTLERS

SUPPLIED AND INSTALLED BY G.C.

CUSTOM TWIG GLOBE: BARBICAN, 30" DIA. GRAPEVINE SPHERE, TREATED & PRESERVED WITH INTERNAL WIRE FRAME STRUCTURE (BROWN

CORD)

LAMP: MINIATURE LED STRING LIGHT, ALLOW 40W, DIMMABLE SUSPENDED TO HEIGHT INDICATED (ABOVE FINISHED FLOOR)

WALL FIXTURE: RAB VAPOUR-PROOF INCANDESCENT #DVCS100CG, NATURAL ALUMINUM FINISH

LAMP: 43W HALOGEN, #43A/HAL/SSW/4 120V.

CAFE STRING LIGHTS, GALVANIZED FINISH

SUPPLIED AND INSTALLED BY G.C.

MASON JAR CHANDELIER: BARBICAN CUSTOM: LARGE ANTIQUE BLUE MASON JARS IN RECTANGULAR WIRE BASKET

LAMP: WARM WHITE DIMMABLE LED STRING LIGHTS, 60W.

PENDANT: PROGRESS LIGHTING, FRESENEL #P5188-108 C/W ALL REQUIRED MOUNTING ACCESSORIES.

LAMP: 43W HALOGEN, #43A/HAL/SSW/4 120V. ON DIMMING CIRCUIT

MOUNTED 760MM ABOVE TABLE TOP TO U/S OF FIXTURE:

DINING HEIGHT - 1525MM A.F.F

COUNTER HEIGHT - 1675MM A.F.F

BAR HEIGHT - 1830MM A.F.F.

WALL MOUNTED EXTRUDED ALUMINUM LIGHT FIXTURE, LINEAR LIGHTING #RD-L1-10-LED. REFER TO ARCHICTECTURAL EXTERIOR ELEVATIONS

FOR LOCATIONS.

RECESSED DOWN LIGHTS: V3025W-WH, STRAIGHT WHITE BAFFLE WITH WHITE TRIM RING. INSTALL WITH JUNO 6" DELUXE UNIVERSAL HOUSING

SP27917. TRIM TO BE PAINTED SAME COLOUR AS CEILING.

LAMP: PAR 38, 16W LED. LED16PAR38/DIM/830/NFL25

610x1220mm (2'x4') RECESSED FLUORESCENT LIGHT FIXTURE. METALUX #2GR8332AUNVHB81 OR EQUAL

305x1220mm (1'x4') RECESSED FLUORESCENT LIGHT FIXTURE. METALUX #GR8232AUNVHB81 OR EQUAL

UNDERCABINET VALENCE LIGHT FOR MANAGER'S OFFICE. THE LIGHT EDGE #RAP1 4 54 30 MV

C

INCANDESCENT LIGHT FIXTURE,

LAMP: CFL 26W MAX.

WL1

WALL MOUNTED LOW LEVEL FLOOD LIGHT MOUNTED ABOVE CANOPY, CARBON BRONZE FINISH C/W KNUCKLE FLOODLIGHT KIT. XTOR3A C/W

XTORFLD-KNC. LAMP: 30W LED.

WL2 WALL MOUNTED LOW LEVEL FLOOD LIGHT, CARBON BRONZE FINISH. XTOR2A-N. LAMP: 20W LED.

AUDIO SPEAKER SUPPLIED & INSTALLED BY CARA

(2)SP-1 PENDENT (5)SP-2 FLUSH MOUNTED

COLOUR: BLACK. COORINATE LOCATION WITH A/V CONSULTANT

EXTERIOR AUDIO SPEAKER BY CARA MOUNTED BELOW CANOPY. SUPPLIED & INSTALLED BY CARA, COORINATE LOCATION WITH A/V CONSULTANT

AUDIO SPEAKER SUPPLIED & INSTALLED BY CARA. COORDINATE LOCATIONS WITH A/V CONSULTANT

INLINE SPEAKER VOLUME CONTROL SUPPLIED & INSTALLED BY CARA

TELEVISION - REFER TO PLAN FOR SIZE. SUPPLIED & INSTALLED BY CARA

NOTE:

1. ALL LIGHTING FIXTURES ARE SUPPLIED BY ROBERTSON ELECTRIC. CONTACT LISA FRASER AT 416-948-0760 OR [email protected] FOR PRICE AND DELIVERY.

2. ALL FIXTURES TO BE CSA, cUL OR cETL LISTED.

3. ALL LAMPS SHALL BE PHILIPS, G.E. OR OSRAM SYLVANIA UNLESS OTHERWISE NOTED.

4. ALL BALLASTS SHALL BE ELECTRONIC UNLESS OTHERWISE NOTED.

5. GENERAL CONTRACTOR TO CONFIRM LEAD TIME OF ALL LIGHT FIXTURES PRIOR TO COMMENCEMENT OF CONSTRUCTION.

6. ALL OUTDOOR FIXTURES TO HAVE LIQUID-TIGHT CONNECTION.

7. COORDINATE MOUNTING HEIGHT OF FIXTURES WITH ARCHITECTURAL DRAWINGS.

81 COFFEE BREWER 2

BUNN-O-MATIC

AXIOM-DV-TC

KES GC

10mm 1219

13 1

1219 SUPPLY ONLY / SUPPLY CORD AND PLUG INSTALL CORD AND PLUG AND RECPTACLESET IN PLACE - AFTER CLEANING

82 DROP IN POP DISPENSER w/ ICE BIN 2

SERVEND

DI-2323

559x559x886 mm H KES PEPSI

1 @

19mm

407

2.4 120 1

305

5-15P

SUPPLY ONLY - SET UP PEPSI FOR INSTALLATION DUPLEX FROM A1105 TO BE USED FOR THIS PLUG

82A CARBONATOR 2

SIMGO

KES PEPSI

13mm 305

5 120 1

305

5-15P

SUPPLY ONLY - SET UP PEPSI FOR INSTALLATION BX WHIP TO AN OUTLEX BOX IN CABINET

43 DEEP FRYER 3

PITCO

SSH55-C

393x762x914 mm H KES GC 2 120 1

305

5-15P

19mm

80M

267 SET IN PLACE / SUPPLY GAS HOSE KIT

50 DISHWASHER 1

ECOLAB

ES-4000

1117x676x1410 mm H KES GC 19mm

1549

1 @

38mm

142

23 120 1

1511 SET IN PLACE - VENDER TO START UP DIRECT CONNECT

200 AUDIO PACKAGE LOT

BEST BUY

CUSTOM

VARIES KES BB TBD TBD TBD TBDCOORDINATE VENDER INSTALLATION VERIFY POWER LOCATIONSCOORDINATE WITH BEST BUY LOCATIONS OF EQUIPMENT

82B POP RACK 1

SIMGO

CUSTOM

VARIES PEPSI PEPSI13mm 305

5 120 11524

5-15PCOORDINATE VENDER INSTALLATION

28 EXPO COOLER - 1 DOOR - 2 DRAWER 1

DELFIELD

D4460N-24M

1832x800x914 mm H KES KES 11 120 1

305

5-15P

SET IN PLACE - ELECTRICAL TO LOAD CENTER FINAL CONNECTION AT LOAD CENTER

27 EXPO COOLER - 3 DOOR 1

DELFIELD

4472N-30M

1832x800x914 mm H KES KES 12 120 1

305

5-15P


30 EXPO - DROP IN EXPO COOLER 1

DELFIELD

N8118B

660x460x560mm H KES KES

1 @

25mm

610

4 120 1

305

5-15P


35 REFRIGERATED EQUIPMENT STAND 2

DELFIELD

F2962C

1580x790x660 mm H KES KES 8 120 1

305

5-15P

SET IN PLACE

47 FOUR BURNER - OPEN BASE 1

BAKERS PRIDE

24-BP-4B-X

610x974x914 mm H KES GC 3.4 120 1

610

5-15P

19mm

160M


31 EXPO - MICROWAVE OVEN 4

PANASONIC

NE1257

422x549x337 mm H KES GC 17.7 120 1

2020

5-20P

SUPPLY ONLY - ELECTRICAL TO LOAD CENTER FINAL CONNECTION AT LOAD CENTERSET IN PLACE - AFTER CLEANING

72 DISHWASHER STEAM HOOD 1

CAPTIVE AIRE

CUSTOM

GC GC

REFER TO SHOP DRAWINGS - SUPPLY ALL LIGHT BULBSOFF LOAD TRUCK / HANG HOODS / INSTALL SKIRTS / INSTALL ON ROOF

70 EXHAUST HOOD - COOK LINE 1

CAPTIVE AIRE

CUSTOM

GC GC


70A FIRE SUPPRESSION 1

CAPTIVE AIRE

CUSTOM

GC GC

REFER TO SHOP DRAWINGSARRANGE SUPPRESSION TEST / LIGHT PILOTS FOR TEST

25 EXPO - 1 DOOR (LH) 1

DELFILED

4427N-12M

689x914x864 mm H KES KES 7.2 120 1

305

5-15P

SET IN PLACE / RUN WIRING TO LOAD CENTER FINAL CONNECTIONS AT LOAD CENTER

110 DRAFT TOWER 1

DRAFT

SERVICES

DS DS 3 120 1965

5-15PSET UP DRAFT INSTALLATION DATE COORDINATE WITH DRAFT POWER FOR DRAFT TOWERSBEER LINES TO COME UP IN WALL

113 DRAFT - GLYCOL DECK 1

DRAFT

SERVICES

DS DS 7 120 12800

5-15PSUPPLY POWER ABOVE BEER COOLER

114 DRAFT - CONDENSER 1

DRAFT

SERVICES

DS DS 14 120 12800

5-20PSUPPLY POWER ABOVE BEER COOLER

131 SURVEILLANCE SYSTEM 1

BEST BUY

6 CAMERA

OWNER OWNER 5 120 1 5-15PPROVIDE POWER FOR TV AND SYSTEM - COORDINATE WITH OWNERCOORDINATE WITH OWNER

46 CONVECTION OVEN (BOTTOM) 1

BLODGETT

SHO-G

972x937x800 mm H KES GC 6 120 1

626 19mm

50M


46 CONVECTION OVEN (TOP) 1

BLODGETT

SHO-G

972x937x800 mm H KES GC 6 120 1

1462 19mm

50M


15 S/S WORK TABLE c/w GARBAGE AREA 1

TRIMEN

CUSTOM

1524x762x914 mm H KES KES

SET IN PLACE

ITEM

No.

DESCRIPTION

MFG.

MODEL No.

DIMENSIONS

PLUMBING

CWHWDRAIN

ELECTRICAL

HPKW AMP

GAS

GAS

MAN.

BTU

RESPONSIBILITIES

QTY

A.F.FA.F.FA.F.FA.F.F NEMA

GENERAL CONTRACTOR ELECTRICIANK.E.S.

1 WALK IN COOLER 1

CURTIS

CUSTOM

CURTIS CURTIS

SUPPLY ONLY - VENDER TO INSTALL BOX / REFRIGERATION / START UP REFER TO CURTIS SHOP DRAWINGS - SUPPLY ALL LIGHT BULBSSEAL ALL PENETRATIONS / HOIST CONDENSERS ON ROOF

2 WALK IN FREEZER 1

CURTIS

CUSTOM

CURTIS CURTIS

SUPPLY ONLY - VENDER TO INSTALL BOX / REFRIGERATION / START UP REFER TO CURTIS SHOP DRAWINGS - SUPPLY LIGHT BULBSSEAL ALL PENETRATIONS / HOIST CONDENSERS ON ROOF

3 WALK IN BEER COOLER 1

CURTIS

CUSTOM

CURTIS CURTIS

SUPPLY ONLY - VENDER TO INSTALL BOX / REFRIGERATION / START UP REFER TO CURTIS SHOP DRAWINGS - SUPPLY LIGHT BULBSSEAL ALL PENETRATIONS / HOIST CONDENSERS ON ROOF

18 SCICER 1

HOBART

610

KES GC 7 120 1

1219

5-15P

SUPPLY ONLY PUT OUT ON COUTER AFTER CLEANING

19 FOOD PROCESSOR 1

TBD

TBD

CARA CARA 7 120 1

1219

5-15P

PART OF SMALLWARES CARA PACKAGE

21 EXPO - 4 WELL STEAM TABLE W/ FILL 1

TRIMEN

CUSTOM

1478x864x914 mm H KES KES

13mm 450

1@

38mm

450

4 20 208 1

152 SET IN PLACE / RUN WIRING TO LOAD CENTER FINAL CONNECTIONS AT LOAD CENTERDRAIN TO HUB DRAIN

22A EXPO - BUILT IN HOT FOOD WELL 1

TRIMEN

CUSTOM

KES KES

1@

38mm

450

1 5 208 1

152 SET IN PLACE / RUN WIRING TO LOAD CENTER FINAL CONNECTIONS AT LOAD CENTERDRAIN TO HUB DRAIN

22B EXPO - LOAD CENTER 1

TRIMEN

CUSTOM

KES GC 200 1

152 SET IN PLACE ALL FINAL CONNECTIONS AT LOAD CENTER

120/

208

23B EXPO - KDS MONITOR BRACKETS 7

TRIMEN

CUSTOM

KES KES 1 120 1

PART OF OVERSHELF / RUN WIRING TO LOAD CENTER FINAL CONNECTION AT LOAD CENTER

23A EXPO - HEAT LAMPS 6

TRIMEN

CUSTOM

KES KES 5 208 1

PART OF OVERSHELF / RUN WIRING TO LOAD CENTER FINAL CONNECTION AT LOAD CENTER

26 EXPO - THREE DRAWER WARMING UNIT 1

TRIMEN

CUSTOM

KES KES 13 208 1

150 SET IN PLACE / RUN WIRING TO LOAD CENTER FINAL CONNECTIONS AT LOAD CENTER

29 EXPO - WARMING DRAWER 1

WELLS

RW-1

743x546x276mm H KES KES 3.8 120 1 5-15P


32 EXPO - CONVEYOR TOASTER 2

STAR

QCS2-600H

368x621x397mm H KES GC 14 208 1

2020

6-20P

SUPPLY ONLY - ELECTRICAL TO LOAD CENTER FINAL CONNECTION AT LOAD CENTERSET IN PLACE - AFTER CLEANING

41 UNDERCOUNTER FREEZER 1

TRUE

TUC-27F

699x787x864 mm H KES KES 3.2 120 1

305

5-15P

SET IN PLACE

42 FRY WARMER 1

HATCO

GRFHS-21

503x701x552 mm H KES KES 10 120 1

1219

5-15P

SUPPLY ONLY SET IN PLACE - AFTER CLEANING

44 SANDWICH UNIT 1

TRUE

TSSU-27-8

699x787x864 mm H KES KES 3.8 120 1

305

5-15P

SET IN PLACE

48 SMOKER 1

SOUTHERN

SC-200

KES KES 30 1

350 SET IN PLACE DIRECT CONNECT - 4 WIRE

120/

208

120/

208

12 ICE CUBER 1

HOSHIZAKI

KM-900MAH

762x730x953mm H KES GC

13mm 2057

1 @

19mm

1194

13 1

2057 SET IN PLACE DIRECT CONNECTION- 4 WIRE

120/

208

43A PORTABLE FILTER 1

PITCO

P-14

KES KES 5 120 1 5-15P

SUPPLY ONLY PLUG LOCATED NEAR FRYERS

120/

208

83 WAITRESS STATION 2 1

TRIMEN

CUSTOM

KES KESSET IN PLACE PROVIDE DUPLUX ABOUT COUNTER AT 1219mm AFF - GENERIC

97A BAR - OASIS 1

OASIS

TBD

CARA CARA 6 120 1965

5-15P

102 BAR - BACK BAR COOLER - BLACK 1

TRUE

GDM-49

1372x787x2013mm H KES KES 12 120 1457

5-15PSET IN PLACE MAKE SURE FRIDGE CAN FIT WITHIN THE STRUCTURE

33 EXPO - ICE CREAM FREEZER 1

CELCO

CF22SG

546x609x914 mm H KES KES 1.6 120 1

457

5-15P

SET IN PLACE / RUN WIRING TO LOAD CENTER FINAL CONNECTION AT LOAD CENTER

34 PLATE WARMER 1

CARTER HOFFMAN

HP-65

1651x470x508 mm H KES KES 16 120 1

610

5-20P

SET IN PLACE - ELECTRICAL TO LOAD CENTER FINAL CONNECTIONS AT LOAD CENTER

71 EXHAUST HOOD - PREP LINE 1

CAPTIVE AIRE

CUSTOM

GC GC


71A FIRE SUPPRESSION 1

CAPTIVE AIRE

CUSTOM

GC GC

REFER TO SHOP DRAWINGSARRANGE SUPPRESSION TEST / LIGHT PILOTS FOR TEST

92 BAR - COOLER 1

TRUE

TBB-24-48

1248x623x905mm H KES KES 7 120 1457

5-15PSET IN PLACE

94 BAR - GLASS CHILLER 1

TRUE

T50-GC

1261x677x848mm H KES KES 7.6 120 1457

5-15PSET IN PLACE

95 GLASS WASHER 1

ECOLAB

DF

641x638x991mm H KES GC 13mm12mm 140

1 @

38mm

14015 208 1

6106-15P

SET IN PLACE

KITCHEN EQUIPMENT SCHEDULE

43

42

41

3535

46

SCALE:

25

32

262127

28

3132

31

SCALE:

31 31

KDS KDSKDSKDSKDS

23A 23A 23A

30 22B22A

29

SCALE:

32 3132

31

3131

KDSKDS

34

70 70A 70 70A

SCALE: SCALE:SCALE:SCALE:

50

72

SCALE:

SCALE: SCALE:

82B

SEE ARCHITECHTURAL

ELEVATIONS FOR DETAILS

SCALE:

15

12

SCALE:

47

43A

7171A

81

82

82A

81

82

83

82A

MILLWORK UPPER SHELVES

SEE ARCH DRAWINGS

MILLWORK UPPER SHELVES

SEE ARCH DRAWINGS

SCALE:

SCALE:

94

97A

110

95

GAS

LINE

19

18

48

83

E1.8

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

GENERAL NOTES

PANEL 'B'

120/208V 3PH 4W

MOUNTING: SURFACE MAINS: 225A

DESCRIPTION EQP TAG LOAD BRKR #

PHASE

# BRKR LOAD EQP TAG DESCRIPTION

A B C

EXIT SIGN/EMERGENCY LTG 460 W 20A 1 ○ 2

20A 3120 W 95 GLASS WASHER

NIGHT LTG W 20A 3 ○ 4

EXTERIOR 24/7 LTG 50 W 20A 5 ○ 6 15A 720 W 97A BAR - OASIS

BACK OF HOUSE LTG 1056 W 20A 7 ○ 8 15A 360 W 110 DRAFT TOWER

BACK OF HOUSE LTG 1264 W 20A 9 ○ 10 15A 912 W 94 BAR - GLASS CHILLER

WASHROOM LTG 336 W 20A 11 ○ 12 20A 120 W BAR - GENERAL RECEP.

DINING LTG - DM1, DM11, DM121290 W 20A 13 ○ 14 15A 1440 W 102 BAR - BACK BAR COOLER

DINING TRACK - DM2, DM3, DM4, DM9598 W 20A 15 ○ 16 15A 200 W BAR - PRINTER

DINING LTG - DM5, DM6, DM13440 W 20A 17 ○ 18 15A 900 W

BAR - T.V.'s (3)

DINING LTG - DM7, DM8, DM10313 W 20A 19 ○ 20 15A 300 W BAR - T.V.

SPARE 20A 21 ○ 22 15A 600 W BAR - GENERAL RECEP.

BAR LTG - DM14, DM15459 W 20A 23 ○ 24 15A 900 W

BAR - T.V.'s (3)

BAR LTG - DM16, DM19, DM20369 W 20A 25 ○ 26 15A 900 W

DINING - T.V.'s (3)

BAR TRACK - DM17 234 W 20A 27 ○ 28 15A 240 W HOSTESS STATION

BAR LTG - DM18 181 W 20A 29 ○ 30 15A 120 W RECEPTION DISPLAY

SPARE 20A 31 ○ 32 15A 720 W DINING - GENERAL RECEP.

PATIO LTG 814 W 20A 33 ○ 34 15A 840 W DINING - GENERAL RECEP.

EXTERIOR LTG 310 W 20A 35 ○ 36 15A 600 W

DINING - T.V.'s (2)

EXTERIOR LTG (ROOF)

60 W 20A 37 ○ 38 15A 250 W ELECTRIC FIREPLACE

SPARE 20A 39 ○ 40 15A SPARE

SIGNAGE 500 W 20A 41 ○ 42 15A SPARE

SIGNAGE 500 W 20A 43 ○ 44 15A 240 W A/V EQUIPMENT

SIGNAGE 500 W 20A 45 ○ 46 15A 240 W A/V EQUIPMENT

SPARE 20A 47 ○ 48 15A 240 W A/V EQUIPMENT

CONTACTORS 120 W 20A 49 ○ 50 15A 600 W PATIO - T.V.'s

CONTACTORS 120 W 20A 51 ○ 52 15A 240 W PATIO - RECEP.


SPARE 15A 55 ○ 56 20A 1800 W W/R HAND DRYER

DOOR BUZZER 120 W 15A 57 ○ 58 20A 1800 W W/R HAND DRYER

BACK OF HOUSE RECEP. 480 W 15A 59 ○ 60 15A SPARE

BACK OF HOUSE RECEP. 480 W 15A 61 ○ 62 15A SPARE

EXTERIOR RECEP. 120 W 15A 63 ○ 64 15A 240 W OFFICE - BACKBOARD

RTU RECEP. 120 W 20A 65 ○ 66 15A 300 W OFFICE - ALARM PANEL

RTU RECEP. 120 W 20A 67 ○ 68 20A 1500 W UPS UNIT

RTU RECEP. 120 W 20A 69 ○ 70 15A 120 W OFFICE - FUTURE SECURITY

MUA RECEP. 450 W 20A 71 ○ 72 15A 120 W OFFICE - PRINTER

GREASE INTERCEPTOR 120 W 20A 73 ○ 74 15A SPARE



79 ○ 80

81 ○ 82

83 ○ 84

TOTAL 11984 W 20682 W TOTAL

TOTAL CONNECTED LOAD 32666 W

DISTRIBUTION PANEL 'A'

120/208V 3PH 4W



PHASE


A B C

ELEC. RM LIGHTING 64 W 15A 1 ○ 2 15A 200 W HYDRO

FIRE ALARM CONTROL PANEL 300 W 15A 3 ○ 4 15A 200 W TELEPHONE

SHUNT TRIP CONTROL 120 W 15A 5 ○ 6 15A SPARE

HWT-1 720 W 15A 7 ○ 8 15A 500 W HOOD CONTROL PANEL

HWT-2 720 W 15A 9 ○ 10 15A 120 W FIRE SUPPRESSION CONTROL

WATER FILTER 120 W 15A 11 ○ 12 15A SPARE

FORCE FLOW HEATER - VESTIBULE 4000 W 30A

13 ○ 14

15A 1000 W BASEBOARD HEATER - ELEC. RM

15 ○ 16

FORCE FLOW HEATER - BAR DOOR 2000 W 15A

17 ○ 18

20A 2500 W BASEBOARD HEATER - H/R OFFICE

19 ○ 20

FORCE FLOW HEATER - MECH RM. 2000 W 15A

21 ○ 22

20A SPARE

23 ○ 24

EF-41 x

1/2 HP 15A 25 ○ 26

20A 3026 W FREEZER CONDENSEREF-5 310 W 15A 27 ○ 28

EF-61 x

1/4 HP 20A 29 ○ 30

FORCE FLOW HEATER - BACK DINING

DOOR

2000 W 15A

31 ○ 32

20A 1747 W COOLER CONDENSER

33 ○ 34

SPARE 15A 35 ○ 36

20A 1747 W BEER COOLER CONDENSER

SPARE 15A 37 ○ 38

39 ○ 40

15A SPARE

41 ○ 42

43 ○ 44 15A SPARE

45 ○ 46 20A SPARE

47 ○ 48 20A SPARE

PREWIRED EXPO LOAD CENTRE 'LC' 35976 W 200A

49 ○ 50

51 ○ 52

53 ○ 54

PANEL 'K' 34290 W 150A

55 ○ 56

200A 32666 W PANEL 'B'57 ○ 58

59 ○ 60



LOAD SUMMARY

CONNECTED

LOAD (W)

DEMAND

LOAD (W)

LIGHTING 8,298 8,298

RECEPTACLES 12,240 8,568

EQUIPMENT 83,338 58,337

MECHANICAL 13,869 9,708

SIGNAGE 1,500 1,500

ELECTRIC HEATING 28,500 28,500

HOT WATER HEATING 1,440

864

AIR CONDITIONER 64,326 45,029

MISCELLANEOUS 5,250 3,150

ESTIMATED FUTURE LOAD

TOTAL 218,761 163,953

LESS HEATING- 28,500

TOTAL DEMAND LOAD 135,453

PANEL 'K'

120/208V 3PH 4W



PHASE


A B C

COFFEE BREWER 81 2704 W 20A

1 ○ 2 15A 960 W 35 REFRIGERATED EQUIPMENT STAND

3 ○ 4 15A 960 W 35 REFRIGERATED EQUIPMENT STAND

DROP IN POP DISPENSER 82 288 W 15A 5 ○ 6 15A 1200 W 42 FRY WARMER

CARBINATOR 82A 600 W 15A 7 ○ 8 15A 384 W 41 UNDERCOUNTER FREEZER

DISHWASHER 50 2760 W 50A 9 ○ 10 15A 240 W 43 DEEP FRYER

POP RACK 82B 600 W 15A 11 ○ 12 15A 240 W 43 DEEP FRYER

ICE CUBER (4#12-21mmC)

12 2704 W 20A

13 ○ 14 15A 456 W 44 SANDWICH UNIT

15 ○ 16 15A 720 W 46 CONVECTION OVEN

FOOD PROCESSOR 19 840 W 15A 17 ○ 18 15A 720 W 46 CONVECTION OVEN

S/S WORK TABLE 15 208 W 15A

19 ○ 20 15A 840 W 113 DRAFT - GLYCOL DECK

21 ○ 22 20A 1680 W 114 DRAFT - CONDENSER

SLICER 18 840 W 15A 23 ○ 24 15A 240 W 3 BEER COOLER DOOR PANEL

OVER COUNTER RECEP. 120 W 20A 25 ○ 26 15A 240 W 3 BEER COOLER EVAP. COIL

FOUR BURNER - OPEN BASE 47 408 W 15A 27 ○ 28 15A GFI 120 W 2/1 DRAIN LINE HEATER

SMOKER (4#8-27mmC)

48 6240 W 40A

29 ○ 30 15A 600 W 2 FREEZER DOOR PANEL

31 ○ 32

20A 1706 W 2 FREEZER EVAP. COIL

PORTABLE FILTER 43A 600 W 15A 33 ○ 34

SPARE 15A 35 ○ 36 15A 240 W 1 COOLER DOOR PANEL

CARBINATOR 82A 600 W 15A 37 ○ 38 15A 240 W 1 COOLER EVAP. COIL

DROP IN POP DISPENSER 82 288 W 15A 39 ○ 40 15A SPARE

COFFEE BREWER 81 2704 W 20A

41 ○ 42 15A SPARE

43 ○ 44 15A SPARE

SPARE 20A

45 ○ 46 20A SPARE

47 ○ 48 20A SPARE

49 ○ 50

51 ○ 52

53 ○ 54

55 ○ 56

57 ○ 58

59 ○ 60



E1.9

Key Plan

General Notes









Architect



LIST, ETC CONTACT:


COORDINATOR


(905) 760-2244 EXT. 2269

KS

IS14-209

14-209


OPERATIONSLIMITED


27th St. W

28th St. W

South Hill

Mall

30th St. W

31th St. W

32th St. W

416-491-4455

[email protected]

TORONTO

604-746-4746

VANCOUVER

403-966-3074

CALGARY


Architect

Documents

E0 · 2014. 10. 17. · 15a 120v 1ph isolated ground duplex receptacle, hubbell no.ig-5252 provide separate neutral and ground wire for each outlet. 15a 120v 1ph gfci grounded duplex