Embed Size (px)
Citation preview
1/” TM
SSmarttandard
Email: [email protected]
Cabinet Barn Door Hardware Manual
Measurements
(1 Door SuperMini I-Shape 4.0ft)
4.1,
4.2,
4.3, 2 x Rubber End
2 x Door Stopper
1 x Hex Key
4.4, 1 x U-Shape Floor Guide
3.1,
3.2, 3 x Lag Bolt
3 x Wall Spacer
A
B
C
E
D
FG
3/”
16”
48”
16”
H+1/” H
/”
Product Content
1.1, 1 x Rail
Tools Needed
1,
2,
Pencil
Phillips Screwdriver
Drill
Wrench3,
4, Level
5,
Tape6,
Overall Rail length is 48”.
The gap between each pre-drilled hole is 16”.
Distance from door top side to holes on the cabinet is 1/”.Distance from the bottom of the door to the top of cabinet base is ⁄”.Door height is H.
You will need a minimum of 3/" from the top of your door to the ceiling of cabinet for this kit to fit correctly.
A
B
C
E
D
F
G The height of holes on the cabiner is H+1/”to the top of cabinet base
1/”
2.1, 2 x Hanger
4 x Long Door Bolt2.3,
4 x Short Door Bolt2.2,
TM TM TM TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
B
A
A
B
1 2
3 4
A
B
B
B
A
A
B
A Install the rail and spacers to cabinet using lag bolts.Level can make the rail horizontal.
B
A
Place the rail against the cabinet, and use a pencil to mark where the holes should be.Make sure height of holes on the wall of cabinet is Door Height+1/” to the top of base.
If you want to mount floor guide on the wall of cabinet, use lag bolts and anchor to fasten floor guide on the wall of cabinet. Adjust two short bolts to find optimum location to let the door fit in between the floor guide.
If you want to mount floor guide on the base of cabinet or floor, use lag bolts and anchor to fasten floor guide on the base of cabinet or floor directly without using two short bolts.
Foor guide is used to keep your door stable and prevent the door bottom swinging back and forth when you slide it open and closed.
The rubber ends are used to protect the door from touching the rail when sliding the door. You need to drill holes on the door top side, please drill the holes /” away from the edge of the door. Then install the rubber ends on the door.
Install the hangers onto the door according to the measurements in the pictures above.
Insert door stoppers into rail. Door stopper is used to prevent the hangers coming out of the rail. Adjust the door stoppers to find a suitable position, Use the hex key to screw the door stoppers in place.After hang the door over the rail, turn the rubber ends approximately 180 degrees so that they are stuck between the door and the rail.
B
1/”
/”
2”
A
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
TM
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
SSmart
tandard
