Dynojet Power Vision Short Manual

Power Vision Getting Started Guide - 12191 Mendenhall Drive North Las Vegas, NV 89081

1-800-992-4993 www.dynojetpowervision.com

Power VisionGETTING STARTED GUIDE

Parts List

1 Power Vision Unit

1 J1850 Cable

1 USB Cable

1 Software CD

1 Getting Started Guide

!!!---WARNING---!!!FOR RACING VEHICLE USE ONLY

Note: This product is not for use on roads or vehicles subject to emission control requirements and is not legal for use or installation on motor vehicles operated on public highways in the State of California or other States where similar emission and decibel regulation laws may apply. The user shall determine suitability of the product for his or her use. The user shall assume all risk and liability in violation of

regulations and any incurred fi nancial obligations due to vehicle inspections or emissions tests.

Power Vision Getting Started Guide - 298100014.02 www.dynojetpowervision.com

Determining Your Operating System

Windows XP

1 Right-click My Computer and select Properties.

2 Click the General tab.

For a 32-bit version operating system, Windows XP Professional Version <Year> appears under System.Use PowerVisionSoftwareInstaller_x32_xxxxx.msi for this installation.

For a 64-bit version operating system, Windows XP Professional x64 Version <Year> appears under system.Use PowerVisionSoftwareInstaller_x64_xxxxx.msi for this installation.

Windows Vista


2 Verify System Type.

Windows 7


2 Verify System Type.

FIG

. 1F

IG. 2

FIG

. 3


WinPV Software Installation

Use the following instructions to install the WinPV software on your computer.

It is strongly recommended that you exit all other Windows programs before running this install program.

1 Insert the WinPV CD in your CD-ROM drive.

2 Double-click My Computer and browse to your CD/DVD Drive.

3 Double-click PowerVisionSoftwareInstaller_x32_xxxxx.msi for 32-bit operating systems or PowerVisionSoftwareInstaller_x64_xxxxx.msi for 64-bit operating systems.

Or

Download the WinPV software from Dynojet.

4 Read the Welcome window and click Next to continue.

5 Carefully read the WinPV license agreement, check the accept box, and click Next to continue.

To install WinPV, you must accept this agreement. If you do not, Setup will close.

6 Carefully read the information provided in the Readme window and click Next to continue.

7 Select a destination location for your WinPV software to be installed and click Next to continue.

Dynojet recommends that you do not change the default destination folder.

8 Setup will automatically add program icons to the Start menu. You may type a new folder name or select one from the Existing Folders list. Click Next to continue.

9 Read the summary of your settings and click Install.

10 Click Finish to complete the installation.

11 Continue with the Power Vision Driver Installation.

FIG

. 4F

IG. 5

FIG

. 6


Power Vision Driver Installation

1 Using the USB cable, connect the Dynojet Power Vision to your computer.

The Found New Hardware window will open.

2 Select Yes, this time only and click Next.

3 Select Install from a list or specific location and click Next.

4 Select Search for the best driver in these locations.

5 Verify the location points to your Power Vision folder in Program Files.

6 Click Next.

7 Click Finish to close the wizard.

8 Continue with Checking the WinPV Update Client.

FIG

. 7F

IG. 8

FIG

. 9


Checking the WinPV Update Client

1 Using the USB cable, connect the Dynojet Power Vision to your computer.

2 Click Start on the Windows task bar and click All Programs.

3 Select PowerVision >PV Update Client.

4 Click Check For Updates. Select the following items to update:

PV Firmware

PV Tune Database

PV Software (Update Utility, WinPV, etc.)Note: Make sure you select the correct operating version. Refer to Determining

Your Operating System on page 2.

5 Click Download & Install Selected Updates.

6 As the downloads are completed, click OK.

The Welcome to the Power Vision Software Setup Wizard window will appear.

7 Click Next to continue.

8 Carefully read the Power Vision software license agreement, check the accept box, and click Next to continue.

To install the Power Vision software, you must accept this agreement. If you do not, Setup will close.

The Power Vision Software Feature window will appear.

9 Click Next to continue. Dynojet recommends you do not make any changes to this window.

Setup is ready to install the Power Vision Software.

10 Click Install to begin installation.

11 The Power Vision Software update is now complete. Click Finish to exit the Setup Wizard.

For detailed software instructions and user information, refer to the Help included in the software.

FIG

. 10

FIG

. 11

FIG

. 12

Power Vision Getting Started Guide - 698100014.02 Toll Free: 1-800-992-4993

Installing the Power Vision

1 Connect the Power Vision to the ECU’s J1850 port.

2 Route the Power Vision cable away from any moving or hot parts.

Dynojet recommends using zip ties to secure the cable to existing non-moving components.

3 The Power Vision module may be mounted to the bike’s handlebars using Techmount hardware.

Note: The Power Vision does not need to remain on the bike.

Figure 15 and Figure 16 are examples of the Power Vision module mounted to a 2009 Night Rod using the Techmount bracket.

FIG

. 13

FIG

. 14

FIG

. 15


FIG

. 16

FIG

. 18

Saving Stock Calibration

Save Stock saves a copy of the stock calibration to the Power Vision module as a backup. Save Stock must be completed before any editing can be done to the parameters on the device or in the WinPV software.

Use the following steps to save the stock ECU calibration to the Power Vision module.

1 Touch Vehicle Tools >Save Stock.

Figure 15 and Figure 16 are examples of the Power Vision module mounted to a 2009 Night Rod using the Techmount bracket.

2 Touch Yes.

3 Touch OK when completed.

FIG

. 17


Loading a Stock File for Editing

The Power Vision accepts custom tune files created in WinPV and pre-loaded Dynojet maps installed in the Power Vision memory from Dynojet Research. To edit stock files, the Power Vision must be married to the ECU. Marrying the Power Vision to the ECU locks the Power Vision module to that ECU and prevents a single device from being used on multiple ECUs. You cannot unlock a Power Vision from a married ECU. Once the marriage process is complete, you can open the stored calibration in the WinPV software to edit all parameters or change Dynojet specific functions on the device.

Use the following steps to load a copy of the stock tune file for editing.

Note: Once this process is complete, the Power Vision module will be married to the ECU.

FIG

. 19

1 Touch Program Vehicle >Load Tune.

2 Touch Load Copy of Stock.

This will load a copy of the stock tune into the Tune Manager. Once loaded into a slot, it will be converted into a custom tune which can be edited and/or flashed to the ECU.

3 Touch OK.

5 Touch a slot to save the selected tune file.

Note: If there is any data in the selected slot, it will be overwritten.

6 Touch OK.

A copy of the stock tune will be saved.

7 Touch OK.

FIG

. 20

FIG

. 22

The Power Vision and the bike are now married.

4 Touch OK.

The tune is now ready.

8 Touch Flash to flash this tune to the ECU.

or

Touch Edit to edit this tune.

or

Touch Exit to exit the screen without any changes.

FIG

. 21

FIG

. 23


F

IG. 2

4Loading a Custom or Dynojet Tune File

The Power Vision accepts custom tune files created in WinPV and pre-loaded Dynojet maps installed in the Power Vision memory from Dynojet Research.

Use the following steps to load a Dynojet map file to the ECU.

1 Touch Program Vehicle >Load Tune.

2 Select Dynojet Tune.

The Power Vision is now searching for compatible tunes for the connected ECU.

3 Touch OK.

7 Touch a slot to save the selected tune file.

Note: If there is any data in the selected slot, it will be overwritten.

8 Touch OK.

A copy of the stock tune will be saved.

FIG

. 25

FIG

. 28

4 Select a Dynojet Tune file to load.

5 Touch Select.

The tune is now ready.

9 Touch Flash to flash this tune to the ECU.

or

Touch Edit to edit this tune.

or

Touch Exit to exit the screen without any changes.

FIG

. 26

FIG

. 29

6 Verify the Tune information. If the Tune information is correct, touch Continue.

FIG

. 27

10 Touch OK.

11 Turn the ignition key off and wait ten seconds.

12 Turn the ignition key back on.

FIG

. 30


Outline Key

Main Buttons

Action of User or Power Vision

Text that will be displayed on screen

PV or User determines somthing

LOAD TUNE

DYNOJET CUSTOM STOCK

Displays a list of available DYNOJET TUNES

List of any LOADED TUNESBasically the Tune Manager

User selects any of the tunes that have been either preloaded, loaded through

DYNOJET TUNES or STOCK TUNES

Select the type of tune to load into tune manager.

This will LOAD a copy of the STOCK tune into the TUNE MANAGER. Once Loaded into a SLOT it will be

converted into a CUSTOM tune which can be EDITED and or FLASHED to ECMNo DYNOJET TUNES are

available for this bike

No Tunes have been loaded into the Tune Manager,

Please LOAD Either a DYN-OJET TUNES or a STOCK

TUNEReturns to LOAD TUNE

Checks to see if Cus-tom Tune is Editable

Returns to LOAD TUNE

Returns to Tuning menu

Select the Slot you would like to Load the selected tune into

Description of Selected Tune

User Selects Slot

User Selects Dynojet Tune

Select Parameter to Edit

Select Parameter to EditThis tune is locked and not editable

Select Slot to save to SAVE a COPY of STOCK to:

User selects slot

The COPY of STOCK has been successfully save.

User Selects Parameter

User Selects Parameter

User EDITS Parameter

User EDITS Parameter

User CONFIRMS EDIT

User CONFIRMS EDIT

User saves EDIT to tune

User saves EDIT to tune

Would you like to save this EDIT to the tune?

Would you like to save this EDIT to the tune?

(Parameter edit no change from current)

(Parameter edit no change from current)

Confirm

Confirm

Returns to EDIT or APPLY

Returns to EDIT or APPLY

Loads tune into chosen slot in Tune Manager

Would you now like to EDIT or Flash this tune to the ECU?

Would you now like to EDIT or Flash this tune to the ECU?

CAUTION!!!Any Data in this slot will be over-

written by the selected tune.

Flashes tune to ECU

Flashes tune to ECU

Turn off bike to set.

Turn off bike to set.

IF Yes

Slot 1 Slot 1Slot 3 Slot 3Slot 5 Slot 5Slot 2 Slot 2Slot 4 Slot 4Slot 6 Slot 6Cancel

Cancel

Cancel

Cancel

Cancel

Cancel

Cancel

Cancel

NO

NO

NO

NO

Select

Continue

Select

OK

OK

OK

Select

OK

OK

OK

YES

YES

IF Yes

EDIT

EDIT

SELECT

YES

YES

IF None IF None

FLASH

FLASH

EXIT

EXIT

CANCEL

Cancel

IF NOT

Documents

Dynojet Power Vision Short Manual