DynaFlex Thermplastic Hose Catalog - Flex Inc - Adapters Inc

DYNA FLEX Thermoplastic Hose Catalog

TABLE OF CONTENTS DESCRIPTION PAGE Thermoplastic Hose Specifications SAE100R7 4 (single line, non-conductive, twinline) SAE100R8 8 (single line, non-conductive, twinline) Sewer Jetting 12 Paint Spray 14

Couplings Crimp Ferrules 18 NPTF Male Pipe 19 JIC 37 Degree Solid Male 20 JIC 37Degree Swivel Female, JIC 37Degree Swivel Female 90 21 JIC 37Degree Swivel Female 45 22 BSPP Male Parallel 23 BSPT Male Parallel 24 BSPP Swivel Female 25 BSPP Swivel Female 45 & 90 Degree 26 Metric Stud Male Light, Metric Female Swivel Light 27 Metric Female Swivel Light 45 & 90 Degree 28 Metric Stud Male Heavy, Metric Female Swivel Heavy 29 Metric Female Swivel Heavy 45 & 90 Degree 30 JIS Komatsu Female & JIS Komatsu BSP Female 31 ORFS Female & Male O-Ring Boss 32 ORFS Female 45 and 90 degree swivel 33 Male O-ring Boss Swivel 90 & NPSM Swivel Female 34 Blank Insert & Hose Mender 35 Banjo BSP & Banjo Metric 36 Metric Standpipe 37 Metric Standpipe 90 38 Metric Standpipe 45 39

Page 2

Hose Mender 40 Karcher Fitting 41

Crimper D105QK Hydraulic Hose Crimper 42 Print Catalog Request Form 43

Page 3

DYNA FLEX SAE 100R7

711 (BLACK)

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R7 requirements. For pneumatic systems use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile synthetic fiber Cover: Black high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.

Maximum Oper. Press.

Minimum Burst Press.

Hose Part No.

In. mm. In. mm. PSI BAR PSI BAR

Min. Bend Radius(In.)

Wgt. Per 100 Ft. (Lbs.)

701-02* 1/8 3.18 .305 7.75 3,000 207 12,000 827 1/2 2.5 711-03 3/16 4.76 .405 10.29 3,250 224 13,000 896 3/4 5.5 711-04 1/4 6.35 .505 12.83 3,000 207 12,000 827 1-1/4 7.0 711-05 5/16 7.94 .585 14.86 2,500 172 10,000 689 1-3/4 10.0 711-06 3/8 9.53 .645 16.38 2,250 155 9,000 620 2 10.5 711-08 1/2 12.70 .810 20.57 2,000 138 8,000 552 3 15.0 711-12 3/4 19.05 1.11 28.19 1,250 86 5,000 345 9-1/2 29.0 711-16 1 25.40 1.42 36.07 1,000 69 4,000 276 12 40.0 * 1/8” I.D. does not apply to SAE100R7

DYNA FLEX, INC. 7300 INDUSTRIAL PARK BLVD.

MENTOR, OHIO 44060 U.S.A.

PHONE: (440) 946-0719 TOLL FREE: (800) 525-8463 FAX: (440) 946-4620 Web Site: www.dynaflexinc.com E-Mail: [email protected]

Page 4

DYNA FLEX SAE 100R7

7110 (ORANGE) NON-CONDUCTIVE

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R7 requirements. For pneumatic systems, use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile synthetic fiber Cover: Orange non-conductive high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.




7010-02* 1/8 3.18 .305 7.75 3,000 207 12,000 827 1/2 2.5 7110-03 3/16 4.76 .405 10.29 3,250 224 13,000 896 3/4 5.5 7110-04 1/4 6.35 .505 12.83 3,000 207 12,000 827 1-1/4 7.0 7110-05 5/16 7.94 .585 14.86 2,500 172 10,000 689 1-3/4 10.0 7110-06 3/8 9.53 .645 16.38 2,250 155 9,000 620 2 10.5 7110-08 1/2 12.70 .810 20.57 2,000 138 8,000 552 3 15.0 7110-12 3/4 19.05 1.11 28.19 1,250 86 5,000 345 9-1/2 29.0 7110-16 1 25.40 1.42 36.07 1,000 69 4,000 276 12 40.0 * 1/8” I.D. does not apply to SAE100R7




Page 5

DYNA FLEX SAE 100R7 TWIN-LINE

711T (BLACK) TWIN-LINE

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R7 requirements. For pneumatic systems, use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile synthetic fiber Cover: Black high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.




711-03T 3/16 4.76 .400 10.16 3,250 224 13,000 896 3/4 11 711-04T 1/4 6.35 .505 12.83 3,000 207 12,000 827 1-1/4 14 711-06T 3/8 9.53 .645 16.38 2,250 155 9,000 620 2 21 711-08T 1/2 12.70 .810 20.57 2,000 138 8,000 552 3 30

DYNA FLEX, INC.

7300 INDUSTRIAL PARK BLVD. MENTOR, OHIO 44060 U.S.A.


Page 6


8110T (ORANGE) NONCONDUCTIVE TWIN-LINE

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R8 requirements. For pneumatic systems use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile aramid fiber Cover: Orange high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.


Min. Bend Radius (In.)


8110-03T 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 8110-04T 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 8110-06T 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 8110-08T 1/2 12.70 .810 20.57 3,500 241 14,000 965 3 15.0




Page 7

DYNA FLEX SAE 100R8

811 (BLACK)

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R8 requirements. For pneumatic systems use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile aramid fiber Cover: Black high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.




811-03 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 811-04 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 811-06 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 811-08 1/2 12.70 .810 20.57 3,500 241 14,000 965 3 15.0




Page 8


8110T (ORANGE) NONCONDUCTIVE TWIN-LINE


Nominal I.D.

Nominal O.D.



Hose Part No.




8110-03T 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 8110-04T 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 8110-06T 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 8110-08T 1/2 12.70 .810 20.57 3,500 241 14,000 965 3 15.0




Page 9

DYNA FLEX SAE 100R8

8110 (ORANGE) NONCONDUCTIVE


Nominal I.D.

Nominal O.D.



Hose Part No.




8110-03 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 8110-04 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 8110-06 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 8110-08 1/2 12.70 .810 20.57 3,500 241 14,000 965 3 15.0




Page 10


811T (BLACK) TWIN-LINE

Recommended For: Medium pressure hydraulic and pneumatic systems. Meets or exceeds SAE 100R8 requirements. For pneumatic systems use perforated (pin-pricked) hose. Innercore: Synthetic oil resistant polyester tube Reinforcement: Braided high tensile aramid fiber Cover: Black high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F. (-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.




811-03T 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 811-04T 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 811-06T 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 811-08T 1/2 12.70 .810 20.57 3,500 241 14,000 965 3 15.0




Page 11

DYNA FLEX SEWER JETTING

SWRB (BLACK)

Recommended For: Use on high pressure sewer cleaning and jetting equipment. Innercore: Seamless polyester elastomer tube

Reinforcement: Braided high tensile aramid fiber Cover: Black high abrasion resistant polyurethane Temperature Range: -40 degrees F. to +122 degrees F. (-40 degrees C. to +50 degrees C.)

Nominal I.D.

Nominal O.D.



Hose Part No.




SWRB-03 3/16 4.76 .390 9.91 5,000 345 20,000 1397 3/4 5.5 SWRB-04 1/4 6.35 .480 12.19 5,000 345 20,000 1379 1-1/4 7.0 SWRB-06 3/8 9.53 .645 16.38 4,000 276 16,000 1103 2 10.5 SWRB-08 1/2 12.70 .810 20.57 4,000 241 14,000 965 3 15.0




Page 12

DYNA FLEX INC. Sewer Cleaning Hose SWRO

Recommended For: Use on high pressure sewer cleaning and jetting equipment. Innercore: Orange, seamless elastomer tube

Reinforcement: Braided high tensile synthetic fiber Cover: Orange high abrasion resistant polyurethane Temperature Range: -40 degrees F. to +122 degrees F. (-40 degrees C. to +50 degrees C.)

Hose Part No.

Nominal I.D.

Nominal O.D.






SWRO-16 1 25.40 1.44 36.58 2,500 172 6,250 431 6 40.0




Page 13

DYNA FLEX PAINT SPRAY

7100 (NU-BLU) ®

Recommended For: Use in Airless/Wireless paint spray applications Innercore: Nylon (Flexible) Reinforcement: Braided high tensile conductive synthetic fiber Cover: Blue high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F.

(-54 degrees C. to +100 degrees C.)

Nominal I.D.

Nominal O.D.


Hose Part No.

In. mm. In. mm. PSI BAR


Wgt. Per 100 Ft.(Lbs.)

7100-03 3/16 4.76 .405 10.29 3,300 227 3/4 5.5 7100-04 1/4 6.35 .505 12.83 3,300 227 1-1/4 7.0 7100-06 3/8 9.53 .645 16.38 3,300 227 2 10.5 7100-08 1/2 12.70 .810 20.57 2,000 138 3 15.0

NOTE: Paint spray hose is furnished only as a completed assembly.

Hose will be coiled and cut to length specified by customer. All hose assemblies come complete with hose ends, spring

guards and “Warning Tags”.

NOT TO BE USED WITH PUMPS OR EQUIPMENT THAT EXCEED THE MAXIMUM OPERATING PRESSURE.


Page 14


7102 (HI NU-BLUE TWO) ®

Recommended For: Use in Airless/Wireless paint spray applications Innercore: Nylon (Flexible) Reinforcement: Two braids high tensile conductive synthetic fiber Cover: Blue high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F.


Nominal I.D.

Nominal O.D.


Hose Part No.



Wgt. Per 100 Ft.(Lbs.)

7102-03 3/16 4.76 .405 10.29 3,300 227 3/4 5.5 7102-04 1/4 6.35 .505 12.83 3,300 227 1-1/4 7.0 7102-06 3/8 9.53 .645 16.38 3,300 227 2 10.5 7102-08 1/2 12.70 .810 20.57 2,000 138 3 15.0



guards and “Warning Tags”.

NOT TO BE USED WITH PUMPS OR EQUIPMENT THAT EXCEED THE MAXIMUM OPERATING PRESSURE.


Page 15


8100 (SUPR-NU SPRAY) ®

Recommended For: Use in Airless/Wireless paint spray applications. Lighter than comparable wire reinforced paint spray hoses. Innercore: Nylon (Flexible) Reinforcement: Braided high tensile conductive aramid fiber Cover: Red high abrasion resistant polyurethane Temperature Range: -65 degrees F. to +212 degrees F.


Nominal I.D.

Nominal O.D.


Hose Part No.




8100-03 3/16 4.76 .390 9.19 6,000 413 3/4 5.5 8100-04 1/4 6.35 .480 12.19 6,000 413 1-1/4 7.0 8100-06 3/8 9.53 .645 16.38 5,000 345 2 10.5 8100-08 1/2 12.70 .810 20.57 3,500 241 3 15.0



guards and “Warning Tags”. NOT TO BE USED WITH PUMPS OR EQUIPMENT THAT EXCEED THE MAXIMUM OPERATING PRESSURE.




Page 16

DYNA FLEX Thermoplastic Hose and Fittings

Air and Pneumatic Applications:

All hose assemblies should be perforated (pin-pricked) before being used in an air or gaseous application. This permits any gas that has migrated through the inner core to escape through the cover and into the atmosphere without causing damage to the hose. Please notify our sales staff if this is a requirement for your particular hose application.

Hose Conductivity & Non-Conductivity:

Exercise caution when routing hydraulic hose by an electrical source. If you are close to an electrical source we highly recommend using Dyna Flex Inc. orange non-conductive hose.

Special Requirements:

Hoses can be designed and constructed to meet your specific engineering needs. Please consult our sales staff for details

Page 17


SAE100R7 AND SAE100R8 FERRULES




PART NO.

HOSE

I.D.

"A" "B" "C"

IN

MM

IN

MM

IN

MM

IN

MM803 3/16 4.8 .551 14.0 1.063 27.0 .417 10.6804 1/4 6.4 .669 17.0 1.142 29.0 .531 13.5805 5/16 7.9 .748 19.0 1.181 30.0 .598 15.2806 3/8 9.5 .826 21.0 1.220 31.0 .661 16.8808 1/2 12.7 1.00 25.4 1.338 34.0 .819 20.8810 5/8 15.9 1.12 28.5 1.417 36.0 .945 24.0812 3/4 19 1.26 32.0 1.417 36.0 1.094 27.8816 1 25.4 1.57 40.0 1.969 50.0 1.358 34.5

Page 18


MALE PIPE




PART NO. HOSEI.D.

DASH SIZE

THREAD HEX IN.

"H"

CUTOFFIN. "C"

2203-102 3/16 03 1/8-27 31/64 .8662204-104 1/4 04 1/4-18 19/32 1.0622204-102 1/4 04 1/8-27 31/64 .8662204-104 1/4 04 1/4-18 19/32 1.1022205-104 5/16 05 1/4-18 3/4 1.1022205-106 5/16 05 3/8-18 19/32 1.1022206-104 3/8 06 1/4-18 3/4 1.1022206-106 3/8 06 3/8-18 19/32 1.1022208-106 1/2 08 3/8-18 3/4 1.1022208-108 1/2 08 1/2-14 27/32 1.3782210-112 5/8 10 3/4-14 1-1/16 1.4172212-112 3/4 12 3/4-14 1-1/16 1.4562212-116 3/4 12 1-11-1/2 1-13/32 1.6932216-116 3/4 12 1-11-1/2 1-13/32 1.7322216-120 1 16 1-1/4-11-1/2 1-13/16 1.8102220-120 1-1/4 20 1-1/4-11-1/2 1-13/16 1.8502224-124 1-1/2 24 1-1/2-11-1/2 1-31/32 1.9292232-132 1 32 2-11-1/2 2-9/16 2.165

Page 19


MALE JIC

PART NO. HOSEI.D.

DASH SIZE

THREAD HEX IN.

"H"

CUTOFF IN. "C"

2203-504 3/16 03 7/16-20 31/64 1.0232204-504 1/4 04 7/16-20 31/64 1.0622204-505 1/4 04 1/2-20 9/16 1.0622204-506 1/4 04 9/16-18 19/32 1.0622205-506 5/16 05 9/16-18 19/32 1.0622206-506 3/8 06 9/16-18 19/32 1.062

2206-507SAE 3/8 06 5/8-18 11/16 1.0622206-508 3/8 06 3/4-16 3/4 1.1812206-510 3/8 06 7/8-14 15/16 1.3382208-508 1/2 08 3/4-16 3/4 1.2202208-510 1/2 08 7/8-14 15/16 1.3782208-512 1/2 08 1-1/16-12 1-1/16 1.4562210-510 5/8 10 7/8-14 15/16 1.3782210-512 5/8 10 1-1/16-12 1-1/16 1.4562212-510 3/4 12 7/8-14 15/16 1.4172212-512 3/4 12 1-1/16-12 1-1/16 1.4962212-514 3/4 12 1-3/16-12 1-1/4 1.6142212-516 3/4 12 1-5/16-12 1-11/32 1.6542216-512 1 16 1-1/16-12 1-1/16 1.5352216-516 1 16 1-5/16-12 1-11/32 1.693




Page 20

DYNA FLEX Thermoplastic Hose and Fittings FEMALE JIC SWIVEL

PART NO. HOSEI.D. IN.

DASH

SIZE

THREAD HEX IN.

"H"

CUTOFFIN. "C"

2202-6031PC* 1/8 02 3/8-24 9/16 .90 2203-604 3/16 03 7/16-20 19/32 .5122204-604 1/4 04 7/16-20 9/16 .5512204-605 1/4 04 1/2-20 11/16 .5902204-606 1/4 04 9/16-18 11/16 .6302205-606 5/16 05 9/16-18 11/16 .5902206-606 3/8 06 9/16-18 3/4 .6302206-607

SAE3/8 06 5/8-18 3/4 .590

2206-608 3/8 06 3/4-16 15/16 .6692208-608 1/2 08 3/4-16 7/8 .7092208-610 1/2 08 7/8-14 1 .7482208-612 1/2 08 1-1/16-12 1-1/4 .7482210-610 5/8 10 7/8-14 1-1/16-12 .7482210-612 5/8 10 1-1/16-12 1-1/4 .7482212-612 3/4 12 1-1/16-12 1-1/4 .7872212-614 3/4 12 1-3/16-12 1-13/32 .8272212-616 3/4 12 1-5/16-12 1-1/2 .8272216-616 1 16 1-5/16-12 1-1/2 .866

FEMALE JIC SWIVEL 90 ELBOW


DASH

SIZE

THREAD HEX IN.

"H"

DROPIN. "X"

CUTOFFIN. "C"

2203-60490M 3/16 03 7/16-20 19/32 .846 .8662204-60490M 1/4 04 7/16-20 19/32 .984 .9842204-60590M 1/4 04 1/2-20 11/16 .984 .9842204-60690M 1/4 04 9/16-18 3/4 1.063 .9842205-60690M 5/16 05 9/16-18 3/4 1.26 .9842206-60690M 3/8 06 9/16-18 3/4 1.22 1.2992206-60790M

SAE 3/8 06 5/8-18 7/8 1.26 1.299

2206-60890M 3/8 06 3/4-16 15/16 1.338 1.2992208-60890M 1/2 08 3/4-16 15/16 1.535 1.5352208-61090M 1/2 08 7/8-14 1-1/16 1.575 1.5352208-61290M 1/2 08 1-1/16-12 1-1/4 1.654 1.5352210-61090M 5/8 10 7/8-14 1-1/16 1.771 1.7712210-61290M 5/8 10 1-1/16-12 1-1/4 1.771 1.7712212-61290M 3/4 12 1-1/16-12 1-1/4 2.125 2.2042212-61490M 3/4 12 1-3/16-12 1-13/32 2.086 2.2042212-61690M 3/4 12 1-5/16-12 1-1/2 2.204 2.2042216-61690M 1 16 1-5/16-12 1-1/2 2.599 2.756

*1 piece fitting includes ferrule Page 21


FEMALE JIC SWIVEL 45 DEGREE ELBOW


DASH SIZE

THREAD HEX IN.

"H"

DROPIN

"X"

CUTOFFIN. "C"

2203-60445M 3/16 03 7/16-20 9/16 .551 1-1/42204-60445M 1/4 04 7/16-20 9/16 .551 1-9/162204-60545M 1/4 04 1/2-20 11/16 .551 1-9/162204-60645M 1/4 04 9/16-18 3/4 .590 1-5/82205-60645M 5/16 05 9/16-18 3/4 .787 1-15/162206-60645M 3/8 06 9/16-18 3/4 .670 1-31/322206-60745M

SAE3/8 06 5/8-18 29/32 .670 2

2206-60845M 3/8 06 3/4-16 15/16 .750 2-1/162208-60845M 1/2 08 3/4-16 15/16 .867 2-1/22208-61045M 1/2 08 7/8-14 1-1/16 .906 2-9/162208-61245M 1/2 08 1-1/16-12 1-1/4 .945 2-5/82210-61045M 5/8 10 7/8-14 1-1/16 .906 2-11/162210-61245M 5/8 10 1-1/16-12 1-1/4 .945 2-21/322212-61245M 3/4 12 1-1/16-12 1-1/4 1.102 3-5/162212-61445M 3/4 12 1-3/16-12 1-7/16 1.102 3-5/162212-61645M 3/4 12 1-5/16-12 1-1/2 1.182 3-3/82216-61645M 1 16 1-5//16-12 1-1/2 1.339 4-1/8




Page 22


BSP MALE FITTING

DYNA FLEX PART NO.

HOSE I.D. IN.

DASH SIZE

THREAD HEX MM "H"

CUTOFFIN. "C"

3020302 3/16 03 1/8-28 12 .8273020304 3/16 03 1/4-19 15 1.0233020402 1/4 04 1/8-28 12 .8273020404 1/4 04 1/4-19 15 1.0633020406 1/4 04 3/8-19 19 1.1023020504 5/16 05 1/4-19 15 1.0633020506 5/16 05 3/8-19 19 1.1023020604 3/8 06 1/4-19 15 1.0633020606 3/8 06 3/8-19 19 1.1423020608 3/8 08 1/2-14 22 1.2603020806 1/2 08 3/8-19 19 1.1423020808 1/2 08 1/2-14 22 1.2993020810 1/2 08 5/8-14 19 1.3383020812 1/2 08 3/4-14 22 1.3783021008 5/8 10 5/8-14 27 1.2993021010 5/8 10 5/8-14 22 1.3783021012 5/8 10 3/4-14 27 1.3783021212 3/4 12 3/4-14 27 1.4173021212 3/4 12 1-11 36 1.5353021616 1 16 1-11 36 1.574




Page 23


BSPT MALE FITTING

DYNA FLEX PART NO.

HOSE I.D. IN.

DASH SIZE

THREAD HEX MM "H"

CUTOFFIN. "C"

3020302T 3/16 03 1/8-28 12 .8273020304T 3/16 03 1/4-19 15 1.0633020402T 1/4 04 1/8-28 12 .8663020404T 1/4 04 1/4-19 15 1.1033020406T 1/4 04 3/8-19 19 1.1033020504T 5/16 05 1/4-19 15 1.1033020506T 5/16 05 3/8-19 19 1.1033020604T 3/8 06 1/4-19 15 1.1033020606T 3/8 06 3/8-19 19 1.1033020608T 3/8 08 1/2-14 22 1.2993020806T 1/2 08 3/8-19 19 1.1423020808T 1/2 08 1/2-14 22 1.3383021008T 5/8 10 1/2-14 22 1.3383020812T 1/2 08 3/4-14 27 1.4173021008T 5/8 10 5/8-14 22 1.3383021010T 5/8 10 5/8-14 24 1.3783021012T 5/8 10 3/4-14 27 1.4173021212T 3/4 12 3/4-14 27 1.4563021216T 3/4 12 1-11 36 1.4563021616T 1 16 1-11 36 1.732




Page 24


BSP FEMALE SWIVEL 60 DEG. CONE


DASH SIZE

HOLE THREAD

"T"

HEXMM"E"

CUTOFF

IN. "C"

3010302 3/16 03 1/8-28 14 .5903010304 3/16 03 1/4-19 19 .6693010402 1/4 04 1/8-28 14 .6303010404 1/4 04 1/4-19 19 .6693010406 1/4 04 3/8-19 22 .7483010504 5/16 05 1/4-19 19 .7093010506 5/16 05 3/8-19 22 .7483010604 3/8 06 1/4-19 19 .7093010606 3/8 06 3/8-19 22 .7483010608 3/8 08 1/2-14 27 .8663010806 1/2 08 3/8-19 22 .7873010808 1/2 08 1/2-14 27 .9053010810 1/2 08 5/8-14 30 .8663010812 1/2 08 3/4-14 32 .8663011010 5/8 10 5/8-14 30 .8663011212 5/8 10 3/4-14 32 .8663011212 3/4 12 3/4-14 45 .9053011216 3/4 12 1-11 58 .9843011616 1 16 1-11 58 1.023




Page 25

DYNA FLEX Thermoplastic Hose and Fittings BSP SWIVEL FEMALE PARALLEL PIPE

45 DEGREE 60 DEGREE CONE

DYNA FLEX

PART NO. HOSE

I.D. IN.

DASH SIZE

THREAD HEXMM."H"

CUTOFF IN. "C"

DROP IN. "X"

3040302 3/16 03 1/8-28 14 1.338 1-3/8 3040304 3/16 03 1/4-19 19 1.338 1-3/8 3040404 1/4 04 1/4-19 19 1.614 1-5/8 3040406 1/4 04 3/8-19 22 1.730 1-3/4 3040506 5/16 05 3/8—19 22 1.968 2 3040606 3/8 06 3/8-19 22 2.047 2-1/32 3040608 3/8 06 1/2-14 27 2.165 2-3/16 3040808 1/2 08 1/2-14 27 2.637 2-5/8 3040810 1/2 08 5/8-14 30 2.677 2-21/32 3040812 1/2 08 3/4-14 32 2.677 2-21/32 3041010 5/8 10 5/8-14 30 2.677 2-23/32 3041012 5/8 10 3/4-14 32 2.835 2-13/16 3041212 3/4 12 3/4-14 32 3.307 3-5/16 3041216 3/4 12 1-11 38 3.425 3-7/16 3041616 1 16 1-11 38 4.173 4-3/16

BSP SWIVEL FEMALE PARALLEL PIPE 90 DEGREE 60 DEGREE CONE

PART NO.

HOSEI.D. IN.

DASH SIZE

THREAD HEXMM."H"

CUTOFF IN. "C"

DROP IN. "X"

3030302 3/16 03 1/8-28 14 1.338 7/83030304 3/16 03 1/4-19 19 1.338 13030404 1/4 04 1/4-19 19 1.614 13030406 1/4 04 3/8-19 22 1.730 1-1/63030506 5/16 05 3/8-19 22 1.968 1-9/323030606 3/8 06 3/8-19 22 2.047 1-1/43030608 3/8 06 1/2-14 27 2.165 1-13/323030808 1/2 08 1/2-14 27 2.637 1-5/83030810 1/2 08 5/8-14 30 2.677 1-5/83030812 1/2 08 3/4-14 32 2.677 1-3/43031010 5/8 10 5/8-14 30 2.677 1-7/83031012 5/8 10 3/4-14 32 2.835 1-31/323031212 3/4 12 3/4-14 32 3.307 2-1/83031216 3/4 12 1-11 38 3.425 2-5/323031616 1 16 1-11 38 4.173 2-5/8

Page 26


METRIC FEMALE SWIVEL LIGHT SERIES DKL/DKOL (DIN 3865)

DYNA FLEX PART NO.

HOSEI.D.

DASH

SIZE

THREAD "T"

HEX

MM.

"E"

CUTOFFIN. "C"

376120306 3/16 03 M12-1.5 14 .905376120408 1/4 04 M12-1.5 14 .984376140408 1/4 04 M14-1.5 17 .905376160410 1/4 04 M16-1.5 19 .905376160612 3/8 06 M16-1.5 19 .984376180412 1/4 04 M18-1.5 22 .945376160510 5/16 05 M16-1.5 19 .905376180612 3/8 06 M18-1.5 22 .945376220615 3/8 06 M22-1.5 27 1.063376220815 1/2 08 M22-1.5 27 1.063376261018 5/8 10 M26-1.5 32 1.142376261222 3/4 12 M26-1.5 32 1.220376301222 3/4 12 M30-2 36 1.142376361628 1 16 M36-2 41 1.181

Page 27

METRIC FEMALE 45 ELBOW SWIVEL LIGHT SERIES DKL/DKOL (DIN 3865)

DYNA FLEX PART NO.

HOSEI.D.

DASH SIZE

THREADT

HEX MM "E"

CUTOFF IN. "C"

DROP"H"

378120306 3/16 03 M12-1.5 14 .590 .590378140408 1/4 04 M14-1.5 17 1.023 1.023378160410 1/4 04 M16-1.5 19 1.023 1.063378180412 1/4 04 M18-1.5 22 1.142 1.181378160510 5/16 05 M16-1.5 19 1.142 1.220378180612 3/8 06 M18-1.5 22 1.260 1.299378220615 3/8 06 M22-1.5 27 1.378 1.260378220815 1/2 08 M22-1.5 27 1.693 1.417378261018 5/8 10 M26-1.5 32 1.654 1.810378301222 3/4 12 M30-2 36 1.929 2.008378361628 1 16 M36-2 41 2.283 2.402

METRIC FEMALE 90 ELBOW SWIVEL LIGHT SERIES DKL/DKOL (DIN 3865)

PART NO. HOSE I.D.

DASH

SIZE

THREAD T

HEX

MM.

"E"

CUTOFF IN. "C"

DROP IN. "H"

377120306 3/16 03 M12-1.5 14 .590 .590377140408 1/4 04 M14-1.5 17 1.023 1.023377160410 1/4 04 M16-1.5 19 1.023 1.063377180412 1/4 04 M18-1.5 22 1.142 1.181377160510 5/16 05 M16-1.5 19 1.142 1.220377180612 3/8 06 M18-1.5 22 1.260 1.299377220615 3/8 06 M22-1.5 27 1.378 1.260377220815 1/2 08 M22-1.5 27 1.693 1.417377261018 5/8 10 M26-1.5 32 1.654 1.810377301222 3/4 12 M30-2 36 1.929 2.008377361628 1 16 M36-2 41 2.283 2.402

Page 28

DYNA FLEX Thermoplastic Hose and Fittings METRIC STUD MALE HEAVY SERIES

DYNA FLEX PART NO.

HOSEI.D. IN.

DASH SIZE

THREAD HEX MM "H"

CUTOFF IN. "C"

323160308 3/16 03 M16-1.5 17 1.181323160408 1/4 04 M16-1.5 17 1.063323180410 1/4 04 M18-1.5 19 1.063323200512 5/16 05 M20-1.5 22 1.142323200612 3/8 06 M20-1.5 22 1.142323200614 3/8 06 M22-1.5 22 1.22323240816 1/2 08 M24-1.5 24 1.26323301020 5/8 10 M30-2 30 1.338323301220 3/4 12 M30-2 30 1.378323361225 3/4 12 M36-2 36 1.496323361625 1 16 M36-2 36 1.535323421630 1 16 M42-2 42 1.654

METRIC FEMALE SWIVEL HEAVY SERIES DKL/DKOL (DIN 3865)

PART NO. HOSEI.D.

DASH SIZE

THREAD HEXIN. "H"

CUTOFFIN. "C"

373160308 3/16 03 M16-1.5 19 .984373160408 1/4 04 M16-1.5 19 .984373180410 1/4 04 M18-1.5 22 .945373200512 5/16 05 M20-1.5 24 1.023373200612 3/8 06 M20-1.5 24 1.023373220614 3/8 06 M22-1.5 27 1.063373240816 1/2 08 M24-1.5 30 1.181373301020 5/8 10 M30-2 36 1.417373301220 3/4 12 M30-2 36 1.417373361225 3/4 12 M36-2 46 1.810373361625 1 16 M36-2 46 1.810373421630 1 16 M42-2 50 1.968


MENTOR, OHIO 44060 U.S.A. PHONE: (440) 946-0719 TOLL FREE: (800) 525-8463 FAX: (440) 946-4620

Web Site: www.dynaflexinc.com E-Mail: [email protected]

Page 29

DYNA FLEX Thermoplastic Hose and Fittings METRIC FEMALE 45 ELBOW SWIVEL

HEAVY SERIES DKL/DKOL (DIN 3865)

DYNA FLEX PART NO.

HOSEI.D.

DASH SIZE

THREAD T

HEX

MM.

"E"

CUTOFFIN. "C"

DROP IN.

"H"

375160308 3/16 03 M16-1.5 19 1.378 .630375160408 1/4 04 M16-1.5 19 1.654 .590375180410 1/4 04 M18-1.5 22 1.771 .709375200512 5/16 05 M20-1.5 24 1.968 .787375200612 3/8 06 M20-1.5 24 2.086 .709375220614 3/8 06 M22-1.5 27 2.086 .748375240816 1/2 08 M24-1.5 30 2.599 .709375301020 5/8 10 M30-2 36 2.835 1.023375301220 3/4 12 M30-2 36 3.425 1.181375361225 3/4 12 M36-2 46 2.244 1.220375361625 1 16 M36-2 46 2.835 1.299375421630 1 16 M42-2 50 2.756 1.378

METRIC FEMALE 90 ELBOW SWIVEL HEAVY SERIES DKL/DKOL (DIN 3865)

PART NO. HOSE I.D.

DASH SIZE

THREAD "T"

IN. "E"

CUTOFF

IN. "C"

DROP IN. "H"

374160308 3/16 03 M16-1.5 19 .945 .945374160408 1/4 04 M16-1.5 19 1.023 1.023374180410 1/4 04 M18-1.5 22 1.063 1.181374200512 5/16 05 M20-1.5 24 1.142 1.456374200612 3/8 06 M20-1.5 24 1.338 1.299374220614 3/8 06 M22-1.5 27 1.299 1.299374240816 1/2 08 M24-1.5 30 1.654 1.456374301020 5/8 10 M30-2 36 1.810 1.968374301220 3/4 12 M30-2 36 2.283 2.165374361225 3/4 12 M36-2 46 2.244 2.283374361625 1 16 M36-2 46 2.835 2.599374421630 1 16 M42-2 50 2.756 2.835




Page 30

DYNA FLEX Thermoplastic Hose and Fittings JIS KOMATSU FEMALE FITTING

PART NO. HOSE IN. I.D.

DASH SIZE

THREAD HEX MM. "H"

CUTOFF IN. "C"

0414MJFS 1/4 04 M14-1.5 19 .7870514MJFS 5/16 05 M16-1.5 22 .8270614MJFS 3/8 06 M14-1.5 19 .8270618MJFS 3/8 06 M18-1.5 24 .8270822MJFS 1/2 08 M22-1.5 27 .9451024MJFS 5/8 10 M24-1.5 32 .9841230MJFS 3/4 12 M30-1.5 36 1.1811633MJFS 1 16 M33-1.5 41 1.299

JIS KOMATSU BSP FEMALE FITTING


DASH SIZE

THREAD HEX MM. "H"

CUTOFF IN. "C"

04MJFSBSP 1/4 04 1/4-19 19 .78706MJFSBSP 3/8 06 3/8-19 19 .82708MJFSBSP 1/2 08 1/2-14 27 .94512MJFSBSP 3/4 12 3/4-14 36 1.18116MJFSBSP 1 16 1-11 41 1.299




Page 31


ORFS FEMALE SAEJ1456

DYNA FLEX PART NO.

HOSEI.D.

DASH SIZE

THREAD HEX IN.

"H"

CUTOFFIN. "C"

ORFS-S-04-04 1/4 04 9/16-18 3/4 .787ORFS-S-04-06 1/4 04 11/16-16 7/8 .787ORFS-S-05-06 5/16 05 11/16-16 7/8 .827ORFS-S-06-06 3/8 06 11/16-16 7/8 .827ORFS-S-06-08 3/8 06 13/16-16 7/8 .827ORFS-S-08-08 1/2 08 13/16-16 31/32 .945ORFS-S-08-10 1/2 08 1-14 1-3/16 1.299ORFS-S-08-12 1/2 08 1-3/16-12 1-13/32 1.299ORFS-S-10-10 5/8 10 1-14 1-3/16 1.299ORFS-S-12-10 3/4 12 1-14 1-3/16 1.299ORFS-S-12-12 3/4 12 1-3/16-12 1-13/32 1.338ORFS-S-12-16 3/4 12 1-7/16-12 1-5/8 1.417ORFS-S-16-16 1 16 1-7/16-12 1-5/8 1.456

MALE O-RING BOSS

PART NO. HOSE I.D.

DASH SIZE

THREAD HEX IN. "E"

CUTOFF IN. "C"

2204-704 1/4 04 7/16-20 9/16 15/162204-705 1/4 04 1/2-20 21/32 15/162204-706 1/4 04 9/16-18 21/32 15/162205-706 5/16 05 9/16-18 21/32 15/162206-706 3/8 06 9/16-18 21/32 12206-708 3/8 06 3/4-16 15/16 1-1/82208-708 1/2 08 3/4-16 15/16 1-1/82208-710 1/2 08 7/8-14 1-1/16 1-3/162208-712 1/2 08 1-1/16-12 1-17/64 1-17/162210-710 5/8 10 7/8-14 1-1/16 1-3/162210-712 5/8 10 1-1/16-12 1-17/64 1-17/162212-712 3/4 12 1-1/16-12 1-17/64 1-5/162212-716 3/4 12 1-5/16-12 1-1/2 1-7/162216-716 1 16 1-5/16-12 1-1/2 1-15/32




Page 32


ORFS FEMALE 45 SAEJ1453

PART NO. HOSEI.D. .

DASH SIZE

THREAD HEX IN.

"H"

CUTOFFIN. "C"

DROP IN. "X"

ORFS-45-04-04 1/4 04 9/16-18 3/4 1.570 .512ORFS-45-04-06 1/4 04 11/16-16 7/8 1.614 .551ORFS-45-05-06 5/16 05 11/16-16 7/8 1.730 .551ORFS-45-06-06 3/8 06 11/16-16 7/8 1.968 .590ORFS-45-06-08 3/8 06 13/16-16 7/8 2.008 .630ORFS-45-08-08 1/2 08 13/16-16 31/32 2.362 .827ORFS-45-08-10 1/2 08 1-14 1-3/16 2.402 .866ORFS-45-08-12 1/2 08 1-3/16-12 1-13/32 2.441 .905ORFS-45-10-10 5/8 10 1-14 1-3/16 2.637 .748ORFS-45-12-10 3/4 12 1-14 1-3/16 3.150 .866ORFS-45-12-12 3/4 12 1-3/16-12 1-13/32 3.189 .905ORFS-45-12-16 3/4 12 1-7/16-12 1-5/8 3.228 .945ORFS-45-16-16 1 16 1-7/16-12 1-5/8 3.937 1.181

ORFS FEMALE 90 SAEJ1453





DASH SIZE

THREAD HEX CUTOFF IN. "C"

DROP IN. "X"

ORFS-90-04-04 1/4 04 9/16-18 3/4 1.063 .905ORFS-90-04-06 1/4 04 11/16-16 7/8 1.063 .984ORFS-90-05-06 5/16 05 11/16-16 7/8 1.142 1.063ORFS-90-06-06 3/8 06 11/16-16 7/8 1.338 1.142ORFS-90-06-08 3/8 06 13/16-16 7/8 1.338 1.220ORFS-90-08-08 1/2 08 13/16-16 31/32 1.654 1.378ORFS-90-08-10 1/2 08 1-14 1-3/16 1.654 1.456ORFS-90-08-12 1/2 08 1-3/16-12 1-13/32 1.654 1.535ORFS-90-10-10 5/8 10 1-14 1-3/16 1.810 1.535ORFS-90-12-10 3/4 12 1-14 1-3/16 2.283 1.730ORFS-90-12-12 3/4 12 1-3/16-12 1-13/32 2.283 1.810ORFS-90-12-16 3/4 12 1-7/16-12 1-5/8 2.283 1.889ORFS-90-16-16 1 16 1-7/16-12 1-5/8 2.835 2.322

Page 33


MALE O-RING BOSS SWIVEL 90

PART NO.

HOSE I.D. IN.

DASH SIZE

HEX "E"

DROP "H"

CUTOFFIN. "C"

2208-81090

1/2 08 1-1/16

1-21/32

1-1/8

2210-81090

5/8 10 1-1/16

1-21/32

1-5/32

2212-81290

5/8 10 1-17/64

1-29/32

1-3/16

NPSM SWIVEL FEMALE

DYNA FLEX, INC.

7300 INDUSTRIAL PARK BLVD. MENTOR, OHIO 44060 U.S.A.


1

PART NO. HOSE I.D.

DASH SIZE

THREAD "T"

CUTOFF IN. "C"

HEX IN. "H"

2203-964

3/16 03 1/4-18 .693 3/4

2204-964

1/4 04 1/4-18 .701 3/4

2206-966

3/8 06 3/8-18 .768 27/32

2208-968

1/2 08 1/2-14 .886 1-1/16

Page 34


BLANK INSERT FITTING

DYNA FLEX PART NO.

HOSE

I.D. IN.

DASH

SIZE

HEX

"E"

CUTOFF

IN.

"C" 2204-0000 1/4 04 19 1-1/8 2206-0000 3/8 06 22 29/32 2208-0000 1/2 08 27 1-5/32 2212-0000 3/4 12 32 1-17/64 2216-0000 1 16 38 1-7/16 2220-0000 1-1/4 20 50 1-5/8 2224-0000 1-1/2 24 55 1-11/16 2232-0000 2 32 65 1-25-32

HOSE MENDER

PART NO. HOSE I.D. IN.

DASH SIZE

CUTOFF IN. "C"

2203-2203 3/16 03 11/162204-2204 1/4 04 11/162205-2205 5/16 05 11/162206-2206 3/8 06 11/162208-2208 1/2 08 23/322210-2210 5/8 10 23/322212-2212 3/4 12 3/42216-2216 1 16 13/162220-2220 1-1/4 20 15/16




Page 35


BANJO BSP

PART NO. HOSE

I.D. IN.

DASH

SIZE

HOLE

THREAD

HOLE

MM

RADIUS

MM

"R"

CUTOFF

IN.

"C"

2203-2BSPBANJO 3/16 03 1/8-28 10.1 17 3/42203-4BSPBANJO 3/16 03 1/4-19 13.3 24 12204-2BSPBANJO 1/4 04 1/8-28 10.1 17 12204-4BSPBANJO 1/4 04 1/4-19 13.3 24 12205-4BSPBANJO 5/16 05 1/4-19 16.8 28 12205-6BSPBANJO 5/16 05 3/8-19 13.3 24 12205-4BSPBANJO 5/16 05 1/4-19 16.8 28 12205-6BSPBANJO 5/16 05 3/8-19 13.3 24 12206-6BSPBANJO 3/8 06 3/8-19 21.1 28 12206-8BSPBANJO 3/8 06 1/2-14 16.8 36 1-1/42208-8BSPBANJO 1/2 08 5/8-14 21.1 36 1-1/4

2210-10BSPBANJO 5/8 10 5/8-14 23.1 40 1-1/22212-12BSPBANJO 3/4 12 3/4-14 26.6 45 1-1/22212-16BSPBANJO 3/4 16 1-11 33.5 58 1-15/162216-16BSPBANJO 1 16 1-11 33.5 58 1-31/32

BANJO METRIC

PART NO. HOSE

I.D. IN.

DASH

SIZE

HOLE

THREAD

HOLE

MM

MM

"R"

CUTOFF

IN.

"C"2203-M10-1.5BANJO 3/16 03 M10-1.5 3.1 17 .982204-M10-1.5BANJO 1/4 04 M10-1.5 4.1 17 .982204-M12-1.5BANJO 1/4 04 M12-1.5 4.1 20 .872204-M14-1.5BANJO 1/4 04 M14-1.5 4.1 24 .982205-M14-1.5BANJO 5/16 05 M14-1.5 5.1 24 .982205-M16-1.5BANJO 5/16 05 M16-1.5 5.1 28 1.222205-M18-1.5BANJO 5/16 05 M18-1.5 5.2 32 1.142206-M14-1.5BANJO 3/8 06 M14-1.5 6.1 24 .982206-M16-1.5BANJO 3/8 06 M16-1.5 6.1 28 1.222206-M18-1.5BANJO 3/8 08 M18-1.5 6.2 32 1.142208-M18-1.5BANJO 1/2 08 M18-1.5 8.2 32 1.142208-M22-1.5BANJO 1/2 08 M22-1.5 8.2 36 1.262212-M26-1.5BANJO 3/4 12 M26-1.5 N/A 45 1.652216-M30-1.5BANJO 1 16 M30-1.5 6.2 54 1.69




Page 36


Metric Standpipe

PART NO.

HOSE I.D.

DASH SIZE

PIPE MM "T"

CUTOFF IN. "C"

2203-6mm 3/16 03 6 1-3/162203-8mm 3/16 03 8 1-1/8 2204-6mm 1/4 04 6 1-1/4 2204-8mm 1/4 04 8 1-3/162204-10mm 1/4 04 10 1-9/322204-12mm 1/4 04 12 1-3/162205-10mm 5/16 05 10 1-7/322205-12mm 5/16 05 12 1-3/162206-10mm 3/8 06 10 1-3/162206-12mm 3/8 06 12 1-1/4 2206-14mm 3/8 06 14 1-17/322206-15mm 3/8 06 15 1-1/4 2208-14mm 1/2 08 14 1-17/322208-15mm 1/2 08 15 1-5/162208-16mm 1/2 08 16 1-17/322208-18mm 1/2 08 18 1-3/8 2210-18mm 5/8 10 18 1-3/8 2210-20mm 5/8 10 20 1-3/4 2210-22mm 5/8 10 22 1-9/322212-18mm 3/4 12 20 1-15/322212-20mm 3/4 12 22 1-13/162212-22mm 3/4 12 22 1-1/2 2212-25mm 3/4 12 25 1-15/162216-25mm 1 16 25 2 2216-28mm 1 16 28 1-5/8 2216-30mm 1 16 30 2-1/8




Page 37


Metric Standpipe 90

PART #

HOSE I.D.

DASH SIZE

PIPE MM "T"

CUTOFF IN. "C"

DROP IN. "H"

2203-6mm90 3/16 03 6 7/8 1-1/4 2203-8mm90 3/16 03 8 7/8 1-1/4 2204-6mm90 1/4 04 6 1 1-3/8 2204-8mm90 1/4 04 8 1 1-13/32

2204-10mm90 1/4 04 10 1 1-7/16 2204-12mm90 1/4 04 12 1 1-7/16 2205-10mm90 5/16 05 10 1-1/8 1-9/16 2205-12mm90 5/16 05 12 1-1/8 1-5/8 2206-10mm90 3/8 06 10 1-9/32 1-9/16 2206-12mm90 3/8 06 12 1-9/32 1-9/16 2206-14mm90 3/8 06 14 1-9/32 1-3/4 2206-15mm90 3/8 06 15 1-9/32 1-5/8 2208-14mm90 1/2 08 14 1-17/32 1-31/32 2208-15mm90 1/2 08 15 1-17/32 1-13/16 2208-16mm90 1/2 08 16 1-17/32 2 2208-18mm90 1/2 08 18 1-5/8 2-1/4 2210-18mm90 5/8 10 18 1-5/8 2-1/4 2210-20mm90 5/8 10 20 1-7/8 2-9/16 2210-22mm90 5/8 10 22 2-1/16 2-25/32 2212-20mm90 3/4 12 22 1-15/16 2-9/16 2212-22mm90 3/4 12 22 2-1/8 2-25/32 2212-25mm90 3/4 12 25 2-1/4 3 2216-25mm90 1 16 25 2-9/32 3 2216-28mm90 1 16 28 2-9/16 3-5/16 2216-30mm90 1 16 30 2-51/8 3-1/2




Page 38


METRIC STANDPIPE 45

PART NO.

HOSE I.D..

DASH SIZE

PIPE MM "T"

CUTOFF IN. "C"

DROP IN. "H"

2203-6mm45 3/16 03 6 1 1-1/2 2203-8mm45 3/16 03 8 1 1-1/2 2204-6mm45 1/4 04 6 1-3/16 1-7/8 2204-8mm45 1/4 04 8 1-1/8 1-25/32

2204-10mm45 1/4 04 10 1-3/16 1-7/8 2205-10mm45 5/16 05 10 1-3/16 1-7/8 2205-12mm45 5/16 05 12 1-1/8 1-9/16 2206-10mm45 3/8 06 10 1-11/32 2-9/32 2206-12mm45 3/8 06 12 1-11/32 2-9/32 2206-14mm45 3/8 06 14 1-17/32 2-1/2 2206-15mm45 3/8 06 15 1-11/32 2-9/32 2208-14mm45 1/2 08 14 1-11/16 2-29/32 2208-15mm45 1/2 08 15 1-17/32 2-25/32 2208-16mm45 1/2 08 16 1-21/32 2-31/32 2208-18mm45 1/2 08 18 1-1/4 2-7/16 2210-18mm45 5/8 10 18 1-1/4 2-7/16 2210-20mm45 5/8 10 20 1-11/32 2-7/16 2210-22mm45 5/8 10 22 1-3/8 2-11/16 2212-20mm45 3/4 12 20 1-3/8 2-11/16 2212-22mm45 3/4 12 22 1-3/8 2-11/16 2212-25mm45 3/4 12 25 1-17/32 2-31/32 2216-25mm45 1 16 25 1-17/32 2-15/16 2216-28mm45 1 16 28 1-1/2 2-7/8 2216-30mm45 1 16 30 1-11/16 3-5/16




Page 39


BLANK INSERT FITTING

DYNA FLEX PART NO.

HOSE

I.D. IN.

DASH

SIZE

HEX

"E"

CUTOFF

IN.

"C" 2204-0000 1/4 04 19 1-1/8 2206-0000 3/8 06 22 29/32 2208-0000 1/2 08 27 1-5/32 2212-0000 3/4 12 32 1-17/64 2216-0000 1 16 38 1-7/16 2220-0000 1-1/4 20 50 1-5/8 2224-0000 1-1/2 24 55 1-11/16 2232-0000 2 32 65 1-25-32

HOSE MENDER

PART NO. HOSE I.D. IN.

DASH SIZE

CUTOFF IN. "C"

2203-2203 3/16 03 11/162204-2204 1/4 04 11/162205-2205 5/16 05 11/162206-2206 3/8 06 11/162208-2208 1/2 08 23/322210-2210 5/8 10 23/322212-2212 3/4 12 3/42216-2216 1 16 13/162220-2220 1-1/4 20 15/16




Page 40


KARCHER MALE


DASH SIZE

THREAD "T"

CUTOFF MM "C"

4-22X1.5GUN 1/4 04 M22X1.5 33 5-22X1.5GUN 5/16 05 M22X1.5 33




Page 41


D105 QK HYDRAULIC HOSE CRIMPER

FEATURES

- Adjustable Ram Retraction Stop to help customize the hose assembly crimping speed based on your fitting. Automatic shut off for precise crimps. - HP 110 Volt Valpower Hydraulic Pump powerful enough to crimp application in seconds. -Micro crimp adjuster enables user to adjust in metric and nonmetric increments. - Fully adjustable to accommodate a wide range of different hose fittings without the need for special shims or spacers. -Die sets are easy to install and replace. Complete range of dies and accessories are available.

Micro-Crimp Adj

Page 42

2006 Hose Catalog request form

Company Name: ____________________________________ Address: __________________________________________ City: _____________________________________________ State: _______________________ Zip: _________________ Phone: _______________________FAX _________________ E-mail: ___________________________________________ Name: ____________________________________________ Number of catalogs requested: _______________ Dyna Flex Inc. Updates: New Products, Specials, Pricing……… Please select how you would like to receive updates Fax E-mail Dyna Flex Inc. will mail catalog(s) upon Receipt of signed catalog request form. Signature: ______________________________ Date: __________

Dyna Flex Inc. 7300 Industrial Park Blvd., Mentor, Oh 44060

Phone: 800-525-8463 Fax: 440-946-4620 E-mail: [email protected]

www.dynaflexinc.com

Page 43

Documents

DynaFlex Thermplastic Hose Catalog - Flex Inc - Adapters Inc