Dwa 6 - Αντιγραφή

8/18/2019 Dwa 6 - Αντιγραφή

1/23


2/23

Motorcycle data/dealership details

Motorcycle data

Model

Vehicle identification number

Colour code

Date of first registration

Registration number

Dealership details

Person to contact in Service department

Ms/Mr

Phone number

Dealership address/phone number (com-pany stamp)


3/23

Details described or illustratedin this booklet may differ fromthe motorcycle's actual specifica-tion as purchased, the accessor-ies fitted or the national-market

specification. No claims will beentertained as a result of suchdiscrepancies.

Dimensions, weights, fuel con-sumption and performance dataare quoted to the customary tol-erances.

The right to modify designs,equipment and accessories isreserved.

Errors and omissions excepted.

© 2008 BMW Motorrad

Not to be reproduced eitherwholly or in part without written

permission from BMW Motorrad,After Sales.

Printed in Germany.


4/23

BMW recommends

Order No. 01 41 7 714 371

05.2008, 5th edition*01417714371*


5/23

Welcome to BMW Mo-torrad

We congratulate you on yourchoice of the BMW MotorradDWA 6 anti-theft alarm.

Familiarise yourself with all theapplicable procedures before youuse the system for the first time.These instructions for use con-tain the information you need, soplease study them carefully.

If you have questions concern-ing this BMW Motorrad anti-theftalarm, your authorised BMW Mo-torrad dealer will gladly provideadvice and assistance.

We hope that you will enjoy us-ing your DWA 6 system and thatall your journeys will be pleasant

and safe.

BMW Motorrad.


6/23

Table of Contents

You can also consult the index atthe end of this Rider's Manual if you want to find a particular topic

or item of information.1 General instructions . . . . 3Overview . . . . . . . . . . . . . . . . . . . . . 4Abbreviations andsymbols . . . . . . . . . . . . . . . . . . . . . . 4Currency . . . . . . . . . . . . . . . . . . . . . 4Technical data . . . . . . . . . . . . . . . 4

2 Overview . . . . . . . . . . . . . . . . . 5General information about theanti-theft alarm . . . . . . . . . . . . . . . 6Controls . . . . . . . . . . . . . . . . . . . . . . 6

3 Operation.. .. ... .. .. ... .. . 7Activation . . . . . . . . . . . . . . . . . . . . 8Alarm function . . . . . . . . . . . . . . . . 9Deactivation . . . . . . . . . . . . . . . . . 10

Programming . . . . . . . . . . . . . . . . 11Registration of the remotecontrol . . . . . . . . . . . . . . . . . . . . . . 12Synchronisation . . . . . . . . . . . . . 14Battery . . . . . . . . . . . . . . . . . . . . . . 14

4 Technical data .. .. .. .. .. 17Anti-theft alarm . . . . . . . . . . . . . . 18Remote control . . . . . . . . . . . . . . 18


7/23

General instructions

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Abbreviations and symbols . . . . . . . . . . 4

Currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical data . . . . . . . . . . . . . . . . . . . . . . . 4

13

z G e n e r a l i n

s t r u c t i o n s


8/23

Overview

Chapter 2 of these instructionsfor use will provide you withan initial overview of the anti-

theft alarm. Chapter 3 describeshow to use the anti-theft alarm,Chapter 4 contains a list of the most important technicalfeatures.

Abbreviations andsymbols

Indicates warnings that youmust comply with for reas-

ons of your safety and the safetyof others, and to protect yourmotorcycle against damage.

Specific instructions onhow to operate, control, ad-

just or look after items of equip-ment on the motorcycle.

Indicates the end of anitem of information.

Instruction.

Result of an activity.

Reference to a page with

more detailed informa-tion.

Indicates the end of apassage relating to spe-cific accessories or itemsof equipment.

Tightening torque.

Item of technical data.

Currency

The high safety and quality levels

of BMW accessories are ensuredby a process of continuing evol-ution. Because of this, the ac-cessory you have purchased maydiffer from the information sup-plied in the instructions for use.

Nor can BMW Motorrad entirelyrule out errors and omissions.We hope you will appreciate thatno claims can be entertained onthe basis of the data, illustrations

or descriptions in this manual.

Technical data

All dimensions, weights andpower ratings stated in theinstructions for use are quoted tothe standards and comply with

the tolerance requirements of theDeutsches Institut für Normunge.V. (DIN). Versions for individualcountries may differ.

14

z G e n e r a l i n

s t r u c t i o n s


9/23

Overview

General information about the anti-theft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

25

z O v e r v i e w


10/23

General informationabout the anti-theftalarm

Any attempt to move the motor-

cycle, change its position, startit without an authorised key ordisconnect the starter battery willtrigger the alarm. The sensitivityof the system is parameterisedso that slight vibrations will nottrigger the alarm. Once the sys-tem has been activated, any at-

tempt to tamper with the motor-cycle is indicated acoustically bythe siren and visually by all fourturn indicators flashing in unison.

You can change some of youralarm system's parameters to suityour personal preferences.

Conserving battery powerIn order to conserve the powerof the starter battery and ensurethat the motorcycle will start, theanti-theft alarm switches off auto-

matically a few days after beingactivated. In most cases, how-ever, it will remain active for atleast seven days.

Radio interferenceRadio systems or devices trans-mitting on the same frequencyas the remote control of the anti-theft alarm can interfere with op-eration of the system. If prob-lems of this nature occur, pointthe remote control toward the

motorcycle from another direc-tion.

Controls

1 Left button (ribbed) ( 8)

2 Right button ( 9)

3 LED

See your Rider's Manualfor details of the position of

the status-indicator LED on themotorcycle.

26

z O v e r v i e w


11/23

Operation

Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Alarm function . . . . . . . . . . . . . . . . . . . . . . . 9

Deactivation . . . . . . . . . . . . . . . . . . . . . . . . 10

Programming . . . . . . . . . . . . . . . . . . . . . . . 11

Registration of the remote con-trol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Synchronisation . . . . . . . . . . . . . . . . . . . . . 14

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

37

z O p e r a t i o n


12/23

Activation

Activating with motionsensor

To activate the alarm function,press button 1 on the remotecontrol once or switch off theignition (if programmed).

If the alarm function isactivated by the ignition beingswitched off, a 30-second

delay precedes the activationphase.

Activation phase starts.

Turn indicators flash twice.

Alarm tone sounds twice (if programmed).

The telltale light on the mo-torcycle starts flashing (0.1second ON, 0.9 second OFF).

Activation phase

The anti-theft alarm needs15 seconds to go active. Noalarm will be triggered during thistime.

Conserving battery power

If you decide to activate thealarm function more than oneminute after switching off theignition, you must press button 1

for longer than one second. If itis left deactivated for longer thanapproximately one hour, the anti-theft alarm shuts itself down inorder to conserve battery power.

If you want to activate the alarmfunction after this period of timeyou must switch the ignition onand then off again.

Motion sensor whenmotorcycle is to betransported

If you want to transport yourmotorcycle by train or on atrailer, for example, it is advisableto switch off the motionsensor. If the motion sensoris not switched off the severemovements occurring in transit

could trigger the alarm.

38

z O p e r a t i o n


13/23

Deactivating motionsensor

Press button 1 on the remote

control a second time duringthe activation phase.

Turn indicators flash threetimes.

Alarm tone sounds three times.

Motion sensor is deactivated.

Alarm function

Alarm triggers

An alarm can be triggered by

the motion sensor

an attempt to switch on theignition with an unauthorisedkey

an attempt to disconnect theanti-theft alarm from the starterbattery (the built-in battery inthe anti-theft alarm automatic-ally cuts in to provide power)

Alarm

An alarm lasts for 26 seconds.The system is active again an-

other 12 seconds later. You caninterrupt an alarm at any time bypressing button 2 on the remotecontrol. This function does notchange the status of the anti-theft alarm.

While an alarm is in progress analarm tone sounds and the turn

indicators flash. You can programthe type of alarm tone.

39

z O p e r a t i o n


14/23

Reason for an alarm

Once you have deactivated thealarm function, the anti-theftalarm telltale light flashes in codefor one minute if the alarm wastriggered while active: the codeindicates the reason for thealarm:

1x flashing: Motion sensor;motorcycle was rocked forward/back

2x flashing: Motion sensor;

motorcycle was tilted to theside

3x flashing: Attempt to switchon the ignition with unauthor-ised key

4x flashing: Attempt to discon-nect the anti-theft alarm fromthe starter battery

Acoustic indication thatalarm was triggered

A signal tone sounding onceafter you switch on the ignitionis an indication that an alarm wastriggered since the alarm functionwas last activated.

Deactivation

Deactivating alarmfunction

Press button 2 on the remotecontrol once or switch on theignition using an authorisedkey.

Note that you can deactiv-ate the alarm function with

the ignition key only when the killswitch is in the RUN position.

If you use the remote con-trol to deactivate the alarm

function and do not follow upby switching on the ignition, thealarm function is automaticallyreactivated after 30 seconds if the "activation after ignition off"parameter is set.

Turn indicators flash once.Alarm tone sounds once (if programmed).

Alarm function is deactivated.

Conserving battery power

After the alarm function has beenactive for approximately one hour,

the receiver for the remote con-trol in the anti-theft alarm shutsdown to conserve battery power.After this period has elapsed theignition has to be switched on in

310

z O p e r a t i o n


15/23

order for the alarm function to bedeactivated.

Programming

Programming options

You can customise the follow-ing parameters of your anti-theftalarm:

Confirmation alarm tone afteractivation/deactivation of theanti-theft alarm in addition tovisual confirmation by turn in-

dicators flashingRising and falling or intermittentalarm tone

Automatic activation of thealarm function after the ignitionis switched off

Default settings

The anti-theft alarm ships withthe following default settings:

Alarm tone sounds as confirm-ation after activation/deactiva-tion of the alarm function: No

Alarm tone: Intermittent

Automatic activation of the

alarm function after the ignitionis switched off: No

Programming anti-theftalarm

Deactivate the alarm function.

Switch on the ignition.Press button 1 three times.

Acknowledgement tone soundsonce.

Within ten seconds, switch off the ignition.

Press button 2 three times.


Within ten seconds, switch onthe ignition.

Acknowledgement tone soundsthree times.

The programming function isactive.

Programming is a sequence of four steps, although no functionis assigned to step No. 2. Thenumber of times the anti-theftalarm telltale light on the mo-torcycle flashes indicates whichstep in the programming se-quence is active. An alarm tonesounds as confirmation when

you press button 1; an acknow-ledgement tone sounds whenyou press button 2.

311

z O p e r a t i o n


16/23

Step 1: Do you want a con-firmation tone to sound afteractivation/deactivation of theanti-theft alarm?

Yes:

Press button 1.

No:

Press button 2.

Step 2:

There is no function assigned tothis step.

Press button 1 or button 2.

Step 3: Which alarm tone doyou want to use?

Rising and falling:

Press button 1.

Intermittent:

Press button 2.Step 4: Do you want to havethe alarm function activatedautomatically after the ignitionis switched off?

Yes:

Press button 1.

No:

Press button 2.

Under whatcircumstances isprogramming aborted?

Programming is aborted

if the ignition is switched off before completion of the laststep in the programming se-quence

or automatically, if more than30 seconds elapse betweenany two steps in the program-ming sequence.

The new settings are not saved if programming is aborted.

Saving programmedsettings

Programming is saved

when the ignition is switchedoff after completion of the laststep in the programming se-quence

or automatically 30 secondsafter completion of the laststep in the programming se-quence

The anti-theft alarm telltale lightstops flashing and four acknow-ledgement tones sound.

Registration of theremote control

When is it necessary toregister a remote control?

If you want to register an addi-tional remote control or registera remote control as a replace-ment for one that has been mis-laid, you must always register all

312

z O p e r a t i o n


17/23

the remote control units with theanti-theft alarm. You can registera maximum of four remote con-trol units.

Registering remotecontrol

Deactivate the alarm function.

Switch on the ignition.


Acknowledgement tone sounds

once.Within ten seconds, switch off the ignition.



Within ten seconds, switch onthe ignition.

Acknowledgement tone sounds

twice.You can now register a maximumof four remote control units withthe anti-theft alarm. Registrationis a three-step process for eachremote control.

Press and hold down button 1and button 2.

LED flashes for ten seconds.

As soon as the LED goes out,release button 1 and button 2.

LED lights up.


Alarm tone sounds once.

LED goes out.

Remote control has been re-gistered.

Repeat this three-step proced-ure for each additional remotecontrol.

Termination of registration

Registration is terminated when

four remote control units havebeen registered

the ignition is switched off

30 seconds elapse without abutton being pressed after theignition has been switched off

30 seconds elapse without abutton being pressed after aremote control unit has been

registered

When registration terminates theLED flashes and the acknow-ledgement tone sounds threetimes.

313

z O p e r a t i o n


18/23

Synchronisation

When is it necessary tosynchronise the remotecontrol?

The remote control has to besynchronised if the buttons of the remote control have beenpressed more than 256 timesoutside the receiver's range.Once this limit has been reached,the receiver on the motorcyclewill no longer react to the signals

from the remote control.

Synchronising remotecontrol

Press and hold down button 1

and button 2.LED flashes for ten seconds.

As soon as the LED goes out,release button 1 and button 2.

LED lights up.


LED goes out.

Remote control has been syn-chronised.

Battery

When does the batteryhave to be changed?

The battery in the remote control

is due to be changed after ap-proximately 2 - 3 years. You cantell that the battery is weak if theLED does not light up or lightsup only briefly when a button ispressed.

Changing battery

Remove screw 4 and removebottom part of housing 5.

Slide old battery 8 forwardfrom under retainer 6.

314

z O p e r a t i o n


19/23

Using a battery of thewrong type or inserting the

battery with the polarity reversedcan cause irreparable damage tothe device.

Use only the specified type of battery (see "Technical Data").When inserting the battery,always make sure polarity iscorrect.

Slip the new battery into posi-tion, making sure that the pos-

itive terminal of the battery isfacing up.

Position the bottom part of thehousing at projection 9 of thefront edge and close the hous-ing, noting two guide pins 7.

Install screw 4.

The LED on the remote con-

trol lights up, indicating that theremote control has to be syn-chronised.

To synchronise the remotecontrol, make sure that it iswithin range of the receiver and

press button 1 twice.LED 3 starts flashing and thengoes out after a few seconds.

The remote control is againready for use.

315

z O p e r a t i o n


20/23

316

z O p e r a t i o n


21/23

Technical data

Anti-theft alarm . . . . . . . . . . . . . . . . . . . . . 18

Remote control . . . . . . . . . . . . . . . . . . . . . 18

417

z T e c

h n i c a l d a t a


22/23

Anti-theft alarm

Time to active after activation 15 s

Alarm duration 26 s

Activation time between two alarms 12 sTemperature range -40...85 °C

Operating voltage 9...16 V

Remote control

Range of the remote control 10 m

Reception standby for signal from remote control 1 h, After ignition off Signal frequency 25 kHz, Broadband

Transmission frequency 433.92 MHz

Operating voltage 3 V

Battery type CR 2032

Battery type Lithium

418

z T e c

h n i c a l d a t a


23/23

AAbbreviations and symbols, 4

Activatingwith motion sensor, 8

Alarm function

Deactivating, 10

BBattery

changing, 14

CCurrency, 4

DDeactivating

Alarm, 10

Motion sensor, 9

Default settings, 11

MMotion sensor

Deactivating, 9

PProgramming, 11

RRegistration

Remote control, 13

Remote controlregistering, 13

synchronising, 14

TTechnical data

Standards, 4

519

z I n d e x

Documents

Dwa 6 - Αντιγραφή