Upload
gtgreat
View
213
Download
0
Embed Size (px)
Citation preview
EEE 420 Digital Signal Processing
Instructor : Erhan A. Ince E-mail: [email protected]
Web page address:http://faraday.ee.emu.edu.tr/eee420http://faraday.ee.emu.edu.tr/eaince
Digital Signal Processing And Its Benefits By a signal we mean any variable that carries or contains some kind of information that can be conveyed, displayed or manipulated.
Examples of signals of particular interest are:
- speech, is encountered in telephony, radio, and everyday life
- biomedical signals, (heart signals, brain signals)
- Sound and music, as reproduced by the compact disc player
- Video and image,
- Radar signals, which are used to determine the range and bearing of distant targets
Attraction of DSP comes from key advantages such as :
* Guaranteed accuracy: (accuracy is only determined by the number of bits used) * Perfect Reproducibility: Identical performance from unit to unit
ie. A digital recording can be copied or reproduced several times with no loss in signal quality
* No drift in performance with temperature and age
* Uses advances in semiconductor technology to achieve:(i) smaller size (ii) lower cost (iii) low power consumption (iv) higher operating speed
* Greater flexibility: Reprogrammable , no need to modify the hardware * Superior performance
ie. linear phase response can be achieved complex adaptive filtering becomes possible
Disadvantages of DSP
* Speed and Cost DSP designs can be expensive, especially when large bandwidth signals
are involved. ADC or DACs are either to expensive or do not have sufficient resolution for wide bandwidth applications.
* DSP designs can be time consuming plus need the necessary resources (software etc)
* Finite word-length problems If only a limited number of bits is used due to economic considerations serious degradation in system performance may result.
Application Areas
Image Processing Instrumentation/Control Speech/Audio MilitaryPattern recognition spectrum analysis speech recognition secure communications
Robotic vision noise reduction speech synthesis radar processing
Image enhancement data compression text to speech sonar processingFacsimile position and rate digital audio missile
guidanceanimation control equalization
Telecommunications Biomedical Consumer applicationsEcho cancellation patient monitoring cellular mobile phonesAdaptive equalization scanners UMTS ADPCM trans-coders EEG brain mappers digital television Spread spectrum ECG Analysis digital camerasVideo conferencing X-Ray storage/enhancement internet phone
etc.
Key DSP Operations
1. Convolution2. Correlation 3. Digital Filtering4. Discrete Transformation5. Modulation
Convolution Convolution is one of the most frequently used operations in DSP. Specially in digital filtering applications where two finite and causal sequences x[n] and h[n] of lengths N1 and N2 are convolved
0
][][][][][][][kk
knxkhknxkhnxnhny
where, n = 0,1,…….,(M-1) and M = N1 + N2 -1
This is a multiply and accumulate operation and DSP device manufacturers have developed signal processors that perform this action.
Correlation There are two forms of correlation :
1. Auto-correlation 2. Cross-correlation
1. The cross-correlation function (CCF) is a measure of the similarities or shared properties between two signals. Applications are cross-spectral analysis, detection/recovery of signals buried in noise, pattern matching etc.
Given two length-N sequences x[k] and y[k] with zero means, an estimate of their cross-correlation is given by:
,...2,1,0
00 21 n
rr
nrn
yyxx
xyxy
Where, rxy(n) is an estimate of the cross covarience
The cross-covarience is defined as
1
0
21
0
2
1
0
1
0
][1)0(,][1)0(
,...2,1,0][][1
,...2,1,0][][1
N
kyy
N
kxx
nN
k
nN
kxy
kyN
rkxN
r
nkynkxN
nnkykxNnr
2. An estimate of the auto-correlation of an length-N sequence x[k] with zero mean is given by
][nxx
2,1,0,]0[][][ n
rnrn
xx
xxxx
Digital FilteringThe equation for finite impulse response (FIR) filtering is
1
0][][][
N
kknxkhny
Where, x[k] and y[k] are the input and output of the filter respectively and h[k] for k = 0,1,2,………,N-1 are the filter coefficients
z-1
+
z-1 z-1
+ +
z-1
y(n)
x(n)
x xxxb0 b1 b2 bN-1
Filter structureFilter structure
1
0
N
kk knxbny
A common filtering objective is to remove or reduce noise from a wanted signal.
(a) (b) (c)
(d) (e) (f)
Figure : Reconstructed bi-level text images for degradation caused by h1 and AWGN.(a) Original, (b) 2D Inverse, (c) 2D Wiener, (d)PIDD, (e) 2D VA-DF, (f) PEB-FCNRT
Discrete Transformation Discrete transforms allow the representation of discrete-time signals in the
frequency domain or the conversion between time and frequency domain representations.
Many discrete transformations exists but the discrete Fourier transform (DFT) is the most widely used one.
DFT is defined as:
NjN
n
nk eWwhereWnxkX21
0][)(
IDFT is defined as:
10,)(1][1
0
NnWkXN
nxN
k
knN
MATLAB function for DFT
function [Xk] = dft (xn,N)% Computes Discrete Fourier Transform% -------------------------------------------------------% Xk = DFT coefficient array over 0<= k <= N-1% xn = N-point finite duration sequence % N = Length of DFT%n = [ 0:1:N-1];k= [0:1:N-1];WN = exp(-j*2*pi/N);nk = n.*k;WNnk = WN .^ nk;Xk = xn * WNnk;
Matlab Function for IDFTfunction [xn] = idft(Xk,N)% Computes the Inverse Discrete Transformn = [ 0:1:N-1];k= [0:1:N-1];WN = exp(-j*2*pi/N);nk=n’*k;WNnk = WN .^(-nk);xn = (Xk * WNnk) / N;
Example
Let x[n] be a 4-point sequence
otherwise
nnx
,030,1
][
>>x=[1, 1, 1, 1];>>N = 4; >>X = dft(x,N);>>magX = abs(X) ; >>phaX = angle(X) * 180/pi;
magX= 4.0000 0.0000 0.0000 0.0000
phaX=0 -134.981 -90.00 -44.997
ModulationDiscrete signals are rarely transmitted over long distances or stored in large quantities in their raw form.
Signals are normally modulated to match their frequency characteristic to those of the transmission and/or storage media to minimize signal distortion, to utilize the available bandwidth efficiently, or to ensure that the signal have some desirable properties.
Two application areas where the idea of modulation is extensively used are:1. telecommunications2. digital audio engineering
High frequency signal is the carrier The signal we wish to transmit is the modulating signal
Three most commonly used digital modulation schemes for transmitting Digital data over bandpass channels are:
Amplitude shift keying (ASK) Phase shift keying (PSK) Frequency shift keying (FSK)
When digital data is transmitted over an all digital network a scheme known
As pulse code modulation (PCM) is used.