Upload
phungkhue
View
221
Download
0
Embed Size (px)
Citation preview
www.OPWILL.com
OPWILL TECHNOLOGIES (BEIJING) CO., LTD.
OTM2515/2516/2517 155M/622M/2.5GSDH/SONET Test Module
OTM2515 (155M), OTM2516 (622M), and OTM2517
(2.5G)SDH/SONET Module is a battery-operated
handheld test solution for testing legacy PDH/DSn,
SDH/SONET circuits from 2.5Gbps to 2Mbps/1.5Mbps,
both in-service and out-of-services configuration
installation, maintenance, and troubleshooting
applications, supports overhead monitoring, APS
timing etc. OTM2515 can be upgraded to OTM2516 or
OTM2517. OTM2516 can be upgraded to OTM2517.
This module is compatible with OTP6200v2 (OPWILL
Intelligent Network Test Platform).
DS1/DS3, E1/E3/E4/STM-1 (BNC port);
E1 (RJ45 port);
STM-1/STM-4/STM-16 and OC-3/OC-12/OC-48 SDH/SONET (SFP port);
Support bit error ration test and performance analysis;
Support SDH/SONET overhead control and decode;
Pointer monitoring and adjustment, G.783 pointer test sequences generation;
APS time measurement;
Comprehensive payload mapping selection from VC4-16c/STS-48c (contiguous concatenation) to VC12/VT2, VC11/VT1.5, including PDH/DSn payload (E1/E2/E3/E4, DS1/DS3).
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
Platform Briefs: OTP6200
Compact and lightweight designed;
Graphical user interface, easy to operate;
6.5inches outdoor-enhanced LCD colour touch screen;
Ultra-high capacity field-exchangeable Li-ion
battery pack extends testing time;
Powerful modular intelligent network test platform;
Dial, number keys and function keys for flexible scrolling and selecting;
Remote control by PC using 10/100M Base-
T port.
Modules Briefs: OTM2515, OTM2516, and OTM2517
PDH 155M
SDH/SONET 622M
SDH/SONET 2.5G SDH/SONET
OTM2515 √ √ (Can be upgraded to 2516) (Can be upgraded to 2517)
OTM2516 √ √ √ (Can be upgraded to 2517)
OTM2517 √ √ √ √
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
Key Feature:
BNC port for DS1/DS3; BNC port for E1/E3/E4/STM-1;
RJ48 port for E1; SFP port for STM-1/STM-4/STM-16;
SFP port for OC-3/OC-12/OC-48; Bit error ratio and performance
analysis;
SDH/SONET overhead control and decode;
Pointer monitoring and adjustment, G.783 pointer test sequences generation.
Applications:
Out-of-Service Test:
End-to-end error free transmission verification;
Automatic protection switching verification;
SDH/SONET mapping verification down to VC12/VT1.5.
Round Trip Delay:
In-Service Test:
Through mode;
In-service monitoring protected monitoring points or optical splitters;
Overhead bytes monitoring and decoding;
Pointer monitoring.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
General Specifications: OTP6200 + OTM2515/OTM2516/OTM2517
GENERAL SPECIFICATIONS
User Interface
Screen 6.5 Inch TFT Touch Screen (640 x 480);
Other Interface
USB USB2.0, A type, 2;
USB2.0 Mini B type, 1;
Ethernet Ethernet 10/100, RJ45;
Audio 3.5mm Audio Interface;
Storage 8G;
Physical Specifications
Temperature Operating:-10°C to 50°C;
Storage:-40°C to 70°C;
Relative Humidity 0% to 95% (non-condensing);
Size(H×W×D) OTP6200: 319mm x 202mm x 105mm;
OTM2515/2516/2517: 25mm x 97mm x 259mm;
Weight OTP6200: 2.8kg;
OTM2515/2516/2517: 0.4kg;
Vibrancy 10Hz to 500Hz < 1.5g (on 3 main axes);
Mechanical Shock 6 sides, 8 edges < 760cm, according to GR-196-CORE;
EMC
EN55022/CIPSR22;
EN61000-3-2;
EN55024;
Battery and Power Supply
Battery Rechargeable Li-lon battery;
Working time: 4 hours;
Charging time: 6 hours (typical: 25°C);
Power Source Input: 100-240VAC, 50-60Hz, 2A;
Output: 19VDC, 4A.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
Technical Specifications: OTM2515/OTM2516/OTM2517
SDH and SONET
SDH and SONET Test
Port STM-16/STM-4/STM-1, OC-48/OC-12/OC-3 optical interface: SFP, 1 port; User selectable optical module: 1310nm, 1550nm STM-1e, STS-3 electrical interface: BNC, 1 port;
Measurement Out-of-service mode; In-service mode;
Operation Through mode; Pointer-to-pointer mode; Enhance through mode; Can be changed SOH/TOH, can injection alarms and errors under Enhance Through Mode.
Frame and Scramble
SDH: complies with latest version ITU-T G.707;
SONET: complied with latest version Telcordia GR-253;
Line Code NRZ
Transmitter Clock
Internal clock: Accuracy: 4.6ppm, up to 2ppm;
Clock Offset: ±100ppm (1ppm steps);
Recovered clock;
TTL level external 2.048MHz clock;
E1: 2.048Mbps; DS1: 1.544Mbps;
Receive Single Rate
±100ppm;
Frequency deviation indication resolution: ±1ppm;
TCM Frame Format
ITU-T G.783, G.707 Annex D and Annex E, POH bytes: HP-N1 (SDH); LP-N1 (SDH); LP-N2 (SDH); Z5 (SONET); Z6 (SONET);
TCM access point identifier (Apid): 15 bytes ASCII sequence, CRC-7;
SDH Mapping
SONET Mapping
Alarm
Alarm can to be detected and generated: SDH: LOS, LOF, OOF, MS-AIS, MS-RDI, AU-AIS, AU-LOP, HP-PLM, HP-UNEQ, HP-TIM, HP-
RDI, TU-LOM, TU-AIS, TU-LOP, LP-PLM, LP-UNEQ, LP-TIM, LP-RDI, LP-RFI, LSS;
SONET: LOS, LOF, OOF, AIS-L, RDI-L, AIS-P, LOP-P, TIM-P, PLM-P, UNEQ-P, RDI-P, LOM-V, AIS-V, LOP-V, PLM-V, UNEQ-V, RDI-V, TIM-V, LSS;
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
SDH and SONET Test
Alarm
TCM: TC-LTC, TC-TIM, TC-UNEQ, TC-AIS, TC-RDI, TC-ODI;
Alarm generation mode: Continuous; Alternate; Burst;
Error
Error can be detected and generated: SDH: FAS, B1, B2, MS-REI, HP-B3, HP-REI, LP-B3, LP-BIP2, LP-REI, Bit Error;
SONET: FAS, B1, B2, REI-L, B3, REI-P, B3-V, BIP2-V, REI-V, Bit Error;
TCM: TC-IEC, TC-BIP2, TC-REI, TC-OEI;
Error generation mode: Single; Continuous; Alternate; Burst; Rate; N-frame;
BERT Pattern
Pattern generation and monitor for O.181 bulk test pattern;
Support to generate and detect:
PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31;
Support reversed PRBS pattern: 16bit user define pattern;
Pointer Support AU/TU, STS/VT pointer monitor and generation;
Support ITU-T G.783 pointer test sequences;
Display pointer value of receiver side;
Overhead
Generation of section/transport and path overhead bytes;
Display of current section/transport and path overhead bytes;
All overhead can be decoded, including decoded J0, J1, J2 byte;
All overhead and anyone overhead PRBS BER testing;
Just All overhead and anyone overhead PRBS BER (Including with DCC) testing;
256 frames overhead capture and decode; SDH Tributary
Scan DS1 embedded in selected VC-11;
E1 embedded in selected VC-12;
E3/DS3 embedded in selected VC-3;
E4 embedded in selected VC-4;
SONET Tributary Scan
DS1 embedded in selected VT-1.5;
E1 embedded in selected VT-2;
E3/DS3 embedded in selected STS-1;
E4 embedded in selected STS-3c;
Smart Scan Remote single auto detects and auto setup for SDH analyser;
SDH and SONET Result
Status Display information of current status: Alarms and errors;
Frequency deviation;
Actual bit rate;
Frequency ;
Input power of optical signal;
Statistics Event log display: Alarms (seconds); Errors (count and rate);
Pointer operations; Start/stop time;
All events refresh with 1 second resolution;
Histogram All alarms and errors detected can be display in histogram;
Error Performance
G.821/G.826/G.828/G.829/M.2100/M.2101 analysis of received signals based on detected errors and alarms: ES, SES, BBE, AS, UAS, and so on;
APS
APS (Automatic protection switching): Independently select start and complete trigger;
All SDH/SONET alarms and errors, Bit error, errors with threshold;
Number of switchovers indicated by APS protocol;
K1/K2 bytes set and displayed;
Display and save APS time, frequency, pass/fail, minimum/maximum/ average value.
APS time resolution: 1us; Propagation
Delay Measurement
Resolution: 0.1us;
Measurement max time: 2.0 s.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
PDH and DSn
PDH and DSn Test
Port PDH: E1, E3, E4; 1 Port; DSn: DS1, DS3;1 Port;
Measurement Out-of-service Mode; In-service Mode;
General
E1: complies with latest version ITU-T G.703 for 2048kbps;
DS1: complies with latest version ANSI T1.102 for 1544kbps;
E3: complies with latest version ITU-T G.703 for 34368kbps;
DS3: complies with latest version ANSI for 44736kbps;
E4: complies with latest version ITU-T G.703 for 139264kbps;
Impedance E1: 75Ω(unbalanced); E3: 75 Ω; DS3: 75 Ω; E4: 75 Ω;
Line Code E1: HDB3, AMI; DS1: B8ZS, AMI; E3: HDB3; DS3: B3ZS; E4: CMI;
Frame E1: unframed, PCM30, PCM31,
PCM30CRC, PCM31CRC;
DS1: unframed, SF-D4, ESF;
E3: unframed, framed (G.751);
DS3: unframed, framed;
E4: unframed, framed (G.751);
Transmitter Clock
Internal clock: Accuracy: 4.6ppm, up to 2ppm;
Clock Offset: ±100ppm (1ppm steps);
Recovered clock;
TTL level external 2.048MHz clock;
E1: 2.048Mbps; DS1: 1.544Mbps;
Receive Single Rate
±100ppm;
Frequency deviation indication resolution: ±1ppm; Impedance
Mode E1: terminate, monitor;
DS1: terminate, monitor;
E3: terminate, monitor;
DS3: terminate, monitor; E4: terminate;
Alarm
Alarm can to be detected and generated: E1: LOS, LOF, OOF, RAI, AIS, CRCLOFM,
MFASOOF, LOFMFAS, MFASRAI, LSS;
DS1: LOS, LOF, OOF, RAI, AIS, LSS;
E3: LOS, LOF, AIS, RDI;
DS3: LOS, LOF, AIS, RAI, LSS, IDLE;
E4: LOS, LOF, AIS, RAI, LSS;
Alarm generation mode: Continuous; Alternate; Burst;
Error
Error can be detected and generated: E1: FAS, CRC4, E-BIT, Code, BIT;
DS1: FAS, Code, BIT, CRC6;
E3: FAS, BIT;
DS3: FAS, C-BIT, P-BIT, FEBE, BIT;
E4: FAS, BIT;
Error generation mode: Single; Continuous; Alternate; Burst; Rate; N-frame;
BERT Pattern
Pattern generation and monitor for O.181 bulk test pattern;
Support to generate and detect: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31;
Support reversed PRBS pattern: 16bit user define pattern;
PDH and DSn Result
Status Display information of current status: Alarms and errors; Actual bit rate; Frequency deviation.
Statistics Event log display:
Alarms (seconds); Errors (count and rate); Start/stop time;
All events refresh with 1 second resolution;
Histogram All alarms and errors detected can be display in histogram;
Error Performance
G.821/G.826/M.2100 analysis of received signals based on detected errors and alarms: ES, SES, BBE,AS,UAS, and so on;
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
PDH and DSn Result
APS
APS(Automatic Protection Switching): Independently select start and complete trigger;
All PDH/DSn alarms and errors, Bit error, errors with threshold;
Number of switchovers indicated by APS protocol;
Display and save APS time, frequency, pass/fail, minimum/maximum/ average value.
APS time resolution: 1us; Propagation
Delay Measurement
Resolution: 0.1us;
Measurement max time: 2.0 s.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
OTP6200 + OTM2515 Ordering Information
OTP6200+OTM2515 STANDARD CONFIGURAIOTN
Module Description
OTP6200 Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules;
OTM2515
DS1 to STM-1/OC-3 PDH/SDH test module;
A couple BNC electrical interface for DS1/DS3, E1/E3/E4/STM-1 rates test;
SFP port for STM-1 and OC-3 SDH/SONET test;
SMA port for external clock port, support 1.544Mbps, 2.048MHz and 2.048Mbps;
PDH/SDH, DSn/SONET BER test;
Alarm generation and monitoring, error injection and monitoring;
APS and SDT test;
PDH/SDH performance test according with G.821, G.826, G.828, G.829, M.2100, M.2101;
SDH/SONET signal auto detection;
SDH/OTN through mode, can insert alarm and errors when use through mode;
SDH tributary scan;
Propagation delay test;
Remote control by PC;
Accessories Code Accessories Description
16080010 LC/PC to LC/PC full-duplex single-mode fibre, 3 meter, one;
16060090 75ohm BNC cables, 2m, two;
14020090 1.25G 1310nm 15Km LC SFP optical module, one;
05020050 SFP optical port dust proof cap - black - rubber, one;
05020060 RJ45 electrical port dust proof cap - black - rubber, one;
16060010 3 pins adapter cable, one;
43170020 OTP6200 100-240V input and 19V output AC/DC power adapter, one;
18080010 OTP6200 disc include user manual and OPWILL remote control software, one;
19070010 OTP6200 package, one;
18010010 Factory test report, one;
18010020 Calibration certificate, one;
18040011 One year warranty service;
OTM2515 OPTIONAL CONFIGURATION
SDH Optional Software
OPAP-OHSeqCapture 256 frames SDH overhead capture and decode capability;
OPAP-TCM SDH N1 and N2 bytes for tandem connection monitoring capability;
Optional Hardware
43160031 OTP6200 lithium polymer rechargeable battery;
OPAP-Twowarranty Two years extended warranty service;
14020160 1.25G-850nm-550m-MM-LC-SFP-DDM;
14020090 1.25G-1310nm-15km-SM-LC-SFP-DDM;
14020340 1.25G-1550nm-40km-SM-LC-SFP-DDM.
Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Www.OPWILL.com OPTIMISE THE TEST AS YOUR WILL
OTP6200 + OTM2516 Ordering Information
OTP6200+OTM2516 STANDARD CONFIGURAIOTN
Module Description
OTP6200 Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules;
OTM2516
DS1 to STM-4/OC-12 PDH/SDH test module;
A couple BNC electrical interface for DS1/DS3, E1/E3/E4/STM-1 rates test;
SFP port for STM-1/4 and OC-3/12 SDH/SONET test;
SMA port for external clock port, support 1.544Mbps, 2.048MHz and 2.048Mbps;
PDH/SDH, DSn/SONET BER test;
Alarm generation and monitoring, error injection and monitoring;
APS and SDT test;
PDH/SDH performance test according with G.821, G.826, G.828, G.829, M.2100, M.2101;
SDH/SONET signal auto detection;
SDH/OTN through mode, can insert alarm and errors when use through mode;
SDH tributary scan;
Propagation delay test;
Remote control by PC;
Accessories Code Accessories Description
16080010 LC/PC to LC/PC full-duplex single-mode fibre, 3 meter, one;
16060090 75ohm BNC cables, 2m, two;
14020090 1.25G 1310nm 15Km LC SFP optical module, one;
05020050 SFP optical port dust proof cap - black - rubber, one;
05020060 RJ45 electrical port dust proof cap - black - rubber, one;
16060010 3 pins adapter cable, one;
43170020 OTP6200 100-240V input and 19V output AC/DC power adapter, one;
18080010 OTP6200 disc include user manual and OPWILL remote control software, one;
19070010 OTP6200 package, one;
18010010 Factory test report, one;
18010020 Calibration certificate, one;
18040011 One year warranty service;
OTM2516 OPTIONAL CONFIGURATION
SDH Optional Software
OPAP-OHSeqCapture 256 frames SDH overhead capture and decode capability;
OPAP-TCM SDH N1 and N2 bytes for tandem connection monitoring capability;
Optional Hardware
43160031 OTP6200 lithium polymer rechargeable battery;
OPAP-Twowarranty Two years extended warranty service;
14020160 1.25G-850nm-550m-MM-LC-SFP-DDM;
14020090 1.25G-1310nm-15km-SM-LC-SFP-DDM;
14020340 1.25G-1550nm-40km-SM-LC-SFP-DDM.
Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales.
OTM2515/16/17 155M/622M/2.5G SDH/SONET Test Module
Copyright © OPWILL Technologies (Beijing) Co., Ltd. 2011-2018. All Rights Reserved.
OPWILL TECHNOLOGIES (BEIJING) CO., LTD.
Add: Room 415, Digital Media Building, No.7 Shangdi Information Road, Haidian District, Beijing, PRC. 100085
Tel: +86(10)8277-1386/2866/3382
Fax: +86(10)8277-1782
Please visit our website for the further information: www. OPWILL.com
OTP6200 + OTM2517 Ordering Information
OTP6200+OTM2517 STANDARD CONFIGURAIOTN
Module Description
OTP6200 Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules;
OTM2517
DS1 to STM-16/OC-48 PDH/SDH test module;
A couple BNC electrical interface for DS1/DS3, E1/E3/E4/STM-1 rates test;
SFP port for STM-1/4/16 and OC-3/12/48 SDH/SONET test;
SMA port for external clock port, support 1.544Mbps, 2.048MHz and 2.048Mbps;
PDH/SDH, DSn/SONET BER test;
Alarm generation and monitoring, error injection and monitoring;
APS and SDT test;
PDH/SDH performance test according with G.821, G.826, G.828, G.829, M.2100, M.2101;
SDH/SONET signal auto detection;
SDH/OTN through mode, can insert alarm and errors when use through mode;
SDH tributary scan;
Propagation delay test;
Remote control by PC;
Accessories Code Accessories Description
16080010 LC/PC to LC/PC full-duplex single-mode fibre, 3 meter, one;
16060090 75ohm BNC cables, 2m, two;
14020350 2.5G 1310nm 15km LC SFP optical module, one;
16060010 3 pins adapter cable, one;
43170020 OTP6200 100-240V input and 19V output AC/DC power adapter, one;
18080010 OTP6200 disc include user manual and OPWILL remote control software, one;
19070010 OTP6200 package, one;
18010010 Factory test report, one;
18010020 Calibration certificate, one;
18040011 One year warranty service;
OTM2517 OPTIONAL CONFIGURATION
SDH Optional Software
OPAP-OHSeqCapture 256 frames SDH overhead capture and decode capability;
OPAP-TCM SDH N1 and N2 bytes for tandem connection monitoring capability;
Optional Hardware
43160031 OTP6200 lithium polymer rechargeable battery;
OPAP-Twowarranty Two years extended warranty service;
14020380 2.5G-1550nm-40km-SM-LC-SFP-DDM.
Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales.