Embed Size (px)
Citation preview
DSEGenset
DSE4510/20AUTO START AND AUTO MAINS FAILURECONTROL MODULES
PC
The DSE4510 Auto Start ControlModule and the DSE4520 AutoMains (Utility) Failure ControlModule are suitable for a widevariety of single gen-setapplications.
Whilst maintaining functionsincluded within higher endcontrollers, such as generator orload power monitoring, theDSE45xx range of especiallycompact controllers provide theuser with the ultimate size tofeature ratio.
Monitoring engine speed, oilpressure, coolant temperature,frequency, voltage, current, powerand fuel level, the modules will givecomprehensive engine andalternator protection. This will beindicated on the largest back-litLCD icon display in its class via anarray of warning, electrical trip andshutdown alarms.
Electronic J1939 (CAN) and non-electronic (alternator sensing)engine support for diesel, gas andpetrol engines all in one variant.With a number of flexible inputs,outputs and protections, themodule can be easily adapted tosuit a wide range of applications.
Through USB Communication bothmodules can be easily configuredusing the DSE Configuration SuitePC Software or can be fullyconfigured through the module'sfront panel editor.
All DSE products are supported bythe DSE global tech nical supportteam which gives our customersand end users access to 24 hoursystem help and advice.
4
ISSUE 1
USBPORT
DC OUTPUT(2 for DSE4510)
CONFIGURABLEINPUTS
DC POWER SUPPLY
11 1ph2ph3ph
1ph2ph3phN
COMPREHENSIVE FEATURE LIST TO SUIT A WIDE VARIETY OF GEN-SET APPLICATIONS
7
OTHER
DSE4510/20
MAINS (UTILITY)SENSING(DSE4520)
GENERATORSENSING
CHARGEALTERNATOR
FUEL AND STARTOUTPUTS(Flexible with CAN)
ELECTRONICENGINE CAN
ANALOGUE SENDERS
ENVIRONMENTAL TESTING STANDARDS
ELECTRO-MAGNETIC COMPATIBILITYBS EN 61000-6-2EMC Generic Immunity Standard for the Industrial EnvironmentBS EN 61000-6-4EMC Generic Emission Standard for the Industrial Environment
ELECTRICAL SAFETYBS EN 60950Safety of Information Technology Equipment, including Electrical Business Equipment
TEMPERATUREBS EN 60068-2-1Ab/Ae Cold Test -30 oCBS EN 60068-2-2Bb/Be Dry Heat +70 oC
VIBRATIONBS EN 60068-2-6Ten sweeps in each of three major axes5 Hz to 8 Hz at +/-7.5 mm, 8 Hz to 500 Hz at 2 GN
HUMIDITYBS EN 60068-2-30Db Damp Heat Cyclic 20/55 oCat 95% RH 48 HoursBS EN 60068-2-78Cab Damp Heat Static 40 oCat 93% RH 48 Hours
SHOCKBS EN 60068-2-27Three shocks in each of three major axes15 GN in 11 mS
DEGREES OF PROTECTIONPROVIDED BY ENCLOSURESBS EN 60529IP65 - Front of module when installed into thecontrol panel with the optional sealing gasket.
34
+ +VOLTS
+
+
1ph2ph3phN
VOLTS D +W/L
DEUTZISUZUPERKINSCATERPILLARMTUVOLVOCUMMINSSCANIA
4510-03
4510-04
4520-03
4520-04
Auto start with real time clock
Auto start with real time clock &heated display
Auto Mains Failure with real timeclock
Auto Mains Failure with real timeclock & heated display
*AVAILABLE VARIANTS
DC OUTPUT4520 1 OF 4
DC OUTPUT4510 1 OF 24520 1 OF 4
GENERATOR /LOAD CURRENT
®
DSEGenset
DEEP SEA ELECTRONICS PLC UKHighfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PHTELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303EMAIL [email protected] WEBSITE www.deepseaplc.com
DEEP SEA ELECTRONICS INC USA3230 Williams Avenue, Rockford, IL 61101-2668 USATELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708EMAIL [email protected] WEBSITE www.deepseausa.com
Registered in England & Wales No.01319649VAT No.316923457
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to changethe details shown on this data sheet without prior notice. The contents are intended for guidance only.
055-132/09/12 (6) US
SPECIFICATION
DC SUPPLYCONTINUOUS VOLTAGE RATING8 V to 35 V Continuous
CRANKING DROPOUTSAble to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries.LEDs and backlight will not be maintained during cranking.
MAXIMUM OPERATING CURRENT85 mA at 12 V, 96 mA at 24 V
MAXIMUM STANDBY CURRENT51 mA at 12 V, 47 mA at 24 V
MAXIMUM SLEEP CURRENT35 mA at 12 V, 32 mA at 24 V
MAXIMUM DEEP SLEEP CURRENT<10 uA at 12 V, <10 uA at 24 V
MAINS (UTILITY) DSE4520 ONLYVOLTAGE RANGE15 V to 415 V AC (Ph to N)26 V to 719 V AC (Ph to Ph)
FREQUENCY RANGE3.5 Hz to 75 Hz
OUTPUTSOUTPUT A (FUEL)10 A short term, 5 A continuous, at supply voltage
OUTPUT B (START)10 A short term, 5 A continuous, at supply voltage
AUXILIARY OUTPUTS C & D2 A DC at supply voltage
AUXILIARY OUTPUTS E & F DSE45202 A DC at supply voltage GENERATORVOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph)
FREQUENCY RANGE3.5 Hz to 75 Hz
DIMENSIONSOVERALL140 mm x 113 mm x 43 mm5.5’’ x 4.4” x 1.7”
PANEL CUT-OUT118 mm x 92 mm4.6’’ x 3.6”
MAXIMUM PANEL THICKNESS8 mm0.3”
STORAGE TEMPERATURE RANGE-40°C to +85°C
OPERATING TEMPERATURE RANGE-30°C to +70°C-40°C to +70°C (for heated display variant)
OPTIONAL PARTS
PART PART NUMBERIP65 Gasket 020-282
RELATED MATERIALSTITLE PART NO’SDSE4510/20 Installation Instructions 053-157DSE4510/20 Operator Manual 057-171DSE4510/20 Configuration Suite PC Manual 057-172
DSE4510/20AUTO START AND AUTO MAINS FAILURECONTROL MODULESFEATURES
DSE4510
DSE4520
KEY BENEFITS• Ultimate size to feature ratio • Automatically transfers betweenmains (utility) and generator(DSE4520 only)
• Hours counter provides accurateinformation for monitoring andmaintenance periods
• User-friendly set-up and buttonlayout for ease of use
• Multiple parameters aremonitored simultaneously
• The module can be configuredto suit a wide range ofapplications
• Compatible with a wide rangeof CAN engines, including tier 4engine support
• Licence-free PC software• IP65 rating (with optionalgasket) offers increasedresistance to water ingress
KEY FEATURES• Largest back-lit icon display inits class
• Heated display option• Real time clock providesaccurate event logging
• Fully configurable via the fasciaor PC using USBcommunication
• Extremely efficient power savemode
• 3 phase generator sensing• 3 phase mains (utility) sensing(DSE4520 only)
• Compatible with 600 V ph - phnominal systems
• Generator/load powermonitoring (kW, kV A, kV Ar, pf)
• Accumulated power monitoring(kW h, kVA h, kVAr h)
• Generator overload protection(kW)
• Generator/load currentmonitoring and protection
• Fuel and start outputs(configurable when using CAN)
• 4 configurable DC outputs (2 forDSE4510)
• 3 configurable analogue/digitalinputs
• 4 configurable digital inputs• Configurable staged loadingoutputs
• CAN and alternator speedsensing in one variant
• 3 engine maintainance alarms• Engine speed protection• Engine hours counter• Engine pre-heat• Engine run-time scheduler• Engine idle control for starting &stopping
• Battery voltage monitoring• Start on low battery voltage• Configurable remote start input• 1 alternative configuration• Comprehensive warning,electrical trip or shutdownprotection upon fault condition
• LCD alarm indication• Event log (50)
![EN 300 019-2-4 - V2.5.1 - Environmental Engineering (EE); … · 2018. 7. 3. · [9] IEC 60068-2-30 (08-2005): "Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic](https://img.dokumen.tips/doc/110x75/61037307a81f945e936b615c/en-300-019-2-4-v251-environmental-engineering-ee-2018-7-3-9-iec.jpg)
