DSE8610AUTO START LOAD SHARE MODULE

DSEGenset

®

The DSE8610 is an easy to usemulti-generator loadshare system,designed to synchronise up to 32generators including electronic andnon-electronic engines.

The DSE8610 monitors thegenerator and indicates operationalstatus and fault conditions,automatically starting or stoppingthe engine on load demand or faultcondition.

System alarms are annunciated onthe LCD screen (multiple languageoptions available), illuminated LEDand audible sounder.

The event log will record 250 eventsto facilitate easy maintenance. Anextensive number of fixed andflexible monitoring, metering andprotection features are included as well as comprehensivecommunication and systemexpansion options.

Using the DSE PC ConfigurationSuite Software allows easyalteration of the operationalsequences, timers and alarms. Withall communication ports capable ofbeing active at the same time, theDSE8610 is ideal for a wide varietyof demanding load shareapplications.

KEY LOAD SHARE FEATURES:• Peak lopping (with DSE8x60)• Sequential set start• Manual voltage/frequencyadjustment

• R.O.C.O.F. and vector shift• Generator load demand• Automatic hours run balancing• Mains (Utility) de-coupling• Mains (Utility) de-couplingtest mode

• Dead bus sensing• Bus failure detection• Direct governor and AVR control• Volts and frequency matching• kW and kV Ar load sharing• Dead bus synchronising

FEATURES

ENVIRONMENTAL TESTING STANDARDS

ELECTRO MAGNETIC COMPATIBILITYBS EN 61000-6-2EMC Generic Immunity Standard for theIndustrial EnvironmentBS EN 61000-6-4EMC Generic Emission Standard for theIndustrial Environment

ELECTRICAL SAFETYBS EN 60950Safety of Information Technology Equipment,including Electrical Business Equipment

TEMPERATUREBS EN 60068Ab/Ae Cold Test -30oCBS EN 60068-2-2Bb/Be Dry Heat +70oC

VIBRATIONBS EN 60068-2-6Ten sweeps in each of three major axes5Hz to 8Hz @ +/-7.5mm, 8Hz to 500Hz @ 2gn

HUMIDITYBS EN 60068-2-30Db Damp Heat Cyclic 20/55oC @ 95% RH 48 HoursBS EN 60068-2-78Cab Damp Heat Static 40oC @ 93% RH 48 Hours

SHOCKBS EN 60068-2-27Three shocks in each of three major axes15gn in 11mS

DEGREES OF PROTECTIONPROVIDED BY ENCLOSURESBS EN 60529IP65 - Front of module when installed into thecontrol panel with the supplied sealing gasket.

COMPREHENSIVE FEATURE LIST TO SUIT A WIDE VARIETYOF LOAD SHARE APPLICATIONS

1ph2ph3phN

DSE2130DSE2131DSE2133DSE2152DSE2157DSE2548

2 1ph2ph3phE

1ph2ph3phN

RS232 ANDRS485

DSENET®

EXPANSIONUSBPORT

USBHOST

CONFIGURABLEINPUTS

DC OUTPUTS ANALOGUESENDERS

EMERGENCY STOP

DC POWER SUPPLY 8-35V

DSE86107

OTHER

D +W/L

ETHERNET

11

232 485

6 4

PCMODBUSMODEM

BUSSENSING

VOLT FREEOUTPUTS

GENERATOR SENSING CHARGEALTERNATOR

ELECTRONIC ENGINES

MAGNETICPICK-UP

VOLTSCURRENT

+

+

ISSUE 3

MSC

55xx 75xx 8xxx

DEUTZISUZUPERKINSCATERPILLARMTUVOLVOCUMMINSSCANIA

FUEL & STARTOUTPUTS

DEEP SEA ELECTRONICS PLC UKHighfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PHTELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303EMAIL sales@deepseaplc.com WEBSITE www.deepseaplc.com

DEEP SEA ELECTRONICS INC USA3230 Williams Avenue, Rockford, IL 61101-2668 USATELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708EMAIL sales@deepseausa.com WEBSITE www.deepseausa.com

055-083/03/12 (5)

RELATED MATERIALSTITLE PART NO’SDSE8610 Installation Instructions 053-069DSE8610 Operator Manual 057-115DSE8600 PC Configuration Suite Manual 057-119DSE8660 Date Sheet 055-086

DSE8610AUTO START LOAD SHARE MODULE

®

DSEGenset

FEATURES

Registered in England & Wales No.01319649VAT No.316923457

Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to changethe details shown on this data sheet without prior notice. The contents are intended for guidance only.

SPECIFICATION

DC SUPPLYCONTINUOUS VOLTAGE RATING8 V to 35 V continuous

CRANKING DROPOUTSAble to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries

MAXIMUM OPERATING CURRENT460 mA at 12 V, 245 mA at 24 V

MAXIMUM STANDBY CURRENT375 mA at 12 V, 200 mA at 24 V

CHARGE FAIL/EXCITATION RANGE0 V to 35 V

OUTPUTSOUTPUT A (FUEL)15 A DC at supply voltage

OUTPUT B (START)15 A DC at supply voltage

OUTPUTS C & D8 A AC at 250 V AC (Volt free)

AUXILIARY OUTPUTS E,F,G,H,I & J2 A DC at supply voltage

GENERATOR & BUSVOLTAGE RANGE 15 V to 333 V AC (L-N)

FREQUENCY RANGE3.5 Hz to 75 Hz

MAGNETIC PICK-UPVOLTAGE RANGE+/- 0.5 V to 70 V

FREQUENCY RANGE10,000 Hz (max)

BUILT-IN GOVERNOR CONTROLMINIMUM LOAD IMPEDANCE 1000ΩFully isolated

GAIN VOLTAGE0 V to 10 V DCFully isolated

OFFSET VOLTAGE+/- 10 V DCFully isolated

BUILT-IN AVR CONTROLMINIMUM LOAD IMPEDANCE1000ΩFully isolated

GAIN VOLTAGE0 V to 10 V DCFully isolated

OFFSET VOLTAGE+/- 10 V DCFully isolated

DIMENSIONSOVERALL240 mm x 172 mm x 57 mm9.4” x 6.8” x 2.2”

PANEL CUTOUT220 mm x 160 mm8.7” x 6.3”

MAXIMUM PANEL THICKNESS8 mm0.3”

OPERATING TEMPERATURE RANGE-30 oC to +70 oC

STORAGE TEMPERATURE RANGE-40 oC to +85 oC

KEY FEATURES• Comprehensive synchronising &loadshare capabilities

• Built-in governor and AVRcontrol

• 4-Line back-lit LCD text display• Five key menu navigation• Front panel editing with PINprotection

• Customisable status screens• Power save mode• 11 configurable inputs• 8 configurable outputs• Flexible sender inputs• Configurable timers and alarms• 3 configurable maintenancealarms

• Multiple date and time scheduler• Configurable event log (250)• Tier 4 CAN engine support• Integral PLC editor• Easy access diagnostic page• CAN and Magnetic Pick-up/Alt.sensing

• Fuel usage monitor and low fuelalarms

• Charge alternator failure alarm• Manual fuel pump control • “Protections disabled” feature• kW & kV Ar overload protection• Reverse power (kW & kV Ar)

protection• LED and LCD alarm indication• Power monitoring (kW h, kV Ar,kV A h, kV Ar h)

• Load switching (load sheddingand dummy load outputs)

• Unbalanced load protection• Independent Earth Fault trip• USB connectivity• Backed up real time clock• Fully configurable via DSEConfiguration Suite PC software

• Configurable display languages• Remote SCADA monitoring viaDSE Configuration Suite PCsoftware

• User selectable RS232 andRS485 & Ethenetcommunications

• Modbus RTU/TCP• Configurable Gencomm pages• Advanced SMS messaging(additional external modemrequired)

• Start & stop capability via SMSmessaging

• Additional display screens tohelp with modem diagnostics

• DSENet® expansion compatible• Data logging and trending

KEY BENEFITS• Compatible with DSE55xx,DSE75xx & DSE8xxx series ofmodules

• 132 x 64 pixel ratio display forclarity

• Real-time clock providesaccurate event logging

• Multiple date and time scheduler• Set maintenance periods canbe configured to maintainoptimum engine performance

• Ethernet communications,provides advanced remotemonitoring at low cost

• Can be integrated into buildingmanagement systems (BMS)

• Increased input and outputexpansion capability via DSENet®

• Licence-free PC software• IP65 rating (with suppliedgasket) offers increasedresistance to water ingress

• PLC editor allows userconfigurable functions to meetspecific applicationrequirements