Upload
hoangmien
View
214
Download
0
Embed Size (px)
Citation preview
DS90Ux949EVM User's Guide
User's Guide
Literature Number: SNLU169December 2014
Contents
1 DS90Ux949EVM User's Guide ................................................................................................ 51.1 General Description ......................................................................................................... 51.2 Features....................................................................................................................... 51.3 System Requirements....................................................................................................... 61.4 Contents of the Demo Evaluation Kit ..................................................................................... 61.5 Applications Diagram........................................................................................................ 61.6 Typical Configuration ........................................................................................................ 71.7 Quick Start Guide ............................................................................................................ 81.8 Default Jumper Settings .................................................................................................... 91.9 Default Switch Settings ..................................................................................................... 91.10 Demo Board Connections................................................................................................. 101.11 ALP Software Setup ....................................................................................................... 13
1.11.1 System Requirements ........................................................................................... 131.11.2 Download Contents .............................................................................................. 131.11.3 Installation of the ALP Software ................................................................................ 131.11.4 Installation of the Device Profiles .............................................................................. 131.11.5 Startup - Software Description.................................................................................. 131.11.6 Information Tab................................................................................................... 151.11.7 HDMI Tab ......................................................................................................... 161.11.8 Pattern Generator Tab........................................................................................... 171.11.9 Registers Tab ..................................................................................................... 181.11.10 Registers Tab - Address 0x00 selected ..................................................................... 191.11.11 Registers Tab - Address 0x00 expanded.................................................................... 201.11.12 Scripting Tab .................................................................................................... 21
1.12 Troubleshooting ALP Software ........................................................................................... 221.12.1 ALP Loads the Incorrect Profile ................................................................................ 221.12.2 ALP does not detect the EVM .................................................................................. 24
1.13 Typical Connection and Test Equipment................................................................................ 261.14 Equipment References .................................................................................................... 271.15 Cable References .......................................................................................................... 27
2 Bill of Materials .................................................................................................................. 28A EVM PCB Schematics ......................................................................................................... 33B Board Layout ..................................................................................................................... 43Revision History.......................................................................................................................... 48
2 Contents SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
List of Figures1-1. Applications Diagram........................................................................................................ 61-2. Typical Configuration ........................................................................................................ 71-3. Interfacing to the EVM ...................................................................................................... 81-4. Launching ALP ............................................................................................................. 141-5. Initial ALP Screen .......................................................................................................... 141-6. Follow-up Screen........................................................................................................... 151-7. ALP Information Tab ....................................................................................................... 151-8. ALP HDMI Tab.............................................................................................................. 161-9. ALP Pattern Generator Tab............................................................................................... 171-10. ALP Registers Tab ......................................................................................................... 181-11. ALP Device ID Selected................................................................................................... 191-12. ALP Device ID Expanded ................................................................................................. 201-13. ALP Scripting Tab .......................................................................................................... 211-14. USB2ANY Setup ........................................................................................................... 221-15. Remove Incorrect Profile .................................................................................................. 221-16. Add Correct Profile ......................................................................................................... 231-17. Finish Setup................................................................................................................. 231-18. ALP No Devices Error ..................................................................................................... 241-19. Windows 7, ALP USB Driver ............................................................................................. 241-20. ALP in Demo Mode ........................................................................................................ 251-21. ALP Preferences Menu.................................................................................................... 251-22. Typical Test Setup for Video Application................................................................................ 261-23. Typical Test Setup for Evaluation ........................................................................................ 26
3SNLU169–December 2014 List of FiguresSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
List of Tables1-1. Default Board Jumper Settings ............................................................................................ 91-2. Default Board Switch Settings ............................................................................................. 91-3. Power Supply ............................................................................................................... 101-4. FPD-Link III Output Signals P1........................................................................................... 101-5. Alternative FPD-Link III Output Signals ................................................................................. 101-6. HDMI Input Signals ........................................................................................................ 101-7. USB2ANY Connector ...................................................................................................... 101-8. I2C/CCI Interface Header J20 ............................................................................................ 101-9. GPIO/Audio Interface ...................................................................................................... 111-10. SPI/D_GPIO Interface ..................................................................................................... 111-11. MODE_SEL[1:0] Settings ................................................................................................. 111-12. Configuration Select (MODE_SEL0) -- SW-DIP8 - S2 ................................................................ 111-13. Configuration Select (MODE_SEL1) - SW-DIP8 - S6 ................................................................. 121-14. IDx SW-DIP8 - S3 ......................................................................................................... 122-1. Bill of Materials ............................................................................................................. 28
4 List of Tables SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Chapter 1SNLU169–December 2014
DS90Ux949EVM User's Guide
1.1 General DescriptionThe DS90Ux949-Q1EVM (Evaluation Module) converts HDMI to FPD-Link III. This kit will demonstrate thefunctionality and operation of the DS90Ux949-Q1. The DS90Ux949-Q1 is an HDMI to FPD-Link IIISerializer which, in conjunction with the DS90Ux940-Q1/DS90Ux948-Q1 Deserializers, takes the datafrom HDMI serial stream and translates it into either single- or dual-lane FPD-Link III interface. TheDS90Ux949-Q1 supports video resolutions up to WUXGA and 1080p60 with 24-bit color depth.
The FPD-Link III interface supports video and audio data transmission and full duplex control, includingI2C and SPI communication, over the same differential link. In backward compatible mode, the devicesupports up to WXGA and 720p resolutions with 24-bit color depth over a single differential link.
The device supports up to 7.1 audio channels. Audio data received from the HDMI stream is encrypted,serialized, and sent out on the FPD-Link III stream to a compatible deserializer. Up to 8-channel I2Sinterface with maximum bit rate of 192 kHz.
The demo board is not intended for EMI testing. The demo board was designed for easy accessibility todevice pins with tap points for monitoring or applying signals, additional pads for termination, and multipleconnector options.
1.2 Features• Supports Pixel Clock Frequency up to 170 MHz for WUXGA (1920x1200) and 1080p60 resolutions
with 24-bit Color Depth• HDMI Receiver to accept HDMI as input• Dual FPD-Link III output interface
– Single Channel: Up to 96 MHz Pixel Clock– Dual Channel: Up to 170 MHz Pixel Clock
• Up to 15 meters over Single-Ended Coaxial or Differential Shielded Twisted-Pair (STP) cable• Backwards Compatible to DS90Ux926Q-Q1, DS90Ux928-Q1, DS90Ux940-Q1, and DS90Ux948-Q1
FPD-Link III Deserializers• @Speed BIST• Supports 7.1 multiple I2S (4 data) channels• Single +12V power supply for EVM• 1.8V LVCMOS I/O interface• 1.8V or 3.3V compatible LVCMOS I2C interface• Automotive grade product: AEC-Q100 Grade 2 qualified
5SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
FPD-Link III2 Lane
VDDIO(1.8V)
IDx
DOUT0+
DOUT0-
1.1V
IN_CLK-/+
HDMI
HPDDDCCEC
DOUT1+
DOUT1-
RIN0+
RIN0-
RIN1+
RIN1-
CLK1+/-
CLK2+/-
FPD-Link (Open LDI)
D0+/-
D1+/-
D2+/-
D3+/-
D4+/-
D5+/-
D6+/-
D7+/-
DS90Ux949-Q1
SerializerDS90Ux948-Q1
Deserializer
IDx
D_GPIO (SPI)
D_GPIO(SPI)
LVDS Display1080p60
or Graphic Processor
Mobile Device
or Graphics
Processor
IN_D0-/+
IN_D1-/+
IN_D2-/+
I2C
1.8V
VDDIO(3.3V / 1.8V)1.2V3.3V
I2C
System Requirements www.ti.com
1.3 System RequirementsIn order to demonstrate, the following is required:1. FPD-Link III compatible Deserializer
(a) DS90Ux940-Q1, DS90Ux948-Q1 up to 1080p60(b) DS90Ux926Q-Q1, DS90Ux928-Q1 up to 720p60
2. HDMI source3. Optional I2C controller4. Power supply for 12V @ 1A (required)
1.4 Contents of the Demo Evaluation Kit1. One EVM board with the DS90Ux949-Q1
1.5 Applications Diagram
Figure 1-1. Applications Diagram
6 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
DS90Ux949
FPD-Link III Deserializer
Video Processor
Video Processor Board
Cluster, Head Unit
Dual FPD-LINK III
Display
(Video Data + Ctrl + PCLK)
(I2C)
(I2C)
(OpenLDI)
www.ti.com Typical Configuration
1.6 Typical Configuration
Figure 1-2. Typical Configuration
Figure 1-1 and Figure 1-2 illustrate the use of the chipset in a display application.
7SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
DDCVDD_DDC
DDC_SCL
DDC_SDA
GND
APPLY
EXTERNAL
12V HERE
GND
1.8V
GND
3.3V
GND
1.1V
I2C extVDD_I2C
SCL
SDA
GND
APPLY
HDMI
INPUT
HERE
DOUT0+
DOUT0-
*DOUT1+
*DOUT1-
PDB
MomentaryPDB=L
PDB=H
VD
D_
DD
CV
TE
RM
c
I2C
1.8
V
1.8
V
3.3
VR
x_
5V
3.3
V
3.3
V
IDx
0x
20
0x
1C
0x
18
MODE_SEL1MODE_SEL0
KvoÇ�í��Á]��Z�^KE_�������]u� KvoÇ�í��Á]��Z�^KE_�������]u�KvoÇ�í��Á]��Z�^KE_�������]u�
1
MSP430
(USB2ANY)
Connect to PC
for I2C register access
* Not populated
on 929 EVM
DS90Ux949
12
V
(5)
(4)
(3)
(2)
*
*
0x
24
0x
2C
0x
28
0x
34
0x
30
2345678 12345678
(1)
Quick Start Guide www.ti.com
1.7 Quick Start Guide1. Configure switches S2, S3, and S6 to set device’s operating modes
• S2: MODE_SEL0 = 1 (default factory setting)• S3: IDx = 0x18 (default factory setting)• S6: MODE_SEL1 = 1 (default factory setting)
2. Connect P1 (DOUT[1:0]+/-) to compatible Deserializer e.g. DS90Ux940-Q1/DS90Ux948-Q1 using STPcable (default)
3. Connect J36 to 12V.(a) Optional power options available (see Table 1-3)
4. Plug in HDMI source5. Connect J29 with miniUSB (5-pin_ to USB A (4-pin) cable to PC USB port
For details of pin-names and pin-functions, please refer to the DS90Ux949Q datasheet.
Figure 1-3. Interfacing to the EVM
8 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Default Jumper Settings
1.8 Default Jumper SettingsEnsure that the board has the default board jumper settings:
Table 1-1. Default Board Jumper Settings
Jumper Jumper SettingsJ3 Connect 2 and 3J14 Connect 2 and 3J17 Connect 1 and 2J18 Connect 2 and 3J22 Connect 1 and 2J33 Connect 1 and 2J37 Connect 2 and 3J40 Connect 2 and 3J41 Connect 2 and 3
1.9 Default Switch SettingsEnsure that the board has the default board switch settings:
Table 1-2. Default Board Switch Settings
Switch Switch SettingsS1 1 to 3 ONS2 1 ON, 2 to 8 OFFS3 1 ON, 2 to 8 OFFS5 All OFFS6 1 ON, 2 to 8 OFF
9SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Demo Board Connections www.ti.com
1.10 Demo Board Connections
Table 1-3. Power Supply
Designator Signal Description12V ±5% Main Power, Single +12V power connector that suppliesJ36 +12V power to the entire board.
J35.1 (Optional) +1.1V 1.1V ±5%, Alternative to Main Power. If used, remove R195.J39.1 (Optional) +1.8V 1.8V ±5%, Alternative to Main Power. If used, remove R204.J42.1 (Optional) +3.3V 3.3V ±5%, Alternative to Main Power. If used, remove R207.J33.2 (Optional) +5V 5V ±5%, Alternative to Main Power.
Table 1-4. FPD-Link III Output Signals P1
Designator Port SignalP1.1 DOUT0-
FPD-Link III Port 0P1.3 DOUT0+P1.2 DOUT1-
FPD-Link III Port 1P1.4 DOUT1+
Table 1-5. Alternative FPD-Link III Output Signals
Designator Port SignalJ11 DOUT0-
FPD-Link III Port 0J9 DOUT0+J13 DOUT1-
FPD-Link III Port 1J12 DOUT1+
Table 1-6. HDMI Input Signals
Designator Signal DescriptionJ10.12 IN_CLK- HDMI TMDS clock inputJ10.10 IN_CLK+J10.9 IN_D0- HDMI TMDS data0 inputJ10.7 IN_D0+J10.6 IN_D1- HDMI TMDS data1 inputJ10.4 IN_D1+J10.3 IN_D2- HDMI TMDS data2 inputJ10.1 IN_D2+
Table 1-7. USB2ANY Connector
Designator DescriptionJ29 mini USB 5 pin
Table 1-8. I2C/CCI Interface Header J20
Designator SignalJ20.1 VDDI2CJ20.2 SCLJ20.3 SDAJ20.4 GND
10 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Demo Board Connections
Table 1-9. GPIO/Audio Interface
Designator Signal DescriptionJ21.18 SDIN/GPIO0 Aux I2S Data Input / Remote or Local I/OJ21.20 SWC/GPIO1 Aux I2S Word Clock Output / Remote or Local I/OJ21.2 I2S_DC/GPIO2 I2S Data Input / Remote or Local I/OJ21.4 I2S_DD/GPIO3 I2S Data Input / Remote or Local I/OJ21.6 VDDIO GPIO Voltage Level 1.8V
I2S_DB/GPIO5_REJ21.8 I2S Data Input / Local only I/OGI2S_DA/GPIO6_REJ21.10 I2S Data Input / Local only I/OGI2S_WC/GPIO7_REJ21.12 I2S Word Clock Input / Local only I/OGI2S_CLK/GPIO8_REJ21.14 I2S Clock Input / Local only I/OG
J21.24 MCLK I2S System Clock Output
Table 1-10. SPI/D_GPIO Interface
Designator Signal DescriptionJ21.6 VDDIO GPIO Voltage Level 1.8VJ21.32 D_GPIO3/SS I/O in Dual FPD-Link III mode / Slave SelectJ21.30 D_GPIO2/SCLK I/O in Dual FPD-Link III mode / Serial ClockJ21.28 D_GPIO1/MISO I/O in Dual FPD-Link III mode / Master In, Slave OutJ21.26 D_GPIO0/MOSI I/O in Dual FPD-Link III mode / Master Out, Slave In
Configuration of the device may be done via the MODE_SEL[1:0]. These modes are latched into registerlocation during power-up:
Table 1-11. MODE_SEL[1:0] Settings
Mode Setting FunctionLook for remote EDID, if none found, use internal SRAM EDID. Can be
0 overridden from register. Remote EDID address may be overridden fromEDID_SEL: Display ID Select default 0xA0.
1 Use external local EDID.0 Disable.
AUTO-SS: Auto Sleep-State1 Enable.0 HDMI audio.AUX_I2S: AUX Audio
Channel 1 HDMI + AUX audio channel.0 Internal HDCP/HDMI control.EXT_CTL: External Controller
Override 1 External HDCP/HDMI control from I2C interface pins.0 Enable FPD-Link III for twisted pair cabling.
COAX: Cable Type1 Enable FPD-Link III for coaxial cabling.0 Use internal SRAM EDID.REM_EDID_LOAD: Remote
EDID Load 1 If available, remote EDID is copied into internal SRAM EDID.
Table 1-12. Configuration Select (MODE_SEL0) -- SW-DIP8 - S2 (1)
MODE # EDID_SEL AUTO_SS AUX_I2S1 0 0 02 0 0 1
(1) Only set one high.
11SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Demo Board Connections www.ti.com
Table 1-12. Configuration Select (MODE_SEL0) -- SW-DIP8 - S2 (1) (continued)MODE # EDID_SEL AUTO_SS AUX_I2S
3 0 1 04 0 1 15 1 0 06 1 0 17 1 1 08 1 1 1
Table 1-13. Configuration Select (MODE_SEL1) - SW-DIP8 - S6 (1)
MODE # EXT_CTL COAX REM_EDID_LOAD1 0 0 02 0 0 13 0 1 04 0 1 15 1 0 06 1 0 17 1 1 08 1 1 1
(1) Only set one high.
The strapped values can be viewed and/or modified in the following locations:• EDID_SEL : Latched into BRIDGE_CTL[0], EDID_DISABLE (0x4F[0]).• AUTO_SS : Latched into Register 0x1[7], SOFT_SLEEP.• AUX_I2S : Latched into BRIDGE_CFG[1], AUDIO_MODE[1] (0x54[1]).• EXT_CTL: Latched into BRIDGE_CFG[7], EXT_CONTROL (0x54[7]).• COAX : Latched into DUAL_CTL1[7], COAX_MODE (0x5B[7]).• REM_EDID_LOAD : Latched into BRIDGE_CFG[5] (0x54[5]).
Table 1-14. IDx SW-DIP8 - S3 (1)
Designator 7-Bit Address 8-Bit AddressS1.1 (Default) 0x0C 0x18
S1.2 0x0E 0x1CS1.3 0x10 0x20S1.4 0x12 0x24S1.5 0x14 0x28S1.6 0x16 0x2CS1.7 0x18 0x30S1.8 0x1A 0x34
(1) Only set one high.
12 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1 3 42 A 1 2 3 4 MINI
www.ti.com ALP Software Setup
1.11 ALP Software Setup
1.11.1 System Requirements
Operating System: Windows 7 64-bitUSB: USB2ANYUSB2ANY Firmware Version: 2.5.2.0
1.11.2 Download ContentsTI Analog LaunchPAD can be downloaded from: http://www.ti.com/tool/alp.
Download and extract the “snlc048.zip” file to a temporary location that can be deleted later.
Make sure J29 on the DS90Ux949 is connected to a PC USB port with USB cable and power is applied tothe DS90Ux949 EVM.
The following installation instructions are for the Windows 7 64-bit Operating System.
1.11.3 Installation of the ALP SoftwareExecute the ALP Setup Wizard program called “ALPF_setup_v_x_x_x.exe” that was extracted to atemporary location on the local drive of your PC.
There are 7 steps to the installation once the setup wizard is started:1. Select the "Next" button.2. Select “I accept the agreement” and then select the “Next” button.3. Select the location to install the ALP software and then select the “Next” button.4. Select the location for the start menu shortcut and then select the “Next” button.5. There will then be a screen that allows the creation of a desktop icon. After selecting the desired
choices select the “Next” button.6. Select the “Install” button, and the software will then be installed to the selected location.7. Uncheck “Launch Analog LaunchPAD” and select the “Finish” button. The ALP software will start if
“Launch Analog LaunchPAD” is checked, but it will not be useful until the USB driver is installed andboard is attached.
Connect J29 USB jack of the DS90Ux949Q EVM board to a PC/laptop USB port using a Type A
to mini-B USB cable. Power the DS90Ux949Q EVB board with a 12 VDCpower supply. The “Found New Hardware Wizard” will open on the PC/laptop.
1.11.4 Installation of the Device ProfilesThere are 2 steps to add the DS90Ux949 profile:1. Contact TI for the DS90Ux949 profile2. Extract the “DS90Ux949.zip” to ALP’s profile folder. The profile folder can be found at: C:\Program
Files (x64)\Texas Instruments\Analog LaunchPAD vx.x.x\Profiles\
1.11.5 Startup - Software DescriptionMake sure all the software has been installed and the hardware is powered on and connected to the PC.Execute “Analog LaunchPAD” shortcut from the start menu. The default start menu location is under AllPrograms > Texas Instruments > Analog LaunchPAD vx.x.x > Analog LaunchPAD to start MainGUI.exe.
13SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
ALP Software Setup www.ti.com
Figure 1-4. Launching ALP
The application should come up in the state shown in the figure below. If it does not, see Section 1.12,“Troubleshooting ALP Software”.
Under the Devices tab click on “DS90Ux949” to select the device and open up the device profile and itsassociated tabs.
Figure 1-5. Initial ALP Screen
After selecting the DS90Ux949, the following screen should appear.
14 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com ALP Software Setup
Figure 1-6. Follow-up Screen
1.11.6 Information TabThe Information tab is shown below. Please note the device revision could be different.
Figure 1-7. ALP Information Tab
15SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
ALP Software Setup www.ti.com
1.11.7 HDMI TabThe HDMI tab is shown below.
Figure 1-8. ALP HDMI Tab
16 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com ALP Software Setup
1.11.8 Pattern Generator TabThe SER Pattern Generator tab is shown below.
Figure 1-9. ALP Pattern Generator Tab
17SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
ALP Software Setup www.ti.com
1.11.9 Registers TabThe Registers tab is shown below.
Figure 1-10. ALP Registers Tab
18 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com ALP Software Setup
1.11.10 Registers Tab - Address 0x00 selected
Address 0x00 selected as shown below. Note that the “Value:” box, , will now show the hexvalue of that register.
Figure 1-11. ALP Device ID Selected
19SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
ALP Software Setup www.ti.com
1.11.11 Registers Tab - Address 0x00 expandedBy double clicking on the Address bar
or a single click on . Address 0x00 expanded reveals contents by bits. Any register address displayedcan be expanded.
Figure 1-12. ALP Device ID Expanded
Any RW Type register, , can be written into by writing the hex value into the “Value:” box,or putting the pointer into the individual register bit(s) box by a left mouse click to put a check mark(indicating a “1”) or unchecking to remove the check mark (indicating a “0”). Click the “Apply” button towrite to the register, and “refresh” to see the new value of the selected (highlighted) register.
The box toggles on every mouse click.
20 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com ALP Software Setup
1.11.12 Scripting TabThe Scripting tab is shown below.
Figure 1-13. ALP Scripting Tab
The script window provides a full Python scripting environment which can be for running scripts andinteracting with the device in an interactive or automated fashion.
WARNINGDirectly interacting with devices either through registermodifications or calling device support library functions can effectthe performance and/or functionality of the user interface and mayeven crash the ALP Framework application.
21SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Troubleshooting ALP Software www.ti.com
1.12 Troubleshooting ALP Software
1.12.1 ALP Loads the Incorrect ProfileIf ALP opens with the incorrect profile loaded the correct profile can be loaded from theUSB2ANY/Aardvark Setup found under the tools menu.
Figure 1-14. USB2ANY Setup
Highlight the incorrect profile in the Defined ALP Devices list and press the remove button.
Figure 1-15. Remove Incorrect Profile
Find the correct profile under the Select a Daughter Board list, highlight the profile and press Add.
22 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Troubleshooting ALP Software
Figure 1-16. Add Correct Profile
Select Ok and the correct profile should now be loaded.
Figure 1-17. Finish Setup
23SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Troubleshooting ALP Software www.ti.com
1.12.2 ALP does not detect the EVMIf the following window opens after starting the ALP software, double check the hardware setup.
Figure 1-18. ALP No Devices Error
It may also be that the USB driver is not installed. Check the device manager. There should be a “HID-compliant device” under the “Human Interface Devices” as shown below.
Figure 1-19. Windows 7, ALP USB Driver
The software should start with only “DS90UH947” in the “Devices” pull down menu. If there are moredevices then the software is most likely in demo mode. When the ALP is operating in demo mode there isa “(Demo Mode)” indication in the lower left of the application status bar as shown below.
24 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Troubleshooting ALP Software
Figure 1-20. ALP in Demo Mode
Disable the demo mode by selecting the “Preferences” pull down menu and un-checking “Enable DemoMode”.
Figure 1-21. ALP Preferences Menu
After demo mode is disabled, the ALP software will poll the ALP hardware. The ALP software will updateand have only “DS90UH947” under the “Devices” pull down menu.
25SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
DIGITAL VIDEO GENERATOR
DIGITAL
VIDEO
GENERATOR
Digital Video Source
OpenLDI LVDS
HDMI/DP++
or
OpenLDI
Contents of Demo KitLogic Analyzer / Oscilloscope
DS90Ux949
EVM Board
Deserializer
Board
FPD-Link III
Display
HDMI/DP++or
OpenLDIGenerator
OpenLDILVDS
DS90Ux949EVM Board
Deserializer Board
FPD-Link III
Contents of Demo Kit
Graphics Controller / Video Processor Board
Typical Connection and Test Equipment www.ti.com
1.13 Typical Connection and Test EquipmentThe following is a list of typical test equipment that may be used to generate signals for the Serializerinputs:1. Digital Video Source – for generation of specific display timing such as Digital Video Processor or
Graphics Controller (GPU) with HDMI or OpenLDI output.2. Any other signal generator / video source - This video generator may be used for video signal sources
for DVI or DP++3. Any other signal / video generator that provides the correct input levels as specified in the datasheet.
The picture below shows a typical test set up using a Graphics Controller and display.
Figure 1-22. Typical Test Setup for Video Application
The picture below shows a typical test set up using a video generator and logic analyzer.
Figure 1-23. Typical Test Setup for Evaluation
26 DS90Ux949EVM User's Guide SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Equipment References
1.14 Equipment References
NOTE: Please note that the following references are supplied only as a courtesy to our valuedcustomers. It is not intended to be an endorsement of any particular equipment or supplier.
Digital Video Pattern Generator:Astrodesign
www.astro-americas.com
Logic Analyzer:keysight Technologies
www.keysight.com
Corelis CAS-1000-I2C/E I2C Bus Analyzer and Exerciser Products:www.corelis.com/products/I2C-Analyzer.htm
Aardvark I2C/SPI Host Adapter Part Number: TP240141www.totalphase.com/products/aardvark_i2cspi
1.15 Cable ReferencesFor optimal performance, we recommend Shielded Twisted Pair (STP) 100ohm differential impedance and24 AWG (or larger diameter) cable for high-speed data applications.
Leoni Dacar 538 series cable:www.leoni-automotive-cables.com
Rosenberger HSD connector:www.rosenberger.de/en/Products/35_Automotive_HSD.php
27SNLU169–December 2014 DS90Ux949EVM User's GuideSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Chapter 2SNLU169–December 2014
Bill of Materials
Table 2-1. Bill of Materials
Designator Description Part Number Manufacturer Package QtyReference
PCB1 Printed Circuit Board SV600978 Any 1C1, C9, C128 CAP, CERM, 0.01 µF, 100 06031C103JAT2A AVX 0603 3
V, +/- 5%, X7R, 0603C2, C5, C6, C10, C11, C13, CAP, CERM, 10 µF, 10 V, GRM21BR71A106KE51L MuRata 0805 13C83, C93, C106, C116, C123, +/- 10%, X7R, 0805C133, C137C3, C7, C12, C14, C81, C82, CAP, CERM, 0.1 µF, 16 V, GRM155R71C104KA88D MuRata 0402 30C84, C85, C89, C94, C95, +/- 10%, X7R, 0402C96, C97, C98, C104, C105,C107, C108, C110, C111,C113, C117, C121, C122,C126, C129, C131, C132,C135, C136C4, C8 CAP, TA, 1 µF, 16 V, +/- 293D105X9016A2TE3 Vishay- 3216-18 2
10%, 9.3 ohm, SMD SpragueC15, C25, C32, C39, C50, CAP, CERM, 4.7 µF, 16 V, GRM21BR71C475KA73L MuRata 0805 10C56, C120, C127, C130, +/- 10%, X7R, 0805C134C16, C18, C19, C26, C27, CAP, CERM, 0.01 µF, 100 06031C103KAT2A AVX 0603 15C44, C45, C46, C49, C53, V, +/- 10%, X7R, 0603C59, C60, C61, C62, C65C20, C29, C34, C35, C47, CAP, CERM, 0.1 µF, 25 V, 06033C104KAT2A AVX 0603 6C63 +/- 10%, X7R, 0603C21, C28, C33, C38, C42, CAP, CERM, 1 µF, 16 V, +/- C0603C105K4PACTU Kemet 0603 6C64 10%, X5R, 0603C24, C30, C40, C57 CAP, CERM, 10 µF, 10 V, C0805C106K8PACTU Kemet 0805 4
+/- 10%, X5R, 0805C73, C74, C76, C78 CAP, CERM, 0.1 µF, 50 V, C1005X7R1H104K TDK 0402 4
+/- 10%, C0G/NP0, 0402C77 CAP, CERM, 0.012 µF, 16 GRM155R71C123KA01D MuRata 0402 1
V, +/- 10%, X7R, 0402C87, C88, C90, C91, C92 CAP, CERM, 4.7 pF, 25 V, GRM1555C1E4R7CA01D MuRata 0402 5
+/- 5%, C0G/NP0, 0402C99, C103 CAP, CERM, 220 pF, 50 V, 06035A221FAT2A AVX 0603 2
+/- 1%, C0G/NP0, 0603C100, C101 CAP, CERM, 30 pF, 100 V, GRM1885C2A300JA01D MuRata 0603 2
+/- 5%, C0G/NP0, 0603C102 CAP, CERM, 2200 pF, 50 V, C0603X222K5RACTU Kemet 0603 1
+/- 10%, X7R, 0603C109 CAP, CERM, 0.47 µF, 16 V, GRM188R71C474KA88D MuRata 0603 1
+/- 10%, X7R, 0603C112 CAP, CERM, 10 pF, 50 V, GRM1555C1H100JA01D MuRata 0402 1
+/- 5%, C0G/NP0, 0402C114 CAP, TA, 100 µF, 16 V, +/- T495D107M016ATE100 Kemet 7343-31 1
20%, 0.1 ohm, SMDC115 CAP, CERM, 47 µF, 16 V, GRM32ER61C476ME15L MuRata 1210 1
+/- 20%, X5R, 1210
28 Bill of Materials SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Cable References
Table 2-1. Bill of Materials (continued)Designator Description Part Number Manufacturer Package Qty
ReferenceC118 CAP, CERM, 3300 pF, 50 V, GRM155R71H332KA01D MuRata 0402 1
+/- 10%, X7R, 0402C119 CAP, CERM, 1 µF, 16 V, +/- C1608X7R1C105K TDK 0603 1
10%, X7R, 0603C124 CAP, TA, 22 µF, 25 V, +/- 293D226X0025D2TE3 Vishay- 7343-31 1
20%, 0.7 ohm, SMD SpragueC125 CAP, TA, 2.2 µF, 25 V, +/- 293D225X9025A2TE3 Vishay- 3216-18 1
10%, 6.3 ohm, SMD SpragueD1, D2, D4 LED, Green, SMD LTST-C190GKT Lite-On 1.6x0.8x0.8 3
mmD3 LED, Orange, SMD LTST-C190KFKT Lite-On 1.6x0.8x0.8 1
mmD8 Diode, Schottky, 40 V, 1 A, 1N5819HW-7-F Diodes Inc. SOD-123 1
SOD-123F1 Fuse, SC Protector, 12A 429007 Littlefuse 1206 1FID1, FID2, FID3 Fiducial mark. There is N/A N/A Fiducial 3
nothing to buy or mount.H1, H2, H5, H6 Standoff, Hex, 0.5"L #4-40 1902C Keystone Standoff 4
NylonJ1 Audio Jack, 3.5mm, Stereo, SJ-3523-SMT CUI Inc. Audio Jack 1
R/A, SMT SMDJ2, J4, J5, J6, J7, J8, J15, Header, 100mil, 2x1, Gold, 5-146261-1 TE Connectivity Header, 2x1, 21J16, J17, J19, J22, J26, J27, TH 100milJ30, J32, J34, J35, J39, J42,J43, J44J3, J14, J18, J33, J37, J40, Header, 100mil, 3x1, Gold, TSW-103-07-G-S Samtec 3x1 Header 7J41 THJ9, J11, J12, J13 Connector, End launch SMA, 142-0701-851 Emerson SMA End 4
50 ohm, SMT Network Power LaunchJ10 Connector, HDMI, 19-Pos 1747981-1 TE Connectivity 15.0x6.08x1 1
Recept, SMT 1.55mmJ20, J24 Header (friction lock), 0022112042 Molex Header 4x1 2
100mil, 4x1, Gold, TH keyedJ21 Header, 100mil, 16x2, Gold, TSW-116-07-G-D Samtec 16x2 Header 1
THJ23 Header, 100mil, 8x2, Gold, TSW-108-07-G-D Samtec 8x2 Header 1
THJ25 Header, 100mil, 4x1, Gold, TSW-104-07-G-S Samtec 4x1 Header 1
THJ28 Header (shrouded), 100 mil, SBH11-PBPC-D07-ST-BK Sullins 7x2 1
7x2, Gold, TH Connector ShroudedSolutions Header
J29 Connector, Receptacle, Mini- 1734035-2 TE Connectivity USB Mini 1USB Type B, R/A, Top Type BMount SMT
J31 Header, 100mil, 7x2, Tin, TH PEC07DAAN Sullins Header, 7x2, 1Connector 100mil, TinSolutions
J36 Connector, DC Jack 2.1X5.5 PJ-102A CUI Inc. POWER 1mm, TH JACK,
14.4x11x9mm
J38 Header, 100mil, 4x2, Gold, TSW-104-07-G-D Samtec 4x2 Header 1TH
L1, L2, L12, L13 1.5A Ferrite Bead, 330 ohm BLM18SG331TN1D MuRata 0603 4@ 100MHz, SMD
29SNLU169–December 2014 Bill of MaterialsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Cable References www.ti.com
Table 2-1. Bill of Materials (continued)Designator Description Part Number Manufacturer Package Qty
ReferenceL3, L5 Ferrite Bead, 1000 ohm @ BLM21AG102SN1D Murata 0805 2
100 MHz, 0.5 A, 0805L4, L6, L8 Ferrite Bead, 120 ohm @ BLM18SG121TN1D MuRata 0603 3
100 MHz, 3 A, 0603L7 Ferrite Bead, 1000 ohm @ BLM21AG102SN1D Murata 0805 1
100 MHz, 0.3 A, 0805L10, L11 Coupled inductor, 0.22 A, DLW21SN261XQ2L MuRata Inductor, 2
0.59 ohm, SMD 1.2x1.2x2.0mm
L14 Inductor, Shielded Drum 7440650047 Wurth WE-TPC- 1Core, Ferrite, 4.7uH, 4.2A, Elektronik XLH20.02 ohm, SMD eiSos
P1 Right Angle Plug for PCB, D4S20G-400A5-Z Rosenberger HSD 1TH connector,
WaterblueQ1, Q2, Q3, Q4 MOSFET, N-CH, 50 V, 0.22 BSS138 Fairchild SOT-23 4
A, SOT-23 SemiconductorR1, R2 RES, 100, 1%, 0.063 W, CRCW0402100RFKED Vishay-Dale 0402 2
0402R3, R7, R9, R10, R11, R12, RES, 0, 5%, 0.063 W, 0402 ERJ-2GE0R00X Panasonic 0402 77R13, R14, R15, R16, R21,R22, R23, R25, R26, R28,R30, R31, R32, R33, R34,R35, R36, R37, R38, R39,R40, R41, R42, R43, R106,R107, R108, R110, R113,R115, R117, R119, R120,R121, R125, R126, R127,R128, R129, R132, R133,R134, R135, R136, R137,R138, R139, R141, R142,R145, R146, R147, R148,R149, R150, R151, R152,R153, R154, R155, R156,R157, R158, R159, R160,R161, R162, R163, R198,R203, R206R4, R5, R6, R8, R103, R116, RES, 10.0 k, 1%, 0.063 W, CRCW040210K0FKED Vishay-Dale 0402 18R122, R164, R165, R166, 0402R167, R168, R169, R170,R171, R181, R184, R194R17 RES, 49.9, 1%, 0.063 W, CRCW040249R9FKED Vishay-Dale 0402 1
0402R19 RES, 4.70 k, 1%, 0.1 W, ERJ-2RKF4701X Panasonic 0402 1
0402R27, R123, R124 RES, 4.7 k, 5%, 0.063 W, CRCW04024K70JNED Vishay-Dale 0402 3
0402R49, R58, R85 RES, 118 k, 1%, 0.063 W, CRCW0402118KFKED Vishay-Dale 0402 3
0402R50, R59, R86 RES, 107 k, 1%, 0.063 W, CRCW0402107KFKED Vishay-Dale 0402 3
0402R51, R60, R87 RES, 113 k, 1%, 0.063 W, CRCW0402113KFKED Vishay-Dale 0402 3
0402R52, R61, R88 RES, 82.5 k, 1%, 0.063 W, CRCW040282K5FKED Vishay-Dale 0402 3
0402R53, R62, R89 RES, 68.1 k, 1%, 0.063 W, CRCW040268K1FKED Vishay-Dale 0402 3
0402R54, R63, R90 RES, 56.2 k, 1%, 0.063 W, CRCW040256K2FKED Vishay-Dale 0402 3
0402
30 Bill of Materials SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Cable References
Table 2-1. Bill of Materials (continued)Designator Description Part Number Manufacturer Package Qty
ReferenceR55, R64, R91 RES, 13.3 k, 1%, 0.063 W, CRCW040213K3FKED Vishay-Dale 0402 3
0402R66, R75, R93 RES, 40.2 k, 1%, 0.063 W, CRCW040240K2FKED Vishay-Dale 0402 3
0402R67, R76, R94 RES, 30.9 k, 1%, 0.063 W, CRCW040230K9FKED Vishay-Dale 0402 3
0402R68, R77, R95 RES, 51.1 k, 1%, 0.063 W, CRCW040251K1FKED Vishay-Dale 0402 3
0402R69, R78, R96 RES, 88.7 k, 1%, 0.063 W, CRCW040288K7FKED Vishay-Dale 0402 3
0402R70, R79, R97 RES, 102 k, 1%, 0.063 W, CRCW0402102KFKED Vishay-Dale 0402 3
0402R71, R80, R98 RES, 137 k, 1%, 0.063 W, CRCW0402137KFKED Vishay-Dale 0402 3
0402R72, R81, R99 RES, 210 k, 1%, 0.063 W, CRCW0402210KFKED Vishay-Dale 0402 3
0402R102 RES, 1.00 k, 1%, 0.1 W, ERJ-2RKF1001X Panasonic 0402 1
0402R111 RES, 1.0 k, 5%, 0.063 W, CRCW04021K00JNED Vishay-Dale 0402 1
0402R130, R131 RES, 47 k, 5%, 0.063 W, CRCW040247K0JNED Vishay-Dale 0402 2
0402R140 RES, 27 k, 5%, 0.063 W, CRCW040227K0JNED Vishay-Dale 0402 1
0402R172 RES, 330, 5%, 0.063 W, CRCW0402330RJNED Vishay-Dale 0402 1
0402R173, R174, R175 RES, 470, 5%, 0.063 W, CRCW0402470RJNED Vishay-Dale 0402 3
0402R176, R177 RES, 33, 5%, 0.063 W, 0402 CRCW040233R0JNED Vishay-Dale 0402 2R178, R185, R186 RES, 1.5 k, 5%, 0.063 W, CRCW04021K50JNED Vishay-Dale 0402 3
0402R179, R182 RES, 33 k, 5%, 0.063 W, CRCW040233K0JNED Vishay-Dale 0402 2
0402R180 RES, 1.2 M, 5%, 0.1 W, CRCW06031M20JNEA Vishay-Dale 0603 1
0603R183 RES, 200, 5%, 0.063 W, CRCW0402200RJNED Vishay-Dale 0402 1
0402R187 RES, 124 k, 1%, 0.063 W, CRCW0402124KFKED Vishay-Dale 0402 1
0402R188 RES, 22.1 k, 1%, 0.063 W, CRCW040222K1FKED Vishay-Dale 0402 1
0402R189, R195, R204, R207 RES, 0, 5%, 0.1 W, 0603 CRCW06030000Z0EA Vishay-Dale 0603 4R193, R196, R200, R205 RES, 100 k, 5%, 0.063 W, CRCW0402100KJNED Vishay-Dale 0402 4
0402R197 RES, 1.87 k, 1%, 0.063 W, CRCW04021K87FKED Vishay-Dale 0402 1
0402R199 RES, 4.99 k, 1%, 0.063 W, CRCW04024K99FKED Vishay-Dale 0402 1
0402R201 RES, 23.2 k, 1%, 0.063 W, CRCW040223K2FKED Vishay-Dale 0402 1
0402R202 RES, 12.1 k, 1%, 0.063 W, CRCW040212K1FKED Vishay-Dale 0402 1
0402R208 RES, 3.24 k, 1%, 0.063 W, CRCW04023K24FKED Vishay-Dale 0402 1
0402
31SNLU169–December 2014 Bill of MaterialsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Cable References www.ti.com
Table 2-1. Bill of Materials (continued)Designator Description Part Number Manufacturer Package Qty
ReferenceS1 Switch, Slide, SPST 3 poles, 219-3LPST CTS 3 poles 1
SMT Electrocompon SPSTents Switch
S2, S3, S6 Switch, Slide, SPST 8 poles, 219-8MST CTS Switch, 3SMT Electrocompon 8Pos,
ents 21.8x3.8x6.7mm
S4, S7, S9 SWITCH TACTILE SPST- EVQ-PAD04M Panasonic 6x4.3x6mm 3NO 0.02A 15V, TH
S5 DIP Switch, 4 position slide A6S-4104-H Omron SMT DIP 1actuator, SPST, SMD Electronic switch
ComponentsSH-J3, SH-J14, SH-J17, SH- Shunt, 2mm, Gold plated, 2SN-BK-G Samtec 2mm Shunt, 9J18, SH-J22, SH-J33, SH- Black Closed TopJ37, SH-J40, SH-J41U1 SINGLE-ENDED, ANALOG- PCM1808PWR Texas PW0014A 1
INPUT 24-BIT, 96-kHz InstrumentsSTEREO A/D CONVERTER,PW0014A
U2 1080p HDMI to FPD-Link III DS90UH949TRGCRQ1 Texas RGC0064K 1Bridge Serializer, InstrumentsRGC0064K
U3 Socket, DIP-8, Sleeve Pin, 110-13-308-41-001000 Mill-Max DIP-8, Body 12.54 mm Pitch 10.16x10.16
mm, Pitch2.54mm
U4 Socket, 20pin DIP STD STD DIP20 1U5 ESD-Protection Array for TPD4E004DRYRG4 Texas DRY0006A 1
High-Speed Data Interfaces, Instruments4 Channels, -40 to +85degC, 6-pin SON (DRY),Green (RoHS & no Sb/Br)
U6 Mixed Signal MSP430F5529IPN Texas PN0080A 1MicroController, PN0080A Instruments
U7 TCA9406 Dual Bidirectional TCA9406DCUR Texas DCU0008A 11-MHz I2C-BUS and SMBus InstrumentsVoltage Level-Translator,1.65 to 3.6 V, -40 to 85degC, 8-pin US8 (DCU),Green (RoHS & no Sb/Br)
U8 IC, 6-BIT BIDIRECTIONAL TXB0106PWR TI TSSOP 1VOLTAGE-LEVELTRANSLATOR
U9 IC, 4.5V-18V Input, 2-A TPS54225PWP TI PWP20 1Sync. Step-Down SWIFTConverter
U10 IC, 1.5A LDO Regulator with TPS74701DRC TI SON-10 1Soft-Start
U11 IC, Dual 1-A Low-Dropout TPS767D3xxPWP TI PWP28 1Regulator
Y1 Oscillator, ECS-8FA3-xxx-TR ECS 0.551 x 10.386 inch
Y3 Crystal, 24.000MHz, 20pF, ECS-240-20-5PX-TR ECS Inc. Crystal, 1SMD 11.4x4.3x3.8
mmC17, C41, C43, C58 CAP, CERM, 0.047 µF, 16 GRM188R71C473KA01D MuRata 0603 0
V, +/- 10%, X7R, 0603C22, C23, C31, C37, C48, CAP, CERM, 4.7 µF, 16 V, GRM21BR71C475KA73L MuRata 0805 0C51, C52, C55 +/- 10%, X7R, 0805
32 Bill of Materials SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Table 2-1. Bill of Materials (continued)Designator Description Part Number Manufacturer Package Qty
ReferenceC36, C54 CAP, CERM, 0.47 µF, 16 V, GRM188R71C474KA88D MuRata 0603 0
+/- 10%, X7R, 0603C75, C79 CAP, CERM, 12 pF, 25 V, GRM1555C1E120JA01D MuRata 0402 0
+/- 5%, C0G/NP0, 0402C80 CAP, CERM, 0.012 µF, 16 GRM155R71C123KA01D MuRata 0402 0
V, +/- 10%, X7R, 0402C86 CAP, CERM, 0.1 µF, 16 V, GRM155R71C104KA88D MuRata 0402 0
+/- 10%, X7R, 0402R18, R20, R44, R45, R46, RES, 0, 5%, 0.063 W, 0402 ERJ-2GE0R00X Panasonic 0402 0R47, R48, R56, R57, R65,R73, R74, R82, R83, R84,R92, R100, R101, R143,R144, R209, R210, R211,R212R24, R29, R104, R105 RES, 10.0 k, 1%, 0.063 W, CRCW040210K0FKED Vishay-Dale 0402 0
0402R109, R112, R114, R118 RES, 49.9, 1%, 0.063 W, CRCW040249R9FKED Vishay-Dale 0402 0
0402S8 Switch, Slide, SPST 8 poles, 219-8MST CTS Switch, 0
SMT Electrocompon 8Pos,ents 21.8x3.8x6.7
mmY2 Crystal, SMT Quart Crystal ATSxxxSM CTS 0.484 x 0
0.190 inchH3, H4, H7, H8 Machine Screw, Round, #4- NY PMS 440 0025 PH B&F Fastener Screw 4
40 x 1/4, Nylon, Philips Supplypanhead
Appendix ASNLU169–December 2014
EVM PCB Schematics
33SNLU169–December 2014 EVM PCB SchematicsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
2 10Block Diagram
10/27/2014
SV600978A_BlockDiagram.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer:
Ryan BaileyTran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
Revision History
Revision Notes
DS90Ux9x9-Q1HDMI
FPD3
FPD3
MODE_SEL
IDx
REF OSC
USB-2-ANYEDID
DDC
I2C
SPI/D_GPIO
GPIO
I2S
INTB
USB
Power
HDMI
EXT CONN
3.3V
1.8V
1.1V
Power
LEDs
Audio ADC
5V
EXT UC
Appendix A www.ti.com
34 EVM PCB Schematics SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
4 10
11/3/2014
SV600978A_DS90UB949.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
GND
10µFC30
4.7µFC31DNP
1µFC28
0.01µFC26
0.1µFC29
0.01µFC27
0
R11
0
R12
0
R15
0
R20DNP
0
R23
0
R25
0
R26
0
R28
0
R30
0
R31
0
R33
0
R35
0
R36
0
R37
0
R38
0
R39
0
R41
0
R43
0
R40
0
R42
0
R21
0
R22 0
R18DNP0
R16
IN_CLK_P
IN_D0_N
IN_D0_P
IN_D1_N
IN_D1_P
IN_D2_N
IN_D2_P
IN_CLK_N
CEC
DDC_SCL
DDC_SDA
RX_5V
HPD
VDDIO
VDD18
VTERM
I2S_CLK/GPIO8_REG
I2S_WC/GPIO7_REG
I2S_DA/GPIO6_REG
I2S_DB/GPIO5_REG
I2S_DC/GPIO2
I2S_DD/GPIO3
SDIN/GPIO0
SWC/GPIO1
SCLK
MCLK
D_GPIO0/MOSI
D_GPIO1/MISO
D_GPIO2/SPLK
D_GPIO3/SS
GND
VDDT11
VDDL11
VDDR11
SDA
SCL
IDx
MODE_SEL0
MODE_SEL1
INTB
PDB
VDD11
4.7µFC48DNP
0.01µFC49
4.7µFC50
4.7µFC51DNP
0.01µFC44
10µFC40
0.01µFC45
0.01µFC46
0.1µFC47
0.047µFC41DNP
1µFC42
0.047µFC43DNP
GND
0.1µFC63
1µFC64
0.01µFC65
0.01µFC60
10µFC57
0.01µFC61
0.01µFC62
0.047µFC58DNP
0.01µFC59
GND
4.7µFC22DNP
4.7µFC23DNP
10µFC24
0.01µFC19
0.01µFC16
0.1µFC20
1µFC21
0.047µFC17DNP
0.01µFC18
GND
VDD1V8
4.7µFC37DNP
1µFC38
0.1µFC35
1µFC33
0.47µFC36DNP
0.1µFC34
GND
4.7µFC55DNP
0.47µFC54DNP
0.01µFC53
GND
VTERMc
1000 ohm
L3
1000 ohm
L5
1000 ohm
L7
VDDIO
VTERM
VDD18120 ohm
L4
120 ohm
L6
120 ohm
L8
VDDL11
VDDR11
VDDT11
49.9
R17
DOUT0_P
DOUT0_N
DOUT1_P
DOUT1_N
VDDIO
4.7k
R27
0
R340
R32
0
R13
0
R14
12
Y2 ATSxxxSM
DNP
GND
RES0_0
RES0_1
4.7µFC56
4.7µFC39
4.7µFC25
4.7µFC52DNP
4.7µFC32
4.7µFC15
TP1TP2
GND
10.0k
R24DNPDNP
10.0k
R29DNPDNP
GND
0
R44DNP
0
R45DNP
0
R46DNP
0
R47DNP
12pF
C75
DNP
12pF
C79
DNP
0.1µF
C73
0.1µF
C74
0.1µF
C76
0.1µF
C78
0.012µF
C77
0.012µFC80DNP
IN_D1_PIN_D2_N
IN_D1_NIN_D0_P
IN_D0_N
IN_CLK_P
IN_CLK_N
IN_D2_P
DOUT0_A_PDOUT0_A_N
DOUT1_B_P
DOUT1_B_N
DOUT0_P
VDD18
VDDIO
VTERM
VDDL11
VDDR11
VDDT11
DOUT0_N
DOUT1_P
DOUT1_N
GND
1 2
J45-146261-1
CEC1
RES02
VDDIO3
SDIN/GPIO04
SWC/GPIO15
SCLK/I2CSEL6
VDDL117
D_GPIO0/MOSI8
VDDA119
D_GPIO1/MOSO10
D_GPIO2/SPLK11
D_GPIO3/SS12
INTB13
SDA14
SCL15
MCLK16
VDDP1117
MODE_SEL018
IDX19
LFT20
VDDHS1121
DOUT1-22
DOUT1+23
VDD1824
VDDS1125
DOUT0-26
DOUT0+27
VDDHS1128
RES129
RES230
PDB31
MODE_SEL132
I2S_WC/GPIO7_REG33
I2S_CLK/GPIO8_REG34
I2S_DA/GPIO6_REG35
I2S_DB/GPIO5_REG36
I2S_DC/GPIO237
I2S_DD/GPIO338
X139
RES340
VDDL1141
HPD42
RX_5V43
DDC_SDA44
DDC_SCL45
VDDIO46
NC047
NC148
IN_CLK-49
IN_CLK+50
VDD1851
VDDHA1152
RES453
VDDHA1154
IN_D0-55
IN_D0+56
VTERM57
VDDHA1158
IN_D1-59
IN_D1+60
VDDHA1161
IN_D2-62
IN_D2+63
VDD1864
DAP65
U2
DS90UH949TRGCRQ1
4.70kR19
VDDIO
www.ti.com Appendix A
35SNLU169–December 2014 EVM PCB SchematicsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
1 1
11/4/2014
SV600978A_MSP430F5529.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
24MHz
12
Y3ECS-240-20-5PX-TR
GPIO11/VEREF+
GPIO10/VEREF-
GND
GND
DP
PUR
DM
VUSB
V18
GPIO1/I2C(SCL)
GPIO0/I2C(SDA)
GPIO7/PWM0
GPIO3/PWM2
SDABRD
SCLBRD
AIN_B_0
AIN_B_1
GPIO9/ADC2
GPIO8/ADC3
30pF
C100
30pF
C101
2200pFC102
GND
33k
R182
GND
GND
GND
GND
GND
BSL
DM
DP
PUR
V18
33R177
33
R176
GND
1.2M
R180
GND
33k
R179
GND
220pFC103
GND
1.5k
R185
1.5k
R186
0.47µFC109
0.1µFC108
0.1µFC104
0.1µFC105
Green
12
D4
200
R183
GND
1
2
J30
5-146261-1
VDD33330 ohm
L13 VDD33_UC
VDD33_UC
VDD33_UC
VDD33_UC
0.1µFC107
10µFC106
SDA_B1
GND2
VCCA3
SDA_A4
SCL_A5
OE6
VCCB7
SCL_B8
U7
TCA9406DCUR
GND
10.0k
R184
0.1µFC110
0.1µFC111
VDD33_UC
VDD_I2C
A11
VCCA2
A23
A34
A45
A56
A67
OE8
GND9
B610
B511
B412
B313
B214
VCCB15
B116
U8
TXB0106PWR
GND
GPIO5/SPI(SOMI)/UART(RXD)
GPIO4/SPI(SIMO)/UART(TXD)
GPIO2/SPI(SCLK)
GPIO6/PWM1/SPI(CS)
INTB_CTRL
PDB_CTRL
GND
0.1µFC96
0.1µFC97
VDD33_UC
10.0k
R181
SOMI
SIMO
SCLK
CS
0.1µFC98
INTB
INTBINTB
220pFC99
GND
VUSB
41
32
S9
EVQ-PAD04M
1 2
J43
5-146261-1
1
2
J44
5-146261-1
PDB
VDDIO
CS
SCLK
SIMO
SOMI
1 2F1
429007
VBUS
VBUS
PDB
2
3
4
1
5
J29
1734035-2
1.5k
R178
1
23
Q4
12
34
56
78
910
11
12
13
14
J31
IO1
1
IO2
2
GND
3IO3
4
IO4
5VCC
6
U5
P6.4/CB4/A41
P6.5/CB5/A52
P6.6/CB6/A63
P6.7/CB7/A74
P7.0/CB8/A125
P7.1/CB9/A136
P7.2/CB10/A147
P7.3/CB11/A158
P5.0/A8/VREF+/VEREF+9
P5.1/A9/VREF-/VEREF-10
AVCC111
P5.4/XIN12
P5.5/XOUT13
AVSS114
P8.015
P8.116
P8.217
DVCC118
DVSS119
VCORE20
P1.0/TA0CLK/ACLK
21
P1.1/TA0.0
22
P1.2/TA0.1
23
P1.3/TA0.2
24
P1.4/TA0.3
25
P1.5/TA0.4
26
P1.6/TA1CLK/CBOUT
27
P1.7/TA1.0
28
P2.0/TA1.1
29
P2.1/TA1.2
30
P2.2/TA2CLK/SMCLK
31
P2.3/TA2.0
32
P2.4/TA2.1
33
P2.5/TA2.2
34
P2.6/RTCCLK/DMAE0
35
P2.7/UCB0STE/UCA0CLK
36
P3.0/UCB0SIMO/UCB0SDA
37
P3.1/UCB0SOMI/UCB0SCL
38
P3.2/UCB0CLK/UCA0STE
39
P3.3/UCA0TXD/UCA0SIMO
40
P3.4/UCA0RXD/UCA0SOMI41
P3.5/TB0.542
P3.6/TB0.643
P3.7/TB0OUTH/SVMOUT44
P4.0/PM_UCB1STE/PM_UCA1CLK45
P4.1/PM_UCB1SIMO/PM_UCB1SDA46
P4.2/PM_UCB1SOMI/PM_UCB1SCL47
P4.3/PM_UCB1CLK/PM_UCA1STE48
DVSS249
DVCC250
P4.4/PM_UCA1TXD/PM_UCA1SIMO51
P4.5/PM_UCA1RXD/PM_UCA1SOMI52
P4.6/PM_NONE53
P4.7/PM_NONE54
P5.6/TB0.055
P5.7/TB0.156
P7.4/TB0.257
P7.5/TB0.358
P7.6/TB0.459
P7.7/TB0CLK/MCLK60
VSSU
61
PU.0/DP
62
PUR
63
PU.1/DM
64
VBUS
65
VUSB
66
V18
67
AVSS2
68
P5.2/XT2IN
69
P5.3/XT2OUT
70
TEST/SBWTCK
71
PJ.0/TDO
72
PJ.1/TDI/TCLK
73
PJ.2/TMS
74
PJ.3/TCK
75
RST/NMI/SBWTDIO
76
P6.0/CB0/A0
77
P6.1/CB1/A1
78
P6.2/CB2/A2
79
P6.3/CB3/A3
80
U6
MSP430F5529IPN
Appendix A www.ti.com
36 EVM PCB Schematics SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
3 10
11/2/2014
SV600978A_EXT_UC.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
VDD1V8
0.1µFC94
GND
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
U4
SOCKET_20P_DIP
GND
SDA
SCL0
R155
0
R157
INTB
0
R1530
R1510
R1490
R147
0
R161
0
R163
0
R162
0
R1580
R1560
R1540
R1520
R1500
R1480
R146
SW1
SW2
SW3
SW0 SW4
SW5
SW6
SW7
D_GPIO0/MOSI
D_GPIO1/MISO
D_GPIO2/SPLK
D_GPIO3/SS
TEST
RST
0
R159
0
R160
0
R145
10.0k
R171
10.0k
R170
10.0k
R169
10.0k
R168
10.0k
R167
10.0k
R166
10.0k
R165
10.0k
R164
SW0SW1SW2SW3SW4SW5SW6SW7
12
34
56
78
910
1112
1314
J28
SBH11-PBPC-D07-ST-BK
GND
RST
10µFC93
TEST
330
R172
GND
1
2
J27
5-146261-1
330 ohm
L12 VDD_UC
VDD_UC
VDD_UC
0.1µF
C95
1
2
3
4
5
6
13
14
15
16
7
12
89
10
11
DNPS8
219-8MST
DNP
GND
41
32
S7
EVQ-PAD04M
www.ti.com Appendix A
37SNLU169–December 2014 EVM PCB SchematicsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
6 10
11/5/2014
SV600978A_CONFIG.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
MODE_SEL0
MODE_SEL1
IDx
VDD1V8
0
R48DNP
GNDGND
VDD1V8
0
R84DNP
GNDGND
VDD1V8
GNDGND
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
0x18
0x1C
0x20
0x24
0x28
0x2C
0x30
0x34
0x0C
0x0E
0x10
0x12
0x14
0x16
0x18
0x20
7'b
8'b
I2C Address Select (IDx)Mode Select 0 (MODE_SEL0)
Mode Select 1 (MODE_SEL1)
631
8
27 5
4
S5A6S-4104-H
GND
10.0k
R102
10.0k
R104DNP
DNP
10.0k
R105DNP
VDDIO
PDB
INTB
Mode Switches
0.1µFC84
0.1µFC81
GND
GND
0.1µFC82
GND
GND
0
R92DNP
0
R101DNP
0
R100DNP
0
R56DNP
0
R74DNP
0
R73DNP
0
R57DNP
0
R65DNP
0
R83DNP
0
R82DNP
SCLK
0
R107
10µFC83
GND
0
R106
10.0k
R103
PDB
INTB
SCLK
RES
1 2 3 4 5 6
13
14
15
16
7
12
8910
11
S6219-8MST
1 2 3 4 5 6
13
14
15
16
7
12
8910
11
S2219-8MST
1 2 3 4 5 6
13
14
15
16
7
12
8910
11
S3219-8MST
41
32
S4
EVQ-PAD04M
1
2
J5
5-146261-1
1
2
J6
5-146261-1
1
2
J7
5-146261-1
1
2
J8
5-146261-1
118kR49
1
118kR85
118kR58
1
30.9kR67
30.9kR76
30.9kR94
107kR50
107kR86
107kR59
51.1kR68
51.1kR77
51.1kR95
113kR51
113kR60
113kR87
88.7kR69
88.7kR96
88.7kR78
82.5kR52
82.5kR61
82.5kR88
102kR70
102kR79
102kR97
68.1kR62
68.1kR53
68.1kR89
137kR71
137kR80
137kR98
56.2kR54
56.2kR63
56.2kR90
210kR72
210kR81
210kR99
40.2kR66
40.2kR75
40.2kR93
13.3kR55
13.3kR64
13.3kR91
Assembly NoteZZ13
For S2 activate switch between pins 1 and 16
Assembly NoteZZ14
For S6 activate switch between pins 1 and 16
Assembly NoteZZ15
For S3 activate switch between pins 1 and 16
Appendix A www.ti.com
38 EVM PCB Schematics SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
7 10
11/9/2014
SV600978A_CONNECTORS.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
1
2345
J11142-0701-851
1
2345
J12142-0701-851
1
2345
J13142-0701-851 GND GND
GNDGND
DOUT0_P
DOUT0_N
DOUT1_P
DOUT1_N
49.9
R118DNP
49.9
R114DNP
49.9
R112DNP
49.9
R109DNP
GND
GND
IN_CLK_P
IN_D0_N
IN_D0_P
IN_D1_N
IN_D1_P
IN_D2_N
IN_D2_P
IN_CLK_N
CEC
DDC_SCL
DDC_SDA
RX_5V
HPD
GND GND
VDD_DDC
0.1µFC85
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
J23
TSW-108-07-G-D
0
R132
0
R135
0
R137
0
R138
0
R139
0
R141
0
R143DNP
0
R144DNP
PDB
D_GPIO0/MOSI
D_GPIO1/MISO
D_GPIO2/SPLK
D_GPIO3/SS
INTB
SDA
SCLGPIO1/I2C(SCL)
GPIO0/I2C(SDA)
GPIO2/SPI(SCLK)
GPIO6/PWM1/SPI(CS)
GPIO4/SPI(SIMO)/UART(TXD)
GPIO5/SPI(SOMI)/UART(RXD)
PDB_CTRL
INTB_CTRL
0
R113
0
R115
0
R117
0
R119
0
R120
0
R121
0
R125
0
R128 4
1
2
3
J20
0022112042
4
1
2
3
J24
0022112042
1
2
J26
5-146261-1
GND
GND
GND
4.7pFC88
4.7pFC87
4.7pFC90
4.7pFC91
4.7pFC92
0
R142
0
R134
0
R136
0
R126
0R127
CEC
DDC_SCL
DDC_SDA
SDA
SCL
1
2
J17
5-146261-1
1
2
J22
5-146261-1
VDD_I2C
VDD_DDC
0.1µFC86DNP
0.1µFC89
GND
GND
RES0_0
RES0_1
GND
GND
GND
I2S_CLK/GPIO8_REG
I2S_WC/GPIO7_REG
I2S_DA/GPIO6_REG
I2S_DB/GPIO5_REG
I2S_DC/GPIO2
I2S_DD/GPIO3
VDDIO
SDIN/GPIO0
SWC/GPIO1
SCLK
MCLK
0
R133
D_GPIO0/MOSI
D_GPIO1/MISO
D_GPIO2/SPLK
D_GPIO3/SS
1
2
J15
5-146261-1
INTB
GND
0
R129
0
R108
0
R110
TP3
1
2
J19
5-146261-1
RX_5V
GND
1
2
J16
5-146261-1
HPD
GND
4
1
2
3
J25
TSW-104-07-G-S
DAOUT
BCK
LRCK
SCKIN
4.7k
R124
4.7k
R123
47k
R130
47k
R131
27k
R140
VDD33
10.0k
R116
10.0k
R122
1
2
3
J14
TSW-103-07-G-S
1
2
3
J18
TSW-103-07-G-S
VDDIO
VDDIO
1.0k
R111
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15
17
19
21
23
25
27
29
31
16
18
20
22
24
26
28
30
32
J21
TSW-116-07-G-D
IN_CLK_N
IN_CLK_P
IN_D0_N
IN_D0_P
IN_D1_N
IN_D1_PIN_D2_N
IN_D2_P
DOUT1_N
DOUT1_P
DOUT0_N
DOUT0_P
J10_12_N
J10_12_P
J10_9_N
J10_9_P
J10_6_N
J10_6_PJ10_3_N
J10_3_P
1 234
L10DLW21SN261XQ2L
1 234
L11
DLW21SN261XQ2L
1
2
23
21
20
22
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
J101747981-1
1
2345
J9142-0701-851
GND
SMAD0_NSMAD0_P
SMAD1_NSMAD1_P
SMAD0_N
SMAD0_P
SMAD1_N
SMAD1_P
0
R209DNP
0
R210DNP
0
R211DNP
0
R212DNP
SH-J14
SH-J17
SH-J18
SH-J22
2
1
4
3
PAIR A1
PAIR A2
EMITTER
P1D4S20G-400A5-Z
1
2
3
4 5
6
7
8
U3
Assembly NoteZZ5
Jumper SH-J14 connects Pin 2 and 3 for Header J14
Assembly NoteZZ6
Jumper SH-J17 connects Pin 1 and 2 for Header J17
Assembly NoteZZ7
Jumper SH-J18 connects Pin 2 and 3 for Header J18
Assembly NoteZZ8
Jumper SH-J22 connects Pin 1 and 2 for Header J22
www.ti.com Appendix A
39SNLU169–December 2014 EVM PCB SchematicsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
8 10
11/4/2014
SV600978A_LED.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
GND
Green
12
D2
GND
INTB
RX_5V
HPD
Green
12
D1
GND
VDD5V
470
R173
470
R174
470
R175
H4
NY PMS 440 0025 PH
H7
NY PMS 440 0025 PH
H8
NY PMS 440 0025 PH
H2
1902C
H5
1902C
H6
1902C
FID2
FID1
FID3
SV600978
A
PCB Number:
PCB Rev:
Label Assembly NoteZZ1
This Assembly Note is for PCB labels only
Assembly NoteZZ2
These assemblies are ESD sensitive, ESD precautions shall be observed
Assembly NoteZZ3
These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
Assembly NoteZZ4
These assmblies must comply with workmanship standards IPC-A-610 Class 2, unless otherwise specified.
Board Silkscreen Label: "Not for EMI Testing"
LOGOPCB
Texas Instruments
Orange
12
D3
H1
1902CH3
NY PMS 440 0025 PH
LOGOPCB
Pb-Free Symbol
LOGOPCB
FCC disclaimer
1
23
Q1
1
23
Q2
1
23
Q3
Appendix A www.ti.com
40 EVM PCB Schematics SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
10 10
11/5/2014
SV600978A_Audio_IF.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
3
1
2
J1
SJ-3523-SMT
10µFC11
10µFC6
0.1µFC7
0.1µFC12
GND
GND
10µFC2
0.1µFC3
VDD33
10µFC10
10µFC5
330 ohm
L1
330 ohm
L2
VDD5V
GND
0.01µFC9
100
R2
100
R1
GND
GND
16 S1A
219-3LPST
25
S1B
219-3LPST34
S1C219-3LPST
GND
10.0k
R5
10.0k
R6
10.0k
R4
VDD33
FMT
MD1
MD0
FMTMD1MD0
0
R7
0
R9
0
R3
0.1µFC14
GND 123J3
TSW-103-07-G-S0
R10
DAOUT
BCK
LRCK
SCKIN
10.0k
R810µFC13
TRI-ST1
GND
2
OUT3V
DD
4 Y1ECS-8FA3-xxx-TR GND
1
0.01µFC1
1µF
C4
1µF
C8
1
2
J2
5-146261-1
SH-J3
VREF1
AGND2
VCC3
VDD4
DGND5
SCKI6
LRCK7
BCK8
DOUT9
MD010
MD111
FMT12
VINL13
VINR14
U1
PCM1808PWR
Assembly NoteZZ16
Jumper SH-J3 connects Pin 2 and 3 for Header J3
www.ti.com Appendix A
41SNLU169–December 2014 EVM PCB SchematicsSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
9 10
11/5/2014
SV600978A_Power.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
DS90UB949-Q1EVMProject Title:Designed for: Public Release
Assembly Variant: 004
© Texas Instruments 2014
Drawn By:Engineer: Tran Dam
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:SV600978Number: Rev: A
1
3
2
J36
PJ-102A
GND
0.1µFC126
GND
1 2
3 4
5 6
7 8
J38
GND
GND
VDD33
VDD_EXT
GND
0.1µFC121
GND
4.7µFC120
0.1µFC122
GND
4.7µFC127
0.01µFC128
TP10100k
R196
0
R198
0.1µFC129 4.99k
R199
1.87k
R197
VDD11VDD5V
U11
TPS767D3XXPWP
GND
GND
GND
100k
R200
100k
R205
TP12
TP15
TESTPOINT
TP16
TP13
0
R203
0
R206
12.1k
R202 GND23.2k
R201
0.1µFC131
4.7µFC130
0.1µFC135
4.7µFC134
10µFC123
10µFC133
0.1µFC132
GND
10µFC137
0.1µFC136
GND
VDD5V
VDD33
VDD1V8
100k
R193
GND
3300pFC118
1µFC119
10.0k
R194
4.7µH
L14
7440650047
10pF
C112
10µFC116
0.1µFC117
GND
VDD5V
GND
TP14
TP17
TP7
TP5
VDD_EXT
TP9
1
2
J34
5-146261-1
GND
1
2
3
J37
TSW-103-07-G-S
VDD_I2C
1
2
3
J41
TSW-103-07-G-S
VDD_DDC
RX_5V
1
2
3
J40
TSW-103-07-G-S
VTERMc
VDD33
VDD33
VDD1V8
VDD1V8
VDD33
1
2
3
J33
TSW-103-07-G-S
1
2
J35
5-146261-1
0
R195
0
R204
0
R207
1
2
J42
5-146261-1
1
2
J39
5-146261-1
1
2
J32
5-146261-1
0
R189
0.1µF
C113
124k
R187
22.1k
R188
GND
3.24kR208
100µFC114
1
47µFC115
22µFC124
2.2µFC125
D8
1N5819HW-7-F
VBUS
SH-J33
SH-J37
SH-J40
SH-J41
VOUT1
VFB2
VREG53
SS4
GND5
PG6
EN7
PGND18
PGND29
SW110
SW211
VBST12
VIN13
VCC14
PWPD
15
U9
TPS54225PWP
IN1
IN2
PG3
BIAS4
EN5
GND6
SS7
FB8
OUT9
OUT10
PWPD
11
U10
TPS74701DRC
Assembly NoteZZ9
Jumper SH-J33 connects Pin 1 and 2 for Header J33
Assembly NoteZZ10
Jumper SH-J37 connects Pin 2 and 3 for Header J37
Assembly NoteZZ11
Jumper SH-J40 connects Pin 2 and 3 for Header J40
Assembly NoteZZ12
Jumper SH-J41 connects Pin 2 and 3 for Header J41
Appendix A www.ti.com
42 EVM PCB Schematics SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Appendix BSNLU169–December 2014
Board Layout
Board Layers
43SNLU169–December 2014 Board LayoutSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Appendix B www.ti.com
44 Board Layout SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Appendix B
45SNLU169–December 2014 Board LayoutSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Appendix B www.ti.com
46 Board Layout SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com Appendix B
47SNLU169–December 2014 Board LayoutSubmit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Revision History www.ti.com
Revision HistoryNOTE: Page numbers for previous revisions may differ from page numbers in the current version.
DATE REVISION NOTESDecember 2014 * Initial release
48 Revision History SNLU169–December 2014Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.Acceptance of the EVM is expressly subject to the following terms and conditions.1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are notfinished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. Forclarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditionsset forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or productionsystem.
2 Limited Warranty and Related Remedies/Disclaimers:2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatmentby an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in anyway by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications orinstructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or asmandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during thewarranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects torepair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shallbe warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) daywarranty period.
3 Regulatory Notices:3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kitto determine whether to incorporate such items in a finished product and software developers to write software applications foruse with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unlessall required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not causeharmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit isdesigned to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority ofan FCC license holder or must secure an experimental authorization under part 5 of this chapter.3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment.
FCC Interference Statement for Class A EVM devicesNOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required tocorrect the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devicesNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or moreof the following measures:
• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that maycause undesired operation of the device.
Concernant les EVMs avec appareils radio:Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doitaccepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna typeand its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary forsuccessful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna typeslisted in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibitedfor use with this device.
Concernant les EVMs avec antennes détachablesConformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type etd'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillageradioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotroperayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Leprésent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans lemanuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antennenon inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation del'émetteur
3.3 Japan3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certifiedby TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law ofJapan to follow the instructions below with respect to EVMs:1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule forEnforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect toEVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japanwith respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please notethat if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けていないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。2. 実験局の免許を取得後ご使用いただく。3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社東京都新宿区西新宿6丁目24番1号西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER4 EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOTLIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handlingor using the EVM, including without limitation any warning or restriction notices. The notices contain important safety informationrelated to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable andcustomary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to inputand output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, orproperty damage. If there are questions concerning performance ratings and specifications, User should contact a TIfield representative prior to connecting interface electronics including input power and intended loads. Any loads appliedoutside of the specified output range may also result in unintended and/or inaccurate operation and/or possiblepermanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting anyload to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuitcomponents may have elevated case temperatures. These components include but are not limited to linear regulators,switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using theinformation in the associated documentation. When working with the EVM, please be aware that the EVM may becomevery warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with thedangers and application risks associated with handling electrical mechanical components, systems, and subsystems.User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronicand/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safelylimit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility andliability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors ordesignees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes allresponsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility andliability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and localrequirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurateas possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites asaccurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER6. Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THEDESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHERWARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIEDWARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANYTHIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS ANDCONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANYOTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRDPARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANYINVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OFTHE EVM.
7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITSLICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANYHANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATIONSHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANYOTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8. Limitations on Damages and Liability:8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESETERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HASBEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITEDTO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODSOR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALLBE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATIONARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVMPROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDERTHESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCEOF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS ANDCONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not ina resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicableorder, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating tothese terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive reliefin any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products ApplicationsAudio www.ti.com/audio Automotive and Transportation www.ti.com/automotiveAmplifiers amplifier.ti.com Communications and Telecom www.ti.com/communicationsData Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computersDLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-appsDSP dsp.ti.com Energy and Lighting www.ti.com/energyClocks and Timers www.ti.com/clocks Industrial www.ti.com/industrialInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Security www.ti.com/securityPower Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defenseMicrocontrollers microcontroller.ti.com Video and Imaging www.ti.com/videoRFID www.ti-rfid.comOMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.comWireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2015, Texas Instruments Incorporated